Sync qca-vendor_copy.h with latest hostap
This bring qca-vendor.h definitions as on 2020-09-03.
CRs-Fixed: 2766035
Change-Id: Ica9a871bef2ab0b64c27df0cb85ae3ce66dddd98
diff --git a/qcwcn/wifi_hal/qca-vendor_copy.h b/qcwcn/wifi_hal/qca-vendor_copy.h
index 636feef..2e9a44d 100644
--- a/qcwcn/wifi_hal/qca-vendor_copy.h
+++ b/qcwcn/wifi_hal/qca-vendor_copy.h
@@ -1,7 +1,10 @@
/*
* Qualcomm Atheros OUI and vendor specific assignments
* Copyright (c) 2014-2017, Qualcomm Atheros, Inc.
- * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018-2020, The Linux Foundation
+ *
+ * This software may be distributed under the terms of the BSD license.
+ * See README for more details.
*/
#ifndef QCA_VENDOR_H
@@ -15,6 +18,7 @@
*/
#define OUI_QCA 0x001374
+
#ifndef BIT
#define BIT(x) (1U << (x))
#endif
@@ -170,6 +174,22 @@
* to notify the connected station's status. The attributes for this
* command are defined in enum qca_wlan_vendor_attr_link_properties.
*
+ * @QCA_NL80211_VENDOR_SUBCMD_SETBAND: Command to configure the enabled band(s)
+ * to the driver. This command sets the band(s) through either the
+ * attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE or
+ * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK (or both).
+ * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE refers enum qca_set_band as unsigned
+ * integer values and QCA_WLAN_VENDOR_ATTR_SETBAND_MASK refers it as 32
+ * bit unsigned bitmask values. The allowed values for
+ * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE are limited to QCA_SETBAND_AUTO,
+ * QCA_SETBAND_5G, and QCA_SETBAND_2G. Other values/bitmasks are valid for
+ * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. The attribute
+ * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE is deprecated and the recommendation
+ * is to use the QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. If the both attributes
+ * are included for backwards compatibility, the configurations through
+ * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK will take the precedence with drivers
+ * that support both attributes.
+ *
* @QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY: This command is used to configure
* DFS policy and channel hint for ACS operation. This command uses the
* attributes defined in enum qca_wlan_vendor_attr_acs_config and
@@ -625,6 +645,55 @@
* user space for the SAR power limits configuration from user space. If
* the driver does not get the SAR power limits from user space for all
* the retried attempts, it can configure a default SAR power limit.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO: This acts as a vendor event and
+ * is used to update the information about the station from the driver to
+ * userspace. Uses attributes from enum
+ * qca_wlan_vendor_attr_update_sta_info.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON: This acts as an event.
+ * The host driver initiates the disconnection for scenarios such as beacon
+ * miss, NUD failure, peer kick out, etc. The disconnection indication
+ * through cfg80211_disconnected() expects the reason codes from enum
+ * ieee80211_reasoncode which does not signify these various reasons why
+ * the driver has triggered the disconnection. This event will be used to
+ * send the driver specific reason codes by the host driver to userspace.
+ * Host drivers should trigger this event and pass the respective reason
+ * code immediately prior to triggering cfg80211_disconnected(). The
+ * attributes used with this event are defined in enum
+ * qca_wlan_vendor_attr_driver_disconnect_reason.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC: This vendor subcommand is used to
+ * add/delete TSPEC for each AC. One command is for one specific AC only.
+ * This command can only be used in STA mode and the STA must be
+ * associated with an AP when the command is issued. Uses attributes
+ * defined in enum qca_wlan_vendor_attr_config_tspec.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT: Vendor subcommand to configure TWT.
+ * Uses attributes defined in enum qca_wlan_vendor_attr_config_twt.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GETBAND: Command to get the enabled band(s) from
+ * the driver. The band configurations obtained are referred through
+ * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS: Vendor subcommand/event for medium
+ * assessment.
+ * Uses attributes defined in enum qca_wlan_vendor_attr_medium_assess.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID: This acts as a vendor event and is
+ * used to update SSID information in hostapd when it is updated in the
+ * driver. Uses the attribute NL80211_ATTR_SSID.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_WIFI_FW_STATS: This vendor subcommand is used by
+ * the driver to send opaque data from the firmware to userspace. The
+ * driver sends an event to userspace whenever such data is received from
+ * the firmware.
+ *
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA is used as the attribute to
+ * send this opaque data for this event.
+ *
+ * The format of the opaque data is specific to the particular firmware
+ * version and there is no guarantee of the format remaining same.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
@@ -802,6 +871,14 @@
QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE = 185,
QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO = 186,
QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS_EVENT = 187,
+ QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO = 188,
+ QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON = 189,
+ QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC = 190,
+ QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT = 191,
+ QCA_NL80211_VENDOR_SUBCMD_GETBAND = 192,
+ QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS = 193,
+ QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID = 194,
+ QCA_NL80211_VENDOR_SUBCMD_WIFI_FW_STATS = 195,
};
enum qca_wlan_vendor_attr {
@@ -832,7 +909,11 @@
QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10,
/* Unsigned 32-bit value */
QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11,
- /* Unsigned 32-bit value from enum qca_set_band. */
+ /* Unsigned 32-bit value from enum qca_set_band. The allowed values for
+ * this attribute are limited to QCA_SETBAND_AUTO, QCA_SETBAND_5G, and
+ * QCA_SETBAND_2G. This attribute is deprecated. Recommendation is to
+ * use QCA_WLAN_VENDOR_ATTR_SETBAND_MASK instead.
+ */
QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12,
/* Dummy (NOP) attribute for 64 bit padding */
QCA_WLAN_VENDOR_ATTR_PAD = 13,
@@ -995,6 +1076,15 @@
*/
QCA_WLAN_VENDOR_ATTR_FW_STATE = 42,
+ /* Unsigned 32-bitmask value from enum qca_set_band. Substitutes the
+ * attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE for which only a subset
+ * of single values from enum qca_set_band are valid. This attribute
+ * uses bitmask combinations to define the respective allowed band
+ * combinations and this attributes takes precedence over
+ * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE if both attributes are included.
+ */
+ QCA_WLAN_VENDOR_ATTR_SETBAND_MASK = 43,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1,
@@ -1256,6 +1346,15 @@
* Note: If the driver supports the 6 GHz band, the event sent from the driver
* includes this attribute along with
* QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED: Flag attribute.
+ * Used with command to notify the driver of EDMG request for ACS
+ * operation.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL: Optional (u8).
+ * Used with event to notify the EDMG channel number selected in ACS
+ * operation.
+ * EDMG primary channel is indicated by QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL
*/
enum qca_wlan_vendor_attr_acs_offload {
QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0,
@@ -1274,6 +1373,8 @@
QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY = 13,
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY = 14,
QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY = 15,
+ QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED = 16,
+ QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL = 17,
/* keep last */
QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST,
@@ -1531,9 +1632,10 @@
};
enum qca_set_band {
- QCA_SETBAND_AUTO,
- QCA_SETBAND_5G,
- QCA_SETBAND_2G,
+ QCA_SETBAND_AUTO = 0,
+ QCA_SETBAND_5G = BIT(0),
+ QCA_SETBAND_2G = BIT(1),
+ QCA_SETBAND_6G = BIT(2),
};
/**
@@ -1661,6 +1763,8 @@
* (not including the Element ID Extension field). Please note that the
* draft is still work in progress and this element payload is subject to
* change.
+ *
+ * @QCA_VENDOR_ELEM_ALLPLAY: Allplay element
*/
enum qca_vendor_element_id {
QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0,
@@ -1669,6 +1773,7 @@
QCA_VENDOR_ELEM_RAPS = 3,
QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4,
QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5,
+ QCA_VENDOR_ELEM_ALLPLAY = 6,
};
/**
@@ -1693,6 +1798,9 @@
* randomisation
* @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the
* specific BSSID to scan for.
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME: Unsigned 64-bit dwell time in
+ * microseconds. This is a common value which applies across all
+ * frequencies specified by QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES.
*/
enum qca_wlan_vendor_attr_scan {
QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0,
@@ -1707,6 +1815,7 @@
QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9,
QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10,
QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11,
+ QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME = 12,
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SCAN_MAX =
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1
@@ -2061,19 +2170,186 @@
* take the union of IEs from both of these interfaces and send in
* further disassoc/deauth frames.
*/
- QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES = 58,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES = 58,
/* 8-bit unsigned value for ELNA bypass.
* 1-Enable, 0-Disable
*/
QCA_WLAN_VENDOR_ATTR_CONFIG_ELNA_BYPASS = 59,
+ /* 8-bit unsigned value. This attribute enables/disables the host driver
+ * to send the Beacon Report Response with failure reason for the
+ * scenarios where STA cannot honor the Beacon Report Request from AP.
+ * 1-Enable, 0-Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL = 60,
+
+ /* 8-bit unsigned value. This attribute enables/disables the host driver
+ * to send roam reason information in the Reassociation Request frame to
+ * the target AP when roaming within the same ESS.
+ * 1-Enable, 0-Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON = 61,
+
+ /* 32-bit unsigned value to configure different PHY modes to the
+ * driver/firmware. The possible values are defined in
+ * enum qca_wlan_vendor_phy_mode. The configuration will be reset to
+ * default value, i.e., QCA_WLAN_VENDOR_PHY_MODE_AUTO upon restarting
+ * the driver.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PHY_MODE = 62,
+
+ /* 8-bit unsigned value to configure the maximum supported channel width
+ * for STA mode. If this value is configured when STA is in connected
+ * state, it should not exceed the negotiated channel width. If it is
+ * configured when STA is in disconnected state, the configured value
+ * will take effect for the next immediate connection.
