drivers/usb/otg/msm_otg.c - fp2-dev/kernel/msm - Gitiles

 /* Copyright (c) 2009-2013, Linux Foundation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 and
  * only version 2 as published by the Free Software Foundation.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  */

 #include <linux/module.h>
 #include <linux/device.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/slab.h>
 #include <linux/interrupt.h>
 #include <linux/err.h>
 #include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/ioport.h>
 #include <linux/uaccess.h>
 #include <linux/debugfs.h>
 #include <linux/seq_file.h>
 #include <linux/pm_runtime.h>
 #include <linux/of.h>
 #include <linux/dma-mapping.h>

 #include <linux/usb.h>
 #include <linux/usb/otg.h>
 #include <linux/usb/ulpi.h>
 #include <linux/usb/gadget.h>
 #include <linux/usb/hcd.h>
 #include <linux/usb/quirks.h>
 #include <linux/usb/msm_hsusb.h>
 #include <linux/usb/msm_hsusb_hw.h>
 #include <linux/usb/msm_ext_chg.h>
 #include <linux/regulator/consumer.h>
 #include <linux/mfd/pm8xxx/pm8921-charger.h>
 #include <linux/mfd/pm8xxx/misc.h>
 #include <linux/mhl_8334.h>

 #include <mach/scm.h>
 #include <mach/clk.h>
 #include <mach/mpm.h>
 #include <mach/msm_xo.h>
 #include <mach/msm_bus.h>
 #include <mach/rpm-regulator.h>

 #define MSM_USB_BASE	(motg->regs)
 #define DRIVER_NAME	"msm_otg"

 #define ID_TIMER_FREQ		(jiffies + msecs_to_jiffies(500))
 #define CHG_RECHECK_DELAY	(jiffies + msecs_to_jiffies(2000))
 #define ULPI_IO_TIMEOUT_USEC	(10 * 1000)
 #define USB_PHY_3P3_VOL_MIN	3050000 /* uV */
 #define USB_PHY_3P3_VOL_MAX	3300000 /* uV */
 #define USB_PHY_3P3_HPM_LOAD	50000	/* uA */
 #define USB_PHY_3P3_LPM_LOAD	4000	/* uA */

 #define USB_PHY_1P8_VOL_MIN	1800000 /* uV */
 #define USB_PHY_1P8_VOL_MAX	1800000 /* uV */
 #define USB_PHY_1P8_HPM_LOAD	50000	/* uA */
 #define USB_PHY_1P8_LPM_LOAD	4000	/* uA */

 #define USB_PHY_VDD_DIG_VOL_NONE	0 /*uV */
 #define USB_PHY_VDD_DIG_VOL_MIN	1045000 /* uV */
 #define USB_PHY_VDD_DIG_VOL_MAX	1320000 /* uV */

 #define USB_SUSPEND_DELAY_TIME	(500 * HZ/1000) /* 500 msec */

 enum msm_otg_phy_reg_mode {
 	USB_PHY_REG_OFF,
 	USB_PHY_REG_ON,
 	USB_PHY_REG_LPM_ON,
 	USB_PHY_REG_LPM_OFF,
 };

 static char *override_phy_init;
 module_param(override_phy_init, charp, S_IRUGO|S_IWUSR);
 MODULE_PARM_DESC(override_phy_init,
 	"Override HSUSB PHY Init Settings");

 unsigned int lpm_disconnect_thresh = 1000;
 module_param(lpm_disconnect_thresh , uint, S_IRUGO | S_IWUSR);
 MODULE_PARM_DESC(lpm_disconnect_thresh,
 	"Delay before entering LPM on USB disconnect");

 static bool floated_charger_enable;
 module_param(floated_charger_enable , bool, S_IRUGO | S_IWUSR);
 MODULE_PARM_DESC(floated_charger_enable,
 	"Whether to enable floated charger");

 static DECLARE_COMPLETION(pmic_vbus_init);
 static struct msm_otg *the_msm_otg;
 static bool debug_aca_enabled;
 static bool debug_bus_voting_enabled;
 static bool mhl_det_in_progress;

 static struct regulator *hsusb_3p3;
 static struct regulator *hsusb_1p8;
 static struct regulator *hsusb_vdd;
 static struct regulator *vbus_otg;
 static struct regulator *mhl_usb_hs_switch;
 static struct power_supply *psy;

 static bool aca_id_turned_on;
 static bool legacy_power_supply;
 static inline bool aca_enabled(void)
 {
 #ifdef CONFIG_USB_MSM_ACA
 	return true;
 #else
 	return debug_aca_enabled;
 #endif
 }

 static int vdd_val[VDD_TYPE_MAX][VDD_VAL_MAX] = {
 		{  /* VDD_CX CORNER Voting */
 			[VDD_NONE]	= RPM_VREG_CORNER_NONE,
 			[VDD_MIN]	= RPM_VREG_CORNER_NOMINAL,
 			[VDD_MAX]	= RPM_VREG_CORNER_HIGH,
 		},
 		{ /* VDD_CX Voltage Voting */
 			[VDD_NONE]	= USB_PHY_VDD_DIG_VOL_NONE,
 			[VDD_MIN]	= USB_PHY_VDD_DIG_VOL_MIN,
 			[VDD_MAX]	= USB_PHY_VDD_DIG_VOL_MAX,
 		},
 };

 static int msm_hsusb_ldo_init(struct msm_otg *motg, int init)
 {
 	int rc = 0;

 	if (init) {
 		hsusb_3p3 = devm_regulator_get(motg->phy.dev, "HSUSB_3p3");
 		if (IS_ERR(hsusb_3p3)) {
 			dev_err(motg->phy.dev, "unable to get hsusb 3p3\n");
 			return PTR_ERR(hsusb_3p3);
 		}

 		rc = regulator_set_voltage(hsusb_3p3, USB_PHY_3P3_VOL_MIN,
 				USB_PHY_3P3_VOL_MAX);
 		if (rc) {
 			dev_err(motg->phy.dev, "unable to set voltage level for"
 					"hsusb 3p3\n");
 			return rc;
 		}
 		hsusb_1p8 = devm_regulator_get(motg->phy.dev, "HSUSB_1p8");
 		if (IS_ERR(hsusb_1p8)) {
 			dev_err(motg->phy.dev, "unable to get hsusb 1p8\n");
 			rc = PTR_ERR(hsusb_1p8);
 			goto put_3p3_lpm;
 		}
 		rc = regulator_set_voltage(hsusb_1p8, USB_PHY_1P8_VOL_MIN,
 				USB_PHY_1P8_VOL_MAX);
 		if (rc) {
 			dev_err(motg->phy.dev, "unable to set voltage level "
 					"for hsusb 1p8\n");
 			goto put_1p8;
 		}

 		return 0;
 	}

 put_1p8:
 	regulator_set_voltage(hsusb_1p8, 0, USB_PHY_1P8_VOL_MAX);
 put_3p3_lpm:
 	regulator_set_voltage(hsusb_3p3, 0, USB_PHY_3P3_VOL_MAX);
 	return rc;
 }

 static int msm_hsusb_config_vddcx(int high)
 {
 	struct msm_otg *motg = the_msm_otg;
 	enum usb_vdd_type vdd_type = motg->vdd_type;
 	int max_vol = vdd_val[vdd_type][VDD_MAX];
 	int min_vol;
 	int ret;

 	min_vol = vdd_val[vdd_type][!!high];
 	ret = regulator_set_voltage(hsusb_vdd, min_vol, max_vol);
 	if (ret) {
 		pr_err("%s: unable to set the voltage for regulator "
 			"HSUSB_VDDCX\n", __func__);
 		return ret;
 	}

 	pr_debug("%s: min_vol:%d max_vol:%d\n", __func__, min_vol, max_vol);

 	return ret;
 }

 static int msm_hsusb_ldo_enable(struct msm_otg *motg,
 	enum msm_otg_phy_reg_mode mode)
 {
 	int ret = 0;

 	if (IS_ERR(hsusb_1p8)) {
 		pr_err("%s: HSUSB_1p8 is not initialized\n", __func__);
 		return -ENODEV;
 	}

 	if (IS_ERR(hsusb_3p3)) {
 		pr_err("%s: HSUSB_3p3 is not initialized\n", __func__);
 		return -ENODEV;
 	}

 	switch (mode) {
 	case USB_PHY_REG_ON:
 		ret = regulator_set_optimum_mode(hsusb_1p8,
 				USB_PHY_1P8_HPM_LOAD);
 		if (ret < 0) {
 			pr_err("%s: Unable to set HPM of the regulator "
 				"HSUSB_1p8\n", __func__);
 			return ret;
 		}

 		ret = regulator_enable(hsusb_1p8);
 		if (ret) {
 			dev_err(motg->phy.dev, "%s: unable to enable the hsusb 1p8\n",
 				__func__);
 			regulator_set_optimum_mode(hsusb_1p8, 0);
 			return ret;
 		}

 		ret = regulator_set_optimum_mode(hsusb_3p3,
 				USB_PHY_3P3_HPM_LOAD);
 		if (ret < 0) {
 			pr_err("%s: Unable to set HPM of the regulator "
 				"HSUSB_3p3\n", __func__);
 			regulator_set_optimum_mode(hsusb_1p8, 0);
 			regulator_disable(hsusb_1p8);
 			return ret;
 		}

 		ret = regulator_enable(hsusb_3p3);
 		if (ret) {
 			dev_err(motg->phy.dev, "%s: unable to enable the hsusb 3p3\n",
 				__func__);
 			regulator_set_optimum_mode(hsusb_3p3, 0);
 			regulator_set_optimum_mode(hsusb_1p8, 0);
 			regulator_disable(hsusb_1p8);
 			return ret;
 		}

 		break;

 	case USB_PHY_REG_OFF:
 		ret = regulator_disable(hsusb_1p8);
 		if (ret) {
 			dev_err(motg->phy.dev, "%s: unable to disable the hsusb 1p8\n",
 				__func__);
 			return ret;
 		}

 		ret = regulator_set_optimum_mode(hsusb_1p8, 0);
 		if (ret < 0)
 			pr_err("%s: Unable to set LPM of the regulator "
 				"HSUSB_1p8\n", __func__);

 		ret = regulator_disable(hsusb_3p3);
 		if (ret) {
 			dev_err(motg->phy.dev, "%s: unable to disable the hsusb 3p3\n",
 				 __func__);
 			return ret;
 		}
 		ret = regulator_set_optimum_mode(hsusb_3p3, 0);
 		if (ret < 0)
 			pr_err("%s: Unable to set LPM of the regulator "
 				"HSUSB_3p3\n", __func__);

 		break;

 	case USB_PHY_REG_LPM_ON:
 		ret = regulator_set_optimum_mode(hsusb_1p8,
 				USB_PHY_1P8_LPM_LOAD);
 		if (ret < 0) {
 			pr_err("%s: Unable to set LPM of the regulator: HSUSB_1p8\n",
 				__func__);
 			return ret;
 		}

 		ret = regulator_set_optimum_mode(hsusb_3p3,
 				USB_PHY_3P3_LPM_LOAD);
 		if (ret < 0) {
 			pr_err("%s: Unable to set LPM of the regulator: HSUSB_3p3\n",
 				__func__);
 			regulator_set_optimum_mode(hsusb_1p8, USB_PHY_REG_ON);
 			return ret;
 		}

 		break;

 	case USB_PHY_REG_LPM_OFF:
 		ret = regulator_set_optimum_mode(hsusb_1p8,
 				USB_PHY_1P8_HPM_LOAD);
 		if (ret < 0) {
 			pr_err("%s: Unable to set HPM of the regulator: HSUSB_1p8\n",
 				__func__);
 			return ret;
 		}

 		ret = regulator_set_optimum_mode(hsusb_3p3,
 				USB_PHY_3P3_HPM_LOAD);
 		if (ret < 0) {
 			pr_err("%s: Unable to set HPM of the regulator: HSUSB_3p3\n",
 				__func__);
 			regulator_set_optimum_mode(hsusb_1p8, USB_PHY_REG_ON);
 			return ret;
 		}

 		break;

 	default:
 		pr_err("%s: Unsupported mode (%d).", __func__, mode);
 		return -ENOTSUPP;
 	}

 	pr_debug("%s: USB reg mode (%d) (OFF/HPM/LPM)\n", __func__, mode);
 	return ret < 0 ? ret : 0;
 }

 static void msm_hsusb_mhl_switch_enable(struct msm_otg *motg, bool on)
 {
 	struct msm_otg_platform_data *pdata = motg->pdata;

 	if (!pdata->mhl_enable)
 		return;

 	if (!mhl_usb_hs_switch) {
 		pr_err("%s: mhl_usb_hs_switch is NULL.\n", __func__);
 		return;
 	}

 	if (on) {
 		if (regulator_enable(mhl_usb_hs_switch))
 			pr_err("unable to enable mhl_usb_hs_switch\n");
 	} else {
 		regulator_disable(mhl_usb_hs_switch);
 	}
 }

 static int ulpi_read(struct usb_phy *phy, u32 reg)
 {
 	struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
 	int cnt = 0;

 	/* initiate read operation */
 	writel(ULPI_RUN | ULPI_READ | ULPI_ADDR(reg),
 	       USB_ULPI_VIEWPORT);

 	/* wait for completion */
 	while (cnt < ULPI_IO_TIMEOUT_USEC) {
 		if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN))
 			break;
 		udelay(1);
 		cnt++;
 	}

 	if (cnt >= ULPI_IO_TIMEOUT_USEC) {
 		dev_err(phy->dev, "ulpi_read: timeout %08x\n",
 			readl(USB_ULPI_VIEWPORT));
 		dev_err(phy->dev, "PORTSC: %08x USBCMD: %08x\n",
 			readl_relaxed(USB_PORTSC), readl_relaxed(USB_USBCMD));
 		return -ETIMEDOUT;
 	}
 	return ULPI_DATA_READ(readl(USB_ULPI_VIEWPORT));
 }

 static int ulpi_write(struct usb_phy *phy, u32 val, u32 reg)
 {
 	struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
 	int cnt = 0;

 	/* initiate write operation */
 	writel(ULPI_RUN | ULPI_WRITE |
 	       ULPI_ADDR(reg) | ULPI_DATA(val),
 	       USB_ULPI_VIEWPORT);

 	/* wait for completion */
 	while (cnt < ULPI_IO_TIMEOUT_USEC) {
 		if (!(readl(USB_ULPI_VIEWPORT) & ULPI_RUN))
 			break;
 		udelay(1);
 		cnt++;
 	}

 	if (cnt >= ULPI_IO_TIMEOUT_USEC) {
 		dev_err(phy->dev, "ulpi_write: timeout\n");
 		dev_err(phy->dev, "PORTSC: %08x USBCMD: %08x\n",
 			readl_relaxed(USB_PORTSC), readl_relaxed(USB_USBCMD));
 		return -ETIMEDOUT;
 	}
 	return 0;
 }

 static struct usb_phy_io_ops msm_otg_io_ops = {
 	.read = ulpi_read,
 	.write = ulpi_write,
 };

 static void ulpi_init(struct msm_otg *motg)
 {
 	struct msm_otg_platform_data *pdata = motg->pdata;
 	int aseq[10];
 	int *seq = NULL;

 	if (override_phy_init) {
 		pr_debug("%s(): HUSB PHY Init:%s\n", __func__,
 				override_phy_init);
 		get_options(override_phy_init, ARRAY_SIZE(aseq), aseq);
 		seq = &aseq[1];
 	} else {
 		seq = pdata->phy_init_seq;
 	}

 	if (!seq)
 		return;

 	while (seq[0] >= 0) {
 		if (override_phy_init)
 			pr_debug("ulpi: write 0x%02x to 0x%02x\n",
 					seq[0], seq[1]);

 		dev_vdbg(motg->phy.dev, "ulpi: write 0x%02x to 0x%02x\n",
 				seq[0], seq[1]);
 		ulpi_write(&motg->phy, seq[0], seq[1]);
 		seq += 2;
 	}
 }

 static int msm_otg_link_clk_reset(struct msm_otg *motg, bool assert)
 {
 	int ret;

 	if (assert) {
 		if (!IS_ERR(motg->clk)) {
 			ret = clk_reset(motg->clk, CLK_RESET_ASSERT);
 		} else {
 			/* Using asynchronous block reset to the hardware */
 			dev_dbg(motg->phy.dev, "block_reset ASSERT\n");
 			clk_disable_unprepare(motg->pclk);
 			clk_disable_unprepare(motg->core_clk);
 			ret = clk_reset(motg->core_clk, CLK_RESET_ASSERT);
 		}
 		if (ret)
 			dev_err(motg->phy.dev, "usb hs_clk assert failed\n");
 	} else {
 		if (!IS_ERR(motg->clk)) {
 			ret = clk_reset(motg->clk, CLK_RESET_DEASSERT);
 		} else {
 			dev_dbg(motg->phy.dev, "block_reset DEASSERT\n");
 			ret = clk_reset(motg->core_clk, CLK_RESET_DEASSERT);
 			ndelay(200);
 			clk_prepare_enable(motg->core_clk);
 			clk_prepare_enable(motg->pclk);
 		}
 		if (ret)
 			dev_err(motg->phy.dev, "usb hs_clk deassert failed\n");
 	}
 	return ret;
 }

 static int msm_otg_phy_reset(struct msm_otg *motg)
 {
 	u32 val;
 	int ret;
 	struct msm_otg_platform_data *pdata = motg->pdata;

