| /****************************************************************************** |
| * |
| * Copyright (C) 1999-2012 Broadcom Corporation |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at: |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| * |
| ******************************************************************************/ |
| |
| #ifndef HCIMSGS_H |
| #define HCIMSGS_H |
| |
| #include "bt_target.h" |
| #include "hcidefs.h" |
| #include "bt_types.h" |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| void bte_main_hci_send(BT_HDR *p_msg, uint16_t event); |
| void bte_main_lpm_allow_bt_device_sleep(void); |
| |
| /* Message by message.... */ |
| |
| extern void btsnd_hcic_inquiry(const LAP inq_lap, uint8_t duration, |
| uint8_t response_cnt); |
| |
| #define HCIC_PARAM_SIZE_INQUIRY 5 |
| |
| |
| #define HCIC_INQ_INQ_LAP_OFF 0 |
| #define HCIC_INQ_DUR_OFF 3 |
| #define HCIC_INQ_RSP_CNT_OFF 4 |
| /* Inquiry */ |
| |
| /* Inquiry Cancel */ |
| extern void btsnd_hcic_inq_cancel(void); |
| |
| #define HCIC_PARAM_SIZE_INQ_CANCEL 0 |
| |
| /* Periodic Inquiry Mode */ |
| extern void btsnd_hcic_per_inq_mode(uint16_t max_period, uint16_t min_period, |
| const LAP inq_lap, uint8_t duration, |
| uint8_t response_cnt); |
| |
| #define HCIC_PARAM_SIZE_PER_INQ_MODE 9 |
| |
| #define HCI_PER_INQ_MAX_INTRVL_OFF 0 |
| #define HCI_PER_INQ_MIN_INTRVL_OFF 2 |
| #define HCI_PER_INQ_INQ_LAP_OFF 4 |
| #define HCI_PER_INQ_DURATION_OFF 7 |
| #define HCI_PER_INQ_RSP_CNT_OFF 8 |
| /* Periodic Inquiry Mode */ |
| |
| /* Exit Periodic Inquiry Mode */ |
| extern void btsnd_hcic_exit_per_inq(void); |
| |
| #define HCIC_PARAM_SIZE_EXIT_PER_INQ 0 |
| /* Create Connection */ |
| extern void btsnd_hcic_create_conn(BD_ADDR dest, uint16_t packet_types, |
| uint8_t page_scan_rep_mode, |
| uint8_t page_scan_mode, |
| uint16_t clock_offset, |
| uint8_t allow_switch); |
| |
| #define HCIC_PARAM_SIZE_CREATE_CONN 13 |
| |
| #define HCIC_CR_CONN_BD_ADDR_OFF 0 |
| #define HCIC_CR_CONN_PKT_TYPES_OFF 6 |
| #define HCIC_CR_CONN_REP_MODE_OFF 8 |
| #define HCIC_CR_CONN_PAGE_SCAN_MODE_OFF 9 |
| #define HCIC_CR_CONN_CLK_OFF_OFF 10 |
| #define HCIC_CR_CONN_ALLOW_SWITCH_OFF 12 |
| /* Create Connection */ |
| |
| /* Disconnect */ |
| extern void btsnd_hcic_disconnect(uint16_t handle, uint8_t reason); |
| |
| #define HCIC_PARAM_SIZE_DISCONNECT 3 |
| |
| #define HCI_DISC_HANDLE_OFF 0 |
| #define HCI_DISC_REASON_OFF 2 |
| /* Disconnect */ |
| |
| #if (BTM_SCO_INCLUDED == TRUE) |
| /* Add SCO Connection */ |
| extern void btsnd_hcic_add_SCO_conn (uint16_t handle, uint16_t packet_types); |
| #endif /* BTM_SCO_INCLUDED */ |
| |
| #define HCIC_PARAM_SIZE_ADD_SCO_CONN 4 |
| |
| #define HCI_ADD_SCO_HANDLE_OFF 0 |
| #define HCI_ADD_SCO_PACKET_TYPES_OFF 2 |
| /* Add SCO Connection */ |
| |
| /* Create Connection Cancel */ |
| extern void btsnd_hcic_create_conn_cancel(BD_ADDR dest); |
| |
| #define HCIC_PARAM_SIZE_CREATE_CONN_CANCEL 6 |
| |
| #define HCIC_CR_CONN_CANCEL_BD_ADDR_OFF 0 |
| /* Create Connection Cancel */ |
| |
| /* Accept Connection Request */ |
| extern void btsnd_hcic_accept_conn (BD_ADDR bd_addr, uint8_t role); |
| |
| #define HCIC_PARAM_SIZE_ACCEPT_CONN 7 |
| |
| #define HCI_ACC_CONN_BD_ADDR_OFF 0 |
| #define HCI_ACC_CONN_ROLE_OFF 6 |
| /* Accept Connection Request */ |
| |
| /* Reject Connection Request */ |
| extern void btsnd_hcic_reject_conn (BD_ADDR bd_addr, uint8_t reason); |
| |
| #define HCIC_PARAM_SIZE_REJECT_CONN 7 |
| |
| #define HCI_REJ_CONN_BD_ADDR_OFF 0 |
| #define HCI_REJ_CONN_REASON_OFF 6 |
| /* Reject Connection Request */ |
| |
| /* Link Key Request Reply */ |
| extern void btsnd_hcic_link_key_req_reply (BD_ADDR bd_addr, |
| LINK_KEY link_key); |
| |
| #define HCIC_PARAM_SIZE_LINK_KEY_REQ_REPLY 22 |
| |
| #define HCI_LINK_KEY_REPLY_BD_ADDR_OFF 0 |
| #define HCI_LINK_KEY_REPLY_LINK_KEY_OFF 6 |
| /* Link Key Request Reply */ |
| |
| /* Link Key Request Neg Reply */ |
| extern void btsnd_hcic_link_key_neg_reply (BD_ADDR bd_addr); |
| |
| #define HCIC_PARAM_SIZE_LINK_KEY_NEG_REPLY 6 |
| |
| #define HCI_LINK_KEY_NEG_REP_BD_ADR_OFF 0 |
| /* Link Key Request Neg Reply */ |
| |
| /* PIN Code Request Reply */ |
| extern void btsnd_hcic_pin_code_req_reply (BD_ADDR bd_addr, |
| uint8_t pin_code_len, |
| PIN_CODE pin_code); |
| |
| #define HCIC_PARAM_SIZE_PIN_CODE_REQ_REPLY 23 |
| |
| #define HCI_PIN_CODE_REPLY_BD_ADDR_OFF 0 |
| #define HCI_PIN_CODE_REPLY_PIN_LEN_OFF 6 |
| #define HCI_PIN_CODE_REPLY_PIN_CODE_OFF 7 |
| /* PIN Code Request Reply */ |
| |
| /* Link Key Request Neg Reply */ |
| extern void btsnd_hcic_pin_code_neg_reply (BD_ADDR bd_addr); |
| |
| #define HCIC_PARAM_SIZE_PIN_CODE_NEG_REPLY 6 |
| |
| #define HCI_PIN_CODE_NEG_REP_BD_ADR_OFF 0 |
| /* Link Key Request Neg Reply */ |
| |
| /* Change Connection Type */ |
| extern void btsnd_hcic_change_conn_type (uint16_t handle, uint16_t packet_types); |
| |
| #define HCIC_PARAM_SIZE_CHANGE_CONN_TYPE 4 |
| |
| #define HCI_CHNG_PKT_TYPE_HANDLE_OFF 0 |
| #define HCI_CHNG_PKT_TYPE_PKT_TYPE_OFF 2 |
| /* Change Connection Type */ |
| |
| #define HCIC_PARAM_SIZE_CMD_HANDLE 2 |
| |
| #define HCI_CMD_HANDLE_HANDLE_OFF 0 |
| |
| extern void btsnd_hcic_auth_request (uint16_t handle); /* Authentication Request */ |
| |
| /* Set Connection Encryption */ |
| extern void btsnd_hcic_set_conn_encrypt (uint16_t handle, bool enable); |
| #define HCIC_PARAM_SIZE_SET_CONN_ENCRYPT 3 |
| |
| |
| #define HCI_SET_ENCRYPT_HANDLE_OFF 0 |
| #define HCI_SET_ENCRYPT_ENABLE_OFF 2 |
| /* Set Connection Encryption */ |
| |
| /* Remote Name Request */ |
| extern void btsnd_hcic_rmt_name_req (BD_ADDR bd_addr, |
| uint8_t page_scan_rep_mode, |
| uint8_t page_scan_mode, |
| uint16_t clock_offset); |
| |
| #define HCIC_PARAM_SIZE_RMT_NAME_REQ 10 |
| |
| #define HCI_RMT_NAME_BD_ADDR_OFF 0 |
| #define HCI_RMT_NAME_REP_MODE_OFF 6 |
| #define HCI_RMT_NAME_PAGE_SCAN_MODE_OFF 7 |
| #define HCI_RMT_NAME_CLK_OFF_OFF 8 |
| /* Remote Name Request */ |
| |
| /* Remote Name Request Cancel */ |
| extern void btsnd_hcic_rmt_name_req_cancel(BD_ADDR bd_addr); |
| |
| #define HCIC_PARAM_SIZE_RMT_NAME_REQ_CANCEL 6 |
| |
| #define HCI_RMT_NAME_CANCEL_BD_ADDR_OFF 0 |
| /* Remote Name Request Cancel */ |
| |
| extern void btsnd_hcic_rmt_features_req(uint16_t handle); /* Remote Features Request */ |
| |
| /* Remote Extended Features */ |
| extern void btsnd_hcic_rmt_ext_features(uint16_t handle, uint8_t page_num); |
| |
| #define HCIC_PARAM_SIZE_RMT_EXT_FEATURES 3 |
| |
| #define HCI_RMT_EXT_FEATURES_HANDLE_OFF 0 |
| #define HCI_RMT_EXT_FEATURES_PAGE_NUM_OFF 2 |
| /* Remote Extended Features */ |
| |
| |
| extern void btsnd_hcic_rmt_ver_req(uint16_t handle); /* Remote Version Info Request */ |
| extern void btsnd_hcic_read_rmt_clk_offset(uint16_t handle); /* Remote Clock Offset */ |
| extern void btsnd_hcic_read_lmp_handle(uint16_t handle); /* Remote LMP Handle */ |
| |
| extern void btsnd_hcic_setup_esco_conn (uint16_t handle, |
| uint32_t tx_bw, uint32_t rx_bw, |
