blob: 5190cc6c0fe0a11fba99985681f08526bf449606 [file] [log] [blame]
/*
* Copyright (c) 2001 William L. Pitts
* All rights reserved.
*
* Redistribution and use in source and binary forms are freely
* permitted provided that the above copyright notice and this
* paragraph and the following disclaimer are duplicated in all
* such forms.
*
* This software is provided "AS IS" and without any express or
* implied warranties, including, without limitation, the implied
* warranties of merchantability and fitness for a particular
* purpose.
*/
#include <common.h>
#include <command.h>
#include <elf.h>
#include <net.h>
#include <vxworks.h>
#ifdef CONFIG_X86
#include <asm/e820.h>
#include <linux/linkage.h>
#endif
/*
* A very simple elf loader, assumes the image is valid, returns the
* entry point address.
*/
static unsigned long load_elf_image_phdr(unsigned long addr)
{
Elf32_Ehdr *ehdr; /* Elf header structure pointer */
Elf32_Phdr *phdr; /* Program header structure pointer */
int i;
ehdr = (Elf32_Ehdr *)addr;
phdr = (Elf32_Phdr *)(addr + ehdr->e_phoff);
/* Load each program header */
for (i = 0; i < ehdr->e_phnum; ++i) {
void *dst = (void *)(uintptr_t)phdr->p_paddr;
void *src = (void *)addr + phdr->p_offset;
debug("Loading phdr %i to 0x%p (%i bytes)\n",
i, dst, phdr->p_filesz);
if (phdr->p_filesz)
memcpy(dst, src, phdr->p_filesz);
if (phdr->p_filesz != phdr->p_memsz)
memset(dst + phdr->p_filesz, 0x00,
phdr->p_memsz - phdr->p_filesz);
flush_cache((unsigned long)dst, phdr->p_filesz);
++phdr;
}
return ehdr->e_entry;
}
static unsigned long load_elf_image_shdr(unsigned long addr)
{
Elf32_Ehdr *ehdr; /* Elf header structure pointer */
Elf32_Shdr *shdr; /* Section header structure pointer */
unsigned char *strtab = 0; /* String table pointer */
unsigned char *image; /* Binary image pointer */
int i; /* Loop counter */
ehdr = (Elf32_Ehdr *)addr;
/* Find the section header string table for output info */
shdr = (Elf32_Shdr *)(addr + ehdr->e_shoff +
(ehdr->e_shstrndx * sizeof(Elf32_Shdr)));
if (shdr->sh_type == SHT_STRTAB)
strtab = (unsigned char *)(addr + shdr->sh_offset);
/* Load each appropriate section */
for (i = 0; i < ehdr->e_shnum; ++i) {
shdr = (Elf32_Shdr *)(addr + ehdr->e_shoff +
(i * sizeof(Elf32_Shdr)));
if (!(shdr->sh_flags & SHF_ALLOC) ||
shdr->sh_addr == 0 || shdr->sh_size == 0) {
continue;
}
if (strtab) {
debug("%sing %s @ 0x%08lx (%ld bytes)\n",
(shdr->sh_type == SHT_NOBITS) ? "Clear" : "Load",
&strtab[shdr->sh_name],
(unsigned long)shdr->sh_addr,
(long)shdr->sh_size);
}
if (shdr->sh_type == SHT_NOBITS) {
memset((void *)(uintptr_t)shdr->sh_addr, 0,
shdr->sh_size);
} else {
image = (unsigned char *)addr + shdr->sh_offset;
memcpy((void *)(uintptr_t)shdr->sh_addr,
(const void *)image, shdr->sh_size);
}
flush_cache(shdr->sh_addr, shdr->sh_size);
}
return ehdr->e_entry;
}
/* Allow ports to override the default behavior */
static unsigned long do_bootelf_exec(ulong (*entry)(int, char * const[]),
int argc, char * const argv[])
{
unsigned long ret;
/*
* QNX images require the data cache is disabled.
* Data cache is already flushed, so just turn it off.
*/
int dcache = dcache_status();
if (dcache)
dcache_disable();
/*
* pass address parameter as argv[0] (aka command name),
* and all remaining args
*/
ret = entry(argc, argv);
if (dcache)
dcache_enable();
return ret;
}
/*
* Determine if a valid ELF image exists at the given memory location.