 	/*
 	 * AHB2AHB Bypass mode shouldn't be enable before doing
 	 * async clock reset. If it is enable, disable the same.
 	 */
 	val = readl_relaxed(USB_AHBMODE);
 	if (val & AHB2AHB_BYPASS) {
 		pr_err("%s(): AHB2AHB_BYPASS SET: AHBMODE:%x\n",
 				__func__, val);
 		val &= ~AHB2AHB_BYPASS_BIT_MASK;
 		writel_relaxed(val | AHB2AHB_BYPASS_CLEAR, USB_AHBMODE);
 		pr_err("%s(): AHBMODE: %x\n", __func__,
 				readl_relaxed(USB_AHBMODE));
 	}

 	ret = msm_otg_link_clk_reset(motg, 1);
 	if (ret)
 		return ret;

 	/* wait for 1ms delay as suggested in HPG. */
 	usleep_range(1000, 1200);

 	ret = msm_otg_link_clk_reset(motg, 0);
 	if (ret)
 		return ret;

 	if (pdata && pdata->enable_sec_phy)
 		writel_relaxed(readl_relaxed(USB_PHY_CTRL2) | (1<<16),
 							USB_PHY_CTRL2);
 	val = readl(USB_PORTSC) & ~PORTSC_PTS_MASK;
 	writel(val | PORTSC_PTS_ULPI, USB_PORTSC);

 	dev_info(motg->phy.dev, "phy_reset: success\n");
 	return 0;
 }

 #define LINK_RESET_TIMEOUT_USEC		(250 * 1000)
 static int msm_otg_link_reset(struct msm_otg *motg)
 {
 	int cnt = 0;
 	struct msm_otg_platform_data *pdata = motg->pdata;

 	writel_relaxed(USBCMD_RESET, USB_USBCMD);
 	while (cnt < LINK_RESET_TIMEOUT_USEC) {
 		if (!(readl_relaxed(USB_USBCMD) & USBCMD_RESET))
 			break;
 		udelay(1);
 		cnt++;
 	}
 	if (cnt >= LINK_RESET_TIMEOUT_USEC)
 		return -ETIMEDOUT;

 	/* select ULPI phy */
 	writel_relaxed(0x80000000, USB_PORTSC);
 	writel_relaxed(0x0, USB_AHBBURST);
 	writel_relaxed(0x08, USB_AHBMODE);

 	if (pdata && pdata->enable_sec_phy)
 		writel_relaxed(readl_relaxed(USB_PHY_CTRL2) | (1<<16),
 								USB_PHY_CTRL2);
 	return 0;
 }

 static void usb_phy_reset(struct msm_otg *motg)
 {
 	u32 val;

 	if (motg->pdata->phy_type != SNPS_28NM_INTEGRATED_PHY)
 		return;

 	/* Assert USB PHY_PON */
 	val =  readl_relaxed(USB_PHY_CTRL);
 	val &= ~PHY_POR_BIT_MASK;
 	val |= PHY_POR_ASSERT;
 	writel_relaxed(val, USB_PHY_CTRL);

 	/* wait for minimum 10 microseconds as suggested in HPG. */
 	usleep_range(10, 15);

 	/* Deassert USB PHY_PON */
 	val =  readl_relaxed(USB_PHY_CTRL);
 	val &= ~PHY_POR_BIT_MASK;
 	val |= PHY_POR_DEASSERT;
 	writel_relaxed(val, USB_PHY_CTRL);

 	/* Ensure that RESET operation is completed. */
 	mb();
 }

 static int msm_otg_reset(struct usb_phy *phy)
 {
 	struct msm_otg *motg = container_of(phy, struct msm_otg, phy);
 	struct msm_otg_platform_data *pdata = motg->pdata;
 	int ret;
 	u32 val = 0;
 	u32 ulpi_val = 0;

 	/*
 	 * USB PHY and Link reset also reset the USB BAM.
 	 * Thus perform reset operation only once to avoid
 	 * USB BAM reset on other cases e.g. USB cable disconnections.
 	 */
 	if (pdata->disable_reset_on_disconnect) {
 		if (motg->reset_counter)
 			return 0;
 		else
 			motg->reset_counter++;
 	}

 	if (!IS_ERR(motg->clk))
 		clk_prepare_enable(motg->clk);
 	ret = msm_otg_phy_reset(motg);
 	if (ret) {
 		dev_err(phy->dev, "phy_reset failed\n");
 		return ret;
 	}

 	aca_id_turned_on = false;
 	ret = msm_otg_link_reset(motg);
 	if (ret) {
 		dev_err(phy->dev, "link reset failed\n");
 		return ret;
 	}

 	msleep(100);

 	/* Reset USB PHY after performing USB Link RESET */
 	usb_phy_reset(motg);

 	/* Program USB PHY Override registers. */
 	ulpi_init(motg);

 	/*
 	 * It is recommended in HPG to reset USB PHY after programming
 	 * USB PHY Override registers.
 	 */
 	usb_phy_reset(motg);

 	if (!IS_ERR(motg->clk))
 		clk_disable_unprepare(motg->clk);

 	if (pdata->otg_control == OTG_PHY_CONTROL) {
 		val = readl_relaxed(USB_OTGSC);
 		if (pdata->mode == USB_OTG) {
 			ulpi_val = ULPI_INT_IDGRD | ULPI_INT_SESS_VALID;
 			val |= OTGSC_IDIE | OTGSC_BSVIE;
 		} else if (pdata->mode == USB_PERIPHERAL) {
 			ulpi_val = ULPI_INT_SESS_VALID;
 			val |= OTGSC_BSVIE;
 		}
 		writel_relaxed(val, USB_OTGSC);
 		ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_RISE);
 		ulpi_write(phy, ulpi_val, ULPI_USB_INT_EN_FALL);
 	} else if (pdata->otg_control == OTG_PMIC_CONTROL) {
 		ulpi_write(phy, OTG_COMP_DISABLE,
 			ULPI_SET(ULPI_PWR_CLK_MNG_REG));
 		/* Enable PMIC pull-up */
 		pm8xxx_usb_id_pullup(1);
 	}

 	if (motg->caps & ALLOW_VDD_MIN_WITH_RETENTION_DISABLED)
 		writel_relaxed(readl_relaxed(USB_OTGSC) & ~(OTGSC_IDPU),
 								USB_OTGSC);

 	return 0;
 }

 static const char *timer_string(int bit)
 {
 	switch (bit) {
 	case A_WAIT_VRISE:		return "a_wait_vrise";
 	case A_WAIT_VFALL:		return "a_wait_vfall";
 	case B_SRP_FAIL:		return "b_srp_fail";
 	case A_WAIT_BCON:		return "a_wait_bcon";
 	case A_AIDL_BDIS:		return "a_aidl_bdis";
 	case A_BIDL_ADIS:		return "a_bidl_adis";
 	case B_ASE0_BRST:		return "b_ase0_brst";
 	case A_TST_MAINT:		return "a_tst_maint";
 	case B_TST_SRP:			return "b_tst_srp";
 	case B_TST_CONFIG:		return "b_tst_config";
 	default:			return "UNDEFINED";
 	}
 }

 static enum hrtimer_restart msm_otg_timer_func(struct hrtimer *hrtimer)
 {
 	struct msm_otg *motg = container_of(hrtimer, struct msm_otg, timer);

 	switch (motg->active_tmout) {
 	case A_WAIT_VRISE:
 		/* TODO: use vbus_vld interrupt */
 		set_bit(A_VBUS_VLD, &motg->inputs);
 		break;
 	case A_TST_MAINT:
 		/* OTG PET: End session after TA_TST_MAINT */
 		set_bit(A_BUS_DROP, &motg->inputs);
 		break;
 	case B_TST_SRP:
 		/*
 		 * OTG PET: Initiate SRP after TB_TST_SRP of
 		 * previous session end.
 		 */
 		set_bit(B_BUS_REQ, &motg->inputs);
 		break;
 	case B_TST_CONFIG:
 		clear_bit(A_CONN, &motg->inputs);
 		break;
 	default:
 		set_bit(motg->active_tmout, &motg->tmouts);
 	}

 	pr_debug("expired %s timer\n", timer_string(motg->active_tmout));
 	queue_work(system_nrt_wq, &motg->sm_work);
 	return HRTIMER_NORESTART;
 }

 static void msm_otg_del_timer(struct msm_otg *motg)
 {
 	int bit = motg->active_tmout;

 	pr_debug("deleting %s timer. remaining %lld msec\n", timer_string(bit),
 			div_s64(ktime_to_us(hrtimer_get_remaining(
 					&motg->timer)), 1000));
 	hrtimer_cancel(&motg->timer);
 	clear_bit(bit, &motg->tmouts);
 }

 static void msm_otg_start_timer(struct msm_otg *motg, int time, int bit)
 {
 	clear_bit(bit, &motg->tmouts);
 	motg->active_tmout = bit;
 	pr_debug("starting %s timer\n", timer_string(bit));
 	hrtimer_start(&motg->timer,
 			ktime_set(time / 1000, (time % 1000) * 1000000),
 			HRTIMER_MODE_REL);
 }

 static void msm_otg_init_timer(struct msm_otg *motg)
 {
 	hrtimer_init(&motg->timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
 	motg->timer.function = msm_otg_timer_func;
 }

 static int msm_otg_start_hnp(struct usb_otg *otg)
 {
 	struct msm_otg *motg = container_of(otg->phy, struct msm_otg, phy);

 	if (otg->phy->state != OTG_STATE_A_HOST) {
 		pr_err("HNP can not be initiated in %s state\n",
 				otg_state_string(otg->phy->state));
 		return -EINVAL;
 	}

 	pr_debug("A-Host: HNP initiated\n");
 	clear_bit(A_BUS_REQ, &motg->inputs);
 	queue_work(system_nrt_wq, &motg->sm_work);
 	return 0;
 }

 static int msm_otg_start_srp(struct usb_otg *otg)
 {
 	struct msm_otg *motg = container_of(otg->phy, struct msm_otg, phy);
 	u32 val;
 	int ret = 0;

 	if (otg->phy->state != OTG_STATE_B_IDLE) {
 		pr_err("SRP can not be initiated in %s state\n",
 				otg_state_string(otg->phy->state));
 		ret = -EINVAL;
 		goto out;
 	}

 	if ((jiffies - motg->b_last_se0_sess) < msecs_to_jiffies(TB_SRP_INIT)) {
 		pr_debug("initial conditions of SRP are not met. Try again"
 				"after some time\n");
 		ret = -EAGAIN;
 		goto out;
 	}

 	pr_debug("B-Device SRP started\n");

 	/*
 	 * PHY won't pull D+ high unless it detects Vbus valid.
 	 * Since by definition, SRP is only done when Vbus is not valid,
 	 * software work-around needs to be used to spoof the PHY into
 	 * thinking it is valid. This can be done using the VBUSVLDEXTSEL and
 	 * VBUSVLDEXT register bits.
 	 */
 	ulpi_write(otg->phy, 0x03, 0x97);
 	/*
 	 * Harware auto assist data pulsing: Data pulse is given
 	 * for 7msec; wait for vbus
 	 */
 	val = readl_relaxed(USB_OTGSC);
 	writel_relaxed((val & ~OTGSC_INTSTS_MASK) | OTGSC_HADP, USB_OTGSC);

 	/* VBUS plusing is obsoleted in OTG 2.0 supplement */
 out:
 	return ret;
 }

 static void msm_otg_host_hnp_enable(struct usb_otg *otg, bool enable)
 {
 	struct usb_hcd *hcd = bus_to_hcd(otg->host);
 	struct usb_device *rhub = otg->host->root_hub;

 	if (enable) {
 		pm_runtime_disable(&rhub->dev);
 		rhub->state = USB_STATE_NOTATTACHED;
 		hcd->driver->bus_suspend(hcd);
 		clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
 	} else {
 		usb_remove_hcd(hcd);
 		msm_otg_reset(otg->phy);
 		usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
 	}
 }

 static int msm_otg_set_suspend(struct usb_phy *phy, int suspend)
 {
 	struct msm_otg *motg = container_of(phy, struct msm_otg, phy);

 	if (aca_enabled())
 		return 0;

 	/*
 	 * UDC and HCD call usb_phy_set_suspend() to enter/exit LPM
 	 * during bus suspend/resume.  Update the relevant state
 	 * machine inputs and trigger LPM entry/exit.  Checking
 	 * in_lpm flag would avoid unnecessary work scheduling.
 	 */
 	if (suspend) {
 		switch (phy->state) {
 		case OTG_STATE_A_WAIT_BCON:
 			if (TA_WAIT_BCON > 0)
 				break;
 			/* fall through */
 		case OTG_STATE_A_HOST:
 			pr_debug("host bus suspend\n");
 			clear_bit(A_BUS_REQ, &motg->inputs);
 			if (!atomic_read(&motg->in_lpm))
 				queue_work(system_nrt_wq, &motg->sm_work);
 			break;
 		case OTG_STATE_B_PERIPHERAL:
 			pr_debug("peripheral bus suspend\n");
 			if (!(motg->caps & ALLOW_LPM_ON_DEV_SUSPEND))
 				break;
 			set_bit(A_BUS_SUSPEND, &motg->inputs);
 			if (!atomic_read(&motg->in_lpm))
 				queue_delayed_work(system_nrt_wq,
 					&motg->suspend_work,
 					USB_SUSPEND_DELAY_TIME);
 			break;

 		default:
 			break;
 		}
 	} else {
 		switch (phy->state) {
 		case OTG_STATE_A_WAIT_BCON:
 			/* Remote wakeup or resume */
 			set_bit(A_BUS_REQ, &motg->inputs);
 			/* ensure hardware is not in low power mode */
 			if (atomic_read(&motg->in_lpm))
 				pm_runtime_resume(phy->dev);
 			break;
 		case OTG_STATE_A_SUSPEND:
 			/* Remote wakeup or resume */
 			set_bit(A_BUS_REQ, &motg->inputs);
 			phy->state = OTG_STATE_A_HOST;

 			/* ensure hardware is not in low power mode */
 			if (atomic_read(&motg->in_lpm))
 				pm_runtime_resume(phy->dev);
 			break;
 		case OTG_STATE_B_PERIPHERAL:
 			pr_debug("peripheral bus resume\n");
 			if (!(motg->caps & ALLOW_LPM_ON_DEV_SUSPEND))
 				break;
 			clear_bit(A_BUS_SUSPEND, &motg->inputs);
 			if (atomic_read(&motg->in_lpm))
 				queue_work(system_nrt_wq, &motg->sm_work);
 			break;
 		default:
 			break;
 		}
 	}
 	return 0;
 }

 static void msm_otg_bus_vote(struct msm_otg *motg, enum usb_bus_vote vote)
 {
 	int ret;
 	struct msm_otg_platform_data *pdata = motg->pdata;

 	/* Check if target allows min_vote to be same as no_vote */
 	if (pdata->bus_scale_table &&
 	    vote >= pdata->bus_scale_table->num_usecases)
 		vote = USB_NO_PERF_VOTE;

 	if (motg->bus_perf_client) {
 		ret = msm_bus_scale_client_update_request(
 			motg->bus_perf_client, vote);
 		if (ret)
 			dev_err(motg->phy.dev, "%s: Failed to vote (%d)\n"
 				   "for bus bw %d\n", __func__, vote, ret);
 	}
 }

 #define PHY_SUSPEND_TIMEOUT_USEC	(500 * 1000)
 #define PHY_RESUME_TIMEOUT_USEC	(100 * 1000)

 #ifdef CONFIG_PM_SLEEP
 static int msm_otg_suspend(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	struct usb_bus *bus = phy->otg->host;
 	struct msm_otg_platform_data *pdata = motg->pdata;
 	int cnt = 0;
 	bool host_bus_suspend, device_bus_suspend, dcp, prop_charger;
 	bool floated_charger;
 	u32 phy_ctrl_val = 0, cmd_val;
 	unsigned ret;
 	u32 portsc, config2;
 	u32 func_ctrl;

 	if (atomic_read(&motg->in_lpm))
 		return 0;

 	if (motg->pdata->delay_lpm_hndshk_on_disconnect && !msm_bam_lpm_ok())
 		return -EBUSY;

 	motg->ui_enabled = 0;
 	disable_irq(motg->irq);
 	host_bus_suspend = !test_bit(MHL, &motg->inputs) && phy->otg->host &&
 		!test_bit(ID, &motg->inputs);
 	device_bus_suspend = phy->otg->gadget && test_bit(ID, &motg->inputs) &&
 		test_bit(A_BUS_SUSPEND, &motg->inputs) &&
 		motg->caps & ALLOW_LPM_ON_DEV_SUSPEND;
 	dcp = motg->chg_type == USB_DCP_CHARGER;
 	prop_charger = motg->chg_type == USB_PROPRIETARY_CHARGER;
 	floated_charger = motg->chg_type == USB_FLOATED_CHARGER;

