blob: 8a400298096e6099333eb62bfcd125e167fc2431 [file] [log] [blame]
/*
* Copyright (C) 2007 Freescale Semiconductor, Inc.
*
* Copyright (C) 2011 Matrix Vision GmbH
* Andre Schwarz <andre.schwarz@matrix-vision.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <version.h>
/*
* High Level Configuration Options
*/
#define CONFIG_E300 1
#define CONFIG_MPC83xx 1
#define CONFIG_MPC837x 1
#define CONFIG_MPC8377 1
#define CONFIG_SYS_TEXT_BASE 0xFC000000
#define CONFIG_PCI 1
#define CONFIG_PCI_INDIRECT_BRIDGE 1
#define CONFIG_MASK_AER_AO
#define CONFIG_DISPLAY_AER_FULL
#define CONFIG_MISC_INIT_R
/*
* On-board devices
*/
#define CONFIG_TSEC_ENET
/*
* System Clock Setup
*/
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
#define CONFIG_PCIE
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES
#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
/*
* Hardware Reset Configuration Word stored in EEPROM.
*/
#define CONFIG_SYS_HRCW_LOW 0
#define CONFIG_SYS_HRCW_HIGH 0
/* Arbiter Configuration Register */
#define CONFIG_SYS_ACR_PIPE_DEP 3
#define CONFIG_SYS_ACR_RPTCNT 3
/* System Priority Control Regsiter */
#define CONFIG_SYS_SPCR_TSECEP 3
/* System Clock Configuration Register */
#define CONFIG_SYS_SCCR_TSEC1CM 3
#define CONFIG_SYS_SCCR_TSEC2CM 0
#define CONFIG_SYS_SCCR_SDHCCM 3
#define CONFIG_SYS_SCCR_ENCCM 3 /* also clock for I2C-1 */
#define CONFIG_SYS_SCCR_USBDRCM CONFIG_SYS_SCCR_ENCCM /* must match */
#define CONFIG_SYS_SCCR_PCIEXP1CM 3
#define CONFIG_SYS_SCCR_PCIEXP2CM 3
#define CONFIG_SYS_SCCR_PCICM 1
#define CONFIG_SYS_SCCR_SATACM 0xFF
/*
* System IO Config
*/
#define CONFIG_SYS_SICRH 0x087c0000
#define CONFIG_SYS_SICRL 0x40000000
/*
* Output Buffer Impedance
*/
#define CONFIG_SYS_OBIR 0x30000000
/*
* IMMR new address
*/
#define CONFIG_SYS_IMMR 0xE0000000
/*
* DDR Setup
*/
#define CONFIG_SYS_DDR_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_83XX_DDR_USES_CS0
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN | DDRCDR_PZ_HIZ |\
DDRCDR_NZ_HIZ | DDRCDR_ODT |\
DDRCDR_Q_DRN)
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
#define CONFIG_SYS_DDR_MODE_WEAK
#define CONFIG_SYS_DDR_WRITE_DATA_DELAY 2
#define CONFIG_SYS_DDR_CPO 0x1f
/* SPD table located at offset 0x20 in extended adressing ROM
* used for HRCW fetch after power-on reset
*/
#define CONFIG_SPD_EEPROM
#define SPD_EEPROM_ADDRESS 0x50
#define SPD_EEPROM_OFFSET 0x20
#define SPD_EEPROM_ADDR_LEN 2
/*
* The reserved memory
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (512*1024)
#define CONFIG_SYS_MALLOC_LEN (512*1024)
/*
* Initial RAM Base Address Setup
*/
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\
CONFIG_SYS_GBL_DATA_SIZE)
/*
* Local Bus Configuration & Clock Setup
*/
#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_FSL_ELBC 1
/*
* FLASH on the Local Bus
*/
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_FLASH_SIZE 64
#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB)
#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 |\
BR_MS_GPCM | BR_V)
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_FLASH_BASE | OR_UPM_XAM |\
OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 |\
OR_GPCM_XACS | OR_GPCM_SCY_15 |\
OR_GPCM_TRLX_SET | OR_GPCM_EHTR_SET |\
OR_GPCM_EAD)
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 512
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
/*
* NAND Flash on the Local Bus
*/
#define CONFIG_MTD_NAND_VERIFY_WRITE 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_NAND_FSL_ELBC 1
#define CONFIG_SYS_NAND_BASE 0xE0600000
#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE | BR_DECC_CHK_GEN |\
BR_PS_8 | BR_MS_FCM | BR_V)
#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_FCM_BCTLD | OR_FCM_CST |\
OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_RST |\
OR_FCM_TRLX | OR_FCM_EHTR)
#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB)
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
#define CONFIG_CONSOLE ttyS0
#define CONFIG_BAUDRATE 115200
/* SERDES */
#define CONFIG_FSL_SERDES
#define CONFIG_FSL_SERDES1 0xe3000
#define CONFIG_FSL_SERDES2 0xe3100
/* Use the HUSH parser */
#define CONFIG_SYS_HUSH_PARSER
/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 400000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
/*
* General PCI
* Addresses are mapped 1-1.
*/
#define CONFIG_SYS_PCI_MEM_BASE 0x80000000
#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE
#define CONFIG_SYS_PCI_MEM_SIZE (256 << 20)
#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000
#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE
#define CONFIG_SYS_PCI_MMIO_SIZE (256 << 20)
#define CONFIG_SYS_PCI_IO_BASE 0x00000000
#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000
#define CONFIG_SYS_PCI_IO_SIZE (1 << 20)
#ifdef CONFIG_PCIE
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
#define CONFIG_SYS_PCIE1_CFG_SIZE (128 << 20)
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
#define CONFIG_SYS_PCIE1_MEM_SIZE (256 << 20)
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
#define CONFIG_SYS_PCIE1_IO_SIZE (8 << 20)
#define CONFIG_SYS_PCIE2_BASE 0xC0000000
#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
#define CONFIG_SYS_PCIE2_CFG_SIZE (128 << 20)
#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
#define CONFIG_SYS_PCIE2_MEM_SIZE (256 << 20)
#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
#define CONFIG_SYS_PCIE2_IO_SIZE (8 << 20)
#endif
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
/*
* TSEC
*/
#define CONFIG_GMII /* MII PHY management */
#define CONFIG_SYS_VSC8601_SKEWFIX
#define CONFIG_SYS_VSC8601_SKEW_TX 3
#define CONFIG_SYS_VSC8601_SKEW_RX 3
#define CONFIG_TSEC1
#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 0x10
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_HAS_ETH0
/*
* SATA
*/
#define CONFIG_LIBATA
#define CONFIG_FSL_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1_OFFSET 0x18000
#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2_OFFSET 0x19000
#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
#define CONFIG_LBA48
#define CONFIG_CMD_SATA
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_EXT2
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_VENDOREX
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_NTPSERVER
#define CONFIG_BOOTP_RANDOM_DELAY
#define CONFIG_BOOTP_SEND_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PING
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PCI
#define CONFIG_CMD_USB
#define CONFIG_CMD_SPI
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_SATA
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_JFFS2
#define CONFIG_RBTREE
#define CONFIG_LZO
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=NOR,nand0=NAND"
#define MTDPARTS_DEFAULT "mtdparts=NOR:1M(u-boot),2M(FPGA);NAND:-(root)"
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE 1
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_AUTO_COMPLETE
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_LOAD_ADDR 0x2000000
#define CONFIG_LOADADDR 0x4000000
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_LOADS_ECHO 1
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1
#define CONFIG_SYS_MEMTEST_START (60<<20)
#define CONFIG_SYS_MEMTEST_END (70<<20)
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
/*
* Core HID Setup
*/
#define CONFIG_SYS_HID0_INIT 0x000000000
#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2 HID2_HBE
/*
* MMU Setup
*/
#define CONFIG_HIGH_BATS 1
/* DDR: cache cacheable */
#define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM | BATL_PP_RW |\
BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM | BATU_BL_256M | BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
/* unused */
#define CONFIG_SYS_IBAT1L (0)
#define CONFIG_SYS_IBAT1U (0)
#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR | BATL_PP_RW |\
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS |\
BATU_VP)
#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
/* unused */
#define CONFIG_SYS_IBAT3L (0)
#define CONFIG_SYS_IBAT3U (0)
#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW |\
BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE | BATU_BL_64M |\
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K |\
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
/* PCI MEM space: cacheable */
#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_RW |\
BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M |\
