rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
diff --git a/include/configs/utx8245.h b/include/configs/utx8245.h
index 4355e1c..6e9c27c 100644
--- a/include/configs/utx8245.h
+++ b/include/configs/utx8245.h
@@ -55,7 +55,7 @@
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 57600
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_BOOTDELAY 2
#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n", bootdelay
@@ -63,7 +63,7 @@
#define CONFIG_BOOTARGS "root=/dev/ram console=ttyS0,57600" /* RAMdisk */
#define CONFIG_ETHADDR 00:AA:00:14:00:05 /* UTX5 */
#define CONFIG_SERVERIP 10.8.17.105 /* Spree */
-#define CFG_TFTP_LOADADDR 10000
+#define CONFIG_SYS_TFTP_LOADADDR 10000
#define CONFIG_EXTRA_ENV_SETTINGS \
"kernel_addr=FFA00000\0" \
@@ -121,16 +121,16 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x00100000 /* Default load address */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */
/*-----------------------------------------------------------------------
@@ -142,7 +142,7 @@
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_NET_MULTI
#define CONFIG_EEPRO100
-#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_EEPRO100_SROM_WRITE
#define PCI_ENET0_IOADDR 0xF0000000
@@ -161,61 +161,61 @@
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_MAX_RAM_SIZE 0x10000000 /* 256MB */
-/*#define CFG_VERY_BIG_RAM 1 */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 /* 256MB */
+/*#define CONFIG_SYS_VERY_BIG_RAM 1 */
/* FLASH_BASE is FF800000, with 4MB on RCS0, but the reset vector
* is actually located at FFF00100. Therefore, U-Boot is
* physically located at 0xFFB0_0000, but is also mirrored at
* 0xFFF0_0000.
*/
-#define CFG_RESET_ADDRESS 0xFFF00100
+#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-#define CFG_EUMB_ADDR 0xFC000000
+#define CONFIG_SYS_EUMB_ADDR 0xFC000000
-#define CFG_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-/*#define CFG_DRAM_TEST 1 */
-#define CFG_MEMTEST_START 0x00003000 /* memtest works on 0...256 MB */
-#define CFG_MEMTEST_END 0x0ff8ffa7 /* in SDRAM, skips exception */
+/*#define CONFIG_SYS_DRAM_TEST 1 */
+#define CONFIG_SYS_MEMTEST_START 0x00003000 /* memtest works on 0...256 MB */
+#define CONFIG_SYS_MEMTEST_END 0x0ff8ffa7 /* in SDRAM, skips exception */
/* vectors and U-Boot */
/*--------------------------------------------------------------------
* Definitions for initial stack pointer and data area
*------------------------------------------------------------------*/
-#define CFG_INIT_DATA_SIZE 128 /* Size in bytes reserved for */
+#define CONFIG_SYS_INIT_DATA_SIZE 128 /* Size in bytes reserved for */
/* initial data */
-#define CFG_INIT_RAM_ADDR 0x40000000
-#define CFG_INIT_RAM_END 0x1000
-#define CFG_INIT_DATA_OFFSET (CFG_INIT_RAM_END - CFG_INIT_DATA_SIZE)
-#define CFG_GBL_DATA_SIZE 128
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
+#define CONFIG_SYS_INIT_RAM_END 0x1000
+#define CONFIG_SYS_INIT_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_INIT_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
/*--------------------------------------------------------------------
* NS16550 Configuration
*------------------------------------------------------------------*/
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_REG_SIZE 1
#if (CONFIG_CONS_INDEX == 1 || CONFIG_CONS_INDEX == 2)
-# define CFG_NS16550_CLK get_bus_freq(0)