 	/* Enable line state difference wakeup fix for only device and host
 	 * bus suspend scenarios.  Otherwise PHY can not be suspended when
 	 * a charger that pulls DP/DM high is connected.
 	 */
 	config2 = readl_relaxed(USB_GENCONFIG2);
 	if (device_bus_suspend)
 		config2 |= GENCFG2_LINESTATE_DIFF_WAKEUP_EN;
 	else
 		config2 &= ~GENCFG2_LINESTATE_DIFF_WAKEUP_EN;
 	writel_relaxed(config2, USB_GENCONFIG2);

 	/*
 	 * Abort suspend when,
 	 * 1. charging detection in progress due to cable plug-in
 	 * 2. host mode activation in progress due to Micro-A cable insertion
 	 */

 	if ((test_bit(B_SESS_VLD, &motg->inputs) && !device_bus_suspend &&
 		!dcp && !prop_charger && !floated_charger) ||
 		test_bit(A_BUS_REQ, &motg->inputs)) {
 		motg->ui_enabled = 1;
 		enable_irq(motg->irq);
 		return -EBUSY;
 	}

 	/*
 	 * Chipidea 45-nm PHY suspend sequence:
 	 *
 	 * Interrupt Latch Register auto-clear feature is not present
 	 * in all PHY versions. Latch register is clear on read type.
 	 * Clear latch register to avoid spurious wakeup from
 	 * low power mode (LPM).
 	 *
 	 * PHY comparators are disabled when PHY enters into low power
 	 * mode (LPM). Keep PHY comparators ON in LPM only when we expect
 	 * VBUS/Id notifications from USB PHY. Otherwise turn off USB
 	 * PHY comparators. This save significant amount of power.
 	 *
 	 * PLL is not turned off when PHY enters into low power mode (LPM).
 	 * Disable PLL for maximum power savings.
 	 */

 	if (motg->pdata->phy_type == CI_45NM_INTEGRATED_PHY) {
 		ulpi_read(phy, 0x14);
 		if (pdata->otg_control == OTG_PHY_CONTROL)
 			ulpi_write(phy, 0x01, 0x30);
 		ulpi_write(phy, 0x08, 0x09);
 	}

 	if (motg->caps & ALLOW_VDD_MIN_WITH_RETENTION_DISABLED) {
 		/* put the controller in non-driving mode */
 		func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
 		func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
 		func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
 		ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
 		ulpi_write(phy, ULPI_IFC_CTRL_AUTORESUME,
 				ULPI_CLR(ULPI_IFC_CTRL));
 	}

 	/* Set the PHCD bit, only if it is not set by the controller.
 	 * PHY may take some time or even fail to enter into low power
 	 * mode (LPM). Hence poll for 500 msec and reset the PHY and link
 	 * in failure case.
 	 */
 	portsc = readl_relaxed(USB_PORTSC);
 	if (!(portsc & PORTSC_PHCD)) {
 		writel_relaxed(portsc | PORTSC_PHCD,
 				USB_PORTSC);
 		while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
 			if (readl_relaxed(USB_PORTSC) & PORTSC_PHCD)
 				break;
 			udelay(1);
 			cnt++;
 		}
 	}

 	if (cnt >= PHY_SUSPEND_TIMEOUT_USEC) {
 		dev_err(phy->dev, "Unable to suspend PHY\n");
 		msm_otg_reset(phy);
 		motg->ui_enabled = 1;
 		enable_irq(motg->irq);
 		return -ETIMEDOUT;
 	}

 	/*
 	 * PHY has capability to generate interrupt asynchronously in low
 	 * power mode (LPM). This interrupt is level triggered. So USB IRQ
 	 * line must be disabled till async interrupt enable bit is cleared
 	 * in USBCMD register. Assert STP (ULPI interface STOP signal) to
 	 * block data communication from PHY.
 	 *
 	 * PHY retention mode is disallowed while entering to LPM with wall
 	 * charger connected.  But PHY is put into suspend mode. Hence
 	 * enable asynchronous interrupt to detect charger disconnection when
 	 * PMIC notifications are unavailable.
 	 */
 	cmd_val = readl_relaxed(USB_USBCMD);
 	if (host_bus_suspend || device_bus_suspend ||
 		(motg->pdata->otg_control == OTG_PHY_CONTROL))
 		cmd_val |= ASYNC_INTR_CTRL | ULPI_STP_CTRL;
 	else
 		cmd_val |= ULPI_STP_CTRL;
 	writel_relaxed(cmd_val, USB_USBCMD);

 	/*
 	 * BC1.2 spec mandates PD to enable VDP_SRC when charging from DCP.
 	 * PHY retention and collapse can not happen with VDP_SRC enabled.
 	 */
 	if (motg->caps & ALLOW_PHY_RETENTION && !device_bus_suspend && !dcp &&
 		 (!host_bus_suspend || ((motg->caps & ALLOW_HOST_PHY_RETENTION)
 		&& (pdata->dpdm_pulldown_added || !(portsc & PORTSC_CCS))))) {
 		phy_ctrl_val = readl_relaxed(USB_PHY_CTRL);
 		if (motg->pdata->otg_control == OTG_PHY_CONTROL) {
 			/* Enable PHY HV interrupts to wake MPM/Link */
 			if ((motg->pdata->mode == USB_OTG) ||
 					(motg->pdata->mode == USB_HOST))
 				phy_ctrl_val |= (PHY_IDHV_INTEN |
 							PHY_OTGSESSVLDHV_INTEN);
 			else
 				phy_ctrl_val |= PHY_OTGSESSVLDHV_INTEN;
 		}
 		if (host_bus_suspend)
 			phy_ctrl_val |= PHY_CLAMP_DPDMSE_EN;

 		if (!(motg->caps & ALLOW_VDD_MIN_WITH_RETENTION_DISABLED)) {
 			writel_relaxed(phy_ctrl_val & ~PHY_RETEN, USB_PHY_CTRL);
 			motg->lpm_flags |= PHY_RETENTIONED;
 		} else {
 			writel_relaxed(phy_ctrl_val, USB_PHY_CTRL);
 		}
 	}

 	/* Ensure that above operation is completed before turning off clocks */
 	mb();
 	/* Consider clocks on workaround flag only in case of bus suspend */
 	if (!(phy->state == OTG_STATE_B_PERIPHERAL &&
 		test_bit(A_BUS_SUSPEND, &motg->inputs)) ||
 	    !motg->pdata->core_clk_always_on_workaround) {
 		clk_disable_unprepare(motg->pclk);
 		clk_disable_unprepare(motg->core_clk);
 		motg->lpm_flags |= CLOCKS_DOWN;
 	}

 	/* usb phy no more require TCXO clock, hence vote for TCXO disable */
 	if (!host_bus_suspend || ((motg->caps & ALLOW_HOST_PHY_RETENTION) &&
 		(pdata->dpdm_pulldown_added || !(portsc & PORTSC_CCS)))) {
 		if (!IS_ERR(motg->xo_clk)) {
 			clk_disable_unprepare(motg->xo_clk);
 			motg->lpm_flags |= XO_SHUTDOWN;
 		} else {
 			ret = msm_xo_mode_vote(motg->xo_handle,
 							MSM_XO_MODE_OFF);
 			if (ret)
 				dev_err(phy->dev, "%s fail to devote XO %d\n",
 								 __func__, ret);
 			else
 				motg->lpm_flags |= XO_SHUTDOWN;
 		}
 	}

 	if (motg->caps & ALLOW_PHY_POWER_COLLAPSE &&
 			!host_bus_suspend && !dcp) {
 		msm_hsusb_ldo_enable(motg, USB_PHY_REG_OFF);
 		motg->lpm_flags |= PHY_PWR_COLLAPSED;
 	} else if (motg->caps & ALLOW_PHY_REGULATORS_LPM &&
 			!host_bus_suspend && !device_bus_suspend && !dcp) {
 		msm_hsusb_ldo_enable(motg, USB_PHY_REG_LPM_ON);
 		motg->lpm_flags |= PHY_REGULATORS_LPM;
 	}

 	if (motg->lpm_flags & PHY_RETENTIONED ||
 		(motg->caps & ALLOW_VDD_MIN_WITH_RETENTION_DISABLED)) {
 		msm_hsusb_config_vddcx(0);
 		msm_hsusb_mhl_switch_enable(motg, 0);
 	}

 	if (device_may_wakeup(phy->dev)) {
 		if (motg->async_irq)
 			enable_irq_wake(motg->async_irq);
 		else
 			enable_irq_wake(motg->irq);

 		if (motg->pdata->pmic_id_irq)
 			enable_irq_wake(motg->pdata->pmic_id_irq);
 		if (pdata->otg_control == OTG_PHY_CONTROL &&
 			pdata->mpm_otgsessvld_int)
 			msm_mpm_set_pin_wake(pdata->mpm_otgsessvld_int, 1);
 		if (host_bus_suspend && pdata->mpm_dpshv_int)
 			msm_mpm_set_pin_wake(pdata->mpm_dpshv_int, 1);
 		if (host_bus_suspend && pdata->mpm_dmshv_int)
 			msm_mpm_set_pin_wake(pdata->mpm_dmshv_int, 1);
 	}
 	if (bus)
 		clear_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);

 	msm_otg_bus_vote(motg, USB_NO_PERF_VOTE);

 	motg->host_bus_suspend = host_bus_suspend;
 	atomic_set(&motg->in_lpm, 1);
 	/* Enable ASYNC IRQ (if present) during LPM */
 	if (motg->async_irq)
 		enable_irq(motg->async_irq);

 	/* XO shutdown during idle , non wakeable irqs must be disabled */
 	if (device_bus_suspend || host_bus_suspend || !motg->async_irq) {
 		motg->ui_enabled = 1;
 		enable_irq(motg->irq);
 	}
 	wake_unlock(&motg->wlock);

 	dev_info(phy->dev, "USB in low power mode\n");

 	return 0;
 }

 static int msm_otg_resume(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	struct usb_bus *bus = phy->otg->host;
 	struct msm_otg_platform_data *pdata = motg->pdata;
 	int cnt = 0;
 	unsigned temp;
 	u32 phy_ctrl_val = 0;
 	unsigned ret;
 	u32 func_ctrl;

 	if (!atomic_read(&motg->in_lpm))
 		return 0;

 	if (motg->pdata->delay_lpm_hndshk_on_disconnect)
 		msm_bam_notify_lpm_resume();

 	if (motg->ui_enabled) {
 		motg->ui_enabled = 0;
 		disable_irq(motg->irq);
 	}
 	wake_lock(&motg->wlock);

 	/* Some platforms require BUS vote to enable/disable clocks */
 	msm_otg_bus_vote(motg, USB_MIN_PERF_VOTE);

 	/* Vote for TCXO when waking up the phy */
 	if (motg->lpm_flags & XO_SHUTDOWN) {
 		if (!IS_ERR(motg->xo_clk)) {
 			clk_prepare_enable(motg->xo_clk);
 		} else {
 			ret = msm_xo_mode_vote(motg->xo_handle, MSM_XO_MODE_ON);
 			if (ret)
 				dev_err(phy->dev, "%s fail to vote for XO %d\n",
 								__func__, ret);
 		}
 		motg->lpm_flags &= ~XO_SHUTDOWN;
 	}

 	if (motg->lpm_flags & CLOCKS_DOWN) {
 		clk_prepare_enable(motg->core_clk);
 		clk_prepare_enable(motg->pclk);
 		motg->lpm_flags &= ~CLOCKS_DOWN;
 	}

 	if (motg->lpm_flags & PHY_PWR_COLLAPSED) {
 		msm_hsusb_ldo_enable(motg, USB_PHY_REG_ON);
 		motg->lpm_flags &= ~PHY_PWR_COLLAPSED;
 	} else if (motg->lpm_flags & PHY_REGULATORS_LPM) {
 		msm_hsusb_ldo_enable(motg, USB_PHY_REG_LPM_OFF);
 		motg->lpm_flags &= ~PHY_REGULATORS_LPM;
 	}

 	if (motg->lpm_flags & PHY_RETENTIONED ||
 		(motg->caps & ALLOW_VDD_MIN_WITH_RETENTION_DISABLED)) {
 		msm_hsusb_mhl_switch_enable(motg, 1);
 		msm_hsusb_config_vddcx(1);
 		phy_ctrl_val = readl_relaxed(USB_PHY_CTRL);
 		phy_ctrl_val |= PHY_RETEN;
 		if (motg->pdata->otg_control == OTG_PHY_CONTROL)
 			/* Disable PHY HV interrupts */
 			phy_ctrl_val &=
 				~(PHY_IDHV_INTEN | PHY_OTGSESSVLDHV_INTEN);
 		phy_ctrl_val &= ~(PHY_CLAMP_DPDMSE_EN);
 		writel_relaxed(phy_ctrl_val, USB_PHY_CTRL);
 		motg->lpm_flags &= ~PHY_RETENTIONED;
 	}

 	temp = readl(USB_USBCMD);
 	temp &= ~ASYNC_INTR_CTRL;
 	temp &= ~ULPI_STP_CTRL;
 	writel(temp, USB_USBCMD);

 	/*
 	 * PHY comes out of low power mode (LPM) in case of wakeup
 	 * from asynchronous interrupt.
 	 */
 	if (!(readl(USB_PORTSC) & PORTSC_PHCD))
 		goto skip_phy_resume;

 	writel(readl(USB_PORTSC) & ~PORTSC_PHCD, USB_PORTSC);
 	while (cnt < PHY_RESUME_TIMEOUT_USEC) {
 		if (!(readl(USB_PORTSC) & PORTSC_PHCD))
 			break;
 		udelay(1);
 		cnt++;
 	}

 	if (cnt >= PHY_RESUME_TIMEOUT_USEC) {
 		/*
 		 * This is a fatal error. Reset the link and
 		 * PHY. USB state can not be restored. Re-insertion
 		 * of USB cable is the only way to get USB working.
 		 */
 		dev_err(phy->dev, "Unable to resume USB."
 				"Re-plugin the cable\n");
 		msm_otg_reset(phy);
 	}

 skip_phy_resume:
 	if (motg->caps & ALLOW_VDD_MIN_WITH_RETENTION_DISABLED) {
 		/* put the controller in normal mode */
 		func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
 		func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
 		func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
 		ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
 	}

 	if (device_may_wakeup(phy->dev)) {
 		if (motg->async_irq)
 			disable_irq_wake(motg->async_irq);
 		else
 			disable_irq_wake(motg->irq);

 		if (motg->pdata->pmic_id_irq)
 			disable_irq_wake(motg->pdata->pmic_id_irq);
 		if (pdata->otg_control == OTG_PHY_CONTROL &&
 			pdata->mpm_otgsessvld_int)
 			msm_mpm_set_pin_wake(pdata->mpm_otgsessvld_int, 0);
 		if (motg->host_bus_suspend && pdata->mpm_dpshv_int)
 			msm_mpm_set_pin_wake(pdata->mpm_dpshv_int, 0);
 		if (motg->host_bus_suspend && pdata->mpm_dmshv_int)
 			msm_mpm_set_pin_wake(pdata->mpm_dmshv_int, 0);
 	}
 	if (bus)
 		set_bit(HCD_FLAG_HW_ACCESSIBLE, &(bus_to_hcd(bus))->flags);

 	atomic_set(&motg->in_lpm, 0);

 	if (motg->async_int) {
 		/* Match the disable_irq call from ISR */
 		enable_irq(motg->async_int);
 		motg->async_int = 0;
 	}
 	motg->ui_enabled = 1;
 	enable_irq(motg->irq);

 	/* If ASYNC IRQ is present then keep it enabled only during LPM */
 	if (motg->async_irq)
 		disable_irq(motg->async_irq);

 	dev_info(phy->dev, "USB exited from low power mode\n");

 	return 0;
 }
 #endif

 static void msm_otg_notify_host_mode(struct msm_otg *motg, bool host_mode)
 {
 	if (!psy) {
 		pr_err("No USB power supply registered!\n");
 		return;
 	}

 	if (legacy_power_supply) {
 		/* legacy support */
 		if (host_mode) {
 			power_supply_set_scope(psy, POWER_SUPPLY_SCOPE_SYSTEM);
 		} else {
 			power_supply_set_scope(psy, POWER_SUPPLY_SCOPE_DEVICE);
 			/*
 			 * VBUS comparator is disabled by PMIC charging driver
 			 * when SYSTEM scope is selected.  For ID_GND->ID_A
 			 * transition, give 50 msec delay so that PMIC charger
 			 * driver detect the VBUS and ready for accepting
 			 * charging current value from USB.
 			 */
 			if (test_bit(ID_A, &motg->inputs))
 				msleep(50);
 		}
 	} else {
 		motg->host_mode = host_mode;
 		power_supply_changed(psy);
 	}
 }

 static int msm_otg_notify_chg_type(struct msm_otg *motg)
 {
 	static int charger_type;

