/*
 * Copyright (c) 2012-2019 The Linux Foundation. All rights reserved.
 *
 * Permission to use, copy, modify, and/or distribute this software for
 * any purpose with or without fee is hereby granted, provided that the
 * above copyright notice and this permission notice appear in all
 * copies.
 *
 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
 * WARRANTIES WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED
 * WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE
 * AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL
 * DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
 * PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
 * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR
 * PERFORMANCE OF THIS SOFTWARE.
 */

/**
 * DOC: This file contains centralized definitions of converged configuration.
 */

#ifndef __HDD_CONFIG_H
#define __HDD_CONFIG_H

#if defined(CONFIG_HL_SUPPORT)
#include "wlan_tgt_def_config_hl.h"
#else
#include "wlan_tgt_def_config.h"
#endif

#define CFG_QDF_TRACE_ENABLE_DEFAULT (0xffff)
#include <wlan_action_oui_public_struct.h>

/**
 * enum hdd_wext_control - knob for wireless extensions
 * @hdd_wext_disabled - interface is completely disabled. An access
 *      control error log will be generated for each attempted use.
 * @hdd_wext_deprecated - interface is available but should not be
 *      used. An access control warning log will be generated for each
 *      use.
 * @hdd_wext_enabled - interface is available without restriction. No
 *      access control logs will be generated.
 *
 * enum hdd_wext_control is used to enable coarse grained control on
 * wireless extensions ioctls. This control is used by configuration
 * item private_wext_control.
 *
 */
enum hdd_wext_control {
	hdd_wext_disabled = 0,
	hdd_wext_deprecated = 1,
	hdd_wext_enabled = 2,
};

/*
 * <ini>
 * private_wext_control - Private wireless extensions control
 * @Min: 0
 * @Max: 2
 * @Default: 1
 *
 * Values are per enum hdd_wext_control.
 * This ini is used to control access to private wireless extensions
 * ioctls SIOCIWFIRSTPRIV (0x8BE0) thru SIOCIWLASTPRIV (0x8BFF). The
 * functionality provided by some of these ioctls has been superceeded
 * by cfg80211 (either standard commands or vendor commands), but many
 * of the private ioctls do not have a cfg80211-based equivalent, so
 * by default support for these ioctls is deprecated.
 *
 * Related: None
 *
 * Supported Feature: All
 *
 * Usage: Internal/External
 *
 * </ini>
 */
#define CFG_PRIVATE_WEXT_CONTROL CFG_INI_UINT( \
			"private_wext_control", \
			hdd_wext_disabled, \
			hdd_wext_enabled, \
			hdd_wext_deprecated, \
			CFG_VALUE_OR_DEFAULT, \
			"Private WEXT Control")

enum hdd_dot11_mode {
	eHDD_DOT11_MODE_AUTO = 0,       /* covers all things we support */
	eHDD_DOT11_MODE_abg,    /* 11a/b/g only, no HT, no proprietary */
	eHDD_DOT11_MODE_11b,
	eHDD_DOT11_MODE_11g,
	eHDD_DOT11_MODE_11n,
	eHDD_DOT11_MODE_11g_ONLY,
	eHDD_DOT11_MODE_11n_ONLY,
	eHDD_DOT11_MODE_11b_ONLY,
	eHDD_DOT11_MODE_11ac_ONLY,
	eHDD_DOT11_MODE_11ac,
	eHDD_DOT11_MODE_11a,
	eHDD_DOT11_MODE_11ax_ONLY,
	eHDD_DOT11_MODE_11ax,
};

/*
 * <ini>
 * gDot11Mode - Phymode of vdev
 * @Min: 0 (auto)
 * @Max: 12 (11ax)
 * @Default: 12 (11ax)
 *
 * This ini is used to set Phy Mode (auto, b, g, n, etc/) Valid values are
 * 0-12, with 0 = Auto, 12 = 11ax.
 *
 * Related: None.
 *
 * Supported Feature: SAP
 *
 * Usage: Internal/External
 *
 * </ini>
 */
 #define CFG_HDD_DOT11_MODE CFG_INI_UINT( \
			"gDot11Mode", \
			eHDD_DOT11_MODE_AUTO, \
			eHDD_DOT11_MODE_11ax, \
			eHDD_DOT11_MODE_11ax, \
			CFG_VALUE_OR_DEFAULT, \
			"dot11 mode")

/*
 * <ini>
 * gInterfaceChangeWait - Interface change wait
 * @Min: 0,
 * @Max: 500000
 * @Default: 10000
 *
 * Timer waiting for interface up from the upper layer. If
 * this timer expires all the cds modules shall be closed.
 * Time Units: ms
 *
 * Value 0 can be used to disable idle module stop.
 *
 * Related: None
 *
 * Supported Feature: All
 *
 * </ini>
 */
#define CFG_INTERFACE_CHANGE_WAIT CFG_INI_UINT( \
			"gInterfaceChangeWait", \
			0, \
			500000, \
			10000, \
			CFG_VALUE_OR_DEFAULT, \
			"Interface change wait")

#ifdef QCA_WIFI_NAPIER_EMULATION
#define CFG_TIMER_MULTIPLIER_DEFAULT	100
#else
#define CFG_TIMER_MULTIPLIER_DEFAULT	1
#endif

/*
 * <ini>
 * gTimerMultiplier - Scale QDF timers by this value
 * @Min: 1
 * @Max: 0xFFFFFFFF
 * @Default: 1 (100 for emulation)
 *
 * To assist in debugging emulation setups, scale QDF timers by this factor.
 *
 * @E.g.
 *	# QDF timers expire in real time
 *	gTimerMultiplier=1
 *	# QDF timers expire after 100 times real time
 *	gTimerMultiplier=100
 *
 * Related: None
 *
 * Usage: Internal
 *
 * </ini>
 */
#define CFG_TIMER_MULTIPLIER CFG_INI_UINT( \
			"gTimerMultiplier", \
			1, \
			0xFFFFFFFF, \
			CFG_TIMER_MULTIPLIER_DEFAULT, \
			CFG_VALUE_OR_DEFAULT, \
			"Timer Multiplier")

#define CFG_BUG_ON_REINIT_FAILURE_DEFAULT 1
/*
 * <ini>
 * g_bug_on_reinit_failure  - Enable/Disable bug on reinit
 * @Min: 0
 * @Max: 1
 * @Default: 1
 *
 * This ini is used to debug ssr reinit failure issues by raising vos bug so
 * dumps can be collected.
 * g_bug_on_reinit_failure = 0 wlan driver will only recover after driver
 * unload and load
 * g_bug_on_reinit_failure = 1 raise vos bug to collect dumps
 *
 * Related: gEnableSSR
 *
 * Supported Feature: SSR
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_BUG_ON_REINIT_FAILURE CFG_INI_BOOL( \
		"g_bug_on_reinit_failure", \
		CFG_BUG_ON_REINIT_FAILURE_DEFAULT, \
		"BUG on reinit failure")

