blob: e33c6011062753805040fd504c310ee9e39f1113 [file] [log] [blame]
wdenkc6097192002-11-03 00:24:07 +00001#
2# (C) Copyright 2000 - 2002
3# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
4#
5# See file CREDITS for list of people who contributed to this
6# project.
7#
8# This program is free software; you can redistribute it and/or
9# modify it under the terms of the GNU General Public License as
10# published by the Free Software Foundation; either version 2 of
11# the License, or (at your option) any later version.
12#
13# This program is distributed in the hope that it will be useful,
14# but WITHOUT ANY WARRANTY; without even the implied warranty of
15# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16# GNU General Public License for more details.
17#
18# You should have received a copy of the GNU General Public License
19# along with this program; if not, write to the Free Software
20# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21# MA 02111-1307 USA
22#
23
24Summary:
25========
26
wdenk24ee89b2002-11-03 17:56:27 +000027This directory contains the source code for U-Boot, a boot loader for
28Embedded boards based on PowerPC and ARM processors, which can be
29installed in a boot ROM and used to initialize and test the hardware
30or to download and run application code.
wdenkc6097192002-11-03 00:24:07 +000031
32The development of U-Boot is closely related to Linux: some parts of
wdenk24ee89b2002-11-03 17:56:27 +000033the source code originate in the Linux source tree, we have some
34header files in common, and special provision has been made to
wdenkc6097192002-11-03 00:24:07 +000035support booting of Linux images.
36
37Some attention has been paid to make this software easily
38configurable and extendable. For instance, all monitor commands are
39implemented with the same call interface, so that it's very easy to
40add new commands. Also, instead of permanently adding rarely used
41code (for instance hardware test utilities) to the monitor, you can
42load and run it dynamically.
43
44
45Status:
46=======
47
48In general, all boards for which a configuration option exists in the
wdenk24ee89b2002-11-03 17:56:27 +000049Makefile have been tested to some extent and can be considered
wdenkc6097192002-11-03 00:24:07 +000050"working". In fact, many of them are used in production systems.
51
wdenk24ee89b2002-11-03 17:56:27 +000052In case of problems see the CHANGELOG and CREDITS files to find out
wdenkc6097192002-11-03 00:24:07 +000053who contributed the specific port.
54
wdenkc6097192002-11-03 00:24:07 +000055
56Where to get help:
57==================
58
wdenk24ee89b2002-11-03 17:56:27 +000059In case you have questions about, problems with or contributions for
60U-Boot you should send a message to the U-Boot mailing list at
61<u-boot-users@lists.sourceforge.net>. There is also an archive of
62previous traffic on the mailing list - please search the archive
wdenkc6097192002-11-03 00:24:07 +000063before asking FAQ's. Please see
64http://lists.sourceforge.net/lists/listinfo/u-boot-users/
65
66
67Where we come from:
68===================
69
70- start from 8xxrom sources
wdenk24ee89b2002-11-03 17:56:27 +000071- create PPCBoot project (http://sourceforge.net/projects/ppcboot)
wdenkc6097192002-11-03 00:24:07 +000072- clean up code
73- make it easier to add custom boards
74- make it possible to add other [PowerPC] CPUs
75- extend functions, especially:
76 * Provide extended interface to Linux boot loader
77 * S-Record download
78 * network boot
79 * PCMCIA / CompactFLash / ATA disk / SCSI ... boot
wdenk24ee89b2002-11-03 17:56:27 +000080- create ARMBoot project (http://sourceforge.net/projects/armboot)
wdenkc6097192002-11-03 00:24:07 +000081- add other CPU families (starting with ARM)
wdenk24ee89b2002-11-03 17:56:27 +000082- create U-Boot project (http://sourceforge.net/projects/u-boot)
83
84
85Names and Spelling:
86===================
87
88The "official" name of this project is "Das U-Boot". The spelling
89"U-Boot" shall be used in all written text (documentation, comments
90in source files etc.). Example:
91
92 This is the README file for the U-Boot project.
93
94File names etc. shall be based on the string "u-boot". Examples:
95
96 include/asm-ppc/u-boot.h
97
98 #include <asm/u-boot.h>
99
100Variable names, preprocessor constants etc. shall be either based on
101the string "u_boot" or on "U_BOOT". Example:
102
103 U_BOOT_VERSION u_boot_logo
104 IH_OS_U_BOOT u_boot_hush_start
wdenkc6097192002-11-03 00:24:07 +0000105
106
wdenk93f19cc2002-12-17 17:55:09 +0000107Versioning:
108===========
109
110U-Boot uses a 3 level version number containing a version, a
111sub-version, and a patchlevel: "U-Boot-2.34.5" means version "2",
112sub-version "34", and patchlevel "4".
113
114The patchlevel is used to indicate certain stages of development
115between released versions, i. e. officially released versions of
116U-Boot will always have a patchlevel of "0".
117
118
wdenkc6097192002-11-03 00:24:07 +0000119Directory Hierarchy:
120====================
121
122- board Board dependend files
123- common Misc architecture independend functions
124- cpu CPU specific files
125- disk Code for disk drive partition handling
126- doc Documentation (don't expect too much)
127- drivers Common used device drivers
128- dtt Digital Thermometer and Thermostat drivers
129- examples Example code for standalone applications, etc.
130- include Header Files
131- disk Harddisk interface code
132- net Networking code
133- ppc Files generic to PowerPC architecture
134- post Power On Self Test
135- post/arch Symlink to architecture specific Power On Self Test
136- post/arch-ppc PowerPC architecture specific Power On Self Test
137- post/cpu/mpc8260 MPC8260 CPU specific Power On Self Test
138- post/cpu/mpc8xx MPC8xx CPU specific Power On Self Test
139- rtc Real Time Clock drivers
140- tools Tools to build S-Record or U-Boot images, etc.
141
142- cpu/74xx_7xx Files specific to Motorola MPC74xx and 7xx CPUs
wdenk0db5bca2003-03-31 17:27:09 +0000143- cpu/mpc5xx Files specific to Motorola MPC5xx CPUs
wdenkc6097192002-11-03 00:24:07 +0000144- cpu/mpc8xx Files specific to Motorola MPC8xx CPUs
145- cpu/mpc824x Files specific to Motorola MPC824x CPUs
146- cpu/mpc8260 Files specific to Motorola MPC8260 CPU
147- cpu/ppc4xx Files specific to IBM 4xx CPUs
148
wdenk3bac3512003-03-12 10:41:04 +0000149- board/LEOX/ Files specific to boards manufactured by The LEOX team
150- board/LEOX/elpt860 Files specific to ELPT860 boards
wdenkc6097192002-11-03 00:24:07 +0000151- board/RPXClassic
152 Files specific to RPXClassic boards
153- board/RPXlite Files specific to RPXlite boards
wdenk2abbe072003-06-16 23:50:08 +0000154- board/at91rm9200dk Files specific to AT91RM9200DK boards
wdenkc6097192002-11-03 00:24:07 +0000155- board/c2mon Files specific to c2mon boards
wdenk0db5bca2003-03-31 17:27:09 +0000156- board/cmi Files specific to cmi boards
wdenkc6097192002-11-03 00:24:07 +0000157- board/cogent Files specific to Cogent boards
158 (need further configuration)
159 Files specific to CPCIISER4 boards
160- board/cpu86 Files specific to CPU86 boards
161- board/cray/ Files specific to boards manufactured by Cray
162- board/cray/L1 Files specific to L1 boards
163- board/cu824 Files specific to CU824 boards
164- board/ebony Files specific to IBM Ebony board
165- board/eric Files specific to ERIC boards
166- board/esd/ Files specific to boards manufactured by ESD
167- board/esd/adciop Files specific to ADCIOP boards
168- board/esd/ar405 Files specific to AR405 boards
169- board/esd/canbt Files specific to CANBT boards
170- board/esd/cpci405 Files specific to CPCI405 boards
171- board/esd/cpciiser4 Files specific to CPCIISER4 boards
172- board/esd/common Common files for ESD boards
173- board/esd/dasa_sim Files specific to DASA_SIM boards
174- board/esd/du405 Files specific to DU405 boards
175- board/esd/ocrtc Files specific to OCRTC boards
176- board/esd/pci405 Files specific to PCI405 boards
177- board/esteem192e
178 Files specific to ESTEEM192E boards
179- board/etx094 Files specific to ETX_094 boards
180- board/evb64260
181 Files specific to EVB64260 boards
182- board/fads Files specific to FADS boards
183- board/flagadm Files specific to FLAGADM boards
wdenk7aa78612003-05-03 15:50:43 +0000184- board/gen860t Files specific to GEN860T and GEN860T_SC boards
wdenkc6097192002-11-03 00:24:07 +0000185- board/genietv Files specific to GENIETV boards
186- board/gth Files specific to GTH boards
187- board/hermes Files specific to HERMES boards
188- board/hymod Files specific to HYMOD boards
189- board/icu862 Files specific to ICU862 boards
190- board/ip860 Files specific to IP860 boards
191- board/iphase4539
192 Files specific to Interphase4539 boards
193- board/ivm Files specific to IVMS8/IVML24 boards
194- board/lantec Files specific to LANTEC boards
195- board/lwmon Files specific to LWMON boards
196- board/mbx8xx Files specific to MBX boards
197- board/mpc8260ads
198 Files specific to MMPC8260ADS boards
199- board/mpl/ Files specific to boards manufactured by MPL
200- board/mpl/common Common files for MPL boards
201- board/mpl/pip405 Files specific to PIP405 boards
202- board/mpl/mip405 Files specific to MIP405 boards
203- board/musenki Files specific to MUSEKNI boards
204- board/mvs1 Files specific to MVS1 boards
205- board/nx823 Files specific to NX823 boards
206- board/oxc Files specific to OXC boards
207- board/pcippc2 Files specific to PCIPPC2/PCIPPC6 boards
208- board/pm826 Files specific to PM826 boards
209- board/ppmc8260
210 Files specific to PPMC8260 boards
211- board/rpxsuper
212 Files specific to RPXsuper boards
213- board/rsdproto
214 Files specific to RSDproto boards
215- board/sandpoint
216 Files specific to Sandpoint boards
217- board/sbc8260 Files specific to SBC8260 boards
218- board/sacsng Files specific to SACSng boards
219- board/siemens Files specific to boards manufactured by Siemens AG
220- board/siemens/CCM Files specific to CCM boards
221- board/siemens/IAD210 Files specific to IAD210 boards
222- board/siemens/SCM Files specific to SCM boards
223- board/siemens/pcu_e Files specific to PCU_E boards
224- board/sixnet Files specific to SIXNET boards
225- board/spd8xx Files specific to SPD8xxTS boards
226- board/tqm8260 Files specific to TQM8260 boards
227- board/tqm8xx Files specific to TQM8xxL boards
228- board/w7o Files specific to W7O boards
229- board/walnut405
230 Files specific to Walnut405 boards
231- board/westel/ Files specific to boards manufactured by Westel Wireless
232- board/westel/amx860 Files specific to AMX860 boards
233- board/utx8245 Files specific to UTX8245 boards
234
235Software Configuration:
236=======================
237
238Configuration is usually done using C preprocessor defines; the
239rationale behind that is to avoid dead code whenever possible.
240
241There are two classes of configuration variables:
242
243* Configuration _OPTIONS_:
244 These are selectable by the user and have names beginning with
245 "CONFIG_".
246
247* Configuration _SETTINGS_:
248 These depend on the hardware etc. and should not be meddled with if
249 you don't know what you're doing; they have names beginning with
250 "CFG_".
251
252Later we will add a configuration tool - probably similar to or even
253identical to what's used for the Linux kernel. Right now, we have to
254do the configuration by hand, which means creating some symbolic
255links and editing some configuration files. We use the TQM8xxL boards
256as an example here.
257
258
259Selection of Processor Architecture and Board Type:
260---------------------------------------------------
261
262For all supported boards there are ready-to-use default
263configurations available; just type "make <board_name>_config".
264
265Example: For a TQM823L module type:
266
267 cd u-boot
268 make TQM823L_config
269
270For the Cogent platform, you need to specify the cpu type as well;
271e.g. "make cogent_mpc8xx_config". And also configure the cogent
272directory according to the instructions in cogent/README.
273
274
275Configuration Options:
276----------------------
277
278Configuration depends on the combination of board and CPU type; all
279such information is kept in a configuration file
280"include/configs/<board_name>.h".
281
282Example: For a TQM823L module, all configuration settings are in
283"include/configs/TQM823L.h".
284
285
wdenk7f6c2cb2002-11-10 22:06:23 +0000286Many of the options are named exactly as the corresponding Linux
287kernel configuration options. The intention is to make it easier to
288build a config tool - later.
289
290
wdenkc6097192002-11-03 00:24:07 +0000291The following options need to be configured:
292
293- CPU Type: Define exactly one of
294
295 PowerPC based CPUs:
296 -------------------
297 CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
wdenk0db5bca2003-03-31 17:27:09 +0000298 or CONFIG_MPC5xx
wdenkc6097192002-11-03 00:24:07 +0000299 or CONFIG_MPC824X, CONFIG_MPC8260
300 or CONFIG_IOP480
301 or CONFIG_405GP
302 or CONFIG_440
303 or CONFIG_MPC74xx
wdenk72755c72003-06-20 23:10:58 +0000304 or CONFIG_750FX
wdenkc6097192002-11-03 00:24:07 +0000305
306 ARM based CPUs:
307 ---------------
308 CONFIG_SA1110
309 CONFIG_ARM7
310 CONFIG_PXA250
311
312
313- Board Type: Define exactly one of
314
315 PowerPC based boards:
316 ---------------------
317
318 CONFIG_ADCIOP, CONFIG_ICU862 CONFIG_RPXsuper,
319 CONFIG_ADS860, CONFIG_IP860, CONFIG_SM850,
320 CONFIG_AMX860, CONFIG_IPHASE4539, CONFIG_SPD823TS,
321 CONFIG_AR405, CONFIG_IVML24, CONFIG_SXNI855T,
322 CONFIG_BAB7xx, CONFIG_IVML24_128, CONFIG_Sandpoint8240,
323 CONFIG_CANBT, CONFIG_IVML24_256, CONFIG_Sandpoint8245,
324 CONFIG_CCM, CONFIG_IVMS8, CONFIG_TQM823L,
325 CONFIG_CPCI405, CONFIG_IVMS8_128, CONFIG_TQM850L,
326 CONFIG_CPCI4052, CONFIG_IVMS8_256, CONFIG_TQM855L,
327 CONFIG_CPCIISER4, CONFIG_LANTEC, CONFIG_TQM860L,
328 CONFIG_CPU86, CONFIG_MBX, CONFIG_TQM8260,
329 CONFIG_CRAYL1, CONFIG_MBX860T, CONFIG_TTTech,
330 CONFIG_CU824, CONFIG_MHPC, CONFIG_UTX8245,
331 CONFIG_DASA_SIM, CONFIG_MIP405, CONFIG_W7OLMC,
332 CONFIG_DU405, CONFIG_MOUSSE, CONFIG_W7OLMG,
333 CONFIG_ELPPC, CONFIG_MPC8260ADS, CONFIG_WALNUT405,
334 CONFIG_ERIC, CONFIG_MUSENKI, CONFIG_ZUMA,
335 CONFIG_ESTEEM192E, CONFIG_MVS1, CONFIG_c2mon,
336 CONFIG_ETX094, CONFIG_NX823, CONFIG_cogent_mpc8260,
337 CONFIG_EVB64260, CONFIG_OCRTC, CONFIG_cogent_mpc8xx,
338 CONFIG_FADS823, CONFIG_ORSG, CONFIG_ep8260,
339 CONFIG_FADS850SAR, CONFIG_OXC, CONFIG_gw8260,
340 CONFIG_FADS860T, CONFIG_PCI405, CONFIG_hermes,
341 CONFIG_FLAGADM, CONFIG_PCIPPC2, CONFIG_hymod,
342 CONFIG_FPS850L, CONFIG_PCIPPC6, CONFIG_lwmon,
343 CONFIG_GEN860T, CONFIG_PIP405, CONFIG_pcu_e,
344 CONFIG_GENIETV, CONFIG_PM826, CONFIG_ppmc8260,
345 CONFIG_GTH, CONFIG_RPXClassic, CONFIG_rsdproto,
346 CONFIG_IAD210, CONFIG_RPXlite, CONFIG_sbc8260,
wdenk608c9142003-01-13 23:54:46 +0000347 CONFIG_EBONY, CONFIG_sacsng, CONFIG_FPS860L,
wdenk7f70e852003-05-20 14:25:27 +0000348 CONFIG_V37, CONFIG_ELPT860, CONFIG_CMI,
wdenk682011f2003-06-03 23:54:09 +0000349 CONFIG_NETVIA, CONFIG_RBC823
wdenkc6097192002-11-03 00:24:07 +0000350
351 ARM based boards:
352 -----------------
353
354 CONFIG_HHP_CRADLE, CONFIG_DNP1110, CONFIG_EP7312,
355 CONFIG_IMPA7, CONFIG_LART, CONFIG_LUBBOCK,
356 CONFIG_SHANNON, CONFIG_SMDK2400, CONFIG_SMDK2410,
wdenk2abbe072003-06-16 23:50:08 +0000357 CONFIG_TRAB, CONFIG_AT91RM9200DK
wdenkc6097192002-11-03 00:24:07 +0000358
359
360- CPU Module Type: (if CONFIG_COGENT is defined)
361 Define exactly one of
362 CONFIG_CMA286_60_OLD
363--- FIXME --- not tested yet:
364 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
365 CONFIG_CMA287_23, CONFIG_CMA287_50
366
367- Motherboard Type: (if CONFIG_COGENT is defined)
368 Define exactly one of
369 CONFIG_CMA101, CONFIG_CMA102
370
371- Motherboard I/O Modules: (if CONFIG_COGENT is defined)
372 Define one or more of
373 CONFIG_CMA302
374
375- Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
376 Define one or more of
377 CONFIG_LCD_HEARTBEAT - update a character position on
378 the lcd display every second with
379 a "rotator" |\-/|\-/
380
381- MPC824X Family Member (if CONFIG_MPC824X is defined)
382 Define exactly one of
383 CONFIG_MPC8240, CONFIG_MPC8245
384
385- 8xx CPU Options: (if using an 8xx cpu)