 	/*
 	 * TODO
 	 * Unify OTG driver charger types and power supply charger types
 	 */
 	if (charger_type == motg->chg_type)
 		return 0;

 	if (motg->chg_type == USB_SDP_CHARGER)
 		charger_type = POWER_SUPPLY_TYPE_USB;
 	else if (motg->chg_type == USB_CDP_CHARGER)
 		charger_type = POWER_SUPPLY_TYPE_USB_CDP;
 	else if (motg->chg_type == USB_DCP_CHARGER ||
 			motg->chg_type == USB_PROPRIETARY_CHARGER ||
 			motg->chg_type == USB_FLOATED_CHARGER)
 		charger_type = POWER_SUPPLY_TYPE_USB_DCP;
 	else if ((motg->chg_type == USB_ACA_DOCK_CHARGER ||
 		motg->chg_type == USB_ACA_A_CHARGER ||
 		motg->chg_type == USB_ACA_B_CHARGER ||
 		motg->chg_type == USB_ACA_C_CHARGER))
 		charger_type = POWER_SUPPLY_TYPE_USB_ACA;
 	else
 		charger_type = POWER_SUPPLY_TYPE_UNKNOWN;

 	if (!psy) {
 		pr_err("No USB power supply registered!\n");
 		return -EINVAL;
 	}

 	pr_debug("setting usb power supply type %d\n", charger_type);
 	power_supply_set_supply_type(psy, charger_type);
 	return 0;
 }

 static int msm_otg_notify_power_supply(struct msm_otg *motg, unsigned mA)
 {
 	if (!psy) {
 		dev_dbg(motg->phy.dev, "no usb power supply registered\n");
 		goto psy_error;
 	}

 	if (motg->cur_power == 0 && mA > 2) {
 		/* Enable charging */
 		if (power_supply_set_online(psy, true))
 			goto psy_error;
 		if (power_supply_set_current_limit(psy, 1000*mA))
 			goto psy_error;
 	} else if (motg->cur_power > 0 && (mA == 0 || mA == 2)) {
 		/* Disable charging */
 		if (power_supply_set_online(psy, false))
 			goto psy_error;
 		/* Set max current limit */
 		if (power_supply_set_current_limit(psy, 0))
 			goto psy_error;
 	} else {
 		if (power_supply_set_online(psy, true))
 			goto psy_error;
 		/* Current has changed (100/2 --> 500) */
 		if (power_supply_set_current_limit(psy, 1000*mA))
 			goto psy_error;
 	}

 	power_supply_changed(psy);
 	return 0;

 psy_error:
 	dev_dbg(motg->phy.dev, "power supply error when setting property\n");
 	return -ENXIO;
 }

 static void msm_otg_notify_charger(struct msm_otg *motg, unsigned mA)
 {
 	struct usb_gadget *g = motg->phy.otg->gadget;

 	if (g && g->is_a_peripheral)
 		return;

 	if ((motg->chg_type == USB_ACA_DOCK_CHARGER ||
 		motg->chg_type == USB_ACA_A_CHARGER ||
 		motg->chg_type == USB_ACA_B_CHARGER ||
 		motg->chg_type == USB_ACA_C_CHARGER) &&
 			mA > IDEV_ACA_CHG_LIMIT)
 		mA = IDEV_ACA_CHG_LIMIT;

 	if (msm_otg_notify_chg_type(motg))
 		dev_err(motg->phy.dev,
 			"Failed notifying %d charger type to PMIC\n",
 							motg->chg_type);

 	if (motg->cur_power == mA)
 		return;

 	dev_info(motg->phy.dev, "Avail curr from USB = %u\n", mA);

 	/*
 	 *  Use Power Supply API if supported, otherwise fallback
 	 *  to legacy pm8921 API.
 	 */
 	if (msm_otg_notify_power_supply(motg, mA))
 		pm8921_charger_vbus_draw(mA);

 	motg->cur_power = mA;
 }

 static int msm_otg_set_power(struct usb_phy *phy, unsigned mA)
 {
 	struct msm_otg *motg = container_of(phy, struct msm_otg, phy);

 	/*
 	 * Gadget driver uses set_power method to notify about the
 	 * available current based on suspend/configured states.
 	 *
 	 * IDEV_CHG can be drawn irrespective of suspend/un-configured
 	 * states when CDP/ACA is connected.
 	 */
 	if (motg->chg_type == USB_SDP_CHARGER)
 		msm_otg_notify_charger(motg, mA);

 	return 0;
 }

 static void msm_otg_start_host(struct usb_otg *otg, int on)
 {
 	struct msm_otg *motg = container_of(otg->phy, struct msm_otg, phy);
 	struct msm_otg_platform_data *pdata = motg->pdata;
 	struct usb_hcd *hcd;

 	if (!otg->host)
 		return;

 	hcd = bus_to_hcd(otg->host);

 	if (on) {
 		dev_dbg(otg->phy->dev, "host on\n");

 		if (pdata->otg_control == OTG_PHY_CONTROL)
 			ulpi_write(otg->phy, OTG_COMP_DISABLE,
 				ULPI_SET(ULPI_PWR_CLK_MNG_REG));

 		/*
 		 * Some boards have a switch cotrolled by gpio
 		 * to enable/disable internal HUB. Enable internal
 		 * HUB before kicking the host.
 		 */
 		if (pdata->setup_gpio)
 			pdata->setup_gpio(OTG_STATE_A_HOST);
 		usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
 	} else {
 		dev_dbg(otg->phy->dev, "host off\n");

 		usb_remove_hcd(hcd);
 		/* HCD core reset all bits of PORTSC. select ULPI phy */
 		writel_relaxed(0x80000000, USB_PORTSC);

 		if (pdata->setup_gpio)
 			pdata->setup_gpio(OTG_STATE_UNDEFINED);

 		if (pdata->otg_control == OTG_PHY_CONTROL)
 			ulpi_write(otg->phy, OTG_COMP_DISABLE,
 				ULPI_CLR(ULPI_PWR_CLK_MNG_REG));
 	}
 }

 static int msm_otg_usbdev_notify(struct notifier_block *self,
 			unsigned long action, void *priv)
 {
 	struct msm_otg *motg = container_of(self, struct msm_otg, usbdev_nb);
 	struct usb_otg *otg = motg->phy.otg;
 	struct usb_device *udev = priv;

 	if (action == USB_BUS_ADD || action == USB_BUS_REMOVE)
 		goto out;

 	if (udev->bus != otg->host)
 		goto out;
 	/*
 	 * Interested in devices connected directly to the root hub.
 	 * ACA dock can supply IDEV_CHG irrespective devices connected
 	 * on the accessory port.
 	 */
 	if (!udev->parent || udev->parent->parent ||
 			motg->chg_type == USB_ACA_DOCK_CHARGER)
 		goto out;

 	switch (action) {
 	case USB_DEVICE_ADD:
 		if (aca_enabled())
 			usb_disable_autosuspend(udev);
 		if (otg->phy->state == OTG_STATE_A_WAIT_BCON) {
 			pr_debug("B_CONN set\n");
 			set_bit(B_CONN, &motg->inputs);
 			msm_otg_del_timer(motg);
 			otg->phy->state = OTG_STATE_A_HOST;
 			/*
 			 * OTG PET: A-device must end session within
 			 * 10 sec after PET enumeration.
 			 */
 			if (udev->quirks & USB_QUIRK_OTG_PET)
 				msm_otg_start_timer(motg, TA_TST_MAINT,
 						A_TST_MAINT);
 		}
 		/* fall through */
 	case USB_DEVICE_CONFIG:
 		if (udev->actconfig)
 			motg->mA_port = udev->actconfig->desc.bMaxPower * 2;
 		else
 			motg->mA_port = IUNIT;
 		if (otg->phy->state == OTG_STATE_B_HOST)
 			msm_otg_del_timer(motg);
 		break;
 	case USB_DEVICE_REMOVE:
 		if ((otg->phy->state == OTG_STATE_A_HOST) ||
 			(otg->phy->state == OTG_STATE_A_SUSPEND)) {
 			pr_debug("B_CONN clear\n");
 			clear_bit(B_CONN, &motg->inputs);
 			/*
 			 * OTG PET: A-device must end session after
 			 * PET disconnection if it is enumerated
 			 * with bcdDevice[0] = 1. USB core sets
 			 * bus->otg_vbus_off for us. clear it here.
 			 */
 			if (udev->bus->otg_vbus_off) {
 				udev->bus->otg_vbus_off = 0;
 				set_bit(A_BUS_DROP, &motg->inputs);
 			}
 			queue_work(system_nrt_wq, &motg->sm_work);
 		}
 	default:
 		break;
 	}
 	if (test_bit(ID_A, &motg->inputs))
 		msm_otg_notify_charger(motg, IDEV_ACA_CHG_MAX -
 				motg->mA_port);
 out:
 	return NOTIFY_OK;
 }

 static void msm_hsusb_vbus_power(struct msm_otg *motg, bool on)
 {
 	int ret;
 	static bool vbus_is_on;

 	if (vbus_is_on == on)
 		return;

 	if (motg->pdata->vbus_power) {
 		ret = motg->pdata->vbus_power(on);
 		if (!ret)
 			vbus_is_on = on;
 		return;
 	}

 	if (!vbus_otg) {
 		pr_err("vbus_otg is NULL.");
 		return;
 	}

 	/*
 	 * if entering host mode tell the charger to not draw any current
 	 * from usb before turning on the boost.
 	 * if exiting host mode disable the boost before enabling to draw
 	 * current from the source.
 	 */
 	if (on) {
 		msm_otg_notify_host_mode(motg, on);
 		ret = regulator_enable(vbus_otg);
 		if (ret) {
 			pr_err("unable to enable vbus_otg\n");
 			return;
 		}
 		vbus_is_on = true;
 	} else {
 		ret = regulator_disable(vbus_otg);
 		if (ret) {
 			pr_err("unable to disable vbus_otg\n");
 			return;
 		}
 		msm_otg_notify_host_mode(motg, on);
 		vbus_is_on = false;
 	}
 }

 static int msm_otg_set_host(struct usb_otg *otg, struct usb_bus *host)
 {
 	struct msm_otg *motg = container_of(otg->phy, struct msm_otg, phy);
 	struct usb_hcd *hcd;

 	/*
 	 * Fail host registration if this board can support
 	 * only peripheral configuration.
 	 */
 	if (motg->pdata->mode == USB_PERIPHERAL) {
 		dev_info(otg->phy->dev, "Host mode is not supported\n");
 		return -ENODEV;
 	}

 	if (!motg->pdata->vbus_power && host) {
 		vbus_otg = devm_regulator_get(motg->phy.dev, "vbus_otg");
 		if (IS_ERR(vbus_otg)) {
 			pr_err("Unable to get vbus_otg\n");
 			return PTR_ERR(vbus_otg);
 		}
 	}

 	if (!host) {
 		if (otg->phy->state == OTG_STATE_A_HOST) {
 			pm_runtime_get_sync(otg->phy->dev);
 			usb_unregister_notify(&motg->usbdev_nb);
 			msm_otg_start_host(otg, 0);
 			msm_hsusb_vbus_power(motg, 0);
 			otg->host = NULL;
 			otg->phy->state = OTG_STATE_UNDEFINED;
 			queue_work(system_nrt_wq, &motg->sm_work);
 		} else {
 			otg->host = NULL;
 		}

 		return 0;
 	}

 	hcd = bus_to_hcd(host);
 	hcd->power_budget = motg->pdata->power_budget;

 #ifdef CONFIG_USB_OTG
 	host->otg_port = 1;
 #endif
 	motg->usbdev_nb.notifier_call = msm_otg_usbdev_notify;
 	usb_register_notify(&motg->usbdev_nb);
 	otg->host = host;
 	dev_dbg(otg->phy->dev, "host driver registered w/ tranceiver\n");

 	/*
 	 * Kick the state machine work, if peripheral is not supported
 	 * or peripheral is already registered with us.
 	 */
 	if (motg->pdata->mode == USB_HOST || otg->gadget) {
 		pm_runtime_get_sync(otg->phy->dev);
 		queue_work(system_nrt_wq, &motg->sm_work);
 	}

 	return 0;
 }

 static void msm_otg_start_peripheral(struct usb_otg *otg, int on)
 {
 	struct msm_otg *motg = container_of(otg->phy, struct msm_otg, phy);
 	struct msm_otg_platform_data *pdata = motg->pdata;

 	if (!otg->gadget)
 		return;

 	if (on) {
 		dev_dbg(otg->phy->dev, "gadget on\n");
 		/*
 		 * Some boards have a switch cotrolled by gpio
 		 * to enable/disable internal HUB. Disable internal
 		 * HUB before kicking the gadget.
 		 */
 		if (pdata->setup_gpio)
 			pdata->setup_gpio(OTG_STATE_B_PERIPHERAL);

 		/* Configure BUS performance parameters for MAX bandwidth */
 		if (debug_bus_voting_enabled)
 			msm_otg_bus_vote(motg, USB_MAX_PERF_VOTE);

 		usb_gadget_vbus_connect(otg->gadget);
 	} else {
 		dev_dbg(otg->phy->dev, "gadget off\n");
 		usb_gadget_vbus_disconnect(otg->gadget);
 		/* Configure BUS performance parameters to default */
 		msm_otg_bus_vote(motg, USB_MIN_PERF_VOTE);
 		if (pdata->setup_gpio)
 			pdata->setup_gpio(OTG_STATE_UNDEFINED);
 	}
 }

 static int msm_otg_set_peripheral(struct usb_otg *otg,
 					struct usb_gadget *gadget)
 {
 	struct msm_otg *motg = container_of(otg->phy, struct msm_otg, phy);

 	/*
 	 * Fail peripheral registration if this board can support
 	 * only host configuration.
 	 */
 	if (motg->pdata->mode == USB_HOST) {
 		dev_info(otg->phy->dev, "Peripheral mode is not supported\n");
 		return -ENODEV;
 	}

 	if (!gadget) {
 		if (otg->phy->state == OTG_STATE_B_PERIPHERAL) {
 			pm_runtime_get_sync(otg->phy->dev);
 			msm_otg_start_peripheral(otg, 0);
 			otg->gadget = NULL;
 			otg->phy->state = OTG_STATE_UNDEFINED;
 			queue_work(system_nrt_wq, &motg->sm_work);
 		} else {
 			otg->gadget = NULL;
 		}

 		return 0;
 	}
 	otg->gadget = gadget;
 	dev_dbg(otg->phy->dev, "peripheral driver registered w/ tranceiver\n");

 	/*
 	 * Kick the state machine work, if host is not supported
 	 * or host is already registered with us.
 	 */
 	if (motg->pdata->mode == USB_PERIPHERAL || otg->host) {
 		pm_runtime_get_sync(otg->phy->dev);
 		queue_work(system_nrt_wq, &motg->sm_work);
 	}

 	return 0;
 }

 static bool msm_otg_read_pmic_id_state(struct msm_otg *motg)
 {
 	unsigned long flags;
 	int id;

 	if (!motg->pdata->pmic_id_irq)
 		return -ENODEV;

 	local_irq_save(flags);
 	id = irq_read_line(motg->pdata->pmic_id_irq);
 	local_irq_restore(flags);

 	/*
 	 * If we can not read ID line state for some reason, treat
 	 * it as float. This would prevent MHL discovery and kicking
 	 * host mode unnecessarily.
 	 */
 	return !!id;
 }

 static int msm_otg_mhl_register_callback(struct msm_otg *motg,
 						void (*callback)(int on))
 {
 	struct usb_phy *phy = &motg->phy;
 	int ret;

 	if (!motg->pdata->mhl_enable) {
 		dev_dbg(phy->dev, "MHL feature not enabled\n");
 		return -ENODEV;
 	}

 	if (motg->pdata->otg_control != OTG_PMIC_CONTROL ||
 			!motg->pdata->pmic_id_irq) {
 		dev_dbg(phy->dev, "MHL can not be supported without PMIC Id\n");
 		return -ENODEV;
 	}

 	if (!motg->pdata->mhl_dev_name) {
 		dev_dbg(phy->dev, "MHL device name does not exist.\n");
 		return -ENODEV;
 	}

 	if (callback)
 		ret = mhl_register_callback(motg->pdata->mhl_dev_name,
 								callback);
 	else
 		ret = mhl_unregister_callback(motg->pdata->mhl_dev_name);

 	if (ret)
 		dev_dbg(phy->dev, "mhl_register_callback(%s) return error=%d\n",
 						motg->pdata->mhl_dev_name, ret);
 	else
 		motg->mhl_enabled = true;

 	return ret;
 }

 static void msm_otg_mhl_notify_online(int on)
 {
 	struct msm_otg *motg = the_msm_otg;
 	struct usb_phy *phy = &motg->phy;
 	bool queue = false;

 	dev_dbg(phy->dev, "notify MHL %s%s\n", on ? "" : "dis", "connected");

 	if (on) {
 		set_bit(MHL, &motg->inputs);
 	} else {
 		clear_bit(MHL, &motg->inputs);
 		queue = true;
 	}

 	if (queue && phy->state != OTG_STATE_UNDEFINED)
 		schedule_work(&motg->sm_work);
 }

 static bool msm_otg_is_mhl(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	int is_mhl, ret;

 	ret = mhl_device_discovery(motg->pdata->mhl_dev_name, &is_mhl);
 	if (ret || is_mhl != MHL_DISCOVERY_RESULT_MHL) {
 		/*
 		 * MHL driver calls our callback saying that MHL connected
 		 * if RID_GND is detected.  But at later part of discovery
 		 * it may figure out MHL is not connected and returns
 		 * false. Hence clear MHL input here.
 		 */
 		clear_bit(MHL, &motg->inputs);
 		dev_dbg(phy->dev, "MHL device not found\n");
 		return false;
 	}

 	set_bit(MHL, &motg->inputs);
 	dev_dbg(phy->dev, "MHL device found\n");
 	return true;
 }