/*
 * <ini>
 * gEnableDumpCollect - It will use for collect the dumps
 * @Min: 0
 * @Max: 1
 * @Default: 1
 *
 * This ini is used to set collect default dump
 *
 * Related: None
 *
 * Supported Feature: STA
 *
 * Usage: Internal/External
 *
 * </ini>
 */
#define CFG_ENABLE_RAMDUMP_COLLECTION CFG_INI_BOOL( \
			"gEnableDumpCollect", \
			1, \
			"Enable dump collect")

#if defined(MDM_PLATFORM) && !defined(FEATURE_MULTICAST_HOST_FW_MSGS)
#define CFG_MULTICAST_HOST_FW_MSGS_DEFAULT	0
#else
#define CFG_MULTICAST_HOST_FW_MSGS_DEFAULT	1
#endif

/*
 * <ini>
 * gMulticastHostFwMsgs - Multicast host FW messages
 * @Min: 0
 * @Max: 1
 * @Default: 0 for MDM platform and 1 for other
 *
 * </ini>
 */
#define CFG_MULTICAST_HOST_FW_MSGS CFG_INI_UINT( \
			"gMulticastHostFwMsgs", \
			0, \
			1, \
			CFG_MULTICAST_HOST_FW_MSGS_DEFAULT, \
			CFG_VALUE_OR_DEFAULT, \
			"Multicast host FW msgs")

#ifdef WLAN_LOGGING_SOCK_SVC_ENABLE
/*
 * <ini>
 * wlanLoggingEnable - Wlan logging enable
 * @Min: 0
 * @Max: 1
 * @Default: 1
 *
 * </ini>
 */
#define CFG_WLAN_LOGGING_SUPPORT CFG_INI_BOOL( \
				"wlanLoggingEnable", \
				1, \
				"Wlan logging enable")

/*
 * <ini>
 * host_log_custom_nl_proto - Host log netlink protocol
 * @Min: 0
 * @Max: 32
 * @Default: 2
 *
 * This ini is used to set host log netlink protocol. The default
 * value is 2 (NETLINK_USERSOCK), customer should avoid selecting the
 * netlink protocol that already used on their platform by other
 * applications or services. By choosing the non-default value(2),
 * Customer need to change the netlink protocol of application receive
 * tool(cnss_diag) accordingly. Available values could be:
 *
 * host_log_custom_nl_proto = 0 -	NETLINK_ROUTE, Routing/device hook
 * host_log_custom_nl_proto = 1 -	NETLINK_UNUSED, Unused number
 * host_log_custom_nl_proto = 2 -	NETLINK_USERSOCK, Reserved for user
 *					mode socket protocols
 * host_log_custom_nl_proto = 3 -	NETLINK_FIREWALL, Unused number,
 *					formerly ip_queue
 * host_log_custom_nl_proto = 4 -	NETLINK_SOCK_DIAG, socket monitoring
 * host_log_custom_nl_proto = 5 -	NETLINK_NFLOG, netfilter/iptables ULOG
 * host_log_custom_nl_proto = 6 -	NETLINK_XFRM, ipsec
 * host_log_custom_nl_proto = 7 -	NETLINK_SELINUX, SELinux event
 *					notifications
 * host_log_custom_nl_proto = 8 -	NETLINK_ISCSI, Open-iSCSI
 * host_log_custom_nl_proto = 9 -	NETLINK_AUDIT, auditing
 * host_log_custom_nl_proto = 10 -	NETLINK_FIB_LOOKUP
 * host_log_custom_nl_proto = 11 -	NETLINK_CONNECTOR
 * host_log_custom_nl_proto = 12 -	NETLINK_NETFILTER, netfilter subsystem
 * host_log_custom_nl_proto = 13 -	NETLINK_IP6_FW
 * host_log_custom_nl_proto = 14 -	NETLINK_DNRTMSG, DECnet routing messages
 * host_log_custom_nl_proto = 15 -	NETLINK_KOBJECT_UEVENT, Kernel
 *					messages to userspace
 * host_log_custom_nl_proto = 16 -	NETLINK_GENERIC, leave room for
 *					NETLINK_DM (DM Events)
 * host_log_custom_nl_proto = 18 -	NETLINK_SCSITRANSPORT, SCSI Transports
 * host_log_custom_nl_proto = 19 -	NETLINK_ECRYPTFS
 * host_log_custom_nl_proto = 20 -	NETLINK_RDMA
 * host_log_custom_nl_proto = 21 -	NETLINK_CRYPTO, Crypto layer
 * host_log_custom_nl_proto = 22 -	NETLINK_SMC, SMC monitoring
 *
 * The max value is: MAX_LINKS which is 32
 *
 * Related: None
 *
 * Supported Feature: STA
 *
 * Usage: Internal/External
 *
 * </ini>
 */
#define CFG_HOST_LOG_CUSTOM_NETLINK_PROTO CFG_INI_UINT( \
	"host_log_custom_nl_proto", \
	0, \
	32, \
	2, \
	CFG_VALUE_OR_DEFAULT, \
	"host log custom netlink protocol")

/*
 * <ini>
 * wlanLoggingToConsole - Wlan logging to console
 * @Min: 0
 * @Max: 1
 * @Default: 1
 *
 * </ini>
 */
#define CFG_WLAN_LOGGING_CONSOLE_SUPPORT CFG_INI_BOOL( \
				"wlanLoggingToConsole", \
				1, \
				"Wlan logging to console")

#define CFG_WLAN_LOGGING_SUPPORT_ALL \
	CFG(CFG_WLAN_LOGGING_SUPPORT) \
	CFG(CFG_WLAN_LOGGING_CONSOLE_SUPPORT) \
	CFG(CFG_HOST_LOG_CUSTOM_NETLINK_PROTO)
#else
#define CFG_WLAN_LOGGING_SUPPORT_ALL
#endif

#ifdef FEATURE_WLAN_AUTO_SHUTDOWN
/*
 * <ini>
 * gWlanAutoShutdown - Wlan auto shutdown timer value
 * @Min: 0
 * @Max: 86400
 * @Default: 0
 *
 * This ini specifies the seconds of WLAN inactivity firmware has to wait
 * before indicating WLAN idle event to driver. Upon receiving firmware's
 * WLAN idle indication, driver may indicate similar event to upper layer
 * daemons(SCM, or any other components working to achieve the same purpose),
 * who may choose what to do next, e.g. whether to unload driver module or not.
 * 0 indicates no auto shutdown will take place.
 *
 * </ini>
 */
#define CFG_WLAN_AUTO_SHUTDOWN CFG_INI_UINT( \
			"gWlanAutoShutdown", \
			0, \
			86400, \
			0, \
			CFG_VALUE_OR_DEFAULT, \
			"Wlan auto shutdown")
#define CFG_WLAN_AUTO_SHUTDOWN_ALL \
	CFG(CFG_WLAN_AUTO_SHUTDOWN)
#else
#define CFG_WLAN_AUTO_SHUTDOWN_ALL
#endif

/*
 * <ini>
 * gEnablefwprint - Enable FW uart print
 * @Min: 0
 * @Max: 1
 * @Default: 0
 *
 * </ini>
 */
#define CFG_ENABLE_FW_UART_PRINT CFG_INI_BOOL( \
			"gEnablefwprint", \
			0, \
			"Enable FW uart print")

/*
 * <ini>
 * gEnablefwlog - Enable FW log
 * @Min: 0
 * @Max: 2
 * @Default: 1
 *
 * </ini>
 */
#define CFG_ENABLE_FW_LOG CFG_INI_UINT( \
			"gEnablefwlog", \
			0, \
			2, \
			1, \
			CFG_VALUE_OR_DEFAULT, \
			"Enable FW log")

#ifndef REMOVE_PKT_LOG

#ifdef FEATURE_PKTLOG
#define CFG_ENABLE_PACKET_LOG_DEFAULT	1
#else
#define CFG_ENABLE_PACKET_LOG_DEFAULT	0
#endif

/*
 * <ini>
 * gEnablePacketLog - Enale packet log
 * @Min: 0
 * @Max: 1
 * @Default: 1 if packet log code is enabled, 0 otherwise
 *
 * This option enables/disables packet log collecting.
 *
 * </ini>
 */
#define CFG_ENABLE_PACKET_LOG CFG_INI_BOOL( \
			"gEnablePacketLog", \
			CFG_ENABLE_PACKET_LOG_DEFAULT, \
			"Enable packet log")

#define CFG_ENABLE_PACKET_LOG_ALL \
	CFG(CFG_ENABLE_PACKET_LOG)
#else
#define CFG_ENABLE_PACKET_LOG_ALL
#endif

#ifdef FEATURE_RUNTIME_PM
/*
 * <ini>
 * gRuntimePM - enable runtime suspend
 * @Min: 0
 * @Max: 1
 * @Default: 0
 *
 * This ini is used to enable runtime_suspend
 *
 * Related: None
 *
 * Supported Feature: Power Save
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ENABLE_RUNTIME_PM CFG_INI_BOOL( \
		"gRuntimePM", \
		0, \
		"This ini is used to enable runtime_suspend")
#define CFG_ENABLE_RUNTIME_PM_ALL \
	CFG(CFG_ENABLE_RUNTIME_PM)
#else
#define CFG_ENABLE_RUNTIME_PM_ALL
#endif

/*
 * <ini>
 * gInformBssRssiRaw - Report rssi in cfg80211_inform_bss_frame
 * @Min: 0
 * @Max: 1
 * @Default: 1
 *
 * Option to report rssi in cfg80211_inform_bss_frame()
 *
 * Related: None
 *
 * Supported Feature: N/A
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_INFORM_BSS_RSSI_RAW CFG_INI_BOOL( \
		"gInformBssRssiRaw", \
		1, \
		"Option to report rssi in cfg80211_inform_bss_frame")

#ifdef FEATURE_WLAN_DYNAMIC_CVM
/*
 * <ini>
 * gConfigVCmodeBitmap - Bitmap for operating voltage corner mode
 * @Min: 0x00000000
 * @Max: 0x0fffffff
 * @Default: 0x0000000a
 * This ini is used to set operating voltage corner mode for differenet
 * phymode and bw configurations. Every 2 bits till BIT27 are dedicated
 * for a specific configuration. Bit values decide the type of voltage
 * corner mode. All the details below -
 *
 * Configure operating voltage corner mode based on phymode and bw.
 * bit 0-1 -   operating voltage corner mode for 11a/b.
 * bit 2-3 -   operating voltage corner mode for 11g.
 * bit 4-5 -   operating voltage corner mode for 11n, 20MHz, 1x1.
 * bit 6-7 -   operating voltage corner mode for 11n, 20MHz, 2x2.
 * bit 8-9 -   operating voltage corner mode for 11n, 40MHz, 1x1.
 * bit 10-11 - operating voltage corner mode for 11n, 40MHz, 2x2.
 * bit 12-13 - operating voltage corner mode for 11ac, 20MHz, 1x1.
 * bit 14-15 - operating voltage corner mode for 11ac, 20MHz, 2x2.
 * bit 16-17 - operating voltage corner mode for 11ac, 40MHz, 1x1.
 * bit 18-19 - operating voltage corner mode for 11ac, 40MHz, 2x2.
 * bit 20-21 - operating voltage corner mode for 11ac, 80MHz, 1x1.
 * bit 22-23 - operating voltage corner mode for 11ac, 80MHz, 2x2.
 * bit 24-25 - operating voltage corner mode for 11ac, 160MHz, 1x1.
 * bit 26-27 - operating voltage corner mode for 11ac, 160MHz, 2x2.
 * ---------------------------------------------
 * 00 - Static voltage corner SVS
 * 01 - static voltage corner LOW SVS
 * 10 - Dynamic voltage corner selection based on TPUT
 * 11 - Dynamic voltage corner selection based on TPUT and Tx Flush counters

 * Related: None
 *
 * Supported Feature: None
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_VC_MODE_BITMAP CFG_INI_INT( \
	"gConfigVCmode", \
	0x00000000, \
	0x0fffffff, \
	0x00000005, \
	CFG_VALUE_OR_DEFAULT, \
	"Bitmap for operating voltage corner mode")

#define CFG_VC_MODE_BITMAP_ALL CFG(CFG_VC_MODE_BITMAP)
#else
#define CFG_VC_MODE_BITMAP_ALL
#endif

/*
 * <ini>
 * gOperatingChannel- Default STA operating channel
 * @Min: 0
 * @Max: 14
 * @Default: 1
 *
 * This ini is used to specify the default operating channel of a STA during
 * initialization.
 *
 * Related: None
 *
 * Supported Feature: STA
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_OPERATING_CHANNEL CFG_INI_UINT( \
			"gOperatingChannel", \
			0, \
			14, \
			1, \
			CFG_VALUE_OR_DEFAULT, \
			"Default Operating Channel")