386 Define one or more of
387 CONFIG_8xx_GCLK_FREQ - if get_gclk_freq() can not work e.g.
388 no 32KHz reference PIT/RTC clock
389
390- Clock Interface:
391 CONFIG_CLOCKS_IN_MHZ
392
393 U-Boot stores all clock information in Hz
394 internally. For binary compatibility with older Linux
395 kernels (which expect the clocks passed in the
396 bd_info data to be in MHz) the environment variable
397 "clocks_in_mhz" can be defined so that U-Boot
398 converts clock data to MHZ before passing it to the
399 Linux kernel.
400
401 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
402 "clocks_in_mhz=1" is automatically included in the
403 default environment.
404
405- Console Interface:
wdenk43d96162003-03-06 00:02:04 +0000406 Depending on board, define exactly one serial port
407 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
408 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
409 console by defining CONFIG_8xx_CONS_NONE
wdenkc6097192002-11-03 00:24:07 +0000410
411 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
412 port routines must be defined elsewhere
413 (i.e. serial_init(), serial_getc(), ...)
414
415 CONFIG_CFB_CONSOLE
416 Enables console device for a color framebuffer. Needs following
417 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
418 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
419 (default big endian)
420 VIDEO_HW_RECTFILL graphic chip supports
421 rectangle fill
422 (cf. smiLynxEM)
423 VIDEO_HW_BITBLT graphic chip supports
424 bit-blit (cf. smiLynxEM)
425 VIDEO_VISIBLE_COLS visible pixel columns
426 (cols=pitch)
427 VIDEO_VISIBLE_ROWS visible pixel rows
428 VIDEO_PIXEL_SIZE bytes per pixel
429 VIDEO_DATA_FORMAT graphic data format
430 (0-5, cf. cfb_console.c)
431 VIDEO_FB_ADRS framebuffer address
432 VIDEO_KBD_INIT_FCT keyboard int fct
433 (i.e. i8042_kbd_init())
434 VIDEO_TSTC_FCT test char fct
435 (i.e. i8042_tstc)
436 VIDEO_GETC_FCT get char fct
437 (i.e. i8042_getc)
438 CONFIG_CONSOLE_CURSOR cursor drawing on/off
439 (requires blink timer
440 cf. i8042.c)
441 CFG_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
442 CONFIG_CONSOLE_TIME display time/date info in
443 upper right corner
444 (requires CFG_CMD_DATE)
445 CONFIG_VIDEO_LOGO display Linux logo in
446 upper left corner
wdenka6c7ad22002-12-03 21:28:10 +0000447 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
448 linux_logo.h for logo.
449 Requires CONFIG_VIDEO_LOGO
wdenkc6097192002-11-03 00:24:07 +0000450 CONFIG_CONSOLE_EXTRA_INFO
451 addional board info beside
452 the logo
453
wdenk43d96162003-03-06 00:02:04 +0000454 When CONFIG_CFB_CONSOLE is defined, video console is
455 default i/o. Serial console can be forced with
456 environment 'console=serial'.
wdenkc6097192002-11-03 00:24:07 +0000457
458- Console Baudrate:
459 CONFIG_BAUDRATE - in bps
460 Select one of the baudrates listed in
461 CFG_BAUDRATE_TABLE, see below.
462
463- Interrupt driven serial port input:
464 CONFIG_SERIAL_SOFTWARE_FIFO
465
466 PPC405GP only.
467 Use an interrupt handler for receiving data on the
468 serial port. It also enables using hardware handshake
469 (RTS/CTS) and UART's built-in FIFO. Set the number of
470 bytes the interrupt driven input buffer should have.
471
472 Set to 0 to disable this feature (this is the default).
473 This will also disable hardware handshake.
474
stroese1d49b1f2003-05-23 11:39:05 +0000475- Console UART Number:
476 CONFIG_UART1_CONSOLE
477
478 IBM PPC4xx only.
479 If defined internal UART1 (and not UART0) is used
480 as default U-Boot console.
481
wdenkc6097192002-11-03 00:24:07 +0000482- Boot Delay: CONFIG_BOOTDELAY - in seconds
483 Delay before automatically booting the default image;
484 set to -1 to disable autoboot.
485
486 See doc/README.autoboot for these options that
487 work with CONFIG_BOOTDELAY. None are required.
488 CONFIG_BOOT_RETRY_TIME
489 CONFIG_BOOT_RETRY_MIN
490 CONFIG_AUTOBOOT_KEYED
491 CONFIG_AUTOBOOT_PROMPT
492 CONFIG_AUTOBOOT_DELAY_STR
493 CONFIG_AUTOBOOT_STOP_STR
494 CONFIG_AUTOBOOT_DELAY_STR2
495 CONFIG_AUTOBOOT_STOP_STR2
496 CONFIG_ZERO_BOOTDELAY_CHECK
497 CONFIG_RESET_TO_RETRY
498
499- Autoboot Command:
500 CONFIG_BOOTCOMMAND
501 Only needed when CONFIG_BOOTDELAY is enabled;
502 define a command string that is automatically executed
503 when no character is read on the console interface
504 within "Boot Delay" after reset.
505
506 CONFIG_BOOTARGS
wdenk43d96162003-03-06 00:02:04 +0000507 This can be used to pass arguments to the bootm
508 command. The value of CONFIG_BOOTARGS goes into the
509 environment value "bootargs".
wdenkc6097192002-11-03 00:24:07 +0000510
511 CONFIG_RAMBOOT and CONFIG_NFSBOOT
wdenk43d96162003-03-06 00:02:04 +0000512 The value of these goes into the environment as
513 "ramboot" and "nfsboot" respectively, and can be used
514 as a convenience, when switching between booting from
515 ram and nfs.
wdenkc6097192002-11-03 00:24:07 +0000516
517- Pre-Boot Commands:
518 CONFIG_PREBOOT
519
520 When this option is #defined, the existence of the
521 environment variable "preboot" will be checked
522 immediately before starting the CONFIG_BOOTDELAY
523 countdown and/or running the auto-boot command resp.
524 entering interactive mode.
525
526 This feature is especially useful when "preboot" is
527 automatically generated or modified. For an example
528 see the LWMON board specific code: here "preboot" is
529 modified when the user holds down a certain
530 combination of keys on the (special) keyboard when
531 booting the systems
532
533- Serial Download Echo Mode:
534 CONFIG_LOADS_ECHO
535 If defined to 1, all characters received during a
536 serial download (using the "loads" command) are
537 echoed back. This might be needed by some terminal
538 emulations (like "cu"), but may as well just take
539 time on others. This setting #define's the initial
540 value of the "loads_echo" environment variable.
541
542- Kgdb Serial Baudrate: (if CFG_CMD_KGDB is defined)
543 CONFIG_KGDB_BAUDRATE
544 Select one of the baudrates listed in
545 CFG_BAUDRATE_TABLE, see below.
546
547- Monitor Functions:
548 CONFIG_COMMANDS
549 Most monitor functions can be selected (or
550 de-selected) by adjusting the definition of
551 CONFIG_COMMANDS; to select individual functions,
552 #define CONFIG_COMMANDS by "OR"ing any of the
553 following values:
554
555 #define enables commands:
556 -------------------------
557 CFG_CMD_ASKENV * ask for env variable
558 CFG_CMD_BDI bdinfo
559 CFG_CMD_BEDBUG Include BedBug Debugger
560 CFG_CMD_BOOTD bootd
561 CFG_CMD_CACHE icache, dcache
562 CFG_CMD_CONSOLE coninfo
563 CFG_CMD_DATE * support for RTC, date/time...
564 CFG_CMD_DHCP DHCP support
565 CFG_CMD_ECHO * echo arguments
566 CFG_CMD_EEPROM * EEPROM read/write support
567 CFG_CMD_ELF bootelf, bootvx
568 CFG_CMD_ENV saveenv
569 CFG_CMD_FDC * Floppy Disk Support
wdenk71f95112003-06-15 22:40:42 +0000570 CFG_CMD_FAT FAT partition support
wdenk2262cfe2002-11-18 00:14:45 +0000571 CFG_CMD_FDOS * Dos diskette Support
wdenkc6097192002-11-03 00:24:07 +0000572 CFG_CMD_FLASH flinfo, erase, protect
573 CFG_CMD_FPGA FPGA device initialization support
574 CFG_CMD_I2C * I2C serial bus support
575 CFG_CMD_IDE * IDE harddisk support
576 CFG_CMD_IMI iminfo
577 CFG_CMD_IMMAP * IMMR dump support
578 CFG_CMD_IRQ * irqinfo
579 CFG_CMD_KGDB * kgdb
580 CFG_CMD_LOADB loadb
581 CFG_CMD_LOADS loads
582 CFG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
583 loop, mtest
wdenk71f95112003-06-15 22:40:42 +0000584 CFG_CMD_MMC MMC memory mapped support
wdenkc6097192002-11-03 00:24:07 +0000585 CFG_CMD_MII MII utility commands
586 CFG_CMD_NET bootp, tftpboot, rarpboot
587 CFG_CMD_PCI * pciinfo
588 CFG_CMD_PCMCIA * PCMCIA support
589 CFG_CMD_REGINFO * Register dump
590 CFG_CMD_RUN run command in env variable
591 CFG_CMD_SCSI * SCSI Support
592 CFG_CMD_SETGETDCR Support for DCR Register access (4xx only)
593 CFG_CMD_SPI * SPI serial bus support
594 CFG_CMD_USB * USB support
595 CFG_CMD_BSP * Board SPecific functions
596 -----------------------------------------------
597 CFG_CMD_ALL all
598
599 CFG_CMD_DFL Default configuration; at the moment
600 this is includes all commands, except
601 the ones marked with "*" in the list
602 above.
603
604 If you don't define CONFIG_COMMANDS it defaults to
605 CFG_CMD_DFL in include/cmd_confdefs.h. A board can
606 override the default settings in the respective
607 include file.
608
609 EXAMPLE: If you want all functions except of network
610 support you can write:
611
612 #define CONFIG_COMMANDS (CFG_CMD_ALL & ~CFG_CMD_NET)
613
614
615 Note: Don't enable the "icache" and "dcache" commands
wdenk43d96162003-03-06 00:02:04 +0000616 (configuration option CFG_CMD_CACHE) unless you know
617 what you (and your U-Boot users) are doing. Data
618 cache cannot be enabled on systems like the 8xx or
619 8260 (where accesses to the IMMR region must be
620 uncached), and it cannot be disabled on all other
621 systems where we (mis-) use the data cache to hold an
622 initial stack and some data.
wdenkc6097192002-11-03 00:24:07 +0000623
624
625 XXX - this list needs to get updated!
626
627- Watchdog:
628 CONFIG_WATCHDOG
629 If this variable is defined, it enables watchdog
630 support. There must support in the platform specific
631 code for a watchdog. For the 8xx and 8260 CPUs, the
632 SIU Watchdog feature is enabled in the SYPCR
633 register.
634
stroesec1551ea2003-04-04 15:53:41 +0000635- U-Boot Version:
636 CONFIG_VERSION_VARIABLE
637 If this variable is defined, an environment variable
638 named "ver" is created by U-Boot showing the U-Boot
639 version as printed by the "version" command.
640 This variable is readonly.
641
wdenkc6097192002-11-03 00:24:07 +0000642- Real-Time Clock:
643
644 When CFG_CMD_DATE is selected, the type of the RTC
645 has to be selected, too. Define exactly one of the
646 following options:
647
648 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
649 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
650 CONFIG_RTC_MC146818 - use MC146818 RTC
wdenk1cb8e982003-03-06 21:55:29 +0000651 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
wdenkc6097192002-11-03 00:24:07 +0000652 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
wdenk7f70e852003-05-20 14:25:27 +0000653 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
wdenk3bac3512003-03-12 10:41:04 +0000654 CONFIG_RTC_DS164x - use Dallas DS164x RTC
wdenkc6097192002-11-03 00:24:07 +0000655
656- Timestamp Support:
657
wdenk43d96162003-03-06 00:02:04 +0000658 When CONFIG_TIMESTAMP is selected, the timestamp
659 (date and time) of an image is printed by image
660 commands like bootm or iminfo. This option is
661 automatically enabled when you select CFG_CMD_DATE .
wdenkc6097192002-11-03 00:24:07 +0000662
663- Partition Support:
664 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
665 and/or CONFIG_ISO_PARTITION
666
667 If IDE or SCSI support is enabled (CFG_CMD_IDE or
668 CFG_CMD_SCSI) you must configure support for at least
669 one partition type as well.
670
671- IDE Reset method:
672 CONFIG_IDE_RESET_ROUTINE
673
674 Set this to define that instead of a reset Pin, the
675 routine ide_set_reset(int idereset) will be used.
676
677- ATAPI Support:
678 CONFIG_ATAPI
679
680 Set this to enable ATAPI support.
681
682- SCSI Support:
683 At the moment only there is only support for the
684 SYM53C8XX SCSI controller; define
685 CONFIG_SCSI_SYM53C8XX to enable it.
686
687 CFG_SCSI_MAX_LUN [8], CFG_SCSI_MAX_SCSI_ID [7] and
688 CFG_SCSI_MAX_DEVICE [CFG_SCSI_MAX_SCSI_ID *
689 CFG_SCSI_MAX_LUN] can be adjusted to define the
690 maximum numbers of LUNs, SCSI ID's and target
691 devices.