 static bool msm_chg_mhl_detect(struct msm_otg *motg)
 {
 	bool ret, id;

 	if (!motg->mhl_enabled)
 		return false;

 	id = msm_otg_read_pmic_id_state(motg);

 	if (id)
 		return false;

 	mhl_det_in_progress = true;
 	ret = msm_otg_is_mhl(motg);
 	mhl_det_in_progress = false;

 	return ret;
 }

 static void msm_otg_chg_check_timer_func(unsigned long data)
 {
 	struct msm_otg *motg = (struct msm_otg *) data;
 	struct usb_otg *otg = motg->phy.otg;

 	if (atomic_read(&motg->in_lpm) ||
 		!test_bit(B_SESS_VLD, &motg->inputs) ||
 		otg->phy->state != OTG_STATE_B_PERIPHERAL ||
 		otg->gadget->speed != USB_SPEED_UNKNOWN) {
 		dev_dbg(otg->phy->dev, "Nothing to do in chg_check_timer\n");
 		return;
 	}

 	if ((readl_relaxed(USB_PORTSC) & PORTSC_LS) == PORTSC_LS) {
 		dev_dbg(otg->phy->dev, "DCP is detected as SDP\n");
 		set_bit(B_FALSE_SDP, &motg->inputs);
 		queue_work(system_nrt_wq, &motg->sm_work);
 	}
 }

 static bool msm_chg_aca_detect(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 int_sts;
 	bool ret = false;

 	if (!aca_enabled())
 		goto out;

 	if (motg->pdata->phy_type == CI_45NM_INTEGRATED_PHY)
 		goto out;

 	int_sts = ulpi_read(phy, 0x87);
 	switch (int_sts & 0x1C) {
 	case 0x08:
 		if (!test_and_set_bit(ID_A, &motg->inputs)) {
 			dev_dbg(phy->dev, "ID_A\n");
 			motg->chg_type = USB_ACA_A_CHARGER;
 			motg->chg_state = USB_CHG_STATE_DETECTED;
 			clear_bit(ID_B, &motg->inputs);
 			clear_bit(ID_C, &motg->inputs);
 			set_bit(ID, &motg->inputs);
 			ret = true;
 		}
 		break;
 	case 0x0C:
 		if (!test_and_set_bit(ID_B, &motg->inputs)) {
 			dev_dbg(phy->dev, "ID_B\n");
 			motg->chg_type = USB_ACA_B_CHARGER;
 			motg->chg_state = USB_CHG_STATE_DETECTED;
 			clear_bit(ID_A, &motg->inputs);
 			clear_bit(ID_C, &motg->inputs);
 			set_bit(ID, &motg->inputs);
 			ret = true;
 		}
 		break;
 	case 0x10:
 		if (!test_and_set_bit(ID_C, &motg->inputs)) {
 			dev_dbg(phy->dev, "ID_C\n");
 			motg->chg_type = USB_ACA_C_CHARGER;
 			motg->chg_state = USB_CHG_STATE_DETECTED;
 			clear_bit(ID_A, &motg->inputs);
 			clear_bit(ID_B, &motg->inputs);
 			set_bit(ID, &motg->inputs);
 			ret = true;
 		}
 		break;
 	case 0x04:
 		if (test_and_clear_bit(ID, &motg->inputs)) {
 			dev_dbg(phy->dev, "ID_GND\n");
 			motg->chg_type = USB_INVALID_CHARGER;
 			motg->chg_state = USB_CHG_STATE_UNDEFINED;
 			clear_bit(ID_A, &motg->inputs);
 			clear_bit(ID_B, &motg->inputs);
 			clear_bit(ID_C, &motg->inputs);
 			ret = true;
 		}
 		break;
 	default:
 		ret = test_and_clear_bit(ID_A, &motg->inputs) |
 			test_and_clear_bit(ID_B, &motg->inputs) |
 			test_and_clear_bit(ID_C, &motg->inputs) |
 			!test_and_set_bit(ID, &motg->inputs);
 		if (ret) {
 			dev_dbg(phy->dev, "ID A/B/C/GND is no more\n");
 			motg->chg_type = USB_INVALID_CHARGER;
 			motg->chg_state = USB_CHG_STATE_UNDEFINED;
 		}
 	}
 out:
 	return ret;
 }

 static void msm_chg_enable_aca_det(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;

 	if (!aca_enabled())
 		return;

 	switch (motg->pdata->phy_type) {
 	case SNPS_28NM_INTEGRATED_PHY:
 		/* Disable ID_GND in link and PHY */
 		writel_relaxed(readl_relaxed(USB_OTGSC) & ~(OTGSC_IDPU |
 				OTGSC_IDIE), USB_OTGSC);
 		ulpi_write(phy, 0x01, 0x0C);
 		ulpi_write(phy, 0x10, 0x0F);
 		ulpi_write(phy, 0x10, 0x12);
 		/* Disable PMIC ID pull-up */
 		pm8xxx_usb_id_pullup(0);
 		/* Enable ACA ID detection */
 		ulpi_write(phy, 0x20, 0x85);
 		aca_id_turned_on = true;
 		break;
 	default:
 		break;
 	}
 }

 static void msm_chg_enable_aca_intr(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;

 	if (!aca_enabled())
 		return;

 	switch (motg->pdata->phy_type) {
 	case SNPS_28NM_INTEGRATED_PHY:
 		/* Enable ACA Detection interrupt (on any RID change) */
 		ulpi_write(phy, 0x01, 0x94);
 		break;
 	default:
 		break;
 	}
 }

 static void msm_chg_disable_aca_intr(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;

 	if (!aca_enabled())
 		return;

 	switch (motg->pdata->phy_type) {
 	case SNPS_28NM_INTEGRATED_PHY:
 		ulpi_write(phy, 0x01, 0x95);
 		break;
 	default:
 		break;
 	}
 }

 static bool msm_chg_check_aca_intr(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	bool ret = false;

 	if (!aca_enabled())
 		return ret;

 	switch (motg->pdata->phy_type) {
 	case SNPS_28NM_INTEGRATED_PHY:
 		if (ulpi_read(phy, 0x91) & 1) {
 			dev_dbg(phy->dev, "RID change\n");
 			ulpi_write(phy, 0x01, 0x92);
 			ret = msm_chg_aca_detect(motg);
 		}
 	default:
 		break;
 	}
 	return ret;
 }

 static void msm_otg_id_timer_func(unsigned long data)
 {
 	struct msm_otg *motg = (struct msm_otg *) data;

 	if (!aca_enabled())
 		return;

 	if (atomic_read(&motg->in_lpm)) {
 		dev_dbg(motg->phy.dev, "timer: in lpm\n");
 		return;
 	}

 	if (motg->phy.state == OTG_STATE_A_SUSPEND)
 		goto out;

 	if (msm_chg_check_aca_intr(motg)) {
 		dev_dbg(motg->phy.dev, "timer: aca work\n");
 		queue_work(system_nrt_wq, &motg->sm_work);
 	}

 out:
 	if (!test_bit(ID, &motg->inputs) || test_bit(ID_A, &motg->inputs))
 		mod_timer(&motg->id_timer, ID_TIMER_FREQ);
 }

 static bool msm_chg_check_secondary_det(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 chg_det;
 	bool ret = false;

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x34);
 		ret = chg_det & (1 << 4);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x87);
 		ret = chg_det & 1;
 		break;
 	default:
 		break;
 	}
 	return ret;
 }

 static void msm_chg_enable_secondary_det(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 chg_det;

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x34);
 		/* Turn off charger block */
 		chg_det |= ~(1 << 1);
 		ulpi_write(phy, chg_det, 0x34);
 		udelay(20);
 		/* control chg block via ULPI */
 		chg_det &= ~(1 << 3);
 		ulpi_write(phy, chg_det, 0x34);
 		/* put it in host mode for enabling D- source */
 		chg_det &= ~(1 << 2);
 		ulpi_write(phy, chg_det, 0x34);
 		/* Turn on chg detect block */
 		chg_det &= ~(1 << 1);
 		ulpi_write(phy, chg_det, 0x34);
 		udelay(20);
 		/* enable chg detection */
 		chg_det &= ~(1 << 0);
 		ulpi_write(phy, chg_det, 0x34);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		/*
 		 * Configure DM as current source, DP as current sink
 		 * and enable battery charging comparators.
 		 */
 		ulpi_write(phy, 0x8, 0x85);
 		ulpi_write(phy, 0x2, 0x85);
 		ulpi_write(phy, 0x1, 0x85);
 		break;
 	default:
 		break;
 	}
 }

 static bool msm_chg_check_primary_det(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 chg_det;
 	bool ret = false;

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x34);
 		ret = chg_det & (1 << 4);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x87);
 		ret = chg_det & 1;
 		/* Turn off VDP_SRC */
 		ulpi_write(phy, 0x3, 0x86);
 		msleep(20);
 		break;
 	default:
 		break;
 	}
 	return ret;
 }

 static void msm_chg_enable_primary_det(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 chg_det;

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x34);
 		/* enable chg detection */
 		chg_det &= ~(1 << 0);
 		ulpi_write(phy, chg_det, 0x34);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		/*
 		 * Configure DP as current source, DM as current sink
 		 * and enable battery charging comparators.
 		 */
 		ulpi_write(phy, 0x2, 0x85);
 		ulpi_write(phy, 0x1, 0x85);
 		break;
 	default:
 		break;
 	}
 }

 static bool msm_chg_check_dcd(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 line_state;
 	bool ret = false;

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		line_state = ulpi_read(phy, 0x15);
 		ret = !(line_state & 1);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		line_state = ulpi_read(phy, 0x87);
 		ret = line_state & 2;
 		break;
 	default:
 		break;
 	}
 	return ret;
 }

 static void msm_chg_disable_dcd(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 chg_det;

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x34);
 		chg_det &= ~(1 << 5);
 		ulpi_write(phy, chg_det, 0x34);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		ulpi_write(phy, 0x10, 0x86);
 		break;
 	default:
 		break;
 	}
 }

 static void msm_chg_enable_dcd(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 chg_det;

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x34);
 		/* Turn on D+ current source */
 		chg_det |= (1 << 5);
 		ulpi_write(phy, chg_det, 0x34);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		/* Data contact detection enable */
 		ulpi_write(phy, 0x10, 0x85);
 		break;
 	default:
 		break;
 	}
 }

 static void msm_chg_block_on(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 func_ctrl, chg_det;

 	/* put the controller in non-driving mode */
 	func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
 	func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
 	func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NONDRIVING;
 	ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x34);
 		/* control chg block via ULPI */
 		chg_det &= ~(1 << 3);
 		ulpi_write(phy, chg_det, 0x34);
 		/* Turn on chg detect block */
 		chg_det &= ~(1 << 1);
 		ulpi_write(phy, chg_det, 0x34);
 		udelay(20);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		/* disable DP and DM pull down resistors */
 		ulpi_write(phy, 0x6, 0xC);
 		/* Clear charger detecting control bits */
 		ulpi_write(phy, 0x1F, 0x86);
 		/* Clear alt interrupt latch and enable bits */
 		ulpi_write(phy, 0x1F, 0x92);
 		ulpi_write(phy, 0x1F, 0x95);
 		udelay(100);
 		break;
 	default:
 		break;
 	}
 }

 static void msm_chg_block_off(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	u32 func_ctrl, chg_det;

 	switch (motg->pdata->phy_type) {
 	case CI_45NM_INTEGRATED_PHY:
 		chg_det = ulpi_read(phy, 0x34);
 		/* Turn off charger block */
 		chg_det |= ~(1 << 1);
 		ulpi_write(phy, chg_det, 0x34);
 		break;
 	case SNPS_28NM_INTEGRATED_PHY:
 		/* Clear charger detecting control bits */
 		ulpi_write(phy, 0x3F, 0x86);
 		/* Clear alt interrupt latch and enable bits */
 		ulpi_write(phy, 0x1F, 0x92);
 		ulpi_write(phy, 0x1F, 0x95);
 		/* re-enable DP and DM pull down resistors */
 		ulpi_write(phy, 0x6, 0xB);
 		break;
 	default:
 		break;
 	}

 	/* put the controller in normal mode */
 	func_ctrl = ulpi_read(phy, ULPI_FUNC_CTRL);
 	func_ctrl &= ~ULPI_FUNC_CTRL_OPMODE_MASK;
 	func_ctrl |= ULPI_FUNC_CTRL_OPMODE_NORMAL;
 	ulpi_write(phy, func_ctrl, ULPI_FUNC_CTRL);
 }

 static const char *chg_to_string(enum usb_chg_type chg_type)
 {
 	switch (chg_type) {
 	case USB_SDP_CHARGER:		return "USB_SDP_CHARGER";
 	case USB_DCP_CHARGER:		return "USB_DCP_CHARGER";
 	case USB_CDP_CHARGER:		return "USB_CDP_CHARGER";
 	case USB_ACA_A_CHARGER:		return "USB_ACA_A_CHARGER";
 	case USB_ACA_B_CHARGER:		return "USB_ACA_B_CHARGER";
 	case USB_ACA_C_CHARGER:		return "USB_ACA_C_CHARGER";
 	case USB_ACA_DOCK_CHARGER:	return "USB_ACA_DOCK_CHARGER";
 	case USB_PROPRIETARY_CHARGER:	return "USB_PROPRIETARY_CHARGER";
 	case USB_FLOATED_CHARGER:	return "USB_FLOATED_CHARGER";
 	default:			return "INVALID_CHARGER";
 	}
 }

 #define MSM_CHG_DCD_TIMEOUT		(750 * HZ/1000) /* 750 msec */
 #define MSM_CHG_DCD_POLL_TIME		(50 * HZ/1000) /* 50 msec */
 #define MSM_CHG_PRIMARY_DET_TIME	(50 * HZ/1000) /* TVDPSRC_ON */
 #define MSM_CHG_SECONDARY_DET_TIME	(50 * HZ/1000) /* TVDMSRC_ON */
 static void msm_chg_detect_work(struct work_struct *w)
 {
 	struct msm_otg *motg = container_of(w, struct msm_otg, chg_work.work);
 	struct usb_phy *phy = &motg->phy;
 	bool is_dcd = false, tmout, vout, is_aca;
 	static bool dcd;
 	u32 line_state, dm_vlgc;
 	unsigned long delay;

 	dev_dbg(phy->dev, "chg detection work\n");

 	if (test_bit(MHL, &motg->inputs)) {
 		dev_dbg(phy->dev, "detected MHL, escape chg detection work\n");
 		return;
 	}

 	switch (motg->chg_state) {
 	case USB_CHG_STATE_UNDEFINED:
 		msm_chg_block_on(motg);
 		msm_chg_enable_dcd(motg);
 		msm_chg_enable_aca_det(motg);
 		motg->chg_state = USB_CHG_STATE_WAIT_FOR_DCD;
 		motg->dcd_time = 0;
 		delay = MSM_CHG_DCD_POLL_TIME;
 		break;
 	case USB_CHG_STATE_WAIT_FOR_DCD:
 		if (msm_chg_mhl_detect(motg)) {
 			msm_chg_block_off(motg);
 			motg->chg_state = USB_CHG_STATE_DETECTED;
 			motg->chg_type = USB_INVALID_CHARGER;
 			queue_work(system_nrt_wq, &motg->sm_work);
 			return;
 		}
 		is_aca = msm_chg_aca_detect(motg);
 		if (is_aca) {
 			/*
 			 * ID_A can be ACA dock too. continue
 			 * primary detection after DCD.
 			 */
 			if (test_bit(ID_A, &motg->inputs)) {
 				motg->chg_state = USB_CHG_STATE_WAIT_FOR_DCD;
 			} else {
 				delay = 0;
 				break;
 			}
 		}
 		is_dcd = msm_chg_check_dcd(motg);
 		motg->dcd_time += MSM_CHG_DCD_POLL_TIME;
 		tmout = motg->dcd_time >= MSM_CHG_DCD_TIMEOUT;
 		if (is_dcd || tmout) {
 			if (is_dcd)
 				dcd = true;
 			else
 				dcd = false;
 			msm_chg_disable_dcd(motg);
 			msm_chg_enable_primary_det(motg);
 			delay = MSM_CHG_PRIMARY_DET_TIME;
 			motg->chg_state = USB_CHG_STATE_DCD_DONE;
 		} else {
 			delay = MSM_CHG_DCD_POLL_TIME;
 		}
 		break;
 	case USB_CHG_STATE_DCD_DONE:
 		vout = msm_chg_check_primary_det(motg);
 		line_state = readl_relaxed(USB_PORTSC) & PORTSC_LS;
 		dm_vlgc = line_state & PORTSC_LS_DM;
 		if (vout && !dm_vlgc) { /* VDAT_REF < DM < VLGC */
 			if (test_bit(ID_A, &motg->inputs)) {
 				motg->chg_type = USB_ACA_DOCK_CHARGER;
 				motg->chg_state = USB_CHG_STATE_DETECTED;
 				delay = 0;
 				break;
 			}
 			if (line_state) { /* DP > VLGC */
 				motg->chg_type = USB_PROPRIETARY_CHARGER;
 				motg->chg_state = USB_CHG_STATE_DETECTED;
 				delay = 0;
 			} else {
 				msm_chg_enable_secondary_det(motg);
 				delay = MSM_CHG_SECONDARY_DET_TIME;
 				motg->chg_state = USB_CHG_STATE_PRIMARY_DONE;
 			}
 		} else { /* DM < VDAT_REF || DM > VLGC */
 			if (test_bit(ID_A, &motg->inputs)) {
 				motg->chg_type = USB_ACA_A_CHARGER;
 				motg->chg_state = USB_CHG_STATE_DETECTED;
 				delay = 0;
 				break;
 			}