#ifdef DHCP_SERVER_OFFLOAD
#define IPADDR_NUM_ENTRIES     (4)
#define IPADDR_STRING_LENGTH   (16)
#define CFG_DHCP_SERVER_IP_DEFAULT  ""

/*
 * struct wlan_mlme_chainmask - All chainmask related cfg items
 * @dhcpServerIP:     Dhcp server IP address
 * @is_dhcp_server_ip_valid:     is dhcp server valid
 */
struct dhcp_server {
	uint8_t dhcp_server_ip[IPADDR_NUM_ENTRIES];
	bool is_dhcp_server_ip_valid;
}

/*
 * <ini>
 * gDHCPServerIP - Dhcp server Ip name
 * @Default:
 *
 * This ini is used to give the DHCP IP server name
 */
#define CFG_DHCP_SERVER_IP_NAME \
	CFG_INI_STRING("gDHCPServerIP", \
	0, IPADDR_STRING_LENGTH, CFG_DHCP_SERVER_IP_DEFAULT, "DHCP Server IP")
#endif /* DHCP_SERVER_OFFLOAD */

/*
 * <ini>
 * gNumVdevs - max number of VDEVs supported
 *
 * @Min: 0x1
 * @Max: 0x4
 * @Default: CFG_TGT_NUM_VDEV
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_NUM_VDEV_ENABLE CFG_INI_UINT( \
		"gNumVdevs", \
		1, \
		4, \
		CFG_TGT_NUM_VDEV, \
		CFG_VALUE_OR_DEFAULT, \
		"Number of VDEVs")

#define CFG_CONCURRENT_IFACE_MAX_LEN 16
/*
 * <ini>
 * gEnableConcurrentSTA - This will control the creation of concurrent STA
 * interface
 * @Default: NULL
 *
 * This ini is used for providing control to create a concurrent STA session
 * along with the creation of wlan0 and p2p0. The name of the interface is
 * specified as the parameter
 *
 * Usage: Internal
 *
 * </ini>
 */

#define CFG_ENABLE_CONCURRENT_STA CFG_INI_STRING( \
		"gEnableConcurrentSTA", \
		0, \
		CFG_CONCURRENT_IFACE_MAX_LEN, \
		"", \
		"Enable Concurrent STA")

#define CFG_DBS_SCAN_PARAM_LENGTH 42
/*
 * <ini>
 * gdbs_scan_selection - DBS Scan Selection.
 * @Default: ""
 *
 * This ini is used to enable DBS scan selection.
 * Example
 * @Value: "5,2,2,16,2,2"
 * 1st argument is module_id, 2nd argument is number of DBS scan,
 * 3rd argument is number of non-DBS scan,
 * and other arguments follows.
 * 5,2,2,16,2,2 means:
 * 5 is module id, 2 is num of DBS scan, 2 is num of non-DBS scan.
 * 16 is module id, 2 is num of DBS scan, 2 is num of non-DBS scan.
 *
 * Related: None.
 *
 * Supported Feature: DBS Scan
 *
 * Usage: Internal/External
 *
 * </ini>
 */
#define CFG_DBS_SCAN_SELECTION CFG_INI_STRING( \
			"gdbs_scan_selection", \
			0, \
			CFG_DBS_SCAN_PARAM_LENGTH, \
			"", \
			"DBS Scan Selection")

/*
 * </ini>
 * enable_mac_provision - Enable/disable MAC address provisioning feature
 * @Min: 0
 * @Max: 1
 * @Default: 0
 *
 * This ini is used to enable/disable MAC address provisioning feature
 *
 * Supported Feature: STA/SAP/P2P
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ENABLE_MAC_PROVISION CFG_INI_BOOL( \
	"enable_mac_provision", \
	0, \
	"enable/disable MAC address provisioning feature")

/*
 * <ini>
 * provisioned_intf_pool - It is bit mask value of Interfaces
 * @Min: 0
 * @Max: 0xffffffff
 * @Default: 0xffffffff
 *
 * This ini will contain the bitmask of all the interfaces
 * which can use addresses from provisioned list. Using enum QDF_OPMODE
 * for deciding the bit positions corresponding to each interface.
 * Bit 0 : QDF_STA_MODE
 * Bit 1 : QDF_SAP_MODE
 * Bit 2 : QDF_P2P_CLIENT_MODE
 * Bit 3 : QDF_P2P_GO_MODE
 * Bit 4 : QDF_FTM_MODE
 * Bit 5 : QDF_IBSS_MODE
 * Bit 6 : QDF_MONITOR_MODE
 * Bit 7 : QDF_P2P_DEVICE_MODE
 * Bit 8 : QDF_OCB_MODE
 * Bit 9 : QDF_EPPING_MODE
 * Bit 10 : QDF_QVIT_MODE
 * Bit 11 : QDF_NDI_MODE
 * Bit 12 : QDF_MAX_NO_OF_MODE
 * For example :
 * If Bit 0 represents STA
 * Bit 1 represents SAP
 * Bit 2 represents P2PGO
 * If only STA and SAP can use addresses from provisioned list then the value
 * of ini should be 3 (00000011) as first and second bit should be set.
 * If only STA and P2PGO can use addresses from provisioned list then the value
 * of ini should be 5 (00000101) as first and third bit should be set.
 * Similarly, for only SAP and P2PGO ini should be 6 (00000110)
 *
 * Supported Feature: STA/SAP/P2P
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_PROVISION_INTERFACE_POOL CFG_INI_UINT( \
			"provisioned_intf_pool", \
			0, \
			0xffffffff, \
			0xffffffff, \
			CFG_VALUE_OR_DEFAULT, \
			"It is bit mask value of Interfaces")

/*
 * <ini>
 * deriveded_intf_pool - It is bit mask value of Interfaces
 * @Min: 0
 * @Max: 0xffffffff
 * @Default: 0xffffffff
 *
 * This ini will contain the bitmask of all the interfaces
 * which can use addresses from derived list
 *
 *
 * Supported Feature: STA/SAP/P2P
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_DERIVED_INTERFACE_POOL CFG_INI_UINT( \
				"derived_intf_pool", \
				0, \
				0xffffffff, \
				0xffffffff, \
				CFG_VALUE_OR_DEFAULT, \
				"It is bit mask value of Interfaces")

/*
 * Start of action oui inis
 *
 * To enable action oui feature, set gEnableActionOUI
 *
 * Each action oui is expected in the following format:
 * <Extension 1> <Extension 2> ..... <Extension 10> (maximum 10)
 *
 * whereas, each Extension is separated by space and have the following format:
 * <Token1> <Token2> <Token3> <Token4> <Token5> <Token6> <Token7> <Token8>
 * where each Token is a string of hexa-decimal digits and
 * following are the details about each token
 *
 * Token1 = OUI
 * Token2 = Data_Length
 * Token3 = Data
 * Token4 = Data_Mask
 * Token5 = Info_Presence_Bit
 * Token6 = MAC_Address
 * Token7 = Mac_Address Mask
 * Token8 = Capability
 *
 * <OUI> is mandatory and it can be either 3 or 5 bytes means 6 or 10
 * hexa-decimal characters
 * If the OUI and Data checks needs to be ignored, the oui FFFFFF
 * needs to be provided as OUI and bit 0 of Info_Presence_Bit should
 * be set to 0.
 *
 * <Data_Length> is mandatory field and should give length of
 * the <Data> if present else zero
 *
 * Presence of <Data> is controlled by <Data_Length>, if <Data_Length> is 0,
 * then <Data> is not expected else Data of the size Data Length bytes are
 * expected which means the length of Data string is 2 * Data Length,
 * since every byte constitutes two hexa-decimal characters.
 *
 * <Data_Mask> is mandatory if <Data> is present and length of the
 * Data mask string depends on the <Data Length>
 * If <Data Length> is 06, then length of Data Mask string is
 * 2 characters (represents 1 byte)
 * data_mask_length = ((Data_Length - (Data_Length % 8)) / 8) +
 *		      ((Data_Length % 8) ? 1 : 0)
 * and <Data_Mask> has to be constructed from left to right.
 *
 * Presence of <Mac_Address> and <Capability> is
 * controlled by <Info_Presence_Bit> which is mandatory
 * <Info_Presence_Bit> will give the information for
 *   OUI – bit 0 Should be set to 1
 *		 Setting to 0 will ignore OUI and data check
 *   Mac Address present – bit 1
 *   NSS – bit 2
 *   HT check – bit 3
 *   VHT check – bit 4
 *   Band info – bit 5
 *   reserved – bit 6 (should always be zero)
 *   reserved – bit 7 (should always be zero)
 * and should be constructed from right to left (b7b6b5b4b3b2b1b0)
 *
 * <Mac_Address_Mask> for <Mac_Address> should be constructed from left to right
 *
 * <Capability> is 1 byte long and it contains the below info
 *   NSS – 4 bits starting from LSB (b0 – b3)
 *   HT enabled – bit 4
 *   VHT enabled – bit 5
 *   2G band – bit 6
 *   5G band – bit 7
 * and should be constructed from right to left (b7b6b5b4b3b2b1b0)
 * <Capability> is present if atleast one of the bit is set
 * from b2 - b6 in <Info_Presence_Bit>
 *
 * Example 1:
 *
 * OUI is 00-10-18, data length is 05 (hex form), data is 02-11-04-5C-DE and
 * need to consider first 3 bytes and last byte of data for comparision
 * mac-addr EE-1A-59-FE-FD-AF is present and first 3 bytes and last byte of
 * mac address should be considered for comparision
 * capability is not present
 * then action OUI for gActionOUIITOExtension is as follows:
 *
 * gActionOUIITOExtension=001018 05 0211045CDE E8 03 EE1A59FEFDAF E4
 *
 * data mask calculation in above example:
 * Data[0] = 02 ---- d0 = 1
 * Data[1] = 11 ---- d1 = 1
 * Data[2] = 04 ---- d2 = 1
 * Data[3] = 5C ---- d3 = 0
 * Data[4] = DE ---- d4 = 1
 * data_mask = d0d1d2d3d4 + append with zeros to complete 8-bit = 11101000 = E8
 *
 * mac mask calculation in above example:
 * mac_addr[0] = EE ---- m0 = 1
 * mac_addr[1] = 1A ---- m1 = 1
 * mac_addr[2] = 59 ---- m2 = 1
 * mac_addr[3] = FE ---- m3 = 0
 * mac_addr[4] = FD ---- m4 = 0
 * mac_addr[5] = AF ---- m5 = 1
 * mac_mask = m0m1m2m3m4m5 + append with zeros to complete 8-bit = 11100100 = E4
 *
 * Example 2:
 *
 * OUI is 00-10-18, data length is 00 and no Mac Address and capability
 *
 * gActionOUIITOExtension=001018 00 01
 *
 */

/*
 * <ini>
 * gEnableActionOUI - Enable/Disable action oui feature
 * @Min: 0 (disable)
 * @Max: 1 (enable)
 * @Default: 1 (enable)
 *
 * This ini is used to enable the action oui feature to control
 * mode of connection, connected AP's in-activity time, Tx rate etc.,
 *
 * Related: If gEnableActionOUI is set, then at least one of the following inis
 * must be set with the proper action oui extensions:
 * gActionOUIConnect1x1, gActionOUIITOExtension, gActionOUICCKM1X1
 *
 * Supported Feature: action ouis
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ENABLE_ACTION_OUI CFG_INI_BOOL( \
	"gEnableActionOUI", \
	1, \
	"Enable/Disable action oui feature")

/*
 * <ini>
 * gActionOUIConnect1x1 - Used to specify action OUIs for 1x1 connection
 * @Default: 000C43 00 25 42 001018 06 02FFF02C0000 BC 25 42 001018 06 02FF040C0000 BC 25 42 00037F 00 35 6C
 * Note: User should strictly add new action OUIs at the end of this
 * default value.
 *
 * Default OUIs: (All values in Hex)
 * OUI 1 : 000C43
 *   OUI data Len : 00
 *   Info Mask : 25 - Check for NSS and Band
 *   Capabilities: 42 - NSS == 2 && Band == 2G
 * OUI 2 : 001018
 *   OUI data Len : 06
 *   OUI Data : 02FFF02C0000
 *   OUI data Mask: BC - 10111100
 *   Info Mask : 25 - Check for NSS and Band
 *   Capabilities: 42 - NSS == 2 && Band == 2G
 * OUI 3 : 001018
 *   OUI data Len : 06
 *   OUI Data : 02FF040C0000
 *   OUI data Mask: BC - 10111100
 *   Info Mask : 25 - Check for NSS and Band
 *   Capabilities: 42 - NSS == 2 && Band == 2G
 * OUI 4 : 00037F
 *   OUI data Len : 00
 *   Info Mask : 35 - Check for NSS, VHT Caps and Band
 *   Capabilities: 6C - (NSS == 3 or 4) && VHT Caps Preset && Band == 2G
 * OUI 5 : 001018
 *   OUI data Len : 06
 *   OUI Data : 02FF009C0000
 *   OUI data Mask: BC - 10111100
 *   Info Mask : 25 - Check for NSS and Band
 *   Capabilities: 48 - NSS == 4 && Band == 2G
 *
 * This ini is used to specify the AP OUIs with which only 1x1 connection
 * is allowed.
 *
 * Related: None
 *
 * Supported Feature: Action OUIs
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ACTION_OUI_CONNECT_1X1 CFG_INI_STRING( \
	"gActionOUIConnect1x1", \
	0, \
	ACTION_OUI_MAX_STR_LEN, \
	"000C43 00 25 42 001018 06 02FFF02C0000 BC 25 42 001018 06 02FF040C0000 BC 25 42 00037F 00 35 6C 001018 06 02FF009C0000 BC 25 48", \
	"Used to specify action OUIs for 1x1 connection")

