blob: dacd2a911fe2829787c964b7243b46992f529381 [file] [log] [blame]
/*
* Copyright 2007 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#include <common.h>
#include <command.h>
#include <pci.h>
#include <asm/processor.h>
#include <asm/immap_86xx.h>
#include <asm/immap_fsl_pci.h>
#include <asm/fsl_ddr_sdram.h>
#include <i2c.h>
#include <asm/io.h>
#include <libfdt.h>
#include <fdt_support.h>
#include <spd_sdram.h>
#include <netdev.h>
#include "../common/pixis.h"
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif
void sdram_init(void);
long int fixed_sdram(void);
void mpc8610hpcd_diu_init(void);
/* called before any console output */
int board_early_init_f(void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_gur_t *gur = &immap->im_gur;
gur->gpiocr |= 0x88aa5500; /* DIU16, IR1, UART0, UART2 */
return 0;
}
int misc_init_r(void)
{
u8 tmp_val, version;
/*Do not use 8259PIC*/
tmp_val = in8(PIXIS_BASE + PIXIS_BRDCFG0);
out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val | 0x80);
/*For FPGA V7 or higher, set the IRQMAPSEL to 0 to use MAP0 interrupt*/
version = in8(PIXIS_BASE + PIXIS_PVER);
if(version >= 0x07) {
tmp_val = in8(PIXIS_BASE + PIXIS_BRDCFG0);
out8(PIXIS_BASE + PIXIS_BRDCFG0, tmp_val & 0xbf);
}
/* Using this for DIU init before the driver in linux takes over
* Enable the TFP410 Encoder (I2C address 0x38)
*/
tmp_val = 0xBF;
i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
/* Verify if enabled */
tmp_val = 0;
i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
debug("DVI Encoder Read: 0x%02lx\n",tmp_val);
tmp_val = 0x10;
i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
/* Verify if enabled */
tmp_val = 0;
i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
debug("DVI Encoder Read: 0x%02lx\n",tmp_val);
#ifdef CONFIG_FSL_DIU_FB
mpc8610hpcd_diu_init();
#endif
return 0;
}
int checkboard(void)
{
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_local_mcm_t *mcm = &immap->im_local_mcm;
printf ("Board: MPC8610HPCD, System ID: 0x%02x, "
"System Version: 0x%02x, FPGA Version: 0x%02x\n",
in8(PIXIS_BASE + PIXIS_ID), in8(PIXIS_BASE + PIXIS_VER),
in8(PIXIS_BASE + PIXIS_PVER));
mcm->abcr |= 0x00010000; /* 0 */
mcm->hpmr3 = 0x80000008; /* 4c */
mcm->hpmr0 = 0;
mcm->hpmr1 = 0;
mcm->hpmr2 = 0;
mcm->hpmr4 = 0;
mcm->hpmr5 = 0;
return 0;
}
phys_size_t
initdram(int board_type)
{
long dram_size = 0;
#if defined(CONFIG_SPD_EEPROM)
dram_size = fsl_ddr_sdram();
#else
dram_size = fixed_sdram();
#endif
#if defined(CONFIG_SYS_RAMBOOT)
puts(" DDR: ");
return dram_size;
#endif
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize and enable DDR ECC.
*/
ddr_enable_ecc(dram_size);
#endif
puts(" DDR: ");
return dram_size;
}
#if !defined(CONFIG_SPD_EEPROM)
/*
* Fixed sdram init -- doesn't use serial presence detect.
*/
long int fixed_sdram(void)
{
#if !defined(CONFIG_SYS_RAMBOOT)
volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
volatile ccsr_ddr_t *ddr = &immap->im_ddr1;
uint d_init;
ddr->cs0_bnds = 0x0000001f;
ddr->cs0_config = 0x80010202;
ddr->timing_cfg_3 = 0x00000000;
ddr->timing_cfg_0 = 0x00260802;
ddr->timing_cfg_1 = 0x3935d322;
ddr->timing_cfg_2 = 0x14904cc8;
ddr->sdram_mode_1 = 0x00480432;
ddr->sdram_mode_2 = 0x00000000;
ddr->sdram_interval = 0x06180fff; /* 0x06180100; */
ddr->sdram_data_init = 0xDEADBEEF;
ddr->sdram_clk_cntl = 0x03800000;
ddr->sdram_cfg_2 = 0x04400010;
#if defined(CONFIG_DDR_ECC)
ddr->err_int_en = 0x0000000d;
ddr->err_disable = 0x00000000;
ddr->err_sbe = 0x00010000;
#endif
asm("sync;isync");
udelay(500);
ddr->sdram_cfg_1 = 0xc3000000; /* 0xe3008000;*/
#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
d_init = 1;
debug("DDR - 1st controller: memory initializing\n");
/*
* Poll until memory is initialized.