| uint16_t max_latency, uint16_t voice, |
| uint8_t retrans_effort, |
| uint16_t packet_types); |
| #define HCIC_PARAM_SIZE_SETUP_ESCO 17 |
| |
| #define HCI_SETUP_ESCO_HANDLE_OFF 0 |
| #define HCI_SETUP_ESCO_TX_BW_OFF 2 |
| #define HCI_SETUP_ESCO_RX_BW_OFF 6 |
| #define HCI_SETUP_ESCO_MAX_LAT_OFF 10 |
| #define HCI_SETUP_ESCO_VOICE_OFF 12 |
| #define HCI_SETUP_ESCO_RETRAN_EFF_OFF 14 |
| #define HCI_SETUP_ESCO_PKT_TYPES_OFF 15 |
| |
| |
| extern void btsnd_hcic_accept_esco_conn (BD_ADDR bd_addr, |
| uint32_t tx_bw, uint32_t rx_bw, |
| uint16_t max_latency, |
| uint16_t content_fmt, |
| uint8_t retrans_effort, |
| uint16_t packet_types); |
| #define HCIC_PARAM_SIZE_ACCEPT_ESCO 21 |
| |
| #define HCI_ACCEPT_ESCO_BDADDR_OFF 0 |
| #define HCI_ACCEPT_ESCO_TX_BW_OFF 6 |
| #define HCI_ACCEPT_ESCO_RX_BW_OFF 10 |
| #define HCI_ACCEPT_ESCO_MAX_LAT_OFF 14 |
| #define HCI_ACCEPT_ESCO_VOICE_OFF 16 |
| #define HCI_ACCEPT_ESCO_RETRAN_EFF_OFF 18 |
| #define HCI_ACCEPT_ESCO_PKT_TYPES_OFF 19 |
| |
| |
| extern void btsnd_hcic_reject_esco_conn (BD_ADDR bd_addr, uint8_t reason); |
| #define HCIC_PARAM_SIZE_REJECT_ESCO 7 |
| |
| #define HCI_REJECT_ESCO_BDADDR_OFF 0 |
| #define HCI_REJECT_ESCO_REASON_OFF 6 |
| |
| /* Hold Mode */ |
| extern void btsnd_hcic_hold_mode(uint16_t handle, uint16_t max_hold_period, |
| uint16_t min_hold_period); |
| |
| #define HCIC_PARAM_SIZE_HOLD_MODE 6 |
| |
| #define HCI_HOLD_MODE_HANDLE_OFF 0 |
| #define HCI_HOLD_MODE_MAX_PER_OFF 2 |
| #define HCI_HOLD_MODE_MIN_PER_OFF 4 |
| /* Hold Mode */ |
| |
| /* Sniff Mode */ |
| extern void btsnd_hcic_sniff_mode(uint16_t handle, |
| uint16_t max_sniff_period, |
| uint16_t min_sniff_period, |
| uint16_t sniff_attempt, |
| uint16_t sniff_timeout); |
| |
| #define HCIC_PARAM_SIZE_SNIFF_MODE 10 |
| |
| |
| #define HCI_SNIFF_MODE_HANDLE_OFF 0 |
| #define HCI_SNIFF_MODE_MAX_PER_OFF 2 |
| #define HCI_SNIFF_MODE_MIN_PER_OFF 4 |
| #define HCI_SNIFF_MODE_ATTEMPT_OFF 6 |
| #define HCI_SNIFF_MODE_TIMEOUT_OFF 8 |
| /* Sniff Mode */ |
| |
| extern void btsnd_hcic_exit_sniff_mode(uint16_t handle); /* Exit Sniff Mode */ |
| |
| /* Park Mode */ |
| extern void btsnd_hcic_park_mode (uint16_t handle, |
| uint16_t beacon_max_interval, |
| uint16_t beacon_min_interval); |
| |
| #define HCIC_PARAM_SIZE_PARK_MODE 6 |
| |
| #define HCI_PARK_MODE_HANDLE_OFF 0 |
| #define HCI_PARK_MODE_MAX_PER_OFF 2 |
| #define HCI_PARK_MODE_MIN_PER_OFF 4 |
| /* Park Mode */ |
| |
| extern void btsnd_hcic_exit_park_mode(uint16_t handle); /* Exit Park Mode */ |
| |
| /* QoS Setup */ |
| extern void btsnd_hcic_qos_setup (uint16_t handle, uint8_t flags, |
| uint8_t service_type, |
| uint32_t token_rate, uint32_t peak, |
| uint32_t latency, uint32_t delay_var); |
| |
| #define HCIC_PARAM_SIZE_QOS_SETUP 20 |
| |
| #define HCI_QOS_HANDLE_OFF 0 |
| #define HCI_QOS_FLAGS_OFF 2 |
| #define HCI_QOS_SERVICE_TYPE_OFF 3 |
| #define HCI_QOS_TOKEN_RATE_OFF 4 |
| #define HCI_QOS_PEAK_BANDWIDTH_OFF 8 |
| #define HCI_QOS_LATENCY_OFF 12 |
| #define HCI_QOS_DELAY_VAR_OFF 16 |
| /* QoS Setup */ |
| |
| /* Switch Role Request */ |
| extern void btsnd_hcic_switch_role (BD_ADDR bd_addr, uint8_t role); |
| |
| #define HCIC_PARAM_SIZE_SWITCH_ROLE 7 |
| |
| #define HCI_SWITCH_BD_ADDR_OFF 0 |
| #define HCI_SWITCH_ROLE_OFF 6 |
| /* Switch Role Request */ |
| |
| /* Write Policy Settings */ |
| extern void btsnd_hcic_write_policy_set(uint16_t handle, uint16_t settings); |
| |
| #define HCIC_PARAM_SIZE_WRITE_POLICY_SET 4 |
| |
| #define HCI_WRITE_POLICY_HANDLE_OFF 0 |