+ * Possible values are:
+ * NL80211_CHAN_WIDTH_20
+ * NL80211_CHAN_WIDTH_40
+ * NL80211_CHAN_WIDTH_80
+ * NL80211_CHAN_WIDTH_80P80
+ * NL80211_CHAN_WIDTH_160
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH = 63,
+
+ /* 8-bit unsigned value to enable/disable dynamic bandwidth adjustment.
+ * This attribute is only applicable for STA mode. When dynamic
+ * bandwidth adjustment is disabled, STA will use static channel width
+ * the value of which is negotiated during connection.
+ * 1-enable (default), 0-disable
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_BW = 64,
+
+ /* 8-bit unsigned value to configure the maximum number of subframes of
+ * TX MSDU for aggregation. Possible values are 0-31. When set to 0,
+ * it is decided by the hardware.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MSDU_AGGREGATION = 65,
+
+ /* 8-bit unsigned value to configure the maximum number of subframes of
+ * RX MSDU for aggregation. Possible values are 0-31. When set to 0,
+ * it is decided by the hardware.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MSDU_AGGREGATION = 66,
+
+ /* 8-bit unsigned value. This attribute is used to dynamically
+ * enable/disable the LDPC capability of the device. When configured in
+ * the disconnected state, the updated configuration will be considered
+ * for the immediately following connection attempt. If this
+ * configuration is modified while the device is in the connected state,
+ * the LDPC TX will be updated with this configuration immediately,
+ * while the LDPC RX configuration update will take place starting from
+ * the subsequent association attempt.
+ * 1-Enable, 0-Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_LDPC = 67,
+
+ /* 8-bit unsigned value. This attribute is used to dynamically
+ * enable/disable the TX STBC capability of the device. When configured
+ * in the disconnected state, the updated configuration will be
+ * considered for the immediately following connection attempt. If the
+ * connection is formed with TX STBC enabled and if this configuration
+ * is disabled during that association, the TX will be impacted
+ * immediately. Further connection attempts will disable TX STBC.
+ * However, enabling the TX STBC for a connected session with disabled
+ * capability is not allowed and will fail.
+ * 1-Enable, 0-Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_STBC = 68,
+
+ /* 8-bit unsigned value. This attribute is used to dynamically
+ * enable/disable the RX STBC capability of the device. When configured
+ * in the disconnected state, the updated configuration will be
+ * considered for the immediately following connection attempt. If the
+ * configuration is modified in the connected state, there will be no
+ * impact for the current association, but further connection attempts
+ * will use the updated configuration.
+ * 1-Enable, 0-Disable.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_STBC = 69,
+
+ /* 8-bit unsigned value. This attribute is used to dynamically configure
+ * the number of spatial streams. When configured in the disconnected
+ * state, the updated configuration will be considered for the
+ * immediately following connection attempt. If the NSS is updated after
+ * the connection, the updated NSS value is notified to the peer using
+ * the Operating Mode Notification/Spatial Multiplexing Power Save
+ * frame. The updated NSS value after the connection shall not be
+ * greater than the one negotiated during the connection. Any such
+ * higher value configuration shall be returned with a failure.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_NSS = 70,
+ /* 8-bit unsigned value to trigger Optimized Power Management:
+ * 1-Enable, 0-Disable
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT = 71,
+
+ /* 8-bit unsigned value. This attribute takes the QoS/access category
+ * value represented by the enum qca_wlan_ac_type and expects the driver
+ * to upgrade the UDP frames to this access category. The value of
+ * QCA_WLAN_AC_ALL is invalid for this attribute. This will override the
+ * DSCP value configured in the frame with the intention to only upgrade
+ * the access category. That said, it is not intended to downgrade the
+ * access category for the frames.
+ * Set the value to QCA_WLAN_AC_BK if the QoS upgrade needs to be
+ * disabled, as BK is of the lowest priority and an upgrade to it does
+ * not result in any changes for the frames.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE = 72,
+
+ /* 8-bit unsigned value. This attribute is used to dynamically configure
+ * the number of chains to be used for transmitting data. This
+ * configuration is allowed only when in connected state and will be
+ * effective until disconnected. The driver rejects this configuration
+ * if the number of spatial streams being used in the current connection
+ * cannot be supported by this configuration.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_NUM_TX_CHAINS = 73,
+ /* 8-bit unsigned value. This attribute is used to dynamically configure
+ * the number of chains to be used for receiving data. This
+ * configuration is allowed only when in connected state and will be
+ * effective until disconnected. The driver rejects this configuration
+ * if the number of spatial streams being used in the current connection
+ * cannot be supported by this configuration.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_NUM_RX_CHAINS = 74,
+
+ /* 8-bit unsigned value to configure ANI setting type.
+ * See &enum qca_wlan_ani_setting for possible values.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANI_SETTING = 75,
+ /* 32-bit signed value to configure ANI level. This is used when
+ * ANI settings type is &QCA_WLAN_ANI_SETTING_FIXED.
+ * The set and get of ANI level with &QCA_WLAN_ANI_SETTING_AUTO
+ * is invalid, the driver will return a failure.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ANI_LEVEL = 76,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_CONFIG_MAX =
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1,
};
+/* Compatibility defines for previously used incorrect enum
+ * qca_wlan_vendor_attr_config names. These values should not be used in any
+ * new implementation. */
+#define QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES \
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES
+#define QCA_WLAN_VENDOR_ATTR_BEACON_REPORT_FAIL \
+ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL
+
+/**
+ * enum qca_wlan_ani_setting - ANI setting type
+ * @QCA_WLAN_ANI_SETTING_AUTO: Automatically determine ANI level
+ * @QCA_WLAN_ANI_SETTING_FIXED: Fix ANI level to the dBm parameter
+ */
+enum qca_wlan_ani_setting {
+ QCA_WLAN_ANI_SETTING_AUTO = 0,
+ QCA_WLAN_ANI_SETTING_FIXED = 1,
+};
+
/**
* enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
*
@@ -2129,19 +2405,54 @@
/**
* enum qca_wlan_gpio_attr - Parameters for GPIO configuration
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND: Required (u32)
+ * value to specify the GPIO command. Please refer to enum qca_gpio_cmd_type
+ * for the available values.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM: Required (u32)
+ * value to specify the GPIO number.
+ * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG or %QCA_WLAN_VENDOR_GPIO_OUTPUT.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE: Required (u32)
+ * value to specify the GPIO output level. Please refer to enum qca_gpio_value
+ * for the available values.
+ * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
+ * %QCA_WLAN_VENDOR_GPIO_OUTPUT.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE: Required (u32)
+ * value to specify the GPIO pull type. Please refer to enum qca_gpio_pull_type
+ * for the available values.
+ * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE: Required (u32)
+ * value to specify the GPIO interrupt mode. Please refer to enum
+ * qca_gpio_interrupt_mode for the available values.
+ * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR: Required (u32)
+ * value to specify the GPIO direction. Please refer to enum qca_gpio_direction
+ * for the available values.
+ * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is
+ * %QCA_WLAN_VENDOR_GPIO_CONFIG.
*/
enum qca_wlan_gpio_attr {
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
/* Unsigned 32-bit attribute for GPIO command */
- QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND = 1,
/* Unsigned 32-bit attribute for GPIO PIN number to configure */
- QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM = 2,
/* Unsigned 32-bit attribute for GPIO value to configure */
- QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE = 3,
/* Unsigned 32-bit attribute for GPIO pull type */
- QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE = 4,
/* Unsigned 32-bit attribute for GPIO interrupt mode */
- QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE = 5,
+ /* Unsigned 32-bit attribute for GPIO direction to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR = 6,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
@@ -2150,6 +2461,73 @@
};
/**
+ * enum gpio_cmd_type - GPIO configuration command type
+ * @QCA_WLAN_VENDOR_GPIO_CONFIG: Set GPIO configuration info
+ * @QCA_WLAN_VENDOR_GPIO_OUTPUT: Set GPIO output level
+ */
+enum qca_gpio_cmd_type {
+ QCA_WLAN_VENDOR_GPIO_CONFIG = 0,
+ QCA_WLAN_VENDOR_GPIO_OUTPUT = 1,
+};
+
+/**
+ * enum qca_gpio_pull_type - GPIO pull type
+ * @QCA_WLAN_GPIO_PULL_NONE: Set GPIO pull type to none
+ * @QCA_WLAN_GPIO_PULL_UP: Set GPIO pull up
+ * @QCA_WLAN_GPIO_PULL_DOWN: Set GPIO pull down
+ */
+enum qca_gpio_pull_type {
+ QCA_WLAN_GPIO_PULL_NONE = 0,
+ QCA_WLAN_GPIO_PULL_UP = 1,
+ QCA_WLAN_GPIO_PULL_DOWN = 2,
+ QCA_WLAN_GPIO_PULL_MAX,
+};
+
+/**
+ * enum qca_gpio_direction - GPIO direction
+ * @QCA_WLAN_GPIO_INPUT: Set GPIO as input mode
+ * @QCA_WLAN_GPIO_OUTPUT: Set GPIO as output mode
+ * @QCA_WLAN_GPIO_VALUE_MAX: Invalid value
+ */
+enum qca_gpio_direction {
+ QCA_WLAN_GPIO_INPUT = 0,
+ QCA_WLAN_GPIO_OUTPUT = 1,
+ QCA_WLAN_GPIO_DIR_MAX,
+};
+
+/**
+ * enum qca_gpio_value - GPIO Value
+ * @QCA_WLAN_GPIO_LEVEL_LOW: set gpio output level to low
+ * @QCA_WLAN_GPIO_LEVEL_HIGH: set gpio output level to high
+ * @QCA_WLAN_GPIO_LEVEL_MAX: Invalid value
+ */
+enum qca_gpio_value {
+ QCA_WLAN_GPIO_LEVEL_LOW = 0,
+ QCA_WLAN_GPIO_LEVEL_HIGH = 1,
+ QCA_WLAN_GPIO_LEVEL_MAX,
+};
+
+/**
+ * enum gpio_interrupt_mode - GPIO interrupt mode
+ * @QCA_WLAN_GPIO_INTMODE_DISABLE: Disable interrupt trigger
+ * @QCA_WLAN_GPIO_INTMODE_RISING_EDGE: Interrupt with GPIO rising edge trigger
+ * @QCA_WLAN_GPIO_INTMODE_FALLING_EDGE: Interrupt with GPIO falling edge trigger
+ * @QCA_WLAN_GPIO_INTMODE_BOTH_EDGE: Interrupt with GPIO both edge trigger
+ * @QCA_WLAN_GPIO_INTMODE_LEVEL_LOW: Interrupt with GPIO level low trigger
+ * @QCA_WLAN_GPIO_INTMODE_LEVEL_HIGH: Interrupt with GPIO level high trigger
+ * @QCA_WLAN_GPIO_INTMODE_MAX: Invalid value
+ */
+enum qca_gpio_interrupt_mode {
+ QCA_WLAN_GPIO_INTMODE_DISABLE = 0,
+ QCA_WLAN_GPIO_INTMODE_RISING_EDGE = 1,
+ QCA_WLAN_GPIO_INTMODE_FALLING_EDGE = 2,
+ QCA_WLAN_GPIO_INTMODE_BOTH_EDGE = 3,
+ QCA_WLAN_GPIO_INTMODE_LEVEL_LOW = 4,
+ QCA_WLAN_GPIO_INTMODE_LEVEL_HIGH = 5,
+ QCA_WLAN_GPIO_INTMODE_MAX,
+};
+
+/**
* qca_wlan_set_qdepth_thresh_attr - Parameters for setting
* MSDUQ depth threshold per peer per tid in the target
*
@@ -3237,7 +3615,7 @@
QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66,
/* Signifies the nested list of channel attributes
- * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_*
+ * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_*
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67,
@@ -3299,6 +3677,17 @@
*/
QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83,
+ /* u32 value representing total time in milliseconds for which the radio
+ * is transmitting on this channel. This attribute will be nested
+ * within QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_TX_TIME = 84,
+ /* u32 value representing total time in milliseconds for which the radio
+ * is receiving all 802.11 frames intended for this device on this
+ * channel. This attribute will be nested within
+ * QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO.
+ */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_RX_TIME = 85,
/* keep last */
QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX =
@@ -3866,7 +4255,7 @@
* Represents the Request ID for the specific set of commands.
* This also helps to map specific set of commands to the respective
* ID / client. e.g., helps to identify the user entity configuring the
- * Blacklist BSSID and accordingly clear the respective ones with the
+ * ignored BSSIDs and accordingly clear the respective ones with the
* matching ID.
*
* @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS: Unsigned
@@ -3933,17 +4322,18 @@
* the BSSID for the purpose of comparing it with other roam candidate.
*
* @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS: Nested attribute,
- * represents the BSSIDs to get blacklisted for roaming.
+ * represents the BSSIDs to get ignored for roaming.
*
* @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID: Unsigned
- * 32-bit value, represents the number of blacklisted BSSIDs.
+ * 32-bit value, represents the number of ignored BSSIDs.
*
* @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID: 6-byte MAC
- * address representing the Blacklisted BSSID.
+ * address representing the ignored BSSID.
*
* @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT: Flag attribute,
- * indicates this BSSID blacklist as a hint to the driver. The driver can
- * select this BSSID in the worst case (when no other BSSIDs are better).
+ * indicates this request to ignore the BSSID as a hint to the driver. The
+ * driver can select this BSSID in the worst case (when no other BSSIDs are
+ * better).
*
* @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL: Nested attribute to
* set/get/clear the roam control config as
@@ -3978,11 +4368,11 @@
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17,
- /* Attribute for set_blacklist bssid params */
+ /* Attribute for setting ignored BSSID parameters */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20,
- /* Flag attribute indicates this BSSID blacklist as a hint */
+ /* Flag attribute indicates this entry as a hint */
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT = 21,
QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL = 22,
@@ -4018,9 +4408,9 @@
* QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS to set the BSSID
* preference.
*
- * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID: Sets the Blacklist
- * BSSIDs. Refers QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS to
- * set the same.
+ * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID: Sets the list of BSSIDs
+ * to ignore in roaming decision. Uses
+ * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS to set the list.
*
* @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET: Command to set the
* roam control config to the driver with the attribute
@@ -4682,9 +5072,9 @@
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6,
/* Station only channel */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7,
- /* DFS radar history for slave device (STA mode) */
+ /* DFS radar history for client device (STA mode) */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8,
- /* DFS CAC valid for slave device (STA mode) */
+ /* DFS CAC valid for client device (STA mode) */
QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9,
};
@@ -5407,8 +5797,12 @@
* QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE
* Center frequency (in MHz) of the span of interest or
* for convenience, center frequency (in MHz) of any channel
- * in the span of interest. If agile spectral scan is initiated
- * without setting a valid frequency it returns the error code
+ * in the span of interest. For 80+80 MHz agile spectral scan
+ * request it represents center frequency (in MHz) of the primary
+ * 80 MHz span or for convenience, center frequency (in MHz) of any
+ * channel in the primary 80 MHz span. If agile spectral scan is
+ * initiated without setting a valid frequency it returns the
+ * error code
* (QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED).
* u32 attribute.
*/
@@ -5435,6 +5829,20 @@
* 1-enable, 0-disable
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG = 28,
+ /* This specifies the frequency span over which spectral scan would be
+ * carried out. Its value depends on the value of
+ * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE and the relation is as
+ * follows.
+ * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL
+ * Not applicable. Spectral scan would happen in the operating span.
+ * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE
+ * This attribute is applicable only for agile spectral scan
+ * requests in 80+80 MHz mode. It represents center frequency (in
+ * MHz) of the secondary 80 MHz span or for convenience, center
+ * frequency (in MHz) of any channel in the secondary 80 MHz span.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY_2 = 29,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX =
@@ -5525,6 +5933,26 @@
* for 80+80 MHz mode.
*/
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_80_80 = 13,
+ /* Number of spectral detectors used for scan in 20 MHz.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_20_MHZ = 14,
+ /* Number of spectral detectors used for scan in 40 MHz.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_40_MHZ = 15,
+ /* Number of spectral detectors used for scan in 80 MHz.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_80_MHZ = 16,
+ /* Number of spectral detectors used for scan in 160 MHz.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_160_MHZ = 17,
+ /* Number of spectral detectors used for scan in 80+80 MHz.
+ * u32 attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_80P80_MHZ = 18,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX =
@@ -5674,6 +6102,39 @@
QCA_WLAN_HANG_DXE_FAILURE = 12,
/* WMI pending commands exceed the maximum count */
QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13,
+ /* Timeout for peer STA connection accept command's response from the
+ * FW in AP mode. This command is triggered when a STA (peer) connects
+ * to AP (DUT).
+ */
+ QCA_WLAN_HANG_AP_STA_CONNECT_REQ_TIMEOUT = 14,
+ /* Timeout for the AP connection accept command's response from the FW
+ * in STA mode. This command is triggered when the STA (DUT) connects
+ * to an AP (peer).
+ */
+ QCA_WLAN_HANG_STA_AP_CONNECT_REQ_TIMEOUT = 15,
+ /* Timeout waiting for the response to the MAC HW mode change command
+ * sent to FW as a part of MAC mode switch among DBS (Dual Band
+ * Simultaneous), SCC (Single Channel Concurrency), and MCC (Multi
+ * Channel Concurrency) mode.
+ */
+ QCA_WLAN_HANG_MAC_HW_MODE_CHANGE_TIMEOUT = 16,
+ /* Timeout waiting for the response from FW to configure the MAC HW's
+ * mode. This operation is to configure the single/two MACs in either
+ * SCC/MCC/DBS mode.
+ */
+ QCA_WLAN_HANG_MAC_HW_MODE_CONFIG_TIMEOUT = 17,
+ /* Timeout waiting for response of VDEV start command from the FW */
+ QCA_WLAN_HANG_VDEV_START_RESPONSE_TIMED_OUT = 18,
+ /* Timeout waiting for response of VDEV restart command from the FW */
+ QCA_WLAN_HANG_VDEV_RESTART_RESPONSE_TIMED_OUT = 19,
+ /* Timeout waiting for response of VDEV stop command from the FW */
+ QCA_WLAN_HANG_VDEV_STOP_RESPONSE_TIMED_OUT = 20,
+ /* Timeout waiting for response of VDEV delete command from the FW */
+ QCA_WLAN_HANG_VDEV_DELETE_RESPONSE_TIMED_OUT = 21,
+ /* Timeout waiting for response of peer all delete request command to
+ * the FW on a specific VDEV.
+ */
+ QCA_WLAN_HANG_VDEV_PEER_DELETE_ALL_RESPONSE_TIMED_OUT = 22,
};
/**
@@ -5686,6 +6147,12 @@
* qca_wlan_vendor_hang_reason.
*/
QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1,
+ /* The binary blob data associated with the hang reason specified by
+ * QCA_WLAN_VENDOR_ATTR_HANG_REASON. This binary data is expected to
+ * contain the required dump to analyze the reason for the hang.
+ * NLA_BINARY attribute, the max size is 1024 bytes.
+ */
+ QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA = 2,
QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_HANG_MAX =
@@ -6710,6 +7177,72 @@
QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST - 1,
};
+ /**
+ * enum qca_wlan_vendor_phy_mode - Different PHY modes
+ * These values are used with %QCA_WLAN_VENDOR_ATTR_CONFIG_PHY_MODE.
+ *
+ * @QCA_WLAN_VENDOR_PHY_MODE_AUTO: autoselect
+ * @QCA_WLAN_VENDOR_PHY_MODE_2G_AUTO: 2.4 GHz 802.11b/g/n/ax autoselect
+ * @QCA_WLAN_VENDOR_PHY_MODE_5G_AUTO: 5 GHz 802.11a/n/ac/ax autoselect
+ * @QCA_WLAN_VENDOR_PHY_MODE_11A: 5 GHz, OFDM
+ * @QCA_WLAN_VENDOR_PHY_MODE_11B: 2.4 GHz, CCK
+ * @QCA_WLAN_VENDOR_PHY_MODE_11G: 2.4 GHz, OFDM
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AGN: Support 802.11n in both 2.4 GHz and 5 GHz
+ * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT20: 2.4 GHz, HT20
+ * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40PLUS: 2.4 GHz, HT40 (ext ch +1)
+ * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40MINUS: 2.4 GHz, HT40 (ext ch -1)
+ * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40: 2.4 GHz, Auto HT40
+ * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT20: 5 GHz, HT20
+ * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40PLUS: 5 GHz, HT40 (ext ch +1)
+ * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40MINUS: 5 GHz, HT40 (ext ch -1)
+ * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40: 5 GHz, Auto HT40
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT20: 5 GHz, VHT20
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40PLUS: 5 GHz, VHT40 (Ext ch +1)
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40MINUS: 5 GHz VHT40 (Ext ch -1)
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40: 5 GHz, VHT40
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80: 5 GHz, VHT80
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80P80: 5 GHz, VHT80+80
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT160: 5 GHz, VHT160
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE20: HE20
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40: HE40
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40PLUS: HE40 (ext ch +1)
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40MINUS: HE40 (ext ch -1)
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80: HE80
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80P80: HE 80P80
+ * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE160: HE160
+ */
+enum qca_wlan_vendor_phy_mode {
+ QCA_WLAN_VENDOR_PHY_MODE_AUTO = 0,
+ QCA_WLAN_VENDOR_PHY_MODE_2G_AUTO = 1,
+ QCA_WLAN_VENDOR_PHY_MODE_5G_AUTO = 2,
+ QCA_WLAN_VENDOR_PHY_MODE_11A = 3,
+ QCA_WLAN_VENDOR_PHY_MODE_11B = 4,
+ QCA_WLAN_VENDOR_PHY_MODE_11G = 5,
+ QCA_WLAN_VENDOR_PHY_MODE_11AGN = 6,
+ QCA_WLAN_VENDOR_PHY_MODE_11NG_HT20 = 7,
+ QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40PLUS = 8,
+ QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40MINUS = 9,
+ QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40 = 10,
+ QCA_WLAN_VENDOR_PHY_MODE_11NA_HT20 = 11,
+ QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40PLUS = 12,
+ QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40MINUS = 13,
+ QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40 = 14,
+ QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT20 = 15,
+ QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40PLUS = 16,
+ QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40MINUS = 17,
+ QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40 = 18,
+ QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80 = 19,
+ QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80P80 = 20,
+ QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT160 = 21,
+ QCA_WLAN_VENDOR_PHY_MODE_11AX_HE20 = 22,
+ QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40 = 23,
+ QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40PLUS = 24,
+ QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40MINUS = 25,
+ QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80 = 26,
+ QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80P80 = 27,
+ QCA_WLAN_VENDOR_PHY_MODE_11AX_HE160 = 28,
+};
+
/* Attributes for data used by
* QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION
*/
@@ -6993,6 +7526,57 @@
*/
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TWT_REQ_SUPPORT = 37,
+ /* 8-bit unsigned value to configure protection for Management
+ * frames when PMF is enabled for the association.
+ * This attribute is used to configure the testbed device.
+ * 0-use the correct key, 1-use an incorrect key, 2-disable protection.
+ */
+ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_PMF_PROTECTION = 38,
+
+ /* Flag attribute to inject Disassociation frame to the connected AP.
+ * This attribute is used to configure the testbed device.
+ */
+ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_DISASSOC_TX = 39,
+
+ /* 8-bit unsigned value to configure an override for the RSNXE Used
+ * subfield in the MIC control field of the FTE in FT Reassociation
+ * Request frame.
+ * 0 - Default behavior, 1 - override with 1, 2 - override with 0.
+ * This attribute is used to configure the testbed device.
+ * This attribute can be configured only when STA is in associated state
+ * and the configuration is valid until the disconnection.
+ */
+ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FT_REASSOCREQ_RSNXE_USED = 40,
+
+ /* 8-bit unsigned value to configure the driver to ignore CSA (Channel
+ * Switch Announcement) when STA is in connected state.
+ * 0 - Default behavior, 1 - Ignore CSA.
+ * This attribute is used to configure the testbed device.
+ * This attribute can be configured only when STA is in associated state
+ * and the configuration is valid until the disconnection.
+ */
+ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_CSA = 41,
+
+ /* Nested attribute values required to configure OCI (Operating Channel
+ * Information). Attributes defined in enum
+ * qca_wlan_vendor_attr_oci_override are nested within this attribute.
+ * This attribute is used to configure the testbed device.
+ * This attribute can be configured only when STA is in associated state
+ * and the configuration is valid until the disconnection.
+ */
+ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OCI_OVERRIDE = 42,
+
+ /* 8-bit unsigned value to configure the driver/firmware to ignore SA
+ * Query timeout. If this configuration is enabled STA shall not send
+ * Deauthentication frmae when SA Query times out (mainly, after a
+ * channel switch when OCV is enabled).
+ * 0 - Default behavior, 1 - Ignore SA Query timeout.
+ * This attribute is used to configure the testbed device.
+ * This attribute can be configured only when STA is in associated state
+ * and the configuration is valid until the disconnection.
+ */
+ QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_SA_QUERY_TIMEOUT = 43,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX =
@@ -7000,6 +7584,63 @@
};
/**
+ * enum qca_wlan_twt_operation - Operation of the config TWT request
+ * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION.
+ *
+ * @QCA_WLAN_TWT_SET: Setup a TWT session. Required parameters are configured
+ * through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum
+ * qca_wlan_vendor_attr_twt_setup.
+ *
+ * @QCA_WLAN_TWT_GET: Get the configured TWT parameters. Required parameters are
+ * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum
+ * qca_wlan_vendor_attr_twt_setup.
+ *
+ * @QCA_WLAN_TWT_TERMINATE: Terminate the TWT session. Required parameters are
+ * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum
+ * qca_wlan_vendor_attr_twt_setup. Valid only after the TWT session is setup.
+ *
+ * @QCA_WLAN_TWT_SUSPEND: Suspend the TWT session. Required parameters are
+ * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum
+ * qca_wlan_vendor_attr_twt_setup. Valid only after the TWT session is setup.
+ *
+ * @QCA_WLAN_TWT_RESUME: Resume the TWT session. Required parameters are
+ * configured through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum
+ * qca_wlan_vendor_attr_twt_resume. Valid only after the TWT session is setup.
+ */
+enum qca_wlan_twt_operation {
+ QCA_WLAN_TWT_SET = 0,
+ QCA_WLAN_TWT_GET = 1,
+ QCA_WLAN_TWT_TERMINATE = 2,
+ QCA_WLAN_TWT_SUSPEND = 3,
+ QCA_WLAN_TWT_RESUME = 4,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_config_twt: Defines attributes used by
+ * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION: u8 attribute. Specify the TWT
+ * operation of this request. Possible values are defined in enum
+ * qca_wlan_twt_operation. The parameters for the respective operation is
+ * specified through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS: Nested attribute representing the
+ * parameters configured for TWT. These parameters are represented by
+ * enum qca_wlan_vendor_attr_twt_setup or enum qca_wlan_vendor_attr_twt_resume
+ * based on the operation.
+ */
+enum qca_wlan_vendor_attr_config_twt {
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION = 1,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_MAX =
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_AFTER_LAST - 1,
+};
+
+/**
* enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command
* QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER.
* The user can add/delete the filter by specifying the BSSID/STA MAC address in
@@ -7150,7 +7791,8 @@
* enum qca_wlan_vendor_attr_twt_setup: Represents attributes for
* TWT (Target Wake Time) setup request. These attributes are sent as part of
* %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and
- * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
+ * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Also used by
+ * attributes through %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute.
* Disable (flag attribute not present) - Individual TWT
@@ -7160,10 +7802,13 @@
* STA and AP.
* Broadcast means the session is across multiple STAs and an AP. The
* configuration parameters are announced in Beacon frames by the AP.
+ * This is used in
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Response
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8).
* Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to
- * specify the TWT request type
+ * specify the TWT request type. This is used in TWT SET operation.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute
* Enable (flag attribute present) - TWT with trigger support.
@@ -7171,40 +7816,113 @@
* Trigger means the AP will send the trigger frame to allow STA to send data.
* Without trigger, the STA will wait for the MU EDCA timer before
* transmitting the data.
+ * This is used in
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Response
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8)
* 0 - Announced TWT - In this mode, STA may skip few service periods to
* save more power. If STA wants to wake up, it will send a PS-POLL/QoS
* NULL frame to AP.
* 1 - Unannounced TWT - The STA will wakeup during every SP.
+ * This is a required parameter for
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Response
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8)
* Flow ID is the unique identifier for each TWT session.
- * Currently this is not required and dialog ID will be set to zero.
+ * If not provided then dialog ID will be set to zero.
+ * This is an optional parameter for
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Request and Response
+ * 3. TWT TERMINATE Request and Response
+ * 4. TWT SUSPEND Request and Response
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8)
* This attribute (exp) is used along with the mantissa to derive the
* wake interval using the following formula:
* pow(2,exp) = wake_intvl_us/wake_intvl_mantis
* Wake interval is the interval between 2 successive SP.
+ * This is a required parameter for
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Response
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute
* Enable (flag attribute present) - Protection required.
* Disable (flag attribute not present) - Protection not required.
* If protection is enabled, then the AP will use protection
* mechanism using RTS/CTS to self to reserve the airtime.
+ * This is used in
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Response
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32)
* This attribute is used as the SP offset which is the offset from
* TSF after which the wake happens. The units are in microseconds. If
* this attribute is not provided, then the value will be set to zero.
+ * This is an optional parameter for
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Response
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32)
- * This is the duration of the service period. The units are in TU.
+ * This is the duration of the service period. This is specified as
+ * multiples of 256 microseconds. Valid values are 0x1 to 0xFF.
+ * This is a required parameter for
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Response
*
* @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32)
* This attribute is used to configure wake interval mantissa.
* The units are in TU.
+ * This is a required parameter for
+ * 1. TWT SET Request and Response
+ * 2. TWT GET Response
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATUS: Required (u8)
+ * This field is applicable for TWT response only.
+ * This contains status values in enum qca_wlan_vendor_twt_status
+ * and is passed to the userspace. This is used in TWT SET operation.
+ * This is a required parameter for
+ * 1. TWT SET Response
+ * 2. TWT TERMINATE Response
+ * 3. TWT SUSPEND Response
+ * 4. TWT RESUME Response
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESP_TYPE: Required (u8)
+ * This field is applicable for TWT response only.
+ * This field contains response type from the TWT responder and is
+ * passed to the userspace. The values for this field are defined in
+ * enum qca_wlan_vendor_twt_setup_resp_type. This is used in TWT SET
+ * response.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF: Required (u64)
+ * This field is applicable for TWT response only.
+ * This field contains absolute TSF value of the wake time received
+ * from the TWT responder and is passed to the userspace.
+ * This is a required parameter for
+ * 1. TWT SET Response
+ * 2. TWT GET Response
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TWT_INFO_ENABLED: Flag attribute.
+ * Enable (flag attribute present) - Indicates that the TWT responder
+ * supports reception of TWT information frame from the TWT requestor.
+ * Disable (flag attribute not present) - Indicates that the responder
+ * doesn't support reception of TWT information frame from requestor.
+ * This is used in
+ * 1. TWT SET Response
+ * 2. TWT GET Response
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAC_ADDR: 6-byte MAC address
+ * Represents the MAC address of the peer for which the TWT session
+ * is being configured. This is used in AP mode to represent the respective
+ * client. In AP mode, this is an optional parameter for response and is
+ * a required parameter for
+ * 1. TWT SET Request
+ * 2. TWT GET Request
+ * 3. TWT TERMINATE Request
+ * 4. TWT SUSPEND Request
+ * In STA mode, this is an optional parameter in request and response for
+ * the above four TWT operations.
*/
enum qca_wlan_vendor_attr_twt_setup {
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0,
@@ -7219,6 +7937,14 @@
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10,
+ /* TWT Response only attributes */
+ QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATUS = 11,
+ QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESP_TYPE = 12,
+ QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF = 13,
+ QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TWT_INFO_ENABLED = 14,
+
+ QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAC_ADDR = 15,
+
/* keep last */
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX =
@@ -7226,24 +7952,80 @@
};
/**
- * enum qca_wlan_vendor_attr_twt_resume: Represents attributes for
+ * enum qca_wlan_vendor_twt_status - Represents the status of the requested
+ * TWT operation
+ *
+ * @QCA_WLAN_VENDOR_TWT_STATUS_OK: TWT request successfully completed
+ * @QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_ENABLED: TWT not enabled
+ * @QCA_WLAN_VENDOR_TWT_STATUS_USED_DIALOG_ID: TWT dialog ID is already used
+ * @QCA_WLAN_VENDOR_TWT_STATUS_SESSION_BUSY: TWT session is busy
+ * @QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST: TWT session does not exist
+ * @QCA_WLAN_VENDOR_TWT_STATUS_NOT_SUSPENDED: TWT session not in suspend state
+ * @QCA_WLAN_VENDOR_TWT_STATUS_INVALID_PARAM: Invalid parameters
+ * @QCA_WLAN_VENDOR_TWT_STATUS_NOT_READY: FW not ready
+ * @QCA_WLAN_VENDOR_TWT_STATUS_NO_RESOURCE: FW resource exhausted
+ * @QCA_WLAN_VENDOR_TWT_STATUS_NO_ACK: Peer AP/STA did not ACK the
+ * request/response frame
+ * @QCA_WLAN_VENDOR_TWT_STATUS_NO_RESPONSE: Peer AP did not send the response
+ * frame
+ * @QCA_WLAN_VENDOR_TWT_STATUS_DENIED: AP did not accept the request
+ * @QCA_WLAN_VENDOR_TWT_STATUS_UNKNOWN_ERROR: Adding TWT dialog failed due to an
+ * unknown reason
+ */
+enum qca_wlan_vendor_twt_status {
+ QCA_WLAN_VENDOR_TWT_STATUS_OK = 0,
+ QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_ENABLED = 1,
+ QCA_WLAN_VENDOR_TWT_STATUS_USED_DIALOG_ID = 2,
+ QCA_WLAN_VENDOR_TWT_STATUS_SESSION_BUSY = 3,
+ QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST = 4,
+ QCA_WLAN_VENDOR_TWT_STATUS_NOT_SUSPENDED = 5,
+ QCA_WLAN_VENDOR_TWT_STATUS_INVALID_PARAM = 6,
+ QCA_WLAN_VENDOR_TWT_STATUS_NOT_READY = 7,
+ QCA_WLAN_VENDOR_TWT_STATUS_NO_RESOURCE = 8,
+ QCA_WLAN_VENDOR_TWT_STATUS_NO_ACK = 9,
+ QCA_WLAN_VENDOR_TWT_STATUS_NO_RESPONSE = 10,
+ QCA_WLAN_VENDOR_TWT_STATUS_DENIED = 11,
+ QCA_WLAN_VENDOR_TWT_STATUS_UNKNOWN_ERROR = 12,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_twt_resume - Represents attributes for
* TWT (Target Wake Time) resume request. These attributes are sent as part of
* %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and
- * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
+ * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Also used by
+ * attributes through %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8)
- * This attribute is used as the SP offset which is the offset from
- * TSF after which the wake happens. The units are in microseconds.
- * If this attribute is not provided, then the value will be set to
- * zero.
+ * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT: Optional (u32)
+ * These attributes are used as the SP offset which is the offset from TSF after
+ * which the wake happens. The units are in microseconds. Please note that
+ * _NEXT_TWT is limited to u8 whereas _NEXT2_TWT takes the u32 data.
+ * _NEXT2_TWT takes the precedence over _NEXT_TWT and thus the recommendation
+ * is to use _NEXT2_TWT. If neither of these attributes is provided, the value
+ * will be set to zero.
*
* @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32)
* This attribute represents the next TWT subfield size.
+ * Value 0 represents 0 bits, 1 represents 32 bits, 2 for 48 bits,
+ * and 4 for 64 bits.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_FLOW_ID: Required (u8).
+ * Flow ID is the unique identifier for each TWT session. This attribute
+ * represents the respective TWT session to resume.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAC_ADDR: 6-byte MAC address
+ * Represents the MAC address of the peer to which TWT Resume is
+ * being sent. This is used in AP mode to represent the respective
+ * client and is a required parameter. In STA mode, this is an optional
+ * parameter
*/
enum qca_wlan_vendor_attr_twt_resume {
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1,
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2,
+ QCA_WLAN_VENDOR_ATTR_TWT_RESUME_FLOW_ID = 3,
+ QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT = 4,
+ QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAC_ADDR = 5,
/* keep last */
QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST,
@@ -7252,6 +8034,28 @@
};
/**
+ * enum qca_wlan_vendor_twt_setup_resp_type - Represents the response type by
+ * the TWT responder
+ *
+ * @QCA_WLAN_VENDOR_TWT_RESP_ALTERNATE: TWT responder suggests TWT
+ * parameters that are different from TWT requesting STA suggested
+ * or demanded TWT parameters
+ * @QCA_WLAN_VENDOR_TWT_RESP_DICTATE: TWT responder demands TWT
+ * parameters that are different from TWT requesting STA TWT suggested
+ * or demanded parameters
+ * @QCA_WLAN_VENDOR_TWT_RESP_REJECT: TWT responder rejects TWT
+ * setup
+ * @QCA_WLAN_VENDOR_TWT_RESP_ACCEPT: TWT responder accepts the TWT
+ * setup.
+ */
+enum qca_wlan_vendor_twt_setup_resp_type {
+ QCA_WLAN_VENDOR_TWT_RESP_ALTERNATE = 1,
+ QCA_WLAN_VENDOR_TWT_RESP_DICTATE = 2,
+ QCA_WLAN_VENDOR_TWT_RESP_REJECT = 3,
+ QCA_WLAN_VENDOR_TWT_RESP_ACCEPT = 4,
+};
+
+/**
* enum qca_wlan_vendor_twt_setup_req_type - Required (u8)
* Represents the setup type being requested for TWT.
* @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT
@@ -7323,10 +8127,42 @@
* enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by
* attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor
* command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG.
+ * @QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL: CFR method using QoS Null frame
+ * @QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE: CFR method using QoS Null frame
+ * with phase
+ * @QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE: CFR method using Probe Response frame
*/
enum qca_wlan_vendor_cfr_method {
- /* CFR method using QOS Null frame */
QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL = 0,
+ QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE = 1,
+ QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE = 2,
+};
+
+/**
+ * enum qca_wlan_vendor_cfr_capture_type - QCA vendor CFR capture type used by
+ * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE.
+ * @QCA_WLAN_VENDOR_CFR_DIRECT_FTM: Filter directed FTM ACK frames.
+ * @QCA_WLAN_VENDOR_CFR_ALL_FTM_ACK: Filter all FTM ACK frames.
+ * @QCA_WLAN_VENDOR_CFR_DIRECT_NDPA_NDP: Filter NDPA NDP directed frames.
+ * @QCA_WLAN_VENDOR_CFR_TA_RA: Filter frames based on TA/RA/Subtype which
+ * is provided by one or more of below attributes:
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER
+ * @QCA_WLAN_CFR_ALL_PACKET: Filter all packets.
+ * @QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL: Filter all NDPA NDP frames.
+ */
+enum qca_wlan_vendor_cfr_capture_type {
+ QCA_WLAN_VENDOR_CFR_DIRECT_FTM = 0,
+ QCA_WLAN_VENDOR_CFR_ALL_FTM_ACK = 1,
+ QCA_WLAN_VENDOR_CFR_DIRECT_NDPA_NDP = 2,
+ QCA_WLAN_VENDOR_CFR_TA_RA = 3,
+ QCA_WLAN_VENDOR_CFR_ALL_PACKET = 4,
+ QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL = 5,
};
/**
@@ -7334,44 +8170,177 @@
* QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer
* Channel Frequency Response capture parameters and enable periodic CFR
* capture.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR: Optional (6-byte MAC address)
+ * MAC address of peer. This is for CFR version 1 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE: Required (flag)
+ * Enable peer CFR capture. This attribute is mandatory to enable peer CFR
+ * capture. If this attribute is not present, peer CFR capture is disabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH: Optional (u8)
+ * BW of measurement, attribute uses the values in enum nl80211_chan_width
+ * Supported values: 20, 40, 80, 80+80, 160.
+ * Note that all targets may not support all bandwidths.
+ * This attribute is mandatory for version 1 if attribute
+ * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY: Optional (u32)
+ * Periodicity of CFR measurement in milliseconds.
+ * Periodicity should be a multiple of Base timer.
+ * Current Base timer value supported is 10 milliseconds (default).
+ * 0 for one shot capture.
+ * This attribute is mandatory for version 1 if attribute
+ * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD: Optional (u8)
+ * Method used to capture Channel Frequency Response.
+ * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method.
+ * This attribute is mandatory for version 1 if attribute
+ * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE: Optional (flag)
+ * Enable periodic CFR capture.
+ * This attribute is mandatory for version 1 to enable Periodic CFR capture.
+ * If this attribute is not present, periodic CFR capture is disabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_VERSION: Optional (u8)
+ * Value is 1 or 2 since there are two versions of CFR capture. Two versions
+ * can't be enabled at same time. This attribute is mandatory if target
+ * support both versions and use one of them.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE_GROUP_BITMAP: Optional (u32)
+ * This attribute is mandatory for version 2 if
+ * QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY is used.
+ * Bits 15:0 bitfield indicates which group is to be enabled.
+ * Bits 31:16 Reserved for future use.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION: Optional (u32)
+ * CFR capture duration in microsecond. This attribute is mandatory for
+ * version 2 if attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL is used.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL: Optional (u32)
+ * CFR capture interval in microsecond. This attribute is mandatory for
+ * version 2 if attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION is used.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE: Optional (u32)
+ * CFR capture type is defined in enum qca_wlan_vendor_cfr_capture_type.
+ * This attribute is mandatory for version 2.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_UL_MU_MASK: Optional (u64)
+ * Bitfield indicating which user in the current UL MU transmissions are
+ * enabled for CFR capture. Bits 36 to 0 indicate user indexes for 37 users in
+ * a UL MU transmission. If bit 0 is set, the CFR capture will happen for user
+ * index 0 in the current UL MU transmission. If bits 0 and 2 are set, CFR
+ * capture for UL MU TX corresponds to user indices 0 and 2. Bits 63:37 are
+ * reserved for future use. This is for CFR version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_FREEZE_TLV_DELAY_COUNT: Optional (u32)
+ * Indicates the number of consecutive RX frames to be skipped before CFR
+ * capture is enabled again. This is for CFR version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TABLE: Nested attribute containing
+ * one or more %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY attributes.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY: Nested attribute containing
+ * the following group attributes:
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER,
+ * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER: Optional (u32)
+ * Target supports multiple groups for some configurations. The group number
+ * can be any value between 0 and 15. This is for CFR version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA: Optional (6-byte MAC address)
+ * Transmitter address which is used to filter frames. This MAC address takes
+ * effect with QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK. This is for CFR
+ * version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA: Optional (6-byte MAC address)
+ * Receiver address which is used to filter frames. This MAC address takes
+ * effect with QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK. This is for CFR
+ * version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK: Optional (6-byte MAC address)
+ * Mask of transmitter address which is used to filter frames. This is for CFR
+ * version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK: Optional (6-byte MAC address)
+ * Mask of receiver address which is used to filter frames. This is for CFR
+ * version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS: Optional (u32)
+ * Indicates frames with a specific NSS will be filtered for CFR capture.
+ * This is for CFR version 2 only. This is a bitmask. Bits 7:0 request CFR
+ * capture to be done for frames matching the NSS specified within this bitmask.
+ * Bits 31:8 are reserved for future use. Bits 7:0 map to NSS:
+ * bit 0 : NSS 1
+ * bit 1 : NSS 2
+ * ...
+ * bit 7 : NSS 8
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW: Optional (u32)
+ * Indicates frames with a specific bandwidth will be filtered for CFR capture.
+ * This is for CFR version 2 only. This is a bitmask. Bits 4:0 request CFR
+ * capture to be done for frames matching the bandwidths specified within this
+ * bitmask. Bits 31:5 are reserved for future use. Bits 4:0 map to bandwidth
+ * numerated in enum nl80211_band (although not all bands may be supported
+ * by a given device).
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER: Optional (u32)
+ * Management frames matching the subtype filter categories will be filtered in
+ * by MAC for CFR capture. This is a bitmask in which each bit represents the
+ * corresponding Management frame subtype value per IEEE Std 802.11-2016,
+ * 9.2.4.1.3 Type and Subtype subfields. For example, Beacon frame control type
+ * is 8 and its value is 1 << 8 = 0x100. This is for CFR version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER: Optional (u32)
+ * Control frames matching the subtype filter categories will be filtered in by
+ * MAC for CFR capture. This is a bitmask in which each bit represents the
+ * corresponding Control frame subtype value per IEEE Std 802.11-2016,
+ * 9.2.4.1.3 Type and Subtype subfields. This is for CFR version 2 only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER: Optional (u32)
+ * Data frames matching the subtype filter categories will be filtered in by
+ * MAC for CFR capture. This is a bitmask in which each bit represents the
+ * corresponding Data frame subtype value per IEEE Std 802.11-2016,
+ * 9.2.4.1.3 Type and Subtype subfields. This is for CFR version 2 only.
*/
enum qca_wlan_vendor_peer_cfr_capture_attr {
QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID = 0,
- /* 6-byte MAC address of the peer.
- * This attribute is mandatory.
- */
QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR = 1,
- /* Enable peer CFR Capture, flag attribute.
- * This attribute is mandatory to enable peer CFR capture.
- * If this attribute is not present, peer CFR capture is disabled.
- */
QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE = 2,
- /* BW of measurement, attribute uses the values in enum nl80211_chan_width
- * Supported values: 20, 40, 80, 80+80, 160.
- * Note that all targets may not support all bandwidths.
- * u8 attribute. This attribute is mandatory if attribute
- * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
- */
QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH = 3,
- /* Periodicity of CFR measurement in msec.
- * Periodicity should be a multiple of Base timer.
- * Current Base timer value supported is 10 msecs (default).
- * 0 for one shot capture. u32 attribute.
- * This attribute is mandatory if attribute
- * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
- */
QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY = 4,
- /* Method used to capture Channel Frequency Response.
- * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method.
- * u8 attribute. This attribute is mandatory if attribute
- * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used.
- */
QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD = 5,
- /* Enable periodic CFR capture, flag attribute.
- * This attribute is mandatory to enable Periodic CFR capture.
- * If this attribute is not present, periodic CFR capture is disabled.
- */
QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE = 6,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_VERSION = 7,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE_GROUP_BITMAP = 8,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION = 9,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL = 10,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE = 11,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_UL_MU_MASK = 12,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_FREEZE_TLV_DELAY_COUNT = 13,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TABLE = 14,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY = 15,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER = 16,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA = 17,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA = 18,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK = 19,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK = 20,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS = 21,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW = 22,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER = 23,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER = 24,
+ QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER = 25,
/* Keep last */
QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST,
@@ -8019,10 +8988,14 @@
* enum qca_wlan_vendor_attr_oem_data_params - Used by the vendor command/event
* QCA_NL80211_VENDOR_SUBCMD_OEM_DATA.
*
- * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA: The binary blob for the vendor
- * command/event QCA_NL80211_VENDOR_SUBCMD_OEM_DATA are carried through this
- * attribute.
- * NLA_BINARY attribute, the max size is 1024 bytes.
+ * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA: This NLA_BINARY attribute is
+ * used to set/query the data to/from the firmware. On query, the same
+ * attribute is used to carry the respective data in the reply sent by the
+ * driver to userspace. The request to set/query the data and the format of the
+ * respective data from the firmware are embedded in the attribute. The
+ * maximum size of the attribute payload is 1024 bytes.
+ * Userspace has to set the QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED
+ * attribute when the data is queried from the firmware.
*
* @QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO: The binary blob will be routed
* based on this field. This optional attribute is included to specify whether
@@ -8031,11 +9004,16 @@
* command/event.
* This u8 attribute is used to carry information for the device type using
* values defined by enum qca_vendor_oem_device_type.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED: This NLA_FLAG attribute
+ * is set when the userspace queries data from the firmware. This attribute
+ * should not be set when userspace sets the OEM data to the firmware.
*/
enum qca_wlan_vendor_attr_oem_data_params {
QCA_WLAN_VENDOR_ATTR_OEM_DATA_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA = 1,
QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO = 2,
+ QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED = 3,
/* keep last */
QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST,
@@ -8353,6 +9331,42 @@
* when queried in the connected state. When queried in the disconnected
* state, this corresponds to the latest ANI level at the instance of
* disconnection.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_IES: Binary attribute containing
+ * the raw information elements from Beacon frames. Represents the Beacon frames
+ * of the current BSS in the connected state. When queried in the disconnected
+ * state, these IEs correspond to the last connected BSSID.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PROBE_RESP_IES: Binary attribute
+ * containing the raw information elements from Probe Response frames.
+ * Represents the Probe Response frames of the current BSS in the connected
+ * state. When queried in the disconnected state, these IEs correspond to the
+ * last connected BSSID.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON: u32, Driver
+ * disconnect reason for the last disconnection if the disconnection is
+ * triggered from the host driver. The values are referred from
+ * enum qca_disconnect_reason_codes.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_MIC_ERROR_COUNT: u32, used in STA mode
+ * only. This represents the number of group addressed robust management frames
+ * received from this station with an invalid MIC or a missing MME when PMF is
+ * enabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_REPLAY_COUNT: u32, used in STA mode
+ * only. This represents the number of group addressed robust management frames
+ * received from this station with the packet number less than or equal to the
+ * last received packet number when PMF is enabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_MIC_ERROR_COUNT: u32, used in STA
+ * mode only. This represents the number of Beacon frames received from this
+ * station with an invalid MIC or a missing MME when beacon protection is
+ * enabled.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_REPLAY_COUNT: u32, used in STA mode
+ * only. This represents number of Beacon frames received from this station with
+ * the packet number less than or equal to the last received packet number when
+ * beacon protection is enabled.
*/
enum qca_wlan_vendor_attr_get_sta_info {
QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_INVALID = 0,
@@ -8391,6 +9405,13 @@
QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER = 33,
QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER = 34,
QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL = 35,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_IES = 36,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PROBE_RESP_IES = 37,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON = 38,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_MIC_ERROR_COUNT = 39,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_REPLAY_COUNT = 40,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_MIC_ERROR_COUNT = 41,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_REPLAY_COUNT = 42,
/* keep last */
QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST,
@@ -8398,4 +9419,427 @@
QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST - 1,
};
+/**
+ * enum qca_wlan_vendor_attr_update_sta_info - Defines attributes
+ * used by QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO vendor command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS: Type is NLA_UNSPEC.
+ * Used in STA mode. This attribute represents the list of channel center
+ * frequencies in MHz (u32) the station has learnt during the last connection
+ * or roaming attempt. This information shall not signify the channels for
+ * an explicit scan request from the user space. Host drivers can update this
+ * information to the user space in both connected and disconnected state.
+ * In the disconnected state this information shall signify the channels
+ * scanned in the last connection/roam attempt that lead to the disconnection.
+ */
+enum qca_wlan_vendor_attr_update_sta_info {
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS = 1,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_disconnect_reason_codes - Specifies driver disconnect reason codes.
+ * Used when the driver triggers the STA to disconnect from the AP.
+ *
+ * @QCA_DISCONNECT_REASON_UNSPECIFIED: The host driver triggered the
+ * disconnection with the AP due to unspecified reasons.
+ *
+ * @QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE: The host driver triggered the
+ * disconnection with the AP due to a roaming failure. This roaming is triggered
+ * internally (host driver/firmware).
+ *
+ * @QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE: The driver disconnected from
+ * the AP when the user/external triggered roaming fails.
+ *
+ * @QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE: This reason code is used
+ * by the host driver whenever gateway reachability failure is detected and the
+ * driver disconnects with AP.
+ *
+ * @QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA: The driver disconnected from
+ * the AP on a channel switch announcement from it with an unsupported channel.
+ *
+ * @QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR: On a concurrent AP start
+ * with indoor channels disabled and if the STA is connected on one of these
+ * disabled channels, the host driver disconnected the STA with this reason
+ * code.
+ *
+ * @QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED: Disconnection due to an
+ * explicit request from the user to disable the current operating channel.
+ *
+ * @QCA_DISCONNECT_REASON_DEVICE_RECOVERY: STA disconnected from the AP due to
+ * the internal host driver/firmware recovery.
+ *
+ * @QCA_DISCONNECT_REASON_KEY_TIMEOUT: The driver triggered the disconnection on
+ * a timeout for the key installations from the user space.
+ *
+ * @QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE: The dDriver disconnected the
+ * STA on a band change request from the user space to a different band from the
+ * current operation channel/band.
+ *
+ * @QCA_DISCONNECT_REASON_IFACE_DOWN: The STA disconnected from the AP on an
+ * interface down trigger from the user space.
+ *
+ * @QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL: The host driver disconnected the
+ * STA on getting continuous transmission failures for multiple Data frames.
+ *
+ * @QCA_DISCONNECT_REASON_PEER_INACTIVITY: The STA does a keep alive
+ * notification to the AP by transmitting NULL/G-ARP frames. This disconnection
+ * represents inactivity from AP on such transmissions.
+
+ * @QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT: This reason code is used on
+ * disconnection when SA Query times out (AP does not respond to SA Query).
+ *
+ * @QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE: The host driver disconnected the
+ * STA on missing the beacons continuously from the AP.
+ *
+ * @QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE: Disconnection due to STA not
+ * able to move to the channel mentioned by the AP in CSA.
+ *
+ * @QCA_DISCONNECT_REASON_USER_TRIGGERED: User triggered disconnection.
+ */
+enum qca_disconnect_reason_codes {
+ QCA_DISCONNECT_REASON_UNSPECIFIED = 0,
+ QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE = 1,
+ QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE = 2,
+ QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE = 3,
+ QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA = 4,
+ QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR = 5,
+ QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED = 6,
+ QCA_DISCONNECT_REASON_DEVICE_RECOVERY = 7,
+ QCA_DISCONNECT_REASON_KEY_TIMEOUT = 8,
+ QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE = 9,
+ QCA_DISCONNECT_REASON_IFACE_DOWN = 10,
+ QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL = 11,
+ QCA_DISCONNECT_REASON_PEER_INACTIVITY = 12,
+ QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT = 13,
+ QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE = 14,
+ QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE = 15,
+ QCA_DISCONNECT_REASON_USER_TRIGGERED = 16,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_driver_disconnect_reason - Defines attributes
+ * used by %QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON vendor command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE: u32 attribute.
+ * This attribute represents the driver specific reason codes (local
+ * driver/firmware initiated reasons for disconnection) defined
+ * in enum qca_disconnect_reason_codes.
+ */
+enum qca_wlan_vendor_attr_driver_disconnect_reason {
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE = 1,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_MAX =
+ QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_tspec_operation - Operation of the config TSPEC request
+ *
+ * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION.
+ */
+enum qca_wlan_tspec_operation {
+ QCA_WLAN_TSPEC_ADD = 0,
+ QCA_WLAN_TSPEC_DEL = 1,
+ QCA_WLAN_TSPEC_GET = 2,
+};
+
+/**
+ * enum qca_wlan_tspec_direction - Direction in TSPEC
+ * As what is defined in IEEE Std 802.11-2016, Table 9-139.
+ *
+ * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION.
+ */
+enum qca_wlan_tspec_direction {
+ QCA_WLAN_TSPEC_DIRECTION_UPLINK = 0,
+ QCA_WLAN_TSPEC_DIRECTION_DOWNLINK = 1,
+ QCA_WLAN_TSPEC_DIRECTION_DIRECT = 2,
+ QCA_WLAN_TSPEC_DIRECTION_BOTH = 3,
+};
+
+/**
+ * enum qca_wlan_tspec_ack_policy - MAC acknowledgement policy in TSPEC
+ * As what is defined in IEEE Std 802.11-2016, Table 9-141.
