| # This file allows user to override the factory |
| # defaults for the WLAN Driver |
| |
| # Enable IMPS or not |
| gEnableImps=1 |
| |
| # Enable/Disable Idle Scan |
| gEnableIdleScan=0 |
| |
| # Increase sleep duration (seconds) during IMPS |
| # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
| # unnecessary if Idle Scan is disabled. |
| gImpsModSleepTime=0 |
| |
| # Enable BMPS or not |
| gEnableBmps=1 |
| |
| # Enable Close Loop or not |
| gEnableCloseLoop=1 |
| |
| # Enable suspend or not |
| # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| gEnableSuspend=3 |
| |
| # Phy Mode (auto, b, g, n, etc) |
| gDot11Mode=0 |
| |
| # Handoff Enable(1) Disable(0) |
| gEnableHandoff=0 |
| |
| # CSR Roaming Enable(1) Disable(0) |
| gRoamingTime=0 |
| |
| # Assigned MAC Addresses - This will be used until NV items are in place |
| # Each byte of MAC address is represented in Hex format as XX |
| Intf0MacAddress=000AF58989FF |
| Intf1MacAddress=000AF58989FE |
| Intf2MacAddress=000AF58989FD |
| Intf3MacAddress=000AF58989FC |
| |
| # UAPSD service interval for VO,VI, BE, BK traffic |
| InfraUapsdVoSrvIntv=0 |
| InfraUapsdViSrvIntv=0 |
| InfraUapsdBeSrvIntv=0 |
| InfraUapsdBkSrvIntv=0 |
| |
| # Disable RSSI FW filtering |
| gEnableFWRssiMonitoring=0 |
| |
| # Make 1x1 the default antenna configuration |
| gNumRxAnt=1 |
| |
| # Beacon filtering frequency (unit in beacon intervals) |
| gNthBeaconFilter=50 |
| |
| # Enable WAPI or not |
| # WAPIIsEnabled=0 |
| |
| # Flags to filter Mcast abd Bcast RX packets. |
| # Value 0: No filtering, 1: Filter all Multicast. |
| # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast |
| McastBcastFilter=3 |
| |
| #Flag to enable HostARPOffload feature or not |
| hostArpOffload=0 |
| |
| #SoftAP Related Parameters |
| # AP MAc addr |
| gAPMacAddr=000AF58989EF |
| |
| # 802.11n Protection flag |
| gEnableApProt=1 |
| |
| #Enable OBSS protection |
| gEnableApOBSSProt=0 |
| |
| #Enable/Disable UAPSD for SoftAP |
| gEnableApUapsd=1 |
| |
| # Fixed Rate |
| gFixedRate=0 |
| |
| # Maximum Tx power |
| # gTxPowerCap=30 |
| |
| # Fragmentation Threshold |
| # gFragmentationThreshold=2346 |
| |
| # RTS threshold |
| RTSThreshold=2347 |
| |
| # Intra-BSS forward |
| gDisableIntraBssFwd=0 |
| |
| # WMM Enable/Disable |
| WmmIsEnabled=0 |
| |
| # 802.11d support |
| g11dSupportEnabled=1 |
| |
| # CCX Support and fast transition |
| CcxEnabled=0 |
| FastTransitionEnabled=0 |
| ImplicitQosIsEnabled=1 |
| gNeighborScanTimerPeriod=200 |
| |
| gNeighborLookupThreshold=50 |
| gNeighborReassocThreshold=55 |
| |
| gNeighborScanChannelList=1,11,36,64 |
| gNeighborScanChannelMinTime=20 |
| gNeighborScanChannelMaxTime=30 |
| gMaxNeighborReqTries=3 |
| |
| # SAP Country code |
| # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| # Example |
| # US Indoor, USI |
| # Korea Outdoor, KRO |
| # Japan without optional byte, JP |
| # France without optional byte, FR |
| #gAPCntryCode=USI |
| |
| #Short Guard Interval Enable/disable |
| gShortGI20Mhz=1 |
| gShortGI40Mhz=1 |
| |
| #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| gAPAutoShutOff=0 |
| |
| # SAP auto channel selection configuration |
| # 0 = disable auto channel selection |
| # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| gApAutoChannelSelection=0 |
| |
| # Listen Energy Detect Mode Configuration |
| # Valid values 0-128 |
| # 128 means disable Energy Detect feature |
| # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. |
| # 10-128 are reserved. |
| # The EDET threshold mapping is as follows in 3dB step: |
| # 0 = -60 dBm |
| # 1 = -63 dBm |
| # 2 = -66 dBm |
| # ... |
| # 7 = -81 dBm |
| # 8 = -84 dBm |
| # 9 = -87 dBm |
| # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: |
| # |
| # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. |
| # |
| gEnablePhyAgcListenMode=128 |
| |
| #Preferred band (both or 2.4 only or 5 only) |
| BandCapability=0 |
| |
| #Forced Device Listen Interval in multiples of DTIM Period aligned to DTIM |
| gEnableModulatedDTIM=3 |
| |
| #Beacon Early Termination (1 = enable the BET feature, 0 = disable) |
| enableBeaconEarlyTermination=1 |
| beaconEarlyTerminationWakeInterval=11 |
| |
| #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) |
| gEnableBtAmp=0 |
| |
| #Preferred channel to start BT AMP AP mode (0 means, any channel) |
| BtAmpPreferredChannel=0 |
| |
| #SOFTAP Channel Range selection |
| gAPChannelSelectStartChannel=1 |
| gAPChannelSelectEndChannel=11 |
| |
| #SOFTAP Channel Range selection Operating band |
| # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND |
| gAPChannelSelectOperatingBand=0 |
| |
| #Enable Keep alive with non-zero period value |
| gStaKeepAlivePeriod = 25 |
| |
| #If set will start with active scan after driver load, otherwise will start with |
| #passive scan to find out the domain |
| gEnableBypass11d=1 |
| |
| #If set to 0, will not scan DFS channels |
| gEnableDFSChnlScan=0 |
| |
| # Enable logp/SSR |
| gEnableLogp=1 |
| |
| # Disable HT40 |
| gChannelBondingMode5GHz=0 |
| |
| # Enable Automatic Tx Power control |
| gEnableAutomaticTxPowerControl=1 |
| |
| # Derive P2P MAC address from primary MAC address |
| isP2pDeviceAddrAdministrated=1 |
| |
| END |
| # Note: Configuration parser would not read anything past the END marker |