Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 1 | # This file allows user to override the factory |
| 2 | # defaults for the WLAN Driver |
| 3 | |
| 4 | # Enable IMPS or not |
| 5 | gEnableImps=1 |
| 6 | |
| 7 | # Enable/Disable Idle Scan |
| 8 | gEnableIdleScan=0 |
| 9 | |
| 10 | # Increase sleep duration (seconds) during IMPS |
Jeff Johnson | dcf8781 | 2012-10-12 00:37:27 -0700 | [diff] [blame] | 11 | # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 12 | # unnecessary if Idle Scan is disabled. |
| 13 | gImpsModSleepTime=0 |
| 14 | |
| 15 | # Enable BMPS or not |
| 16 | gEnableBmps=1 |
| 17 | |
bill.jung | cf53439 | 2012-07-24 20:02:34 +0900 | [diff] [blame] | 18 | # Enable Close Loop or not |
| 19 | gEnableCloseLoop=1 |
| 20 | |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 21 | # Enable suspend or not |
| 22 | # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| 23 | gEnableSuspend=3 |
| 24 | |
| 25 | # Phy Mode (auto, b, g, n, etc) |
| 26 | gDot11Mode=0 |
| 27 | |
| 28 | # Handoff Enable(1) Disable(0) |
| 29 | gEnableHandoff=0 |
| 30 | |
| 31 | # CSR Roaming Enable(1) Disable(0) |
| 32 | gRoamingTime=0 |
| 33 | |
| 34 | # Assigned MAC Addresses - This will be used until NV items are in place |
| 35 | # Each byte of MAC address is represented in Hex format as XX |
| 36 | Intf0MacAddress=000AF58989FF |
| 37 | Intf1MacAddress=000AF58989FE |
| 38 | Intf2MacAddress=000AF58989FD |
| 39 | Intf3MacAddress=000AF58989FC |
| 40 | |
| 41 | # UAPSD service interval for VO,VI, BE, BK traffic |
| 42 | InfraUapsdVoSrvIntv=0 |
| 43 | InfraUapsdViSrvIntv=0 |
| 44 | InfraUapsdBeSrvIntv=0 |
| 45 | InfraUapsdBkSrvIntv=0 |
| 46 | |
Iliyan Malchev | 974dfab | 2012-10-31 09:12:44 -0700 | [diff] [blame] | 47 | # Enable Firmware RSSI monitoring for roaming |
| 48 | gEnableFWRssiMonitoring=1 |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 49 | |
| 50 | # Make 1x1 the default antenna configuration |
| 51 | gNumRxAnt=1 |
| 52 | |
| 53 | # Beacon filtering frequency (unit in beacon intervals) |
| 54 | gNthBeaconFilter=50 |
| 55 | |
| 56 | # Enable WAPI or not |
| 57 | # WAPIIsEnabled=0 |
| 58 | |
Jeff Johnson | dcf8781 | 2012-10-12 00:37:27 -0700 | [diff] [blame] | 59 | # Flags to filter Mcast and Bcast RX packets. |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 60 | # Value 0: No filtering, 1: Filter all Multicast. |
Jeff Johnson | dcf8781 | 2012-10-12 00:37:27 -0700 | [diff] [blame] | 61 | # 2: Filter all Broadcast. 3: Filter all Mcast and Bcast |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 62 | McastBcastFilter=3 |
| 63 | |
| 64 | #Flag to enable HostARPOffload feature or not |
| 65 | hostArpOffload=0 |
| 66 | |
| 67 | #SoftAP Related Parameters |
Jeff Johnson | c3cb630 | 2012-10-12 17:16:27 -0700 | [diff] [blame] | 68 | # AP MAc addr (obsolete) |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 69 | gAPMacAddr=000AF58989EF |
| 70 | |
Jeff Johnson | c3cb630 | 2012-10-12 17:16:27 -0700 | [diff] [blame] | 71 | # Enable Random BSSID |
| 72 | gEnableApRandomBssid=1 |
| 73 | |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 74 | # 802.11n Protection flag |
| 75 | gEnableApProt=1 |
| 76 | |
Jeff Johnson | c3cb630 | 2012-10-12 17:16:27 -0700 | [diff] [blame] | 77 | # Enable OBSS protection |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 78 | gEnableApOBSSProt=0 |
