blob: 1d8d08a847d9104356b3763248be95fd8beac2cf [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2017 Marek Behun <marek.behun@nic.cz>
* Copyright (C) 2016 Tomas Hlavacek <tomas.hlavacek@nic.cz>
*
* Derived from the code for
* Marvell/db-88f6820-gp by Stefan Roese <sr@denx.de>
*/
#include <common.h>
#include <env.h>
#include <i2c.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
#include <dm/uclass.h>
#include <fdt_support.h>
#include <time.h>
# include <atsha204a-i2c.h>
#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
#include <../serdes/a38x/high_speed_env_spec.h>
DECLARE_GLOBAL_DATA_PTR;
#define OMNIA_I2C_BUS_NAME "i2c@11000->i2cmux@70->i2c@0"
#define OMNIA_I2C_MCU_CHIP_ADDR 0x2a
#define OMNIA_I2C_MCU_CHIP_LEN 1
#define OMNIA_I2C_EEPROM_CHIP_ADDR 0x54
#define OMNIA_I2C_EEPROM_CHIP_LEN 2
#define OMNIA_I2C_EEPROM_MAGIC 0x0341a034
enum mcu_commands {
CMD_GET_STATUS_WORD = 0x01,
CMD_GET_RESET = 0x09,
CMD_WATCHDOG_STATE = 0x0b,
};
enum status_word_bits {
CARD_DET_STSBIT = 0x0010,
MSATA_IND_STSBIT = 0x0020,
};
#define OMNIA_ATSHA204_OTP_VERSION 0
#define OMNIA_ATSHA204_OTP_SERIAL 1
#define OMNIA_ATSHA204_OTP_MAC0 3
#define OMNIA_ATSHA204_OTP_MAC1 4
/*
* Those values and defines are taken from the Marvell U-Boot version
* "u-boot-2013.01-2014_T3.0"
*/
#define OMNIA_GPP_OUT_ENA_LOW \
(~(BIT(1) | BIT(4) | BIT(6) | BIT(7) | BIT(8) | BIT(9) | \
BIT(10) | BIT(11) | BIT(19) | BIT(22) | BIT(23) | BIT(25) | \
BIT(26) | BIT(27) | BIT(29) | BIT(30) | BIT(31)))
#define OMNIA_GPP_OUT_ENA_MID \
(~(BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(15) | \
BIT(16) | BIT(17) | BIT(18)))
#define OMNIA_GPP_OUT_VAL_LOW 0x0
#define OMNIA_GPP_OUT_VAL_MID 0x0
#define OMNIA_GPP_POL_LOW 0x0
#define OMNIA_GPP_POL_MID 0x0
static struct serdes_map board_serdes_map_pex[] = {
{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0}
};
static struct serdes_map board_serdes_map_sata[] = {
{SATA0, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0}
};
static struct udevice *omnia_get_i2c_chip(const char *name, uint addr,
uint offset_len)
{
struct udevice *bus, *dev;
int ret;
ret = uclass_get_device_by_name(UCLASS_I2C, OMNIA_I2C_BUS_NAME, &bus);
if (ret) {
printf("Cannot get I2C bus %s: uclass_get_device_by_name failed: %i\n",
OMNIA_I2C_BUS_NAME, ret);
return NULL;
}
ret = i2c_get_chip(bus, addr, offset_len, &dev);
if (ret) {
printf("Cannot get %s I2C chip: i2c_get_chip failed: %i\n",
name, ret);
return NULL;
}
return dev;
}
static int omnia_mcu_read(u8 cmd, void *buf, int len)
{
struct udevice *chip;
chip = omnia_get_i2c_chip("MCU", OMNIA_I2C_MCU_CHIP_ADDR,
OMNIA_I2C_MCU_CHIP_LEN);
if (!chip)
return -ENODEV;
return dm_i2c_read(chip, cmd, buf, len);
}
#ifndef CONFIG_SPL_BUILD
static int omnia_mcu_write(u8 cmd, const void *buf, int len)
{
struct udevice *chip;
chip = omnia_get_i2c_chip("MCU", OMNIA_I2C_MCU_CHIP_ADDR,
OMNIA_I2C_MCU_CHIP_LEN);
if (!chip)
return -ENODEV;
return dm_i2c_write(chip, cmd, buf, len);
}
static bool disable_mcu_watchdog(void)
{
int ret;
puts("Disabling MCU watchdog... ");
ret = omnia_mcu_write(CMD_WATCHDOG_STATE, "\x00", 1);
if (ret) {
printf("omnia_mcu_write failed: %i\n", ret);
return false;
}
puts("disabled\n");
return true;
}
#endif
static bool omnia_detect_sata(void)
{
int ret;
u16 stsword;
puts("MiniPCIe/mSATA card detection... ");
ret = omnia_mcu_read(CMD_GET_STATUS_WORD, &stsword, sizeof(stsword));
if (ret) {
printf("omnia_mcu_read failed: %i, defaulting to MiniPCIe card\n",
ret);
return false;
}
if (!(stsword & CARD_DET_STSBIT)) {
puts("none\n");
return false;
}
if (stsword & MSATA_IND_STSBIT)
puts("mSATA\n");
else
puts("MiniPCIe\n");
