blob: 39faf805806ee8be59eac2ce4e88340a1f734eb8 [file] [log] [blame]
/*
* (C) Copyright 2015 Linaro
*
* Peter Griffin <peter.griffin@linaro.org>
*
* Configuration for HiKey 96boards CE. Parts were derived from other ARM
* configurations.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __HIKEY_H
#define __HIKEY_H
#include <linux/sizes.h>
#define CONFIG_POWER
#define CONFIG_POWER_HI6553
#define CONFIG_REMAKE_ELF
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_BOARD_EARLY_INIT_F
/* Physical Memory Map */
/* CONFIG_SYS_TEXT_BASE needs to align with where ATF loads bl33.bin */
#define CONFIG_SYS_TEXT_BASE 0x35000000
#define CONFIG_NR_DRAM_BANKS 6
#define PHYS_SDRAM_1 0x00000000
/* 1008 MB (the last 16Mb are secured for TrustZone by ATF*/
#define PHYS_SDRAM_1_SIZE 0x3EFFFFFF
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x80000)
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 19000000
/* Generic Interrupt Controller Definitions */
#define GICD_BASE 0xf6801000
#define GICC_BASE 0xf6802000
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_8M)
/* Serial port PL010/PL011 through the device model */
#define CONFIG_PL01X_SERIAL
#define CONFIG_BAUDRATE 115200
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_DWC2
#define CONFIG_USB_DWC2_REG_ADDR 0xF72C0000
/*#define CONFIG_DWC2_DFLT_SPEED_FULL*/
#define CONFIG_DWC2_ENABLE_DYNAMIC_FIFO
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_MISC_INIT_R
#endif
#define CONFIG_HIKEY_GPIO
/* SD/MMC configuration */
#define CONFIG_GENERIC_MMC
#define CONFIG_MMC
#define CONFIG_DWMMC
#define CONFIG_HIKEY_DWMMC
#define CONFIG_BOUNCE_BUFFER
#define CONFIG_FS_EXT4
/* Command line configuration */
#define CONFIG_MENU
#define CONFIG_CMD_UNZIP
#define CONFIG_CMD_ENV
#define CONFIG_MTD_PARTITIONS
/* BOOTP options */
#define CONFIG_BOOTP_BOOTFILESIZE
#include <config_distro_defaults.h>
/* Initial environment variables */
/*
* Defines where the kernel and FDT will be put in RAM
*/
/* Assume we boot with root on the seventh partition of eMMC */
#define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 root=/dev/mmcblk0p9 rw"
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 1) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
"kernel_name=Image\0" \
"kernel_addr_r=0x00080000\0" \
"fdtfile=hi6220-hikey.dtb\0" \
"fdt_addr_r=0x02000000\0" \
"fdt_high=0xffffffffffffffff\0" \
"initrd_high=0xffffffffffffffff\0" \
BOOTENV
/* Preserve environment on sd card */
#define CONFIG_COMMAND_HISTORY
#define CONFIG_ENV_SIZE 0x1000
#define CONFIG_ENV_IS_IN_FAT
#define FAT_ENV_INTERFACE "mmc"
#define FAT_ENV_DEVICE_AND_PART "1:1"
#define FAT_ENV_FILE "uboot.env"
#define CONFIG_FAT_WRITE
#define CONFIG_ENV_VARS_UBOOT_CONFIG
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_SYS_NO_FLASH
#endif /* __HIKEY_H */