692 CFG_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
693
694- NETWORK Support (PCI):
wdenk682011f2003-06-03 23:54:09 +0000695 CONFIG_E1000
696 Support for Intel 8254x gigabit chips.
stroese53cf9432003-06-05 15:39:44 +0000697
wdenkc6097192002-11-03 00:24:07 +0000698 CONFIG_EEPRO100
699 Support for Intel 82557/82559/82559ER chips.
700 Optional CONFIG_EEPRO100_SROM_WRITE enables eeprom
701 write routine for first time initialisation.
702
703 CONFIG_TULIP
704 Support for Digital 2114x chips.
705 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
706 modem chip initialisation (KS8761/QS6611).
707
708 CONFIG_NATSEMI
709 Support for National dp83815 chips.
710
711 CONFIG_NS8382X
712 Support for National dp8382[01] gigabit chips.
713
wdenk45219c42003-05-12 21:50:16 +0000714- NETWORK Support (other):
715
716 CONFIG_DRIVER_LAN91C96
717 Support for SMSC's LAN91C96 chips.
718
719 CONFIG_LAN91C96_BASE
720 Define this to hold the physical address
721 of the LAN91C96's I/O space
722
723 CONFIG_LAN91C96_USE_32_BIT
724 Define this to enable 32 bit addressing
725
wdenkc6097192002-11-03 00:24:07 +0000726- USB Support:
727 At the moment only the UHCI host controller is
728 supported (PIP405, MIP405); define
729 CONFIG_USB_UHCI to enable it.
730 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
731 end define CONFIG_USB_STORAGE to enable the USB
732 storage devices.
733 Note:
734 Supported are USB Keyboards and USB Floppy drives
735 (TEAC FD-05PUB).
736
wdenk71f95112003-06-15 22:40:42 +0000737- MMC Support:
738 The MMC controller on the Intel PXA is supported. To
739 enable this define CONFIG_MMC. The MMC can be
740 accessed from the boot prompt by mapping the device
741 to physical memory similar to flash. Command line is
742 enabled with CFG_CMD_MMC. The MMC driver also works with
743 the FAT fs. This is enabled with CFG_CMD_FAT.
744
wdenkc6097192002-11-03 00:24:07 +0000745- Keyboard Support:
746 CONFIG_ISA_KEYBOARD
747
748 Define this to enable standard (PC-Style) keyboard
749 support
750
751 CONFIG_I8042_KBD
752 Standard PC keyboard driver with US (is default) and
753 GERMAN key layout (switch via environment 'keymap=de') support.
754 Export function i8042_kbd_init, i8042_tstc and i8042_getc
755 for cfb_console. Supports cursor blinking.
756
757- Video support:
758 CONFIG_VIDEO
759
760 Define this to enable video support (for output to
761 video).
762
763 CONFIG_VIDEO_CT69000
764
765 Enable Chips & Technologies 69000 Video chip
766
767 CONFIG_VIDEO_SMI_LYNXEM
768 Enable Silicon Motion SMI 712/710/810 Video chip
769 Videomode are selected via environment 'videomode' with
770 standard LiLo mode numbers.
771 Following modes are supported (* is default):
772
wdenk43d96162003-03-06 00:02:04 +0000773 800x600 1024x768 1280x1024
774 256 (8bit) 303* 305 307
775 65536 (16bit) 314 317 31a
776 16,7 Mill (24bit) 315 318 31b
wdenkc6097192002-11-03 00:24:07 +0000777 (i.e. setenv videomode 317; saveenv; reset;)
778
stroesec1551ea2003-04-04 15:53:41 +0000779 CONFIG_VIDEO_SED13806
wdenk43d96162003-03-06 00:02:04 +0000780 Enable Epson SED13806 driver. This driver supports 8bpp
wdenka6c7ad22002-12-03 21:28:10 +0000781 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
782 or CONFIG_VIDEO_SED13806_16BPP
783
wdenk682011f2003-06-03 23:54:09 +0000784- Keyboard Support:
785 CONFIG_KEYBOARD
786
787 Define this to enable a custom keyboard support.
788 This simply calls drv_keyboard_init() which must be
789 defined in your board-specific files.
790 The only board using this so far is RBC823.
wdenka6c7ad22002-12-03 21:28:10 +0000791
wdenkc6097192002-11-03 00:24:07 +0000792- LCD Support: CONFIG_LCD
793
794 Define this to enable LCD support (for output to LCD
795 display); also select one of the supported displays
796 by defining one of these:
797
798 CONFIG_NEC_NL6648AC33:
799
800 NEC NL6648AC33-18. Active, color, single scan.
801
802 CONFIG_NEC_NL6648BC20
803
804 NEC NL6648BC20-08. 6.5", 640x480.
805 Active, color, single scan.
806
807 CONFIG_SHARP_16x9
808
809 Sharp 320x240. Active, color, single scan.
810 It isn't 16x9, and I am not sure what it is.
811
812 CONFIG_SHARP_LQ64D341
813
814 Sharp LQ64D341 display, 640x480.
815 Active, color, single scan.
816
817 CONFIG_HLD1045
818
819 HLD1045 display, 640x480.
820 Active, color, single scan.
821
822 CONFIG_OPTREX_BW
823
824 Optrex CBL50840-2 NF-FW 99 22 M5
825 or
826 Hitachi LMG6912RPFC-00T
827 or
828 Hitachi SP14Q002
829
830 320x240. Black & white.
831
832 Normally display is black on white background; define
833 CFG_WHITE_ON_BLACK to get it inverted.
834
wdenkd791b1d2003-04-20 14:04:18 +0000835- Spash Screen Support: CONFIG_SPLASH_SCREEN
836
837 If this option is set, the environment is checked for
838 a variable "splashimage". If found, the usual display
839 of logo, copyright and system information on the LCD
840 is supressed and the BMP image at the address
841 specified in "splashimage" is loaded instead. The
842 console is redirected to the "nulldev", too. This
843 allows for a "silent" boot where a splash screen is
844 loaded very quickly after power-on.
845
846
wdenkc6097192002-11-03 00:24:07 +0000847- Ethernet address:
848 CONFIG_ETHADDR
849 CONFIG_ETH2ADDR
850 CONFIG_ETH3ADDR
851
852 Define a default value for ethernet address to use
853 for the respective ethernet interface, in case this
854 is not determined automatically.
855
856- IP address:
857 CONFIG_IPADDR
858
859 Define a default value for the IP address to use for
860 the default ethernet interface, in case this is not
861 determined through e.g. bootp.
862
863- Server IP address:
864 CONFIG_SERVERIP
865
866 Defines a default value for theIP address of a TFTP
867 server to contact when using the "tftboot" command.
868
869- BOOTP Recovery Mode:
870 CONFIG_BOOTP_RANDOM_DELAY
871
872 If you have many targets in a network that try to
873 boot using BOOTP, you may want to avoid that all
874 systems send out BOOTP requests at precisely the same
875 moment (which would happen for instance at recovery
876 from a power failure, when all systems will try to
877 boot, thus flooding the BOOTP server. Defining
878 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
879 inserted before sending out BOOTP requests. The
880 following delays are insterted then:
881
882 1st BOOTP request: delay 0 ... 1 sec
883 2nd BOOTP request: delay 0 ... 2 sec
884 3rd BOOTP request: delay 0 ... 4 sec
885 4th and following
886 BOOTP requests: delay 0 ... 8 sec
887
888- Status LED: CONFIG_STATUS_LED
889
890 Several configurations allow to display the current
891 status using a LED. For instance, the LED will blink
892 fast while running U-Boot code, stop blinking as
893 soon as a reply to a BOOTP request was received, and
894 start blinking slow once the Linux kernel is running
895 (supported by a status LED driver in the Linux
896 kernel). Defining CONFIG_STATUS_LED enables this
897 feature in U-Boot.
898
899- CAN Support: CONFIG_CAN_DRIVER
900
901 Defining CONFIG_CAN_DRIVER enables CAN driver support
902 on those systems that support this (optional)
903 feature, like the TQM8xxL modules.
904
905- I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
906
907 Enables I2C serial bus commands. If this is selected,
908 either CONFIG_HARD_I2C or CONFIG_SOFT_I2C must be defined
909 to include the appropriate I2C driver.
910
wdenk43d96162003-03-06 00:02:04 +0000911 See also: common/cmd_i2c.c for a description of the
912 command line interface.
wdenkc6097192002-11-03 00:24:07 +0000913
914
915 CONFIG_HARD_I2C
916
917 Selects the CPM hardware driver for I2C.
918
919 CONFIG_SOFT_I2C
920
921 Use software (aka bit-banging) driver instead of CPM
922 or similar hardware support for I2C. This is configured
923 via the following defines.
924
925 I2C_INIT
926
wdenk43d96162003-03-06 00:02:04 +0000927 (Optional). Any commands necessary to enable I2C
928 controller or configure ports.
wdenkc6097192002-11-03 00:24:07 +0000929
930 I2C_PORT
931
wdenk43d96162003-03-06 00:02:04 +0000932 (Only for MPC8260 CPU). The I/O port to use (the code
933 assumes both bits are on the same port). Valid values
934 are 0..3 for ports A..D.
wdenkc6097192002-11-03 00:24:07 +0000935
936 I2C_ACTIVE
937
938 The code necessary to make the I2C data line active
939 (driven). If the data line is open collector, this
940 define can be null.
941
942 I2C_TRISTATE
943
944 The code necessary to make the I2C data line tri-stated
945 (inactive). If the data line is open collector, this
946 define can be null.
947
948 I2C_READ
949
950 Code that returns TRUE if the I2C data line is high,
951 FALSE if it is low.
952
953 I2C_SDA(bit)
954
955 If <bit> is TRUE, sets the I2C data line high. If it
956 is FALSE, it clears it (low).
957
958 I2C_SCL(bit)
959
960 If <bit> is TRUE, sets the I2C clock line high. If it
961 is FALSE, it clears it (low).
962
963 I2C_DELAY
964
965 This delay is invoked four times per clock cycle so this
966 controls the rate of data transfer. The data rate thus
967 is 1 / (I2C_DELAY * 4).
968
wdenk47cd00f2003-03-06 13:39:27 +0000969 CFG_I2C_INIT_BOARD
970
971 When a board is reset during an i2c bus transfer
972 chips might think that the current transfer is still
973 in progress. On some boards it is possible to access
974 the i2c SCLK line directly, either by using the
975 processor pin as a GPIO or by having a second pin
976 connected to the bus. If this option is defined a
977 custom i2c_init_board() routine in boards/xxx/board.c
978 is run early in the boot sequence.
979
wdenkc6097192002-11-03 00:24:07 +0000980- SPI Support: CONFIG_SPI
981
982 Enables SPI driver (so far only tested with
983 SPI EEPROM, also an instance works with Crystal A/D and
984 D/As on the SACSng board)
985
986 CONFIG_SPI_X
987
988 Enables extended (16-bit) SPI EEPROM addressing.
989 (symmetrical to CONFIG_I2C_X)
990
991 CONFIG_SOFT_SPI
992
wdenk43d96162003-03-06 00:02:04 +0000993 Enables a software (bit-bang) SPI driver rather than
994 using hardware support. This is a general purpose
995 driver that only requires three general I/O port pins
996 (two outputs, one input) to function. If this is
997 defined, the board configuration must define several
998 SPI configuration items (port pins to use, etc). For
999 an example, see include/configs/sacsng.h.
wdenkc6097192002-11-03 00:24:07 +00001000
1001- FPGA Support: CONFIG_FPGA_COUNT
1002
wdenk43d96162003-03-06 00:02:04 +00001003 Specify the number of FPGA devices to support.
wdenkc6097192002-11-03 00:24:07 +00001004
wdenk43d96162003-03-06 00:02:04 +00001005 CONFIG_FPGA
wdenkc6097192002-11-03 00:24:07 +00001006
wdenk43d96162003-03-06 00:02:04 +00001007 Used to specify the types of FPGA devices. For
wdenkc6097192002-11-03 00:24:07 +00001008 example,
1009 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1010
1011 CFG_FPGA_PROG_FEEDBACK
1012
wdenk43d96162003-03-06 00:02:04 +00001013 Enable printing of hash marks during FPGA
wdenkc6097192002-11-03 00:24:07 +00001014 configuration.
1015
1016 CFG_FPGA_CHECK_BUSY
1017
wdenk43d96162003-03-06 00:02:04 +00001018 Enable checks on FPGA configuration interface busy
1019 status by the configuration function. This option
1020 will require a board or device specific function to
1021 be written.
wdenkc6097192002-11-03 00:24:07 +00001022
1023 CONFIG_FPGA_DELAY
1024
wdenk43d96162003-03-06 00:02:04 +00001025 If defined, a function that provides delays in the
1026 FPGA configuration driver.
wdenkc6097192002-11-03 00:24:07 +00001027
1028 CFG_FPGA_CHECK_CTRLC
1029
1030 Allow Control-C to interrupt FPGA configuration
1031
1032 CFG_FPGA_CHECK_ERROR
1033
wdenk43d96162003-03-06 00:02:04 +00001034 Check for configuration errors during FPGA bitfile
1035 loading. For example, abort during Virtex II
1036 configuration if the INIT_B line goes low (which
1037 indicated a CRC error).
wdenkc6097192002-11-03 00:24:07 +00001038
1039 CFG_FPGA_WAIT_INIT
1040
wdenk43d96162003-03-06 00:02:04 +00001041 Maximum time to wait for the INIT_B line to deassert
1042 after PROB_B has been deasserted during a Virtex II
1043 FPGA configuration sequence. The default time is 500 mS.
wdenkc6097192002-11-03 00:24:07 +00001044
1045 CFG_FPGA_WAIT_BUSY
1046
wdenk43d96162003-03-06 00:02:04 +00001047 Maximum time to wait for BUSY to deassert during
1048 Virtex II FPGA configuration. The default is 5 mS.
wdenkc6097192002-11-03 00:24:07 +00001049
1050 CFG_FPGA_WAIT_CONFIG
1051
wdenk43d96162003-03-06 00:02:04 +00001052 Time to wait after FPGA configuration. The default is
wdenkc6097192002-11-03 00:24:07 +00001053 200 mS.
1054
1055- FPGA Support: CONFIG_FPGA_COUNT
1056
1057 Specify the number of FPGA devices to support.
1058
1059 CONFIG_FPGA
1060
1061 Used to specify the types of FPGA devices. For example,
1062 #define CONFIG_FPGA CFG_XILINX_VIRTEX2
1063
1064 CFG_FPGA_PROG_FEEDBACK
1065
1066 Enable printing of hash marks during FPGA configuration.
1067
1068 CFG_FPGA_CHECK_BUSY
1069
wdenk43d96162003-03-06 00:02:04 +00001070 Enable checks on FPGA configuration interface busy
1071 status by the configuration function. This option
1072 will require a board or device specific function to
1073 be written.
wdenkc6097192002-11-03 00:24:07 +00001074
1075 CONFIG_FPGA_DELAY
1076
1077 If defined, a function that provides delays in the FPGA
1078 configuration driver.
