| /* |
| * Copyright (c) 2012-2019 The Linux Foundation. All rights reserved. |
| * |
| * Permission to use, copy, modify, and/or distribute this software for |
| * any purpose with or without fee is hereby granted, provided that the |
| * above copyright notice and this permission notice appear in all |
| * copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL |
| * WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED |
| * WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE |
| * AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL |
| * DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR |
| * PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER |
| * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR |
| * PERFORMANCE OF THIS SOFTWARE. |
| */ |
| |
| /** |
| * DOC: declares vendor commands interfacing with linux kernel |
| */ |
| |
| |
| #ifndef _WLAN_QCA_VENDOR_H_ |
| #define _WLAN_QCA_VENDOR_H_ |
| |
| /* Vendor id to be used in vendor specific command and events |
| * to user space. |
| * NOTE: The authoritative place for definition of QCA_NL80211_VENDOR_ID, |
| * vendor subcmd definitions prefixed with QCA_NL80211_VENDOR_SUBCMD, and |
| * qca_wlan_vendor_attr is open source file src/common/qca-vendor.h in |
| * git://w1.fi/srv/git/hostap.git; the values here are just a copy of that |
| */ |
| |
| #define QCA_NL80211_VENDOR_ID 0x001374 |
| |
| /** |
| * enum qca_nl80211_vendor_subcmds: NL 80211 vendor sub command |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Unspecified |
| * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test |
| * Sub commands 2 to 8 are not used |
| * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Roaming |
| * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Avoid frequency. |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: DFS capability |
| * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass |
| * NAN Request/Response and NAN Indication messages. These messages are |
| * interpreted between the framework and the firmware component. While |
| * sending the command from userspace to the driver, payload is not |
| * encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN |
| * is used when receiving vendor events in userspace from the driver. |
| * @QCA_NL80211_VENDOR_SUBCMD_STATS_EXT: Ext stats |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET: Link layer stats set |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET: Link layer stats get |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR: Link layer stats clear |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS: Link layer stats radio |
| * results |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS: Link layer stats interface |
| * results |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS: Link layer stats peer |
| * results |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START: Ext scan start |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP: Ext scan stop |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS: Ext scan get valid |
| * channels |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES: Ext scan get capability |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS: Ext scan get cached |
| * results |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE: Ext scan results |
| * available. Used when report_threshold is reached in scan cache. |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT: Ext scan full scan |
| * result. Used to report scan results when each probe rsp. is received, |
| * if report_events enabled in wifi_scan_cmd_params. |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT: Ext scan event from target. |
| * Indicates progress of scanning state-machine. |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND: Ext scan hotlist |
| * ap found |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST: Ext scan set hotlist |
| * bssid |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST: Ext scan reset |
| * hotlist bssid |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE: Ext scan significant |
| * change |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE: Ext scan set |
| * significant change |
| * ap found |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE: Ext scan reset |
| * significant change |
| * @QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE: Ext tdls enable |
| * @QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE: Ext tdls disable |
| * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS: Ext tdls get status |
| * @QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE: Ext tdls state |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES: Get supported features |
| * @QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI: Set scanning_mac_oui |
| * @QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG: No DFS flag |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX: Get Concurrency Matrix |
| * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Get the key mgmt offload keys |
| * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: After roaming, send the |
| * roaming and auth information. |
| * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_SCHED: Set OCB schedule |
| * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS offload flag |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Get the supported features by the |
| * driver. |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Indicate that driver |
| * started CAC on DFS channel |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Indicate that driver |
| * completed the CAC check on DFS channel |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Indicate that the CAC |
| * check was aborted by the driver |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Indicate that the |
| * driver completed NOP |
| * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Indicate that the |
| * driver detected radar signal on the current operating channel |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO: get wlan driver information |
| * @QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START: start wifi logger |
| * @QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP: memory dump request |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: get logger feature set |
| * @QCA_NL80211_VENDOR_SUBCMD_ROAM: roam |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST: extscan set ssid hotlist |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST: |
| * extscan reset ssid hotlist |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND: hotlist ssid found |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST: hotlist ssid lost |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_LIST: set pno list |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_PASSPOINT_LIST: set passpoint list |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_RESET_PASSPOINT_LIST: |
| * reset passpoint list |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND: pno network found |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND: |
| * passpoint network found |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION: set wifi config |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION: get wifi config |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: get logging features |
| * @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: get link properties |
| * @QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG: set gateway parameters |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST: get preferred channel |
| list |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL: channel hint |
| * @QCA_NL80211_VENDOR_SUBCMD_SETBAND: vendor setband command |
| * @QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN: venodr scan command |
| * @QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE: vendor scan complete |
| * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: vendor abort scan |
| * @QCA_NL80211_VENDOR_SUBCMD_OTA_TEST: enable OTA test |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE: set tx power by percentage |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE_DECR_DB: reduce tx power by DB |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG: SAP configuration |
| * @QCA_NL80211_VENDOR_SUBCMD_TSF: TSF operations command |
| * @QCA_NL80211_VENDOR_SUBCMD_WISA: WISA mode configuration |
| * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to |
| * start the P2P Listen Offload function in device and pass the listen |
| * channel, period, interval, count, number of device types, device |
| * types and vendor information elements to device driver and firmware. |
| * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to |
| * indicate stop request/response of the P2P Listen Offload function in |
| * device. As an event, it indicates either the feature stopped after it |
| * was already running or feature has actually failed to start. |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_STATION: send BSS Information |
| * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After SAP starts |
| * beaconing, this sub command provides the driver, the frequencies on the |
| * 5 GHz to check for any radar activity. Driver selects one channel from |
| * this priority list provided through |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts |
| * to check for radar activity on it. If no radar activity is detected |
| * during the channel availability check period, driver internally switches |
| * to the selected frequency of operation. If the frequency is zero, driver |
| * internally selects a channel. The status of this conditional switch is |
| * indicated through an event using the same sub command through |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are |
| * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Command/event used to config |
| * indication period and threshold for MAC layer counters. |
| * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior |
| * in the host driver. The different TDLS configurations are defined |
| * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration. |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Get HE related capabilities |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS:Set the Specific Absorption Rate |
| * (SAR) power limits. A critical regulation for FCC compliance, OEMs |
| * require methods to set SAR limits on TX power of WLAN/WWAN. |
| * enum qca_vendor_attr_sar_limits attributes are used with this command. |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: Vendor command used to get/set |
| * configuration of vendor ACS. |
| * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the |
| * requisite information leading to a power save failure. The information |
| * carried as part of this event is represented by the |
| * enum qca_attr_chip_power_save_failure attributes. |
| * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics |
| * collection. Uses attributes defined in enum qca_attr_nud_stats_set. |
| * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These |
| * statistics are represented by the enum qca_attr_nud_stats_get |
| * attributes. |
| * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch |
| * the BSS transition status, whether accept or reject, for a list of |
| * candidate BSSIDs provided by the userspace. This uses the vendor |
| * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify |
| * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an |
| * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response |
| * the driver shall specify array of |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a |
| * specific QCA module. The trace levels are represented by |
| * enum qca_attr_trace_level attributes. |
| * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement |
| * Protocol antenna limit in different modes. See enum |
| * qca_wlan_vendor_attr_brp_ant_limit_mode. |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan |
| * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan. |
| * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) |
| * identifying the operation in success case. |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses |
| * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to |
| * be stopped. |
| * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the |
| * specific interface. This can be used to modify some of the low level |
| * scan parameters (off channel dwell time, home channel time) in the |
| * driver/firmware. These parameters are maintained within the host |
| * driver. |
| * This command is valid only when the interface is in the connected |
| * state. |
| * These scan parameters shall be reset by the driver/firmware once |
| * disconnected. The attributes used with this command are defined in |
| * enum qca_wlan_vendor_attr_active_tos. |
| * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the |
| * driver has detected an internal failure. This event carries the |
| * information indicating the reason that triggered this detection. The |
| * attributes for this command are defined in |
| * enum qca_wlan_vendor_attr_hang. |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values |
| * of spectral parameters used. The spectral scan parameters are specified |
| * by enum qca_wlan_vendor_attr_spectral_scan. |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats |
| * for spectral scan functionality. The debug stats are specified by |
| * enum qca_wlan_vendor_attr_spectral_diag_stats. |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral |
| * scan system capabilities. The capabilities are specified |
| * by enum qca_wlan_vendor_attr_spectral_cap. |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current |
| * status of spectral scan. The status values are specified |
| * by enum qca_wlan_vendor_attr_spectral_scan_status. |
| * @QCA_NL80211_VENDOR_SUBCMD_HTT_STATS: Request the firmware |
| * DP stats for a particualr stats type for response evnet |
| * it carries the stats data sent from the FW |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative |
| * RF Operating Parameter (RROP) information. The attributes for this |
| * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is |
| * intended for use by external Auto Channel Selection applications. |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate |
| * (SAR) power limits. This is a companion to the command |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the |
| * settings currently in use. The attributes returned by this command are |
| * defined by enum qca_vendor_attr_sar_limits. |
| * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behaviour of |
| * the WLAN hardware MAC's associated with each WLAN netdev interface. |
| * This works both as a query (user space asks the current mode) or event |
| * interface (driver advertizing the current mode to the user space). |
| * Driver does not trigger this event for temporary hardware mode changes. |
| * Mode changes w.r.t Wi-Fi connection updation ( VIZ creation / deletion, |
| * channel change etc ) are updated with this event. Attributes for this |
| * interface are defined in enum qca_wlan_vendor_attr_mac. |
| * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold |
| * per peer per TID. Attributes for this command are define in |
| * enum qca_wlan_set_qdepth_thresh_attr |
| * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi |
| * test configuration. Attributes for this command are defined in |
| * enum qca_wlan_vendor_attr_wifi_test_config. |
| * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor |
| * command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN, |
| * carried a payload which was a binary blob of data. The command was not |
| * extendable to send more information. The newer version carries the |
| * legacy blob encapsulated within an attribute and can be extended with |
| * additional vendor attributes that can enhance the NAN command |
| * interface. |
| * @QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE: Sub command to get firmware state. |
| * The returned firmware state is specified in the attribute |
| * QCA_WLAN_VENDOR_ATTR_FW_STATE. |
| * |
| */ |
| |
| enum qca_nl80211_vendor_subcmds { |
| QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0, |
| QCA_NL80211_VENDOR_SUBCMD_TEST = 1, |
| QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9, |
| QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11, |
| QCA_NL80211_VENDOR_SUBCMD_NAN = 12, |
| QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13, |
| |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19, |
| |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START = 20, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP = 21, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS = 22, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES = 23, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS = 24, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE = 25, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT = 26, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT = 27, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND = 28, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST = 29, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST = 30, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE = 31, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE = 32, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE = 33, |
| |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36, |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37, |
| |
| QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38, |
| |
| QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39, |
| QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40, |
| |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_LOST = 41, |
| |
| /* Get Concurrency Matrix */ |
| QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42, |
| |
| QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50, |
| QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51, |
| QCA_NL80211_VENDOR_SUBCMD_APFIND = 52, |
| |
| /* Deprecated */ |
| QCA_NL80211_VENDOR_SUBCMD_OCB_SET_SCHED = 53, |
| |
| QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54, |
| |
| QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55, |
| |
| /* Off loaded DFS events */ |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60, |
| |
| QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61, |
| QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62, |
| QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63, |
| QCA_NL80211_VENDOR_SUBCMD_ROAM = 64, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST = 65, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST = 66, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND = 67, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST = 68, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_LIST = 69, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_SET_PASSPOINT_LIST = 70, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_RESET_PASSPOINT_LIST = 71, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND = 72, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND = 73, |
| |
| /* Wi-Fi Configuration subcommands */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74, |
| QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75, |
| QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76, |
| QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77, |
| |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78, |
| QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79, |
| QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80, |
| QCA_NL80211_VENDOR_SUBCMD_NDP = 81, |
| |
| /* NS Offload enable/disable cmd */ |
| QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82, |
| |
| QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83, |
| QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84, |
| |
| QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85, |
| |
| QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91, |
| /* OCB commands */ |
| QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95, |
| QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96, |
| QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97, |
| QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98, |
| QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99, |
| QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100, |
| |
| /* subcommand to get link properties */ |
| QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101, |
| /* LFR Subnet Detection */ |
| QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102, |
| |
| /* DBS subcommands */ |
| QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103, |
| QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104, |
| |
| /* Vendor setband command */ |
| QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105, |
| |
| /* Vendor scan commands */ |
| QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106, |
| QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107, |
| |
| /* OTA test subcommand */ |
| QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108, |
| /* Tx power scaling subcommands */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109, |
| /* Tx power scaling in db subcommands */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE_DECR_DB = 115, |
| QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY = 116, |
| QCA_NL80211_VENDOR_SUBCMD_STA_CONNECT_ROAM_POLICY = 117, |
| QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118, |
| QCA_NL80211_VENDOR_SUBCMD_TSF = 119, |
| QCA_NL80211_VENDOR_SUBCMD_WISA = 120, |
| QCA_NL80211_VENDOR_SUBCMD_GET_STATION = 121, |
| QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122, |
| QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123, |
| QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124, |
| QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125, |
| |
| QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127, |
| /* FTM/indoor location subcommands */ |
| QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132, |
| QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133, |
| QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134, |
| QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135, |
| QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136, |
| |
| /* Encrypt/Decrypt command */ |
| QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137, |
| |
| QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138, |
| /* DMG low level RF sector operations */ |
| QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139, |
| QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140, |
| QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141, |
| QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142, |
| |
| /* Configure the TDLS mode from user space */ |
| QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143, |
| |
| QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144, |
| |
| /* Vendor abort scan command */ |
| QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145, |
| |
| /* Set Specific Absorption Rate(SAR) Power Limits */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146, |
| |
| /* External Auto channel configuration setting */ |
| QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147, |
| |
| QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148, |
| QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149, |
| QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150, |
| QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151, |
| |
| /* Set the trace level for QDF */ |
| QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152, |
| |
| QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153, |
| |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155, |
| QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156, |
| QCA_NL80211_VENDOR_SUBCMD_HANG = 157, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160, |
| QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161, |
| QCA_NL80211_VENDOR_SUBCMD_HTT_STATS = 162, |
| QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163, |
| QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164, |
| QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165, |
| QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166, |
| /* Wi-Fi test configuration subcommand */ |
| QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169, |
| QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171, |
| QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174, |
| QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177, |
| }; |
| |
| enum qca_wlan_vendor_tos { |
| QCA_WLAN_VENDOR_TOS_BK = 0, |
| QCA_WLAN_VENDOR_TOS_BE = 1, |
| QCA_WLAN_VENDOR_TOS_VI = 2, |
| QCA_WLAN_VENDOR_TOS_VO = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS. |
| */ |
| enum qca_wlan_vendor_attr_active_tos { |
| QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0, |
| /* Type Of Service - Represented by qca_wlan_vendor_tos */ |
| QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1, |
| /* Flag attribute representing the start (attribute included) or stop |
| * (attribute not included) of the respective TOS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2, |
| QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_MAX = 3, |
| }; |
| |
| enum qca_wlan_vendor_hang_reason { |
| /* Unspecified reason */ |
| QCA_WLAN_HANG_REASON_UNSPECIFIED = 0, |
| /* No Map for the MAC entry for the received frame */ |
| QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1, |
| /* peer deletion timeout happened */ |
| QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2, |
| /* peer unmap timeout */ |
| QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3, |
| /* Scan request timed out */ |
| QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4, |
| /* Consecutive Scan attempt failures */ |
| QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5, |
| /* Unable to get the message buffer */ |
| QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6, |
| /* Current command processing is timedout */ |
| QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7, |
| /* Timeout for an ACK from FW for suspend request */ |
| QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8, |
| /* Timeout for an ACK from FW for resume request */ |
| QCA_WLAN_HANG_RESUME_TIMEOUT = 9, |
| /* Transmission timeout for consecutive data frames */ |
| QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10, |
| /* Timeout for the TX completion status of data frame */ |
| QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11, |
| /* DXE failure for tx/Rx, DXE resource unavailability */ |
| QCA_WLAN_HANG_DXE_FAILURE = 12, |
| /* WMI pending commands exceed the maximum count */ |
| QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_hang - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_HANG. |
| */ |
| enum qca_wlan_vendor_attr_hang { |
| QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0, |
| /* |
| * Reason for the Hang - Represented by enum |
| * qca_wlan_vendor_hang_reason. |
| */ |
| QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1, |
| |
| QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_HANG_MAX = |
| QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_set_trace_level - Config params for QDF set trace level |
| * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_INVALID: Invalid trace level |
| * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM : Trace level parameters |
| * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MODULE_ID : Module of which trace |
| level needs to be updated. |
| * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_TRACE_MASK : verbose mask, which need |
| * to be set. |
| * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST : after last. |
| * @QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MAX : Max attribute. |
| */ |
| enum qca_vendor_attr_set_trace_level { |
| QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_INVALID = 0, |
| /* |
| * Array of QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM |
| * attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_PARAM = 1, |
| QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MODULE_ID = 2, |
| QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_TRACE_MASK = 3, |
| QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_MAX = |
| QCA_WLAN_VENDOR_ATTR_SET_TRACE_LEVEL_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_station - Sub commands used by |
| * QCA_NL80211_VENDOR_SUBCMD_GET_STATION to get the corresponding |
| * station information. The information obtained through these |
| * commands signify the current info in connected state and |
| * latest cached information during the connected state , if queried |
| * when in disconnected state. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INVALID: Invalid attribute |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO: bss info |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_ASSOC_FAIL_REASON: assoc fail reason |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_REMOTE: remote station info |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST: After last |
| */ |
| enum qca_wlan_vendor_attr_get_station { |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_ASSOC_FAIL_REASON, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_REMOTE, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_MAX = |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_802_11_mode - dot11 mode |
| * @QCA_WLAN_802_11_MODE_11B: mode B |
| * @QCA_WLAN_802_11_MODE_11G: mode G |
| * @QCA_WLAN_802_11_MODE_11N: mode N |
| * @QCA_WLAN_802_11_MODE_11A: mode A |
| * @QCA_WLAN_802_11_MODE_11AC: mode AC |
| * @QCA_WLAN_802_11_MODE_INVALID: Invalid dot11 mode |
| */ |
| enum qca_wlan_802_11_mode { |
| QCA_WLAN_802_11_MODE_11B, |
| QCA_WLAN_802_11_MODE_11G, |
| QCA_WLAN_802_11_MODE_11N, |
| QCA_WLAN_802_11_MODE_11A, |
| QCA_WLAN_802_11_MODE_11AC, |
| QCA_WLAN_802_11_MODE_INVALID, |
| }; |
| |
| /** |
| * enum qca_wlan_auth_type - Authentication key management type |
| * @QCA_WLAN_AUTH_TYPE_INVALID: Invalid key management type |
| * @QCA_WLAN_AUTH_TYPE_OPEN: Open key |
| * @QCA_WLAN_AUTH_TYPE_SHARED: shared key |
| * @QCA_WLAN_AUTH_TYPE_WPA: wpa key |
| * @QCA_WLAN_AUTH_TYPE_WPA_PSK: wpa psk key |
| * @QCA_WLAN_AUTH_TYPE_WPA_NONE: wpa none key |
| * @QCA_WLAN_AUTH_TYPE_RSN: rsn key |
| * @QCA_WLAN_AUTH_TYPE_RSN_PSK: rsn psk key |
| * @QCA_WLAN_AUTH_TYPE_FT: ft key |
| * @QCA_WLAN_AUTH_TYPE_FT_PSK: ft psk key |
| * @QCA_WLAN_AUTH_TYPE_SHA256: shared 256 key |
| * @QCA_WLAN_AUTH_TYPE_SHA256_PSK: shared 256 psk |
| * @QCA_WLAN_AUTH_TYPE_WAI: wai key |
| * @QCA_WLAN_AUTH_TYPE_WAI_PSK wai psk key |
| * @QCA_WLAN_AUTH_TYPE_CCKM_WPA: cckm wpa key |
| * @QCA_WLAN_AUTH_TYPE_CCKM_RSN: cckm rsn key |
| */ |
| enum qca_wlan_auth_type { |
| QCA_WLAN_AUTH_TYPE_INVALID, |
| QCA_WLAN_AUTH_TYPE_OPEN, |
| QCA_WLAN_AUTH_TYPE_SHARED, |
| QCA_WLAN_AUTH_TYPE_WPA, |
| QCA_WLAN_AUTH_TYPE_WPA_PSK, |
| QCA_WLAN_AUTH_TYPE_WPA_NONE, |
| QCA_WLAN_AUTH_TYPE_RSN, |
| QCA_WLAN_AUTH_TYPE_RSN_PSK, |
| QCA_WLAN_AUTH_TYPE_FT, |
| QCA_WLAN_AUTH_TYPE_FT_PSK, |
| QCA_WLAN_AUTH_TYPE_SHA256, |
| QCA_WLAN_AUTH_TYPE_SHA256_PSK, |
| QCA_WLAN_AUTH_TYPE_WAI, |
| QCA_WLAN_AUTH_TYPE_WAI_PSK, |
| QCA_WLAN_AUTH_TYPE_CCKM_WPA, |
| QCA_WLAN_AUTH_TYPE_CCKM_RSN, |
| QCA_WLAN_AUTH_TYPE_AUTOSWITCH, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_station_info - Station Info queried |
| * through QCA_NL80211_VENDOR_SUBCMD_GET_STATION. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_INVALID: Invalid Attribute |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_LINK_STANDARD_NL80211_ATTR: |
| * Get the standard NL attributes Nested with this attribute. |
| * Ex : Query BW , BITRATE32 , NSS , Signal , Noise of the Link - |
| * NL80211_ATTR_SSID / NL80211_ATTR_SURVEY_INFO (Connected Channel) / |
| * NL80211_ATTR_STA_INFO |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_STANDARD_NL80211_ATTR: |
| * Get the standard NL attributes Nested with this attribute. |
| * Ex : Query HT/VHT Capability advertized by the AP. |
| * NL80211_ATTR_VHT_CAPABILITY / NL80211_ATTR_HT_CAPABILITY |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ROAM_COUNT: |
| * Number of successful Roam attempts before a |
| * disconnect, Unsigned 32 bit value |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AKM: |
| * Authentication Key Management Type used for the connected session. |
| * Signified by enum qca_wlan_auth_type |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_802_11_MODE: 802.11 Mode of the |
| * connected Session, signified by enum qca_wlan_802_11_mode |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_HS20_INDICATION: |
| * HS20 Indication Element |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ASSOC_FAIL_REASON: |
| * Status Code Corresponding to the Association Failure. |
| * Unsigned 32 bit value. |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_MAX_PHY_RATE: |
| * Max phy rate of remote station |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_PACKETS: |
| * TX packets to remote station |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_BYTES: |
| * TX bytes to remote station |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_PACKETS: |
| * RX packets from remote station |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_BYTES: |
| * RX bytes from remote station |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_TX_RATE: |
| * Last TX rate with remote station |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_RX_RATE: |
| * Last RX rate with remote station |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_WMM: |
| * Remote station enable/disable WMM |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SUPPORTED_MODE: |
| * Remote station connection mode |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_AMPDU: |
| * Remote station AMPDU enable/disable |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_STBC: |
| * Remote station TX Space-time block coding enable/disable |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_STBC: |
| * Remote station RX Space-time block coding enable/disable |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_CH_WIDTH: |
| * Remote station channel width |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SGI_ENABLE: |
| * Remote station short GI enable/disable |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_PAD: Attribute type for padding |
| * @QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST: After last |
| */ |
| enum qca_wlan_vendor_attr_get_station_info { |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_LINK_STANDARD_NL80211_ATTR, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_STANDARD_NL80211_ATTR, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ROAM_COUNT, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AKM, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_802_11_MODE, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AP_HS20_INDICATION, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_HT_OPERATION, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_VHT_OPERATION, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_ASSOC_FAIL_REASON, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_MAX_PHY_RATE, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_PACKETS, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_BYTES, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_PACKETS, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_BYTES, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_TX_RATE, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_LAST_RX_RATE, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_WMM, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SUPPORTED_MODE, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_AMPDU, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_TX_STBC, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_RX_STBC, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_CH_WIDTH, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_REMOTE_SGI_ENABLE, |
| #if (LINUX_VERSION_CODE >= KERNEL_VERSION(4, 7, 0)) |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_PAD, |
| #endif |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_GET_STATION_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_nl80211_vendor_subcmds_index - vendor sub commands index |
| * |
| * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_INDEX: Avoid frequency |
| * @QCA_NL80211_VENDOR_SUBCMD_NAN_INDEX: Nan |
| * @QCA_NL80211_VENDOR_SUBCMD_STATS_EXT_INDEX: Ext stats |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START_INDEX: Ext scan start |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP_INDEX: Ext scan stop |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES_INDEX: Ext scan get |
| * capability |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS_INDEX: Ext scan get |
| * cached results |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE_INDEX: Ext scan |
| * results available |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT_INDEX: Ext scan full |
| * scan result |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT_INDEX: Ext scan event |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND_INDEX: Ext scan hot list |
| * AP found |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST_INDEX: Ext scan set |
| * bssid hotlist |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST_INDEX: Ext scan reset |
| * bssid hotlist |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE_INDEX: Ext scan |
| * significant change |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE_INDEX: Ext scan |
| * set significant change |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE_INDEX: Ext scan |
| * reset significant change |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET_INDEX: Set stats |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET_INDEX: Get stats |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR_INDEX: Clear stats |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_RADIO_STATS_INDEX: Radio stats |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_IFACE_STATS_INDEX: Iface stats |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_PEER_INFO_STATS_INDEX: Peer info stats |
| * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT_INDEX: MAC layer counters |
| * @QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE_CHANGE_INDEX: Ext tdls state change |
| * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS_INDEX: ACS command |
| * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH_INDEX: Pass Roam and Auth info |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_LOST_INDEX: hotlist ap lost |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND_INDEX: |
| * pno network found index |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND_INDEX: |
| * passpoint match found index |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST_INDEX: |
| * set ssid hotlist index |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST_INDEX: |
| * reset ssid hotlist index |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND_INDEX: |
| * hotlist ssid found index |
| * @QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST_INDEX: |
| * hotlist ssid lost index |
| * @QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT_INDEX |
| * dcc stats event index |
| * @QCA_NL80211_VENDOR_SUBCMD_SCAN_INDEX: vendor scan index |
| * @QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE_INDEX: |
| * vendor scan complete event index |
| * @QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG_INDEX: |
| * update gateway parameters index |
| * @QCA_NL80211_VENDOR_SUBCMD_TSF_INDEX: TSF response events index |
| * @QCA_NL80211_VENDOR_SUBCMD_P2P_LO_EVENT_INDEX: |
| * P2P listen offload index |
| * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH_INDEX: SAP |
| * conditional channel switch index |
| * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET_INDEX: NUD DEBUG Stats index |
| * @QCA_NL80211_VENDOR_SUBCMD_HANG_REASON_INDEX: hang event reason index |
| * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO_INDEX: MAC mode info index |
| * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT_INDEX: NAN Extended index |
| */ |
| |
| enum qca_nl80211_vendor_subcmds_index { |
| QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_INDEX = 0, |
| |
| QCA_NL80211_VENDOR_SUBCMD_NAN_INDEX, |
| |
| #ifdef WLAN_FEATURE_STATS_EXT |
| QCA_NL80211_VENDOR_SUBCMD_STATS_EXT_INDEX, |
| #endif /* WLAN_FEATURE_STATS_EXT */ |
| |
| #ifdef FEATURE_WLAN_EXTSCAN |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_STOP_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CAPABILITIES_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_BSSID_HOTLIST_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_BSSID_HOTLIST_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SIGNIFICANT_CHANGE_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SIGNIFICANT_CHANGE_INDEX, |
| #endif /* FEATURE_WLAN_EXTSCAN */ |
| |
| #ifdef WLAN_FEATURE_LINK_LAYER_STATS |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_LL_RADIO_STATS_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_LL_IFACE_STATS_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_LL_PEER_INFO_STATS_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT_INDEX, |
| #endif /* WLAN_FEATURE_LINK_LAYER_STATS */ |
| |
| QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE_CHANGE_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_DO_ACS_INDEX, |
| #ifdef WLAN_FEATURE_ROAM_OFFLOAD |
| QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH_INDEX, |
| #endif |
| /* DFS */ |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED_INDEX, |
| #ifdef FEATURE_WLAN_EXTSCAN |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_LOST_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_NETWORK_FOUND_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_PNO_PASSPOINT_NETWORK_FOUND_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_RESET_SSID_HOTLIST_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_FOUND_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_SSID_LOST_INDEX, |
| #endif /* FEATURE_WLAN_EXTSCAN */ |
| QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI_INDEX, |
| #ifdef WLAN_FEATURE_MEMDUMP |
| QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP_INDEX, |
| #endif /* WLAN_FEATURE_MEMDUMP */ |
| /* OCB events */ |
| QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_SCAN_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG_INDEX, |
| #ifdef WLAN_FEATURE_TSF |
| QCA_NL80211_VENDOR_SUBCMD_TSF_INDEX, |
| #endif |
| QCA_NL80211_VENDOR_SUBCMD_NDP_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_P2P_LO_EVENT_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_UPDATE_EXTERNAL_ACS_CONFIG, |
| QCA_NL80211_VENDOR_SUBCMD_PWR_SAVE_FAIL_DETECTED_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_HANG_REASON_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_HTT_STATS_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_NAN_EXT_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT_INDEX, |
| QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES_INDEX, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_tdls_enable - TDLS enable attribute |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR: An array of 6 x Unsigned 8-bit |
| * value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_CHANNEL: Signed 32-bit value, but lets |
| * keep as unsigned for now |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_GLOBAL_OPERATING_CLASS: operating class |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX_LATENCY_MS: Enable max latency in ms |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MIN_BANDWIDTH_KBPS: Enable min bandwidth |
| * in KBPS |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_tdls_enable { |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_GLOBAL_OPERATING_CLASS, |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX_LATENCY_MS, |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MIN_BANDWIDTH_KBPS, |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_ENABLE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_tdls_disable: tdls disable attribute |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAC_ADDR: An array of 6 x Unsigned |
| * 8-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_tdls_disable { |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_DISABLE_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_chip_power_save_failure_reason: Power save failure reason |
| * @QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL: Indicates power save failure |
| * due to protocol/module. |
| * @QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE: power save failure |
| * due to hardware |
| */ |
| enum qca_chip_power_save_failure_reason { |
| QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0, |
| QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1, |
| }; |
| |
| /** |
| * qca_attr_chip_power_save_failure: attributes to vendor subcmd |
| * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carry the requisite |
| * information leading to the power save failure. |
| * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID : invalid |
| * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON : power save failure reason |
| * represented by enum qca_chip_power_save_failure_reason |
| * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST : Last |
| * @QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX : Max value |
| */ |
| enum qca_attr_chip_power_save_failure { |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0, |
| |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1, |
| |
| /* keep last */ |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST, |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX = |
| QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1, |
| }; |
| |
| |
| /** |
| * enum qca_wlan_vendor_attr_tdls_get_status - tdls get status attribute |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR: An array of 6 x Unsigned |
| * 8-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_STATE: get status state, |
| * unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_REASON: get status reason |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_CHANNEL: get status channel, |
| * unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_GLOBAL_OPERATING_CLASS: get operating |
| * class, unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_tdls_get_status { |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_STATE, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_REASON, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_GLOBAL_OPERATING_CLASS, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_STATUS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_tdls_state - tdls state attribute |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_INVALID: Initial invalid value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAC_ADDR: An array of 6 x Unsigned |
| * 8-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_NEW_STATE: TDLS new state, |
| * unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_REASON: TDLS state reason |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_CHANNEL: TDLS state channel, |
| * unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_GLOBAL_OPERATING_CLASS: TDLS state |
| * operating class, unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_tdls_state { |
| QCA_WLAN_VENDOR_ATTR_TDLS_STATE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_TDLS_NEW_STATE, |
| QCA_WLAN_VENDOR_ATTR_TDLS_STATE_REASON, |
| QCA_WLAN_VENDOR_ATTR_TDLS_STATE_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_TDLS_STATE_GLOBAL_OPERATING_CLASS, |
| QCA_WLAN_VENDOR_ATTR_TDLS_STATE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_STATE_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_STATE_AFTER_LAST - 1, |
| }; |
| |
| /* enum's to provide TDLS capabilities */ |
| enum qca_wlan_vendor_attr_get_tdls_capabilities { |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS = 1, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1, |
| }; |
| |
| enum qca_wlan_vendor_attr { |
| QCA_WLAN_VENDOR_ATTR_INVALID = 0, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */ |
| QCA_WLAN_VENDOR_ATTR_DFS = 1, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_NAN */ |
| QCA_WLAN_VENDOR_ATTR_NAN = 2, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ |
| QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ |
| QCA_WLAN_VENDOR_ATTR_IFINDEX = 4, |
| /* |
| * used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined |
| * by enum qca_roaming_policy. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5, |
| QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6, |
| /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ |
| QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7, |
| QCA_WLAN_VENDOR_ATTR_TEST = 8, |
| /* |
| * used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES |
| * Unsigned 32-bit value. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11, |
| /* Unsigned 32-bit value from enum qca_set_band. */ |
| QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12, |
| /* Dummy (NOP) attribute for 64 bit padding */ |
| QCA_WLAN_VENDOR_ATTR_PAD = 13, |
| /* |
| * Unique FTM session cookie (Unsigned 64 bit). Specified in |
| * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in |
| * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and |
| * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14, |
| /* |
| * Indoor location capabilities, returned by |
| * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA. |
| * see enum qca_wlan_vendor_attr_loc_capa. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15, |
| /* |
| * Array of nested attributes containing information about each peer |
| * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info |
| * for supported attributes for each peer. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16, |
| /* |
| * Array of nested attributes containing measurement results for |
| * one or more peers, reported by the |
| * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event. |
| * See enum qca_wlan_vendor_attr_peer_result for list of supported |
| * attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17, |
| /* Flag attribute for enabling or disabling responder functionality. */ |
| QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18, |
| /* |
| * Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER |
| * command to specify the LCI report that will be sent by |
| * the responder during a measurement exchange. The format is |
| * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19, |
| /* |
| * Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER |
| * command to specify the location civic report that will |
| * be sent by the responder during a measurement exchange. |
| * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20, |
| /* |
| * Session/measurement completion status code, |
| * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and |
| * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT |
| * see enum qca_vendor_attr_loc_session_status. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21, |
| /* |
| * Initial dialog token used by responder (0 if not specified), |
| * unsigned 8 bit value. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22, |
| /* |
| * AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS |
| * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if |
| * AOA measurements are needed as part of an FTM session. |
| * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See |
| * enum qca_wlan_vendor_attr_aoa_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23, |
| /* |
| * A bit mask (unsigned 32 bit value) of antenna arrays used |
| * by indoor location measurements. Refers to the antenna |
| * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24, |
| /* |
| * AOA measurement data. Its contents depends on the AOA measurement |
| * type and antenna array mask: |
| * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values, |
| * phase of the strongest CIR path for each antenna in the measured |
| * array(s). |
| * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16 |
| * values, phase and amplitude of the strongest CIR path for each |
| * antenna in the measured array(s). |
| */ |
| QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command |
| * to specify the chain number (unsigned 32 bit value) to inquire |
| * the corresponding antenna RSSI value */ |
| QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command |
| * to report the specific antenna RSSI value (unsigned 32 bit value) */ |
| QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27, |
| /* Frequency in MHz, various uses. Unsigned 32 bit value */ |
| QCA_WLAN_VENDOR_ATTR_FREQ = 28, |
| /* |
| * TSF timer value, unsigned 64 bit value. |
| * May be returned by various commands. |
| */ |
| QCA_WLAN_VENDOR_ATTR_TSF = 29, |
| /* |
| * DMG RF sector index, unsigned 16 bit number. Valid values are |
| * 0..127 for sector indices or 65535 as special value used to |
| * unlock sector selection in |
| * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR. |
| */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30, |
| /* |
| * DMG RF sector type, unsigned 8 bit value. One of the values |
| * in enum qca_wlan_vendor_attr_dmg_rf_sector_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31, |
| /* |
| * Bitmask of DMG RF modules for which information is requested. Each |
| * bit corresponds to an RF module with the same index as the bit |
| * number. Unsigned 32 bit number but only low 8 bits can be set since |
| * all DMG chips currently have up to 8 RF modules. |
| */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32, |
| /* |
| * Array of nested attributes where each entry is DMG RF sector |
| * configuration for a single RF module. |
| * Attributes for each entry are taken from enum |
| * qca_wlan_vendor_attr_dmg_rf_sector_cfg. |
| * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG |
| * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG. |
| */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command |
| * to report frame aggregation statistics to userspace. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34, |
| QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35, |
| /* |
| * Unsigned 8-bit value representing MBO transition reason code as |
| * provided by the AP used by subcommand |
| * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is |
| * specified by the userspace in the request to the driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36, |
| /* |
| * Array of nested attributes, BSSID and status code, used by subcommand |
| * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each |
| * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info. |
| * The userspace space specifies the list/array of candidate BSSIDs in |
| * the order of preference in the request. The driver specifies the |
| * status code, for each BSSID in the list, in the response. The |
| * acceptable candidates are listed in the order preferred by the |
| * driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command |
| * See enum qca_wlan_vendor_attr_brp_ant_limit_mode. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command |
| * to define the number of antennas to use for BRP. |
| * different purpose in each ANT_LIMIT_MODE: |
| * DISABLE - ignored |
| * EFFECTIVE - upper limit to number of antennas to be used |
| * FORCE - exact number of antennas to be used |
| * unsigned 8 bit value |
| */ |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command |
| * to report the corresponding antenna index to the chain RSSI value |
| */ |
| QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command |
| * to report the specific antenna EVM value (unsigned 32 bit value). |
| * With a determinate group of antennas, the driver specifies the |
| * EVM value for each antenna ID, and application extract them |
| * in user space. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CHAIN_EVM = 41, |
| /* |
| * Used in QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE command to report |
| * wlan firmware current state. FW state is an unsigned 8 bit value, |
| * one of the values in enum qca_wlan_vendor_attr_fw_state. |
| */ |
| QCA_WLAN_VENDOR_ATTR_FW_STATE = 42, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1 |
| }; |
| |
| #ifdef FEATURE_WLAN_EXTSCAN |
| enum qca_wlan_vendor_attr_extscan_config_params { |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0, |
| |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1, |
| |
| /* |
| * Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_VALID_CHANNELS sub command. |
| */ |
| |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND |
| = 2, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS |
| = 3, |
| |
| /* |
| * Attributes for input params used by |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_START sub command. |
| */ |
| |
| /* Unsigned 32-bit value; channel frequency */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_CHANNEL = 4, |
| /* Unsigned 32-bit value; dwell time in ms. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_DWELL_TIME = 5, |
| /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_PASSIVE = 6, |
| /* Unsigned 8-bit value; channel class */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_CLASS = 7, |
| |
| /* Unsigned 8-bit value; bucket index, 0 based */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_INDEX = 8, |
| /* Unsigned 8-bit value; band. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_BAND = 9, |
| /* Unsigned 32-bit value; desired period, in ms. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_PERIOD = 10, |
| /* Unsigned 8-bit value; report events semantics. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_REPORT_EVENTS = 11, |
| /* |
| * Unsigned 32-bit value. Followed by a nested array of |
| * EXTSCAN_CHANNEL_SPEC_* attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12, |
| |
| /* |
| * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC_* attributes. |
| * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CHANNEL_SPEC = 13, |
| |
| /* Unsigned 32-bit value; base timer period in ms. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14, |
| /* |
| * Unsigned 32-bit value; number of APs to store in each scan in the |
| * BSSID/RSSI history buffer (keep the highest RSSI APs). |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15, |
| /* |
| * Unsigned 8-bit value; in %, when scan buffer is this much full, wake |
| * up AP. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT |
| = 16, |
| |
| /* |
| * Unsigned 8-bit value; number of scan bucket specs; followed by a |
| * nested array of_EXTSCAN_BUCKET_SPEC_* attributes and values. The size |
| * of the array is determined by NUM_BUCKETS. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17, |
| |
| /* |
| * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_* attributes. |
| * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC = 18, |
| |
| /* Unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH |
| = 19, |
| /* Unsigned 32-bit value; maximum number of results to be returned. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX |
| = 20, |
| |
| /* An array of 6 x unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_BSSID = 21, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24, |
| |
| /* |
| * Number of hotlist APs as unsigned 32-bit value, followed by a nested |
| * array of AP_THRESHOLD_PARAM attributes and values. The size of the |
| * array is determined by NUM_AP. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25, |
| |
| /* |
| * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM_* attributes. |
| * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_AP_THRESHOLD_PARAM = 26, |
| |
| /* Unsigned 32-bit value; number of samples for averaging RSSI. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE |
| = 27, |
| /* Unsigned 32-bit value; number of samples to confirm AP loss. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE |
| = 28, |
| /* Unsigned 32-bit value; number of APs breaching threshold. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29, |
| /* |
| * Unsigned 32-bit value; number of APs. Followed by an array of |
| * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30, |
| /* Unsigned 32-bit value; number of samples to confirm AP loss. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE |
| = 31, |
| /* |
| * Unsigned 32-bit value. If max_period is non zero or different than |
| * period, then this bucket is an exponential backoff bucket. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_MAX_PERIOD = 32, |
| /* Unsigned 32-bit value. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_BASE = 33, |
| /* |
| * Unsigned 32-bit value. For exponential back off bucket, number of |
| * scans to perform for a given period. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_BUCKET_SPEC_STEP_COUNT = 34, |
| /* |
| * Unsigned 8-bit value; in number of scans, wake up AP after these |
| * many scans. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS |
| = 35, |
| |
| /* |
| * Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SET_SSID_HOTLIST sub command. |
| */ |
| |
| /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE |
| = 36, |
| /* |
| * Number of hotlist SSIDs as unsigned 32-bit value, followed by a |
| * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The |
| * size of the array is determined by NUM_SSID. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37, |
| /* |
| * Array of QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_* |
| * attributes. |
| * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_HOTLIST_PARAMS_NUM_SSID |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM = 38, |
| |
| /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_SSID = 39, |
| /* Unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_BAND = 40, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42, |
| /* Unsigned 32-bit value; a bitmask with additional extscan config flag. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CONFIGURATION_FLAGS = 43, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1, |
| }; |
| |
| enum qca_wlan_vendor_attr_extscan_results { |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_INVALID = 0, |
| |
| /* |
| * Unsigned 32-bit value; must match the request Id supplied by |
| * Wi-Fi HAL in the corresponding subcmd NL msg. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_REQUEST_ID = 1, |
| |
| /* |
| * Unsigned 32-bit value; used to indicate the status response from |
| * firmware/driver for the vendor sub-command. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_STATUS = 2, |
| |
| /* |
| * EXTSCAN Valid Channels attributes */ |
| /* Unsigned 32bit value; followed by a nested array of CHANNELS. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_CHANNELS = 3, |
| /* |
| * An array of NUM_CHANNELS x unsigned 32-bit value integers |
| * representing channel numbers. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CHANNELS = 4, |
| |
| /* EXTSCAN Capabilities attributes */ |
| |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN |
| = 7, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE |
| = 8, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD |
| = 9, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS |
| = 11, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES |
| = 12, |
| |
| /* |
| * EXTSCAN Attributes used with |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_RESULTS_AVAILABLE sub-command. |
| */ |
| |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13, |
| |
| /* |
| * EXTSCAN attributes used with |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_FULL_SCAN_RESULT sub-command. |
| */ |
| |
| /* |
| * An array of NUM_RESULTS_AVAILABLE x |
| * QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_* |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST = 14, |
| |
| /* Unsigned 64-bit value; age of sample at the time of retrieval */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15, |
| /* 33 x unsigned 8-bit value; NULL terminated SSID */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_SSID = 16, |
| /* An array of 6 x unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_BSSID = 17, |
| /* Unsigned 32-bit value; channel frequency in MHz */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18, |
| /* Signed 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RSSI = 19, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RTT = 20, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21, |
| /* Unsigned 16-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22, |
| /* Unsigned 16-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23, |
| /* Unsigned 32-bit value; size of the IE DATA blob */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24, |
| /* |
| * An array of IE_LENGTH x unsigned 8-bit value; blob of all the |
| * information elements found in the beacon; this data should be a |
| * packed list of wifi_information_element objects, one after the |
| * other. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25, |
| |
| /* |
| * Unsigned 8-bit value; set by driver to indicate more scan results are |
| * available. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26, |
| |
| /* |
| * EXTSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SCAN_EVENT sub-command. |
| */ |
| /* Unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_EVENT_TYPE = 27, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SCAN_EVENT_STATUS = 28, |
| |
| /* |
| * EXTSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_HOTLIST_AP_FOUND sub-command. |
| */ |
| /* |
| * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE |
| * to indicate number of results. |
| * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the |
| * list of results. |
| */ |
| |
| /* |
| * EXTSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_SIGNIFICANT_CHANGE sub-command. |
| */ |
| /* An array of 6 x unsigned 8-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29, |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL |
| = 30, |
| /* Unsigned 32-bit value. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI |
| = 31, |
| /* |
| * A nested array of signed 32-bit RSSI values. Size of the array is |
| * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST |
| = 32, |
| |
| /* |
| * EXTSCAN attributes used with |
| * QCA_NL80211_VENDOR_SUBCMD_EXTSCAN_GET_CACHED_RESULTS sub-command. |
| */ |
| /* |
| * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE |
| * to indicate number of extscan cached results returned. |
| * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_LIST to indicate |
| * the list of extscan cached results. |
| */ |
| |
| /* |
| * An array of NUM_RESULTS_AVAILABLE x |
| * QCA_NL80211_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_* |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_LIST = 33, |
| /* Unsigned 32-bit value; a unique identifier for the scan unit. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_SCAN_ID = 34, |
| /* |
| * Unsigned 32-bit value; a bitmask w/additional information about scan. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_CACHED_RESULTS_FLAGS = 35, |
| /* |
| * Use attr QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE |
| * to indicate number of wifi scan results/bssids retrieved by the scan. |
| * Also, use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the |
| * list of wifi scan results returned for each cached result block. |
| */ |
| |
| /* |
| * EXTSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command. |
| */ |
| /* |
| * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE for |
| * number of results. |
| * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the nested |
| * list of wifi scan results returned for each |
| * wifi_passpoint_match_result block. |
| * Array size: QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_NUM_RESULTS_AVAILABLE. |
| */ |
| |
| /* |
| * EXTSCAN attributes for |
| * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command. |
| */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES |
| = 36, |
| /* |
| * A nested array of |
| * QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_* |
| * attributes. Array size = |
| * *_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37, |
| |
| /* Unsigned 32-bit value; network block id for the matched network */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38, |
| /* |
| * Use QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_LIST to indicate the nested |
| * list of wifi scan results returned for each |
| * wifi_passpoint_match_result block. |
| */ |
| /* Unsigned 32-bit value */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39, |
| /* |
| * An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values; |
| * ANQP data in the information_element format. |
| */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40, |
| |
| /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41, |
| /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42, |
| /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID |
| = 43, |
| /* Unsigned 32-bit value; a EXTSCAN Capabilities attribute. */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID |
| = 44, |
| |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_BUCKETS_SCANNED = 45, |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_MAX_NUM_BLACKLISTED_BSSID = 46, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_MAX = |
| QCA_WLAN_VENDOR_ATTR_EXTSCAN_RESULTS_AFTER_LAST - 1, |
| }; |
| #endif |
| |
| #ifdef WLAN_FEATURE_LINK_LAYER_STATS |
| |
| /** |
| * enum qca_wlan_vendor_attr_ll_stats_set - vendor attribute set stats |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD: Size threshold |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING: |
| * Aggresive stats gathering |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_ll_stats_set { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ll_stats_get - vendor attribute get stats |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID: Unsigned 32bit value |
| * provided by the caller issuing the GET stats command. When reporting |
| * the stats results, the driver uses the same value to indicate which |
| * GET request the results correspond to. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK: Get config request mask |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK: Config response mask |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP: Config stop response |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_ll_stats_get { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ll_stats_clr - vendor attribute clear stats |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK: Config request mask |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ: Config stop mask |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK: Config response mask |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP: Config stop response |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_ll_stats_clr { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ll_stats_results_type - ll stats result type |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_INVALID: Initial invalid value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_RADIO: Link layer stats type radio |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_IFACE: Link layer stats type interface |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_PEER: Link layer stats type peer |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_AFTER_LAST: Last value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_ll_stats_results_type { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_RADIO = 1, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_IFACE, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_PEER, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ll_stats_results - vendor attribute stats results |
| * |
| * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are nested |
| * within the interface stats. |
| * |
| * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could be nested |
| * within the interface stats. |
| * |
| * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are nested |
| * within the interface stats. |
| * |
| * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* could be nested |
| * within the peer info stats. |
| * |
| * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could be |
| * nested within the channel stats. |
| * |
| * Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ could be nested |
| * within the radio stats. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE: Interface mode, e.g., STA, |
| * SOFTAP, IBSS, etc. Type = enum wifi_interface_mode |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR: Interface MAC address. |
| * An array of 6 Unsigned int8_t |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE: |
| * Type = enum wifi_connection_state, e.g., DISCONNECTED, AUTHENTICATING, |
| * etc. Valid for STA, CLI only |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING: |
| * Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE |
| * (is that valid for STA only?) |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES: Unsigned 32bit value. |
| * WIFI_CAPABILITY_XXX |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID: NULL terminated SSID. An |
| * array of 33 Unsigned 8bit values |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID: BSSID. An array of 6 |
| * Unsigned 8bit values |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR: Country string |
| * advertised by AP. An array of 3 Unsigned 8bit values |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR: Country string for |
| * this association. An array of 3 Unsigned 8bit values |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC: Type = enum wifi_traffic_ac e.g. |
| * V0, VI, BE and BK |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT: Unsigned int 32 value |
| * corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN: Unsigned int 32 |
| * value corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX: Unsigned int 32 |
| * value corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG: Unsigned int 32 |
| * value corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES: Unsigned int 32 |
| * value corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS: Unsigned int 32 |
| * value corresponding to respective AC |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE: Type = enum wifi_peer_type |
| * Peer type, e.g., STA, AP, P2P GO etc |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS: MAC addr corresponding |
| * to respective peer. An array of 6 Unsigned 8bit values |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES: Unsigned int 32bit |
| * value representing capabilities corresponding to respective peer. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES: Unsigned 32bit value. |
| * Number of rates |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE: Unsigned int 8bit value: |
| * 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS: Unsigned int 8bit value: |
| * 0:1x1, 1:2x2, 3:3x3, 4:4x4 |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW: Unsigned int 8bit value: |
| * 0:20MHz, 1:40Mhz, 2:80Mhz, 3:160Mhz |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX: Unsigned int 8bit value: |
| * OFDM/CCK rate code would be as per IEEE Std in the units of 0.5mbps |
| * HT/VHT it would be mcs index |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE: Unsigned 32bit value. |
| * Bit rate in units of 100Kbps |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU: Unsigned int 32bit value. |
| * Number of successfully transmitted data pkts i.e., with ACK received |
| * corresponding to the respective rate |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU: Unsigned int 32bit value. |
| * Number of received data pkts corresponding to the respective rate |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST: Unsigned int 32bit value. |
| * Number of data pkts losses, i.e., no ACK received corresponding to |
| * the respective rate |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES: Unsigned int 32bit value. |
| * Total number of data pkt retries for the respective rate |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT: Unsigned int 32bit value. |
| * Total number of short data pkt retries for the respective rate |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG: Unsigned int 32bit value. |
| * Total number of long data pkt retries for the respective rate |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID: Radio id |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME: Unsigned 32bit value. |
| * Total number of msecs the radio is awake accruing over time |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME: Unsigned 32bit value. |
| * Total number of msecs the radio is transmitting accruing over time |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME: Unsigned 32bit value. |
| * Total number of msecs the radio is in active receive accruing over time |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN: Unsigned 32bit value. |
| * Total number of msecs the radio is awake due to all scan accruing |
| * over time |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD: Unsigned 32bit value. |
| * Total number of msecs the radio is awake due to NAN accruing over time. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN: Unsigned 32bit value. |
| * Total number of msecs the radio is awake due to GSCAN accruing over time |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN: Unsigned 32bit value. |
| * Total number of msecs the radio is awake due to roam scan accruing over |
| * time. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN: Unsigned 32bit value. |
| * Total number of msecs the radio is awake due to PNO scan accruing over |
| * time. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20: Unsigned 32bit value. |
| * Total number of msecs the radio is awake due to HS2.0 scans and GAS |
| * exchange accruing over time. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS: Unsigned 32bit value. |
| * Number of channels |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH: |
| * Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80, etc. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ: |
| * Unsigned 32bit value. Primary 20MHz channel. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0: |
| * Unsigned 32bit value. Center frequency (MHz) first segment. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1: |
| * Unsigned 32bit value. Center frequency (MHz) second segment. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME: Unsigned int 32bit value |
| * representing total number of msecs the radio is awake on that channel |
| * accruing over time, corresponding to the respective channel. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME: Unsigned int 32bit |
| * value representing total number of msecs the CCA register is busy |
| * accruing over time corresponding to the respective channel. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS: Number of radios |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO: Channel info |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO: Peer info |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO: Peer rate info |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO: WMM info |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA: Unsigned 8bit value. |
| * Used by the driver; if set to 1, it indicates that more stats, e.g., |
| * peers or radio, are to follow in the next |
| * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event. Otherwise, it |
| * is set to 0. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET: tsf offset |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED: leaky ap detected |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED: |
| * average number of frames leaked |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME: guard time |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE: Link Layer stats type |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS: LL Radio Number of |
| * Tx Levels |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL:Number of msecs the |
| * radio spent in transmitting for each power level |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT: RTS successful count |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT: RTS fail count |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT: PPDU successful count |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT: PPDU fail count |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_MAX: Max value |
| */ |
| |
| enum qca_wlan_vendor_attr_ll_stats_results { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1 |
| }; |
| |
| enum qca_wlan_vendor_attr_ll_stats_type { |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3, |
| |
| /* keep last */ |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST, |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX = |
| QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1, |
| }; |
| |
| #endif /* WLAN_FEATURE_LINK_LAYER_STATS */ |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_supported_features - get supported feature |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET: Unsigned 32bit value |
| * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_FEATURE_SET_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_get_supported_features { |
| QCA_WLAN_VENDOR_ATTR_FEATURE_SET_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_FEATURE_SET = 1, |
| QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FEATURE_SET_MAX = |
| QCA_WLAN_VENDOR_ATTR_FEATURE_SET_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_set_scanning_mac_oui - set scanning mac oui |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI: An array of 3 x Unsigned 8-bit |
| * value |
| * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_set_scanning_mac_oui { |
| QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI = 1, |
| QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_MAX = |
| QCA_WLAN_VENDOR_ATTR_SET_SCANNING_MAC_OUI_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes |
| * with frequencies to be scanned (in MHz) |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported |
| * rates to be included |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests |
| * at non CCK rate in 2GHz band |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the |
| * driver for the specific scan request |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan |
| * request decoded as in enum scan_status |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation |
| * scan flag is set |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with |
| * randomisation |
| * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: BSSID provided to do scan for specific BSS |
| */ |
| enum qca_wlan_vendor_attr_scan { |
| QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0, |
| QCA_WLAN_VENDOR_ATTR_SCAN_IE, |
| QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES, |
| QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS, |
| QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES, |
| QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE, |
| QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS, |
| QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE, |
| QCA_WLAN_VENDOR_ATTR_SCAN_STATUS, |
| QCA_WLAN_VENDOR_ATTR_SCAN_MAC, |
| QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK, |
| QCA_WLAN_VENDOR_ATTR_SCAN_BSSID, |
| QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SCAN_MAX = |
| QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum scan_status - Specifies the valid values the vendor scan attribute |
| * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take |
| * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with |
| * new scan results |
| * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between |
| */ |
| enum scan_status { |
| VENDOR_SCAN_STATUS_NEW_RESULTS, |
| VENDOR_SCAN_STATUS_ABORTED, |
| VENDOR_SCAN_STATUS_MAX, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_concurrency_matrix - get concurrency matrix |
| * |
| * NL attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX sub command. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_CONFIG_PARAM_SET_SIZE_MAX: |
| * Unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET_SIZE: |
| * Unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET: Set results. An |
| * array of SET_SIZE x Unsigned 32bit values representing concurrency |
| * combinations |
| * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_get_concurrency_matrix { |
| QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_CONFIG_PARAM_SET_SIZE_MAX |
| = 1, |
| QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET_SIZE = 2, |
| QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_RESULTS_SET = 3, |
| QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_MAX = |
| QCA_WLAN_VENDOR_ATTR_GET_CONCURRENCY_MATRIX_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_set_no_dfs_flag - vendor attribute set no dfs flag |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG: Unsigned 32-bit value |
| * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_set_no_dfs_flag { |
| QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG = 1, |
| QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SET_NO_DFS_FLAG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_wisa_cmd |
| * @QCA_WLAN_VENDOR_ATTR_WISA_INVALID: Invalid attr |
| * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value attr (u32) |
| * @QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_WISA_MAX: Max Value |
| * WISA setup vendor commands |
| */ |
| enum qca_vendor_attr_wisa_cmd { |
| QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_WISA_MODE, |
| QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WISA_MAX = |
| QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1 |
| }; |
| |
| enum qca_roaming_policy { |
| QCA_ROAMING_NOT_ALLOWED, |
| QCA_ROAMING_ALLOWED_WITHIN_ESS, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_auth - vendor event for roaming |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID: BSSID of the roamed AP |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE: Request IE |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE: Response IE |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED: Authorization Status |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR: Replay Counter |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK: KCK of the PTK |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK: KEK of the PTK |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS: subnet change status |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS: |
| * Indicates the status of re-association requested by user space for |
| * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID. |
| * Type u16. |
| * Represents the status code from AP. Use |
| * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the |
| * real status code for failures. |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION: |
| * This attribute indicates that the old association was maintained when |
| * a re-association is requested by user space and that re-association |
| * attempt fails (i.e., cannot connect to the requested BSS, but can |
| * remain associated with the BSS with which the association was in |
| * place when being requested to roam). Used along with |
| * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current |
| * re-association status. Type flag. |
| * This attribute is applicable only for re-association failure cases. |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK: AUTH PMK |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID: AUTH PMKID |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM: FILS erp next |
| * seq number |
| */ |
| enum qca_wlan_vendor_attr_roam_auth { |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_wifi_config - wifi config |
| * |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_DYNAMIC_DTIM: dynamic DTIM |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_STATS_AVG_FACTOR: avg factor |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_GUARD_TIME: guard time |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_MAX: max value |
| */ |
| enum qca_wlan_vendor_attr_wifi_config { |
| QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_DYNAMIC_DTIM = 1, |
| QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_STATS_AVG_FACTOR = 2, |
| QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_GUARD_TIME = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_WIFI_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_epno_type - the type of request to the EPNO command |
| * @QCA_WLAN_EPNO: epno type request |
| * @QCA_WLAN_PNO: pno type request |
| */ |
| enum qca_wlan_epno_type { |
| QCA_WLAN_EPNO, |
| QCA_WLAN_PNO |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_pno_config_params - pno config params |
| * |
| * @QCA_WLAN_VENDOR_ATTR_PNO_INVALID - Invalid initial value |
| * |
| * NL attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command. |
| * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM: |
| * Unsigned 32-bit value; pno passpoint number of networks |
| * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY: |
| * Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_* |
| * attributes. Array size = |
| * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM. |
| * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID: |
| * Unsigned 32-bit value; network id |
| * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM: |
| * An array of 256 x Unsigned 8-bit value; NULL terminated UTF8 encoded |
| * realm, 0 if unspecified. |
| * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID: |
| * An array of 16 x Unsigned 32-bit value; roaming consortium ids |
| * to match, 0 if unspecified. |
| * @QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN: |
| * An array of 6 x Unsigned 8-bit value; mcc/mnc combination, 0s if |
| * unspecified. |
| * |
| * NL attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command. |
| * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS: |
| * Unsigned 32-bit value; set pno number of networks |
| * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST: |
| * Array of nested |
| * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_* |
| * attributes. Array size = |
| * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS |
| * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID: |
| * An array of 33 x Unsigned 8-bit value; NULL terminated SSID |
| * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD: |
| * Signed 8-bit value; threshold for considering this SSID as found, |
| * required granularity for this threshold is 4dBm to 8dBm |
| * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS: |
| * Unsigned 8-bit value; WIFI_PNO_FLAG_XXX |
| * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT: |
| * Unsigned 8-bit value; auth bit field for matching WPA IE |
| * @QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE |
| * Unsigned 8-bit to indicate ePNO type; values from qca_wlan_epno_type |
| *@QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST |
| * Nested attribute to send the channel list |
| *@QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL |
| * Unsigned 32-bit value; indicates the Interval between PNO scan |
| * cycles in msec |
| *@QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI |
| * Signed 32-bit value; minimum 5GHz RSSI for a BSSID to be considered |
| *@QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI |
| * Signed 32-bit value; minimum 2.4GHz RSSI for a BSSID to be considered |
| * This attribute is obsolete now. |
| *@QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX |
| * Signed 32-bit value; the maximum score that a network |
| * can have before bonuses |
| *@QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS |
| * Signed 32-bit value; only report when there is a network's |
| * score this much higher han the current connection |
| *@QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS |
| * Signed 32-bit value; score bonus for all networks with |
| * the same network flag |
| *@QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS |
| * Signed 32-bit value; score bonus for networks that are not open |
| *@QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS |
| * Signed 32-bit value; 5GHz RSSI score bonus applied to all |
| * 5GHz networks |
| *@QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID |
| * Unsigned 32-bit value, representing the PNO Request ID |
| * @QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_PNO_MAX: max |
| */ |
| enum qca_wlan_vendor_attr_pno_config_params { |
| QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1, |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2, |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3, |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4, |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5, |
| QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6, |
| |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7, |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8, |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9, |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD = 10, |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11, |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12, |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13, |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14, |
| QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15, |
| QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16, |
| QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17, |
| QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18, |
| QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19, |
| QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20, |
| QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21, |
| QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22, |
| |
| QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PNO_MAX = |
| QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roaming_config_params - roaming config params |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD: roaming sub command |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID: Request id |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS: |
| * number of whitelist networks |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST: |
| * Whitelist ssid list |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID: |
| * white list ssid |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD: |
| * 'a' band boost threshold |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD: |
| * 'a' band penalty threshold |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR: |
| * 'a' band boost factor |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR: |
| * 'a' band penalty factor |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST: |
| * 'a' band max boost |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS: |
| * lazy roam histeresys |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER: |
| * alert roam rssi trigger |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE: |
| * set lazy roam enable |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS: |
| * set bssid preference |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID: |
| * set lazy roam number of bssid |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID: |
| * set lazy roam bssid |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER: |
| * set lazy roam rssi modifier |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS: |
| * set bssid params |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID: |
| * set bssid params num bssid |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID: |
| * set bssid params bssid |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX: Max |
| */ |
| enum qca_wlan_vendor_attr_roaming_config_params { |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2, |
| |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5, |
| |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12, |
| |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13, |
| |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17, |
| |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_roam_subcmd - roam sub commands |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST: ssid white list |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_EXTSCAN_ROAM_PARAMS: roam params |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM: set lazy roam |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS: set bssid prefs |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS: set bssid params |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID: set blacklist bssid |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX: subcmd max |
| */ |
| enum qca_wlan_vendor_attr_roam_subcmd { |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1, |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_EXTSCAN_ROAM_PARAMS = 2, |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3, |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4, |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5, |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6, |
| |
| /* KEEP LAST */ |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX = |
| QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_wifi_info - wifi driver information |
| * |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION: get host driver version |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION: ger firmware version |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX - get radio index |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX: subcmd max |
| */ |
| enum qca_wlan_vendor_attr_get_wifi_info { |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1, |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2, |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX = 3, |
| |
| /* KEEP LAST */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX = |
| QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1, |
| }; |
| |
| enum qca_wlan_vendor_attr_logger_results { |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0, |
| |
| /* |
| * Unsigned 32-bit value; must match the request Id supplied by |
| * Wi-Fi HAL in the corresponding subcmd NL msg. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1, |
| |
| /* |
| * Unsigned 32-bit value; used to indicate the size of memory |
| * dump to be allocated. |
| */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX = |
| QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel. |
| * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS. |
| */ |
| enum qca_wlan_vendor_channel_prop_flags { |
| /* Bits 0, 1, 2, and 3 are reserved */ |
| |
| /* Turbo channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4, |
| /* CCK channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5, |
| /* OFDM channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6, |
| /* 2.4 GHz spectrum channel. */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7, |
| /* 5 GHz spectrum channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8, |
| /* Only passive scan allowed */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9, |
| /* Dynamic CCK-OFDM channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10, |
| /* GFSK channel (FHSS PHY) */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11, |
| /* Radar found on channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12, |
| /* 11a static turbo channel only */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13, |
| /* Half rate channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14, |
| /* Quarter rate channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15, |
| /* HT 20 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16, |
| /* HT 40 with extension channel above */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17, |
| /* HT 40 with extension channel below */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18, |
| /* HT 40 intolerant */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19, |
| /* VHT 20 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20, |
| /* VHT 40 with extension channel above */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21, |
| /* VHT 40 with extension channel below */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22, |
| /* VHT 80 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23, |
| /* HT 40 intolerant mark bit for ACS use */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24, |
| /* Channel temporarily blocked due to noise */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25, |
| /* VHT 160 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26, |
| /* VHT 80+80 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27, |
| /* HE 20 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28, |
| /* HE 40 with extension channel above */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29, |
| /* HE 40 with extension channel below */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30, |
| /* HE 40 intolerant */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31, |
| }; |
| |
| /** |
| * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a |
| * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is |
| * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2. |
| */ |
| enum qca_wlan_vendor_channel_prop_flags_2 { |
| /* HE 40 intolerant mark bit for ACS use */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0, |
| /* HE 80 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1, |
| /* HE 160 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2, |
| /* HE 80+80 channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3, |
| }; |
| |
| /** |
| * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for |
| * each channel. This is used by |
| * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT. |
| */ |
| enum qca_wlan_vendor_channel_prop_flags_ext { |
| /* Radar found on channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0, |
| /* DFS required on channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1, |
| /* DFS required on channel for 2nd band of 80+80 */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2, |
| /* If channel has been checked for DFS */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3, |
| /* Excluded in 802.11d */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4, |
| /* Channel Switch Announcement received on this channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5, |
| /* Ad-hoc is not allowed */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6, |
| /* Station only channel */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7, |
| /* DFS radar history for slave device (STA mode) */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8, |
| /* DFS CAC valid for slave device (STA mode) */ |
| QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9, |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite |
| * information to start/stop the NUD statistics collection. |
| */ |
| enum qca_attr_nud_stats_set { |
| QCA_ATTR_NUD_STATS_SET_INVALID = 0, |
| |
| /* |
| * Flag to start/stop the NUD statistics collection. |
| * Start - If included, Stop - If not included |
| */ |
| QCA_ATTR_NUD_STATS_SET_START = 1, |
| /* IPv4 address of the default gateway (in network byte order) */ |
| QCA_ATTR_NUD_STATS_GW_IPV4 = 2, |
| /* |
| * Represents the data packet type to be monitored. |
| * Host driver tracks the stats corresponding to each data frame |
| * represented by these flags. |
| * These data packets are represented by |
| * enum qca_wlan_vendor_nud_stats_set_data_pkt_info. |
| */ |
| QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3, |
| /* keep last */ |
| QCA_ATTR_NUD_STATS_SET_LAST, |
| QCA_ATTR_NUD_STATS_SET_MAX = |
| QCA_ATTR_NUD_STATS_SET_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_attr_connectivity_check_stats_set - attribute to vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite |
| * information to start / stop the NUD stats collection. |
| * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_STATS_PKT_INFO_TYPE: set pkt info stats |
| * Bitmap to Flag to Start / Stop the NUD stats collection |
| * Start - If included , Stop - If not included |
| * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DNS_DOMAIN_NAME: set gatway ipv4 address |
| * IPv4 address of Default Gateway (in network byte order) |
| * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite |
| * information to start / stop the NUD stats collection. |
| * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_SRC_PORT: set nud debug stats |
| * Flag to Start / Stop the NUD stats collection |
| * Start - If included , Stop - If not included |
| * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_PORT: set gatway ipv4 address |
| * IPv4 address of Default Gateway (in network byte order) |
| * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carry the requisite |
| * information to start / stop the NUD stats collection. |
| * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV4: set nud debug stats |
| * Flag to Start / Stop the NUD stats collection |
| * Start - If included , Stop - If not included |
| * @QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV6: set gatway ipv4 address |
| * IPv4 address of Default Gateway (in network byte order) |
| */ |
| enum qca_attr_connectivity_check_stats_set { |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_INVALID = 0, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_STATS_PKT_INFO_TYPE = 1, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_DNS_DOMAIN_NAME = 2, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_SRC_PORT = 3, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_PORT = 4, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV4 = 5, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_DEST_IPV6 = 6, |
| /* keep last */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_LAST, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_MAX = |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_SET_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various |
| * data types for which the stats have to get collected. |
| */ |
| enum qca_wlan_vendor_connectivity_check_pkt_flags { |
| QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ARP = 1 << 0, |
| QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_DNS = 1 << 1, |
| QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_HANDSHAKE = 1 << 2, |
| QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ICMPV4 = 1 << 3, |
| QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_ICMPV6 = 1 << 4, |
| /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get |
| * to represent the stats of respective data type. |
| */ |
| QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_SYN = 1 << 5, |
| QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_SYN_ACK = 1 << 6, |
| QCA_WLAN_VENDOR_CONNECTIVITY_CHECK_SET_TCP_ACK = 1 << 7, |
| }; |
| |
| enum qca_attr_connectivity_check_stats { |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_INVALID = 0, |
| /* Data packet type for which the stats are collected. |
| * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags |
| */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_TYPE = 1, |
| /* ID corresponding to the DNS frame for which the respective DNS stats |
| * are monitored (u32). |
| */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DNS_DOMAIN_NAME = 2, |
| /* source / destination port on which the respective proto stats are |
| * collected (u32). |
| */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_SRC_PORT = 3, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_PORT = 4, |
| /* IPv4/IPv6 address for which the destined data packets are |
| * monitored. (in network byte order) |
| */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_IPV4 = 5, |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_DEST_IPV6 = 6, |
| /* Data packet Request count received from netdev */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7, |
| /* Data packet Request count sent to lower MAC from upper MAC */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8, |
| /* Data packet Request count received by lower MAC from upper MAC */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9, |
| /* Data packet Request count successfully transmitted by the device */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10, |
| /* Data packet Response count received by lower MAC */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11, |
| /* Data packet Response count received by upper MAC */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12, |
| /* Data packet Response count delivered to netdev */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_COUNT_TO_NETDEV = 13, |
| /* Data Packet Response count that are dropped out of order */ |
| QCA_ATTR_CONNECTIVITY_CHECK_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14, |
| |
| /* keep last */ |
| QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_LAST, |
| QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_MAX = |
| QCA_ATTR_CONNECTIVITY_CHECK_DATA_STATS_LAST - 1, |
| }; |
| |
| /** |
| * qca_attr_nud_stats_get: Attributes to vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite |
| * NUD statistics collected when queried. |
| */ |
| enum qca_attr_nud_stats_get { |
| QCA_ATTR_NUD_STATS_GET_INVALID = 0, |
| /* ARP Request count from netdev */ |
| QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1, |
| /* ARP Request count sent to lower MAC from upper MAC */ |
| QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2, |
| /* ARP Request count received by lower MAC from upper MAC */ |
| QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3, |
| /* ARP Request count successfully transmitted by the device */ |
| QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4, |
| /* ARP Response count received by lower MAC */ |
| QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5, |
| /* ARP Response count received by upper MAC */ |
| QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6, |
| /* ARP Response count delivered to netdev */ |
| QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7, |
| /* ARP Response count delivered to netdev */ |
| QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8, |
| /* |
| * Flag indicating if the station's link to the AP is active. |
| * Active Link - If included, Inactive link - If not included |
| */ |
| QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9, |
| /* |
| * Flag indicating if there is any duplicate address detected (DAD). |
| * Yes - If detected, No - If not detected. |
| */ |
| QCA_ATTR_NUD_STATS_IS_DAD = 10, |
| /* |
| * List of Data types for which the stats are requested. |
| * This list does not carry ARP stats as they are done by the |
| * above attributes. Represented by enum qca_attr_nud_data_stats. |
| */ |
| QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11, |
| /* keep last */ |
| QCA_ATTR_NUD_STATS_GET_LAST, |
| QCA_ATTR_NUD_STATS_GET_MAX = |
| QCA_ATTR_NUD_STATS_GET_LAST - 1, |
| }; |
| |
| enum qca_wlan_btm_candidate_status { |
| QCA_STATUS_ACCEPT = 0, |
| QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1, |
| QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2, |
| QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3, |
| QCA_STATUS_REJECT_LOW_RSSI = 4, |
| QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5, |
| QCA_STATUS_REJECT_UNKNOWN = 6, |
| }; |
| |
| enum qca_wlan_vendor_attr_btm_candidate_info { |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0, |
| |
| /* 6-byte MAC address representing the BSSID of transition candidate */ |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1, |
| /* |
| * Unsigned 32-bit value from enum qca_wlan_btm_candidate_status |
| * returned by the driver. It says whether the BSSID provided in |
| * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by |
| * the driver, if not it specifies the reason for rejection. |
| * Note that the user-space can overwrite the transition reject reason |
| * codes provided by driver based on more information. |
| */ |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1, |
| }; |
| |
| enum qca_attr_trace_level { |
| QCA_ATTR_TRACE_LEVEL_INVALID = 0, |
| /* |
| * Nested array of the following attributes: |
| * QCA_ATTR_TRACE_LEVEL_MODULE, |
| * QCA_ATTR_TRACE_LEVEL_MASK. |
| */ |
| QCA_ATTR_TRACE_LEVEL_PARAM = 1, |
| /* |
| * Specific QCA host driver module. Please refer to the QCA host |
| * driver implementation to get the specific module ID. |
| */ |
| QCA_ATTR_TRACE_LEVEL_MODULE = 2, |
| /* Different trace level masks represented in the QCA host driver. */ |
| QCA_ATTR_TRACE_LEVEL_MASK = 3, |
| |
| /* keep last */ |
| QCA_ATTR_TRACE_LEVEL_AFTER_LAST, |
| QCA_ATTR_TRACE_LEVEL_MAX = |
| QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_logger_features - value for logger |
| * supported features |
| * @QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID - Invalid |
| * @QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED - Indicate the supported features |
| * @QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - To keep track of the last enum |
| * @QCA_WLAN_VENDOR_ATTR_LOGGER_MAX - max value possible for this type |
| * |
| * enum values are used for NL attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET sub command. |
| */ |
| enum qca_wlan_vendor_attr_get_logger_features { |
| QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LOGGER_MAX = |
| QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_link_properties - link properties |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID: Invalid initial value |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_NSS: Unsigned 8-bit value to |
| * specify the number of spatial streams negotiated |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_RATE_FLAGS: Unsigned 8-bit value |
| * to specify negotiated rate flags i.e. ht, vht and channel width |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_FREQ: Unsigned 32bit value to |
| * specify the operating frequency |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC Address of the peer |
| * (STA / AP ) for the connected link. |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a |
| * &struct nl80211_sta_flag_update for the respective connected link. MAC |
| * address of the peer represented by |
| * QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR. |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAX: max value |
| */ |
| enum qca_wlan_vendor_attr_link_properties { |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_NSS = 1, |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_RATE_FLAGS = 2, |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_FREQ = 3, |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR = 4, |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS = 5, |
| |
| /* KEEP LAST */ |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAX = |
| QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_nd_offload - vendor NS offload support |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID - Invalid |
| * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG - Flag to set NS offload |
| * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - To keep track of the last enum |
| * @QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX - max value possible for this type |
| * |
| * enum values are used for NL attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD sub command. |
| */ |
| enum qca_wlan_vendor_attr_nd_offload { |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG, |
| |
| /* Keep last */ |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX = |
| QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_features - vendor device/driver features |
| * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key |
| * management offload, a mechanism where the station's firmware |
| * does the exchange with the AP to establish the temporal keys |
| * after roaming, rather than having the supplicant do it. |
| * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports |
| * simultaneous off-channel operations. |
| * @QQCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P |
| * Listen offload; a mechanism where the station's firmware |
| * takes care of responding to incoming Probe Request frames received |
| * from other P2P devices whilst in Listen state, rather than having the |
| * user space wpa_supplicant do it. Information from received P2P |
| * Requests are forwarded from firmware to host whenever the APPS |
| * processor exits power collapse state. |
| * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA |
| * specific features |
| * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific |
| * features. |
| * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON |
| * specific features only. If a Device sets this bit but not the |
| * QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that |
| * this Device may not support all OCE AP functionalities but can support |
| * only OCE STA-CFON functionalities. |
| * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self |
| * managed regulatory. |
| */ |
| enum qca_wlan_vendor_features { |
| QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0, |
| QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1, |
| QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2, |
| QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3, |
| QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4, |
| QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5, |
| QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6, |
| QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7, |
| /* Additional features need to be added above this */ |
| NUM_QCA_WLAN_VENDOR_FEATURES |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for SAP |
| * conditional channel switch |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID: Invalid initial |
| * value |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST: Priority based |
| * frequency list (an array of u32 values in host byte order) |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS: Status of the |
| * conditional switch (u32)- 0: Success, Non-zero: Failure |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST: After last |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX: Subcommand max |
| */ |
| enum qca_wlan_vendor_attr_sap_conditional_chan_switch { |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2, |
| |
| /* Keep Last */ |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX = |
| QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum wifi_logger_supported_features - values for supported logger features |
| * @WIFI_LOGGER_MEMORY_DUMP_SUPPORTED: Memory dump of FW |
| * @WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_SUPPORTED: Per packet statistics |
| * @WIFI_LOGGER_CONNECT_EVENT_SUPPORTED: Logging of Connectivity events |
| * @WIFI_LOGGER_POWER_EVENT_SUPPORTED: Power of driver |
| * @WIFI_LOGGER_WAKE_LOCK_SUPPORTE: Wakelock of driver |
| * @WIFI_LOGGER_WATCHDOG_TIMER_SUPPORTED: monitor FW health |
| * @WIFI_LOGGER_DRIVER_DUMP_SUPPORTED: support driver dump |
| * @WIFI_LOGGER_PACKET_FATE_SUPPORTED: tracks connection packets fate |
| */ |
| enum wifi_logger_supported_features { |
| WIFI_LOGGER_MEMORY_DUMP_SUPPORTED = (1 << (0)), |
| WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_SUPPORTED = (1 << (1)), |
| WIFI_LOGGER_CONNECT_EVENT_SUPPORTED = (1 << (2)), |
| WIFI_LOGGER_POWER_EVENT_SUPPORTED = (1 << (3)), |
| WIFI_LOGGER_WAKE_LOCK_SUPPORTED = (1 << (4)), |
| WIFI_LOGGER_VERBOSE_SUPPORTED = (1 << (5)), |
| WIFI_LOGGER_WATCHDOG_TIMER_SUPPORTED = (1 << (6)), |
| WIFI_LOGGER_DRIVER_DUMP_SUPPORTED = (1 << (7)), |
| WIFI_LOGGER_PACKET_FATE_SUPPORTED = (1 << (8)) |
| }; |
| /** |
| * enum qca_wlan_vendor_attr_acs_offload |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL: ACS selected primary channel |
| * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL: ACS selected secondary channel |
| * @QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE: hw_mode for ACS |
| * @QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED: indicate if HT capability is enabled |
| * @QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED: indicate HT capability |
| */ |
| enum qca_wlan_vendor_attr_acs_offload { |
| QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE, |
| QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED, |
| QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED, |
| QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED, |
| QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH, |
| QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST, |
| QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ACS_MAX = |
| QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_acs_hw_mode |
| * |
| * @QCA_ACS_MODE_IEEE80211B: 11b mode |
| * @QCA_ACS_MODE_IEEE80211G: 11g mode |
| * @QCA_ACS_MODE_IEEE80211A: 11a mode |
| * @QCA_ACS_MODE_IEEE80211AD: 11ad mode |
| */ |
| enum qca_wlan_vendor_acs_hw_mode { |
| QCA_ACS_MODE_IEEE80211B, |
| QCA_ACS_MODE_IEEE80211G, |
| QCA_ACS_MODE_IEEE80211A, |
| QCA_ACS_MODE_IEEE80211AD, |
| QCA_ACS_MODE_IEEE80211ANY, |
| }; |
| |
| /** |
| * enum qca_access_policy - access control policy |
| * |
| * Access control policy is applied on the configured IE |
| * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE). |
| * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY. |
| * |
| * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi Connections which match |
| *» with the specific configuration (IE) set, i.e. allow all the |
| *» connections which do not match the configuration. |
| * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi Connections which match |
| *» with the specific configuration (IE) set, i.e. deny all the |
| *» connections which do not match the configuration. |
| */ |
| enum qca_access_policy { |
| QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED, |
| QCA_ACCESS_POLICY_DENY_UNLESS_LISTED, |
| }; |
| |
| /** |
| * enum qca_ignore_assoc_disallowed - Ignore assoc disallowed values |
| * |
| * The valid values for the ignore assoc disallowed |
| * |
| * @QCA_IGNORE_ASSOC_DISALLOWED_DISABLE: Disable ignore assoc disallowed |
| * @QCA_IGNORE_ASSOC_DISALLOWED_ENABLE: Enable ignore assoc disallowed |
| * |
| */ |
| enum qca_ignore_assoc_disallowed { |
| QCA_IGNORE_ASSOC_DISALLOWED_DISABLE, |
| QCA_IGNORE_ASSOC_DISALLOWED_ENABLE |
| }; |
| |
| /* Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and |
| * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. |
| */ |
| enum qca_wlan_vendor_attr_config { |
| QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, |
| /* |
| * Unsigned 32-bit value to set the DTIM period. |
| * Whether the wifi chipset wakes at every dtim beacon or a multiple of |
| * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 |
| * DTIM beacons. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_MODULATED_DTIM = 1, |
| /* |
| * Unsigned 32-bit value to set the wifi_iface stats averaging factor |
| * used to calculate statistics like average the TSF offset or average |
| * number of frame leaked. |
| * For instance, upon Beacon frame reception: |
| * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000 |
| * For instance, when evaluating leaky APs: |
| * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, |
| /* |
| * Unsigned 32-bit value to configure guard time, i.e., when |
| * implementing IEEE power management based on frame control PM bit, how |
| * long the driver waits before shutting down the radio and after |
| * receiving an ACK frame for a Data frame with PM bit set. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, |
| /* Unsigned 32-bit value to change the FTM capability dynamically */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, |
| /* Unsigned 16-bit value to configure maximum TX rate dynamically */ |
| QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, |
| /* |
| * Unsigned 32-bit value to configure the number of continuous |
| * Beacon Miss which shall be used by the firmware to penalize |
| * the RSSI. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, |
| /* |
| * Unsigned 8-bit value to configure the channel avoidance indication |
| * behavior. Firmware to send only one indication and ignore duplicate |
| * indications when set to avoid multiple Apps wakeups. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, |
| /* |
| * 8-bit unsigned value to configure the maximum TX MPDU for |
| * aggregation. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, |
| /* |
| * 8-bit unsigned value to configure the maximum RX MPDU for |
| * aggregation. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, |
| /* |
| * 8-bit unsigned value to configure the Non aggregrate/11g sw |
| * retry threshold (0 disable, 31 max). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, |
| /* |
| * 8-bit unsigned value to configure the aggregrate sw |
| * retry threshold (0 disable, 31 max). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, |
| /* |
| * 8-bit unsigned value to configure the MGMT frame |
| * retry threshold (0 disable, 31 max). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, |
| /* |
| * 8-bit unsigned value to configure the CTRL frame |
| * retry threshold (0 disable, 31 max). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, |
| /* |
| * 8-bit unsigned value to configure the propagation delay for |
| * 2G/5G band (0~63, units in us) |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, |
| /* |
| * Unsigned 32-bit value to configure the number of unicast TX fail |
| * packet count. The peer is disconnected once this threshold is |
| * reached. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, |
| /* |
| * Attribute used to set scan default IEs to the driver. |
| * |
| * These IEs can be used by scan operations that will be initiated by |
| * the driver/firmware. |
| * |
| * For further scan requests coming to the driver, these IEs should be |
| * merged with the IEs received along with scan request coming to the |
| * driver. If a particular IE is present in the scan default IEs but not |
| * present in the scan request, then that IE should be added to the IEs |
| * sent in the Probe Request frames for that scan request. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, |
| /* Unsigned 32-bit attribute for generic commands */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, |
| /* Unsigned 32-bit value attribute for generic commands */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, |
| /* Unsigned 32-bit data attribute for generic command response */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, |
| /* |
| * Unsigned 32-bit length attribute for |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, |
| /* |
| * Unsigned 32-bit flags attribute for |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, |
| /* |
| * Unsigned 32-bit, defining the access policy. |
| * See enum qca_access_policy. Used with |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, |
| /* |
| * Sets the list of full set of IEs for which a specific access policy |
| * has to be applied. Used along with |
| * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. |
| * Zero length payload can be used to clear this access constraint. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, |
| /* |
| * Unsigned 32-bit, specifies the interface index (netdev) for which the |
| * corresponding configurations are applied. If the interface index is |
| * not specified, the configurations are attributed to the respective |
| * wiphy. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, |
| /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, |
| /* |
| * 8-bit unsigned value to configure the driver and below layers to |
| * ignore the assoc disallowed set by APs while connecting |
| * 1-Ignore, 0-Don't ignore |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, |
| /* |
| * 32-bit unsigned value to trigger antenna diversity features: |
| * 1-Enable, 0-Disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, |
| /* 32-bit unsigned value to configure specific chain antenna */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, |
| /* |
| * 32-bit unsigned value to trigger cycle selftest |
| * 1-Enable, 0-Disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, |
| /* |
| * 32-bit unsigned to configure the cycle time of selftest |
| * the unit is micro-second |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, |
| /* 32-bit unsigned value to set reorder timeout for AC_VO */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31, |
| /* 32-bit unsigned value to set reorder timeout for AC_VI */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32, |
| /* 32-bit unsigned value to set reorder timeout for AC_BE */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33, |
| /* 32-bit unsigned value to set reorder timeout for AC_BK */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34, |
| /* 6-byte MAC address to point out the specific peer */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35, |
| /* 32-bit unsigned value to set window size for specific peer */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36, |
| /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37, |
| /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38, |
| /* |
| * 32-bit unsigned value to configure 5 or 10 MHz channel width for |
| * station device while in disconnect state. The attribute use the |
| * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz, |
| * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or |
| * 10 MHz channel width, the station will not connect to a BSS using 20 |
| * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to |
| * clear this constraint. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39, |
| /* |
| * 32-bit unsigned value to configure the propagation absolute delay |
| * for 2G/5G band (units in us) |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40, |
| /* 32-bit unsigned value to set probe period */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41, |
| /* 32-bit unsigned value to set stay period */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42, |
| /* 32-bit unsigned value to set snr diff */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43, |
| /* 32-bit unsigned value to set probe dwell time */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44, |
| /* 32-bit unsigned value to set mgmt snr weight */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45, |
| /* 32-bit unsigned value to set data snr weight */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46, |
| /* 32-bit unsigned value to set ack snr weight */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47, |
| /* |
| * 32-bit unsigned value to configure the listen interval. |
| * This is in units of beacon intervals. This configuration alters |
| * the negotiated listen interval with the AP during the connection. |
| * It is highly recommended to configure a value less than or equal to |
| * the one negotiated during the association. Configuring any greater |
| * value can have adverse effects (frame loss, AP disassociating STA, |
| * etc.). |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48, |
| /* |
| * 8 bit unsigned value that is set on an AP/GO virtual interface to |
| * disable operations that would cause the AP/GO to leave its operating |
| * channel. |
| * |
| * This will restrict the scans to the AP/GO operating channel and the |
| * channels of the other band, if DBS is supported.A STA/CLI interface |
| * brought up after this setting is enabled, will be restricted to |
| * connecting to devices only on the AP/GO interface's operating channel |
| * or on the other band in DBS case. P2P supported channel list is |
| * modified, to only include AP interface's operating-channel and the |
| * channels of the other band if DBS is supported. |
| * |
| * These restrictions are only applicable as long as the AP/GO interface |
| * is alive. If the AP/GO interface is brought down then this |
| * setting/restriction is forgotten. |
| * |
| * If this variable is set on an AP/GO interface while a multi-channel |
| * concurrent session is active, it has no effect on the operation of |
| * the current interfaces, other than restricting the scan to the AP/GO |
| * operating channel and the other band channels if DBS is supported. |
| * However, if the STA is brought down and restarted then the new STA |
| * connection will either be formed on the AP/GO channel or on the |
| * other band in a DBS case. This is because of the scan being |
| * restricted on these channels as mentioned above. |
| * |
| * 1-Disable offchannel operations, 0-Enable offchannel operations. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49, |
| |
| /* |
| * 8 bit unsigned value to enable/disable LRO (Large Receive Offload) |
| * on an interface. |
| * 1 - Enable , 0 - Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50, |
| |
| /* |
| * 8 bit unsigned value to globally enable/disable scan |
| * 1 - Enable, 0 - Disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51, |
| |
| /* 8-bit unsigned value to set the total beacon miss count */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52, |
| |
| /* |
| * Unsigned 32-bit value to configure the number of continuous |
| * Beacon Miss which shall be used by the firmware to penalize |
| * the RSSI for BTC. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53, |
| |
| /* |
| * 8-bit unsigned value to configure the driver and below layers to |
| * enable/disable all fils features. |
| * 0-enable, 1-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54, |
| |
| /* 16-bit unsigned value to configure the level of WLAN latency |
| * module. See enum qca_wlan_vendor_attr_config_latency_level. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55, |
| |
| /* |
| * 8-bit unsigned value indicating the driver to use the RSNE as-is from |
| * the connect interface. Exclusively used for the scenarios where the |
| * device is used as a test bed device with special functionality and |
| * not recommended for production. This helps driver to not validate the |
| * RSNE passed from user space and thus allow arbitrary IE data to be |
| * used for testing purposes. |
| * 1-enable, 0-disable. |
| * Applications set/reset this configuration. If not reset, this |
| * parameter remains in use until the driver is unloaded. |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56, |
| |
| /* |
| * 8-bit unsigned value to trigger green Tx power saving. |
| * 1-Enable, 0-Disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_wifi_logger_start - Enum for wifi logger starting |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID: Invalid attribute |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID: Ring ID |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL: Verbose level |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS: Flag |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST: Last value |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_wifi_logger_start { |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_MAX = |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1, |
| }; |
| |
| /* |
| * enum qca_wlan_vendor_attr_wifi_logger_get_ring_data - Get ring data |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_INVALID: Invalid attribute |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_ID: Ring ID |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST: Last value |
| * @QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_MAX: Max value |
| */ |
| enum qca_wlan_vendor_attr_wifi_logger_get_ring_data { |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_ID = 1, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_MAX = |
| QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_GET_RING_DATA_AFTER_LAST - 1, |
| }; |
| |
| #ifdef WLAN_FEATURE_OFFLOAD_PACKETS |
| /** |
| * enum wlan_offloaded_packets_control - control commands |
| * @WLAN_START_OFFLOADED_PACKETS: start offloaded packets |
| * @WLAN_STOP_OFFLOADED_PACKETS: stop offloaded packets |
| * |
| */ |
| enum wlan_offloaded_packets_control { |
| WLAN_START_OFFLOADED_PACKETS = 1, |
| WLAN_STOP_OFFLOADED_PACKETS = 2 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to |
| * the offloaded data. |
| * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded |
| * data. |
| * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload |
| * indication. |
| */ |
| enum qca_wlan_vendor_attr_data_offload_ind { |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION, |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL, |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX = |
| QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_offloaded_packets - offloaded packets |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID: invalid |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL: control |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID: request id |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA: ip packet data |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR: src mac address |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR: destination mac address |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD: period in milli seconds |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX: max |
| */ |
| enum qca_wlan_vendor_attr_offloaded_packets { |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL, |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID, |
| |
| /* Packet in hex format */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA, |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX = |
| QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1, |
| }; |
| #endif |
| |
| /** |
| * enum qca_wlan_rssi_monitoring_control - rssi control commands |
| * @QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID: invalid |
| * @QCA_WLAN_RSSI_MONITORING_START: rssi monitoring start |
| * @QCA_WLAN_RSSI_MONITORING_STOP: rssi monitoring stop |
| */ |
| enum qca_wlan_rssi_monitoring_control { |
| QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0, |
| QCA_WLAN_RSSI_MONITORING_START, |
| QCA_WLAN_RSSI_MONITORING_STOP, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_rssi_monitoring - rssi monitoring |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID: Invalid |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL: control |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI: max rssi |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI: min rssi |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID: current bssid |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI: current rssi |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX: max |
| */ |
| enum qca_wlan_vendor_attr_rssi_monitoring { |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL, |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID, |
| |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI, |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI, |
| |
| /* attributes to be used/received in callback */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID, |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX = |
| QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_NDP. |
| * @QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID |
| * @QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD: sub commands values in qca_wlan_ndp_sub_cmd |
| * @QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID: |
| * @QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID: indicats a service info |
| * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL: channel frequency in MHz |
| * @QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR: Interface Discovery MAC |
| * address |
| * @QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR: Interface name on which NDP is being |
| * created |
| * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY: CONFIG_SECURITY is deprecated, use |
| * NCS_SK_TYPE/PMK/SCID instead |
| * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS: value for QoS |
| * @QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO: app info |
| * @QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID: NDP instance Id |
| * @QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY: Array of instance Ids |
| * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE: initiator/responder NDP response |
| * code: accept/reject |
| * @QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR: NDI MAC address |
| * @QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE: errors types returned by |
| * driver |
| * @QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE: value error values returned by |
| * driver |
| * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG: Channel setup configuration |
| * @QCA_WLAN_VENDOR_ATTR_NDP_CSID: Cipher Suite Shared Key Type |
| * @QCA_WLAN_VENDOR_ATTR_NDP_PMK: PMK_INFO |
| * @QCA_WLAN_VENDOR_ATTR_NDP_SCID: Security Context Identifier that contains the |
| * PMKID |
| * @QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE: passphrase |
| * @QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME: service name |
| * @QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON: bitmap indicating schedule |
| * update: |
| * BIT_0: NSS Update |
| * BIT_1: Channel list update |
| * @QCA_WLAN_VENDOR_ATTR_NDP_NSS: nss |
| * @QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS: NUMBER NDP CHANNEL |
| * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH: CHANNEL BANDWIDTH: |
| * 0:20 MHz, |
| * 1:40 MHz, |
| * 2:80 MHz, |
| * 3:160 MHz |
| * @QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO: Array of channel/band width |
| * @QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST: id after last valid attribute |
| * @QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX: max value of this enum type |
| * @QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR: IPv6 address used by NDP, 16 bytes array |
| * @QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT: Unsigned 16-bit value indicating |
| * transport port used by NDP. |
| * QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL: Unsigned 8-bit value indicating |
| * protocol used by NDP and assigned by the Internet Assigned Numbers Authority |
| * as per: www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml |
| */ |
| enum qca_wlan_vendor_attr_ndp_params { |
| QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD = 1, |
| QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID = 2, |
| QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID = 3, |
| QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL = 4, |
| QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR = 5, |
| QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR = 6, |
| QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY = 7, |
| QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS = 8, |
| QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO = 9, |
| QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID = 10, |
| QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY = 11, |
| QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE = 12, |
| QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR = 13, |
| QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE = 14, |
| QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE = 15, |
| QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG = 16, |
| QCA_WLAN_VENDOR_ATTR_NDP_CSID = 17, |
| QCA_WLAN_VENDOR_ATTR_NDP_PMK = 18, |
| QCA_WLAN_VENDOR_ATTR_NDP_SCID = 19, |
| QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE = 20, |
| QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME = 21, |
| QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON = 22, |
| QCA_WLAN_VENDOR_ATTR_NDP_NSS = 23, |
| QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS = 24, |
| QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH = 25, |
| QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO = 26, |
| QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27, |
| QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28, |
| QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX = |
| QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_ndp_sub_cmd - NDP sub comands types for |
| * QCA_NL80211_VENDOR_SUBCMD_NDP. |
| * @QCA_WLAN_VENDOR_ATTR_NDP_INVALID: invalid value |
| * @QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE: create a ndi |
| * @QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE: delete a ndi |
| * @QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST: initiate a ndp session |
| * @QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE: response for above |
| * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST: respond to ndp session |
| * @QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE: response for above |
| * @QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST: initiate a ndp end |
| * @QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE: response for above |
| * @QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND: notify the peer about the end request |
| * @QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND: confirm the ndp session is complete |
| * @QCA_WLAN_VENDOR_ATTR_NDP_END_IND: indicate the peer about the end request |
| * being received |
| * @QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND: indicate the peer of schedule |
| * update |
| */ |
| enum qca_wlan_ndp_sub_cmd { |
| QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1, |
| QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2, |
| QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3, |
| QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4, |
| QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5, |
| QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6, |
| QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7, |
| QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8, |
| QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9, |
| QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10, |
| QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11, |
| QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12 |
| }; |
| |
| /** |
| * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel |
| * information. These attributes are sent as part of |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following |
| * attributes correspond to a single channel. |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS: A bitmask (u16) |
| * with flags specified in qca_wlan_vendor_channel_prop_flags_ext. |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT: A bitmask (u16) |
| * with flags specified in qca_wlan_vendor_channel_prop_flags_ext. |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ: frequency |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER: maximum |
| * regulatory transmission power |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER: maximum |
| * transmission power |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER: minimum |
| * transmission power |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID: regulatory |
| * class id |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN: maximum |
| * antenna gain in dbm |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0: vht segment 0 |
| * @QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1: vht segment 1 |
| * |
| */ |
| enum qca_wlan_vendor_external_acs_event_chan_info_attr { |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10, |
| /* |
| * A bitmask (u32) with flags specified in |
| * enum qca_wlan_vendor_channel_prop_flags_2. |
| */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST, |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX = |
| QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_start_acs_config: attribute to vendor sub-command |
| * QCA_NL80211_VENDOR_SUBCMD_START_ACS. This will be triggered by host |
| * driver. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON: This reason refers to |
| * qca_wlan_vendor_acs_select_reason. This helps acs module to understand why |
| * ACS need to be started |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED: Does |
| * driver supports spectral scanning or not |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED: Is 11ac is |
| * offloaded to firmware. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT: Does driver |
| * provides additional channel capability as part of scan operation. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP:Flag attribute to indicate |
| * interface status is UP |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE: Operating mode of |
| * interface. It takes one of nl80211_iftype values. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH: This is the upper bound |
| * of chan width. ACS logic should try to get a channel with specified width |
| * if not found then look for lower values. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND: nl80211_bands |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE: PHY/HW mode such as |
| * a/b/g/n/ac. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST: Supported frequency list |
| * among which ACS should choose best frequency. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL:Preferred Chan List by the |
| * driver which will have <channel(u8), weight(u8)> format as array of |
| * nested values. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO: Array of nested attribute |
| * for each channel. It takes attr as defined in |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY:External ACS policy such as |
| * PCL mandatory, PCL preferred, etc.It uses values defined in enum |
| * qca_wlan_vendor_attr_external_acs_policy. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO: Reference RF |
| * Operating Parameter (RROP) availability information (u16). It uses values |
| * defined in enum qca_wlan_vendor_attr_rropavail_info. |
| */ |
| enum qca_wlan_vendor_attr_external_acs_event { |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX = |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1, |
| }; |
| |
| enum qca_iface_type { |
| QCA_IFACE_TYPE_STA, |
| QCA_IFACE_TYPE_AP, |
| QCA_IFACE_TYPE_P2P_CLIENT, |
| QCA_IFACE_TYPE_P2P_GO, |
| QCA_IFACE_TYPE_IBSS, |
| QCA_IFACE_TYPE_TDLS, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_pcl_config: attribute to vendor sub-command |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL. |
| * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_INVALID: invalid value |
| * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_CHANNEL: pcl channel number |
| * @QCA_WLAN_VENDOR_ATTR_PCL_CONFIG_WEIGHT: pcl channel weight |
| */ |
| enum qca_wlan_vendor_attr_pcl_config { |
| QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1, |
| QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2, |
| }; |
| |
| enum qca_set_band { |
| QCA_SETBAND_AUTO, |
| QCA_SETBAND_5G, |
| QCA_SETBAND_2G, |
| }; |
| |
| /** |
| * enum set_reset_packet_filter - set packet filter control commands |
| * @QCA_WLAN_SET_PACKET_FILTER: Set Packet Filter |
| * @QCA_WLAN_GET_PACKET_FILTER: Get Packet filter |
| * @QCA_WLAN_WRITE_PACKET_FILTER: Write packet filter program/data |
| * @QCA_WLAN_READ_PACKET_FILTER: Read packet filter program/data |
| * @QCA_WLAN_ENABLE_PACKET_FILTER: Enable APF interpreter |
| * @QCA_WLAN_DISABLE_PACKET_FILTER: Disable APF interpreter |
| */ |
| enum set_reset_packet_filter { |
| QCA_WLAN_SET_PACKET_FILTER = 1, |
| QCA_WLAN_GET_PACKET_FILTER = 2, |
| QCA_WLAN_WRITE_PACKET_FILTER = 3, |
| QCA_WLAN_READ_PACKET_FILTER = 4, |
| QCA_WLAN_ENABLE_PACKET_FILTER = 5, |
| QCA_WLAN_DISABLE_PACKET_FILTER = 6, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_packet_filter - APF control commands |
| * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID: Invalid |
| * @QCA_WLAN_VENDOR_ATTR_SET_RESET_PACKET_FILTER: Filter ID |
| * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION: Filter Version |
| * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE: Total Length |
| * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET: Current offset |
| * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM: length of APF instructions |
| * @QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH: length of the program |
| * section in packet filter buffer |
| */ |
| enum qca_wlan_vendor_attr_packet_filter { |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SET_RESET_PACKET_FILTER, |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION, |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID, |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE, |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET, |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM, |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX = |
| QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_wake_stats - wake lock stats |
| * @QCA_WLAN_VENDOR_ATTR_GET_WAKE_STATS_INVALID: invalid |
| * @QCA_WLAN_VENDOR_ATTR_TOTAL_CMD_EVENT_WAKE: |
| * @QCA_WLAN_VENDOR_ATTR_CMD_EVENT_WAKE_CNT_PTR: |
| * @QCA_WLAN_VENDOR_ATTR_CMD_EVENT_WAKE_CNT_SZ: |
| * @QCA_WLAN_VENDOR_ATTR_TOTAL_DRIVER_FW_LOCAL_WAKE: |
| * @QCA_WLAN_VENDOR_ATTR_DRIVER_FW_LOCAL_WAKE_CNT_PTR: |
| * @QCA_WLAN_VENDOR_ATTR_DRIVER_FW_LOCAL_WAKE_CNT_SZ: |
| * @QCA_WLAN_VENDOR_ATTR_TOTAL_RX_DATA_WAKE: |
| * total rx wakeup count |
| * @QCA_WLAN_VENDOR_ATTR_RX_UNICAST_CNT: |
| * Total rx unicast packet which woke up host |
| * @QCA_WLAN_VENDOR_ATTR_RX_MULTICAST_CNT: |
| * Total rx multicast packet which woke up host |
| * @QCA_WLAN_VENDOR_ATTR_RX_BROADCAST_CNT: |
| * Total rx broadcast packet which woke up host |
| * @QCA_WLAN_VENDOR_ATTR_ICMP_PKT: |
| * wake icmp packet count |
| * @QCA_WLAN_VENDOR_ATTR_ICMP6_PKT: |
| * wake icmp6 packet count |
| * @QCA_WLAN_VENDOR_ATTR_ICMP6_RA: |
| * wake icmp6 RA packet count |
| * @QCA_WLAN_VENDOR_ATTR_ICMP6_NA: |
| * wake icmp6 NA packet count |
| * @QCA_WLAN_VENDOR_ATTR_ICMP6_NS: |
| * wake icmp6 NS packet count |
| * @QCA_WLAN_VENDOR_ATTR_ICMP4_RX_MULTICAST_CNT: |
| * Rx wake packet count due to ipv4 multicast |
| * @QCA_WLAN_VENDOR_ATTR_ICMP6_RX_MULTICAST_CNT: |
| * Rx wake packet count due to ipv6 multicast |
| * @QCA_WLAN_VENDOR_ATTR_OTHER_RX_MULTICAST_CNT: |
| * Rx wake packet count due to non-ipv4 and non-ipv6 packets |
| * @QCA_WLAN_VENDOR_ATTR_RSSI_BREACH_CNT: |
| * wake rssi breach packet count |
| * @QCA_WLAN_VENDOR_ATTR_LOW_RSSI_CNT: |
| * wake low rssi packet count |
| * @QCA_WLAN_VENDOR_ATTR_GSCAN_CNT: |
| * wake gscan packet count |
| * @QCA_WLAN_VENDOR_ATTR_PNO_COMPLETE_CNT: |
| * wake pno complete packet count |
| * @QCA_WLAN_VENDOR_ATTR_PNO_MATCH_CNT: |
| * wake pno match packet count |
| */ |
| enum qca_wlan_vendor_attr_wake_stats { |
| QCA_WLAN_VENDOR_ATTR_GET_WAKE_STATS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TOTAL_CMD_EVENT_WAKE, |
| QCA_WLAN_VENDOR_ATTR_CMD_EVENT_WAKE_CNT_PTR, |
| QCA_WLAN_VENDOR_ATTR_CMD_EVENT_WAKE_CNT_SZ, |
| QCA_WLAN_VENDOR_ATTR_TOTAL_DRIVER_FW_LOCAL_WAKE, |
| QCA_WLAN_VENDOR_ATTR_DRIVER_FW_LOCAL_WAKE_CNT_PTR, |
| QCA_WLAN_VENDOR_ATTR_DRIVER_FW_LOCAL_WAKE_CNT_SZ, |
| QCA_WLAN_VENDOR_ATTR_TOTAL_RX_DATA_WAKE, |
| QCA_WLAN_VENDOR_ATTR_RX_UNICAST_CNT, |
| QCA_WLAN_VENDOR_ATTR_RX_MULTICAST_CNT, |
| QCA_WLAN_VENDOR_ATTR_RX_BROADCAST_CNT, |
| QCA_WLAN_VENDOR_ATTR_ICMP_PKT, |
| QCA_WLAN_VENDOR_ATTR_ICMP6_PKT, |
| QCA_WLAN_VENDOR_ATTR_ICMP6_RA, |
| QCA_WLAN_VENDOR_ATTR_ICMP6_NA, |
| QCA_WLAN_VENDOR_ATTR_ICMP6_NS, |
| QCA_WLAN_VENDOR_ATTR_ICMP4_RX_MULTICAST_CNT, |
| QCA_WLAN_VENDOR_ATTR_ICMP6_RX_MULTICAST_CNT, |
| QCA_WLAN_VENDOR_ATTR_OTHER_RX_MULTICAST_CNT, |
| QCA_WLAN_VENDOR_ATTR_RSSI_BREACH_CNT, |
| QCA_WLAN_VENDOR_ATTR_LOW_RSSI_CNT, |
| QCA_WLAN_VENDOR_ATTR_GSCAN_CNT, |
| QCA_WLAN_VENDOR_ATTR_PNO_COMPLETE_CNT, |
| QCA_WLAN_VENDOR_ATTR_PNO_MATCH_CNT, |
| /* keep last */ |
| QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST, |
| QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX = |
| QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_vendor_element_id - QCA Vendor Specific element types |
| * |
| * These values are used to identify QCA Vendor Specific elements. The |
| * payload of the element starts with the three octet OUI (OUI_QCA) and |
| * is followed by a single octet type which is defined by this enum. |
| * |
| * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list. |
| * This element can be used to specify preference order for supported |
| * channels. The channels in this list are in preference order (the first |
| * one has the highest preference) and are described as a pair of |
| * (global) Operating Class and Channel Number (each one octet) fields. |
| * |
| * This extends the standard P2P functionality by providing option to have |
| * more than one preferred operating channel. When this element is present, |
| * it replaces the preference indicated in the Operating Channel attribute. |
| * For supporting other implementations, the Operating Channel attribute is |
| * expected to be used with the highest preference channel. Similarly, all |
| * the channels included in this Preferred channel list element are |
| * expected to be included in the Channel List attribute. |
| * |
| * This vendor element may be included in GO Negotiation Request, P2P |
| * Invitation Request, and Provision Discovery Request frames. |
| * |
| * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element. |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID. The payload of this |
| * vendor specific element is defined by the latest P802.11ax draft. |
| * Please note that the draft is still work in progress and this element |
| * payload is subject to change. |
| * |
| * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element. |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID. The payload of this |
| * vendor specific element is defined by the latest P802.11ax draft. |
| * Please note that the draft is still work in progress and this element |
| * payload is subject to change. |
| * |
| * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set |
| * element). |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID extension. The payload of |
| * this vendor specific element is defined by the latest P802.11ax draft |
| * (not including the Element ID Extension field). Please note that the |
| * draft is still work in progress and this element payload is subject to |
| * change. |
| * |
| * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element. |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID extension. The payload of |
| * this vendor specific element is defined by the latest P802.11ax draft |
| * (not including the Element ID Extension field). Please note that the |
| * draft is still work in progress and this element payload is subject to |
| * change. |
| * |
| * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element. |
| * This element can be used for pre-standard publication testing of HE |
| * before P802.11ax draft assigns the element ID extension. The payload of |
| * this vendor specific element is defined by the latest P802.11ax draft |
| * (not including the Element ID Extension field). Please note that the |
| * draft is still work in progress and this element payload is subject to |
| * change. |
| */ |
| enum qca_vendor_element_id { |
| QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0, |
| QCA_VENDOR_ELEM_HE_CAPAB = 1, |
| QCA_VENDOR_ELEM_HE_OPER = 2, |
| QCA_VENDOR_ELEM_RAPS = 3, |
| QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4, |
| QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture |
| * @QCA_WLAN_VENDOR_ATTR_TSF_INVALID: Invalid attribute value |
| * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32) |
| * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value |
| * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized |
| * SOC timer value at TSF capture |
| * @QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_TSF_MAX: Max value |
| */ |
| enum qca_vendor_attr_tsf_cmd { |
| QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TSF_CMD, |
| QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE, |
| QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE, |
| QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TSF_MAX = |
| QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_tsf_operation: TSF driver commands |
| * @QCA_TSF_CAPTURE: Initiate TSF Capture |
| * @QCA_TSF_GET: Get TSF capture value |
| * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value |
| */ |
| enum qca_tsf_cmd { |
| QCA_TSF_CAPTURE, |
| QCA_TSF_GET, |
| QCA_TSF_SYNC_GET, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_get_preferred_freq_list - get preferred channel list |
| * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID: invalid value |
| * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE: interface type |
| * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST: preferred frequency list |
| * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX: max |
| */ |
| enum qca_vendor_attr_get_preferred_freq_list { |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID, |
| /* A 32-unsigned value; the interface type/mode for which the preferred |
| * frequency list is requested (see enum qca_iface_type for possible |
| * values); used in both south- and north-bound. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE, |
| /* An array of 32-unsigned values; values are frequency (MHz); used |
| * in north-bound only. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX = |
| QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_vendor_attr_probable_oper_channel - channel hint |
| * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID: invalid value |
| * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE: interface type |
| * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ: frequency hint value |
| * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST: last |
| * @QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX: max |
| */ |
| enum qca_vendor_attr_probable_oper_channel { |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID, |
| /* 32-bit unsigned value; indicates the connection/iface type likely to |
| * come on this channel (see enum qca_iface_type). |
| */ |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE, |
| /* 32-bit unsigned value; the frequency (MHz) of the probable channel */ |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX = |
| QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_gw_param_config - gateway param config |
| * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_INVALID: Invalid |
| * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_GW_MAC_ADDR: gateway mac addr |
| * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV4_ADDR: ipv4 addr |
| * @QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV6_ADDR: ipv6 addr |
| */ |
| enum qca_wlan_vendor_attr_gw_param_config { |
| QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_GW_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV4_ADDR, |
| QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_IPV6_ADDR, |
| QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_GW_PARAM_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum drv_dbs_capability - DBS capability |
| * @DRV_DBS_CAPABILITY_DISABLED: DBS disabled |
| * @DRV_DBS_CAPABILITY_1X1: 1x1 |
| * @DRV_DBS_CAPABILITY_2X2: 2x2 |
| */ |
| enum drv_dbs_capability { |
| DRV_DBS_CAPABILITY_DISABLED, /* not supported or disabled */ |
| DRV_DBS_CAPABILITY_1X1, |
| DRV_DBS_CAPABILITY_2X2, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease |
| * |
| * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB. |
| */ |
| enum qca_vendor_attr_txpower_decr_db { |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID, |
| /* |
| * 8-bit unsigned value to indicate the reduction of TX power in dB for |
| * a virtual interface. |
| */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX = |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_vendor_attr_ota_test - Enable OTA test |
| * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID: invalid value |
| * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable OTA test |
| * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX: max |
| */ |
| enum qca_vendor_attr_ota_test { |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID, |
| /* 8-bit unsigned value to indicate if OTA test is enabled */ |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX = |
| QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1 |
| }; |
| |
| /** enum qca_vendor_attr_txpower_scale - vendor sub commands index |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID: invalid value |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST: last value |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX: max value |
| */ |
| enum qca_vendor_attr_txpower_scale { |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID, |
| /* 8-bit unsigned value to indicate the scaling of tx power */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX = |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_vendor_attr_txpower_scale_decr_db - vendor sub commands index |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_INVALID: invalid value |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB: scaling value |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST: last value |
| * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_MAX: max value |
| */ |
| enum qca_vendor_attr_txpower_scale_decr_db { |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_INVALID, |
| /* 8-bit unsigned value to indicate the scaling of tx power */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_MAX = |
| QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_DECR_DB_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum dfs_mode - state of DFS mode |
| * @DFS_MODE_NONE: DFS mode attribute is none |
| * @DFS_MODE_ENABLE: DFS mode is enabled |
| * @DFS_MODE_DISABLE: DFS mode is disabled |
| * @DFS_MODE_DEPRIORITIZE: Deprioritize DFS channels in scanning |
| */ |
| enum dfs_mode { |
| DFS_MODE_NONE, |
| DFS_MODE_ENABLE, |
| DFS_MODE_DISABLE, |
| DFS_MODE_DEPRIORITIZE |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_acs_config - Config params for ACS |
| * @QCA_WLAN_VENDOR_ATTR_ACS_MODE_INVALID: Invalid |
| * @QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE: Dfs mode for ACS |
| * QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT: channel_hint for ACS |
| * QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST: after_last |
| * QCA_WLAN_VENDOR_ATTR_ACS_DFS_MAX: max attribute |
| */ |
| enum qca_wlan_vendor_attr_acs_config { |
| QCA_WLAN_VENDOR_ATTR_ACS_MODE_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE, |
| QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT, |
| |
| QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ACS_DFS_MAX = |
| QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST - 1, |
| |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability |
| */ |
| enum qca_wlan_vendor_attr_get_hw_capability { |
| QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID, |
| /* |
| * Antenna isolation |
| * An attribute used in the response. |
| * The content of this attribute is encoded in a byte array. Each byte |
| * value is an antenna isolation value. The array length is the number |
| * of antennas. |
| */ |
| QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION, |
| /* |
| * Request HW capability |
| * An attribute used in the request. |
| * The content of this attribute is a u32 array for one or more of |
| * hardware capabilities (attribute IDs) that are being requested. Each |
| * u32 value has a value from this |
| * enum qca_wlan_vendor_attr_get_hw_capability |
| * identifying which capabilities are requested. |
| */ |
| QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX = |
| QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sta_connect_roam_policy_config - |
| * config params for sta roam policy |
| * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_INVALID: Invalid |
| * @QCA_WLAN_VENDOR_ATTR_STA_DFS_MODE: If sta should skip Dfs channels |
| * @QCA_WLAN_VENDOR_ATTR_STA_SKIP_UNSAFE_CHANNEL: |
| * If sta should skip unsafe channels or not in scanning |
| * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_LAST: |
| * @QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_MAX: max attribute |
| */ |
| enum qca_wlan_vendor_attr_sta_connect_roam_policy_config { |
| QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_STA_DFS_MODE, |
| QCA_WLAN_VENDOR_ATTR_STA_SKIP_UNSAFE_CHANNEL, |
| |
| QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_MAX = |
| QCA_WLAN_VENDOR_ATTR_STA_CONNECT_ROAM_POLICY_AFTER_LAST - 1, |
| }; |
| |
| /* Attributes for FTM commands and events */ |
| |
| /** |
| * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See |
| * enum qca_wlan_vendor_attr_loc_capa_flags. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number |
| * of measurement sessions that can run concurrently. |
| * Default is one session (no session concurrency). |
| * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique |
| * peers that are supported in running sessions. For example, |
| * if the value is 8 and maximum number of sessions is 2, you can |
| * have one session with 8 unique peers, or 2 sessions with 4 unique |
| * peers each, and so on. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number |
| * of bursts per peer, as an exponent (2^value). Default is 0, |
| * meaning no multi-burst support. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number |
| * of measurement exchanges allowed in a single burst. |
| * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement |
| * types. A bit mask (unsigned 32 bit value), each bit corresponds |
| * to an AOA type as defined by enum qca_vendor_attr_aoa_type. |
| */ |
| enum qca_wlan_vendor_attr_loc_capa { |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS, |
| QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS, |
| QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS, |
| QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP, |
| QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST, |
| QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX = |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver |
| * can be configured as an FTM responder (for example, an AP that |
| * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER |
| * will be supported if set. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver |
| * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION |
| * will be supported if set. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder |
| * supports immediate (ASAP) response. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone |
| * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports |
| * requesting AOA measurements as part of an FTM session. |
| */ |
| enum qca_wlan_vendor_attr_loc_capa_flags { |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3, |
| QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_sap_config - config params for sap configuration |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID: invalid |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL: Channel on which SAP should start |
| * @QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST: List of frequencies on |
| * which AP is expected to operate. This is irrespective of ACS configuration. |
| * This list is a priority based one and is looked for before the AP is created |
| * to ensure the best concurrency sessions (avoid MCC and use DBS/SCC) co-exist |
| * in the system. |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST: after last |
| * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX: max attribute |
| */ |
| enum qca_wlan_vendor_attr_sap_config { |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_info: Information about |
| * a single peer in a measurement session. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related |
| * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of |
| * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0 |
| * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for |
| * list of supported attributes. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for |
| * secure measurement. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA |
| * measurement every <value> bursts. If 0 or not specified, |
| * AOA measurements will be disabled for this peer. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where |
| * the measurement frames are exchanged. Optional; if not |
| * specified, try to locate the peer in the kernel scan |
| * results cache and use frequency from there. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_info { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX = |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags, |
| * per-peer |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request |
| * immediate (ASAP) response from peer. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request |
| * LCI report from peer. The LCI report includes the absolute |
| * location of the peer in "official" coordinates (similar to GPS). |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request |
| * Location civic report from peer. The LCR includes the location |
| * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0, |
| * 11.24.6.7 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set, |
| * request a secure measurement. |
| * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_meas_flags { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements |
| * to perform in a single burst. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to |
| * perform, specified as an exponent (2^value). |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst |
| * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts, |
| * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must |
| * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION. |
| */ |
| enum qca_wlan_vendor_attr_ftm_meas_param { |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported |
| * peer. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement |
| * request for this peer. |
| * See enum qca_wlan_vendor_attr_ftm_peer_result_status. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related |
| * to measurement results for this peer. |
| * See enum qca_wlan_vendor_attr_ftm_peer_result_flags. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when |
| * request failed and peer requested not to send an additional request |
| * for this number of seconds. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received |
| * from peer. In the format specified by IEEE P802.11-REVmc/D7.0, |
| * 9.4.2.22.10. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when |
| * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0, |
| * 9.4.2.22.13. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer |
| * overridden some measurement request parameters. See |
| * enum qca_wlan_vendor_attr_ftm_meas_param. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement |
| * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement |
| * results. Each entry is a nested attribute defined |
| * by enum qca_wlan_vendor_attr_ftm_meas. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_result { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX = |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_result_status |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results |
| * will be provided. Peer may have overridden some measurement parameters, |
| * in which case overridden parameters will be report by |
| * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable |
| * of performing the measurement request. No more results will be sent |
| * for this peer in this session. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request |
| * failed, and requested not to send an additional request for number |
| * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS |
| * attribute. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation |
| * failed. Request was not sent over the air. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_result_status { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED, |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags |
| * for measurement result, per-peer |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set, |
| * measurement completed for this peer. No more results will be reported |
| * for this peer in this session. |
| */ |
| enum qca_wlan_vendor_attr_ftm_peer_result_flags { |
| QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_loc_session_status: Session completion status code |
| * |
| * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed |
| * successfully. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted |
| * by request. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request |
| * was invalid and was not started. |
| * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error |
| * and did not complete normally (for example out of resources). |
| */ |
| enum qca_vendor_attr_loc_session_status { |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK, |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED, |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID, |
| QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as |
| * recorded by responder, in picoseconds. |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at |
| * initiator, in picoseconds. |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by |
| * initiator, in picoseconds. |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at |
| * responder, in picoseconds. |
| * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded |
| * during this measurement exchange. Optional and will be provided if |
| * the hardware can measure it. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by |
| * responder. Not always provided. |
| * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by |
| * responder. Not always provided. |
| * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by |
| * initiator. Not always provided. |
| * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by |
| * initiator. Not always provided. |
| * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. |
| * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding. |
| */ |
| enum qca_wlan_vendor_attr_ftm_meas { |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX = |
| QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_p2p_listen_offload - vendor sub commands index |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID: invalid value |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL: |
| * A 32-bit unsigned value; the P2P listen frequency (MHz); must be one |
| * of the social channels. |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD: listen offload period |
| * A 32-bit unsigned value; the P2P listen offload period (ms). |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL: |
| * A 32-bit unsigned value; the P2P listen interval duration (ms). |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT: |
| * A 32-bit unsigned value; number of interval times the Firmware needs |
| * to run the offloaded P2P listen operation before it stops. |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES: device types |
| * An array of unsigned 8-bit characters; vendor information elements. |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE: vendor IEs |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG: control flag for FW |
| * A 32-bit unsigned value; a control flag to indicate whether listen |
| * results need to be flushed to wpa_supplicant. |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON: offload stop reason |
| * A 8-bit unsigned value; reason code for P2P listen offload stop |
| * event. |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST: last value |
| * @QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX: max value |
| */ |
| enum qca_wlan_vendor_attr_p2p_listen_offload { |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON, |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX = |
| QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_drv_info - WLAN driver info |
| * @QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID: Invalid |
| * @QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE: Maximum Message size info |
| * between Firmware & Host. |
| */ |
| enum qca_wlan_vendor_drv_info { |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type |
| * |
| * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest |
| * CIR (channel impulse response) path for each antenna. |
| * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude |
| * of the strongest CIR path for each antenna. |
| */ |
| enum qca_wlan_vendor_attr_aoa_type { |
| QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE, |
| QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP, |
| QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_encryption_test - Attributes to |
| * validate encryption engine |
| * |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute. |
| * This will be included if the request is for decryption; if not included, |
| * the request is treated as a request for encryption by default. |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value |
| * indicating the key cipher suite. Takes same values as |
| * NL80211_ATTR_KEY_CIPHER. |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value |
| * Key Id to be used for encryption |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values. |
| * Key (TK) to be used for encryption/decryption |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values. |
| * Packet number to be specified for encryption/decryption |
| * 6 bytes for TKIP/CCMP/GCMP. |
| * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values |
| * representing the 802.11 packet (header + payload + FCS) that |
| * needs to be encrypted/decrypted. |
| * Encrypted/decrypted response from the driver will also be sent |
| * to userspace with the same attribute. |
| */ |
| enum qca_wlan_vendor_attr_encryption_test { |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX = |
| QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of |
| * sector for DMG RF sector operations. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector |
| */ |
| enum qca_wlan_vendor_attr_dmg_rf_sector_type { |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_fw_state - State of firmware |
| * |
| * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR: FW is in bad state |
| * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE: FW is active |
| */ |
| enum qca_wlan_vendor_attr_fw_state { |
| QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR, |
| QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE, |
| QCA_WLAN_VENDOR_ATTR_FW_STATE_MAX |
| }; |
| |
| /** |
| * BRP antenna limit mode |
| * |
| * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force |
| * antenna limit, BRP will be performed as usual. |
| * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal |
| * antennas limit. the hardware may use less antennas than the |
| * maximum limit. |
| * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will |
| * use exactly the specified number of antennas for BRP. |
| */ |
| enum qca_wlan_vendor_attr_brp_ant_limit_mode { |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE, |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE, |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE, |
| QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for |
| * DMG RF sector configuration for a single RF module. |
| * The values are defined in a compact way which closely matches |
| * the way it is stored in HW registers. |
| * The configuration provides values for 32 antennas and 8 distribution |
| * amplifiers, and together describes the characteristics of the RF |
| * sector - such as a beam in some direction with some gain. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index |
| * of RF module for this configuration. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge |
| * amplifier gain index. Unsigned 32 bit number containing |
| * bits for all 32 antennas. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge |
| * amplifier gain index. Unsigned 32 bit number containing |
| * bits for all 32 antennas. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge |
| * amplifier gain index. Unsigned 32 bit number containing |
| * bits for all 32 antennas. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values |
| * for first 16 antennas, 2 bits per antenna. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values |
| * for last 16 antennas, 2 bits per antenna. |
| * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains |
| * DTYPE values (3 bits) for each distribution amplifier, followed |
| * by X16 switch bits for each distribution amplifier. There are |
| * total of 8 distribution amplifiers. |
| */ |
| enum qca_wlan_vendor_attr_dmg_rf_sector_cfg { |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX = |
| QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for |
| * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS configuration to the host driver. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger |
| * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode |
| * represents the different TDLS trigger modes. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within |
| * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number |
| * of packets shall meet the criteria for implicit TDLS setup. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx |
| * packets within a duration. |
| * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD to initiate |
| * a TDLS setup. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to inititate |
| * a TDLS Discovery to the Peer. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of |
| * discovery attempts to know the TDLS capability of the peer. A peer is |
| * marked as TDLS not capable if there is no response for all the attempts. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32) |
| * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD |
| * number of TX / RX frames meet the criteria for TDLS teardown. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number |
| * (u32) of Tx/Rx packets within a duration |
| * CA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold |
| * corresponding to the RSSI of the peer below which a TDLS |
| * setup is triggered. |
| * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold |
| * corresponding to the RSSI of the peer above which |
| * a TDLS teardown is triggered. |
| */ |
| enum qca_wlan_vendor_attr_tdls_configuration { |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1, |
| |
| /* Attributes configuring the TDLS Implicit Trigger */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in |
| * the driver. |
| * |
| * The following are the different values for |
| * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE. |
| * |
| * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to |
| * initiate/teardown the TDLS connection to a respective peer comes |
| * from the user space. wpa_supplicant provides the commands |
| * TDLS_SETUP, TDLS_TEARDOWN, TDLS_DISCOVER to do this. |
| * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS |
| * setup/teardown to the eligible peer once the configured criteria |
| * (such as TX/RX threshold, RSSI) is met. The attributes |
| * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to |
| * the different configuration criteria for the TDLS trigger from the |
| * host driver. |
| * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger |
| * the TDLS setup / teardown through the implicit mode, only to the |
| * configured MAC addresses(wpa_supplicant, with tdls_external_control = 1, |
| * configures the MAC address through TDLS_SETUP/TDLS_TEARDOWN commands). |
| * External mode works on top of the implicit mode, thus the host Driver |
| * is expected to be configured in TDLS Implicit mode too to operate in |
| * External mode. Configuring External mode alone without Implicit |
| * mode is invalid. |
| * |
| * All the above implementations work as expected only when the host driver |
| * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - |
| * representing that the TDLS message exchange is not internal to the host |
| * driver, but depends on wpa_supplicant to do the message exchange. |
| */ |
| enum qca_wlan_vendor_tdls_trigger_mode { |
| QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0, |
| QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1, |
| QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4 |
| * that is hard-coded in the Board Data File (BDF). |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any |
| * source of SAR power limits, thereby disabling the SAR power |
| * limit feature. |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power |
| * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power |
| * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. |
| * |
| * This enumerates the valid set of values that may be supplied for |
| * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of |
| * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in |
| * the response to an instance of the |
| * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. |
| */ |
| enum qca_vendor_attr_sar_limits_selections { |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_sar_limits_spec_modulations - |
| * SAR limits specification modulation |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK - |
| * CCK modulation |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM - |
| * OFDM modulation |
| * |
| * This enumerates the valid set of values that may be supplied for |
| * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an |
| * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an |
| * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor |
| * command or in the response to an instance of the |
| * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. |
| */ |
| enum qca_vendor_attr_sar_limits_spec_modulations { |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1, |
| }; |
| |
| /** |
| * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to |
| * select which SAR power limit table should be used. Valid |
| * values are enumerated in enum |
| * %qca_vendor_attr_sar_limits_selections. The existing SAR |
| * power limit selection is unchanged if this attribute is not |
| * present. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value |
| * which specifies the number of SAR power limit specifications |
| * which will follow. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power |
| * limit specifications. The number of specifications is |
| * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each |
| * specification contains a set of |
| * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A |
| * specification is uniquely identified by the attributes |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND, |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always |
| * contains as a payload the attribute |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT. |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX. |
| * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is |
| * needed based upon the value of |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to |
| * indicate for which band this specification applies. Valid |
| * values are enumerated in enum %nl80211_band (although not all |
| * bands may be supported by a given device). If the attribute is |
| * not supplied then the specification will be applied to all |
| * supported bands. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value |
| * to indicate for which antenna chain this specification |
| * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the |
| * attribute is not supplied then the specification will be |
| * applied to all chains. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32) |
| * value to indicate for which modulation scheme this |
| * specification applies. Valid values are enumerated in enum |
| * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute |
| * is not supplied then the specification will be applied to all |
| * modulation schemes. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32) |
| * value to specify the actual power limit value in units of 0.5 |
| * dBm (i.e., a value of 11 represents 5.5 dBm). |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32) |
| * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles. |
| * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is |
| * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0. |
| * |
| * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS |
| * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS. |
| */ |
| enum qca_vendor_attr_sar_limits { |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8, |
| |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX = |
| QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring |
| * offload which is an extension for LL_STATS. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms. |
| * If MAC counters do not exceed the threshold, FW will report monitored |
| * link layer counters periodically as this setting. The first report is |
| * always triggered by this timer. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99). |
| * For each MAC layer counter, FW holds two copies. One is the current value. |
| * The other is the last report. Once a current counter's increment is larger |
| * than the threshold, FW will indicate that counter to host even if the |
| * monitoring timer does not expire. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same |
| * failure code. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code |
| * 1: TX packet discarded |
| * 2: No ACK |
| * 3: Postpone |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold. |
| * Threshold for all monitored parameters. If per counter dedicated threshold |
| * is not enabled, this threshold will take effect. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this |
| * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters |
| * Bit0: TX counter unit in MSDU |
| * Bit1: TX counter unit in MPDU |
| * Bit2: TX counter unit in PPDU |
| * Bit3: TX counter unit in byte |
| * Bit4: Dropped MSDUs |
| * Bit5: Dropped Bytes |
| * Bit6: MPDU retry counter |
| * Bit7: MPDU failure counter |
| * Bit8: PPDU failure counter |
| * Bit9: MPDU aggregation counter |
| * Bit10: MCS counter for ACKed MPDUs |
| * Bit11: MCS counter for Failed MPDUs |
| * Bit12: TX Delay counter |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters |
| * Bit0: MAC RX counter unit in MPDU |
| * Bit1: MAC RX counter unit in byte |
| * Bit2: PHY RX counter unit in PPDU |
| * Bit3: PHY RX counter unit in byte |
| * Bit4: Disorder counter |
| * Bit5: Retry counter |
| * Bit6: Duplication counter |
| * Bit7: Discard counter |
| * Bit8: MPDU aggregation size counter |
| * Bit9: MCS counter |
| * Bit10: Peer STA power state change (wake to sleep) counter |
| * Bit11: Peer STA power save counter, total time in PS mode |
| * Bit12: Probe request counter |
| * Bit13: Other management frames counter |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA |
| * Bit0: Idle time |
| * Bit1: TX time |
| * Bit2: time RX in current bss |
| * Bit3: Out of current bss time |
| * Bit4: Wireless medium busy time |
| * Bit5: RX in bad condition time |
| * Bit6: TX in bad condition time |
| * Bit7: time wlan card not available |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal |
| * Bit0: Per channel SNR counter |
| * Bit1: Per channel noise floor counter |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM: |
| * aggregation stats buffer length |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats |
| * buffer for ACKed MPDUs. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats |
| * buffer for failed MPDUs. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE: |
| * length of delay stats array. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets |
| * flagged as retransmissions |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets |
| * flagged as duplicated |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX |
| * packets discarded |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation |
| * stats buffer. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs |
| * stats buffer. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe |
| * requests received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt |
| * frames received |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time |
| * there is no TX, nor RX, nor interference. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time |
| * transmitting packets. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time |
| * for receiving. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time |
| * interference detected. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time |
| * receiving packets with errors. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time |
| * TX no-ACK. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time |
| * the chip is unable to work in normal conditions. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time |
| * receiving packets in current BSS. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time |
| * receiving packets not in current BSS. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL: |
| * This is a container for per antenna signal stats. |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon |
| * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon |
| */ |
| enum qca_wlan_vendor_attr_ll_stats_ext { |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0, |
| |
| /* Attributes for configurations */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD, |
| |
| /* Peer STA power state change */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG, |
| |
| /* TX failure event */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS, |
| |
| /* MAC counters */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER, |
| |
| /* Sub-attributes for PEER_AC_TX */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY, |
| |
| /* Sub-attributes for PEER_AC_RX */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT, |
| |
| /* Sub-attributes for CCA_BSS */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL, |
| |
| /* sub-attribute for BSS_RX_TIME */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME, |
| |
| /* Sub-attributes for PEER_SIGNAL */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF, |
| |
| /* Sub-attributes for IFACE_BSS */ |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON, |
| |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST, |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX = |
| QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1 |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_external_acs_channels: attribute to vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carry a list of channels |
| * in priority order as decided after acs operation in userspace. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON: One of reason code from |
| * qca_wlan_vendor_acs_select_reason. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_COUNT: Number of channels in |
| * this list |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST: Array of nested values |
| * for each channel with following attributes: |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY: Primary channel (u8) |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY: Secondary channel (u8) |
| * required only for 160 / 80 + 80 |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0: VHT seg0 channel (u8) |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1: VHT seg1 channel (u8) |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH:channel width (u8) |
| */ |
| enum qca_wlan_vendor_attr_external_acs_channels { |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0, |
| |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX = |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1 |
| }; |
| |
| /** |
| * qca_wlan_vendor_acs_select_reason: This represents the different reasons why |
| * the ACS has to be triggered. These parameters are used by |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and |
| * QCA_NL80211_VENDOR_SUBCMD_ACS_SET_CHANNELS |
| * @QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT: Represents the reason that the |
| * ACS triggered during the AP start |
| * @QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS: Represents the reason that |
| * DFS found with current channel |
| * @QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX: Represents the reason that |
| * LTE CO-Exist in current band |
| */ |
| enum qca_wlan_vendor_acs_select_reason { |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT, |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS, |
| QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX, |
| }; |
| |
| /** |
| * enum qca_wlan_gpio_attr - Parameters for GPIO configuration |
| */ |
| enum qca_wlan_gpio_attr { |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0, |
| /* Unsigned 32-bit attribute for GPIO command */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND, |
| /* Unsigned 32-bit attribute for GPIO PIN number to configure */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM, |
| /* Unsigned 32-bit attribute for GPIO value to configure */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE, |
| /* Unsigned 32-bit attribute for GPIO pull type */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE, |
| /* Unsigned 32-bit attribute for GPIO interrupt mode */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST, |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX = |
| QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_set_qdepth_thresh_attr - Parameters for setting |
| * MSDUQ depth threshold per peer per tid in the target |
| * |
| * Associated Vendor Command: |
| * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH |
| */ |
| enum qca_wlan_set_qdepth_thresh_attr { |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0, |
| /* 6-byte MAC address */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR, |
| /* Unsigned 32-bit attribute for holding the TID */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID, |
| /* Unsigned 32-bit attribute for holding the update mask |
| * bit 0 - Update high priority msdu qdepth threshold |
| * bit 1 - Update low priority msdu qdepth threshold |
| * bit 2 - Update UDP msdu qdepth threshold |
| * bit 3 - Update Non UDP msdu qdepth threshold |
| * rest of bits are reserved |
| */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK, |
| /* Unsigned 32-bit attribute for holding the threshold value */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST, |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX = |
| QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_external_acs_policy: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the |
| * external ACS policies to select the channels w.r.t. the PCL weights. |
| * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and |
| * their PCL weights.) |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to |
| * select a channel with non-zero PCL weight. |
| * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a |
| * channel with non-zero PCL weight. |
| * |
| */ |
| enum qca_wlan_vendor_attr_external_acs_policy { |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED, |
| QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters |
| */ |
| enum qca_wlan_vendor_attr_spectral_scan { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0, |
| /* |
| * Number of times the chip enters spectral scan mode before |
| * deactivating spectral scans. When set to 0, chip will enter spectral |
| * scan mode continuously. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1, |
| /* |
| * Spectral scan period. Period increment resolution is 256*Tclk, |
| * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2, |
| /* Spectral scan priority. u32 attribute. */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3, |
| /* Number of FFT data points to compute. u32 attribute. */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4, |
| /* |
| * Enable targeted gain change before starting the spectral scan FFT. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5, |
| /* Restart a queued spectral scan. u32 attribute. */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6, |
| /* |
| * Noise floor reference number for the calculation of bin power. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7, |
| /* |
| * Disallow spectral scan triggers after TX/RX packets by setting |
| * this delay value to roughly SIFS time period or greater. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8, |
| /* |
| * Number of strong bins (inclusive) per sub-channel, below |
| * which a signal is declared a narrow band tone. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9, |
| /* |
| * Specify the threshold over which a bin is declared strong (for |
| * scan bandwidth analysis). u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10, |
| /* Spectral scan report mode. u32 attribute. */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11, |
| /* |
| * RSSI report mode, if the ADC RSSI is below |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR, |
| * then FFTs will not trigger, but timestamps and summaries get |
| * reported. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12, |
| /* |
| * ADC RSSI must be greater than or equal to this threshold (signed dB) |
| * to ensure spectral scan reporting with normal error code. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13, |
| /* |
| * Format of frequency bin magnitude for spectral scan triggered FFTs: |
| * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)). |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14, |
| /* |
| * Format of FFT report to software for spectral scan triggered FFTs. |
| * 0: No FFT report (only spectral scan summary report) |
| * 1: 2-dword summary of metrics for each completed FFT + spectral scan |
| * report |
| * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled |
| * bins (in-band) per FFT + spectral scan summary report |
| * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled |
| * bins (all) per FFT + spectral scan summary report |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15, |
| /* |
| * Number of LSBs to shift out in order to scale the FFT bins. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16, |
| /* |
| * Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes |
| * in dBm power. u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17, |
| /* |
| * Per chain enable mask to select input ADC for search FFT. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18, |
| /* |
| * An unsigned 64-bit integer provided by host driver to identify the |
| * spectral scan request. This attribute is included in the scan |
| * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START |
| * and used as an attribute in |
| * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the |
| * specific scan to be stopped. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19, |
| /* Skip interval for FFT reports. u32 attribute */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20, |
| /* Set to report only one set of FFT results. |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21, |
| /* Debug level for spectral module in driver. |
| * 0 : Verbosity level 0 |
| * 1 : Verbosity level 1 |
| * 2 : Verbosity level 2 |
| * 3 : Matched filterID display |
| * 4 : One time dump of FFT report |
| * u32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22, |
| /* Type of spectral scan request. u32 attribute. |
| * It uses values defined in enum |
| * qca_wlan_vendor_attr_spectral_scan_request_type. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS. |
| */ |
| enum qca_wlan_vendor_attr_spectral_diag_stats { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0, |
| /* Number of spectral TLV signature mismatches. |
| * u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1, |
| /* Number of spectral phyerror events with insufficient length when |
| * parsing for secondary 80 search FFT report. u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2, |
| /* Number of spectral phyerror events without secondary 80 |
| * search FFT report. u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3, |
| /* Number of spectral phyerror events with vht operation segment 1 id |
| * mismatches in search fft report. u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4, |
| /* Number of spectral phyerror events with vht operation segment 2 id |
| * mismatches in search fft report. u64 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5, |
| |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX = |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. |
| */ |
| enum qca_wlan_vendor_attr_spectral_cap { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0, |
| /* Flag attribute to indicate phydiag capability */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1, |
| /* Flag attribute to indicate radar detection capability */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2, |
| /* Flag attribute to indicate spectral capability */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3, |
| /* Flag attribute to indicate advanced spectral capability */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4, |
| /* Spectral hardware generation. u32 attribute. |
| * It uses values defined in enum |
| * qca_wlan_vendor_spectral_scan_cap_hw_gen. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5, |
| /* Spectral bin scaling formula ID. u16 attribute. |
| * It uses values defined in enum |
| * qca_wlan_vendor_spectral_scan_cap_formula_id. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID = 6, |
| /* Spectral bin scaling param - low level offset. |
| * s16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_LOW_LEVEL_OFFSET = 7, |
| /* Spectral bin scaling param - high level offset. |
| * s16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HIGH_LEVEL_OFFSET = 8, |
| /* Spectral bin scaling param - RSSI threshold. |
| * s16 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RSSI_THR = 9, |
| /* Spectral bin scaling param - default AGC max gain. |
| * u8 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN = 10, |
| |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX = |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. |
| */ |
| enum qca_wlan_vendor_attr_spectral_scan_status { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0, |
| /* Flag attribute to indicate whether spectral scan is enabled */ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1, |
| /* Flag attribute to indicate whether spectral scan is in progress*/ |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2, |
| |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX = |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_config_latency_level - Level for |
| * wlan latency module. |
| * |
| * There will be various of Wi-Fi functionality like scan/roaming/adaptive |
| * power saving which would causing data exchange out of service, this |
| * would be a big impact on latency. For latency sensitive applications over |
| * Wi-Fi are intolerant to such operations and thus would configure them |
| * to meet their respective needs. It is well understood by such applications |
| * that altering the default behavior would degrade the Wi-Fi functionality |
| * w.r.t the above pointed WLAN operations. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL: |
| * Default WLAN operation level which throughput orientated. |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE: |
| * Use moderate level to improve latency by limit scan duration. |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW: |
| * Use low latency level to benifit application like concurrent |
| * downloading or video streaming via constraint scan/adaptive PS. |
| * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW: |
| * Use ultra low latency level to benefit for gaming/voice |
| * application via constraint scan/roaming/adaptive PS. |
| */ |
| enum qca_wlan_vendor_attr_config_latency_level { |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = 2, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX = |
| QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the |
| * spectral scan request types. |
| * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to |
| * set the spectral parameters and start scan. |
| * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to |
| * only set the spectral parameters. |
| * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to |
| * only start the spectral scan. |
| */ |
| enum qca_wlan_vendor_attr_spectral_scan_request_type { |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN, |
| QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG, |
| }; |
| |
| /** |
| * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the |
| * spectral hardware generation. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1 |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2 |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3 |
| */ |
| enum qca_wlan_vendor_spectral_scan_cap_hw_gen { |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2, |
| }; |
| |
| /** |
| * qca_wlan_vendor_spectral_scan_cap_formula_id: Attribute values for |
| * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID in the vendor subcmd |
| * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the |
| * Spectral bin scaling formula ID. |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING: No scaling |
| * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED: AGC gain |
| * and RSSI threshold based formula. |
| */ |
| enum qca_wlan_vendor_spectral_scan_cap_formula_id { |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING = 0, |
| QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED = 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative |
| * RF Operating Parameter (RROP) information is available, and if so, at which |
| * point in the application-driver interaction sequence it can be retrieved by |
| * the application from the driver. This point may vary by architecture and |
| * other factors. This is a u16 value. |
| */ |
| enum qca_wlan_vendor_attr_rropavail_info { |
| /* RROP information is unavailable. */ |
| QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE, |
| /* RROP information is available and the application can retrieve the |
| * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS |
| * event from the driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START, |
| /* RROP information is available only after a vendor specific scan |
| * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has |
| * successfully completed. The application can retrieve the information |
| * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from |
| * the driver. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific |
| * Representative RF Operating Parameter (RROP) information. It is sent for the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is |
| * intended for use by external Auto Channel Selection applications. It provides |
| * guidance values for some RF parameters that are used by the system during |
| * operation. These values could vary by channel, band, radio, and so on. |
| */ |
| enum qca_wlan_vendor_attr_rrop_info { |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0, |
| |
| /* Representative Tx Power List (RTPL) which has an array of nested |
| * values as per attributes in enum qca_wlan_vendor_attr_rtplinst. |
| */ |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1, |
| |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1 |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list |
| * entry instances in the Representative Tx Power List (RTPL). It provides |
| * simplified power values intended for helping external Auto channel Selection |
| * applications compare potential Tx power performance between channels, other |
| * operating conditions remaining identical. These values are not necessarily |
| * the actual Tx power values that will be used by the system. They are also not |
| * necessarily the max or average values that will be used. Instead, they are |
| * relative, summarized keys for algorithmic use computed by the driver or |
| * underlying firmware considering a number of vendor specific factors. |
| */ |
| enum qca_wlan_vendor_attr_rtplinst { |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0, |
| |
| /* Primary channel number (u8) */ |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1, |
| /* Representative Tx power in dBm (s32) with emphasis on throughput. */ |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2, |
| /* Representative Tx power in dBm (s32) with emphasis on range. */ |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3, |
| |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX = |
| QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mac - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MAC_INFO: MAC mode info list which has an |
| * array of nested values as per attributes in |
| * enum qca_wlan_vendor_attr_mac_mode_info. |
| */ |
| enum qca_wlan_vendor_attr_mac { |
| QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MAC_MAX = |
| QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected |
| * WiFi netdev interface on a respective MAC. Used by the attribute |
| * QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_ID: Wi-Fi Netdev's interface id(u32). |
| * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ: Associated frequency in MHz of |
| * the connected Wi-Fi interface(u32). |
| */ |
| enum qca_wlan_vendor_attr_mac_iface_info { |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1, |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information. |
| * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the |
| * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID: Hardware MAC ID associated for the |
| * MAC (u32) |
| * @QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND: Band supported by the respective MAC |
| * at a given point. This is a u32 bitmask of BIT(NL80211_BAND_*) as described |
| * in enum nl80211_band. |
| * @QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO: Refers to list of WLAN net dev |
| * interfaces associated with this MAC. Represented by enum |
| * qca_wlan_vendor_attr_mac_iface_info. |
| */ |
| enum qca_wlan_vendor_attr_mac_info { |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1, |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2, |
| QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX = |
| QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1, |
| |
| }; |
| |
| #if !(defined (SUPPORT_WDEV_CFG80211_VENDOR_EVENT_ALLOC)) && \ |
| (LINUX_VERSION_CODE < KERNEL_VERSION(4, 1, 0)) && \ |
| !(defined(WITH_BACKPORTS)) |
| |
| static inline struct sk_buff * |
| backported_cfg80211_vendor_event_alloc(struct wiphy *wiphy, |
| struct wireless_dev *wdev, |
| int approxlen, |
| int event_idx, gfp_t gfp) |
| { |
| struct sk_buff *skb; |
| |
| skb = cfg80211_vendor_event_alloc(wiphy, approxlen, event_idx, gfp); |
| |
| if (skb && wdev) { |
| struct nlattr *attr; |
| u32 ifindex = wdev->netdev->ifindex; |
| |
| nla_nest_cancel(skb, ((void **)skb->cb)[2]); |
| if (nla_put_u32(skb, NL80211_ATTR_IFINDEX, ifindex)) |
| goto nla_fail; |
| |
| attr = nla_nest_start(skb, NL80211_ATTR_VENDOR_DATA); |
| ((void **)skb->cb)[2] = attr; |
| } |
| |
| return skb; |
| |
| nla_fail: |
| kfree_skb(skb); |
| |
| return NULL; |
| } |
| #define cfg80211_vendor_event_alloc backported_cfg80211_vendor_event_alloc |
| #endif |
| |
| /** |
| * enum he_fragmentation_val - HE fragmentation support values |
| * Indicates level of dynamic fragmentation that is supported by |
| * a STA as a recipient. |
| * HE fragmentation values are defined as per 11ax spec and are used in |
| * HE capability IE to advertise the support. These values are validated |
| * in the driver to check the device capability and advertised in the HE |
| * capability element. |
| * |
| * @HE_FRAG_DISABLE: no support for dynamic fragmentation |
| * @HE_FRAG_LEVEL1: support for dynamic fragments that are |
| * contained within an MPDU or S-MPDU, no support for dynamic fragments |
| * within an A-MPDU that is not an S-MPDU. |
| * @HE_FRAG_LEVEL2: support for dynamic fragments that are |
| * contained within an MPDU or S-MPDU and support for up to one dynamic |
| * fragment for each MSDU, each A-MSDU if supported by the recipient, and |
| * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an |
| * MPDU or S-MPDU. |
| * @HE_FRAG_LEVEL3: support for dynamic fragments that are |
| * contained within an MPDU or S-MPDU and support for multiple dynamic |
| * fragments for each MSDU and for each A-MSDU if supported by the |
| * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic |
| * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU. |
| */ |
| enum he_fragmentation_val { |
| HE_FRAG_DISABLE, |
| HE_FRAG_LEVEL1, |
| HE_FRAG_LEVEL2, |
| HE_FRAG_LEVEL3, |
| }; |
| |
| /** |
| * enum he_mcs_config - HE MCS support configuration |
| * |
| * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth. |
| * These values are used in driver to configure the HE MCS map to advertise |
| * Tx/Rx MCS map in HE capability and these values are applied for all the |
| * streams supported by the device. To configure MCS for different bandwidths, |
| * vendor command needs to be sent using this attribute with appropriate value. |
| * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS |
| * attribute with QCA_WLAN_VENDOR_ATTR_HE_80_MCS0_7. And to configure HE MCS |
| * for HE_160_MCS0_11 send this command using HE MCS config attribute with |
| * value QCA_WLAN_VENDOR_ATTR_HE_160_MCS0_11; |
| * |
| * @HE_80_MCS0_7: support for HE 80/40/20MHz MCS 0 to 7 |
| * @HE_80_MCS0_9: support for HE 80/40/20MHz MCS 0 to 9 |
| * @HE_80_MCS0_11: support for HE 80/40/20MHz MCS 0 to 11 |
| * @HE_160_MCS0_7: support for HE 160MHz MCS 0 to 7 |
| * @HE_160_MCS0_9: support for HE 160MHz MCS 0 to 9 |
| * @HE_160_MCS0_11: support for HE 160MHz MCS 0 to 11 |
| * @HE_80p80_MCS0_7: support for HE 80p80MHz MCS 0 to 7 |
| * @HE_80p80_MCS0_9: support for HE 80p80MHz MCS 0 to 9 |
| * @HE_80p80_MCS0_11: support for HE 80p80MHz MCS 0 to 11 |
| */ |
| enum he_mcs_config { |
| HE_80_MCS0_7 = 0, |
| HE_80_MCS0_9 = 1, |
| HE_80_MCS0_11 = 2, |
| HE_160_MCS0_7 = 4, |
| HE_160_MCS0_9 = 5, |
| HE_160_MCS0_11 = 6, |
| HE_80p80_MCS0_7 = 8, |
| HE_80p80_MCS0_9 = 9, |
| HE_80p80_MCS0_11 = 10, |
| }; |
| |
| /** |
| * enum qca_wlan_ba_session_config - BA session configuration |
| * |
| * Indicates the configuration values for BA session configuration attribute. |
| * |
| * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration. |
| * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID. |
| */ |
| enum qca_wlan_ba_session_config { |
| QCA_WLAN_ADD_BA = 1, |
| QCA_WLAN_DELETE_BA = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_ac_type - access category type |
| * |
| * Indicates the access category type value. |
| * |
| * @QCA_WLAN_AC_BE: BE access category |
| * @QCA_WLAN_AC_BK: BK access category |
| * @QCA_WLAN_AC_VI: VI access category |
| * @QCA_WLAN_AC_VO: VO access category |
| * @QCA_WLAN_AC_ALL: All ACs |
| */ |
| enum qca_wlan_ac_type { |
| QCA_WLAN_AC_BE = 0, |
| QCA_WLAN_AC_BK = 1, |
| QCA_WLAN_AC_VI = 2, |
| QCA_WLAN_AC_VO = 3, |
| QCA_WLAN_AC_ALL = 4, |
| }; |
| |
| /** |
| * enum qca_wlan_he_ltf_cfg - HE LTF configuration |
| * |
| * Indicates the HE LTF configuration value. |
| * |
| * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to |
| * the mandatory HE-LTF based on the GI setting |
| * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF |
| * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF |
| * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF |
| */ |
| enum qca_wlan_he_ltf_cfg { |
| QCA_WLAN_HE_LTF_AUTO = 0, |
| QCA_WLAN_HE_LTF_1X = 1, |
| QCA_WLAN_HE_LTF_2X = 2, |
| QCA_WLAN_HE_LTF_4X = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration |
| * |
| * Indicates the HE trigger frame MAC padding duration value. |
| * |
| * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to |
| * process the trigger frame. |
| * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for |
| * trigger frame. |
| * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for |
| * trigger frame. |
| */ |
| enum qca_wlan_he_mac_padding_dur { |
| QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0, |
| QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1, |
| QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration |
| * |
| * Indicates the HE Operating mode control channel width setting value. |
| * |
| * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz |
| * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz |
| * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz |
| * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz |
| */ |
| enum qca_wlan_he_om_ctrl_ch_bw { |
| QCA_WLAN_HE_OM_CTRL_BW_20M = 0, |
| QCA_WLAN_HE_OM_CTRL_BW_40M = 1, |
| QCA_WLAN_HE_OM_CTRL_BW_80M = 2, |
| QCA_WLAN_HE_OM_CTRL_BW_160M = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_he_omi_tx: Represents attributes for |
| * HE operating mode control transmit request. These attributes are |
| * sent as part of QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX and |
| * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS: Mandatory 8-bit unsigned value |
| * indicates the maximum number of spatial streams, NSS, that the STA |
| * supports in reception for PPDU bandwidths less than or equal to 80 MHz |
| * and is set to NSS - 1. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW: Mandatory 8-bit unsigned value |
| * indicates the operating channel width supported by the STA for both |
| * reception and transmission. Uses enum qca_wlan_he_om_ctrl_ch_bw values. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE: Mandatory 8-bit unsigned value |
| * indicates the all trigger based UL MU operations by the STA. |
| * 0 - UL MU operations are enabled by the STA. |
| * 1 - All triggered UL MU transmissions are suspended by the STA. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS: Mandatory 8-bit unsigned value |
| * indicates the maximum number of space-time streams, NSTS, that |
| * the STA supports in transmission and is set to NSTS - 1. |
| */ |
| enum qca_wlan_vendor_attr_he_omi_tx { |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS = 1, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW = 2, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE = 3, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_MAX = |
| QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST - 1, |
| }; |
| |
| /* Attributes for data used by |
| * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION |
| */ |
| enum qca_wlan_vendor_attr_wifi_test_config { |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0, |
| /* 8-bit unsigned value to configure the driver to enable/disable |
| * WMM feature. This attribute is used to configure testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1, |
| |
| /* 8-bit unsigned value to configure the driver to accept/reject |
| * the addba request from peer. This attribute is used to configure |
| * the testbed device. |
| * 1-accept addba, 0-reject addba |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2, |
| |
| /* 8-bit unsigned value to configure the driver to send or not to |
| * send the addba request to peer. |
| * This attribute is used to configure the testbed device. |
| * 1-send addba, 0-do not send addba |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3, |
| |
| /* 8-bit unsigned value to indicate the HE fragmentation support. |
| * Uses enum he_fragmentation_val values. |
| * This attribute is used to configure the testbed device to |
| * allow the advertised hardware capabilities to be downgraded |
| * for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4, |
| |
| /* 8-bit unsigned value to indicate the HE MCS support. |
| * Uses enum he_mcs_config values. |
| * This attribute is used to configure the testbed device to |
| * allow the advertised hardware capabilities to be downgraded |
| * for testing purposes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5, |
| |
| /* 8-bit unsigned value to configure the driver to allow or not to |
| * allow the connection with WEP/TKIP in HT/VHT/HE modes. |
| * This attribute is used to configure the testbed device. |
| * 1-allow wep/tkip in HT/VHT/HE, 0-do not allow wep/tkip |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6, |
| |
| /* 8-bit unsigned value to configure the driver to add a |
| * new BA session or delete the existing BA session for |
| * given TID. ADDBA command uses the buffer size and tid |
| * configuration if user specifies the values else default |
| * value for buffer size is used for all tids if the tid |
| * also not specified. For DEL_BA command TID value is |
| * required to process the command. |
| * Uses enum qca_wlan_ba_session_config values. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7, |
| |
| /* 16-bit unsigned value to configure the buffer size in addba |
| * request and response frames. |
| * This attribute is used to configure the testbed device. |
| * The range of the value is 0 to 256. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8, |
| |
| /* 8-bit unsigned value to configure the buffer size in addba |
| * request and response frames. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9, |
| |
| /* 8-bit unsigned value to configure the no ack policy. |
| * To configure no ack policy, access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| * 1 - enable no ack, 0 - disable no ack |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10, |
| |
| /* 8-bit unsigned value to configure the AC for no ack policy |
| * This attribute is used to configure the testbed device. |
| * uses the enum qca_wlan_ac_type values |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11, |
| |
| /* 8-bit unsigned value to configure the HE LTF |
| * This attribute is used to configure the testbed device. |
| * Uses the enum qca_wlan_he_ltf_cfg values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12, |
| |
| /* 8-bit unsigned value to configure the tx beamformee. |
| * This attribute is used to configure the testbed device. |
| * 1 - enable, 0 - disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13, |
| |
| /* 8-bit unsigned value to configure the tx beamformee number of |
| * space-time streams. |
| * This attribute is used to configure the testbed device. |
| * The range of the value is 0 to 8 |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14, |
| |
| /* 8-bit unsigned value to configure the MU EDCA params for given AC |
| * This attribute is used to configure the testbed device. |
| * Uses the enum qca_wlan_ac_type values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15, |
| |
| /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC |
| * To configure MU EDCA AIFSN value, MU EDCA access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16, |
| |
| /* 8-bit unsigned value to configure the MU EDCA ECW min value for |
| * given AC. |
| * To configure MU EDCA ECW min value, MU EDCA access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17, |
| |
| /* 8-bit unsigned value to configure the MU EDCA ECW max value for |
| * given AC. |
| * To configure MU EDCA ECW max value, MU EDCA access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18, |
| |
| /* 8-bit unsigned value to configure the MU EDCA timer for given AC |
| * To configure MU EDCA timer value, MU EDCA access category value |
| * is required to process the command. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19, |
| |
| /* 8-bit unsigned value to configure the HE trigger frame MAC padding |
| * duration. |
| * This attribute is used to configure the testbed device. |
| * Uses the enum qca_wlan_he_mac_padding_dur values. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20, |
| |
| /* 8-bit unsigned value to override the MU EDCA params to defaults |
| * regardless of the AP beacon MU EDCA params. If it is enabled use |
| * the default values else use the MU EDCA params from AP beacon. |
| * This attribute is used to configure the testbed device. |
| * 1 - enable override, 0 - disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21, |
| |
| /* 8-bit unsigned value to configure the support for receiving |
| * an MPDU that contains an operating mode control subfield. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22, |
| |
| /* Nested attribute values required to setup the TWT session. |
| * enum qca_wlan_vendor_attr_twt_setup provides the necessary |
| * information to set up the session. It contains broadcast flags, |
| * set_up flags, trigger value, flow type, flow ID, wake interval |
| * exponent, protection, target wake time, wake duration, wake interval |
| * mantissa. These nested attributes are used to setup a host triggered |
| * TWT session. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23, |
| |
| /* This nested attribute is used to terminate the current TWT session. |
| * It does not currently carry any attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24, |
| |
| /* This nested attribute is used to suspend the current TWT session. |
| * It does not currently carry any attributes. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25, |
| |
| /* Nested attribute values to indicate the request for resume. |
| * This attribute is used to resume the TWT session. |
| * enum qca_wlan_vendor_attr_twt_resume provides the necessary |
| * parameters required to resume the TWT session. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26, |
| |
| /* 8-bit unsigned value to set the HE operating mode control |
| * (OM CTRL) Channel Width subfield. |
| * The Channel Width subfield indicates the operating channel width |
| * supported by the STA for both reception and transmission. |
| * Uses the enum qca_wlan_he_om_ctrl_ch_bw values. |
| * This setting is cleared with the |
| * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG |
| * flag attribute to reset defaults. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW = 27, |
| |
| /* 8-bit unsigned value to configure the number of spatial |
| * streams in HE operating mode control field. |
| * This setting is cleared with the |
| * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG |
| * flag attribute to reset defaults. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS = 28, |
| |
| /* Flag attribute to configure the UL MU disable bit in |
| * HE operating mode control field. |
| * This setting is cleared with the |
| * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG |
| * flag attribute to reset defaults. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE = 29, |
| |
| /* Flag attribute to clear the previously set HE operating mode |
| * control field configuration. |
| * This attribute is used to configure the testbed device to reset |
| * defaults to clear any previously set HE operating mode control |
| * field configuration. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG = 30, |
| |
| /* 8-bit unsigned value to configure HE single user PPDU |
| * transmission. By default this setting is disabled and it |
| * is disabled in the reset defaults of the device configuration. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU = 31, |
| |
| /* 8-bit unsigned value to configure action frame transmission |
| * in HE trigger based PPDU transmission. |
| * By default this setting is disabled and it is disabled in |
| * the reset defaults of the device configuration. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU = 32, |
| |
| /* Nested attribute to indicate HE operating mode control field |
| * transmission. It contains operating mode control field Nss, |
| * channel bandwidth, Tx Nsts and UL MU disable attributes. |
| * These nested attributes are used to send HE operating mode control |
| * with configured values. |
| * Uses the enum qca_wlan_vendor_attr_he_omi_tx attributes. |
| * This attribute is used to configure the testbed device. |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX = 33, |
| |
| /* 8-bit unsigned value to configure +HTC_HE support to indicate the |
| * support for the reception of a frame that carries an HE variant |
| * HT Control field. |
| * This attribute is used to configure the testbed device. |
| * 1-enable, 0-disable |
| */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_HTC_HE_SUPP = 34, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX = |
| QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for |
| * TWT (Target Wake Time) setup request. These attributes are sent as part of |
| * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and |
| * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute. |
| * Disable (flag attribute not present) - Individual TWT |
| * Enable (flag attribute present) - Broadcast TWT. |
| * Individual means the session is between the STA and the AP. |
| * This session is established using a separate negotiation between |
| * STA and AP. |
| * Broadcast means the session is across multiple STAs and an AP. The |
| * configuration parameters are announced in Beacon frames by the AP. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8). |
| * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to |
| * specify the TWT request type |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute |
| * Enable (flag attribute present) - TWT with trigger support. |
| * Disable (flag attribute not present) - TWT without trigger support. |
| * Trigger means the AP will send the trigger frame to allow STA to send data. |
| * Without trigger, the STA will wait for the MU EDCA timer before |
| * transmitting the data. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8) |
| * 0 - Announced TWT - In this mode, STA may skip few service periods to |
| * save more power. If STA wants to wake up, it will send a PS-POLL/QoS |
| * NULL frame to AP. |
| * 1 - Unannounced TWT - The STA will wakeup during every SP. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8) |
| * Flow ID is the unique identifier for each TWT session. |
| * Currently this is not required and dialog ID will be set to zero. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8) |
| * This attribute (exp) is used along with the mantissa to derive the |
| * wake interval using the following formula: |
| * pow(2,exp) = wake_intvl_us/wake_intvl_mantis |
| * Wake interval is the interval between 2 successive SP. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute |
| * Enable (flag attribute present) - Protection required. |
| * Disable (flag attribute not present) - Protection not required. |
| * If protection is enabled, then the AP will use protection |
| * mechanism using RTS/CTS to self to reserve the airtime. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32) |
| * This attribute is used as the SP offset which is the offset from |
| * TSF after which the wake happens. The units are in microseconds. If |
| * this attribute is not provided, then the value will be set to zero. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32) |
| * This is the duration of the service period. The units are in TU. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32) |
| * This attribute is used to configure wake interval mantissa. |
| * The units are in TU. |
| */ |
| enum qca_wlan_vendor_attr_twt_setup { |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX = |
| QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_twt_resume: Represents attributes for |
| * TWT (Target Wake Time) resume request. These attributes are sent as part of |
| * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and |
| * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8) |
| * This attribute is used as the SP offset which is the offset from |
| * TSF after which the wake happens. The units are in microseconds. |
| * If this attribute is not provided, then the value will be set to |
| * zero. |
| * |
| * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32) |
| * This attribute represents the next TWT subfield size. |
| */ |
| enum qca_wlan_vendor_attr_twt_resume { |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX = |
| QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_twt_setup_req_type - Required (u8) |
| * Represents the setup type being requested for TWT. |
| * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT |
| * parameters but relying on AP to fill the parameters during the negotiation. |
| * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested |
| * values which the AP may accept or AP may provide alternative parameters |
| * which the STA may accept. |
| * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any |
| * alternate parameters than the requested ones. |
| */ |
| enum qca_wlan_vendor_twt_setup_req_type { |
| QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1, |
| QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2, |
| QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3, |
| }; |
| |
| /** |
| * enum qca_wlan_throughput_level - Current throughput level |
| * |
| * Indicates the current level of throughput calculated by driver. The driver |
| * may choose different thresholds to decide whether the throughput level is |
| * low or medium or high based on variety of parameters like physical link |
| * capacity of current connection, number of pakcets being dispatched per |
| * second etc. The throughput level events might not be consistent with the |
| * actual current throughput value being observed. |
| * |
| * @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput |
| * @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput |
| * @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput |
| */ |
| enum qca_wlan_throughput_level { |
| QCA_WLAN_THROUGHPUT_LEVEL_LOW = 0, |
| QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM = 1, |
| QCA_WLAN_THROUGHPUT_LEVEL_HIGH = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to |
| * report throughput changes from driver to user space. enum values are used |
| * for NL attributes sent with |
| * %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command. |
| */ |
| enum qca_wlan_vendor_attr_throughput_change { |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID = 0, |
| /* |
| * Indicates the direction of throughput in which the change is being |
| * reported. u8 attribute. Value is 0 for TX and 1 for RX. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION = 1, |
| |
| /* |
| * Indicates the newly observed throughput level. |
| * qca_wlan_throughput_level describes the possible range of values. |
| * u8 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL = 2, |
| |
| /* |
| * Indicates the driver's guidance on the new value to be set to |
| * kernel's tcp parameter tcp_limit_output_bytes. u32 attribute. Driver |
| * may optionally include this attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES = 3, |
| |
| /* |
| * Indicates the driver's guidance on the new value to be set to |
| * kernel's tcp parameter tcp_adv_win_scale. s8 attribute. Possible |
| * values are from -31 to 31. Driver may optionally include this |
| * attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE = 4, |
| |
| /* |
| * Indicates the driver's guidance on the new value to be set to |
| * kernel's tcp parameter tcp_delack_seg. u32 attribute. Driver may |
| * optionally include this attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG = 5, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX = |
| QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST - 1, |
| }; |
| |
| /* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute |
| * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. |
| */ |
| enum qca_wlan_nan_ext_subcmd_type { |
| /* Subcmd of type NAN Enable Request */ |
| QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1, |
| /* Subcmd of type NAN Disable Request */ |
| QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2, |
| }; |
| |
| /** |
| * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. |
| */ |
| enum qca_wlan_vendor_attr_nan_params { |
| QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0, |
| /* Carries NAN command for firmware component. Every vendor command |
| * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a |
| * payload containing the NAN command. NLA_BINARY attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1, |
| /* Indicates the type of NAN command sent with |
| * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type |
| * describes the possible range of values. This attribute is mandatory |
| * if the command being issued is either |
| * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or |
| * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2, |
| /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz |
| * band. This attribute is mandatory when command type is |
| * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3, |
| /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz |
| * band. This attribute is optional and should be included when command |
| * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery |
| * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute. |
| */ |
| QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4, |
| |
| /* keep last */ |
| QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST, |
| QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX = |
| QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1 |
| }; |
| #endif |