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_RW | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M |\
BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
/*
* I2C EEPROM settings
*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_SIZE 0x4000
/*
* Environment Configuration
*/
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR 0xFFD00000
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
/*
* Video
*/
#define CONFIG_VIDEO
#define CONFIG_VIDEO_SM501_PCI
#define VIDEO_FB_LITTLE_ENDIAN
#define CONFIG_CMD_BMP
#define CONFIG_VIDEO_SM501
#define CONFIG_VIDEO_SM501_32BPP
#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_VIDEO_BMP_GZIP
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20)
/*
* SPI
*/
#define CONFIG_MPC8XXX_SPI
/*
* USB
*/
#define CONFIG_SYS_USB_HOST
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_STORAGE
#define CONFIG_USB_KEYBOARD
/*
*
*/
#define CONFIG_BOOTDELAY 5
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_STOP_STR "s"
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_RESET_TO_RETRY 1000
#define MV_CI "MergerBox"
#define MV_VCI "MergerBox"
#define MV_FPGA_DATA 0xfc100000
#define MV_FPGA_SIZE 0x00200000
#define CONFIG_SHOW_BOOT_PROGRESS 1
#define MV_KERNEL_ADDR_RAM 0x02800000
#define MV_DTB_ADDR_RAM 0x00600000
#define MV_INITRD_ADDR_RAM 0x01000000
#define MV_FITADDR 0xfc300000
#define MV_SPLAH_ADDR 0xffe00000
#define CONFIG_BOOTCOMMAND "run i2c_init;if test ${boot_sqfs} -eq 1;"\
"then; run fitboot;else;run ubiboot;fi;"
#define CONFIG_BOOTARGS "console=ttyS0,115200n8"
#define CONFIG_EXTRA_ENV_SETTINGS \
"console_nr=0\0"\
"stdin=serial\0"\
"stdout=serial\0"\
"stderr=serial\0"\
"boot_sqfs=1\0"\
"usb_dr_mode=host\0"\
"bootfile=MergerBox.fit\0"\
"baudrate=" __stringify(CONFIG_BAUDRATE) "\0"\
"fpga=0\0"\
"fpgadata=" __stringify(MV_FPGA_DATA) "\0"\
"fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0"\
"mv_kernel_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0"\
"mv_initrd_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0"\
"mv_dtb_ram=" __stringify(MV_DTB_ADDR_RAM) "\0"\
"uboota=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"\
"fitaddr=" __stringify(MV_FITADDR) "\0"\
"mv_version=" U_BOOT_VERSION "\0"\
"mtdids=" MTDIDS_DEFAULT "\0"\
"mtdparts=" MTDPARTS_DEFAULT "\0"\
"dhcp_client_id=" MV_CI "\0"\
"dhcp_vendor-class-identifier=" MV_VCI "\0"\
"upd_uboot=dhcp;tftp bdi2000/u-boot-mergerbox-xp.bin;"\
"protect off all;erase $uboota +0xC0000;"\
"cp.b $loadaddr $uboota $filesize\0"\
"upd_fpga=dhcp;tftp MergerBox.rbf;erase $fpgadata +$fpgadatasize;"\
"cp.b $loadaddr $fpgadata $filesize\0"\
"upd_fit=dhcp;tftp MergerBox.fit;erase $fitaddr +0x1000000;"\
"cp.b $loadaddr $fitaddr $filesize\0"\
"addsqshrfs=set bootargs $bootargs root=/dev/ram ro "\
"rootfstype=squashfs\0"\
"addubirfs=set bootargs $bootargs ubi.mtd=9 root=ubi0:rootfs rw "\
"rootfstype=ubifs\0"\
"addusbrfs=set bootargs $bootargs root=/dev/sda1 rw "\
"rootfstype=ext3 usb-storage.delay_use=1 rootdelay=3\0"\
"netusbboot=bootp;run fpganetload fitnetload addusbrfs doboot\0"\
"netubiboot= bootp;run fpganetload fitnetload addubirfs doboot\0"\
"ubiboot=run fitprep addubirfs;set mv_initrd_ram -;run doboot\0"\
"doboot=bootm $mv_kernel_ram $mv_initrd_ram $mv_dtb_ram\0"\
"fitprep=imxtract $fitaddr kernel $mv_kernel_ram;"\
"imxtract $fitaddr ramdisk $mv_initrd_ram;"\
"imxtract $fitaddr fdt $mv_dtb_ram\0"\
"fdtprep=fdt addr $mv_dtb_ram;fdt boardsetup\0"\
"fitboot=run fitprep fdtprep addsqshrfs doboot\0"\
"i2c_init=run i2c_speed init_sdi_tx i2c_init_pll\0"\
"i2c_init_pll=i2c mw 65 9 2;i2c mw 65 9 0;i2c mw 65 5 2b;"\
"i2c mw 65 7 f;i2c mw 65 8 f;i2c mw 65 11 40;i2c mw 65 12 40;"\
"i2c mw 65 13 40; i2c mw 65 14 40; i2c mw 65 a 0\0"\
"i2c_speed=i2c dev 0;i2c speed 300000;i2c dev 1;i2c speed 120000\0"\
"init_sdi_tx=i2c mw 21 6 0;i2c mw 21 2 0;i2c mw 21 3 0;sleep 1;"\
"i2c mw 21 2 ff;i2c mw 21 3 3c\0"\
"splashimage=" __stringify(MV_SPLAH_ADDR) "\0"\
""
/*
* FPGA
*/
#define CONFIG_FPGA_COUNT 1
#define CONFIG_FPGA
#define CONFIG_FPGA_ALTERA
#define CONFIG_FPGA_CYCLON2
#endif