qcacmn: Set Coex priorities among WLAN/BT/ZB
Customers need to config the coex priority on some scenarios.
qca_vendor_attr_coex_config_three_way will specifies the
vendor coex config attributes. Host will transfer these
attributs by WMI command.
Change-Id: I6aefcfc3ab13cb982e21ca68701b50731f00ca4d
CRs-Fixed: 2410486
diff --git a/os_if/linux/qca_vendor.h b/os_if/linux/qca_vendor.h
index e4bf57c..dbbef7f 100644
--- a/os_if/linux/qca_vendor.h
+++ b/os_if/linux/qca_vendor.h
@@ -499,6 +499,7 @@
QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169,
QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171,
QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174,
+ QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG = 175,
QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177,
QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH = 178,
QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG = 179,
@@ -6674,6 +6675,149 @@
};
/**
+ * enum qca_coex_config_profiles - This enum defines different types of
+ * traffic streams that can be prioritized one over the other during coex
+ * scenarios.
+ * The types defined in this enum are categorized in the below manner.
+ * 0 - 31 values corresponds to WLAN
+ * 32 - 63 values corresponds to BT
+ * 64 - 95 values corresponds to Zigbee
+ * @QCA_WIFI_STA_DISCOVERY: Prioritize discovery frames for WLAN STA
+ * @QCA_WIFI_STA_CONNECTION: Prioritize connection frames for WLAN STA
+ * @QCA_WIFI_STA_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN STA
+ * @QCA_WIFI_STA_DATA : Prioritize data frames for WLAN STA
+ * @QCA_WIFI_STA_ALL: Priritize all frames for WLAN STA
+ * @QCA_WIFI_SAP_DISCOVERY: Prioritize discovery frames for WLAN SAP
+ * @QCA_WIFI_SAP_CONNECTION: Prioritize connection frames for WLAN SAP
+ * @QCA_WIFI_SAP_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN SAP
+ * @QCA_WIFI_SAP_DATA: Prioritize data frames for WLAN SAP
+ * @QCA_WIFI_SAP_ALL: Prioritize all frames for WLAN SAP
+ * @QCA_BT_A2DP: Prioritize BT A2DP
+ * @QCA_BT_BLE: Prioritize BT BLE
+ * @QCA_BT_SCO: Prioritize BT SCO
+ * @QCA_ZB_LOW: Prioritize Zigbee Low
+ * @QCA_ZB_HIGH: Prioritize Zigbee High
+ */
+enum qca_coex_config_profiles {
+ /* 0 - 31 corresponds to WLAN */
+ QCA_WIFI_STA_DISCOVERY = 0,
+ QCA_WIFI_STA_CONNECTION = 1,
+ QCA_WIFI_STA_CLASS_3_MGMT = 2,
+ QCA_WIFI_STA_DATA = 3,
+ QCA_WIFI_STA_ALL = 4,
+ QCA_WIFI_SAP_DISCOVERY = 5,
+ QCA_WIFI_SAP_CONNECTION = 6,
+ QCA_WIFI_SAP_CLASS_3_MGMT = 7,
+ QCA_WIFI_SAP_DATA = 8,
+ QCA_WIFI_SAP_ALL = 9,
+ QCA_WIFI_CASE_MAX = 31,
+ /* 32 - 63 corresponds to BT */
+ QCA_BT_A2DP = 32,
+ QCA_BT_BLE = 33,
+ QCA_BT_SCO = 34,
+ QCA_BT_CASE_MAX = 63,
+ /* 64 - 95 corresponds to Zigbee */
+ QCA_ZB_LOW = 64,
+ QCA_ZB_HIGH = 65,
+ QCA_ZB_CASE_MAX = 95,
+ /* 0xff is default value if the u8 profile value is not set. */
+ QCA_PROFILE_DEFAULT_VALUE = 255
+};
+
+/**
+ * enum qca_vendor_attr_coex_config_types - Coex configurations types.
+ * This enum defines the valid set of values of coex configuration types. These
+ * values may used by attribute
+ * %QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET: Reset all the
+ * weights to default values.
+ * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START: Start to config
+ * weights with configurability value.
+ */
+enum qca_vendor_attr_coex_config_types {
+ QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET = 1,
+ QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START = 2,
+ QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_TYPE_MAX
+};
+
+/**
+ * enum qca_vendor_attr_coex_config_three_way - Specifies vendor coex config
+ * attributes
+ * Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG
+ *
+ * QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE: u32 attribute.
+ * Indicate config type.
+ * the config types are 32-bit values from qca_vendor_attr_coex_config_types
+ *
+ * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1: u32 attribute.
+ * Indicate the Priority 1 profiles.
+ * the profiles are 8-bit values from enum qca_coex_config_profiles
+ * In same priority level, maximum to 4 profiles can be set here.
+ * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2: u32 attribute.
+ * Indicate the Priority 2 profiles.
+ * the profiles are 8-bit values from enum qca_coex_config_profiles
+ * In same priority level, maximum to 4 profiles can be set here.
+ * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3: u32 attribute.
+ * Indicate the Priority 3 profiles.
+ * the profiles are 8-bit values from enum qca_coex_config_profiles
+ * In same priority level, maximum to 4 profiles can be set here.
+ * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4: u32 attribute.
+ * Indicate the Priority 4 profiles.
+ * the profiles are 8-bit values from enum qca_coex_config_profiles
+ * In same priority level, maximum to 4 profiles can be set here.
+ * NOTE:
+ * limitations for QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_x priority
+ * arrangement:
+ * 1: In the same u32 attribute(priority x), the profiles enum values own
+ * same priority level.
+ * 2: 0xff is default value if the u8 profile value is not set.
+ * 3: max to 4 rules/profiles in same priority level.
+ * 4: max to 4 priority level (priority 1 - priority 4)
+ * 5: one priority level only supports one scenario from WLAN/BT/ZB,
+ * hybrid rules not support.
+ * 6: if WMI_COEX_CONFIG_THREE_WAY_COEX_RESET called, priority x will
+ * remain blank to reset all parameters.
+ * For example:
+ *
+ * If the attributes as follow:
+ * priority 1:
+ * ------------------------------------
+ * | 0xff | 0 | 1 | 2 |
+ * ------------------------------------
+ * priority 2:
+ * -------------------------------------
+ * | 0xff | 0xff | 0xff | 32 |
+ * -------------------------------------
+ * priority 3:
+ * -------------------------------------
+ * | 0xff | 0xff | 0xff | 65 |
+ * -------------------------------------
+ * then it means:
+ * 1: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION
+ * owns same priority level.
+ * 2: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION
+ * has priority over BT_A2DP and ZB_HIGH.
+ * 3: BT_A2DP has priority over ZB_HIGH.
+ */
+
+enum qca_vendor_attr_coex_config_three_way {
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_INVALID = 0,
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE = 1,
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1 = 2,
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2 = 3,
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3 = 4,
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4 = 5,
+
+ /* Keep last */
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST,
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_MAX =
+ QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST - 1,
+};
+
+/**
* enum qca_vendor_attr_peer_stats_cache_type - Represents peer stats cache type
* This enum defines the valid set of values of peer stats cache types. These
* values are used by attribute
@@ -6811,5 +6955,4 @@
QCA_MPTA_HELPER_VENDOR_ATTR_MAX =
QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST - 1
};
-
#endif