prima: WLAN Driver Release 3.2.0.9
diff --git a/firmware_bin/WCNSS_qcom_cfg.ini b/firmware_bin/WCNSS_qcom_cfg.ini
index 4a867da..cb32d0e 100644
--- a/firmware_bin/WCNSS_qcom_cfg.ini
+++ b/firmware_bin/WCNSS_qcom_cfg.ini
@@ -1,98 +1,157 @@
# This file allows user to override the factory
+
# defaults for the WLAN Driver
+
# Enable IMPS or not
gEnableImps=1
# Enable/Disable Idle Scan
+
gEnableIdleScan=0
+
# Increase sleep duration (seconds) during IMPS
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0
+
# Enable BMPS or not
gEnableBmps=1
# Enable suspend or not
+
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
+
gEnableSuspend=3
+
# Phy Mode (auto, b, g, n, etc)
+# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
gDot11Mode=0
+
# Handoff Enable(1) Disable(0)
+
gEnableHandoff=0
+
# CSR Roaming Enable(1) Disable(0)
+
gRoamingTime=0
+
# Assigned MAC Addresses - This will be used until NV items are in place
+
# Each byte of MAC address is represented in Hex format as XX
+
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
+
Intf3MacAddress=000AF58989FC
+
# UAPSD service interval for VO,VI, BE, BK traffic
+
InfraUapsdVoSrvIntv=0
+
InfraUapsdViSrvIntv=0
+
InfraUapsdBeSrvIntv=0
+
InfraUapsdBkSrvIntv=0
+
# Disable RSSI FW filtering
+
gEnableFWRssiMonitoring=0
+
# Make 1x1 the default antenna configuration
+
gNumRxAnt=1
+
# Beacon filtering frequency (unit in beacon intervals)
+
gNthBeaconFilter=50
+
# Enable WAPI or not
+
# WAPIIsEnabled=0
+
# Flags to filter Mcast abd Bcast RX packets.
+
# Value 0: No filtering, 1: Filter all Multicast.
+
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
+
McastBcastFilter=3
+
#Flag to enable HostARPOffload feature or not
+
hostArpOffload=0
+
#SoftAP Related Parameters
+
# AP MAc addr
-gAPMacAddr=000AF58989EF
+
+gAPMacAddr=000AF589dcab
+
# 802.11n Protection flag
+
gEnableApProt=1
+
#Enable OBSS protection
+
gEnableApOBSSProt=0
+
#Enable/Disable UAPSD for SoftAP
-gEnableApUapsd=1
+
+gEnableApUapsd=0
+
# Fixed Rate
+
gFixedRate=0
+
# Maximum Tx power
+
# gTxPowerCap=30
+
# Fragmentation Threshold
+
# gFragmentationThreshold=2346
+
# RTS threshold
+
RTSThreshold=2347
+
# Intra-BSS forward
+
gDisableIntraBssFwd=0
+
# WMM Enable/Disable
+
WmmIsEnabled=0
+
# 802.11d support
+
g11dSupportEnabled=1
# CCX Support and fast transition
@@ -117,83 +176,162 @@
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
#the RSSI of the new/roamable AP should be for roaming
-RoamRssiDiff=0
+RoamRssiDiff=5
# SAP Country code
+
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
+
# Example
+
# US Indoor, USI
+
# Korea Outdoor, KRO
+
# Japan without optional byte, JP
+
# France without optional byte, FR
+
#gAPCntryCode=USI
+
#Short Guard Interval Enable/disable
+
gShortGI20Mhz=1
+
gShortGI40Mhz=1
+
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
+
gAPAutoShutOff=0
+
# SAP auto channel selection configuration
+
# 0 = disable auto channel selection
+
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
+
gApAutoChannelSelection=0
+
# Listen Energy Detect Mode Configuration
+
# Valid values 0-128
+
# 128 means disable Energy Detect feature
+
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
+
# 10-128 are reserved.
+
# The EDET threshold mapping is as follows in 3dB step:
+
# 0 = -60 dBm
+
# 1 = -63 dBm
+
# 2 = -66 dBm
+
# ...
+
# 7 = -81 dBm
+
# 8 = -84 dBm
+
# 9 = -87 dBm
+
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
+
#
+
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
+
#
+
gEnablePhyAgcListenMode=128
+
#Preferred channel to start BT AMP AP mode (0 means, any channel)
+
BtAmpPreferredChannel=0
+
#Preferred band (both or 2.4 only or 5 only)
+
BandCapability=0
+
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
+
enableBeaconEarlyTermination=0
+
beaconEarlyTerminationWakeInterval=3
+
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
+
gEnableBtAmp=0
+
#SOFTAP Channel Range selection
+
gAPChannelSelectStartChannel=1
+
gAPChannelSelectEndChannel=11
+
#SOFTAP Channel Range selection Operating band
+
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
+
gAPChannelSelectOperatingBand=0
+
+#Channel Bonding
+gChannelBondingMode5GHz=6
+
+
#Enable Keep alive with non-zero period value
+
#gStaKeepAlivePeriod = 30
+
#If set will start with active scan after driver load, otherwise will start with
+
#passive scan to find out the domain
-gEnableBypass11d=1
+
+#gEnableBypass11d=1
+
#If set to 0, will not scan DFS channels
+
gEnableDFSChnlScan=1
-# Enable logp/SSR
+
+gVhtChannelWidth=2
gEnableLogp=1
+
# Enable Automatic Tx Power control
+
gEnableAutomaticTxPowerControl=1
+
+# 0 for OLPC 1 for CLPC and SCPC
+gEnableCloseLoop=1
+
+#Data Inactivity Timeout when in powersave (in ms)
+gDataInactivityTimeout=200
+
+# VHT Tx/Rx MCS values
+# Valid values are 0,1,2. If commented out, the default value is 0.
+# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
+gVhtRxMCS=2
+gVhtTxMCS=2
+
+
END
+
# Note: Configuration parser would not read anything past the END marker
+