| #define HCI_WRITE_POLICY_SETTINGS_OFF 2 |
| /* Write Policy Settings */ |
| |
| /* Write Default Policy Settings */ |
| extern void btsnd_hcic_write_def_policy_set(uint16_t settings); |
| |
| #define HCIC_PARAM_SIZE_WRITE_DEF_POLICY_SET 2 |
| |
| #define HCI_WRITE_DEF_POLICY_SETTINGS_OFF 0 |
| /* Write Default Policy Settings */ |
| |
| /****************************************** |
| * Lisbon Features |
| ******************************************/ |
| #if (BTM_SSR_INCLUDED == TRUE) |
| /* Sniff Subrating */ |
| extern void btsnd_hcic_sniff_sub_rate(uint16_t handle, uint16_t max_lat, |
| uint16_t min_remote_lat, |
| uint16_t min_local_lat); |
| |
| #define HCIC_PARAM_SIZE_SNIFF_SUB_RATE 8 |
| |
| #define HCI_SNIFF_SUB_RATE_HANDLE_OFF 0 |
| #define HCI_SNIFF_SUB_RATE_MAX_LAT_OFF 2 |
| #define HCI_SNIFF_SUB_RATE_MIN_REM_LAT_OFF 4 |
| #define HCI_SNIFF_SUB_RATE_MIN_LOC_LAT_OFF 6 |
| /* Sniff Subrating */ |
| |
| #else /* BTM_SSR_INCLUDED == FALSE */ |
| |
| #define btsnd_hcic_sniff_sub_rate(handle, max_lat, min_remote_lat, min_local_lat) false |
| |
| #endif /* BTM_SSR_INCLUDED */ |
| |
| /* Extended Inquiry Response */ |
| extern void btsnd_hcic_write_ext_inquiry_response(void *buffer, uint8_t fec_req); |
| |
| #define HCIC_PARAM_SIZE_EXT_INQ_RESP 241 |
| |
| #define HCIC_EXT_INQ_RESP_FEC_OFF 0 |
| #define HCIC_EXT_INQ_RESP_RESPONSE 1 |
| /* IO Capabilities Response */ |
| extern void btsnd_hcic_io_cap_req_reply (BD_ADDR bd_addr, uint8_t capability, |
| uint8_t oob_present, uint8_t auth_req); |
| |
| #define HCIC_PARAM_SIZE_IO_CAP_RESP 9 |
| |
| #define HCI_IO_CAP_BD_ADDR_OFF 0 |
| #define HCI_IO_CAPABILITY_OFF 6 |
| #define HCI_IO_CAP_OOB_DATA_OFF 7 |
| #define HCI_IO_CAP_AUTH_REQ_OFF 8 |
| |
| /* IO Capabilities Req Neg Reply */ |
| extern void btsnd_hcic_io_cap_req_neg_reply (BD_ADDR bd_addr, uint8_t err_code); |
| |
| #define HCIC_PARAM_SIZE_IO_CAP_NEG_REPLY 7 |
| |
| #define HCI_IO_CAP_NR_BD_ADDR_OFF 0 |
| #define HCI_IO_CAP_NR_ERR_CODE 6 |
| |
| /* Read Local OOB Data */ |
| extern void btsnd_hcic_read_local_oob_data (void); |
| |
| #define HCIC_PARAM_SIZE_R_LOCAL_OOB 0 |
| |
| |
| extern void btsnd_hcic_user_conf_reply (BD_ADDR bd_addr, bool is_yes); |
| |
| #define HCIC_PARAM_SIZE_UCONF_REPLY 6 |
| |
| #define HCI_USER_CONF_BD_ADDR_OFF 0 |
| |
| |
| extern void btsnd_hcic_user_passkey_reply (BD_ADDR bd_addr, uint32_t value); |
| |
| #define HCIC_PARAM_SIZE_U_PKEY_REPLY 10 |
| |
| #define HCI_USER_PASSKEY_BD_ADDR_OFF 0 |
| #define HCI_USER_PASSKEY_VALUE_OFF 6 |
| |
| |
| extern void btsnd_hcic_user_passkey_neg_reply (BD_ADDR bd_addr); |
| |
| #define HCIC_PARAM_SIZE_U_PKEY_NEG_REPLY 6 |
| |
| #define HCI_USER_PASSKEY_NEG_BD_ADDR_OFF 0 |
| |
| /* Remote OOB Data Request Reply */ |
| extern void btsnd_hcic_rem_oob_reply (BD_ADDR bd_addr, uint8_t *p_c, |
| uint8_t *p_r); |
| |
| #define HCIC_PARAM_SIZE_REM_OOB_REPLY 38 |
| |
| #define HCI_REM_OOB_DATA_BD_ADDR_OFF 0 |
| #define HCI_REM_OOB_DATA_C_OFF 6 |
| #define HCI_REM_OOB_DATA_R_OFF 22 |
| |
| /* Remote OOB Data Request Negative Reply */ |
| extern void btsnd_hcic_rem_oob_neg_reply (BD_ADDR bd_addr); |
| |
| #define HCIC_PARAM_SIZE_REM_OOB_NEG_REPLY 6 |
| |
| #define HCI_REM_OOB_DATA_NEG_BD_ADDR_OFF 0 |
| |
| /* Read Tx Power Level */ |
| extern void btsnd_hcic_read_inq_tx_power (void); |
| |
| #define HCIC_PARAM_SIZE_R_TX_POWER 0 |
| |
| /* Read Default Erroneous Data Reporting */ |
| extern void btsnd_hcic_read_default_erroneous_data_rpt (void); |