return stsword & MSATA_IND_STSBIT ? true : false;
}
int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
{
if (omnia_detect_sata()) {
*serdes_map_array = board_serdes_map_sata;
*count = ARRAY_SIZE(board_serdes_map_sata);
} else {
*serdes_map_array = board_serdes_map_pex;
*count = ARRAY_SIZE(board_serdes_map_pex);
}
return 0;
}
struct omnia_eeprom {
u32 magic;
u32 ramsize;
char region[4];
u32 crc;
};
static bool omnia_read_eeprom(struct omnia_eeprom *oep)
{
struct udevice *chip;
u32 crc;
int ret;
chip = omnia_get_i2c_chip("EEPROM", OMNIA_I2C_EEPROM_CHIP_ADDR,
OMNIA_I2C_EEPROM_CHIP_LEN);
if (!chip)
return false;
ret = dm_i2c_read(chip, 0, (void *)oep, sizeof(*oep));
if (ret) {
printf("dm_i2c_read failed: %i, cannot read EEPROM\n", ret);
return false;
}
if (oep->magic != OMNIA_I2C_EEPROM_MAGIC) {
printf("bad EEPROM magic number (%08x, should be %08x)\n",
oep->magic, OMNIA_I2C_EEPROM_MAGIC);
return false;
}
crc = crc32(0, (void *)oep, sizeof(*oep) - 4);
if (crc != oep->crc) {
printf("bad EEPROM CRC (stored %08x, computed %08x)\n",
oep->crc, crc);
return false;
}
return true;
}
static int omnia_get_ram_size_gb(void)
{
static int ram_size;
struct omnia_eeprom oep;
if (!ram_size) {
/* Get the board config from EEPROM */
if (omnia_read_eeprom(&oep)) {
debug("Memory config in EEPROM: 0x%02x\n", oep.ramsize);
if (oep.ramsize == 0x2)
ram_size = 2;
else
ram_size = 1;
} else {
/* Hardcoded fallback */
puts("Memory config from EEPROM read failed!\n");
puts("Falling back to default 1 GiB!\n");
ram_size = 1;
}
}
return ram_size;
}
/*
* Define the DDR layout / topology here in the board file. This will
* be used by the DDR3 init code in the SPL U-Boot version to configure
* the DDR3 controller.
*/
static struct mv_ddr_topology_map board_topology_map_1g = {
DEBUG_LEVEL_ERROR,
0x1, /* active interfaces */
/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
{ { { {0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0} },
SPEED_BIN_DDR_1600K, /* speed_bin */
MV_DDR_DEV_WIDTH_16BIT, /* memory_width */
MV_DDR_DIE_CAP_4GBIT, /* mem_size */
MV_DDR_FREQ_800, /* frequency */
0, 0, /* cas_wl cas_l */
MV_DDR_TEMP_NORMAL, /* temperature */
MV_DDR_TIM_2T} }, /* timing */
BUS_MASK_32BIT, /* Busses mask */
MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
{ {0} }, /* raw spd data */
{0} /* timing parameters */
};
static struct mv_ddr_topology_map board_topology_map_2g = {
DEBUG_LEVEL_ERROR,
0x1, /* active interfaces */
/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
{ { { {0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0},
{0x1, 0, 0, 0} },
SPEED_BIN_DDR_1600K, /* speed_bin */
MV_DDR_DEV_WIDTH_16BIT, /* memory_width */
MV_DDR_DIE_CAP_8GBIT, /* mem_size */
MV_DDR_FREQ_800, /* frequency */
0, 0, /* cas_wl cas_l */
MV_DDR_TEMP_NORMAL, /* temperature */
MV_DDR_TIM_2T} }, /* timing */
BUS_MASK_32BIT, /* Busses mask */
MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
{ {0} }, /* raw spd data */
{0} /* timing parameters */
};
struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
{
if (omnia_get_ram_size_gb() == 2)
return &board_topology_map_2g;
else
return &board_topology_map_1g;
}
#ifndef CONFIG_SPL_BUILD
static int set_regdomain(void)
{
struct omnia_eeprom oep;
char rd[3] = {' ', ' ', 0};
if (omnia_read_eeprom(&oep))
memcpy(rd, &oep.region, 2);
else
puts("EEPROM regdomain read failed.\n");
printf("Regdomain set to %s\n", rd);
return env_set("regdomain", rd);
}
/*
* default factory reset bootcommand on Omnia first sets all the front LEDs
* to green and then tries to load the rescue image from SPI flash memory and
* boot it
*/
#define OMNIA_FACTORY_RESET_BOOTCMD \
"i2c dev 2; " \
"i2c mw 0x2a.1 0x3 0x1c 1; " \
"i2c mw 0x2a.1 0x4 0x1c 1; " \
"mw.l 0x01000000 0x00ff000c; " \
"i2c write 0x01000000 0x2a.1 0x5 4 -s; " \
"setenv bootargs \"earlyprintk console=ttyS0,115200" \
" omniarescue=$omnia_reset\"; " \
"sf probe; " \
"sf read 0x1000000 0x100000 0x700000; " \
"bootm 0x1000000; " \
"bootz 0x1000000"
static void handle_reset_button(void)
{
int ret;
u8 reset_status;
ret = omnia_mcu_read(CMD_GET_RESET, &reset_status, 1);
if (ret) {
printf("omnia_mcu_read failed: %i, reset status unknown!\n",
ret);
return;
}
env_set_ulong("omnia_reset", reset_status);
if (reset_status) {
printf("RESET button was pressed, overwriting bootcmd!\n");
env_set("bootcmd", OMNIA_FACTORY_RESET_BOOTCMD);
}
}
#endif
int board_early_init_f(void)
{
/* Configure MPP */
writel(0x11111111, MVEBU_MPP_BASE + 0x00);
writel(0x11111111, MVEBU_MPP_BASE + 0x04);
writel(0x11244011, MVEBU_MPP_BASE + 0x08);
writel(0x22222111, MVEBU_MPP_BASE + 0x0c);
writel(0x22200002, MVEBU_MPP_BASE + 0x10);
writel(0x30042022, MVEBU_MPP_BASE + 0x14);
writel(0x55550555, MVEBU_MPP_BASE + 0x18);
writel(0x00005550, MVEBU_MPP_BASE + 0x1c);
/* Set GPP Out value */
writel(OMNIA_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
writel(OMNIA_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
/* Set GPP Polarity */
writel(OMNIA_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
writel(OMNIA_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
/* Set GPP Out Enable */
writel(OMNIA_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
writel(OMNIA_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
#ifndef CONFIG_SPL_BUILD
disable_mcu_watchdog();
#endif
return 0;
}
int board_late_init(void)
{
#ifndef CONFIG_SPL_BUILD
set_regdomain();
handle_reset_button();
#endif
pci_init();
return 0;
}
static struct udevice *get_atsha204a_dev(void)
{
static struct udevice *dev;
if (dev)
return dev;
if (uclass_get_device_by_name(UCLASS_MISC, "atsha204a@64", &dev)) {
puts("Cannot find ATSHA204A on I2C bus!\n");
dev = NULL;
}
return dev;
}
int checkboard(void)
{
u32 version_num, serial_num;
int err = 1;
struct udevice *dev = get_atsha204a_dev();
if (dev) {
err = atsha204a_wakeup(dev);
if (err)
goto out;
err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false,
OMNIA_ATSHA204_OTP_VERSION,
(u8 *)&version_num);
if (err)
goto out;
err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false,
OMNIA_ATSHA204_OTP_SERIAL,
(u8 *)&serial_num);
if (err)
goto out;
atsha204a_sleep(dev);
}
out:
printf("Turris Omnia:\n");
printf(" RAM size: %i MiB\n", omnia_get_ram_size_gb() * 1024);
if (err)
printf(" Serial Number: unknown\n");
else
printf(" Serial Number: %08X%08X\n", be32_to_cpu(version_num),
be32_to_cpu(serial_num));
return 0;
}
static void increment_mac(u8 *mac)
{
int i;
for (i = 5; i >= 3; i--) {
mac[i] += 1;
if (mac[i])
break;
}
}
int misc_init_r(void)
{
int err;
struct udevice *dev = get_atsha204a_dev();
u8 mac0[4], mac1[4], mac[6];
if (!dev)
goto out;
err = atsha204a_wakeup(dev);
if (err)
goto out;
err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false,
OMNIA_ATSHA204_OTP_MAC0, mac0);
if (err)
goto out;
err = atsha204a_read(dev, ATSHA204A_ZONE_OTP, false,
OMNIA_ATSHA204_OTP_MAC1, mac1);
if (err)
goto out;
atsha204a_sleep(dev);
mac[0] = mac0[1];
mac[1] = mac0[2];
mac[2] = mac0[3];
mac[3] = mac1[1];
mac[4] = mac1[2];
mac[5] = mac1[3];
if (is_valid_ethaddr(mac))
eth_env_set_enetaddr("eth1addr", mac);
increment_mac(mac);
if (is_valid_ethaddr(mac))
eth_env_set_enetaddr("eth2addr", mac);
increment_mac(mac);
if (is_valid_ethaddr(mac))
eth_env_set_enetaddr("ethaddr", mac);
out:
return 0;
}