blob: ae1c3cf5edb41970071bb34270e393af5465184b [file] [log] [blame]
if AM33XX
choice
prompt "AM33xx board select"
optional
config TARGET_AM335X_EVM
bool "Support am335x_evm"
select BOARD_LATE_INIT
select DM
select DM_SERIAL
select DM_GPIO
select TI_I2C_BOARD_DETECT
help
This option specifies support for the AM335x
GP and HS EVM development platforms. The AM335x
GP EVM is a standalone test, development, and
evaluation module system that enables developers
to write software and develop hardware around
an AM335x processor subsystem.
config TARGET_AM335X_BALTOS
bool "Support am335x_baltos"
select BOARD_LATE_INIT
select DM
select DM_SERIAL
select DM_GPIO
config TARGET_AM335X_IGEP0033
bool "Support am335x_igep0033"
select DM
select DM_SERIAL
select DM_GPIO
config TARGET_AM335X_SHC
bool "Support am335x based shc board from bosch"
select BOARD_LATE_INIT
select DM
select DM_SERIAL
select DM_GPIO
config TARGET_AM335X_SL50
bool "Support am335x_sl50"
select BOARD_LATE_INIT
select DM
select DM_SERIAL
select DM_GPIO
config TARGET_BAV335X
bool "Support bav335x"
select BOARD_LATE_INIT
select DM
select DM_SERIAL
help
The BAV335x OEM Network Processor integrates all the functions of an
embedded network computer in a small, easy to use SODIMM module which
incorporates the popular Texas Instruments Sitara 32bit ARM Coretex-A8
processor, with fast DDR3 512MB SDRAM, 4GB of embedded MMC and a Gigabit
ethernet with simple connection to external connectors.
For more information, visit: http://birdland.com/oem
config TARGET_CM_T335
bool "Support cm_t335"
select DM
select DM_SERIAL
select DM_GPIO
config TARGET_PCM051
bool "Support pcm051"
select DM
select DM_SERIAL
select DM_GPIO
config TARGET_PENGWYN
bool "Support pengwyn"
select DM
select DM_SERIAL
select DM_GPIO
config TARGET_PEPPER
bool "Support pepper"
select DM
select DM_SERIAL
select DM_GPIO
endchoice
endif
if AM43XX
config SPL_EXT_SUPPORT
default y
config SPL_GPIO_SUPPORT
default y
config SPL_I2C_SUPPORT
default y
config TARGET_AM43XX_EVM
bool "Support am43xx_evm"
select BOARD_LATE_INIT
select TI_I2C_BOARD_DETECT
help
This option specifies support for the AM43xx
GP and HS EVM development platforms.The AM437x
GP EVM is a standalone test, development, and
evaluation module system that enables developers
to write software and develop hardware around
an AM43xx processor subsystem.
endif
if AM43XX || AM33XX
config ISW_ENTRY_ADDR
hex "Address in memory or XIP flash of bootloader entry point"
help
After any reset, the boot ROM on the AM43XX SOC
searches the boot media for a valid boot image.
For non-XIP devices, the ROM then copies the
image into internal memory.
For all boot modes, after the ROM processes the
boot image it eventually computes the entry
point address depending on the device type
(secure/non-secure), boot media (xip/non-xip) and
image headers.
default 0x402F4000 if AM43XX
default 0x402F0400 if AM33XX
config PUB_ROM_DATA_SIZE
hex "Size in bytes of the L3 SRAM reserved by ROM to store data"
help
During the device boot, the public ROM uses the top of
the public L3 OCMC RAM to store r/w data like stack,
heap, globals etc. When the ROM is copying the boot
image from the boot media into memory, the image must
not spill over into this area. This value can be used
during compile time to determine the maximum size of a
boot image. Once the ROM transfers control to the boot
image, this area is no longer used, and can be reclaimed
for run time use by the boot image.
default 0x8400
endif