| 79 | |
Jeff Johnson | c3cb630 | 2012-10-12 17:16:27 -0700 | [diff] [blame] | 80 | # Enable/Disable UAPSD for SoftAP |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 81 | gEnableApUapsd=1 |
| 82 | |
| 83 | # Fixed Rate |
| 84 | gFixedRate=0 |
| 85 | |
| 86 | # Maximum Tx power |
| 87 | # gTxPowerCap=30 |
| 88 | |
| 89 | # Fragmentation Threshold |
| 90 | # gFragmentationThreshold=2346 |
| 91 | |
| 92 | # RTS threshold |
| 93 | RTSThreshold=2347 |
| 94 | |
| 95 | # Intra-BSS forward |
| 96 | gDisableIntraBssFwd=0 |
| 97 | |
| 98 | # WMM Enable/Disable |
| 99 | WmmIsEnabled=0 |
| 100 | |
| 101 | # 802.11d support |
| 102 | g11dSupportEnabled=1 |
| 103 | |
| 104 | # CCX Support and fast transition |
| 105 | CcxEnabled=0 |
Iliyan Malchev | 974dfab | 2012-10-31 09:12:44 -0700 | [diff] [blame] | 106 | FastTransitionEnabled=1 |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 107 | ImplicitQosIsEnabled=1 |
| 108 | gNeighborScanTimerPeriod=200 |
| 109 | |
Iliyan Malchev | 974dfab | 2012-10-31 09:12:44 -0700 | [diff] [blame] | 110 | gNeighborLookupThreshold=76 |
| 111 | gNeighborReassocThreshold=81 |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 112 | |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 113 | gNeighborScanChannelMinTime=20 |
| 114 | gNeighborScanChannelMaxTime=30 |
| 115 | gMaxNeighborReqTries=3 |
| 116 | |
Iliyan Malchev | 974dfab | 2012-10-31 09:12:44 -0700 | [diff] [blame] | 117 | # Legacy (non-CCX, non-802.11r) Fast Roaming Support |
| 118 | # To enable, set FastRoamEnabled=1, gEnableFWRssiMonitoring=1, FastTransitionEnabled=1 |
| 119 | # To disable, set FastRoamEnabled=0, gEnableFWRssiMonitoring=0, FastTransitionEnabled=0 |
| 120 | FastRoamEnabled=1 |
| 121 | |
| 122 | #Check if the AP to which we are roaming is better than current AP in terms of RSSI. |
| 123 | #Checking is disabled if set to Zero.Otherwise it will use this value as to how better |
| 124 | #the RSSI of the new/roamable AP should be for roaming |
| 125 | RoamRssiDiff=3 |
| 126 | |
| 127 | #Configure the RSSI gap that will be used to partition/categorize width of |
| 128 | #each individual category (aka bucket). |
| 129 | gRssiCatGap=5 |
Jeff Johnson | dcf8781 | 2012-10-12 00:37:27 -0700 | [diff] [blame] | 130 | |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 131 | # SAP Country code |
| 132 | # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| 133 | # Example |
| 134 | # US Indoor, USI |
| 135 | # Korea Outdoor, KRO |
| 136 | # Japan without optional byte, JP |
| 137 | # France without optional byte, FR |
| 138 | #gAPCntryCode=USI |
| 139 | |
| 140 | #Short Guard Interval Enable/disable |
| 141 | gShortGI20Mhz=1 |
| 142 | gShortGI40Mhz=1 |
| 143 | |
| 144 | #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| 145 | gAPAutoShutOff=0 |
| 146 | |
| 147 | # SAP auto channel selection configuration |
| 148 | # 0 = disable auto channel selection |
| 149 | # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| 150 | gApAutoChannelSelection=0 |
| 151 | |
| 152 | # Listen Energy Detect Mode Configuration |
| 153 | # Valid values 0-128 |
| 154 | # 128 means disable Energy Detect feature |
| 155 | # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. |
| 156 | # 10-128 are reserved. |
| 157 | # The EDET threshold mapping is as follows in 3dB step: |
| 158 | # 0 = -60 dBm |
| 159 | # 1 = -63 dBm |
| 160 | # 2 = -66 dBm |
| 161 | # ... |
| 162 | # 7 = -81 dBm |
| 163 | # 8 = -84 dBm |
| 164 | # 9 = -87 dBm |
| 165 | # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: |
| 166 | # |
| 167 | # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. |
| 168 | # |
| 169 | gEnablePhyAgcListenMode=128 |
| 170 | |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 171 | #Preferred band (both or 2.4 only or 5 only) |
| 172 | BandCapability=0 |
| 173 | |
Jeff Johnson | 64eb138 | 2012-09-22 17:38:03 -0700 | [diff] [blame] | 174 | #Forced Device Listen Interval in multiples of DTIM Period aligned to DTIM |
| 175 | gEnableModulatedDTIM=3 |
| 176 | |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 177 | #Beacon Early Termination (1 = enable the BET feature, 0 = disable) |
Jeff Johnson | 64eb138 | 2012-09-22 17:38:03 -0700 | [diff] [blame] | 178 | enableBeaconEarlyTermination=1 |
| 179 | beaconEarlyTerminationWakeInterval=11 |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 180 | |
| 181 | #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) |
Jeff Johnson | 64eb138 | 2012-09-22 17:38:03 -0700 | [diff] [blame] | 182 | gEnableBtAmp=0 |
| 183 | |
| 184 | #Preferred channel to start BT AMP AP mode (0 means, any channel) |
| 185 | BtAmpPreferredChannel=0 |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 186 | |
Jeff Johnson | dcf8781 | 2012-10-12 00:37:27 -0700 | [diff] [blame] | 187 | #SOFTAP Channel Range selection |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 188 | gAPChannelSelectStartChannel=1 |
| 189 | gAPChannelSelectEndChannel=11 |
| 190 | |
| 191 | #SOFTAP Channel Range selection Operating band |
| 192 | # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND |
| 193 | gAPChannelSelectOperatingBand=0 |
| 194 | |
| 195 | #Enable Keep alive with non-zero period value |
bill.jung | ca73d4a | 2012-09-04 16:26:25 +0900 | [diff] [blame] | 196 | gStaKeepAlivePeriod = 25 |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 197 | |
| 198 | #If set will start with active scan after driver load, otherwise will start with |
| 199 | #passive scan to find out the domain |
| 200 | gEnableBypass11d=1 |
| 201 | |
| 202 | #If set to 0, will not scan DFS channels |
Jeff Johnson | 64eb138 | 2012-09-22 17:38:03 -0700 | [diff] [blame] | 203 | gEnableDFSChnlScan=0 |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 204 | |
| 205 | # Enable logp/SSR |
| 206 | gEnableLogp=1 |
| 207 | |
bill.jung | ca73d4a | 2012-09-04 16:26:25 +0900 | [diff] [blame] | 208 | # Disable HT40 |
| 209 | gChannelBondingMode5GHz=0 |
| 210 | |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 211 | # Enable Automatic Tx Power control |
| 212 | gEnableAutomaticTxPowerControl=1 |
Jeff Johnson | dd4b6aa | 2012-08-23 22:22:12 -0700 | [diff] [blame] | 213 | |
| 214 | # Derive P2P MAC address from primary MAC address |
| 215 | isP2pDeviceAddrAdministrated=1 |
| 216 | |
Jeff Johnson | 54405bd | 2012-11-05 12:24:49 -0800 | [diff] [blame] | 217 | # Disable channel 165 for Indonesia |
| 218 | gIgnore_Chan165=1 |
| 219 | |
Iliyan Malchev | fefe23c | 2012-06-08 10:36:25 -0700 | [diff] [blame] | 220 | END |
| 221 | # Note: Configuration parser would not read anything past the END marker |