prima: Support for NAT keep alive packets
qcacld-2.0 to pronto propagation
This is the host driver implementation to support sending
fixed NAT keep alive packets to WiFi Network.
1. WifiHal issues start send packet with ip_packet, ip_packet_len,
destination mac address and period. Host driver populates the data
and sends WMI message to firmware to configure the tx pattern.
2. WifiHal upon sending stop packet, host driver sends delete
tx pattern to the firmware.
Additional changes are done to pass the pattern bitmap to WDA.
Change-Id: I58309d1c58ff0ba9bcf86c31ac2a7eccfa3a7f8f
CRs-Fixed: 915690
diff --git a/Kbuild b/Kbuild
index 3c13ce8..a9c8de3 100644
--- a/Kbuild
+++ b/Kbuild
@@ -14,36 +14,39 @@
endif
ifeq ($(KERNEL_BUILD), 0)
- # These are configurable via Kconfig for kernel-based builds
- # Need to explicitly configure for Android-based builds
+# These are configurable via Kconfig for kernel-based builds
+# Need to explicitly configure for Android-based builds
- #Flag to enable BlueTooth AMP feature
- CONFIG_PRIMA_WLAN_BTAMP := n
+#Flag to enable BlueTooth AMP feature
+ CONFIG_PRIMA_WLAN_BTAMP := n
- #Flag to enable Legacy Fast Roaming(LFR)
- CONFIG_PRIMA_WLAN_LFR := y
+#Flag to enable Legacy Fast Roaming(LFR)
+ CONFIG_PRIMA_WLAN_LFR := y
- #JB kernel has PMKSA patches, hence enabling this flag
- CONFIG_PRIMA_WLAN_OKC := y
+#JB kernel has PMKSA patches, hence enabling this flag
+ CONFIG_PRIMA_WLAN_OKC := y
- # JB kernel has CPU enablement patches, so enable
- CONFIG_PRIMA_WLAN_11AC_HIGH_TP := y
+# JB kernel has CPU enablement patches, so enable
+ CONFIG_PRIMA_WLAN_11AC_HIGH_TP := y
- #Flag to enable TDLS feature
- CONFIG_QCOM_TDLS := y
+#Flag to enable TDLS feature
+ CONFIG_QCOM_TDLS := y
- #Flag to enable Fast Transition (11r) feature
- CONFIG_QCOM_VOWIFI_11R := y
+#Flag to enable Fast Transition (11r) feature
+ CONFIG_QCOM_VOWIFI_11R := y
- #Flag to enable Protected Managment Frames (11w) feature
- ifneq ($(CONFIG_PRONTO_WLAN),)
- CONFIG_WLAN_FEATURE_11W := y
- endif
+#Flag to enable Protected Managment Frames (11w) feature
+ifneq ($(CONFIG_PRONTO_WLAN),)
+ CONFIG_WLAN_FEATURE_11W := y
+ endif
- #Flag to enable new Linux Regulatory implementation
- CONFIG_ENABLE_LINUX_REG := y
+#Flag to enable new Linux Regulatory implementation
+ CONFIG_ENABLE_LINUX_REG := y
-endif
+#Flag to enable offload packets feature
+ CONFIG_WLAN_OFFLOAD_PACKETS := y
+
+ endif
# To enable CONFIG_QCOM_ESE_UPLOAD, dependent config
# CONFIG_QCOM_ESE must be enabled.
@@ -666,6 +669,10 @@
# Fix build for GCC 4.7
EXTRA_CFLAGS += -Wno-maybe-uninitialized -Wno-unused-function
+ifeq ($(CONFIG_WLAN_OFFLOAD_PACKETS),y)
+CDEFINES += -DWLAN_FEATURE_OFFLOAD_PACKETS
+endif
+
KBUILD_CPPFLAGS += $(CDEFINES)
# Module information used by KBuild framework