blob: 76c739776ac18389df11fa44cc31e7764f358ff9 [file] [log] [blame]
/*
* Configuration settings for the mini-box PICOSAM9G45 board.
* (C) Copyright 2015 Inter Act B.V.
*
* Based on:
* U-Boot file: include/configs/at91sam9m10g45ek.h
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/hardware.h>
#define CONFIG_SYS_TEXT_BASE 0x23f00000
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
#define CONFIG_PICOSAM
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#define CONFIG_AT91_GPIO
#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
/* LCD */
#define CONFIG_LCD
#define LCD_BPP LCD_COLOR8
#define CONFIG_LCD_LOGO
#undef LCD_TEST_PATTERN
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_SYS_WHITE_ON_BLACK
#define CONFIG_ATMEL_LCD
#define CONFIG_ATMEL_LCD_RGB565
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
/* board specific(not enough SRAM) */
#define CONFIG_AT91SAM9G45_LCD_BASE 0x23E00000
/* LED */
#define CONFIG_AT91_LED
#define CONFIG_GREEN_LED AT91_PIN_PD31 /* this is the user1 led */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/* Enable the watchdog */
#define CONFIG_AT91SAM9_WATCHDOG
#define CONFIG_HW_WATCHDOG
/*
* Command line configuration.
*/
/* No NOR flash */
#define CONFIG_SYS_NO_FLASH
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 2
#define PHYS_SDRAM_1 ATMEL_BASE_CS1 /* on DDRSDRC1 */
#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
#define PHYS_SDRAM_2 ATMEL_BASE_CS6 /* on DDRSDRC0 */
#define PHYS_SDRAM_2_SIZE 0x08000000 /* 128 MB */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
/* MMC */
#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#endif
#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_DOS_PARTITION
#endif
/* Ethernet */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R
#define CONFIG_AT91_WANTS_COMMON_PHY
/* USB */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x23e00000
#ifdef CONFIG_SYS_USE_MMC
/* bootstrap + u-boot + env + linux in mmc */
#define FAT_ENV_INTERFACE "mmc"
/*
* We don't specify the part number, if device 0 has partition table, it means
* the first partition; it no partition table, then take whole device as a
* FAT file system.
*/
#define FAT_ENV_DEVICE_AND_PART "0"
#define FAT_ENV_FILE "uboot.env"
#define CONFIG_ENV_IS_IN_FAT
#define CONFIG_FAT_WRITE
#define CONFIG_ENV_SIZE 0x4000
#define CONFIG_BOOTARGS "console=ttyS0,115200 " \
"root=/dev/mmcblk0p2 rw rootwait"
#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 dtb; " \
"fatload mmc 0:1 0x22000000 zImage; " \
"bootz 0x22000000 - 0x21000000"
#endif
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x300000
#define CONFIG_SPL_MAX_SIZE 0x010000
#define CONFIG_SPL_STACK 0x310000
#define CONFIG_SYS_MONITOR_LEN 0x80000
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_SPL_ATMEL_SIZE
#define CONFIG_SYS_MASTER_CLOCK 132096000
#define CONFIG_SYS_AT91_PLLA 0x20c73f03
#define CONFIG_SYS_MCKR 0x1301
#define CONFIG_SYS_MCKR_CSS 0x1302
#endif
#endif