+# define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#else
-# define CFG_NS16550_CLK 33000000
+# define CONFIG_SYS_NS16550_CLK 33000000
#endif
-#define CFG_NS16550_COM1 (CFG_EUMB_ADDR + 0x4500)
-#define CFG_NS16550_COM2 (CFG_EUMB_ADDR + 0x4600)
-#define CFG_NS16550_COM3 0xFF000000
-#define CFG_NS16550_COM4 0xFF000008
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4600)
+#define CONFIG_SYS_NS16550_COM3 0xFF000000
+#define CONFIG_SYS_NS16550_COM4 0xFF000008
/*--------------------------------------------------------------------
* Low Level Configuration Settings
@@ -225,10 +225,10 @@
*------------------------------------------------------------------*/
#define CONFIG_SYS_CLK_FREQ 33000000
-#define CFG_HZ 1000
+#define CONFIG_SYS_HZ 1000
-/*#define CFG_ETH_DEV_FN 0x7800 */
-/*#define CFG_ETH_IOBASE 0x00104000 */
+/*#define CONFIG_SYS_ETH_DEV_FN 0x7800 */
+/*#define CONFIG_SYS_ETH_IOBASE 0x00104000 */
/*--------------------------------------------------------------------
* I2C Configuration
@@ -236,13 +236,13 @@
#if 1
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
#endif
#define CONFIG_RTC_PCF8563 1 /* enable I2C support for */
/* Philips PCF8563 RTC */
-#define CFG_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */
/*--------------------------------------------------------------------
* Memory Control Configuration Register values
@@ -250,59 +250,59 @@
*------------------------------------------------------------------*/
/**** MCCR1 ****/
-#define CFG_ROMNAL 0
-#define CFG_ROMFAL 10 /* (tacc=70ns)*mem_freq - 2,
+#define CONFIG_SYS_ROMNAL 0
+#define CONFIG_SYS_ROMFAL 10 /* (tacc=70ns)*mem_freq - 2,
mem_freq = 100MHz */
-#define CFG_BANK7_ROW 0 /* SDRAM bank 7-0 row address */
-#define CFG_BANK6_ROW 0 /* bit count */
-#define CFG_BANK5_ROW 0
-#define CFG_BANK4_ROW 0
-#define CFG_BANK3_ROW 0
-#define CFG_BANK2_ROW 0
-#define CFG_BANK1_ROW 2
-#define CFG_BANK0_ROW 2
+#define CONFIG_SYS_BANK7_ROW 0 /* SDRAM bank 7-0 row address */
+#define CONFIG_SYS_BANK6_ROW 0 /* bit count */
+#define CONFIG_SYS_BANK5_ROW 0
+#define CONFIG_SYS_BANK4_ROW 0
+#define CONFIG_SYS_BANK3_ROW 0
+#define CONFIG_SYS_BANK2_ROW 0
+#define CONFIG_SYS_BANK1_ROW 2
+#define CONFIG_SYS_BANK0_ROW 2
/**** MCCR2, refresh interval clock cycles ****/
-#define CFG_REFINT 480 /* 33 MHz SDRAM clock was 480 */
+#define CONFIG_SYS_REFINT 480 /* 33 MHz SDRAM clock was 480 */
/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
-#define CFG_BSTOPRE 1023 /* burst to precharge[0..9], */
+#define CONFIG_SYS_BSTOPRE 1023 /* burst to precharge[0..9], */
/* sets open page interval */
/**** MCCR3 ****/
-#define CFG_REFREC 7 /* Refresh to activate interval, trc */
+#define CONFIG_SYS_REFREC 7 /* Refresh to activate interval, trc */
/**** MCCR4 ****/
-#define CFG_PRETOACT 2 /* trp */
-#define CFG_ACTTOPRE 7 /* trcd + (burst length - 1) + trdl */
-#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */
-#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type, sequential */
-#define CFG_ACTORW 2 /* trcd min */
-#define CFG_DBUS_SIZE2 1 /* set for 8-bit RCS1, clear for 32,64 */
-#define CFG_REGISTERD_TYPE_BUFFER 1
-#define CFG_EXTROM 0 /* we don't need extended ROM space */
-#define CFG_REGDIMM 0
+#define CONFIG_SYS_PRETOACT 2 /* trp */
+#define CONFIG_SYS_ACTTOPRE 7 /* trcd + (burst length - 1) + trdl */
+#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */
+#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type, sequential */
+#define CONFIG_SYS_ACTORW 2 /* trcd min */
+#define CONFIG_SYS_DBUS_SIZE2 1 /* set for 8-bit RCS1, clear for 32,64 */
+#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
+#define CONFIG_SYS_EXTROM 0 /* we don't need extended ROM space */
+#define CONFIG_SYS_REGDIMM 0
/* calculate according to formula in sec. 6-22 of 8245 UM */
-#define CFG_PGMAX 50 /* how long the 8245 retains the */
+#define CONFIG_SYS_PGMAX 50 /* how long the 8245 retains the */
/* currently accessed page in memory */
/* was 45 */
-#define CFG_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note */
+#define CONFIG_SYS_SDRAM_DSCD 0x20 /* SDRAM data in sample clock delay - note */
/* bits 7,6, and 3-0 MUST be 0 */
#if 0
-#define CFG_DLL_MAX_DELAY 0x04
+#define CONFIG_SYS_DLL_MAX_DELAY 0x04
#else
-#define CFG_DLL_MAX_DELAY 0
+#define CONFIG_SYS_DLL_MAX_DELAY 0
#endif
#if 0 /* need for 33MHz SDRAM */
-#define CFG_DLL_EXTEND 0x80
+#define CONFIG_SYS_DLL_EXTEND 0x80
#else
-#define CFG_DLL_EXTEND 0
+#define CONFIG_SYS_DLL_EXTEND 0
#endif
-#define CFG_PCI_HOLD_DEL 0x20
+#define CONFIG_SYS_PCI_HOLD_DEL 0x20
/* Memory bank settings.
@@ -312,94 +312,94 @@
* address. Refer to the MPC8245 user manual.
*/
-#define CFG_BANK0_START 0x00000000
-#define CFG_BANK0_END (CFG_MAX_RAM_SIZE/2 - 1)
-#define CFG_BANK0_ENABLE 1
-#define CFG_BANK1_START CFG_MAX_RAM_SIZE/2
-#define CFG_BANK1_END (CFG_MAX_RAM_SIZE - 1)
-#define CFG_BANK1_ENABLE 1
-#define CFG_BANK2_START 0x3ff00000 /* not available in this design */
-#define CFG_BANK2_END 0x3fffffff
-#define CFG_BANK2_ENABLE 0
-#define CFG_BANK3_START 0x3ff00000
-#define CFG_BANK3_END 0x3fffffff
-#define CFG_BANK3_ENABLE 0
-#define CFG_BANK4_START 0x3ff00000
-#define CFG_BANK4_END 0x3fffffff
-#define CFG_BANK4_ENABLE 0
-#define CFG_BANK5_START 0x3ff00000
-#define CFG_BANK5_END 0x3fffffff
-#define CFG_BANK5_ENABLE 0
-#define CFG_BANK6_START 0x3ff00000
-#define CFG_BANK6_END 0x3fffffff
-#define CFG_BANK6_ENABLE 0
-#define CFG_BANK7_START 0x3ff00000
-#define CFG_BANK7_END 0x3fffffff
-#define CFG_BANK7_ENABLE 0
+#define CONFIG_SYS_BANK0_START 0x00000000
+#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE/2 - 1)
+#define CONFIG_SYS_BANK0_ENABLE 1
+#define CONFIG_SYS_BANK1_START CONFIG_SYS_MAX_RAM_SIZE/2
+#define CONFIG_SYS_BANK1_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
+#define CONFIG_SYS_BANK1_ENABLE 1
+#define CONFIG_SYS_BANK2_START 0x3ff00000 /* not available in this design */
+#define CONFIG_SYS_BANK2_END 0x3fffffff
+#define CONFIG_SYS_BANK2_ENABLE 0
+#define CONFIG_SYS_BANK3_START 0x3ff00000
+#define CONFIG_SYS_BANK3_END 0x3fffffff
+#define CONFIG_SYS_BANK3_ENABLE 0
+#define CONFIG_SYS_BANK4_START 0x3ff00000
+#define CONFIG_SYS_BANK4_END 0x3fffffff
+#define CONFIG_SYS_BANK4_ENABLE 0
+#define CONFIG_SYS_BANK5_START 0x3ff00000
+#define CONFIG_SYS_BANK5_END 0x3fffffff
+#define CONFIG_SYS_BANK5_ENABLE 0
+#define CONFIG_SYS_BANK6_START 0x3ff00000
+#define CONFIG_SYS_BANK6_END 0x3fffffff
+#define CONFIG_SYS_BANK6_ENABLE 0
+#define CONFIG_SYS_BANK7_START 0x3ff00000
+#define CONFIG_SYS_BANK7_END 0x3fffffff
+#define CONFIG_SYS_BANK7_ENABLE 0
/*--------------------------------------------------------------------*/
/* 4.4 - Output Driver Control Register */
/*--------------------------------------------------------------------*/