| |
| #define HCIC_PARAM_SIZE_R_ERR_DATA_RPT 0 |
| |
| #if (L2CAP_NON_FLUSHABLE_PB_INCLUDED == TRUE) |
| extern void btsnd_hcic_enhanced_flush (uint16_t handle, uint8_t packet_type); |
| |
| #define HCIC_PARAM_SIZE_ENHANCED_FLUSH 3 |
| #endif |
| |
| |
| extern void btsnd_hcic_send_keypress_notif (BD_ADDR bd_addr, uint8_t notif); |
| |
| #define HCIC_PARAM_SIZE_SEND_KEYPRESS_NOTIF 7 |
| |
| #define HCI_SEND_KEYPRESS_NOTIF_BD_ADDR_OFF 0 |
| #define HCI_SEND_KEYPRESS_NOTIF_NOTIF_OFF 6 |
| |
| /**** end of Simple Pairing Commands ****/ |
| |
| /* Store Current Settings */ |
| #define MAX_FILT_COND (sizeof (BD_ADDR) + 1) |
| |
| extern void btsnd_hcic_set_event_filter(uint8_t filt_type, |
| uint8_t filt_cond_type, |
| uint8_t *filt_cond, |
| uint8_t filt_cond_len); |
| |
| #define HCIC_PARAM_SIZE_SET_EVT_FILTER 9 |
| |
| #define HCI_FILT_COND_FILT_TYPE_OFF 0 |
| #define HCI_FILT_COND_COND_TYPE_OFF 1 |
| #define HCI_FILT_COND_FILT_OFF 2 |
| /* Set Event Filter */ |
| |
| /* Delete Stored Key */ |
| extern void btsnd_hcic_delete_stored_key (BD_ADDR bd_addr, bool delete_all_flag); |
| |
| #define HCIC_PARAM_SIZE_DELETE_STORED_KEY 7 |
| |
| #define HCI_DELETE_KEY_BD_ADDR_OFF 0 |
| #define HCI_DELETE_KEY_ALL_FLAG_OFF 6 |
| /* Delete Stored Key */ |
| |
| /* Change Local Name */ |
| extern void btsnd_hcic_change_name(BD_NAME name); |
| |
| #define HCIC_PARAM_SIZE_CHANGE_NAME BD_NAME_LEN |
| |
| #define HCI_CHANGE_NAME_NAME_OFF 0 |
| /* Change Local Name */ |
| |
| |
| #define HCIC_PARAM_SIZE_READ_CMD 0 |
| |
| #define HCIC_PARAM_SIZE_WRITE_PARAM1 1 |
| |
| #define HCIC_WRITE_PARAM1_PARAM_OFF 0 |
| |
| #define HCIC_PARAM_SIZE_WRITE_PARAM2 2 |
| |
| #define HCIC_WRITE_PARAM2_PARAM_OFF 0 |
| |
| #define HCIC_PARAM_SIZE_WRITE_PARAM3 3 |
| |
| #define HCIC_WRITE_PARAM3_PARAM_OFF 0 |
| |
| #define HCIC_PARAM_SIZE_SET_AFH_CHANNELS 10 |
| |
| extern void btsnd_hcic_write_pin_type(uint8_t type); /* Write PIN Type */ |
| extern void btsnd_hcic_write_auto_accept(uint8_t flag); /* Write Auto Accept */ |
| extern void btsnd_hcic_read_name (void); /* Read Local Name */ |
| extern void btsnd_hcic_write_page_tout(uint16_t timeout); /* Write Page Timout */ |
| extern void btsnd_hcic_write_scan_enable(uint8_t flag); /* Write Scan Enable */ |
| extern void btsnd_hcic_write_pagescan_cfg(uint16_t interval, |
| uint16_t window); /* Write Page Scan Activity */ |
| |
| #define HCIC_PARAM_SIZE_WRITE_PAGESCAN_CFG 4 |
| |
| #define HCI_SCAN_CFG_INTERVAL_OFF 0 |
| #define HCI_SCAN_CFG_WINDOW_OFF 2 |
| /* Write Page Scan Activity */ |
| |
| /* Write Inquiry Scan Activity */ |
| extern void btsnd_hcic_write_inqscan_cfg(uint16_t interval, uint16_t window); |
| |
| #define HCIC_PARAM_SIZE_WRITE_INQSCAN_CFG 4 |
| |
| #define HCI_SCAN_CFG_INTERVAL_OFF 0 |
| #define HCI_SCAN_CFG_WINDOW_OFF 2 |
| /* Write Inquiry Scan Activity */ |
| |
| extern void btsnd_hcic_write_auth_enable(uint8_t flag); /* Write Authentication Enable */ |
| extern void btsnd_hcic_write_dev_class(DEV_CLASS dev); /* Write Class of Device */ |
| extern void btsnd_hcic_write_voice_settings(uint16_t flags); /* Write Voice Settings */ |
| |
| /* Host Controller to Host flow control */ |
| #define HCI_HOST_FLOW_CTRL_OFF 0 |
| #define HCI_HOST_FLOW_CTRL_ACL_ON 1 |
| #define HCI_HOST_FLOW_CTRL_SCO_ON 2 |
| #define HCI_HOST_FLOW_CTRL_BOTH_ON 3 |
| |
| extern void btsnd_hcic_write_auto_flush_tout(uint16_t handle, |
| uint16_t timeout); /* Write Retransmit Timout */ |
| |
| #define HCIC_PARAM_SIZE_WRITE_AUTO_FLUSH_TOUT 4 |
| |
| #define HCI_FLUSH_TOUT_HANDLE_OFF 0 |
| #define HCI_FLUSH_TOUT_TOUT_OFF 2 |
| |
| extern void btsnd_hcic_read_tx_power(uint16_t handle, uint8_t type); /* Read Tx Power */ |
| |
| #define HCIC_PARAM_SIZE_READ_TX_POWER 3 |
| |
| #define HCI_READ_TX_POWER_HANDLE_OFF 0 |
| #define HCI_READ_TX_POWER_TYPE_OFF 2 |
| |
| /* Read transmit power level parameter */ |
| #define HCI_READ_CURRENT 0x00 |
| #define HCI_READ_MAXIMUM 0x01 |
| |
| extern void btsnd_hcic_host_num_xmitted_pkts (uint8_t num_handles, |
| uint16_t *handle, |
| uint16_t *num_pkts); /* Set Host Buffer Size */ |
| |
| #define HCIC_PARAM_SIZE_NUM_PKTS_DONE_SIZE sizeof(btmsg_hcic_num_pkts_done_t) |
| |
| #define MAX_DATA_HANDLES 10 |
| |
| #define HCI_PKTS_DONE_NUM_HANDLES_OFF 0 |
| #define HCI_PKTS_DONE_HANDLE_OFF 1 |
| #define HCI_PKTS_DONE_NUM_PKTS_OFF 3 |
| |
| /* Write Link Supervision Timeout */ |
| extern void btsnd_hcic_write_link_super_tout(uint8_t local_controller_id, uint16_t handle, uint16_t timeout); |
| |
| #define HCIC_PARAM_SIZE_WRITE_LINK_SUPER_TOUT 4 |
| |
| #define HCI_LINK_SUPER_TOUT_HANDLE_OFF 0 |
| #define HCI_LINK_SUPER_TOUT_TOUT_OFF 2 |
| /* Write Link Supervision Timeout */ |
| |
| extern void btsnd_hcic_write_cur_iac_lap (uint8_t num_cur_iac, |
| LAP * const iac_lap); /* Write Current IAC LAP */ |
| |
| #define MAX_IAC_LAPS 0x40 |
| |
| #define HCI_WRITE_IAC_LAP_NUM_OFF 0 |
| #define HCI_WRITE_IAC_LAP_LAP_OFF 1 |
| /* Write Current IAC LAP */ |
| |
| extern void btsnd_hcic_get_link_quality (uint16_t handle); /* Get Link Quality */ |
| extern void btsnd_hcic_read_rssi (uint16_t handle); /* Read RSSI */ |
| extern void btsnd_hcic_enable_test_mode (void); /* Enable Device Under Test Mode */ |
| extern void btsnd_hcic_write_pagescan_type(uint8_t type); /* Write Page Scan Type */ |
| extern void btsnd_hcic_write_inqscan_type(uint8_t type); /* Write Inquiry Scan Type */ |
| extern void btsnd_hcic_write_inquiry_mode(uint8_t type); /* Write Inquiry Mode */ |
| |
| #define HCI_DATA_HANDLE_MASK 0x0FFF |
| |
| #define HCID_GET_HANDLE_EVENT(p) (uint16_t)((*((uint8_t *)((p) + 1) + (p)->offset) + \ |
| (*((uint8_t *)((p) + 1) + (p)->offset + 1) << 8))) |
| |
| #define HCID_GET_HANDLE(u16) (uint16_t)((u16) & HCI_DATA_HANDLE_MASK) |
| |
| #define HCI_DATA_EVENT_MASK 3 |
| #define HCI_DATA_EVENT_OFFSET 12 |
| #define HCID_GET_EVENT(u16) (uint8_t)(((u16) >> HCI_DATA_EVENT_OFFSET) & HCI_DATA_EVENT_MASK) |
| |
| #define HCI_DATA_BCAST_MASK 3 |
| #define HCI_DATA_BCAST_OFFSET 10 |
| #define HCID_GET_BCAST(u16) (uint8_t)(((u16) >> HCI_DATA_BCAST_OFFSET) & HCI_DATA_BCAST_MASK) |
| |
| #define HCID_GET_ACL_LEN(p) (uint16_t)((*((uint8_t *)((p) + 1) + (p)->offset + 2) + \ |
| (*((uint8_t *)((p) + 1) + (p)->offset + 3) << 8))) |
| |
| #define HCID_HEADER_SIZE 4 |
| |
| #define HCID_GET_SCO_LEN(p) (*((uint8_t *)((p) + 1) + (p)->offset + 2)) |
| |
| extern void btsnd_hcic_vendor_spec_cmd (void *buffer, uint16_t opcode, |
| uint8_t len, uint8_t *p_data, |
| void *p_cmd_cplt_cback); |
| |
| /******************************************************************************* |
| * BLE Commands |
| * Note: "local_controller_id" is for transport, not counted in HCI |
| * message size |
| ******************************************************************************/ |
| #define HCIC_BLE_RAND_DI_SIZE 8 |
| #define HCIC_BLE_ENCRYT_KEY_SIZE 16 |
| #define HCIC_BLE_IRK_SIZE 16 |
| |
| #define HCIC_PARAM_SIZE_SET_USED_FEAT_CMD 8 |
| #define HCIC_PARAM_SIZE_WRITE_RANDOM_ADDR_CMD 6 |