* 512 Meg at 400 might hit this 200 times or so.
*/
while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0)
udelay(1000);
debug("DDR: memory initialized\n\n");
asm("sync; isync");
udelay(500);
#endif
return 512 * 1024 * 1024;
#endif
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
}
#endif
#if defined(CONFIG_PCI)
/*
* Initialize PCI Devices, report devices found.
*/
#ifndef CONFIG_PCI_PNP
static struct pci_config_table pci_fsl86xxads_config_table[] = {
{PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
PCI_IDSEL_NUMBER, PCI_ANY_ID,
pci_cfgfunc_config_device, {PCI_ENET0_IOADDR,
PCI_ENET0_MEMADDR,
PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER} },
{}
};
#endif
static struct pci_controller pci1_hose = {
#ifndef CONFIG_PCI_PNP
config_table:pci_mpc86xxcts_config_table
#endif
};
#endif /* CONFIG_PCI */
#ifdef CONFIG_PCIE1
static struct pci_controller pcie1_hose;
#endif
#ifdef CONFIG_PCIE2
static struct pci_controller pcie2_hose;
#endif
int first_free_busno = 0;
extern int fsl_pci_setup_inbound_windows(struct pci_region *r);
extern void fsl_pci_init(struct pci_controller *hose);
void pci_init_board(void)
{
volatile immap_t *immap = (immap_t *) CONFIG_SYS_CCSRBAR;
volatile ccsr_gur_t *gur = &immap->im_gur;
uint devdisr = gur->devdisr;
uint io_sel = (gur->pordevsr & MPC8610_PORDEVSR_IO_SEL)
>> MPC8610_PORDEVSR_IO_SEL_SHIFT;
uint host_agent = (gur->porbmsr & MPC8610_PORBMSR_HA)
>> MPC8610_PORBMSR_HA_SHIFT;
printf( " pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n",
devdisr, io_sel, host_agent);
#ifdef CONFIG_PCIE1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
struct pci_controller *hose = &pcie1_hose;
int pcie_configured = (io_sel == 1) || (io_sel == 4);
int pcie_ep = (host_agent == 0) || (host_agent == 2) ||
(host_agent == 5);
struct pci_region *r = hose->regions;
if (pcie_configured && !(devdisr & MPC86xx_DEVDISR_PCIE1)) {
printf(" PCIe 1 connected to Uli as %s (base address %x)\n",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det)
pci->pme_msg_det = 0xffffffff;
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE1_MEM_BASE,
CONFIG_SYS_PCIE1_MEM_PHYS,
CONFIG_SYS_PCIE1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE1_IO_BASE,
CONFIG_SYS_PCIE1_IO_PHYS,
CONFIG_SYS_PCIE1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
pci_setup_indirect(hose, (int)&pci->cfg_addr,
(int)&pci->cfg_data);
fsl_pci_init(hose);
first_free_busno = hose->last_busno + 1;
printf(" PCI-Express 1 on bus %02x - %02x\n",
hose->first_busno, hose->last_busno);
} else
puts(" PCI-Express 1: Disabled\n");
}
#else
puts("PCI-Express 1: Disabled\n");
#endif /* CONFIG_PCIE1 */
#ifdef CONFIG_PCIE2
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR;
struct pci_controller *hose = &pcie2_hose;
struct pci_region *r = hose->regions;
int pcie_configured = (io_sel == 0) || (io_sel == 4);
int pcie_ep = (host_agent == 0) || (host_agent == 1) ||
(host_agent == 4);
if (pcie_configured && !(devdisr & MPC86xx_DEVDISR_PCIE2)) {
printf(" PCI-Express 2 connected to slot as %s" \
" (base address %x)\n",
pcie_ep ? "End Point" : "Root Complex",
(uint)pci);
if (pci->pme_msg_det)
pci->pme_msg_det = 0xffffffff;
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCIE2_MEM_BASE,
CONFIG_SYS_PCIE2_MEM_PHYS,
CONFIG_SYS_PCIE2_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCIE2_IO_BASE,
CONFIG_SYS_PCIE2_IO_PHYS,
CONFIG_SYS_PCIE2_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
pci_setup_indirect(hose, (int)&pci->cfg_addr,
(int)&pci->cfg_data);
fsl_pci_init(hose);
first_free_busno = hose->last_busno + 1;
printf(" PCI-Express 2 on bus %02x - %02x\n",
hose->first_busno, hose->last_busno);
} else
puts(" PCI-Express 2: Disabled\n");
}
#else
puts("PCI-Express 2: Disabled\n");
#endif /* CONFIG_PCIE2 */
#ifdef CONFIG_PCI1
{
volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
struct pci_controller *hose = &pci1_hose;
int pci_agent = (host_agent >= 4) && (host_agent <= 6);
struct pci_region *r = hose->regions;
if ( !(devdisr & MPC86xx_DEVDISR_PCI1)) {
printf(" PCI connected to PCI slots as %s" \
" (base address %x)\n",
pci_agent ? "Agent" : "Host",
(uint)pci);
/* inbound */
r += fsl_pci_setup_inbound_windows(r);
/* outbound memory */
pci_set_region(r++,
CONFIG_SYS_PCI1_MEM_BASE,
CONFIG_SYS_PCI1_MEM_PHYS,
CONFIG_SYS_PCI1_MEM_SIZE,
PCI_REGION_MEM);
/* outbound io */
pci_set_region(r++,
CONFIG_SYS_PCI1_IO_BASE,
CONFIG_SYS_PCI1_IO_PHYS,
CONFIG_SYS_PCI1_IO_SIZE,
PCI_REGION_IO);
hose->region_count = r - hose->regions;
hose->first_busno = first_free_busno;
pci_setup_indirect(hose, (int) &pci->cfg_addr,
(int) &pci->cfg_data);
fsl_pci_init(hose);
first_free_busno = hose->last_busno + 1;
printf(" PCI on bus %02x - %02x\n",
hose->first_busno, hose->last_busno);
} else
puts(" PCI: Disabled\n");
}
#endif /* CONFIG_PCI1 */
}
#if defined(CONFIG_OF_BOARD_SETUP)
extern void ft_fsl_pci_setup(void *blob, const char *pci_alias,
struct pci_controller *hose);
void
ft_board_setup(void *blob, bd_t *bd)
{
do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
"timebase-frequency", bd->bi_busfreq / 4, 1);
do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
"bus-frequency", bd->bi_busfreq, 1);
do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
"clock-frequency", bd->bi_intfreq, 1);
do_fixup_by_prop_u32(blob, "device_type", "soc", 4,
"bus-frequency", bd->bi_busfreq, 1);
do_fixup_by_compat_u32(blob, "ns16550",
"clock-frequency", bd->bi_busfreq, 1);
fdt_fixup_memory(blob, bd->bi_memstart, bd->bi_memsize);
#ifdef CONFIG_PCI1
ft_fsl_pci_setup(blob, "pci0", &pci1_hose);
#endif
#ifdef CONFIG_PCIE1
ft_fsl_pci_setup(blob, "pci1", &pcie1_hose);
#endif
#ifdef CONFIG_PCIE2
ft_fsl_pci_setup(blob, "pci2", &pcie2_hose);
#endif
}
#endif
/*
* get_board_sys_clk
* Reads the FPGA on board for CONFIG_SYS_CLK_FREQ
*/
unsigned long
get_board_sys_clk(ulong dummy)
{
u8 i;
ulong val = 0;
ulong a;
a = PIXIS_BASE + PIXIS_SPD;
i = in8(a);
i &= 0x07;
switch (i) {
case 0:
val = 33333000;
break;
case 1:
val = 39999600;
break;
case 2:
val = 49999500;
break;
case 3:
val = 66666000;
break;
case 4:
val = 83332500;
break;
case 5:
val = 99999000;
break;
case 6:
val = 133332000;
break;
case 7:
val = 166665000;
break;
}
return val;
}
int board_eth_init(bd_t *bis)
{
return pci_eth_init(bis);
}