1079
1080 CFG_FPGA_CHECK_CTRLC
1081 Allow Control-C to interrupt FPGA configuration
1082
1083 CFG_FPGA_CHECK_ERROR
1084
wdenk43d96162003-03-06 00:02:04 +00001085 Check for configuration errors during FPGA bitfile
1086 loading. For example, abort during Virtex II
1087 configuration if the INIT_B line goes low (which
1088 indicated a CRC error).
wdenkc6097192002-11-03 00:24:07 +00001089
1090 CFG_FPGA_WAIT_INIT
1091
wdenk43d96162003-03-06 00:02:04 +00001092 Maximum time to wait for the INIT_B line to deassert
1093 after PROB_B has been deasserted during a Virtex II
1094 FPGA configuration sequence. The default time is 500
1095 mS.
wdenkc6097192002-11-03 00:24:07 +00001096
1097 CFG_FPGA_WAIT_BUSY
1098
wdenk43d96162003-03-06 00:02:04 +00001099 Maximum time to wait for BUSY to deassert during
1100 Virtex II FPGA configuration. The default is 5 mS.
wdenkc6097192002-11-03 00:24:07 +00001101
1102 CFG_FPGA_WAIT_CONFIG
1103
wdenk43d96162003-03-06 00:02:04 +00001104 Time to wait after FPGA configuration. The default is
1105 200 mS.
wdenkc6097192002-11-03 00:24:07 +00001106
1107- Configuration Management:
1108 CONFIG_IDENT_STRING
1109
wdenk43d96162003-03-06 00:02:04 +00001110 If defined, this string will be added to the U-Boot
1111 version information (U_BOOT_VERSION)
wdenkc6097192002-11-03 00:24:07 +00001112
1113- Vendor Parameter Protection:
1114
wdenk43d96162003-03-06 00:02:04 +00001115 U-Boot considers the values of the environment
1116 variables "serial#" (Board Serial Number) and
1117 "ethaddr" (Ethernet Address) to bb parameters that
1118 are set once by the board vendor / manufacturer, and
1119 protects these variables from casual modification by
1120 the user. Once set, these variables are read-only,
1121 and write or delete attempts are rejected. You can
1122 change this behviour:
wdenkc6097192002-11-03 00:24:07 +00001123
1124 If CONFIG_ENV_OVERWRITE is #defined in your config
1125 file, the write protection for vendor parameters is
wdenk47cd00f2003-03-06 13:39:27 +00001126 completely disabled. Anybody can change or delete
wdenkc6097192002-11-03 00:24:07 +00001127 these parameters.
1128
1129 Alternatively, if you #define _both_ CONFIG_ETHADDR
1130 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1131 ethernet address is installed in the environment,
1132 which can be changed exactly ONCE by the user. [The
1133 serial# is unaffected by this, i. e. it remains
1134 read-only.]
1135
1136- Protected RAM:
1137 CONFIG_PRAM
1138
1139 Define this variable to enable the reservation of
1140 "protected RAM", i. e. RAM which is not overwritten
1141 by U-Boot. Define CONFIG_PRAM to hold the number of
1142 kB you want to reserve for pRAM. You can overwrite
1143 this default value by defining an environment
1144 variable "pram" to the number of kB you want to
1145 reserve. Note that the board info structure will
1146 still show the full amount of RAM. If pRAM is
1147 reserved, a new environment variable "mem" will
1148 automatically be defined to hold the amount of
1149 remaining RAM in a form that can be passed as boot
1150 argument to Linux, for instance like that:
1151
1152 setenv bootargs ... mem=\$(mem)
1153 saveenv
1154
1155 This way you can tell Linux not to use this memory,
1156 either, which results in a memory region that will
1157 not be affected by reboots.
1158
1159 *WARNING* If your board configuration uses automatic
1160 detection of the RAM size, you must make sure that
1161 this memory test is non-destructive. So far, the
1162 following board configurations are known to be
1163 "pRAM-clean":
1164
1165 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1166 HERMES, IP860, RPXlite, LWMON, LANTEC,
1167 PCU_E, FLAGADM, TQM8260
1168
1169- Error Recovery:
1170 CONFIG_PANIC_HANG
1171
1172 Define this variable to stop the system in case of a
1173 fatal error, so that you have to reset it manually.
1174 This is probably NOT a good idea for an embedded
1175 system where you want to system to reboot
1176 automatically as fast as possible, but it may be
1177 useful during development since you can try to debug
1178 the conditions that lead to the situation.
1179
1180 CONFIG_NET_RETRY_COUNT
1181
wdenk43d96162003-03-06 00:02:04 +00001182 This variable defines the number of retries for
1183 network operations like ARP, RARP, TFTP, or BOOTP
1184 before giving up the operation. If not defined, a
1185 default value of 5 is used.
wdenkc6097192002-11-03 00:24:07 +00001186
1187- Command Interpreter:
1188 CFG_HUSH_PARSER
1189
1190 Define this variable to enable the "hush" shell (from
1191 Busybox) as command line interpreter, thus enabling
1192 powerful command line syntax like
1193 if...then...else...fi conditionals or `&&' and '||'
1194 constructs ("shell scripts").
1195
1196 If undefined, you get the old, much simpler behaviour
1197 with a somewhat smaller memory footprint.
1198
1199
1200 CFG_PROMPT_HUSH_PS2
1201
1202 This defines the secondary prompt string, which is
1203 printed when the command interpreter needs more input
1204 to complete a command. Usually "> ".
1205
1206 Note:
1207
wdenk3b57fe02003-05-30 12:48:29 +00001208 In the current implementation, the local variables
1209 space and global environment variables space are
1210 separated. Local variables are those you define by
1211 simply typing `name=value'. To access a local
1212 variable later on, you have write `$name' or
1213 `${name}'; to execute the contents of a variable
1214 directly type `$name' at the command prompt.
wdenkc6097192002-11-03 00:24:07 +00001215
wdenk43d96162003-03-06 00:02:04 +00001216 Global environment variables are those you use
1217 setenv/printenv to work with. To run a command stored
1218 in such a variable, you need to use the run command,
1219 and you must not use the '$' sign to access them.
wdenkc6097192002-11-03 00:24:07 +00001220
1221 To store commands and special characters in a
1222 variable, please use double quotation marks
1223 surrounding the whole text of the variable, instead
1224 of the backslashes before semicolons and special
1225 symbols.
1226
1227- Default Environment
1228 CONFIG_EXTRA_ENV_SETTINGS
1229
wdenk43d96162003-03-06 00:02:04 +00001230 Define this to contain any number of null terminated
1231 strings (variable = value pairs) that will be part of
1232 the default enviroment compiled into the boot image.
wdenk2262cfe2002-11-18 00:14:45 +00001233
wdenk43d96162003-03-06 00:02:04 +00001234 For example, place something like this in your
1235 board's config file:
wdenkc6097192002-11-03 00:24:07 +00001236
1237 #define CONFIG_EXTRA_ENV_SETTINGS \
1238 "myvar1=value1\0" \
1239 "myvar2=value2\0"
1240
wdenk43d96162003-03-06 00:02:04 +00001241 Warning: This method is based on knowledge about the
1242 internal format how the environment is stored by the
1243 U-Boot code. This is NOT an official, exported
1244 interface! Although it is unlikely that this format
1245 will change soon, but there is no guarantee either.
wdenkc6097192002-11-03 00:24:07 +00001246 You better know what you are doing here.
1247
wdenk43d96162003-03-06 00:02:04 +00001248 Note: overly (ab)use of the default environment is
1249 discouraged. Make sure to check other ways to preset
1250 the environment like the autoscript function or the
1251 boot command first.
wdenkc6097192002-11-03 00:24:07 +00001252
wdenk2abbe072003-06-16 23:50:08 +00001253- DataFlash Support
1254 CONFIG_HAS_DATAFLASH
1255
1256 Defining this option enables DataFlash features and
1257 allows to read/write in Dataflash via the standard
1258 commands cp, md...
1259
wdenkc6097192002-11-03 00:24:07 +00001260- Show boot progress
1261 CONFIG_SHOW_BOOT_PROGRESS
1262
wdenk43d96162003-03-06 00:02:04 +00001263 Defining this option allows to add some board-
1264 specific code (calling a user-provided function
1265 "show_boot_progress(int)") that enables you to show
1266 the system's boot progress on some display (for
1267 example, some LED's) on your board. At the moment,
1268 the following checkpoints are implemented:
wdenkc6097192002-11-03 00:24:07 +00001269
1270 Arg Where When
1271 1 common/cmd_bootm.c before attempting to boot an image
1272 -1 common/cmd_bootm.c Image header has bad magic number
1273 2 common/cmd_bootm.c Image header has correct magic number
1274 -2 common/cmd_bootm.c Image header has bad checksum
1275 3 common/cmd_bootm.c Image header has correct checksum
1276 -3 common/cmd_bootm.c Image data has bad checksum
1277 4 common/cmd_bootm.c Image data has correct checksum
1278 -4 common/cmd_bootm.c Image is for unsupported architecture
1279 5 common/cmd_bootm.c Architecture check OK
1280 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1281 6 common/cmd_bootm.c Image Type check OK
1282 -6 common/cmd_bootm.c gunzip uncompression error
1283 -7 common/cmd_bootm.c Unimplemented compression type
1284 7 common/cmd_bootm.c Uncompression OK
1285 -8 common/cmd_bootm.c Wrong Image Type (not kernel, multi, standalone)
1286 8 common/cmd_bootm.c Image Type check OK
1287 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
1288 9 common/cmd_bootm.c Start initial ramdisk verification
1289 -10 common/cmd_bootm.c Ramdisk header has bad magic number
1290 -11 common/cmd_bootm.c Ramdisk header has bad checksum
1291 10 common/cmd_bootm.c Ramdisk header is OK
1292 -12 common/cmd_bootm.c Ramdisk data has bad checksum
1293 11 common/cmd_bootm.c Ramdisk data has correct checksum
1294 12 common/cmd_bootm.c Ramdisk verification complete, start loading
1295 -13 common/cmd_bootm.c Wrong Image Type (not PPC Linux Ramdisk)
1296 13 common/cmd_bootm.c Start multifile image verification
1297 14 common/cmd_bootm.c No initial ramdisk, no multifile, continue.
1298 15 common/cmd_bootm.c All preparation done, transferring control to OS
1299
1300 -1 common/cmd_doc.c Bad usage of "doc" command
1301 -1 common/cmd_doc.c No boot device
1302 -1 common/cmd_doc.c Unknown Chip ID on boot device
1303 -1 common/cmd_doc.c Read Error on boot device
1304 -1 common/cmd_doc.c Image header has bad magic number
1305
1306 -1 common/cmd_ide.c Bad usage of "ide" command
1307 -1 common/cmd_ide.c No boot device
1308 -1 common/cmd_ide.c Unknown boot device
1309 -1 common/cmd_ide.c Unknown partition table
1310 -1 common/cmd_ide.c Invalid partition type
1311 -1 common/cmd_ide.c Read Error on boot device
1312 -1 common/cmd_ide.c Image header has bad magic number
1313
1314 -1 common/cmd_nvedit.c Environment not changable, but has bad CRC
1315
1316
1317Modem Support:
1318--------------
1319
wdenk85ec0bc2003-03-31 16:34:49 +00001320[so far only for SMDK2400 and TRAB boards]
wdenkc6097192002-11-03 00:24:07 +00001321
1322- Modem support endable:
1323 CONFIG_MODEM_SUPPORT
1324
1325- RTS/CTS Flow control enable:
1326 CONFIG_HWFLOW
1327
1328- Modem debug support:
1329 CONFIG_MODEM_SUPPORT_DEBUG
1330
wdenk43d96162003-03-06 00:02:04 +00001331 Enables debugging stuff (char screen[1024], dbg())
1332 for modem support. Useful only with BDI2000.
wdenkc6097192002-11-03 00:24:07 +00001333
1334- General:
1335
wdenk43d96162003-03-06 00:02:04 +00001336 In the target system modem support is enabled when a
1337 specific key (key combination) is pressed during
1338 power-on. Otherwise U-Boot will boot normally
1339 (autoboot). The key_pressed() fuction is called from
1340 board_init(). Currently key_pressed() is a dummy
1341 function, returning 1 and thus enabling modem
1342 initialization.
wdenkc6097192002-11-03 00:24:07 +00001343
wdenk43d96162003-03-06 00:02:04 +00001344 If there are no modem init strings in the
1345 environment, U-Boot proceed to autoboot; the
1346 previous output (banner, info printfs) will be
1347 supressed, though.
wdenkc6097192002-11-03 00:24:07 +00001348
1349 See also: doc/README.Modem
1350
1351
1352
1353
1354Configuration Settings:
1355-----------------------
1356
1357- CFG_LONGHELP: Defined when you want long help messages included;
1358 undefine this when you're short of memory.
1359
1360- CFG_PROMPT: This is what U-Boot prints on the console to
1361 prompt for user input.
1362
1363- CFG_CBSIZE: Buffer size for input from the Console
1364
1365- CFG_PBSIZE: Buffer size for Console output
1366
1367- CFG_MAXARGS: max. Number of arguments accepted for monitor commands
1368
1369- CFG_BARGSIZE: Buffer size for Boot Arguments which are passed to
1370 the application (usually a Linux kernel) when it is
1371 booted
1372
1373- CFG_BAUDRATE_TABLE:
1374 List of legal baudrate settings for this board.
1375
1376- CFG_CONSOLE_INFO_QUIET
1377 Suppress display of console information at boot.
1378
1379- CFG_CONSOLE_IS_IN_ENV
1380 If the board specific function
1381 extern int overwrite_console (void);
1382 returns 1, the stdin, stderr and stdout are switched to the
1383 serial port, else the settings in the environment are used.
1384
1385- CFG_CONSOLE_OVERWRITE_ROUTINE
1386 Enable the call to overwrite_console().
1387
1388- CFG_CONSOLE_ENV_OVERWRITE
1389 Enable overwrite of previous console environment settings.
1390
1391- CFG_MEMTEST_START, CFG_MEMTEST_END:
1392 Begin and End addresses of the area used by the
1393 simple memory test.
1394
1395- CFG_ALT_MEMTEST:
1396 Enable an alternate, more extensive memory test.
1397
1398- CFG_TFTP_LOADADDR:
1399 Default load address for network file downloads
1400
1401- CFG_LOADS_BAUD_CHANGE:
1402 Enable temporary baudrate change while serial download
1403
1404- CFG_SDRAM_BASE:
1405 Physical start address of SDRAM. _Must_ be 0 here.
1406
1407- CFG_MBIO_BASE:
1408 Physical start address of Motherboard I/O (if using a
1409 Cogent motherboard)
1410
1411- CFG_FLASH_BASE:
1412 Physical start address of Flash memory.
1413
1414- CFG_MONITOR_BASE:
1415 Physical start address of boot monitor code (set by
1416 make config files to be same as the text base address
1417 (TEXT_BASE) used when linking) - same as
1418 CFG_FLASH_BASE when booting from flash.
1419
1420- CFG_MONITOR_LEN:
wdenk3b57fe02003-05-30 12:48:29 +00001421 Size of memory reserved for monitor code, used to
1422 determine _at_compile_time_ (!) if the environment is
1423 embedded within the U-Boot image, or in a separate
1424 flash sector.
wdenkc6097192002-11-03 00:24:07 +00001425
1426- CFG_MALLOC_LEN:
1427 Size of DRAM reserved for malloc() use.
1428
1429- CFG_BOOTMAPSZ:
1430 Maximum size of memory mapped by the startup code of
1431 the Linux kernel; all data that must be processed by
1432 the Linux kernel (bd_info, boot arguments, eventually
1433 initrd image) must be put below this limit.
1434
1435- CFG_MAX_FLASH_BANKS:
1436 Max number of Flash memory banks
1437
1438- CFG_MAX_FLASH_SECT:
1439 Max number of sectors on a Flash chip
1440
1441- CFG_FLASH_ERASE_TOUT:
1442 Timeout for Flash erase operations (in ms)
1443
1444- CFG_FLASH_WRITE_TOUT:
1445 Timeout for Flash write operations (in ms)
1446
1447- CFG_DIRECT_FLASH_TFTP:
1448
1449 Enable TFTP transfers directly to flash memory;
1450 without this option such a download has to be
1451 performed in two steps: (1) download to RAM, and (2)
1452 copy from RAM to flash.
1453
1454 The two-step approach is usually more reliable, since
1455 you can check if the download worked before you erase
1456 the flash, but in some situations (when sytem RAM is
1457 too limited to allow for a tempory copy of the
1458 downloaded image) this option may be very useful.
