Update for NC650 board. Add NC650 based CP850 configuration.
Signed-off-by: dzu@denx.de <dzu@denx.de>
diff --git a/include/configs/NC650.h b/include/configs/NC650.h
index 3c59df4..8da29c4 100644
--- a/include/configs/NC650.h
+++ b/include/configs/NC650.h
@@ -1,4 +1,5 @@
/*
+ * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
* (C) Copyright 2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
@@ -65,6 +66,11 @@
#define CFG_8XX_XIN CONFIG_8xx_OSCLK
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d seconds...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "ids"
+#define CONFIG_BOOT_RETRY_TIME 900
+#define CONFIG_BOOT_RETRY_MIN 30
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
@@ -75,7 +81,7 @@
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
"bootm"
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#define CONFIG_WATCHDOG /* watchdog enabled */
#undef CONFIG_STATUS_LED /* Status LED disabled */
@@ -96,12 +102,26 @@
/*
* Software (bit-bang) I2C driver configuration
*/
+#if defined(CONFIG_IDS852_REV1)
+
#define SCL 0x1000 /* PA 3 */
#define SDA 0x2000 /* PA 2 */
#define __I2C_DIR immr->im_ioport.iop_padir
#define __I2C_DAT immr->im_ioport.iop_padat
#define __I2C_PAR immr->im_ioport.iop_papar
+
+#elif defined(CONFIG_IDS852_REV2)
+
+#define SCL 0x0002 /* PB 30 */
+#define SDA 0x0001 /* PB 31 */
+
+#define __I2C_PAR immr->im_cpm.cp_pbpar
+#define __I2C_DIR immr->im_cpm.cp_pbdir
+#define __I2C_DAT immr->im_cpm.cp_pbdat
+
+#endif
+
#define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \
__I2C_DIR |= (SDA|SCL); }
#define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0)
@@ -229,17 +249,6 @@
#define ADDR_COLUMN 1
#define NAND_NO_RB
-#define NAND_WAIT_READY(nand) udelay(12)
-#define WRITE_NAND_COMMAND(d, adr) WRITE_NAND(d, adr + 2)
-#define WRITE_NAND_ADDRESS(d, adr) WRITE_NAND(d, adr + 1)
-#define WRITE_NAND(d, adr) (*(volatile uint8_t *)(adr) = (uint8_t)(d))
-#define READ_NAND(adr) (*(volatile uint8_t *)(adr))
-#define NAND_DISABLE_CE(nand) /* nop */
-#define NAND_ENABLE_CE(nand) /* nop */
-#define NAND_CTL_CLRALE(nandptr) /* nop */
-#define NAND_CTL_SETALE(nandptr) /* nop */
-#define NAND_CTL_CLRCLE(nandptr) /* nop */
-#define NAND_CTL_SETCLE(nandptr) /* nop */
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
@@ -312,7 +321,8 @@
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
/*
- * BR2 and OR2 (NAND Flash) - now addressed through UPMB
+ * BR2 and OR2 (NAND Flash) - addressed through UPMB on rev 1
+ * rev2 only uses the chipselect
*/
#define CFG_NAND_BASE 0x50000000
#define CFG_NAND_SIZE 0x04000000
@@ -338,6 +348,18 @@
#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
/*
+ * BR4 and OR4 (CPLD)
+ */
+#define CFG_CPLD_BASE 0x80000000 /* CPLD */
+#define CFG_CPLD_SIZE 0x10000 /* only 16 used */
+
+#define CFG_OR_TIMING_CPLD (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
+ OR_SCY_1_CLK)
+
+#define CFG_BR4_PRELIM ((CFG_CPLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+#define CFG_OR4_PRELIM (((-CFG_CPLD_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_CPLD)
+
+/*
* BR5 and OR5 (SRAM)
*/
#define CFG_SRAM_BASE 0x60000000
@@ -349,6 +371,16 @@
#define CFG_BR5_PRELIM ((CFG_SRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
#define CFG_OR5_PRELIM (((-CFG_SRAM_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_SRAM)
+#if defined(CONFIG_CP850)
+/*
+ * BR6 and OR6 (DPRAM) - only on CP850
+ */
+#define CFG_OR6_PRELIM 0xffff8170
+#define CFG_BR6_PRELIM 0xa0000401
+#define DPRAM_BASE_ADDR 0xa0000000
+
+#define CONFIG_MISC_INIT_R 1
+#endif
/*
* 4096 Rows from SDRAM example configuration
@@ -413,14 +445,12 @@
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
-/*
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT "nor0=nc650-0,nand0=nc650-nand"
#define MTDPARTS_DEFAULT "mtdparts=nc650-0:1m(kernel1),1m(kernel2)," \
- "2560k(cramfs1),2560k(cramfs2)," \
- "256k(u-boot),256k(env);" \
- "nc650-nand:4m(nand1),28m(nand2)"
-*/
+ "4m(cramfs1),1m(cramfs2)," \
+ "256k(u-boot),128k(env);" \
+ "nc650-nand:4m(jffs1),28m(jffs2)"
#endif /* __CONFIG_H */