| #define HCIC_PARAM_SIZE_BLE_WRITE_ADV_PARAMS 15 |
| #define HCIC_PARAM_SIZE_BLE_WRITE_SCAN_RSP 31 |
| #define HCIC_PARAM_SIZE_WRITE_ADV_ENABLE 1 |
| #define HCIC_PARAM_SIZE_BLE_WRITE_SCAN_PARAM 7 |
| #define HCIC_PARAM_SIZE_BLE_WRITE_SCAN_ENABLE 2 |
| #define HCIC_PARAM_SIZE_BLE_CREATE_LL_CONN 25 |
| #define HCIC_PARAM_SIZE_BLE_CREATE_CONN_CANCEL 0 |
| #define HCIC_PARAM_SIZE_CLEAR_WHITE_LIST 0 |
| #define HCIC_PARAM_SIZE_ADD_WHITE_LIST 7 |
| #define HCIC_PARAM_SIZE_REMOVE_WHITE_LIST 7 |
| #define HCIC_PARAM_SIZE_BLE_UPD_LL_CONN_PARAMS 14 |
| #define HCIC_PARAM_SIZE_SET_HOST_CHNL_CLASS 5 |
| #define HCIC_PARAM_SIZE_READ_CHNL_MAP 2 |
| #define HCIC_PARAM_SIZE_BLE_READ_REMOTE_FEAT 2 |
| #define HCIC_PARAM_SIZE_BLE_ENCRYPT 32 |
| #define HCIC_PARAM_SIZE_BLE_RAND 0 |
| #define HCIC_PARAM_SIZE_WRITE_LE_HOST_SUPPORTED 2 |
| |
| #define HCIC_BLE_RAND_DI_SIZE 8 |
| #define HCIC_BLE_ENCRYT_KEY_SIZE 16 |
| #define HCIC_PARAM_SIZE_BLE_START_ENC (4 + HCIC_BLE_RAND_DI_SIZE + HCIC_BLE_ENCRYT_KEY_SIZE) |
| #define HCIC_PARAM_SIZE_LTK_REQ_REPLY (2 + HCIC_BLE_ENCRYT_KEY_SIZE) |
| #define HCIC_PARAM_SIZE_LTK_REQ_NEG_REPLY 2 |
| #define HCIC_BLE_CHNL_MAP_SIZE 5 |
| #define HCIC_PARAM_SIZE_BLE_WRITE_ADV_DATA 31 |
| |
| #define HCIC_PARAM_SIZE_BLE_ADD_DEV_RESOLVING_LIST (7 + HCIC_BLE_IRK_SIZE * 2) |
| #define HCIC_PARAM_SIZE_BLE_RM_DEV_RESOLVING_LIST 7 |
| #define HCIC_PARAM_SIZE_BLE_CLEAR_RESOLVING_LIST 0 |
| #define HCIC_PARAM_SIZE_BLE_READ_RESOLVING_LIST_SIZE 0 |
| #define HCIC_PARAM_SIZE_BLE_READ_RESOLVABLE_ADDR_PEER 7 |
| #define HCIC_PARAM_SIZE_BLE_READ_RESOLVABLE_ADDR_LOCAL 7 |
| #define HCIC_PARAM_SIZE_BLE_SET_ADDR_RESOLUTION_ENABLE 1 |
| #define HCIC_PARAM_SIZE_BLE_SET_RAND_PRIV_ADDR_TIMOUT 2 |
| #define HCIC_PARAM_SIZE_BLE_SET_DATA_LENGTH 6 |
| #define HCIC_PARAM_SIZE_BLE_WRITE_EXTENDED_SCAN_PARAM 11 |
| |
| /* ULP HCI command */ |
| extern void btsnd_hcic_ble_set_evt_mask (BT_EVENT_MASK event_mask); |
| |
| extern void btsnd_hcic_ble_read_buffer_size (void); |
| |
| extern void btsnd_hcic_ble_read_local_spt_feat (void); |
| |
| extern void btsnd_hcic_ble_set_local_used_feat (uint8_t feat_set[8]); |
| |
| extern void btsnd_hcic_ble_set_random_addr (BD_ADDR random_addr); |
| |
| extern void btsnd_hcic_ble_write_adv_params (uint16_t adv_int_min, uint16_t adv_int_max, |
| uint8_t adv_type, uint8_t addr_type_own, |
| uint8_t addr_type_dir, BD_ADDR direct_bda, |
| uint8_t channel_map, uint8_t adv_filter_policy); |
| |
| extern void btsnd_hcic_ble_read_adv_chnl_tx_power (void); |
| |
| extern void btsnd_hcic_ble_set_adv_data (uint8_t data_len, uint8_t *p_data); |
| |
| extern void btsnd_hcic_ble_set_scan_rsp_data (uint8_t data_len, uint8_t *p_scan_rsp); |
| |
| extern void btsnd_hcic_ble_set_adv_enable (uint8_t adv_enable); |
| |
| extern void btsnd_hcic_ble_set_scan_params (uint8_t scan_type, |
| uint16_t scan_int, uint16_t scan_win, |
| uint8_t addr_type, uint8_t scan_filter_policy); |
| |
| extern void btsnd_hcic_ble_set_scan_enable (uint8_t scan_enable, uint8_t duplicate); |
| |
| extern void btsnd_hcic_ble_create_ll_conn (uint16_t scan_int, uint16_t scan_win, |
| uint8_t init_filter_policy, uint8_t addr_type_peer, BD_ADDR bda_peer, uint8_t addr_type_own, |
| uint16_t conn_int_min, uint16_t conn_int_max, uint16_t conn_latency, uint16_t conn_timeout, |
| uint16_t min_ce_len, uint16_t max_ce_len); |
| |
| extern void btsnd_hcic_ble_create_conn_cancel (void); |
| |
| extern void btsnd_hcic_ble_read_white_list_size (void); |