1459
1460- CFG_FLASH_CFI:
wdenk43d96162003-03-06 00:02:04 +00001461 Define if the flash driver uses extra elements in the
1462 common flash structure for storing flash geometry
wdenkc6097192002-11-03 00:24:07 +00001463
stroese53cf9432003-06-05 15:39:44 +00001464- CFG_RX_ETH_BUFFER:
1465 Defines the number of ethernet receive buffers. On some
1466 ethernet controllers it is recommended to set this value
1467 to 8 or even higher (EEPRO100 or 405 EMAC), since all
1468 buffers can be full shortly after enabling the interface
1469 on high ethernet traffic.
1470 Defaults to 4 if not defined.
1471
wdenkc6097192002-11-03 00:24:07 +00001472The following definitions that deal with the placement and management
1473of environment data (variable area); in general, we support the
1474following configurations:
1475
1476- CFG_ENV_IS_IN_FLASH:
1477
1478 Define this if the environment is in flash memory.
1479
1480 a) The environment occupies one whole flash sector, which is
1481 "embedded" in the text segment with the U-Boot code. This
1482 happens usually with "bottom boot sector" or "top boot
1483 sector" type flash chips, which have several smaller
1484 sectors at the start or the end. For instance, such a
1485 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
1486 such a case you would place the environment in one of the
1487 4 kB sectors - with U-Boot code before and after it. With
1488 "top boot sector" type flash chips, you would put the
1489 environment in one of the last sectors, leaving a gap
1490 between U-Boot and the environment.
1491
1492 - CFG_ENV_OFFSET:
1493
1494 Offset of environment data (variable area) to the
1495 beginning of flash memory; for instance, with bottom boot
1496 type flash chips the second sector can be used: the offset
1497 for this sector is given here.
1498
1499 CFG_ENV_OFFSET is used relative to CFG_FLASH_BASE.
1500
1501 - CFG_ENV_ADDR:
1502
1503 This is just another way to specify the start address of
1504 the flash sector containing the environment (instead of
1505 CFG_ENV_OFFSET).
1506
1507 - CFG_ENV_SECT_SIZE:
1508
1509 Size of the sector containing the environment.
1510
1511
1512 b) Sometimes flash chips have few, equal sized, BIG sectors.
1513 In such a case you don't want to spend a whole sector for
1514 the environment.
1515
1516 - CFG_ENV_SIZE:
1517
1518 If you use this in combination with CFG_ENV_IS_IN_FLASH
1519 and CFG_ENV_SECT_SIZE, you can specify to use only a part
1520 of this flash sector for the environment. This saves
1521 memory for the RAM copy of the environment.
1522
1523 It may also save flash memory if you decide to use this
1524 when your environment is "embedded" within U-Boot code,
1525 since then the remainder of the flash sector could be used
1526 for U-Boot code. It should be pointed out that this is
1527 STRONGLY DISCOURAGED from a robustness point of view:
1528 updating the environment in flash makes it always
1529 necessary to erase the WHOLE sector. If something goes
1530 wrong before the contents has been restored from a copy in
1531 RAM, your target system will be dead.
1532
1533 - CFG_ENV_ADDR_REDUND
1534 CFG_ENV_SIZE_REDUND
1535
wdenk43d96162003-03-06 00:02:04 +00001536 These settings describe a second storage area used to hold
1537 a redundand copy of the environment data, so that there is
wdenk3e386912003-04-05 00:53:31 +00001538 a valid backup copy in case there is a power failure during
wdenk43d96162003-03-06 00:02:04 +00001539 a "saveenv" operation.
wdenkc6097192002-11-03 00:24:07 +00001540
1541BE CAREFUL! Any changes to the flash layout, and some changes to the
1542source code will make it necessary to adapt <board>/u-boot.lds*
1543accordingly!
1544
1545
1546- CFG_ENV_IS_IN_NVRAM:
1547
1548 Define this if you have some non-volatile memory device
1549 (NVRAM, battery buffered SRAM) which you want to use for the
1550 environment.
1551
1552 - CFG_ENV_ADDR:
1553 - CFG_ENV_SIZE:
1554
1555 These two #defines are used to determin the memory area you
1556 want to use for environment. It is assumed that this memory
1557 can just be read and written to, without any special
1558 provision.
1559
1560BE CAREFUL! The first access to the environment happens quite early
1561in U-Boot initalization (when we try to get the setting of for the
1562console baudrate). You *MUST* have mappend your NVRAM area then, or
1563U-Boot will hang.
1564
1565Please note that even with NVRAM we still use a copy of the
1566environment in RAM: we could work on NVRAM directly, but we want to
1567keep settings there always unmodified except somebody uses "saveenv"
1568to save the current settings.
1569
1570
1571- CFG_ENV_IS_IN_EEPROM:
1572
1573 Use this if you have an EEPROM or similar serial access
1574 device and a driver for it.
1575
1576 - CFG_ENV_OFFSET:
1577 - CFG_ENV_SIZE:
1578
1579 These two #defines specify the offset and size of the
1580 environment area within the total memory of your EEPROM.
1581
1582 - CFG_I2C_EEPROM_ADDR:
1583 If defined, specified the chip address of the EEPROM device.
1584 The default address is zero.
1585
1586 - CFG_EEPROM_PAGE_WRITE_BITS:
1587 If defined, the number of bits used to address bytes in a
1588 single page in the EEPROM device. A 64 byte page, for example
1589 would require six bits.
1590
1591 - CFG_EEPROM_PAGE_WRITE_DELAY_MS:
1592 If defined, the number of milliseconds to delay between
1593 page writes. The default is zero milliseconds.
1594
1595 - CFG_I2C_EEPROM_ADDR_LEN:
1596 The length in bytes of the EEPROM memory array address. Note
1597 that this is NOT the chip address length!
1598
1599 - CFG_EEPROM_SIZE:
1600 The size in bytes of the EEPROM device.
1601
wdenkc6097192002-11-03 00:24:07 +00001602
1603- CFG_SPI_INIT_OFFSET
1604
1605 Defines offset to the initial SPI buffer area in DPRAM. The
1606 area is used at an early stage (ROM part) if the environment
1607 is configured to reside in the SPI EEPROM: We need a 520 byte
1608 scratch DPRAM area. It is used between the two initialization
1609 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
1610 to be a good choice since it makes it far enough from the
1611 start of the data area as well as from the stack pointer.
1612
1613Please note that the environment is read-only as long as the monitor
1614has been relocated to RAM and a RAM copy of the environment has been
1615created; also, when using EEPROM you will have to use getenv_r()
1616until then to read environment variables.
1617
wdenk85ec0bc2003-03-31 16:34:49 +00001618The environment is protected by a CRC32 checksum. Before the monitor
1619is relocated into RAM, as a result of a bad CRC you will be working
1620with the compiled-in default environment - *silently*!!! [This is
1621necessary, because the first environment variable we need is the
1622"baudrate" setting for the console - if we have a bad CRC, we don't
1623have any device yet where we could complain.]
wdenkc6097192002-11-03 00:24:07 +00001624
1625Note: once the monitor has been relocated, then it will complain if
1626the default environment is used; a new CRC is computed as soon as you
wdenk85ec0bc2003-03-31 16:34:49 +00001627use the "saveenv" command to store a valid environment.
wdenkc6097192002-11-03 00:24:07 +00001628
1629
wdenkc6097192002-11-03 00:24:07 +00001630Low Level (hardware related) configuration options:
wdenkdc7c9a12003-03-26 06:55:25 +00001631---------------------------------------------------
wdenkc6097192002-11-03 00:24:07 +00001632
1633- CFG_CACHELINE_SIZE:
1634 Cache Line Size of the CPU.
1635
1636- CFG_DEFAULT_IMMR:
1637 Default address of the IMMR after system reset.
1638 Needed on some 8260 systems (MPC8260ADS and RPXsuper)
1639 to be able to adjust the position of the IMMR
1640 register after a reset.
1641
wdenk7f6c2cb2002-11-10 22:06:23 +00001642- Floppy Disk Support:
1643 CFG_FDC_DRIVE_NUMBER
1644
1645 the default drive number (default value 0)
1646
1647 CFG_ISA_IO_STRIDE
1648
1649 defines the spacing between fdc chipset registers
1650 (default value 1)
1651
1652 CFG_ISA_IO_OFFSET
1653
wdenk43d96162003-03-06 00:02:04 +00001654 defines the offset of register from address. It
1655 depends on which part of the data bus is connected to
1656 the fdc chipset. (default value 0)
wdenk7f6c2cb2002-11-10 22:06:23 +00001657
wdenk43d96162003-03-06 00:02:04 +00001658 If CFG_ISA_IO_STRIDE CFG_ISA_IO_OFFSET and
1659 CFG_FDC_DRIVE_NUMBER are undefined, they take their
1660 default value.
wdenk7f6c2cb2002-11-10 22:06:23 +00001661
wdenk43d96162003-03-06 00:02:04 +00001662 if CFG_FDC_HW_INIT is defined, then the function
1663 fdc_hw_init() is called at the beginning of the FDC
1664 setup. fdc_hw_init() must be provided by the board
1665 source code. It is used to make hardware dependant
1666 initializations.
wdenk7f6c2cb2002-11-10 22:06:23 +00001667
wdenkc6097192002-11-03 00:24:07 +00001668- CFG_IMMR: Physical address of the Internal Memory Mapped
1669 Register; DO NOT CHANGE! (11-4)
1670 [MPC8xx systems only]
1671
1672- CFG_INIT_RAM_ADDR:
1673
1674 Start address of memory area tha can be used for
1675 initial data and stack; please note that this must be
1676 writable memory that is working WITHOUT special
1677 initialization, i. e. you CANNOT use normal RAM which
1678 will become available only after programming the
1679 memory controller and running certain initialization
1680 sequences.
1681
1682 U-Boot uses the following memory types:
1683 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
1684 - MPC824X: data cache
1685 - PPC4xx: data cache
1686
wdenk85ec0bc2003-03-31 16:34:49 +00001687- CFG_GBL_DATA_OFFSET:
wdenkc6097192002-11-03 00:24:07 +00001688
1689 Offset of the initial data structure in the memory
1690 area defined by CFG_INIT_RAM_ADDR. Usually
wdenk85ec0bc2003-03-31 16:34:49 +00001691 CFG_GBL_DATA_OFFSET is chosen such that the initial
wdenkc6097192002-11-03 00:24:07 +00001692 data is located at the end of the available space
1693 (sometimes written as (CFG_INIT_RAM_END -
1694 CFG_INIT_DATA_SIZE), and the initial stack is just
1695 below that area (growing from (CFG_INIT_RAM_ADDR +
wdenk85ec0bc2003-03-31 16:34:49 +00001696 CFG_GBL_DATA_OFFSET) downward.
wdenkc6097192002-11-03 00:24:07 +00001697
1698 Note:
1699 On the MPC824X (or other systems that use the data
1700 cache for initial memory) the address chosen for
1701 CFG_INIT_RAM_ADDR is basically arbitrary - it must
1702 point to an otherwise UNUSED address space between
1703 the top of RAM and the start of the PCI space.
1704
1705- CFG_SIUMCR: SIU Module Configuration (11-6)
1706
1707- CFG_SYPCR: System Protection Control (11-9)
1708
1709- CFG_TBSCR: Time Base Status and Control (11-26)
1710
1711- CFG_PISCR: Periodic Interrupt Status and Control (11-31)
1712
1713- CFG_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
1714
1715- CFG_SCCR: System Clock and reset Control Register (15-27)
1716
1717- CFG_OR_TIMING_SDRAM:
1718 SDRAM timing
1719
1720- CFG_MAMR_PTA:
1721 periodic timer for refresh
1722
1723- CFG_DER: Debug Event Register (37-47)
1724
1725- FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CFG_REMAP_OR_AM,
1726 CFG_PRELIM_OR_AM, CFG_OR_TIMING_FLASH, CFG_OR0_REMAP,
1727 CFG_OR0_PRELIM, CFG_BR0_PRELIM, CFG_OR1_REMAP, CFG_OR1_PRELIM,
1728 CFG_BR1_PRELIM:
1729 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
1730
1731- SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
1732 CFG_OR_TIMING_SDRAM, CFG_OR2_PRELIM, CFG_BR2_PRELIM,
1733 CFG_OR3_PRELIM, CFG_BR3_PRELIM:
1734 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
1735
1736- CFG_MAMR_PTA, CFG_MPTPR_2BK_4K, CFG_MPTPR_1BK_4K, CFG_MPTPR_2BK_8K,
1737 CFG_MPTPR_1BK_8K, CFG_MAMR_8COL, CFG_MAMR_9COL:
1738 Machine Mode Register and Memory Periodic Timer
1739 Prescaler definitions (SDRAM timing)
1740
1741- CFG_I2C_UCODE_PATCH, CFG_I2C_DPMEM_OFFSET [0x1FC0]:
1742 enable I2C microcode relocation patch (MPC8xx);
1743 define relocation offset in DPRAM [DSP2]
1744
1745- CFG_SPI_UCODE_PATCH, CFG_SPI_DPMEM_OFFSET [0x1FC0]:
1746 enable SPI microcode relocation patch (MPC8xx);
1747 define relocation offset in DPRAM [SCC4]
1748
1749- CFG_USE_OSCCLK:
1750 Use OSCM clock mode on MBX8xx board. Be careful,
1751 wrong setting might damage your board. Read
1752 doc/README.MBX before setting this variable!
1753
wdenkea909b72002-11-21 23:11:29 +00001754- CFG_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
wdenk43d96162003-03-06 00:02:04 +00001755 Offset of the bootmode word in DPRAM used by post
1756 (Power On Self Tests). This definition overrides
1757 #define'd default value in commproc.h resp.
1758 cpm_8260.h.
wdenkea909b72002-11-21 23:11:29 +00001759
stroese1d49b1f2003-05-23 11:39:05 +00001760- CFG_PCI_SLV_MEM_LOCAL, CFG_PCI_SLV_MEM_BUS, CFG_PICMR0_MASK_ATTRIB,
1761 CFG_PCI_MSTR0_LOCAL, CFG_PCIMSK0_MASK, CFG_PCI_MSTR1_LOCAL,
1762 CFG_PCIMSK1_MASK, CFG_PCI_MSTR_MEM_LOCAL, CFG_PCI_MSTR_MEM_BUS,
1763 CFG_CPU_PCI_MEM_START, CFG_PCI_MSTR_MEM_SIZE, CFG_POCMR0_MASK_ATTRIB,
1764 CFG_PCI_MSTR_MEMIO_LOCAL, CFG_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
1765 CFG_PCI_MSTR_MEMIO_SIZE, CFG_POCMR1_MASK_ATTRIB, CFG_PCI_MSTR_IO_LOCAL,
1766 CFG_PCI_MSTR_IO_BUS, CFG_CPU_PCI_IO_START, CFG_PCI_MSTR_IO_SIZE,
wdenk5d232d02003-05-22 22:52:13 +00001767 CFG_POCMR2_MASK_ATTRIB: (MPC826x only)
1768 Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
1769
wdenkc6097192002-11-03 00:24:07 +00001770Building the Software:
1771======================
1772
1773Building U-Boot has been tested in native PPC environments (on a
1774PowerBook G3 running LinuxPPC 2000) and in cross environments
1775(running RedHat 6.x and 7.x Linux on x86, Solaris 2.6 on a SPARC, and
1776NetBSD 1.5 on x86).