* First look at the ELF header magic field, then make sure that it is
* executable.
*/
int valid_elf_image(unsigned long addr)
{
Elf32_Ehdr *ehdr; /* Elf header structure pointer */
ehdr = (Elf32_Ehdr *)addr;
if (!IS_ELF(*ehdr)) {
printf("## No elf image at address 0x%08lx\n", addr);
return 0;
}
if (ehdr->e_type != ET_EXEC) {
printf("## Not a 32-bit elf image at address 0x%08lx\n", addr);
return 0;
}
return 1;
}
/* Interpreter command to boot an arbitrary ELF image from memory */
int do_bootelf(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
unsigned long addr; /* Address of the ELF image */
unsigned long rc; /* Return value from user code */
char *sload, *saddr;
const char *ep = getenv("autostart");
int rcode = 0;
sload = saddr = NULL;
if (argc == 3) {
sload = argv[1];
saddr = argv[2];
} else if (argc == 2) {
if (argv[1][0] == '-')
sload = argv[1];
else
saddr = argv[1];
}
if (saddr)
addr = simple_strtoul(saddr, NULL, 16);
else
addr = load_addr;
if (!valid_elf_image(addr))
return 1;
if (sload && sload[1] == 'p')
addr = load_elf_image_phdr(addr);
else
addr = load_elf_image_shdr(addr);
if (ep && !strcmp(ep, "no"))
return rcode;
printf("## Starting application at 0x%08lx ...\n", addr);
/*
* pass address parameter as argv[0] (aka command name),
* and all remaining args
*/
rc = do_bootelf_exec((void *)addr, argc - 1, argv + 1);
if (rc != 0)
rcode = 1;
printf("## Application terminated, rc = 0x%lx\n", rc);
return rcode;
}
/*
* Interpreter command to boot VxWorks from a memory image. The image can
* be either an ELF image or a raw binary. Will attempt to setup the
* bootline and other parameters correctly.
*/
int do_bootvx(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
unsigned long addr; /* Address of image */
unsigned long bootaddr; /* Address to put the bootline */
char *bootline; /* Text of the bootline */
char *tmp; /* Temporary char pointer */
char build_buf[128]; /* Buffer for building the bootline */
int ptr = 0;
#ifdef CONFIG_X86
struct e820info *info;
struct e820entry *data;
#endif
/*
* Check the loadaddr variable.
* If we don't know where the image is then we're done.
*/
if (argc < 2)
addr = load_addr;
else
addr = simple_strtoul(argv[1], NULL, 16);
#if defined(CONFIG_CMD_NET)
/*
* Check to see if we need to tftp the image ourselves
* before starting
*/
if ((argc == 2) && (strcmp(argv[1], "tftp") == 0)) {
if (net_loop(TFTPGET) <= 0)
return 1;
printf("Automatic boot of VxWorks image at address 0x%08lx ...\n",
addr);
}
#endif
/*
* This should equate to
* NV_RAM_ADRS + NV_BOOT_OFFSET + NV_ENET_OFFSET
* from the VxWorks BSP header files.
* This will vary from board to board
*/
#if defined(CONFIG_WALNUT)
tmp = (char *)CONFIG_SYS_NVRAM_BASE_ADDR + 0x500;
eth_getenv_enetaddr("ethaddr", (uchar *)build_buf);
memcpy(tmp, &build_buf[3], 3);
#elif defined(CONFIG_SYS_VXWORKS_MAC_PTR)
tmp = (char *)CONFIG_SYS_VXWORKS_MAC_PTR;
eth_getenv_enetaddr("ethaddr", (uchar *)build_buf);
memcpy(tmp, build_buf, 6);
#else
puts("## Ethernet MAC address not copied to NV RAM\n");
#endif
/*
* Use bootaddr to find the location in memory that VxWorks
* will look for the bootline string. The default value is
* (LOCAL_MEM_LOCAL_ADRS + BOOT_LINE_OFFSET) as defined by
* VxWorks BSP. For example, on PowerPC it defaults to 0x4200.
*/
tmp = getenv("bootaddr");
if (!tmp) {
printf("## VxWorks bootline address not specified\n");
} else {
bootaddr = simple_strtoul(tmp, NULL, 16);
/*
* Check to see if the bootline is defined in the 'bootargs'
* parameter. If it is not defined, we may be able to
* construct the info.
*/
bootline = getenv("bootargs");
if (bootline) {
memcpy((void *)bootaddr, bootline,
max(strlen(bootline), (size_t)255));
flush_cache(bootaddr, max(strlen(bootline),
(size_t)255));
} else {
tmp = getenv("bootdev");
if (tmp) {
strcpy(build_buf, tmp);
ptr = strlen(tmp);
} else
printf("## VxWorks boot device not specified\n");
tmp = getenv("bootfile");
if (tmp)
ptr += sprintf(build_buf + ptr,
"host:%s ", tmp);
else
ptr += sprintf(build_buf + ptr,
"host:vxWorks ");
/*
* The following parameters are only needed if 'bootdev'
* is an ethernet device, otherwise they are optional.
*/
tmp = getenv("ipaddr");
if (tmp) {
ptr += sprintf(build_buf + ptr, "e=%s", tmp);
tmp = getenv("netmask");
if (tmp) {
u32 mask = getenv_ip("netmask").s_addr;
ptr += sprintf(build_buf + ptr,
":%08x ", ntohl(mask));
} else {
ptr += sprintf(build_buf + ptr, " ");
}
}
tmp = getenv("serverip");
if (tmp)
ptr += sprintf(build_buf + ptr, "h=%s ", tmp);
tmp = getenv("gatewayip");
if (tmp)
ptr += sprintf(build_buf + ptr, "g=%s ", tmp);
tmp = getenv("hostname");
if (tmp)
ptr += sprintf(build_buf + ptr, "tn=%s ", tmp);
tmp = getenv("othbootargs");
if (tmp) {
strcpy(build_buf + ptr, tmp);
ptr += strlen(tmp);
}
memcpy((void *)bootaddr, build_buf,
max(strlen(build_buf), (size_t)255));
flush_cache(bootaddr, max(strlen(build_buf),
(size_t)255));
}
printf("## Using bootline (@ 0x%lx): %s\n", bootaddr,
(char *)bootaddr);
}
#ifdef CONFIG_X86
/*
* Since E820 information is critical to the kernel, if we don't
* specify these in the environments, use a default one.
*/
tmp = getenv("e820data");
if (tmp)
data = (struct e820entry *)simple_strtoul(tmp, NULL, 16);
else
data = (struct e820entry *)VXWORKS_E820_DATA_ADDR;
tmp = getenv("e820info");
if (tmp)
info = (struct e820info *)simple_strtoul(tmp, NULL, 16);
else
info = (struct e820info *)VXWORKS_E820_INFO_ADDR;
memset(info, 0, sizeof(struct e820info));
info->sign = E820_SIGNATURE;
info->entries = install_e820_map(E820MAX, data);
info->addr = (info->entries - 1) * sizeof(struct e820entry) +
VXWORKS_E820_DATA_ADDR;
#endif
/*
* If the data at the load address is an elf image, then
* treat it like an elf image. Otherwise, assume that it is a
* binary image.
*/
if (valid_elf_image(addr))
addr = load_elf_image_shdr(addr);
else
puts("## Not an ELF image, assuming binary\n");
printf("## Starting vxWorks at 0x%08lx ...\n", addr);
dcache_disable();
#ifdef CONFIG_X86
/* VxWorks on x86 uses stack to pass parameters */
((asmlinkage void (*)(int))addr)(0);
#else
((void (*)(int))addr)(0);
#endif
puts("## vxWorks terminated\n");
return 1;
}
U_BOOT_CMD(
bootelf, 3, 0, do_bootelf,
"Boot from an ELF image in memory",
"[-p|-s] [address]\n"
"\t- load ELF image at [address] via program headers (-p)\n"
"\t or via section headers (-s)"
);
U_BOOT_CMD(
bootvx, 2, 0, do_bootvx,
"Boot vxWorks from an ELF image",
" [address] - load address of vxWorks ELF image."
);