/*
 * <ini>
 * gActionOUIITOExtension - Used to extend in-activity time for specified APs
 * @Default: 00037F 06 01010000FF7F FC 01 000AEB 02 0100 C0 01 000B86 03 010408 E0 01
 * Note: User should strictly add new action OUIs at the end of this
 * default value.
 *
 * Default OUIs: (All values in Hex)
 * OUI 1: 00037F
 *   OUI data Len: 06
 *   OUI Data: 01010000FF7F
 *   OUI data Mask: FC - 11111100
 *   Info Mask : 01 - only OUI present in Info mask
 *
 * OUI 2: 000AEB
 *   OUI data Len: 02
 *   OUI Data: 0100
 *   OUI data Mask: C0 - 11000000
 *   Info Mask : 01 - only OUI present in Info mask
 *
 * OUI 3: 000B86
 *   OUI data Len: 03
 *   OUI Data: 010408
 *   OUI data Mask: E0 - 11100000
 *   Info Mask : 01 - only OUI present in Info mask
 *
 * This ini is used to specify AP OUIs using which station's in-activity time
 * can be extended with the respective APs
 *
 * Related: None
 *
 * Supported Feature: Action OUIs
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ACTION_OUI_ITO_EXTENSION CFG_INI_STRING( \
	"gActionOUIITOExtension", \
	0, \
	ACTION_OUI_MAX_STR_LEN, \
	"00037F 06 01010000FF7F FC 01 000AEB 02 0100 C0 01 000B86 03 010408 E0 01", \
	"Used to extend in-activity time for specified APs")

/*
 * <ini>
 * gActionOUICCKM1X1 - Used to specify action OUIs to control station's TX rates
 *
 * This ini is used to specify AP OUIs for which station's CCKM TX rates
 * should be 1x1 only.
 *
 * Related: None
 *
 * Supported Feature: Action OUIs
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ACTION_OUI_CCKM_1X1 CFG_INI_STRING( \
	"gActionOUICCKM1X1", \
	0, \
	ACTION_OUI_MAX_STR_LEN, \
	"", \
	"Used to specify action OUIs to control station's TX rates")

/*
 * <ini>
 * gActionOUIITOAlternate - Used to specify action OUIs to have alternate ITO in
 * weak RSSI state
 *
 * This ini is used to specify AP OUIs for which the stations will have
 * alternate ITOs for the case when the RSSI is weak.
 *
 * Related: None
 *
 * Supported Feature: Action OUIs
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ACTION_OUI_ITO_ALTERNATE CFG_INI_STRING( \
	"gActionOUIITOAlternate", \
	0, \
	ACTION_OUI_MAX_STR_LEN, \
	"001018 06 0202001c0000 FC 01", \
	"Used to specify action OUIs to have alternate ITO")

/*
 * <ini>
 * gActionOUISwitchTo11nMode - Used to specify action OUIs for switching to 11n
 *
 * This ini is used to specify which AP for which the connection has to be
 * made in 2x2 mode with HT capabilities only and not VHT.
 *
 * Default OUIs: (All values in Hex)
 * OUI 1 : 00904C
 *   OUI data Len : 03
 *   OUI Data : 0418BF
 *   OUI data Mask: E0 - 11100000
 *   Info Mask : 21 - Check for Band
 *   Capabilities: 40 - Band == 2G
 *
 * Related: None
 *
 * Supported Feature: Action OUIs
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ACTION_OUI_SWITCH_TO_11N_MODE CFG_INI_STRING( \
	"gActionOUISwitchTo11nMode", \
	0, \
	ACTION_OUI_MAX_STR_LEN, \
	"00904C 05 0418BF0CB2 F8 21 40", \
	"Used to specify action OUIs for switching to 11n")

/*
 * <ini>
 * gActionOUIConnect1x1with1TxRxChain - Used to specify action OUIs for
 *					 1x1 connection with one Tx/Rx Chain
 * @Default:
 * Note: User should strictly add new action OUIs at the end of this
 * default value.
 *
 * Default OUIs: (All values in Hex)
 * OUI 1 : 001018
 *   OUI data Len : 06
 *   OUI Data : 02FFF0040000
 *   OUI data Mask: BC - 10111100
 *   Info Mask : 21 - Check for Band
 *   Capabilities: 40 - Band == 2G
 *
 * OUI 2 : 001018
 *   OUI data Len : 06
 *   OUI Data : 02FFF0050000
 *   OUI data Mask: BC - 10111100
 *   Info Mask : 21 - Check for Band
 *   Capabilities: 40 - Band == 2G
 *
 * OUI 3 : 001018
 *   OUI data Len : 06
 *   OUI Data : 02FFF4050000
 *   OUI data Mask: BC - 10111100
 *   Info Mask : 21 - Check for Band
 *   Capabilities: 40 - Band == 2G
 *
 * This ini is used to specify the AP OUIs with which only 1x1 connection
 * with one Tx/Rx Chain is allowed.
 *
 * Related: gEnableActionOUI
 *
 * Supported Feature: Action OUIs
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ACTION_OUI_CONNECT_1X1_WITH_1_CHAIN CFG_INI_STRING( \
	 "gActionOUIConnect1x1with1TxRxChain", \
	 0, \
	 ACTION_OUI_MAX_STR_LEN, \
	 "001018 06 02FFF0040000 BC 21 40 001018 06 02FFF0050000 BC 21 40 001018 06 02FFF4050000 BC 21 40", \
	 "Used to specify action OUIs for 1x1 connection with one Tx/Rx Chain")

/*
 * <ini>
 * gActionOUIDisableAggressiveTX - Used to specify action OUIs to disable
 * Aggressive TX feature when operating in softap.
 *
 * @Default:
 * Note: User should strictly add new action OUIs at the end of this
 * default value.
 *
 * Default OUIs:
 *
 * OUI 1 : FFFFFF
 *   OUI data Len : 00
 *   OUI Data: No data
 *   OUI data Mask: No data mask
 *   Info Mask:  2A - Check for mac-addr, HT capability and Band
 *   Mac-addr: F8:59:71:00:00:00 - first 3 bytes
 *   Mac-mask: E0 - Match only first 3 bytes of peer mac-addr
 *   Capabilities: 50 – HT should be enabled, and band should be 2.4GHz
 *
 * OUI 2 : FFFFFF
 *   OUI data Len : 00
 *   OUI Data: No data
 *   OUI data Mask: No data mask
 *   Info Mask:  2A - Check for mac-addr, HT capability and Band
 *   Mac-addr: 14:AB:C5:00:00:00 - first 3 bytes
 *   Mac-mask: E0 - Match only first 3 bytes of peer mac-addr
 *   Capabilities: 50 – HT should be enabled, and band should be 2.4GHz
 *
 * When operating in Softap mode, this ini is used to specify
 * STA (peer) OUIs/mac-addr for which aggressive tx is disabled after
 * association is successful.
 *
 * Related: gEnableActionOUI
 *
 * Supported Feature: Action OUIs
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ACTION_OUI_DISABLE_AGGRESSIVE_TX CFG_INI_STRING( \
	"gActionOUIDisableAggressiveTX", \
	0, \
	ACTION_OUI_MAX_STR_LEN, \
	"FFFFFF 00 2A F85971000000 E0 50 FFFFFF 00 2A 14ABC5000000 E0 50", \
	"Used to specify action OUIs to disable aggressive TX")

 /* End of action oui inis */
#ifdef ENABLE_MTRACE_LOG
/*
 * <ini>
 * enable_mtrace - Enable Mtrace.
 * @Default: 0
 *
 * This ini is used to enable MTRACE logging
 *
 * Related: None.
 *
 * Supported Feature: MTRACE
 *
 * Usage: Internal/External
 *
 * </ini>
 */
#define CFG_ENABLE_MTRACE CFG_INI_BOOL( \
			"enable_mtrace", \
			false, \
			"Enable MTRACE")
#define CFG_ENABLE_MTRACE_ALL CFG(CFG_ENABLE_MTRACE)
#else
#define CFG_ENABLE_MTRACE_ALL
#endif

/*
 * <ini>
 * gEnableRTTsupport
 *
 * @Min: 0 - Disabled
 * @Max: 1 - Enabled
 * @Default: 1 - Enabled
 *
 * The param is used to enable/disable support for RTT
 *
 * Related: None.
 *
 * Supported Feature: RTT
 *
 * Usage: Internal/External
 *
 * </ini>
 */
#define CFG_ENABLE_RTT_SUPPORT CFG_INI_BOOL( \
		"gEnableRTTSupport", \
		1, \
		"The param is used to enable/disable support for RTT")

/*
 * <ini>
 * gAdvertiseConcurrentOperation - Iface combination advertising
 * @Min: 0
 * @Max: 1
 * @Default: 1
 *
 * This ini is used to control whether driver should indicate to kernel
 * wiphy layer the combination of all its interfaces' supportability.
 *
 * Related: None
 *
 * Supported Feature: STA
 *
 * Usage: Internal/External
 *
 * </ini>
 */
#define CFG_ADVERTISE_CONCURRENT_OPERATION CFG_INI_BOOL( \
		"gAdvertiseConcurrentOperation", \
		1, \
		"Iface combination advertising")

/*
 * <ini>
 * gEnableUnitTestFramework - Enable/Disable unit test framework
 * @Min: 0
 * @Max: 1
 * @Default: 0
 *
 * Related: None
 *
 * Supported Feature: unit test framework
 *
 * Usage: Internal (only for dev and test team)
 *
 * </ini>
 */
#define CFG_ENABLE_UNIT_TEST_FRAMEWORK CFG_INI_BOOL( \
			"gEnableUnitTestFramework", \
			0, \
			"Enable/Disable unit test framework")

/*
 * <ini>
 * gDisableChannel - Used to disable channels specified
 *
 * @Min: 0
 * @Max: 1
 * Default: 0
 *
 * This ini is used to disable the channels given in the command
 * SET_DISABLE_CHANNEL_LIST and to restore the channels when the
 * command is given with channel list as 0
 * Usage: External
 *
 * </ini>
 */
#define CFG_ENABLE_DISABLE_CHANNEL  CFG_INI_BOOL( \
			"gDisableChannel", \
			0, \
			"Enable/Disable to disable channels specified")

/*
 * <ini>
 * gSarVersion - Used to specify SAR version
 *
 * @Min: 1
 * @Max: 2
 * Default: 1
 *
 * This ini is used to specify the SAR feature version.
 * If value of this ini is set to 2, SAR version 2 will
 * be used.
 * Usage: External
 *
 * </ini>
 */
#define CFG_SAR_VERSION  CFG_INI_UINT( \
			"gSarVersion", \
			1, \
			2, \
			1, \
			CFG_VALUE_OR_DEFAULT, \
			"Specify the SAR version")

/*
 * <ini>
 * gDisableWow - Used to disable wow feature
 *
 * @Min: 0
 * @Max: 1
 * Default: 0
 *
 * This ini is used to disable wow feature for all modes
 * that means hlos platform suspend(cfg80211 suspend) will
 * be rejected by wifi kernel driver.
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_WOW_DISABLE  CFG_INI_UINT( \
			"gDisableWow", \
			0, \
			1, \
			0, \
			CFG_VALUE_OR_DEFAULT, \
			"Disable wow feature")

/**
 * enum host_log_level - Debug verbose level imposed by user
 * @HOST_LOG_LEVEL_NONE: no trace will be logged.
 * @HOST_LOG_LEVEL_FATAL: fatal error will be logged
 * @HOST_LOG_LEVEL_ERROR: error(include level less than error) will be logged
 * @HOST_LOG_LEVEL_WARN: warning(include level less than warning) will be logged
 * @HOST_LOG_LEVEL_INFO: inform(include level less than inform) will be logged
 * @HOST_LOG_LEVEL_DEBUG: debug(include level less than debug) will be logged
 * @HOST_LOG_LEVEL_TRACE: trace(include level less than trace) will be logged
 * @HOST_LOG_LEVEL_MAX: Max host log level
 */
enum host_log_level {
	HOST_LOG_LEVEL_NONE = 0,
	HOST_LOG_LEVEL_FATAL,
	HOST_LOG_LEVEL_ERROR,
	HOST_LOG_LEVEL_WARN,
	HOST_LOG_LEVEL_INFO,
	HOST_LOG_LEVEL_DEBUG,
	HOST_LOG_LEVEL_TRACE,
	HOST_LOG_LEVEL_MAX,
};

/*
 * <ini>
 * gHostModuleLoglevel - modulized host debug log level
 * @Min: N/A
 * @Max: N/A
 * @Default: N/A
 *
 * This ini is used to set modulized host debug log level.
 * WLAN host module log level input string format looks like below:
 * gHostModuleLoglevel="<host Module ID>,<Log Level>,..."
 * For example:
 * gHostModuleLoglevel=51,1,52,2,53,3,54,4,55,5,56,6
 * The above input string means:
 * For WLAN host module ID 51 enable log level HOST_LOG_LEVEL_FATAL
 * For WLAN host module ID 52 enable log level HOST_LOG_LEVEL_ERROR
 * For WLAN host module ID 53 enable log level HOST_LOG_LEVEL_WARN
 * For WLAN host module ID 54 enable log level HOST_LOG_LEVEL_INFO
 * For WLAN host module ID 55 enable log level HOST_LOG_LEVEL_DEBUG
 * For WLAN host module ID 55 enable log level HOST_LOG_LEVEL_TRACE
 * For valid values of module ids check enum QDF_MODULE_ID and
 * for valid values of log levels check below.
 * HOST_LOG_LEVEL_NONE = 0, No trace will be logged
 * HOST_LOG_LEVEL_FATAL = 1, fatal error log
 * HOST_LOG_LEVEL_ERROR = 2, error(include level less than error) log
 * HOST_LOG_LEVEL_WARN = 3, warning(include level less than warning) log
 * HOST_LOG_LEVEL_INFO = 4, inform(include level less than inform) log
 * HOST_LOG_LEVEL_DEBUG = 5, debug(include level less than debug) log
 * HOST_LOG_LEVEL_TRACE = 6, trace(include level less than trace) log
 *
 * Related: None
 *
 * Supported Feature: Debugging
 *
 * Usage: Internal
 *
 * </ini>
 */

#define HOST_MODULE_LOG_LEVEL_STRING_MAX_LENGTH  (QDF_MODULE_ID_MAX * 6)
#define CFG_ENABLE_HOST_MODULE_LOG_LEVEL CFG_INI_STRING( \
	"gHostModuleLoglevel", \
	0, \
	HOST_MODULE_LOG_LEVEL_STRING_MAX_LENGTH, \
	"", \
	"Set modulized host debug log level")

/*
 * <ini>
 * gActionOUIForceMaxNss - Used to specify action OUIs for Max NSS connection
 * @Default:
 * Note: User should strictly add new action OUIs at the end of this
 * default value.
 *
 * Default OUIs: (All values in Hex)
 * OUI 1 :001018
 *   OUI data Len : 06
 *   OUI Data : 0201009c0000
 *   OUI data Mask: FC
 *   Info Mask : 01 - only OUI present in Info mask
 * OUI 2 :001018
 *   OUI data Len : 06
 *   OUI Data : 0201001c0000
 *   OUI data Mask: FC
 *   Info Mask : 01 - only OUI present in Info mask
 * OUI 3 :001018
 *   OUI data Len : 06
 *   OUI Data : 0200009c0000
 *   OUI data Mask: FC
 *   Info Mask : 01 - only OUI present in Info mask
 *
 * This ini is used to specify the AP OUIs with which max capability is
 * sent in association request even though AP advertises 1x1 capability.
 *
 * Related: None
 *
 * Supported Feature: Action OUIs
 *
 * Usage: External
 *
 * </ini>
 */
#define CFG_ACTION_OUI_FORCE_MAX_NSS CFG_INI_STRING( \
			"gActionOUIForceMaxNss", \
			0, \
			ACTION_OUI_MAX_STR_LEN, \
			"001018 06 0201009c0000 FC 01 001018 06 0201001c0000 FC 01 001018 06 0200009c0000 FC 01", \
			"Used to specify action OUIs for forcing max NSS connection")

#define CFG_HDD_ALL \
	CFG_ENABLE_PACKET_LOG_ALL \
	CFG_ENABLE_RUNTIME_PM_ALL \
	CFG_VC_MODE_BITMAP_ALL \
	CFG_WLAN_AUTO_SHUTDOWN_ALL \
	CFG_WLAN_LOGGING_SUPPORT_ALL \
	CFG(CFG_ACTION_OUI_CCKM_1X1) \
	CFG(CFG_ACTION_OUI_CONNECT_1X1) \
	CFG(CFG_ACTION_OUI_CONNECT_1X1_WITH_1_CHAIN) \
	CFG(CFG_ACTION_OUI_ITO_ALTERNATE) \
	CFG(CFG_ACTION_OUI_ITO_EXTENSION) \
	CFG(CFG_ACTION_OUI_DISABLE_AGGRESSIVE_TX) \
	CFG(CFG_ACTION_OUI_FORCE_MAX_NSS) \
	CFG(CFG_ACTION_OUI_SWITCH_TO_11N_MODE) \
	CFG(CFG_ADVERTISE_CONCURRENT_OPERATION) \
	CFG(CFG_BUG_ON_REINIT_FAILURE) \
	CFG(CFG_DBS_SCAN_SELECTION) \
	CFG(CFG_DERIVED_INTERFACE_POOL) \
	CFG(CFG_ENABLE_CONCURRENT_STA) \
	CFG(CFG_ENABLE_ACTION_OUI) \
	CFG(CFG_ENABLE_FW_LOG) \
	CFG(CFG_ENABLE_FW_UART_PRINT) \
	CFG(CFG_ENABLE_MAC_PROVISION) \
	CFG_ENABLE_MTRACE_ALL \
	CFG(CFG_ENABLE_RAMDUMP_COLLECTION) \
	CFG(CFG_ENABLE_RTT_SUPPORT) \
	CFG(CFG_ENABLE_UNIT_TEST_FRAMEWORK) \
	CFG(CFG_INTERFACE_CHANGE_WAIT) \
	CFG(CFG_INFORM_BSS_RSSI_RAW) \
	CFG(CFG_MULTICAST_HOST_FW_MSGS) \
	CFG(CFG_NUM_VDEV_ENABLE) \
	CFG(CFG_OPERATING_CHANNEL) \
	CFG(CFG_PRIVATE_WEXT_CONTROL) \
	CFG(CFG_PROVISION_INTERFACE_POOL) \
	CFG(CFG_TIMER_MULTIPLIER) \
	CFG(CFG_HDD_DOT11_MODE) \
	CFG(CFG_ENABLE_DISABLE_CHANNEL) \
	CFG(CFG_SAR_VERSION) \
	CFG(CFG_WOW_DISABLE) \
	CFG(CFG_ENABLE_HOST_MODULE_LOG_LEVEL)
#endif