1777
1778If you are not using a native PPC environment, it is assumed that you
1779have the GNU cross compiling tools available in your path and named
1780with a prefix of "powerpc-linux-". If this is not the case, (e.g. if
1781you are using Monta Vista's Hard Hat Linux CDK 1.2) you must change
1782the definition of CROSS_COMPILE in Makefile. For HHL on a 4xx CPU,
1783change it to:
1784
1785 CROSS_COMPILE = ppc_4xx-
1786
1787
1788U-Boot is intended to be simple to build. After installing the
1789sources you must configure U-Boot for one specific board type. This
1790is done by typing:
1791
1792 make NAME_config
1793
1794where "NAME_config" is the name of one of the existing
1795configurations; the following names are supported:
1796
1797 ADCIOP_config GTH_config TQM850L_config
1798 ADS860_config IP860_config TQM855L_config
1799 AR405_config IVML24_config TQM860L_config
1800 CANBT_config IVMS8_config WALNUT405_config
1801 CPCI405_config LANTEC_config cogent_common_config
1802 CPCIISER4_config MBX_config cogent_mpc8260_config
1803 CU824_config MBX860T_config cogent_mpc8xx_config
1804 ESTEEM192E_config RPXlite_config hermes_config
1805 ETX094_config RPXsuper_config hymod_config
1806 FADS823_config SM850_config lwmon_config
1807 FADS850SAR_config SPD823TS_config pcu_e_config
1808 FADS860T_config SXNI855T_config rsdproto_config
1809 FPS850L_config Sandpoint8240_config sbc8260_config
1810 GENIETV_config TQM823L_config PIP405_config
wdenk384ae022002-11-05 00:17:55 +00001811 GEN860T_config EBONY_config FPS860L_config
wdenk7f70e852003-05-20 14:25:27 +00001812 ELPT860_config cmi_mpc5xx_config NETVIA_config
wdenk2abbe072003-06-16 23:50:08 +00001813 at91rm9200dk_config
wdenkc6097192002-11-03 00:24:07 +00001814
1815Note: for some board special configuration names may exist; check if
1816 additional information is available from the board vendor; for
1817 instance, the TQM8xxL systems run normally at 50 MHz and use a
1818 SCC for 10baseT ethernet; there are also systems with 80 MHz
1819 CPU clock, and an optional Fast Ethernet module is available
1820 for CPU's with FEC. You can select such additional "features"
1821 when chosing the configuration, i. e.
1822
1823 make TQM860L_config
1824 - will configure for a plain TQM860L, i. e. 50MHz, no FEC
1825
1826 make TQM860L_FEC_config
1827 - will configure for a TQM860L at 50MHz with FEC for ethernet
1828
1829 make TQM860L_80MHz_config
1830 - will configure for a TQM860L at 80 MHz, with normal 10baseT
1831 interface
1832
1833 make TQM860L_FEC_80MHz_config
1834 - will configure for a TQM860L at 80 MHz with FEC for ethernet
1835
1836 make TQM823L_LCD_config
1837 - will configure for a TQM823L with U-Boot console on LCD
1838
1839 make TQM823L_LCD_80MHz_config
1840 - will configure for a TQM823L at 80 MHz with U-Boot console on LCD
1841
1842 etc.
1843
1844
1845
wdenk24ee89b2002-11-03 17:56:27 +00001846Finally, type "make all", and you should get some working U-Boot
wdenkc6097192002-11-03 00:24:07 +00001847images ready for downlod to / installation on your system:
1848
1849- "u-boot.bin" is a raw binary image
1850- "u-boot" is an image in ELF binary format
1851- "u-boot.srec" is in Motorola S-Record format
1852
1853
1854Please be aware that the Makefiles assume you are using GNU make, so
1855for instance on NetBSD you might need to use "gmake" instead of
1856native "make".
1857
1858
1859If the system board that you have is not listed, then you will need
1860to port U-Boot to your hardware platform. To do this, follow these
1861steps:
1862
18631. Add a new configuration option for your board to the toplevel
wdenk85ec0bc2003-03-31 16:34:49 +00001864 "Makefile" and to the "MAKEALL" script, using the existing
1865 entries as examples. Note that here and at many other places
1866 boards and other names are listed alphabetically sorted. Please
1867 keep this order.
wdenkc6097192002-11-03 00:24:07 +000018682. Create a new directory to hold your board specific code. Add any
wdenk85ec0bc2003-03-31 16:34:49 +00001869 files you need. In your board directory, you will need at least
1870 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
18713. Create a new configuration file "include/configs/<board>.h" for
1872 your board
wdenkc6097192002-11-03 00:24:07 +000018733. If you're porting U-Boot to a new CPU, then also create a new
1874 directory to hold your CPU specific code. Add any files you need.
wdenk85ec0bc2003-03-31 16:34:49 +000018754. Run "make <board>_config" with your new name.
wdenkc6097192002-11-03 00:24:07 +000018765. Type "make", and you should get a working "u-boot.srec" file
1877 to be installed on your target system.
wdenk85ec0bc2003-03-31 16:34:49 +000018786. Debug and solve any problems that might arise.
wdenkc6097192002-11-03 00:24:07 +00001879 [Of course, this last step is much harder than it sounds.]
1880
1881
1882Testing of U-Boot Modifications, Ports to New Hardware, etc.:
1883==============================================================
1884
1885If you have modified U-Boot sources (for instance added a new board
1886or support for new devices, a new CPU, etc.) you are expected to
1887provide feedback to the other developers. The feedback normally takes
1888the form of a "patch", i. e. a context diff against a certain (latest
1889official or latest in CVS) version of U-Boot sources.
1890
1891But before you submit such a patch, please verify that your modifi-
1892cation did not break existing code. At least make sure that *ALL* of
1893the supported boards compile WITHOUT ANY compiler warnings. To do so,
1894just run the "MAKEALL" script, which will configure and build U-Boot
1895for ALL supported system. Be warned, this will take a while. You can
1896select which (cross) compiler to use py passing a `CROSS_COMPILE'
1897environment variable to the script, i. e. to use the cross tools from
1898MontaVista's Hard Hat Linux you can type
1899
1900 CROSS_COMPILE=ppc_8xx- MAKEALL
1901
1902or to build on a native PowerPC system you can type
1903
1904 CROSS_COMPILE=' ' MAKEALL
1905
1906See also "U-Boot Porting Guide" below.
1907
1908
1909
1910Monitor Commands - Overview:
1911============================
1912
1913go - start application at address 'addr'
1914run - run commands in an environment variable
1915bootm - boot application image from memory
1916bootp - boot image via network using BootP/TFTP protocol
1917tftpboot- boot image via network using TFTP protocol
1918 and env variables "ipaddr" and "serverip"
1919 (and eventually "gatewayip")
1920rarpboot- boot image via network using RARP/TFTP protocol
1921diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
1922loads - load S-Record file over serial line
1923loadb - load binary file over serial line (kermit mode)
1924md - memory display
1925mm - memory modify (auto-incrementing)
1926nm - memory modify (constant address)
1927mw - memory write (fill)
1928cp - memory copy
1929cmp - memory compare
1930crc32 - checksum calculation
1931imd - i2c memory display
1932imm - i2c memory modify (auto-incrementing)
1933inm - i2c memory modify (constant address)
1934imw - i2c memory write (fill)
1935icrc32 - i2c checksum calculation
1936iprobe - probe to discover valid I2C chip addresses
1937iloop - infinite loop on address range
1938isdram - print SDRAM configuration information
1939sspi - SPI utility commands
1940base - print or set address offset
1941printenv- print environment variables
1942setenv - set environment variables
1943saveenv - save environment variables to persistent storage
1944protect - enable or disable FLASH write protection
1945erase - erase FLASH memory
1946flinfo - print FLASH memory information
1947bdinfo - print Board Info structure
1948iminfo - print header information for application image
1949coninfo - print console devices and informations
1950ide - IDE sub-system
1951loop - infinite loop on address range
1952mtest - simple RAM test
1953icache - enable or disable instruction cache
1954dcache - enable or disable data cache
1955reset - Perform RESET of the CPU
1956echo - echo args to console
1957version - print monitor version
1958help - print online help
1959? - alias for 'help'
1960
1961
1962Monitor Commands - Detailed Description:
1963========================================
1964
1965TODO.
1966
1967For now: just type "help <command>".
1968
1969
1970Environment Variables:
1971======================
1972
1973U-Boot supports user configuration using Environment Variables which
1974can be made persistent by saving to Flash memory.
1975
1976Environment Variables are set using "setenv", printed using
1977"printenv", and saved to Flash using "saveenv". Using "setenv"
1978without a value can be used to delete a variable from the
1979environment. As long as you don't save the environment you are
1980working with an in-memory copy. In case the Flash area containing the
1981environment is erased by accident, a default environment is provided.
1982
1983Some configuration options can be set using Environment Variables:
1984
1985 baudrate - see CONFIG_BAUDRATE
1986
1987 bootdelay - see CONFIG_BOOTDELAY
1988
1989 bootcmd - see CONFIG_BOOTCOMMAND
1990
1991 bootargs - Boot arguments when booting an RTOS image
1992
1993 bootfile - Name of the image to load with TFTP
1994
1995 autoload - if set to "no" (any string beginning with 'n'),
1996 "bootp" will just load perform a lookup of the
1997 configuration from the BOOTP server, but not try to
1998 load any image using TFTP
1999
2000 autostart - if set to "yes", an image loaded using the "bootp",
2001 "rarpboot", "tftpboot" or "diskboot" commands will
2002 be automatically started (by internally calling
2003 "bootm")
2004
wdenk4a6fd342003-04-12 23:38:12 +00002005 If set to "no", a standalone image passed to the
2006 "bootm" command will be copied to the load address
2007 (and eventually uncompressed), but NOT be started.
2008 This can be used to load and uncompress arbitrary
2009 data.
2010
wdenkc6097192002-11-03 00:24:07 +00002011 initrd_high - restrict positioning of initrd images:
2012 If this variable is not set, initrd images will be
2013 copied to the highest possible address in RAM; this
2014 is usually what you want since it allows for
2015 maximum initrd size. If for some reason you want to
2016 make sure that the initrd image is loaded below the
2017 CFG_BOOTMAPSZ limit, you can set this environment
2018 variable to a value of "no" or "off" or "0".
2019 Alternatively, you can set it to a maximum upper
2020 address to use (U-Boot will still check that it
2021 does not overwrite the U-Boot stack and data).
2022
2023 For instance, when you have a system with 16 MB
2024 RAM, and want to reseve 4 MB from use by Linux,
2025 you can do this by adding "mem=12M" to the value of
2026 the "bootargs" variable. However, now you must make
2027 sure, that the initrd image is placed in the first
2028 12 MB as well - this can be done with
2029
2030 setenv initrd_high 00c00000
2031
wdenk38b99262003-05-23 23:18:21 +00002032 If you set initrd_high to 0xFFFFFFFF, this is an
2033 indication to U-Boot that all addresses are legal
2034 for the Linux kernel, including addresses in flash
2035 memory. In this case U-Boot will NOT COPY the
2036 ramdisk at all. This may be useful to reduce the
2037 boot time on your system, but requires that this
2038 feature is supported by your Linux kernel.
2039
wdenkc6097192002-11-03 00:24:07 +00002040 ipaddr - IP address; needed for tftpboot command
2041
2042 loadaddr - Default load address for commands like "bootp",
wdenkdc7c9a12003-03-26 06:55:25 +00002043 "rarpboot", "tftpboot", "loadb" or "diskboot"
wdenkc6097192002-11-03 00:24:07 +00002044
2045 loads_echo - see CONFIG_LOADS_ECHO
2046
2047 serverip - TFTP server IP address; needed for tftpboot command
2048
2049 bootretry - see CONFIG_BOOT_RETRY_TIME
2050
2051 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
2052
2053 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
2054
2055
2056The following environment variables may be used and automatically
2057updated by the network boot commands ("bootp" and "rarpboot"),
2058depending the information provided by your boot server:
2059
2060 bootfile - see above
2061 dnsip - IP address of your Domain Name Server
2062 gatewayip - IP address of the Gateway (Router) to use
2063 hostname - Target hostname
2064 ipaddr - see above
2065 netmask - Subnet Mask
2066 rootpath - Pathname of the root filesystem on the NFS server
2067 serverip - see above
2068
2069
2070There are two special Environment Variables:
2071
2072 serial# - contains hardware identification information such
2073 as type string and/or serial number
2074 ethaddr - Ethernet address
2075
2076These variables can be set only once (usually during manufacturing of
2077the board). U-Boot refuses to delete or overwrite these variables
2078once they have been set once.
2079
2080
stroesec1551ea2003-04-04 15:53:41 +00002081Further special Environment Variables:
2082
2083 ver - Contains the U-Boot version string as printed
2084 with the "version" command. This variable is
2085 readonly (see CONFIG_VERSION_VARIABLE).
2086
2087
wdenkc6097192002-11-03 00:24:07 +00002088Please note that changes to some configuration parameters may take
2089only effect after the next boot (yes, that's just like Windoze :-).
2090
2091
wdenkf07771c2003-05-28 08:06:31 +00002092Command Line Parsing:
2093=====================
2094
2095There are two different command line parsers available with U-Boot:
2096the old "simple" one, and the much more pwerful "hush" shell:
2097
2098Old, simple command line parser:
2099--------------------------------
2100
2101- supports environment variables (through setenv / saveenv commands)
2102- several commands on one line, separated by ';'
2103- variable substitution using "... $(name) ..." syntax
2104- special characters ('$', ';') can be escaped by prefixing with '\',
2105 for example:
2106 setenv bootcmd bootm \$(address)
2107- You can also escape text by enclosing in single apostrophes, for example:
2108 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
2109
2110Hush shell:
2111-----------
2112
2113- similar to Bourne shell, with control structures like
2114 if...then...else...fi, for...do...done; while...do...done,
2115 until...do...done, ...
2116- supports environment ("global") variables (through setenv / saveenv
2117 commands) and local shell variables (through standard shell syntax
2118 "name=value"); only environment variables can be used with "run"
2119 command
2120
2121General rules:
2122--------------
2123
2124(1) If a command line (or an environment variable executed by a "run"
2125 command) contains several commands separated by semicolon, and
2126 one of these commands fails, then the remaining commands will be
2127 executed anyway.
2128
2129(2) If you execute several variables with one call to run (i. e.
2130 calling run with a list af variables as arguments), any failing
2131 command will cause "run" to terminate, i. e. the remaining
2132 variables are not executed.
2133
wdenkc6097192002-11-03 00:24:07 +00002134Note for Redundant Ethernet Interfaces:
2135=======================================
2136
2137Some boards come with redundand ethernet interfaces; U-Boot supports
2138such configurations and is capable of automatic selection of a
2139"working" interface when needed. MAC assignemnt works as follows:
2140
2141Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
2142MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
2143"eth1addr" (=>eth1), "eth2addr", ...
2144
2145If the network interface stores some valid MAC address (for instance
2146in SROM), this is used as default address if there is NO correspon-
2147ding setting in the environment; if the corresponding environment
2148variable is set, this overrides the settings in the card; that means:
2149
2150o If the SROM has a valid MAC address, and there is no address in the
2151 environment, the SROM's address is used.
2152
2153o If there is no valid address in the SROM, and a definition in the
2154 environment exists, then the value from the environment variable is
2155 used.
2156
2157o If both the SROM and the environment contain a MAC address, and
2158 both addresses are the same, this MAC address is used.
2159
2160o If both the SROM and the environment contain a MAC address, and the
2161 addresses differ, the value from the environment is used and a
2162 warning is printed.
2163
2164o If neither SROM nor the environment contain a MAC address, an error
2165 is raised.
2166
2167
2168
2169Image Formats:
2170==============
2171
2172The "boot" commands of this monitor operate on "image" files which
2173can be basicly anything, preceeded by a special header; see the
2174definitions in include/image.h for details; basicly, the header
2175defines the following image properties:
2176
2177* Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
2178 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
wdenk7f70e852003-05-20 14:25:27 +00002179 LynxOS, pSOS, QNX, RTEMS, ARTOS;
2180 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, ARTOS).
wdenkc6097192002-11-03 00:24:07 +00002181* Target CPU Architecture (Provisions for Alpha, ARM, Intel x86,
2182 IA64, MIPS, MIPS, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
2183 Currently supported: PowerPC).
2184* Compression Type (Provisions for uncompressed, gzip, bzip2;
2185 Currently supported: uncompressed, gzip).
2186* Load Address
2187* Entry Point
2188* Image Name
2189* Image Timestamp
2190
2191The header is marked by a special Magic Number, and both the header
2192and the data portions of the image are secured against corruption by
2193CRC32 checksums.
2194
2195
2196Linux Support:
2197==============
2198
2199Although U-Boot should support any OS or standalone application
2200easily, Linux has always been in the focus during the design of
2201U-Boot.
2202
2203U-Boot includes many features that so far have been part of some
2204special "boot loader" code within the Linux kernel. Also, any
2205"initrd" images to be used are no longer part of one big Linux image;
2206instead, kernel and "initrd" are separate images. This implementation
2207serves serveral purposes:
2208
2209- the same features can be used for other OS or standalone
2210 applications (for instance: using compressed images to reduce the
2211 Flash memory footprint)
2212
2213- it becomes much easier to port new Linux kernel versions because
2214 lots of low-level, hardware dependend stuff are done by U-Boot
2215
2216- the same Linux kernel image can now be used with different "initrd"
2217 images; of course this also means that different kernel images can
2218 be run with the same "initrd". This makes testing easier (you don't
2219 have to build a new "zImage.initrd" Linux image when you just
2220 change a file in your "initrd"). Also, a field-upgrade of the
2221 software is easier now.
2222
2223
2224Linux HOWTO:
2225============
2226
2227Porting Linux to U-Boot based systems:
2228---------------------------------------
2229
2230U-Boot cannot save you from doing all the necessary modifications to
2231configure the Linux device drivers for use with your target hardware
2232(no, we don't intend to provide a full virtual machine interface to
2233Linux :-).
2234
2235But now you can ignore ALL boot loader code (in arch/ppc/mbxboot).
2236
2237Just make sure your machine specific header file (for instance
2238include/asm-ppc/tqm8xx.h) includes the same definition of the Board
2239Information structure as we define in include/u-boot.h, and make
2240sure that your definition of IMAP_ADDR uses the same value as your
2241U-Boot configuration in CFG_IMMR.
2242
2243
2244Configuring the Linux kernel:
2245-----------------------------
2246
2247No specific requirements for U-Boot. Make sure you have some root
2248device (initial ramdisk, NFS) for your target system.
2249
2250
2251Building a Linux Image:
2252-----------------------
2253
wdenk24ee89b2002-11-03 17:56:27 +00002254With U-Boot, "normal" build targets like "zImage" or "bzImage" are
2255not used. If you use recent kernel source, a new build target
2256"uImage" will exist which automatically builds an image usable by
2257U-Boot. Most older kernels also have support for a "pImage" target,
2258which was introduced for our predecessor project PPCBoot and uses a
2259100% compatible format.
wdenkc6097192002-11-03 00:24:07 +00002260
2261Example:
2262
2263 make TQM850L_config
2264 make oldconfig
2265 make dep
wdenk24ee89b2002-11-03 17:56:27 +00002266 make uImage
wdenkc6097192002-11-03 00:24:07 +00002267
wdenk24ee89b2002-11-03 17:56:27 +00002268The "uImage" build target uses a special tool (in 'tools/mkimage') to
2269encapsulate a compressed Linux kernel image with header information,
2270CRC32 checksum etc. for use with U-Boot. This is what we are doing:
wdenkc6097192002-11-03 00:24:07 +00002271
wdenk24ee89b2002-11-03 17:56:27 +00002272* build a standard "vmlinux" kernel image (in ELF binary format):
wdenkc6097192002-11-03 00:24:07 +00002273
wdenk24ee89b2002-11-03 17:56:27 +00002274* convert the kernel into a raw binary image:
2275
2276 ${CROSS_COMPILE}-objcopy -O binary \
2277 -R .note -R .comment \
2278 -S vmlinux linux.bin
2279
2280* compress the binary image:
2281
2282 gzip -9 linux.bin
2283
2284* package compressed binary image for U-Boot:
2285
2286 mkimage -A ppc -O linux -T kernel -C gzip \
2287 -a 0 -e 0 -n "Linux Kernel Image" \
2288 -d linux.bin.gz uImage
2289
2290
2291The "mkimage" tool can also be used to create ramdisk images for use
2292with U-Boot, either separated from the Linux kernel image, or
2293combined into one file. "mkimage" encapsulates the images with a 64
2294byte header containing information about target architecture,
2295operating system, image type, compression method, entry points, time
2296stamp, CRC32 checksums, etc.
2297
2298"mkimage" can be called in two ways: to verify existing images and
2299print the header information, or to build new images.
2300
2301In the first form (with "-l" option) mkimage lists the information
2302contained in the header of an existing U-Boot image; this includes
wdenkc6097192002-11-03 00:24:07 +00002303checksum verification:
2304
2305 tools/mkimage -l image
2306 -l ==> list image header information
2307
2308The second form (with "-d" option) is used to build a U-Boot image
2309from a "data file" which is used as image payload:
2310
2311 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
2312 -n name -d data_file image
2313 -A ==> set architecture to 'arch'
2314 -O ==> set operating system to 'os'
2315 -T ==> set image type to 'type'
2316 -C ==> set compression type 'comp'
2317 -a ==> set load address to 'addr' (hex)
2318 -e ==> set entry point to 'ep' (hex)
2319 -n ==> set image name to 'name'
2320 -d ==> use image data from 'datafile'
2321
2322Right now, all Linux kernels use the same load address (0x00000000),
2323but the entry point address depends on the kernel version:
2324
2325- 2.2.x kernels have the entry point at 0x0000000C,
wdenk24ee89b2002-11-03 17:56:27 +00002326- 2.3.x and later kernels have the entry point at 0x00000000.
wdenkc6097192002-11-03 00:24:07 +00002327
2328So a typical call to build a U-Boot image would read:
2329
wdenk24ee89b2002-11-03 17:56:27 +00002330 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2331 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
2332 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz \
2333 > examples/uImage.TQM850L
2334 Image Name: 2.4.4 kernel for TQM850L
wdenkc6097192002-11-03 00:24:07 +00002335 Created: Wed Jul 19 02:34:59 2000
2336 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2337 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2338 Load Address: 0x00000000
wdenk24ee89b2002-11-03 17:56:27 +00002339 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00002340
2341To verify the contents of the image (or check for corruption):
2342
wdenk24ee89b2002-11-03 17:56:27 +00002343 -> tools/mkimage -l examples/uImage.TQM850L
2344 Image Name: 2.4.4 kernel for TQM850L
wdenkc6097192002-11-03 00:24:07 +00002345 Created: Wed Jul 19 02:34:59 2000
2346 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2347 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
2348 Load Address: 0x00000000
wdenk24ee89b2002-11-03 17:56:27 +00002349 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00002350
2351NOTE: for embedded systems where boot time is critical you can trade
2352speed for memory and install an UNCOMPRESSED image instead: this
2353needs more space in Flash, but boots much faster since it does not
2354need to be uncompressed:
2355
wdenk24ee89b2002-11-03 17:56:27 +00002356 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux.gz
2357 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
2358 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
2359 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/ppc/coffboot/vmlinux \
2360 > examples/uImage.TQM850L-uncompressed
2361 Image Name: 2.4.4 kernel for TQM850L
wdenkc6097192002-11-03 00:24:07 +00002362 Created: Wed Jul 19 02:34:59 2000
2363 Image Type: PowerPC Linux Kernel Image (uncompressed)
2364 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
2365 Load Address: 0x00000000
wdenk24ee89b2002-11-03 17:56:27 +00002366 Entry Point: 0x00000000
wdenkc6097192002-11-03 00:24:07 +00002367
2368
2369Similar you can build U-Boot images from a 'ramdisk.image.gz' file
2370when your kernel is intended to use an initial ramdisk:
2371
2372 -> tools/mkimage -n 'Simple Ramdisk Image' \
2373 > -A ppc -O linux -T ramdisk -C gzip \
2374 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
2375 Image Name: Simple Ramdisk Image
2376 Created: Wed Jan 12 14:01:50 2000
2377 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2378 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
2379 Load Address: 0x00000000
2380 Entry Point: 0x00000000
2381
2382
2383Installing a Linux Image:
2384-------------------------
2385
2386To downloading a U-Boot image over the serial (console) interface,
2387you must convert the image to S-Record format:
2388
2389 objcopy -I binary -O srec examples/image examples/image.srec
2390
2391The 'objcopy' does not understand the information in the U-Boot
2392image header, so the resulting S-Record file will be relative to
2393address 0x00000000. To load it to a given address, you need to
2394specify the target address as 'offset' parameter with the 'loads'
2395command.
2396
2397Example: install the image to address 0x40100000 (which on the
2398TQM8xxL is in the first Flash bank):
2399
2400 => erase 40100000 401FFFFF
2401
2402 .......... done
2403 Erased 8 sectors
2404
2405 => loads 40100000
2406 ## Ready for S-Record download ...
2407 ~>examples/image.srec
2408 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
2409 ...
2410 15989 15990 15991 15992
2411 [file transfer complete]
2412 [connected]
2413 ## Start Addr = 0x00000000
2414
2415
2416You can check the success of the download using the 'iminfo' command;
2417this includes a checksum verification so you can be sure no data
2418corruption happened:
2419
2420 => imi 40100000
2421
2422 ## Checking Image at 40100000 ...
2423 Image Name: 2.2.13 for initrd on TQM850L
2424 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2425 Data Size: 335725 Bytes = 327 kB = 0 MB
2426 Load Address: 00000000
2427 Entry Point: 0000000c
2428 Verifying Checksum ... OK
2429
2430
2431
2432Boot Linux:
2433-----------
2434
2435The "bootm" command is used to boot an application that is stored in
2436memory (RAM or Flash). In case of a Linux kernel image, the contents
2437of the "bootargs" environment variable is passed to the kernel as
2438parameters. You can check and modify this variable using the
2439"printenv" and "setenv" commands:
2440
2441
2442 => printenv bootargs
2443 bootargs=root=/dev/ram
2444
2445 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2446
2447 => printenv bootargs
2448 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2449
2450 => bootm 40020000
2451 ## Booting Linux kernel at 40020000 ...
2452 Image Name: 2.2.13 for NFS on TQM850L
2453 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2454 Data Size: 381681 Bytes = 372 kB = 0 MB
2455 Load Address: 00000000
2456 Entry Point: 0000000c
2457 Verifying Checksum ... OK
2458 Uncompressing Kernel Image ... OK
2459 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
2460 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
2461 time_init: decrementer frequency = 187500000/60
2462 Calibrating delay loop... 49.77 BogoMIPS
2463 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
2464 ...
2465
2466If you want to boot a Linux kernel with initial ram disk, you pass
2467the memory addreses of both the kernel and the initrd image (PPBCOOT
2468format!) to the "bootm" command:
2469
2470 => imi 40100000 40200000
2471
2472 ## Checking Image at 40100000 ...
2473 Image Name: 2.2.13 for initrd on TQM850L
2474 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2475 Data Size: 335725 Bytes = 327 kB = 0 MB
2476 Load Address: 00000000
2477 Entry Point: 0000000c
2478 Verifying Checksum ... OK
2479
2480 ## Checking Image at 40200000 ...
2481 Image Name: Simple Ramdisk Image
2482 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2483 Data Size: 566530 Bytes = 553 kB = 0 MB
2484 Load Address: 00000000
2485 Entry Point: 00000000
2486 Verifying Checksum ... OK
2487
2488 => bootm 40100000 40200000
2489 ## Booting Linux kernel at 40100000 ...
2490 Image Name: 2.2.13 for initrd on TQM850L
2491 Image Type: PowerPC Linux Kernel Image (gzip compressed)
2492 Data Size: 335725 Bytes = 327 kB = 0 MB
2493 Load Address: 00000000
2494 Entry Point: 0000000c
2495 Verifying Checksum ... OK
2496 Uncompressing Kernel Image ... OK
2497 ## Loading RAMDisk Image at 40200000 ...
2498 Image Name: Simple Ramdisk Image
2499 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
2500 Data Size: 566530 Bytes = 553 kB = 0 MB
2501 Load Address: 00000000
2502 Entry Point: 00000000
2503 Verifying Checksum ... OK
2504 Loading Ramdisk ... OK
2505 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
2506 Boot arguments: root=/dev/ram
2507 time_init: decrementer frequency = 187500000/60
2508 Calibrating delay loop... 49.77 BogoMIPS
2509 ...
2510 RAMDISK: Compressed image found at block 0
2511 VFS: Mounted root (ext2 filesystem).
2512
2513 bash#
2514
wdenk6069ff22003-02-28 00:49:47 +00002515More About U-Boot Image Types:
2516------------------------------
2517
2518U-Boot supports the following image types:
2519
2520 "Standalone Programs" are directly runnable in the environment
2521 provided by U-Boot; it is expected that (if they behave
2522 well) you can continue to work in U-Boot after return from
2523 the Standalone Program.
2524 "OS Kernel Images" are usually images of some Embedded OS which
2525 will take over control completely. Usually these programs
2526 will install their own set of exception handlers, device
2527 drivers, set up the MMU, etc. - this means, that you cannot
2528 expect to re-enter U-Boot except by resetting the CPU.
2529 "RAMDisk Images" are more or less just data blocks, and their
2530 parameters (address, size) are passed to an OS kernel that is
2531 being started.
2532 "Multi-File Images" contain several images, typically an OS
2533 (Linux) kernel image and one or more data images like
2534 RAMDisks. This construct is useful for instance when you want
2535 to boot over the network using BOOTP etc., where the boot
2536 server provides just a single image file, but you want to get
2537 for instance an OS kernel and a RAMDisk image.
stroesec1551ea2003-04-04 15:53:41 +00002538
wdenk6069ff22003-02-28 00:49:47 +00002539 "Multi-File Images" start with a list of image sizes, each
2540 image size (in bytes) specified by an "uint32_t" in network
2541 byte order. This list is terminated by an "(uint32_t)0".
2542 Immediately after the terminating 0 follow the images, one by
2543 one, all aligned on "uint32_t" boundaries (size rounded up to
2544 a multiple of 4 bytes).
stroesec1551ea2003-04-04 15:53:41 +00002545
wdenk6069ff22003-02-28 00:49:47 +00002546 "Firmware Images" are binary images containing firmware (like
2547 U-Boot or FPGA images) which usually will be programmed to
2548 flash memory.
stroesec1551ea2003-04-04 15:53:41 +00002549
wdenk6069ff22003-02-28 00:49:47 +00002550 "Script files" are command sequences that will be executed by
2551 U-Boot's command interpreter; this feature is especially
2552 useful when you configure U-Boot to use a real shell (hush)
2553 as command interpreter.
2554
wdenkc6097192002-11-03 00:24:07 +00002555
2556Standalone HOWTO:
2557=================
2558
2559One of the features of U-Boot is that you can dynamically load and
2560run "standalone" applications, which can use some resources of
2561U-Boot like console I/O functions or interrupt services.
2562
2563Two simple examples are included with the sources:
2564
2565"Hello World" Demo:
2566-------------------
2567
2568'examples/hello_world.c' contains a small "Hello World" Demo
2569application; it is automatically compiled when you build U-Boot.
2570It's configured to run at address 0x00040004, so you can play with it
2571like that:
2572
2573 => loads
2574 ## Ready for S-Record download ...
2575 ~>examples/hello_world.srec
2576 1 2 3 4 5 6 7 8 9 10 11 ...
2577 [file transfer complete]
2578 [connected]
2579 ## Start Addr = 0x00040004
2580
2581 => go 40004 Hello World! This is a test.
2582 ## Starting application at 0x00040004 ...
2583 Hello World
2584 argc = 7
2585 argv[0] = "40004"
2586 argv[1] = "Hello"
2587 argv[2] = "World!"
2588 argv[3] = "This"
2589 argv[4] = "is"
2590 argv[5] = "a"
2591 argv[6] = "test."
2592 argv[7] = "<NULL>"
2593 Hit any key to exit ...
2594
2595 ## Application terminated, rc = 0x0
2596
2597Another example, which demonstrates how to register a CPM interrupt
2598handler with the U-Boot code, can be found in 'examples/timer.c'.
2599Here, a CPM timer is set up to generate an interrupt every second.
2600The interrupt service routine is trivial, just printing a '.'
2601character, but this is just a demo program. The application can be
2602controlled by the following keys:
2603
2604 ? - print current values og the CPM Timer registers
2605 b - enable interrupts and start timer
2606 e - stop timer and disable interrupts
2607 q - quit application
2608
2609 => loads
2610 ## Ready for S-Record download ...
2611 ~>examples/timer.srec
2612 1 2 3 4 5 6 7 8 9 10 11 ...
2613 [file transfer complete]
2614 [connected]
2615 ## Start Addr = 0x00040004
2616
2617 => go 40004
2618 ## Starting application at 0x00040004 ...
2619 TIMERS=0xfff00980
2620 Using timer 1
2621 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
2622
2623Hit 'b':
2624 [q, b, e, ?] Set interval 1000000 us
2625 Enabling timer
2626Hit '?':
2627 [q, b, e, ?] ........
2628 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
2629Hit '?':
2630 [q, b, e, ?] .
2631 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
2632Hit '?':
2633 [q, b, e, ?] .
2634 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
2635Hit '?':
2636 [q, b, e, ?] .
2637 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
2638Hit 'e':
2639 [q, b, e, ?] ...Stopping timer
2640Hit 'q':
2641 [q, b, e, ?] ## Application terminated, rc = 0x0
2642
2643
wdenk85ec0bc2003-03-31 16:34:49 +00002644
2645Minicom warning:
2646================
2647
2648Over time, many people have reported problems when trying to used the
wdenkf07771c2003-05-28 08:06:31 +00002649"minicom" terminal emulation program for serial download. I (wd)
2650consider minicom to be broken, and recommend not to use it. Under
2651Unix, I recommend to use C-Kermit for general purpose use (and
wdenk85ec0bc2003-03-31 16:34:49 +00002652especially for kermit binary protocol download ("loadb" command), and
2653use "cu" for S-Record download ("loads" command).
2654
wdenk52f52c12003-06-19 23:04:19 +00002655Nevertheless, if you absolutely want to use it try adding this
2656configuration to your "File transfer protocols" section:
2657
2658 Name Program Name U/D FullScr IO-Red. Multi
2659 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
2660 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
2661
2662
wdenkc6097192002-11-03 00:24:07 +00002663NetBSD Notes:
2664=============
2665
2666Starting at version 0.9.2, U-Boot supports NetBSD both as host
2667(build U-Boot) and target system (boots NetBSD/mpc8xx).
2668
2669Building requires a cross environment; it is known to work on
2670NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
2671need gmake since the Makefiles are not compatible with BSD make).
2672Note that the cross-powerpc package does not install include files;
2673attempting to build U-Boot will fail because <machine/ansi.h> is
2674missing. This file has to be installed and patched manually:
2675
2676 # cd /usr/pkg/cross/powerpc-netbsd/include
2677 # mkdir powerpc
2678 # ln -s powerpc machine
2679 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
2680 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
2681
2682Native builds *don't* work due to incompatibilities between native
2683and U-Boot include files.
2684
2685Booting assumes that (the first part of) the image booted is a
2686stage-2 loader which in turn loads and then invokes the kernel
2687proper. Loader sources will eventually appear in the NetBSD source
2688tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
2689meantime, send mail to bruno@exet-ag.de and/or wd@denx.de for
2690details.
2691
2692
2693Implementation Internals:
2694=========================
2695
2696The following is not intended to be a complete description of every
2697implementation detail. However, it should help to understand the
2698inner workings of U-Boot and make it easier to port it to custom
2699hardware.
2700
2701
2702Initial Stack, Global Data:
2703---------------------------
2704
2705The implementation of U-Boot is complicated by the fact that U-Boot
2706starts running out of ROM (flash memory), usually without access to
2707system RAM (because the memory controller is not initialized yet).
2708This means that we don't have writable Data or BSS segments, and BSS
2709is not initialized as zero. To be able to get a C environment working
2710at all, we have to allocate at least a minimal stack. Implementation
2711options for this are defined and restricted by the CPU used: Some CPU
2712models provide on-chip memory (like the IMMR area on MPC8xx and
2713MPC826x processors), on others (parts of) the data cache can be
2714locked as (mis-) used as memory, etc.
2715
wdenk43d96162003-03-06 00:02:04 +00002716 Chris Hallinan posted a good summy of these issues to the
2717 u-boot-users mailing list:
2718
2719 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
2720 From: "Chris Hallinan" <clh@net1plus.com>
2721 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
2722 ...
2723
2724 Correct me if I'm wrong, folks, but the way I understand it
2725 is this: Using DCACHE as initial RAM for Stack, etc, does not
2726 require any physical RAM backing up the cache. The cleverness
2727 is that the cache is being used as a temporary supply of
2728 necessary storage before the SDRAM controller is setup. It's
2729 beyond the scope of this list to expain the details, but you
2730 can see how this works by studying the cache architecture and
2731 operation in the architecture and processor-specific manuals.
2732
2733 OCM is On Chip Memory, which I believe the 405GP has 4K. It
2734 is another option for the system designer to use as an
2735 initial stack/ram area prior to SDRAM being available. Either
2736 option should work for you. Using CS 4 should be fine if your
2737 board designers haven't used it for something that would
2738 cause you grief during the initial boot! It is frequently not
2739 used.
2740
2741 CFG_INIT_RAM_ADDR should be somewhere that won't interfere
2742 with your processor/board/system design. The default value
2743 you will find in any recent u-boot distribution in
2744 Walnut405.h should work for you. I'd set it to a value larger
2745 than your SDRAM module. If you have a 64MB SDRAM module, set
2746 it above 400_0000. Just make sure your board has no resources
2747 that are supposed to respond to that address! That code in
2748 start.S has been around a while and should work as is when
2749 you get the config right.
2750
2751 -Chris Hallinan
2752 DS4.COM, Inc.
2753
wdenkc6097192002-11-03 00:24:07 +00002754It is essential to remember this, since it has some impact on the C
2755code for the initialization procedures:
2756
2757* Initialized global data (data segment) is read-only. Do not attempt
2758 to write it.
2759
2760* Do not use any unitialized global data (or implicitely initialized
2761 as zero data - BSS segment) at all - this is undefined, initiali-
2762 zation is performed later (when relocationg to RAM).
2763
2764* Stack space is very limited. Avoid big data buffers or things like
2765 that.
2766
2767Having only the stack as writable memory limits means we cannot use
2768normal global data to share information beween the code. But it
2769turned out that the implementation of U-Boot can be greatly
2770simplified by making a global data structure (gd_t) available to all
2771functions. We could pass a pointer to this data as argument to _all_
2772functions, but this would bloat the code. Instead we use a feature of
2773the GCC compiler (Global Register Variables) to share the data: we
2774place a pointer (gd) to the global data into a register which we
2775reserve for this purpose.
2776
2777When chosing a register for such a purpose we are restricted by the
2778relevant (E)ABI specifications for the current architecture, and by
2779GCC's implementation.
2780
2781For PowerPC, the following registers have specific use:
2782 R1: stack pointer
2783 R2: TOC pointer
2784 R3-R4: parameter passing and return values
2785 R5-R10: parameter passing
2786 R13: small data area pointer
2787 R30: GOT pointer
2788 R31: frame pointer
2789
2790 (U-Boot also uses R14 as internal GOT pointer.)
2791
2792 ==> U-Boot will use R29 to hold a pointer to the global data
2793
2794 Note: on PPC, we could use a static initializer (since the
2795 address of the global data structure is known at compile time),
2796 but it turned out that reserving a register results in somewhat
2797 smaller code - although the code savings are not that big (on
2798 average for all boards 752 bytes for the whole U-Boot image,
2799 624 text + 127 data).
2800
2801On ARM, the following registers are used:
2802
2803 R0: function argument word/integer result
2804 R1-R3: function argument word
2805 R9: GOT pointer
2806 R10: stack limit (used only if stack checking if enabled)
2807 R11: argument (frame) pointer
2808 R12: temporary workspace
2809 R13: stack pointer
2810 R14: link register
2811 R15: program counter
2812
2813 ==> U-Boot will use R8 to hold a pointer to the global data
2814
2815
2816
2817Memory Management:
2818------------------
2819
2820U-Boot runs in system state and uses physical addresses, i.e. the
2821MMU is not used either for address mapping nor for memory protection.
2822
2823The available memory is mapped to fixed addresses using the memory
2824controller. In this process, a contiguous block is formed for each
2825memory type (Flash, SDRAM, SRAM), even when it consists of several
2826physical memory banks.
2827
2828U-Boot is installed in the first 128 kB of the first Flash bank (on
2829TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
2830booting and sizing and initializing DRAM, the code relocates itself
2831to the upper end of DRAM. Immediately below the U-Boot code some
2832memory is reserved for use by malloc() [see CFG_MALLOC_LEN
2833configuration setting]. Below that, a structure with global Board
2834Info data is placed, followed by the stack (growing downward).
2835
2836Additionally, some exception handler code is copied to the low 8 kB
2837of DRAM (0x00000000 ... 0x00001FFF).
2838
2839So a typical memory configuration with 16 MB of DRAM could look like
2840this:
2841
2842 0x0000 0000 Exception Vector code
2843 :
2844 0x0000 1FFF
2845 0x0000 2000 Free for Application Use
2846 :
2847 :
2848
2849 :
2850 :
2851 0x00FB FF20 Monitor Stack (Growing downward)
2852 0x00FB FFAC Board Info Data and permanent copy of global data
2853 0x00FC 0000 Malloc Arena
2854 :
2855 0x00FD FFFF
2856 0x00FE 0000 RAM Copy of Monitor Code
2857 ... eventually: LCD or video framebuffer
2858 ... eventually: pRAM (Protected RAM - unchanged by reset)
2859 0x00FF FFFF [End of RAM]
2860
2861
2862System Initialization:
2863----------------------
2864
2865In the reset configuration, U-Boot starts at the reset entry point
2866(on most PowerPC systens at address 0x00000100). Because of the reset
2867configuration for CS0# this is a mirror of the onboard Flash memory.
2868To be able to re-map memory U-Boot then jumps to it's link address.
2869To be able to implement the initialization code in C, a (small!)
2870initial stack is set up in the internal Dual Ported RAM (in case CPUs
2871which provide such a feature like MPC8xx or MPC8260), or in a locked
2872part of the data cache. After that, U-Boot initializes the CPU core,
2873the caches and the SIU.
2874
2875Next, all (potentially) available memory banks are mapped using a
2876preliminary mapping. For example, we put them on 512 MB boundaries
2877(multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
2878on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
2879programmed for SDRAM access. Using the temporary configuration, a
2880simple memory test is run that determines the size of the SDRAM
2881banks.
2882
2883When there is more than one SDRAM bank, and the banks are of
2884different size, the larger is mapped first. For equal size, the first
2885bank (CS2#) is mapped first. The first mapping is always for address
28860x00000000, with any additional banks following immediately to create
2887contiguous memory starting from 0.
2888
2889Then, the monitor installs itself at the upper end of the SDRAM area
2890and allocates memory for use by malloc() and for the global Board
2891Info data; also, the exception vector code is copied to the low RAM
2892pages, and the final stack is set up.
2893
2894Only after this relocation will you have a "normal" C environment;
2895until that you are restricted in several ways, mostly because you are
2896running from ROM, and because the code will have to be relocated to a
2897new address in RAM.
2898
2899
2900U-Boot Porting Guide:
2901----------------------
2902
2903[Based on messages by Jerry Van Baren in the U-Boot-Users mailing
wdenk6aff3112002-12-17 01:51:00 +00002904list, October 2002]
wdenkc6097192002-11-03 00:24:07 +00002905
2906
2907int main (int argc, char *argv[])
2908{
2909 sighandler_t no_more_time;
2910
2911 signal (SIGALRM, no_more_time);
2912 alarm (PROJECT_DEADLINE - toSec (3 * WEEK));
2913
2914 if (available_money > available_manpower) {
2915 pay consultant to port U-Boot;
2916 return 0;
2917 }
2918
2919 Download latest U-Boot source;
2920
wdenk6aff3112002-12-17 01:51:00 +00002921 Subscribe to u-boot-users mailing list;
2922
wdenkc6097192002-11-03 00:24:07 +00002923 if (clueless) {
2924 email ("Hi, I am new to U-Boot, how do I get started?");
2925 }
2926
2927 while (learning) {
2928 Read the README file in the top level directory;
2929 Read http://www.denx.de/re/DPLG.html
2930 Read the source, Luke;
2931 }
2932
2933 if (available_money > toLocalCurrency ($2500)) {
2934 Buy a BDI2000;
2935 } else {
2936 Add a lot of aggravation and time;
2937 }
2938
2939 Create your own board support subdirectory;
2940
wdenk6aff3112002-12-17 01:51:00 +00002941 Create your own board config file;
2942
wdenkc6097192002-11-03 00:24:07 +00002943 while (!running) {
2944 do {
2945 Add / modify source code;
2946 } until (compiles);
2947 Debug;
2948 if (clueless)
2949 email ("Hi, I am having problems...");
2950 }
2951 Send patch file to Wolfgang;
2952
2953 return 0;
2954}
2955
2956void no_more_time (int sig)
2957{
2958 hire_a_guru();
2959}
2960
2961
2962
2963Coding Standards:
2964-----------------
2965
2966All contributions to U-Boot should conform to the Linux kernel
2967coding style; see the file "Documentation/CodingStyle" in your Linux
2968kernel source directory.
2969
2970Please note that U-Boot is implemented in C (and to some small parts
2971in Assembler); no C++ is used, so please do not use C++ style
2972comments (//) in your code.
2973
2974Submissions which do not conform to the standards may be returned
2975with a request to reformat the changes.
2976
2977
2978Submitting Patches:
2979-------------------
2980
2981Since the number of patches for U-Boot is growing, we need to
2982establish some rules. Submissions which do not conform to these rules
2983may be rejected, even when they contain important and valuable stuff.
2984
2985
2986When you send a patch, please include the following information with
2987it:
2988
2989* For bug fixes: a description of the bug and how your patch fixes
2990 this bug. Please try to include a way of demonstrating that the
2991 patch actually fixes something.
2992
2993* For new features: a description of the feature and your
2994 implementation.
2995
2996* A CHANGELOG entry as plaintext (separate from the patch)
2997
2998* For major contributions, your entry to the CREDITS file
2999
3000* When you add support for a new board, don't forget to add this
3001 board to the MAKEALL script, too.
3002
3003* If your patch adds new configuration options, don't forget to
3004 document these in the README file.
3005
3006* The patch itself. If you are accessing the CVS repository use "cvs
3007 update; cvs diff -puRN"; else, use "diff -purN OLD NEW". If your
3008 version of diff does not support these options, then get the latest
3009 version of GNU diff.
3010
3011 We accept patches as plain text, MIME attachments or as uuencoded
3012 gzipped text.
3013
wdenk52f52c12003-06-19 23:04:19 +00003014* If one logical set of modifications affects or creates several
3015 files, all these changes shall be submitted in a SINGLE patch file.
3016
3017* Changesets that contain different, unrelated modifications shall be
3018 submitted as SEPARATE patches, one patch per changeset.
3019
3020
wdenkc6097192002-11-03 00:24:07 +00003021Notes:
3022
3023* Before sending the patch, run the MAKEALL script on your patched
3024 source tree and make sure that no errors or warnings are reported
3025 for any of the boards.
3026
3027* Keep your modifications to the necessary minimum: A patch
3028 containing several unrelated changes or arbitrary reformats will be
3029 returned with a request to re-formatting / split it.
3030
3031* If you modify existing code, make sure that your new code does not
3032 add to the memory footprint of the code ;-) Small is beautiful!
3033 When adding new features, these should compile conditionally only
3034 (using #ifdef), and the resulting code with the new feature
3035 disabled must not need more memory than the old code without your
3036 modification.