+ *
+ * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY.
+ */
+enum qca_wlan_tspec_ack_policy {
+ QCA_WLAN_TSPEC_NORMAL_ACK = 0,
+ QCA_WLAN_TSPEC_NO_ACK = 1,
+ /* Reserved */
+ QCA_WLAN_TSPEC_BLOCK_ACK = 3,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_config_tspec - Defines attributes
+ * used by %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC vendor command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION:
+ * u8 attribute. Specify the TSPEC operation of this request. Possible values
+ * are defined in enum qca_wlan_tspec_operation.
+ * Mandatory attribute for all kinds of config TSPEC requests.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_TSID:
+ * u8 attribute. TS ID. Possible values are 0-7.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD, QCA_WLAN_TSPEC_DEL,
+ * QCA_WLAN_TSPEC_GET. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION:
+ * u8 attribute. Direction of data carried by the TS. Possible values are
+ * defined in enum qca_wlan_tspec_direction.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_APSD:
+ * Flag attribute. Indicate whether APSD is enabled for the traffic associated
+ * with the TS. set - enabled, not set - disabled.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_USER_PRIORITY:
+ * u8 attribute. User priority to be used for the transport of MSDUs/A-MSDUs
+ * belonging to this TS. Possible values are 0-7.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY:
+ * u8 attribute. Indicate whether MAC acknowledgements are required for
+ * MPDUs/A-MSDUs belonging to this TS and the form of those acknowledgements.
+ * Possible values are defined in enum qca_wlan_tspec_ack_policy.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_NOMINAL_MSDU_SIZE:
+ * u16 attribute. Specify the nominal size in bytes of MSDUs/A-MSDUs
+ * belonging to this TS.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAXIMUM_MSDU_SIZE:
+ * u16 attribute. Specify the maximum size in bytes of MSDUs/A-MSDUs
+ * belonging to this TS.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MIN_SERVICE_INTERVAL:
+ * u32 attribute. Specify the minimum interval in microseconds between the
+ * start of two successive SPs.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX_SERVICE_INTERVAL:
+ * u32 attribute. Specify the maximum interval in microseconds between the
+ * start of two successive SPs.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INACTIVITY_INTERVAL:
+ * u32 attribute. Specify the minimum interval in microseconds that can elapse
+ * without arrival or transfer of an MPDU belonging to the TS before this TS
+ * is deleted by the MAC entity at the HC.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SUSPENSION_INTERVAL:
+ * u32 attribute. Specify the minimum interval in microseconds that can elapse
+ * without arrival or transfer of an MSDU belonging to the TS before the
+ * generation of successive QoS(+)CF-Poll is stopped for this TS. A value of
+ * 0xFFFFFFFF disables the suspension interval. The value of the suspension
+ * interval is always less than or equal to the inactivity interval.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_DATA_RATE:
+ * u32 attribute. Indicate the lowest data rate in bps specified at the MAC
+ * SAP for transport of MSDUs or A-MSDUs belonging to this TS within the
+ * bounds of this TSPEC.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MEAN_DATA_RATE:
+ * u32 attribute. Indicate the average data rate in bps specified at the MAC
+ * SAP for transport of MSDUs or A-MSDUs belonging to this TS within the
+ * bounds of this TSPEC.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_PEAK_DATA_RATE:
+ * u32 attribute. Indicate the maximum allowable data rate in bps specified at
+ * the MAC SAP for transport of MSDUs or A-MSDUs belonging to this TS within
+ * the bounds of this TSPEC.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_BURST_SIZE:
+ * u32 attribute. Specify the maximum burst size in bytes of the MSDUs/A-MSDUs
+ * belonging to this TS that arrive at the MAC SAP at the peak data rate. A
+ * value of 0 indicates that there are no bursts.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_PHY_RATE:
+ * u32 attribute. Indicate the minimum PHY rate in bps for transport of
+ * MSDUs/A-MSDUs belonging to this TS within the bounds of this TSPEC.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SURPLUS_BANDWIDTH_ALLOWANCE:
+ * u16 attribute. Specify the excess allocation of time (and bandwidth) over
+ * and above the stated application rates required to transport an MSDU/A-MSDU
+ * belonging to the TS in this TSPEC.
+ * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute.
+ */
+enum qca_wlan_vendor_attr_config_tspec {
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION = 1,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_TSID = 2,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION = 3,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_APSD = 4,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_USER_PRIORITY = 5,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY = 6,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_NOMINAL_MSDU_SIZE = 7,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAXIMUM_MSDU_SIZE = 8,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MIN_SERVICE_INTERVAL = 9,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX_SERVICE_INTERVAL = 10,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INACTIVITY_INTERVAL = 11,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SUSPENSION_INTERVAL = 12,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_DATA_RATE = 13,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MEAN_DATA_RATE = 14,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_PEAK_DATA_RATE = 15,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_BURST_SIZE = 16,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_PHY_RATE = 17,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SURPLUS_BANDWIDTH_ALLOWANCE = 18,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX =
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_oci_override_frame_type - OCI override frame type
+ * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_REQ: SA Query Request frame
+ * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_RESP: SA Query Response frame
+ * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FT_REASSOC_REQ: FT Reassociation Request
+ * frame
+ * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FILS_REASSOC_REQ: FILS Reassociation
+ * Request frame.
+ */
+enum qca_wlan_vendor_oci_override_frame_type {
+ QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_REQ = 1,
+ QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_RESP = 2,
+ QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FT_REASSOC_REQ = 3,
+ QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FILS_REASSOC_REQ = 4,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_oci_override: Represents attributes for
+ * OCI override request. These attributes are used inside nested attribute
+ * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OCI_OVERRIDE in QCA vendor command
+ * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FRAME_TYPE: Required attribute, u8.
+ * Values from enum qca_wlan_vendor_oci_override_frame_type used in this
+ * attribute to specify the frame type in which the OCI is to be overridden.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FREQUENCY: Required (u32)
+ * OCI frequency (in MHz) to override in the specified frame type.
+ */
+enum qca_wlan_vendor_attr_oci_override {
+ QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FRAME_TYPE = 1,
+ QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FREQUENCY = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_MAX =
+ QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_medium_assess_type - Type of medium assess request
+ *
+ * Values for %QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE.
+ */
+enum qca_wlan_medium_assess_type {
+ QCA_WLAN_MEDIUM_ASSESS_CCA = 0,
+ QCA_WLAN_MEDIUM_ASSESS_CONGESTION_REPORT = 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_medium_assess - Attributes used by
+ * %QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS vendor command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE:
+ * u8 attribute. Mandatory in all kinds of medium assess requests/responses.
+ * Specify the type of medium assess request and indicate its type in response.
+ * Possible values are defined in enum qca_wlan_medium_assess_type.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_PERIOD:
+ * u32 attribute. Mandatory in CCA request.
+ * Specify the assessment period in terms of seconds. Assessment result will be
+ * sent as the response to the CCA request after the assessment period.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TOTAL_CYCLE_COUNT:
+ * u32 attribute. Mandatory in response to CCA request.
+ * Total timer tick count of the assessment cycle.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IDLE_COUNT:
+ * u32 attribute. Mandatory in response to CCA request.
+ * Timer tick count of idle time in the assessment cycle.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IBSS_RX_COUNT:
+ * u32 attribute. Mandatory in response to CCA request.
+ * Timer tick count of Intra BSS traffic RX time in the assessment cycle.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_OBSS_RX_COUNT:
+ * u32 attribute. Mandatory in response to CCA request.
+ * Timer tick count of Overlapping BSS traffic RX time in the assessment cycle.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX_IBSS_RSSI:
+ * s32 attribute. Mandatory in response to CCA request.
+ * Maximum RSSI of Intra BSS traffic in the assessment cycle.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MIN_IBSS_RSSI:
+ * s32 attribute. Mandatory in response to CCA request.
+ * Minimum RSSI of Intra BSS traffic in the assessment cycle.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_ENABLE:
+ * u8 attribute. Mandatory in congestion report request.
+ * 1-enable 0-disable.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_THRESHOLD:
+ * u8 attribute. Mandatory in congestion report enable request and will be
+ * ignored if present in congestion report disable request. Possible values are
+ * 0-100. A vendor event QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS with the type
+ * QCA_WLAN_MEDIUM_ASSESS_CONGESTION_REPORT will be sent to userspace if
+ * congestion percentage reaches the configured threshold.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_INTERVAL:
+ * u8 attribute. Optional in congestion report enable request and will be
+ * ignored if present in congestion report disable request.
+ * Specify the interval of congestion report event in terms of seconds. Possible
+ * values are 1-255. Default value 1 will be used if this attribute is omitted
+ * or using invalid values.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_PERCENTAGE:
+ * u8 attribute. Mandatory in congestion report event.
+ * Indicate the actual congestion percentage. Possible values are 0-100.
+ */
+enum qca_wlan_vendor_attr_medium_assess {
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE = 1,
+
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_PERIOD = 2,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TOTAL_CYCLE_COUNT = 3,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IDLE_COUNT = 4,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IBSS_RX_COUNT = 5,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_OBSS_RX_COUNT = 6,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX_IBSS_RSSI = 7,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MIN_IBSS_RSSI = 8,
+
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_ENABLE = 9,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_THRESHOLD = 10,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_INTERVAL = 11,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_PERCENTAGE = 12,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX =
+ QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_AFTER_LAST - 1,
+};
+
#endif /* QCA_VENDOR_H */