blob: ad5fa53160043b74a68e8f3d194405fbe03eb132 [file] [log] [blame]
/*
* U-boot - Configuration file for BF526 EZBrd board
*/
#ifndef __CONFIG_BF526_EZBRD_H__
#define __CONFIG_BF526_EZBRD_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf526-0.0
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 25000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 16
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
/*
* Memory Settings
*/
/* This board has a 64meg MT48H32M16 */
#define CONFIG_MEM_ADD_WDTH 10
#define CONFIG_MEM_SIZE 64
#define CONFIG_EBIU_SDRRC_VAL 0x0267
#define CONFIG_EBIU_SDGCTL_VAL (SCTLE | CL_2 | PASR_ALL | TRAS_6 | TRP_4 | TRCD_2 | TWR_2 | PSS)
#define CONFIG_EBIU_AMGCTL_VAL (AMCKEN | AMBEN_ALL)
#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_15 | B1RAT_15 | B1HT_3 | B1RDYPOL | B0WAT_15 | B0RAT_15 | B0HT_3 | B0RDYPOL)
#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_15 | B3RAT_15 | B3HT_3 | B3RDYPOL | B2WAT_15 | B2RAT_15 | B2HT_3 | B2RDYPOL)
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
/*
* NAND Settings
* (can't be used same time as ethernet)
*/
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
# define CONFIG_BFIN_NFC
# define CONFIG_BFIN_NFC_BOOTROM_ECC
#endif
#ifdef CONFIG_BFIN_NFC
#define CONFIG_BFIN_NFC_CTL_VAL 0x0033
#define CONFIG_DRIVER_NAND_BFIN
#define CONFIG_SYS_NAND_BASE 0 /* not actually used */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_CMD_NAND
#endif
/*
* Network Settings
*/
#if !defined(__ADSPBF522__) && !defined(__ADSPBF523__) && \
!defined(__ADSPBF524__) && !defined(__ADSPBF525__) && !defined(CONFIG_BFIN_NFC)
#define ADI_CMDS_NETWORK 1
#define CONFIG_BFIN_MAC
#define CONFIG_RMII
#define CONFIG_NETCONSOLE 1
#endif
#define CONFIG_HOSTNAME bf526-ezbrd
#define CONFIG_LIB_RAND
/*
* Flash Settings
*/
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 71
/*
* SPI Settings
*/
#define CONFIG_BFIN_SPI
#define CONFIG_ENV_SPI_MAX_HZ 30000000
#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SST
/*
* Env Storage Settings
*/
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET 0x4000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_OFFSET 0x4000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x2000
#endif
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
/*
* I2C Settings
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_ADI
/*
* USB Settings
*/
#if !defined(__ADSPBF522__) && !defined(__ADSPBF523__)
#define CONFIG_USB
#define CONFIG_MUSB_HCD
#define CONFIG_USB_BLACKFIN
#define CONFIG_USB_STORAGE
#define CONFIG_MUSB_TIMEOUT 100000
#endif
/*
* Misc Settings
*/
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 1
/* define to enable run status via led */
/* #define CONFIG_STATUS_LED */
#ifdef CONFIG_STATUS_LED
#define CONFIG_GPIO_LED
#define CONFIG_BOARD_SPECIFIC_LED
/* use LED0 to indicate booting/alive */
#define STATUS_LED_BOOT 0
#define STATUS_LED_BIT GPIO_PF8
#define STATUS_LED_STATE STATUS_LED_ON
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
/* use LED1 to indicate crash */
#define STATUS_LED_CRASH 1
#define STATUS_LED_BIT1 GPIO_PG11
#define STATUS_LED_STATE1 STATUS_LED_ON
#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
/* #define STATUS_LED_BIT2 GPIO_PG12 */
#endif
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif