| ########################### Start of libnfc-st.conf ########################### |
| |
| ############################################################################### |
| # Application options |
| APPL_TRACE_LEVEL=0x05 |
| # HAL trace flag: 0x00200000 |
| # HAL NDLC trace flag: 0x00400000 |
| PROTOCOL_TRACE_LEVEL=0x00600000 |
| |
| ############################################################################### |
| # File used for NFA storage |
| NFA_STORAGE="/data/nfc" |
| |
| ############################################################################### |
| # Keep the nfa storage file. |
| PRESERVE_STORAGE=1 |
| |
| ############################################################################### |
| # Force UICC to only listen to the following technology(s). |
| # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. |
| # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B. |
| # NOTE 1: P2P_LISTEN_TECH_MASK has also an impact on programmed listen mask |
| # NOTE 2: If using android 4.4, the listen mode A is always programmed. |
| UICC_LISTEN_TECH_MASK=0x00 |
| |
| ############################################################################### |
| # Inform the system of the maximum number of SE supported. |
| # Minimum value is 1 has the UICC may always be used. |
| # eSE may not be used depending on phone configuration. |
| MAX_NUMBER_OF_SE=0x3 |
| |
| ############################################################################### |
| # AID for Empty Select command |
| # If specified, this AID will be substituted when an Empty SELECT command is |
| # detected. The first byte is the length of the AID. Maximum length is 16. |
| AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00} |
| |
| ############################################################################### |
| # Force tag polling for the following technology(s). |
| # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. |
| # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | |
| # NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693. |
| # |
| # Notable bits: |
| # NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ |
| # NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */ |
| # NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ |
| # NFA_TECHNOLOGY_MASK_V 0x08 /* NFC Technology V */ |
| # NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */ |
| # NFA_TECHNOLOGY_MASK_ACTIVE 0x40 /* NFC Technology ACM active mode */ |
| POLLING_TECH_MASK=0x6F |
| |
| ############################################################################### |
| # Force P2P to only listen for the following technology(s). |
| # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. |
| # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ACTIVE. |
| P2P_LISTEN_TECH_MASK=0x45 |
| |
| ############################################################################### |
| # When screen is turned OFF, specify the desired CE mode to the controller. |
| # 0: No card-emulation; DEFAULT |
| # 1: Screen-off card-emulation enabled |
| CE_ON_SCREEN_OFF_STATE=1 |
| |
| ############################################################################### |
| # In Switch OFF mode (phone switched-off), specify the desired CE mode to |
| # the controller. |
| # 0: No card-emulation; DEFAULT |
| # 1: Switch-off card-emulation enabled |
| CE_ON_SWITCH_OFF_STATE=1 |
| |
| ############################################################################### |
| # Choose the presence-check algorithm for type-4 tag. If not defined, |
| # the default value is 1. |
| # 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm |
| # 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block |
| # 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate |
| # 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0 |
| # 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3 |
| PRESENCE_CHECK_ALGORITHM=3 |
| |
| ############################################################################### |
| # Name of the NCI HAL module to use |
| # If unset, falls back to nfc_nci.bcm2079x |
| NCI_HAL_MODULE="nfc_nci.st21nfc" |
| |
| ############################################################################### |
| # White list to be set at startup. |
| DEVICE_HOST_WHITE_LIST={2:c0} |
| |
| ############################################################################### |
| # When screen is turned off, specify the desired power state of the controller. |
| # 0: power-off-sleep state; DEFAULT |
| # 1: full-power state |
| # 2: screen-off card-emulation (CE4/CE3/CE1 modes are used) |
| SCREEN_OFF_POWER_STATE=1 |
| |
| ############################################################################### |
| # Default Secure Element route id |
| DEFAULT_OFFHOST_ROUTE=0x81 |
| |
| ############################################################################### |
| # Default Secure Element route id for F technology |
| DEFAULT_NFCF_ROUTE=0x0 |
| |
| ############################################################################### |
| # AID_MATCHING constants |
| # AID_MATCHING_EXACT_ONLY 0x00 |
| # AID_MATCHING_EXACT_OR_PREFIX 0x01 |
| # AID_MATCHING_PREFIX_ONLY 0x02 |
| AID_MATCHING_MODE=0x1 |
| |
| ############################################################################### |
| # ST HAL log level |
| STNFC_HAL_LOGLEVEL=3 |