| ########################## Start of libnfc-nci.conf ########################### |
| ############################################################################### |
| # Application options |
| NFC_DEBUG_ENABLED=1 |
| ############################################################################### |
| # performance measurement |
| # Change this setting to control how often USERIAL log the performance (throughput) |
| # data on read/write/poll |
| # defailt is to log performance dara for every 100 read or write |
| #REPORT_PERFORMANCE_MEASURE=100 |
| ############################################################################### |
| # File used for NFA storage |
| NFA_STORAGE="/data/nfc" |
| ############################################################################### |
| # Configure the default NfcA/IsoDep techology and protocol route. Can be |
| # either a secure element (e.g. 0xF4) or the host (0x00) |
| #DEFAULT_ISODEP_ROUTE=0x00 |
| |
| |
| ############################################################################### |
| # Force UICC to only listen to the following technology(s). |
| # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. |
| # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F |
| UICC_LISTEN_TECH_MASK=0x07 |
| |
| ############################################################################### |
| # Force HOST listen feature enable or disable. |
| # 0: Disable |
| # 1: Enable |
| HOST_LISTEN_ENABLE=0x01 |
| ############################################################################### |
| # When screen is turned off, specify the desired power state of the controller. |
| # 0: power-off-sleep state; DEFAULT |
| # 1: full-power state |
| # 2: screen-off card-emulation (CE4/CE3/CE1 modes are used) |
| SCREEN_OFF_POWER_STATE=1 |
| ############################################################################### |
| # Force tag polling for the following technology(s). |
| # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. |
| # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | |
| # NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 | |
| # NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO | |
| # NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE. |
| # |
| # Notable bits: |
| # NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ |
| # NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */ |
| # NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ |
| # NFA_TECHNOLOGY_MASK_ISO15693 0x08 /* Proprietary Technology */ |
| # NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */ |
| # NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */ |
| # NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */ |
| POLLING_TECH_MASK=0x6F |
| ############################################################################### |
| # Force P2P to only listen for the following technology(s). |
| # The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. |
| # Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F | |
| # NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE |
| # |
| # Notable bits: |
| # NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ |
| # NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ |
| # NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */ |
| # NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */ |
| P2P_LISTEN_TECH_MASK=0x45 |
| ############################################################################### |
| PRESERVE_STORAGE=0x01 |
| ############################################################################### |
| # Override the stack default for NFA_EE_MAX_EE_SUPPORTED set in nfc_target.h. |
| # The value is set to 3 by default as it assumes we will discover 0xF2, |
| # 0xF3, and 0xF4. If a platform will exclude and SE, this value can be reduced |
| # so that the stack will not wait any longer than necessary. |
| |
| # Maximum EE supported number |
| # NXP PN547C2 0x02 |
| # NXP PN65T 0x03 |
| # NXP PN548C2 0x02 |
| # NXP PN66T 0x03 |
| NFA_MAX_EE_SUPPORTED=0x03 |
| ############################################################################## |
| # Deactivate notification wait time out in seconds used in ETSI Reader mode |
| # 0 - Infinite wait |
| NFA_DM_DISC_NTF_TIMEOUT=100 |
| |
| ############################################################################### |
| # AID_MATCHING constants |
| # AID_MATCHING_EXACT_ONLY 0x00 |
| # AID_MATCHING_EXACT_OR_PREFIX 0x01 |
| # AID_MATCHING_PREFIX_ONLY 0x02 |
| #AID_MATCHING_EXACT_OR_SUBSET_OR_PREFIX 0x03 |
| AID_MATCHING_MODE=0x03 |
| ############################################################################### |
| # Preferred Secure Element for Technology based routing |
| # eSE 0x01 |
| # UICC 0x02 |
| |
| NXP_PRFD_TECH_SE=0x01 |
| |
| ################################################################################ |
| #Set bit to 1 , black list is enabled |
| #Set bit to 0, to disable balcklist |
| NFA_AID_BLOCK_ROUTE=0x00 |
| |
| ################################################################################ |
| # Maximum WTX requests entertained by MW |
| NXP_WM_MAX_WTX_COUNT=50 |
| ################################################################################ |
| #Set the default Felica T3T System Code : |
| #This settings will be used when application does not set this parameter |
| DEFAULT_SYS_CODE={FE:FF} |
| ######################################################################### |