 			if (line_state) /* DP > VLGC or/and DM > VLGC */
 				motg->chg_type = USB_PROPRIETARY_CHARGER;
 			else if (!dcd && floated_charger_enable)
 				motg->chg_type = USB_FLOATED_CHARGER;
 			else
 				motg->chg_type = USB_SDP_CHARGER;

 			motg->chg_state = USB_CHG_STATE_DETECTED;
 			delay = 0;
 		}
 		break;
 	case USB_CHG_STATE_PRIMARY_DONE:
 		vout = msm_chg_check_secondary_det(motg);
 		if (vout)
 			motg->chg_type = USB_DCP_CHARGER;
 		else
 			motg->chg_type = USB_CDP_CHARGER;
 		motg->chg_state = USB_CHG_STATE_SECONDARY_DONE;
 		/* fall through */
 	case USB_CHG_STATE_SECONDARY_DONE:
 		motg->chg_state = USB_CHG_STATE_DETECTED;
 	case USB_CHG_STATE_DETECTED:
 		/*
 		 * Notify the charger type to power supply
 		 * owner as soon as we determine the charger.
 		 */
 		msm_otg_notify_chg_type(motg);
 		msm_chg_block_off(motg);
 		msm_chg_enable_aca_det(motg);
 		/*
 		 * Spurious interrupt is seen after enabling ACA detection
 		 * due to which charger detection fails in case of PET.
 		 * Add delay of 100 microsec to avoid that.
 		 */
 		udelay(100);
 		msm_chg_enable_aca_intr(motg);
 		dev_dbg(phy->dev, "chg_type = %s\n",
 			chg_to_string(motg->chg_type));
 		queue_work(system_nrt_wq, &motg->sm_work);
 		return;
 	default:
 		return;
 	}

 	queue_delayed_work(system_nrt_wq, &motg->chg_work, delay);
 }

 /*
  * We support OTG, Peripheral only and Host only configurations. In case
  * of OTG, mode switch (host-->peripheral/peripheral-->host) can happen
  * via Id pin status or user request (debugfs). Id/BSV interrupts are not
  * enabled when switch is controlled by user and default mode is supplied
  * by board file, which can be changed by userspace later.
  */
 static void msm_otg_init_sm(struct msm_otg *motg)
 {
 	struct msm_otg_platform_data *pdata = motg->pdata;
 	u32 otgsc = readl(USB_OTGSC);

 	switch (pdata->mode) {
 	case USB_OTG:
 		if (pdata->otg_control == OTG_USER_CONTROL) {
 			if (pdata->default_mode == USB_HOST) {
 				clear_bit(ID, &motg->inputs);
 			} else if (pdata->default_mode == USB_PERIPHERAL) {
 				set_bit(ID, &motg->inputs);
 				set_bit(B_SESS_VLD, &motg->inputs);
 			} else {
 				set_bit(ID, &motg->inputs);
 				clear_bit(B_SESS_VLD, &motg->inputs);
 			}
 		} else if (pdata->otg_control == OTG_PHY_CONTROL) {
 			if (otgsc & OTGSC_ID) {
 				set_bit(ID, &motg->inputs);
 			} else {
 				clear_bit(ID, &motg->inputs);
 				set_bit(A_BUS_REQ, &motg->inputs);
 			}
 			if (otgsc & OTGSC_BSV)
 				set_bit(B_SESS_VLD, &motg->inputs);
 			else
 				clear_bit(B_SESS_VLD, &motg->inputs);
 		} else if (pdata->otg_control == OTG_PMIC_CONTROL) {
 			if (pdata->pmic_id_irq) {
 				if (msm_otg_read_pmic_id_state(motg))
 					set_bit(ID, &motg->inputs);
 				else
 					clear_bit(ID, &motg->inputs);
 			}
 			/*
 			 * VBUS initial state is reported after PMIC
 			 * driver initialization. Wait for it.
 			 */
 			wait_for_completion(&pmic_vbus_init);
 		}
 		break;
 	case USB_HOST:
 		clear_bit(ID, &motg->inputs);
 		break;
 	case USB_PERIPHERAL:
 		set_bit(ID, &motg->inputs);
 		if (pdata->otg_control == OTG_PHY_CONTROL) {
 			if (otgsc & OTGSC_BSV)
 				set_bit(B_SESS_VLD, &motg->inputs);
 			else
 				clear_bit(B_SESS_VLD, &motg->inputs);
 		} else if (pdata->otg_control == OTG_PMIC_CONTROL) {
 			/*
 			 * VBUS initial state is reported after PMIC
 			 * driver initialization. Wait for it.
 			 */
 			wait_for_completion(&pmic_vbus_init);
 		}
 		break;
 	default:
 		break;
 	}
 }

 static void msm_otg_wait_for_ext_chg_done(struct msm_otg *motg)
 {
 	struct usb_phy *phy = &motg->phy;
 	unsigned long t;

 	/*
 	 * Defer next cable connect event till external charger
 	 * detection is completed.
 	 */

 	if (motg->ext_chg_active) {

 		pr_debug("before msm_otg ext chg wait\n");

 		t = wait_for_completion_timeout(&motg->ext_chg_wait,
 				msecs_to_jiffies(3000));
 		if (!t)
 			pr_err("msm_otg ext chg wait timeout\n");
 		else
 			pr_debug("msm_otg ext chg wait done\n");
 	}

 	if (motg->ext_chg_opened) {
 		if (phy->flags & ENABLE_DP_MANUAL_PULLUP) {
 			ulpi_write(phy, ULPI_MISC_A_VBUSVLDEXT |
 					ULPI_MISC_A_VBUSVLDEXTSEL,
 					ULPI_CLR(ULPI_MISC_A));
 		}
 		/* clear charging register bits */
 		ulpi_write(phy, 0x3F, 0x86);
 		/* re-enable DP and DM pull-down resistors*/
 		ulpi_write(phy, 0x6, 0xB);
 	}
 }

 static void msm_otg_sm_work(struct work_struct *w)
 {
 	struct msm_otg *motg = container_of(w, struct msm_otg, sm_work);
 	struct usb_otg *otg = motg->phy.otg;
 	bool work = 0, srp_reqd, dcp;

 	pm_runtime_resume(otg->phy->dev);
 	pr_debug("%s work\n", otg_state_string(otg->phy->state));
 	switch (otg->phy->state) {
 	case OTG_STATE_UNDEFINED:
 		msm_otg_reset(otg->phy);
 		msm_otg_init_sm(motg);
 		if (!psy && legacy_power_supply) {
 			psy = power_supply_get_by_name("usb");

 			if (!psy)
 				pr_err("couldn't get usb power supply\n");
 		}

 		otg->phy->state = OTG_STATE_B_IDLE;
 		if (!test_bit(B_SESS_VLD, &motg->inputs) &&
 				test_bit(ID, &motg->inputs)) {
 			pm_runtime_put_noidle(otg->phy->dev);
 			pm_runtime_suspend(otg->phy->dev);
 			break;
 		}
 		/* FALL THROUGH */
 	case OTG_STATE_B_IDLE:
 		if (test_bit(MHL, &motg->inputs)) {
 			/* allow LPM */
 			pm_runtime_put_noidle(otg->phy->dev);
 			pm_runtime_suspend(otg->phy->dev);
 		} else if ((!test_bit(ID, &motg->inputs) ||
 				test_bit(ID_A, &motg->inputs)) && otg->host) {
 			pr_debug("!id || id_A\n");
 			if (msm_chg_mhl_detect(motg)) {
 				work = 1;
 				break;
 			}
 			clear_bit(B_BUS_REQ, &motg->inputs);
 			set_bit(A_BUS_REQ, &motg->inputs);
 			otg->phy->state = OTG_STATE_A_IDLE;
 			work = 1;
 		} else if (test_bit(B_SESS_VLD, &motg->inputs)) {
 			pr_debug("b_sess_vld\n");
 			switch (motg->chg_state) {
 			case USB_CHG_STATE_UNDEFINED:
 				msm_chg_detect_work(&motg->chg_work.work);
 				break;
 			case USB_CHG_STATE_DETECTED:
 				switch (motg->chg_type) {
 				case USB_DCP_CHARGER:
 					/* Enable VDP_SRC */
 					ulpi_write(otg->phy, 0x2, 0x85);
 					if (motg->ext_chg_opened) {
 						init_completion(
 							&motg->ext_chg_wait);
 						motg->ext_chg_active = true;
 					}
 					/* fall through */
 				case USB_PROPRIETARY_CHARGER:
 					msm_otg_notify_charger(motg,
 							IDEV_CHG_MAX);
 					pm_runtime_put_sync(otg->phy->dev);
 					break;
 				case USB_FLOATED_CHARGER:
 					msm_otg_notify_charger(motg,
 							IDEV_CHG_MAX);
 					pm_runtime_put_noidle(otg->phy->dev);
 					pm_runtime_suspend(otg->phy->dev);
 					break;
 				case USB_ACA_B_CHARGER:
 					msm_otg_notify_charger(motg,
 							IDEV_ACA_CHG_MAX);
 					/*
 					 * (ID_B --> ID_C) PHY_ALT interrupt can
 					 * not be detected in LPM.
 					 */
 					break;
 				case USB_CDP_CHARGER:
 					msm_otg_notify_charger(motg,
 							IDEV_CHG_MAX);
 					msm_otg_start_peripheral(otg, 1);
 					otg->phy->state =
 						OTG_STATE_B_PERIPHERAL;
 					break;
 				case USB_ACA_C_CHARGER:
 					msm_otg_notify_charger(motg,
 							IDEV_ACA_CHG_MAX);
 					msm_otg_start_peripheral(otg, 1);
 					otg->phy->state =
 						OTG_STATE_B_PERIPHERAL;
 					break;
 				case USB_SDP_CHARGER:
 					msm_otg_start_peripheral(otg, 1);
 					otg->phy->state =
 						OTG_STATE_B_PERIPHERAL;
 					mod_timer(&motg->chg_check_timer,
 							CHG_RECHECK_DELAY);
 					break;
 				default:
 					break;
 				}
 				break;
 			default:
 				break;
 			}
 		} else if (test_bit(B_BUS_REQ, &motg->inputs)) {
 			pr_debug("b_sess_end && b_bus_req\n");
 			if (msm_otg_start_srp(otg) < 0) {
 				clear_bit(B_BUS_REQ, &motg->inputs);
 				work = 1;
 				break;
 			}
 			otg->phy->state = OTG_STATE_B_SRP_INIT;
 			msm_otg_start_timer(motg, TB_SRP_FAIL, B_SRP_FAIL);
 			break;
 		} else {
 			pr_debug("chg_work cancel");
 			del_timer_sync(&motg->chg_check_timer);
 			clear_bit(B_FALSE_SDP, &motg->inputs);
 			clear_bit(A_BUS_REQ, &motg->inputs);
 			cancel_delayed_work_sync(&motg->chg_work);
 			dcp = (motg->chg_type == USB_DCP_CHARGER);
 			motg->chg_state = USB_CHG_STATE_UNDEFINED;
 			motg->chg_type = USB_INVALID_CHARGER;
 			msm_otg_notify_charger(motg, 0);
 			if (dcp) {
 				msm_otg_wait_for_ext_chg_done(motg);
 				/* Turn off VDP_SRC */
 				ulpi_write(otg->phy, 0x2, 0x86);
 			}
 			msm_otg_reset(otg->phy);
 			/*
 			 * There is a small window where ID interrupt
 			 * is not monitored during ID detection circuit
 			 * switch from ACA to PMIC.  Check ID state
 			 * before entering into low power mode.
 			 */
 			if (!msm_otg_read_pmic_id_state(motg)) {
 				pr_debug("process missed ID intr\n");
 				clear_bit(ID, &motg->inputs);
 				work = 1;
 				break;
 			}
 			pm_runtime_put_noidle(otg->phy->dev);
 			/*
 			 * Only if autosuspend was enabled in probe, it will be
 			 * used here. Otherwise, no delay will be used.
 			 */
 			pm_runtime_mark_last_busy(otg->phy->dev);
 			pm_runtime_autosuspend(otg->phy->dev);
 		}
 		break;
 	case OTG_STATE_B_SRP_INIT:
 		if (!test_bit(ID, &motg->inputs) ||
 				test_bit(ID_A, &motg->inputs) ||
 				test_bit(ID_C, &motg->inputs) ||
 				(test_bit(B_SESS_VLD, &motg->inputs) &&
 				!test_bit(ID_B, &motg->inputs))) {
 			pr_debug("!id || id_a/c || b_sess_vld+!id_b\n");
 			msm_otg_del_timer(motg);
 			otg->phy->state = OTG_STATE_B_IDLE;
 			/*
 			 * clear VBUSVLDEXTSEL and VBUSVLDEXT register
 			 * bits after SRP initiation.
 			 */
 			ulpi_write(otg->phy, 0x0, 0x98);
 			work = 1;
 		} else if (test_bit(B_SRP_FAIL, &motg->tmouts)) {
 			pr_debug("b_srp_fail\n");
 			pr_info("A-device did not respond to SRP\n");
 			clear_bit(B_BUS_REQ, &motg->inputs);
 			clear_bit(B_SRP_FAIL, &motg->tmouts);
 			otg_send_event(OTG_EVENT_NO_RESP_FOR_SRP);
 			ulpi_write(otg->phy, 0x0, 0x98);
 			otg->phy->state = OTG_STATE_B_IDLE;
 			motg->b_last_se0_sess = jiffies;
 			work = 1;
 		}
 		break;
 	case OTG_STATE_B_PERIPHERAL:
 		if (test_bit(B_SESS_VLD, &motg->inputs) &&
 				test_bit(B_FALSE_SDP, &motg->inputs)) {
 			pr_debug("B_FALSE_SDP\n");
 			msm_otg_start_peripheral(otg, 0);
 			motg->chg_type = USB_DCP_CHARGER;
 			clear_bit(B_FALSE_SDP, &motg->inputs);
 			otg->phy->state = OTG_STATE_B_IDLE;
 			work = 1;
 		} else if (!test_bit(ID, &motg->inputs) ||
 				test_bit(ID_A, &motg->inputs) ||
 				test_bit(ID_B, &motg->inputs) ||
 				!test_bit(B_SESS_VLD, &motg->inputs)) {
 			pr_debug("!id  || id_a/b || !b_sess_vld\n");
 			motg->chg_state = USB_CHG_STATE_UNDEFINED;
 			motg->chg_type = USB_INVALID_CHARGER;
 			msm_otg_notify_charger(motg, 0);
 			srp_reqd = otg->gadget->otg_srp_reqd;
 			msm_otg_start_peripheral(otg, 0);
 			if (test_bit(ID_B, &motg->inputs))
 				clear_bit(ID_B, &motg->inputs);
 			clear_bit(B_BUS_REQ, &motg->inputs);
 			otg->phy->state = OTG_STATE_B_IDLE;
 			motg->b_last_se0_sess = jiffies;
 			if (srp_reqd)
 				msm_otg_start_timer(motg,
 					TB_TST_SRP, B_TST_SRP);
 			else
 				work = 1;
 		} else if (test_bit(B_BUS_REQ, &motg->inputs) &&
 				otg->gadget->b_hnp_enable &&
 				test_bit(A_BUS_SUSPEND, &motg->inputs)) {
 			pr_debug("b_bus_req && b_hnp_en && a_bus_suspend\n");
 			msm_otg_start_timer(motg, TB_ASE0_BRST, B_ASE0_BRST);
 			/* D+ pullup should not be disconnected within 4msec
 			 * after A device suspends the bus. Otherwise PET will
 			 * fail the compliance test.
 			 */
 			udelay(1000);
 			msm_otg_start_peripheral(otg, 0);
 			otg->phy->state = OTG_STATE_B_WAIT_ACON;
 			/*
 			 * start HCD even before A-device enable
 			 * pull-up to meet HNP timings.
 			 */
 			otg->host->is_b_host = 1;
 			msm_otg_start_host(otg, 1);
 		} else if (test_bit(A_BUS_SUSPEND, &motg->inputs) &&
 				   test_bit(B_SESS_VLD, &motg->inputs)) {
 			pr_debug("a_bus_suspend && b_sess_vld\n");
 			if (motg->caps & ALLOW_LPM_ON_DEV_SUSPEND) {
 				pm_runtime_put_noidle(otg->phy->dev);
 				pm_runtime_suspend(otg->phy->dev);
 			}
 		} else if (test_bit(ID_C, &motg->inputs)) {
 			msm_otg_notify_charger(motg, IDEV_ACA_CHG_MAX);
 		}
 		break;
 	case OTG_STATE_B_WAIT_ACON:
 		if (!test_bit(ID, &motg->inputs) ||
 				test_bit(ID_A, &motg->inputs) ||
 				test_bit(ID_B, &motg->inputs) ||
 				!test_bit(B_SESS_VLD, &motg->inputs)) {
 			pr_debug("!id || id_a/b || !b_sess_vld\n");
 			msm_otg_del_timer(motg);
 			/*
 			 * A-device is physically disconnected during
 			 * HNP. Remove HCD.
 			 */
 			msm_otg_start_host(otg, 0);
 			otg->host->is_b_host = 0;

 			clear_bit(B_BUS_REQ, &motg->inputs);
 			clear_bit(A_BUS_SUSPEND, &motg->inputs);
 			motg->b_last_se0_sess = jiffies;
 			otg->phy->state = OTG_STATE_B_IDLE;
 			msm_otg_reset(otg->phy);
 			work = 1;
 		} else if (test_bit(A_CONN, &motg->inputs)) {
 			pr_debug("a_conn\n");
 			clear_bit(A_BUS_SUSPEND, &motg->inputs);
 			otg->phy->state = OTG_STATE_B_HOST;
 			/*
 			 * PET disconnects D+ pullup after reset is generated
 			 * by B device in B_HOST role which is not detected by
 			 * B device. As workaorund , start timer of 300msec
 			 * and stop timer if A device is enumerated else clear
 			 * A_CONN.
 			 */
 			msm_otg_start_timer(motg, TB_TST_CONFIG,
 						B_TST_CONFIG);
 		} else if (test_bit(B_ASE0_BRST, &motg->tmouts)) {
 			pr_debug("b_ase0_brst_tmout\n");
 			pr_info("B HNP fail:No response from A device\n");
 			msm_otg_start_host(otg, 0);
 			msm_otg_reset(otg->phy);
 			otg->host->is_b_host = 0;
 			clear_bit(B_ASE0_BRST, &motg->tmouts);
 			clear_bit(A_BUS_SUSPEND, &motg->inputs);
 			clear_bit(B_BUS_REQ, &motg->inputs);
 			otg_send_event(OTG_EVENT_HNP_FAILED);
 			otg->phy->state = OTG_STATE_B_IDLE;
 			work = 1;
 		} else if (test_bit(ID_C, &motg->inputs)) {
 			msm_otg_notify_charger(motg, IDEV_ACA_CHG_MAX);
 		}
 		break;
 	case OTG_STATE_B_HOST:
 		if (!test_bit(B_BUS_REQ, &motg->inputs) ||
 				!test_bit(A_CONN, &motg->inputs) ||
 				!test_bit(B_SESS_VLD, &motg->inputs)) {
 			pr_debug("!b_bus_req || !a_conn || !b_sess_vld\n");
 			clear_bit(A_CONN, &motg->inputs);
 			clear_bit(B_BUS_REQ, &motg->inputs);
 			msm_otg_start_host(otg, 0);
 			otg->host->is_b_host = 0;
 			otg->phy->state = OTG_STATE_B_IDLE;
 			msm_otg_reset(otg->phy);
 			work = 1;
 		} else if (test_bit(ID_C, &motg->inputs)) {
 			msm_otg_notify_charger(motg, IDEV_ACA_CHG_MAX);
 		}
 		break;
 	case OTG_STATE_A_IDLE:
 		otg->default_a = 1;
 		if (test_bit(ID, &motg->inputs) &&
 			!test_bit(ID_A, &motg->inputs)) {
 			pr_debug("id && !id_a\n");
 			otg->default_a = 0;
 			clear_bit(A_BUS_DROP, &motg->inputs);
 			otg->phy->state = OTG_STATE_B_IDLE;
 			del_timer_sync(&motg->id_timer);
 			msm_otg_link_reset(motg);
 			msm_chg_enable_aca_intr(motg);
 			msm_otg_notify_charger(motg, 0);
 			work = 1;
 		} else if (!test_bit(A_BUS_DROP, &motg->inputs) &&
 				(test_bit(A_SRP_DET, &motg->inputs) ||
 				 test_bit(A_BUS_REQ, &motg->inputs))) {
 			pr_debug("!a_bus_drop && (a_srp_det || a_bus_req)\n");

 			clear_bit(A_SRP_DET, &motg->inputs);
 			/* Disable SRP detection */
 			writel_relaxed((readl_relaxed(USB_OTGSC) &
 					~OTGSC_INTSTS_MASK) &
 					~OTGSC_DPIE, USB_OTGSC);

 			otg->phy->state = OTG_STATE_A_WAIT_VRISE;
 			/* VBUS should not be supplied before end of SRP pulse
 			 * generated by PET, if not complaince test fail.
 			 */
 			usleep_range(10000, 12000);
 			/* ACA: ID_A: Stop charging untill enumeration */
 			if (test_bit(ID_A, &motg->inputs))
 				msm_otg_notify_charger(motg, 0);
 			else
 				msm_hsusb_vbus_power(motg, 1);
 			msm_otg_start_timer(motg, TA_WAIT_VRISE, A_WAIT_VRISE);
 		} else {
 			pr_debug("No session requested\n");
 			clear_bit(A_BUS_DROP, &motg->inputs);
 			if (test_bit(ID_A, &motg->inputs)) {
 					msm_otg_notify_charger(motg,
 							IDEV_ACA_CHG_MAX);
 			} else if (!test_bit(ID, &motg->inputs)) {
 				msm_otg_notify_charger(motg, 0);
 				/*
 				 * A-device is not providing power on VBUS.
 				 * Enable SRP detection.
 				 */
 				writel_relaxed(0x13, USB_USBMODE);
 				writel_relaxed((readl_relaxed(USB_OTGSC) &
 						~OTGSC_INTSTS_MASK) |
 						OTGSC_DPIE, USB_OTGSC);
 				mb();
 			}
 		}
 		break;
 	case OTG_STATE_A_WAIT_VRISE:
 		if ((test_bit(ID, &motg->inputs) &&
 				!test_bit(ID_A, &motg->inputs)) ||
 				test_bit(A_BUS_DROP, &motg->inputs) ||
 				test_bit(A_WAIT_VRISE, &motg->tmouts)) {
 			pr_debug("id || a_bus_drop || a_wait_vrise_tmout\n");
 			clear_bit(A_BUS_REQ, &motg->inputs);
 			msm_otg_del_timer(motg);
 			msm_hsusb_vbus_power(motg, 0);
 			otg->phy->state = OTG_STATE_A_WAIT_VFALL;
 			msm_otg_start_timer(motg, TA_WAIT_VFALL, A_WAIT_VFALL);
 		} else if (test_bit(A_VBUS_VLD, &motg->inputs)) {
 			pr_debug("a_vbus_vld\n");
 			otg->phy->state = OTG_STATE_A_WAIT_BCON;
 			if (TA_WAIT_BCON > 0)
 				msm_otg_start_timer(motg, TA_WAIT_BCON,
 					A_WAIT_BCON);

 			/* Clear BSV in host mode */
 			clear_bit(B_SESS_VLD, &motg->inputs);
 			msm_otg_start_host(otg, 1);
 			msm_chg_enable_aca_det(motg);
 			msm_chg_disable_aca_intr(motg);
 			mod_timer(&motg->id_timer, ID_TIMER_FREQ);
 			if (msm_chg_check_aca_intr(motg))
 				work = 1;
 		}
 		break;
 	case OTG_STATE_A_WAIT_BCON:
 		if ((test_bit(ID, &motg->inputs) &&
 				!test_bit(ID_A, &motg->inputs)) ||
 				test_bit(A_BUS_DROP, &motg->inputs) ||
 				test_bit(A_WAIT_BCON, &motg->tmouts)) {
 			pr_debug("(id && id_a/b/c) || a_bus_drop ||"
 					"a_wait_bcon_tmout\n");
 			if (test_bit(A_WAIT_BCON, &motg->tmouts)) {
 				pr_info("Device No Response\n");
 				otg_send_event(OTG_EVENT_DEV_CONN_TMOUT);
 			}
 			msm_otg_del_timer(motg);
 			clear_bit(A_BUS_REQ, &motg->inputs);
 			clear_bit(B_CONN, &motg->inputs);
 			msm_otg_start_host(otg, 0);
 			/*
 			 * ACA: ID_A with NO accessory, just the A plug is
 			 * attached to ACA: Use IDCHG_MAX for charging
 			 */
 			if (test_bit(ID_A, &motg->inputs))
 				msm_otg_notify_charger(motg, IDEV_CHG_MIN);
 			else
 				msm_hsusb_vbus_power(motg, 0);
 			otg->phy->state = OTG_STATE_A_WAIT_VFALL;
 			msm_otg_start_timer(motg, TA_WAIT_VFALL, A_WAIT_VFALL);
 		} else if (!test_bit(A_VBUS_VLD, &motg->inputs)) {
 			pr_debug("!a_vbus_vld\n");
 			clear_bit(B_CONN, &motg->inputs);
 			msm_otg_del_timer(motg);
 			msm_otg_start_host(otg, 0);
 			otg->phy->state = OTG_STATE_A_VBUS_ERR;
 			msm_otg_reset(otg->phy);
 		} else if (test_bit(ID_A, &motg->inputs)) {
 			msm_hsusb_vbus_power(motg, 0);
 		} else if (!test_bit(A_BUS_REQ, &motg->inputs)) {
 			/*
 			 * If TA_WAIT_BCON is infinite, we don;t
 			 * turn off VBUS. Enter low power mode.
 			 */
 			if (TA_WAIT_BCON < 0)
 				pm_runtime_put_sync(otg->phy->dev);
 		} else if (!test_bit(ID, &motg->inputs)) {
 			msm_hsusb_vbus_power(motg, 1);
 		}
 		break;
 	case OTG_STATE_A_HOST:
 		if ((test_bit(ID, &motg->inputs) &&
 				!test_bit(ID_A, &motg->inputs)) ||
 				test_bit(A_BUS_DROP, &motg->inputs)) {
 			pr_debug("id_a/b/c || a_bus_drop\n");
 			clear_bit(B_CONN, &motg->inputs);
 			clear_bit(A_BUS_REQ, &motg->inputs);
 			msm_otg_del_timer(motg);
 			otg->phy->state = OTG_STATE_A_WAIT_VFALL;
 			msm_otg_start_host(otg, 0);
 			if (!test_bit(ID_A, &motg->inputs))
 				msm_hsusb_vbus_power(motg, 0);
 			msm_otg_start_timer(motg, TA_WAIT_VFALL, A_WAIT_VFALL);
 		} else if (!test_bit(A_VBUS_VLD, &motg->inputs)) {
 			pr_debug("!a_vbus_vld\n");
 			clear_bit(B_CONN, &motg->inputs);
 			msm_otg_del_timer(motg);
 			otg->phy->state = OTG_STATE_A_VBUS_ERR;
 			msm_otg_start_host(otg, 0);
 			msm_otg_reset(otg->phy);
 		} else if (!test_bit(A_BUS_REQ, &motg->inputs)) {
 			/*
 			 * a_bus_req is de-asserted when root hub is
 			 * suspended or HNP is in progress.
 			 */
 			pr_debug("!a_bus_req\n");
 			msm_otg_del_timer(motg);
 			otg->phy->state = OTG_STATE_A_SUSPEND;
 			if (otg->host->b_hnp_enable)
 				msm_otg_start_timer(motg, TA_AIDL_BDIS,
 						A_AIDL_BDIS);
 			else
 				pm_runtime_put_sync(otg->phy->dev);
 		} else if (!test_bit(B_CONN, &motg->inputs)) {
 			pr_debug("!b_conn\n");
 			msm_otg_del_timer(motg);
 			otg->phy->state = OTG_STATE_A_WAIT_BCON;
 			if (TA_WAIT_BCON > 0)
 				msm_otg_start_timer(motg, TA_WAIT_BCON,
 					A_WAIT_BCON);
 			if (msm_chg_check_aca_intr(motg))
 				work = 1;
 		} else if (test_bit(ID_A, &motg->inputs)) {
 			msm_otg_del_timer(motg);
 			msm_hsusb_vbus_power(motg, 0);
 			if (motg->chg_type == USB_ACA_DOCK_CHARGER)
 				msm_otg_notify_charger(motg,
 						IDEV_ACA_CHG_MAX);
 			else
 				msm_otg_notify_charger(motg,
 						IDEV_CHG_MIN - motg->mA_port);
 		} else if (!test_bit(ID, &motg->inputs)) {
 			motg->chg_state = USB_CHG_STATE_UNDEFINED;
 			motg->chg_type = USB_INVALID_CHARGER;
 			msm_otg_notify_charger(motg, 0);
 			msm_hsusb_vbus_power(motg, 1);
 		}
 		break;
 	case OTG_STATE_A_SUSPEND:
 		if ((test_bit(ID, &motg->inputs) &&
 				!test_bit(ID_A, &motg->inputs)) ||
 				test_bit(A_BUS_DROP, &motg->inputs) ||
 				test_bit(A_AIDL_BDIS, &motg->tmouts)) {
 			pr_debug("id_a/b/c || a_bus_drop ||"
 					"a_aidl_bdis_tmout\n");
 			msm_otg_del_timer(motg);
 			clear_bit(B_CONN, &motg->inputs);
 			otg->phy->state = OTG_STATE_A_WAIT_VFALL;
 			msm_otg_start_host(otg, 0);
 			msm_otg_reset(otg->phy);
 			if (!test_bit(ID_A, &motg->inputs))
 				msm_hsusb_vbus_power(motg, 0);
 			msm_otg_start_timer(motg, TA_WAIT_VFALL, A_WAIT_VFALL);
 		} else if (!test_bit(A_VBUS_VLD, &motg->inputs)) {
 			pr_debug("!a_vbus_vld\n");
 			msm_otg_del_timer(motg);
 			clear_bit(B_CONN, &motg->inputs);
 			otg->phy->state = OTG_STATE_A_VBUS_ERR;
 			msm_otg_start_host(otg, 0);
 			msm_otg_reset(otg->phy);
 		} else if (!test_bit(B_CONN, &motg->inputs) &&
 				otg->host->b_hnp_enable) {
 			pr_debug("!b_conn && b_hnp_enable");
 			otg->phy->state = OTG_STATE_A_PERIPHERAL;
 			msm_otg_host_hnp_enable(otg, 1);
 			otg->gadget->is_a_peripheral = 1;
 			msm_otg_start_peripheral(otg, 1);
 		} else if (!test_bit(B_CONN, &motg->inputs) &&
 				!otg->host->b_hnp_enable) {
 			pr_debug("!b_conn && !b_hnp_enable");
 			/*
 			 * bus request is dropped during suspend.
 			 * acquire again for next device.
 			 */
 			set_bit(A_BUS_REQ, &motg->inputs);
 			otg->phy->state = OTG_STATE_A_WAIT_BCON;
 			if (TA_WAIT_BCON > 0)
 				msm_otg_start_timer(motg, TA_WAIT_BCON,
 					A_WAIT_BCON);
 		} else if (test_bit(ID_A, &motg->inputs)) {
 			msm_hsusb_vbus_power(motg, 0);
 			msm_otg_notify_charger(motg,
 					IDEV_CHG_MIN - motg->mA_port);
 		} else if (!test_bit(ID, &motg->inputs)) {
 			msm_otg_notify_charger(motg, 0);
 			msm_hsusb_vbus_power(motg, 1);
 		}
 		break;
 	case OTG_STATE_A_PERIPHERAL:
 		if ((test_bit(ID, &motg->inputs) &&
 				!test_bit(ID_A, &motg->inputs)) ||
 				test_bit(A_BUS_DROP, &motg->inputs)) {
 			pr_debug("id _f/b/c || a_bus_drop\n");
 			/* Clear BIDL_ADIS timer */
 			msm_otg_del_timer(motg);
 			otg->phy->state = OTG_STATE_A_WAIT_VFALL;
 			msm_otg_start_peripheral(otg, 0);
 			otg->gadget->is_a_peripheral = 0;
 			msm_otg_start_host(otg, 0);
 			msm_otg_reset(otg->phy);
 			if (!test_bit(ID_A, &motg->inputs))
 				msm_hsusb_vbus_power(motg, 0);
 			msm_otg_start_timer(motg, TA_WAIT_VFALL, A_WAIT_VFALL);
 		} else if (!test_bit(A_VBUS_VLD, &motg->inputs)) {
 			pr_debug("!a_vbus_vld\n");
 			/* Clear BIDL_ADIS timer */
 			msm_otg_del_timer(motg);
 			otg->phy->state = OTG_STATE_A_VBUS_ERR;
 			msm_otg_start_peripheral(otg, 0);
 			otg->gadget->is_a_peripheral = 0;
 			msm_otg_start_host(otg, 0);
 		} else if (test_bit(A_BIDL_ADIS, &motg->tmouts)) {
 			pr_debug("a_bidl_adis_tmout\n");
 			msm_otg_start_peripheral(otg, 0);
 			otg->gadget->is_a_peripheral = 0;
 			otg->phy->state = OTG_STATE_A_WAIT_BCON;
 			set_bit(A_BUS_REQ, &motg->inputs);
 			msm_otg_host_hnp_enable(otg, 0);
 			if (TA_WAIT_BCON > 0)
 				msm_otg_start_timer(motg, TA_WAIT_BCON,
 					A_WAIT_BCON);
 		} else if (test_bit(ID_A, &motg->inputs)) {
 			msm_hsusb_vbus_power(motg, 0);
 			msm_otg_notify_charger(motg,
 					IDEV_CHG_MIN - motg->mA_port);
 		} else if (!test_bit(ID, &motg->inputs)) {
 			msm_otg_notify_charger(motg, 0);
 			msm_hsusb_vbus_power(motg, 1);
 		}
 		break;
 	case OTG_STATE_A_WAIT_VFALL:
 		if (test_bit(A_WAIT_VFALL, &motg->tmouts)) {
 			clear_bit(A_VBUS_VLD, &motg->inputs);
 			otg->phy->state = OTG_STATE_A_IDLE;
 			work = 1;
 		}
 		break;
 	case OTG_STATE_A_VBUS_ERR:
 		if ((test_bit(ID, &motg->inputs) &&
 				!test_bit(ID_A, &motg->inputs)) ||
 				test_bit(A_BUS_DROP, &motg->inputs) ||
 				test_bit(A_CLR_ERR, &motg->inputs)) {
 			otg->phy->state = OTG_STATE_A_WAIT_VFALL;
 			if (!test_bit(ID_A, &motg->inputs))
 				msm_hsusb_vbus_power(motg, 0);
 			msm_otg_start_timer(motg, TA_WAIT_VFALL, A_WAIT_VFALL);
 			motg->chg_state = USB_CHG_STATE_UNDEFINED;
 			motg->chg_type = USB_INVALID_CHARGER;
 			msm_otg_notify_charger(motg, 0);
 		}
 		break;
 	default:
 		break;
 	}
 	if (work)
 		queue_work(system_nrt_wq, &motg->sm_work);
 }

 static void msm_otg_suspend_work(struct work_struct *w)
 {
 	struct msm_otg *motg =
 		container_of(w, struct msm_otg, suspend_work.work);