-#define CFG_ODCR 0xe5
+#define CONFIG_SYS_ODCR 0xe5
/*--------------------------------------------------------------------*/
/* 4.8 - Error Handling Registers */
-/*-------------------------------CFG_SDMODE_BURSTLEN-------------------------------------*/
-#define CFG_ERRENR1 0x11 /* enable SDRAM refresh overflow error */
+/*-------------------------------CONFIG_SYS_SDMODE_BURSTLEN-------------------------------------*/
+#define CONFIG_SYS_ERRENR1 0x11 /* enable SDRAM refresh overflow error */
/* SDRAM 0-256 MB */
-#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-/*#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_CACHEINHIBIT) */
-#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+/*#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_CACHEINHIBIT) */
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
/* stack in dcache */
-#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_IBAT2L (CFG_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT2U (CFG_SDRAM_BASE + 0x10000000| BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_SDRAM_BASE + 0x10000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_SDRAM_BASE + 0x10000000| BATU_BL_256M | BATU_VS | BATU_VP)
/* PCI memory */
-/*#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) */
-/*#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) */
+/*#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) */
+/*#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) */
/*Flash, config addrs, etc. */
-#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT0L CFG_IBAT0L
-#define CFG_DBAT0U CFG_IBAT0U
-#define CFG_DBAT1L CFG_IBAT1L
-#define CFG_DBAT1U CFG_IBAT1U
-#define CFG_DBAT2L CFG_IBAT2L
-#define CFG_DBAT2U CFG_IBAT2U
-#define CFG_DBAT3L CFG_IBAT3L
-#define CFG_DBAT3U CFG_IBAT3U
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*----------------------------------------------------------------------*/
-#define CFG_FLASH_BASE 0xFF800000
-#define CFG_MAX_FLASH_BANKS 1 /* Max number of flash banks */
+#define CONFIG_SYS_FLASH_BASE 0xFF800000
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
/* NOTE: environment is not EMBEDDED in the u-boot code.
It's stored in flash in its own separate sector. */
#define CONFIG_ENV_IS_IN_FLASH 1
#if 1 /* AMD AM29LV033C */
-#define CFG_MAX_FLASH_SECT 64 /* Max number of sectors in one bank */
+#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors in one bank */
#define CONFIG_ENV_ADDR 0xFFBF0000 /* flash sector SA63 */
#define CONFIG_ENV_SECT_SIZE (64*1024) /* Size of the Environment Sector */
#else /* AMD AM29LV116D */
-#define CFG_MAX_FLASH_SECT 35 /* Max number of sectors in one bank */
+#define CONFIG_SYS_MAX_FLASH_SECT 35 /* Max number of sectors in one bank */
#define CONFIG_ENV_ADDR 0xFF9FA000 /* flash sector SA33 */
#define CONFIG_ENV_SECT_SIZE (8*1024) /* Size of the Environment Sector */
#endif /* #if */
@@ -407,22 +407,22 @@
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE /* Size of the Environment */
#define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
-#undef CFG_RAMBOOT
+#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
+#undef CONFIG_SYS_RAMBOOT
#else
-#define CFG_RAMBOOT
+#define CONFIG_SYS_RAMBOOT
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32
+#define CONFIG_SYS_CACHELINE_SIZE 32
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*