| |
| extern void btsnd_hcic_ble_clear_white_list (void); |
| |
| extern void btsnd_hcic_ble_add_white_list (uint8_t addr_type, BD_ADDR bda); |
| |
| extern void btsnd_hcic_ble_remove_from_white_list (uint8_t addr_type, BD_ADDR bda); |
| |
| extern void btsnd_hcic_ble_upd_ll_conn_params (uint16_t handle, uint16_t conn_int_min, uint16_t conn_int_max, |
| uint16_t conn_latency, uint16_t conn_timeout, uint16_t min_len, uint16_t max_len); |
| |
| extern void btsnd_hcic_ble_set_host_chnl_class (uint8_t chnl_map[HCIC_BLE_CHNL_MAP_SIZE]); |
| |
| extern void btsnd_hcic_ble_read_chnl_map (uint16_t handle); |
| |
| extern void btsnd_hcic_ble_read_remote_feat ( uint16_t handle); |
| |
| extern void btsnd_hcic_ble_encrypt (uint8_t* key, uint8_t key_len, uint8_t* plain_text, uint8_t pt_len, void *p_cmd_cplt_cback); |
| |
| extern void btsnd_hcic_ble_rand (void *p_cmd_cplt_cback); |
| |
| extern void btsnd_hcic_ble_start_enc ( uint16_t handle, |
| uint8_t rand[HCIC_BLE_RAND_DI_SIZE], |
| uint16_t ediv, uint8_t ltk[HCIC_BLE_ENCRYT_KEY_SIZE]); |
| |
| extern void btsnd_hcic_ble_ltk_req_reply (uint16_t handle, uint8_t ltk[HCIC_BLE_ENCRYT_KEY_SIZE]); |
| |
| extern void btsnd_hcic_ble_ltk_req_neg_reply (uint16_t handle); |
| |
| extern void btsnd_hcic_ble_read_supported_states (void); |
| |
| extern void btsnd_hcic_ble_write_host_supported (uint8_t le_host_spt, uint8_t simul_le_host_spt); |
| |
| extern void btsnd_hcic_ble_read_host_supported (void); |
| |
| extern void btsnd_hcic_ble_receiver_test(uint8_t rx_freq); |
| |
| extern void btsnd_hcic_ble_transmitter_test(uint8_t tx_freq, uint8_t test_data_len, |
| uint8_t payload); |
| extern void btsnd_hcic_ble_test_end(void); |
| |
| #if (BLE_LLT_INCLUDED == TRUE) |
| |
| #define HCIC_PARAM_SIZE_BLE_RC_PARAM_REQ_REPLY 14 |
| extern void btsnd_hcic_ble_rc_param_req_reply(uint16_t handle, |
| uint16_t conn_int_min, uint16_t conn_int_max, |
| uint16_t conn_latency, uint16_t conn_timeout, |
| uint16_t min_ce_len, uint16_t max_ce_len); |
| |
| #define HCIC_PARAM_SIZE_BLE_RC_PARAM_REQ_NEG_REPLY 3 |
| extern void btsnd_hcic_ble_rc_param_req_neg_reply(uint16_t handle, uint8_t reason); |
| |
| #endif /* BLE_LLT_INCLUDED */ |
| |
| extern void btsnd_hcic_ble_set_data_length(uint16_t conn_handle, uint16_t tx_octets, |
| uint16_t tx_time); |
| |
| extern void btsnd_hcic_ble_add_device_resolving_list (uint8_t addr_type_peer, |
| BD_ADDR bda_peer, |
| uint8_t irk_peer[HCIC_BLE_IRK_SIZE], |
| uint8_t irk_local[HCIC_BLE_IRK_SIZE]); |
| |
| extern void btsnd_hcic_ble_rm_device_resolving_list (uint8_t addr_type_peer, |
| BD_ADDR bda_peer); |
| |
| extern void btsnd_hcic_ble_clear_resolving_list (void); |
| |
| extern void btsnd_hcic_ble_read_resolvable_addr_peer (uint8_t addr_type_peer, |
| BD_ADDR bda_peer); |
| |
| extern void btsnd_hcic_ble_read_resolvable_addr_local (uint8_t addr_type_peer, |
| BD_ADDR bda_peer); |
| |
| extern void btsnd_hcic_ble_set_addr_resolution_enable (uint8_t addr_resolution_enable); |
| |
| extern void btsnd_hcic_ble_set_rand_priv_addr_timeout (uint16_t rpa_timout); |
| |
| extern void btsnd_hcic_read_authenticated_payload_tout(uint16_t handle); |
| |
| extern void btsnd_hcic_write_authenticated_payload_tout(uint16_t handle, |
| uint16_t timeout); |
| |
| #define HCIC_PARAM_SIZE_WRITE_AUTHENT_PAYLOAD_TOUT 4 |
| |
| #define HCI__WRITE_AUTHENT_PAYLOAD_TOUT_HANDLE_OFF 0 |
| #define HCI__WRITE_AUTHENT_PAYLOAD_TOUT_TOUT_OFF 2 |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif |