blob: c597f2db1e3586340e630254976f78f7badf8143 [file] [log] [blame]
/*
* (C) Copyright 2006 Aubrey.Li, aubrey.li@analog.com
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <asm/io.h>
#if defined(CONFIG_CMD_NAND)
#include <nand.h>
#define CONCAT(a,b,c,d) a ## b ## c ## d
#define PORT(a,b) CONCAT(pPORT,a,b,)
#ifndef CONFIG_NAND_GPIO_PORT
#define CONFIG_NAND_GPIO_PORT F
#endif
/*
* hardware specific access to control-lines
*/
static void bfin_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
register struct nand_chip *this = mtd->priv;
u32 IO_ADDR_W = (u32) this->IO_ADDR_W;
if (ctrl & NAND_CTRL_CHANGE) {
if( ctrl & NAND_CLE )
IO_ADDR_W = CONFIG_SYS_NAND_BASE + BFIN_NAND_CLE;
else
IO_ADDR_W = CONFIG_SYS_NAND_BASE;
if( ctrl & NAND_ALE )
IO_ADDR_W = CONFIG_SYS_NAND_BASE + BFIN_NAND_ALE;
else
IO_ADDR_W = CONFIG_SYS_NAND_BASE;
this->IO_ADDR_W = (void __iomem *) IO_ADDR_W;
}
this->IO_ADDR_R = this->IO_ADDR_W;
/* Drain the writebuffer */
SSYNC();
if (cmd != NAND_CMD_NONE)
writeb(cmd, this->IO_ADDR_W);
}
int bfin_device_ready(struct mtd_info *mtd)
{
int ret = (*PORT(CONFIG_NAND_GPIO_PORT, IO) & BFIN_NAND_READY) ? 1 : 0;
SSYNC();
return ret;
}
/*
* Board-specific NAND initialization. The following members of the
* argument are board-specific (per include/linux/mtd/nand.h):
* - IO_ADDR_R?: address to read the 8 I/O lines of the flash device
* - IO_ADDR_W?: address to write the 8 I/O lines of the flash device
* - cmd_ctrl: hardwarespecific function for accesing control-lines
* - dev_ready: hardwarespecific function for accesing device ready/busy line
* - enable_hwecc?: function to enable (reset) hardware ecc generator. Must
* only be provided if a hardware ECC is available
* - ecc.mode: mode of ecc, see defines
* - chip_delay: chip dependent delay for transfering data from array to
* read regs (tR)
* - options: various chip options. They can partly be set to inform
* nand_scan about special functionality. See the defines for further
* explanation
* Members with a "?" were not set in the merged testing-NAND branch,
* so they are not set here either.
*/
void board_nand_init(struct nand_chip *nand)
{
*PORT(CONFIG_NAND_GPIO_PORT, _FER) &= ~BFIN_NAND_READY;
*PORT(CONFIG_NAND_GPIO_PORT, IO_DIR) &= ~BFIN_NAND_READY;
*PORT(CONFIG_NAND_GPIO_PORT, IO_INEN) |= BFIN_NAND_READY;
nand->cmd_ctrl = bfin_hwcontrol;
nand->ecc.mode = NAND_ECC_SOFT;
nand->dev_ready = bfin_device_ready;
nand->chip_delay = 30;
}
#endif