 	/* This work is only for device bus suspend */
 	if (test_bit(A_BUS_SUSPEND, &motg->inputs))
 		msm_otg_sm_work(&motg->sm_work);
 }

 static irqreturn_t msm_otg_irq(int irq, void *data)
 {
 	struct msm_otg *motg = data;
 	struct usb_otg *otg = motg->phy.otg;
 	u32 otgsc = 0, usbsts, pc;
 	bool work = 0;
 	irqreturn_t ret = IRQ_HANDLED;

 	if (atomic_read(&motg->in_lpm)) {
 		pr_debug("OTG IRQ: %d in LPM\n", irq);
 		disable_irq_nosync(irq);
 		motg->async_int = irq;
 		if (!atomic_read(&motg->pm_suspended))
 			pm_request_resume(otg->phy->dev);
 		return IRQ_HANDLED;
 	}

 	usbsts = readl(USB_USBSTS);
 	otgsc = readl(USB_OTGSC);

 	if (!(otgsc & OTG_OTGSTS_MASK) && !(usbsts & OTG_USBSTS_MASK))
 		return IRQ_NONE;

 	if ((otgsc & OTGSC_IDIS) && (otgsc & OTGSC_IDIE)) {
 		if (otgsc & OTGSC_ID) {
 			dev_dbg(otg->phy->dev, "ID set\n");
 			set_bit(ID, &motg->inputs);
 		} else {
 			dev_dbg(otg->phy->dev, "ID clear\n");
 			/*
 			 * Assert a_bus_req to supply power on
 			 * VBUS when Micro/Mini-A cable is connected
 			 * with out user intervention.
 			 */
 			set_bit(A_BUS_REQ, &motg->inputs);
 			clear_bit(ID, &motg->inputs);
 			msm_chg_enable_aca_det(motg);
 		}
 		writel_relaxed(otgsc, USB_OTGSC);
 		work = 1;
 	} else if (otgsc & OTGSC_DPIS) {
 		pr_debug("DPIS detected\n");
 		writel_relaxed(otgsc, USB_OTGSC);
 		set_bit(A_SRP_DET, &motg->inputs);
 		set_bit(A_BUS_REQ, &motg->inputs);
 		work = 1;
 	} else if ((otgsc & OTGSC_BSVIE) && (otgsc & OTGSC_BSVIS)) {
 		writel_relaxed(otgsc, USB_OTGSC);
 		/*
 		 * BSV interrupt comes when operating as an A-device
 		 * (VBUS on/off).
 		 * But, handle BSV when charger is removed from ACA in ID_A
 		 */
 		if ((otg->phy->state >= OTG_STATE_A_IDLE) &&
 			!test_bit(ID_A, &motg->inputs))
 			return IRQ_HANDLED;
 		if (otgsc & OTGSC_BSV) {
 			dev_dbg(otg->phy->dev, "BSV set\n");
 			set_bit(B_SESS_VLD, &motg->inputs);
 		} else {
 			dev_dbg(otg->phy->dev, "BSV clear\n");
 			clear_bit(B_SESS_VLD, &motg->inputs);
 			clear_bit(A_BUS_SUSPEND, &motg->inputs);

 			msm_chg_check_aca_intr(motg);
 		}
 		work = 1;
 	} else if (usbsts & STS_PCI) {
 		pc = readl_relaxed(USB_PORTSC);
 		pr_debug("portsc = %x\n", pc);
 		ret = IRQ_NONE;
 		/*
 		 * HCD Acks PCI interrupt. We use this to switch
 		 * between different OTG states.
 		 */
 		work = 1;
 		switch (otg->phy->state) {
 		case OTG_STATE_A_SUSPEND:
 			if (otg->host->b_hnp_enable && (pc & PORTSC_CSC) &&
 					!(pc & PORTSC_CCS)) {
 				pr_debug("B_CONN clear\n");
 				clear_bit(B_CONN, &motg->inputs);
 				msm_otg_del_timer(motg);
 			}
 			break;
 		case OTG_STATE_A_PERIPHERAL:
 			/*
 			 * A-peripheral observed activity on bus.
 			 * clear A_BIDL_ADIS timer.
 			 */
 			msm_otg_del_timer(motg);
 			work = 0;
 			break;
 		case OTG_STATE_B_WAIT_ACON:
 			if ((pc & PORTSC_CSC) && (pc & PORTSC_CCS)) {
 				pr_debug("A_CONN set\n");
 				set_bit(A_CONN, &motg->inputs);
 				/* Clear ASE0_BRST timer */
 				msm_otg_del_timer(motg);
 			}
 			break;
 		case OTG_STATE_B_HOST:
 			if ((pc & PORTSC_CSC) && !(pc & PORTSC_CCS)) {
 				pr_debug("A_CONN clear\n");
 				clear_bit(A_CONN, &motg->inputs);
 				msm_otg_del_timer(motg);
 			}
 			break;
 		case OTG_STATE_A_WAIT_BCON:
 			if (TA_WAIT_BCON < 0)
 				set_bit(A_BUS_REQ, &motg->inputs);
 		default:
 			work = 0;
 			break;
 		}
 	} else if (usbsts & STS_URI) {
 		ret = IRQ_NONE;
 		switch (otg->phy->state) {
 		case OTG_STATE_A_PERIPHERAL:
 			/*
 			 * A-peripheral observed activity on bus.
 			 * clear A_BIDL_ADIS timer.
 			 */
 			msm_otg_del_timer(motg);
 			work = 0;
 			break;
 		default:
 			work = 0;
 			break;
 		}
 	} else if (usbsts & STS_SLI) {
 		ret = IRQ_NONE;
 		work = 0;
 		switch (otg->phy->state) {
 		case OTG_STATE_B_PERIPHERAL:
 			if (otg->gadget->b_hnp_enable) {
 				set_bit(A_BUS_SUSPEND, &motg->inputs);
 				set_bit(B_BUS_REQ, &motg->inputs);
 				work = 1;
 			}
 			break;
 		case OTG_STATE_A_PERIPHERAL:
 			msm_otg_start_timer(motg, TA_BIDL_ADIS,
 					A_BIDL_ADIS);
 			break;
 		default:
 			break;
 		}
 	} else if ((usbsts & PHY_ALT_INT)) {
 		writel_relaxed(PHY_ALT_INT, USB_USBSTS);
 		if (msm_chg_check_aca_intr(motg))
 			work = 1;
 		ret = IRQ_HANDLED;
 	}
 	if (work)
 		queue_work(system_nrt_wq, &motg->sm_work);

 	return ret;
 }

 static void msm_otg_set_vbus_state(int online)
 {
 	static bool init;
 	struct msm_otg *motg = the_msm_otg;

 	if (online) {
 		pr_debug("PMIC: BSV set\n");
 		set_bit(B_SESS_VLD, &motg->inputs);
 	} else {
 		pr_debug("PMIC: BSV clear\n");
 		clear_bit(B_SESS_VLD, &motg->inputs);
 	}

 	/* do not queue state m/c work if id is grounded */
 	if (!test_bit(ID, &motg->inputs)) {
 		/*
 		 * state machine work waits for initial VBUS
 		 * completion in UNDEFINED state.  Process
 		 * the initial VBUS event in ID_GND state.
 		 */
 		if (init)
 			return;
 	}

 	if (!init) {
 		init = true;
 		complete(&pmic_vbus_init);
 		pr_debug("PMIC: BSV init complete\n");
 		return;
 	}

 	if (test_bit(MHL, &motg->inputs) ||
 			mhl_det_in_progress) {
 		pr_debug("PMIC: BSV interrupt ignored in MHL\n");
 		return;
 	}

 	if (atomic_read(&motg->pm_suspended))
 		motg->sm_work_pending = true;
 	else
 		queue_work(system_nrt_wq, &motg->sm_work);
 }

 static void msm_pmic_id_status_w(struct work_struct *w)
 {
 	struct msm_otg *motg = container_of(w, struct msm_otg,
 						pmic_id_status_work.work);
 	int work = 0;

 	if (msm_otg_read_pmic_id_state(motg)) {
 		if (!test_and_set_bit(ID, &motg->inputs)) {
 			pr_debug("PMIC: ID set\n");
 			work = 1;
 		}
 	} else {
 		if (test_and_clear_bit(ID, &motg->inputs)) {
 			pr_debug("PMIC: ID clear\n");
 			set_bit(A_BUS_REQ, &motg->inputs);
 			work = 1;
 		}
 	}

 	if (work && (motg->phy.state != OTG_STATE_UNDEFINED)) {
 		if (atomic_read(&motg->pm_suspended))
 			motg->sm_work_pending = true;
 		else
 			queue_work(system_nrt_wq, &motg->sm_work);
 	}

 }

 #define MSM_PMIC_ID_STATUS_DELAY	5 /* 5msec */
 static irqreturn_t msm_pmic_id_irq(int irq, void *data)
 {
 	struct msm_otg *motg = data;

 	if (test_bit(MHL, &motg->inputs) ||
 			mhl_det_in_progress) {
 		pr_debug("PMIC: Id interrupt ignored in MHL\n");
 		return IRQ_HANDLED;
 	}

 	if (!aca_id_turned_on)
 		/*schedule delayed work for 5msec for ID line state to settle*/
 		queue_delayed_work(system_nrt_wq, &motg->pmic_id_status_work,
 				msecs_to_jiffies(MSM_PMIC_ID_STATUS_DELAY));

 	return IRQ_HANDLED;
 }

 static int msm_otg_mode_show(struct seq_file *s, void *unused)
 {
 	struct msm_otg *motg = s->private;
 	struct usb_otg *otg = motg->phy.otg;

 	switch (otg->phy->state) {
 	case OTG_STATE_A_HOST:
 		seq_printf(s, "host\n");
 		break;
 	case OTG_STATE_B_PERIPHERAL:
 		seq_printf(s, "peripheral\n");
 		break;
 	default:
 		seq_printf(s, "none\n");
 		break;
 	}

 	return 0;
 }

 static int msm_otg_mode_open(struct inode *inode, struct file *file)
 {
 	return single_open(file, msm_otg_mode_show, inode->i_private);
 }

 static ssize_t msm_otg_mode_write(struct file *file, const char __user *ubuf,
 				size_t count, loff_t *ppos)
 {
 	struct seq_file *s = file->private_data;
 	struct msm_otg *motg = s->private;
 	char buf[16];
 	struct usb_phy *phy = &motg->phy;
 	int status = count;
 	enum usb_mode_type req_mode;

 	memset(buf, 0x00, sizeof(buf));

 	if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count))) {
 		status = -EFAULT;
 		goto out;
 	}

 	if (!strncmp(buf, "host", 4)) {
 		req_mode = USB_HOST;
 	} else if (!strncmp(buf, "peripheral", 10)) {
 		req_mode = USB_PERIPHERAL;
 	} else if (!strncmp(buf, "none", 4)) {
 		req_mode = USB_NONE;
 	} else {
 		status = -EINVAL;
 		goto out;
 	}

 	switch (req_mode) {
 	case USB_NONE:
 		switch (phy->state) {
 		case OTG_STATE_A_HOST:
 		case OTG_STATE_B_PERIPHERAL:
 			set_bit(ID, &motg->inputs);
 			clear_bit(B_SESS_VLD, &motg->inputs);
 			break;
 		default:
 			goto out;
 		}
 		break;
 	case USB_PERIPHERAL:
 		switch (phy->state) {
 		case OTG_STATE_B_IDLE:
 		case OTG_STATE_A_HOST:
 			set_bit(ID, &motg->inputs);
 			set_bit(B_SESS_VLD, &motg->inputs);
 			break;
 		default:
 			goto out;
 		}
 		break;
 	case USB_HOST:
 		switch (phy->state) {
 		case OTG_STATE_B_IDLE:
 		case OTG_STATE_B_PERIPHERAL:
 			clear_bit(ID, &motg->inputs);
 			break;
 		default:
 			goto out;
 		}
 		break;
 	default:
 		goto out;
 	}

 	pm_runtime_resume(phy->dev);
 	queue_work(system_nrt_wq, &motg->sm_work);
 out:
 	return status;
 }

 const struct file_operations msm_otg_mode_fops = {
 	.open = msm_otg_mode_open,
 	.read = seq_read,
 	.write = msm_otg_mode_write,
 	.llseek = seq_lseek,
 	.release = single_release,
 };

 static int msm_otg_show_otg_state(struct seq_file *s, void *unused)
 {
 	struct msm_otg *motg = s->private;
 	struct usb_phy *phy = &motg->phy;

 	seq_printf(s, "%s\n", otg_state_string(phy->state));
 	return 0;
 }

 static int msm_otg_otg_state_open(struct inode *inode, struct file *file)
 {
 	return single_open(file, msm_otg_show_otg_state, inode->i_private);
 }

 const struct file_operations msm_otg_state_fops = {
 	.open = msm_otg_otg_state_open,
 	.read = seq_read,
 	.llseek = seq_lseek,
 	.release = single_release,
 };

 static int msm_otg_show_chg_type(struct seq_file *s, void *unused)
 {
 	struct msm_otg *motg = s->private;

 	seq_printf(s, "%s\n", chg_to_string(motg->chg_type));
 	return 0;
 }

 static int msm_otg_chg_open(struct inode *inode, struct file *file)
 {
 	return single_open(file, msm_otg_show_chg_type, inode->i_private);
 }

 const struct file_operations msm_otg_chg_fops = {
 	.open = msm_otg_chg_open,
 	.read = seq_read,
 	.llseek = seq_lseek,
 	.release = single_release,
 };

 static int msm_otg_aca_show(struct seq_file *s, void *unused)
 {
 	if (debug_aca_enabled)
 		seq_printf(s, "enabled\n");
 	else
 		seq_printf(s, "disabled\n");

 	return 0;
 }

 static int msm_otg_aca_open(struct inode *inode, struct file *file)
 {
 	return single_open(file, msm_otg_aca_show, inode->i_private);
 }

 static ssize_t msm_otg_aca_write(struct file *file, const char __user *ubuf,
 				size_t count, loff_t *ppos)
 {
 	char buf[8];

 	memset(buf, 0x00, sizeof(buf));

 	if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
 		return -EFAULT;

 	if (!strncmp(buf, "enable", 6))
 		debug_aca_enabled = true;
 	else
 		debug_aca_enabled = false;

 	return count;
 }

 const struct file_operations msm_otg_aca_fops = {
 	.open = msm_otg_aca_open,
 	.read = seq_read,
 	.write = msm_otg_aca_write,
 	.llseek = seq_lseek,
 	.release = single_release,
 };

 static int msm_otg_bus_show(struct seq_file *s, void *unused)
 {
 	if (debug_bus_voting_enabled)
 		seq_printf(s, "enabled\n");
 	else
 		seq_printf(s, "disabled\n");

 	return 0;
 }

 static int msm_otg_bus_open(struct inode *inode, struct file *file)
 {
 	return single_open(file, msm_otg_bus_show, inode->i_private);
 }

 static ssize_t msm_otg_bus_write(struct file *file, const char __user *ubuf,
 				size_t count, loff_t *ppos)
 {
 	char buf[8];
 	struct seq_file *s = file->private_data;
 	struct msm_otg *motg = s->private;

 	memset(buf, 0x00, sizeof(buf));

 	if (copy_from_user(&buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
 		return -EFAULT;

 	if (!strncmp(buf, "enable", 6)) {
 		/* Do not vote here. Let OTG statemachine decide when to vote */
 		debug_bus_voting_enabled = true;
 	} else {
 		debug_bus_voting_enabled = false;
 		msm_otg_bus_vote(motg, USB_MIN_PERF_VOTE);
 	}

 	return count;
 }

 static int otg_power_get_property_usb(struct power_supply *psy,
 				  enum power_supply_property psp,
 				  union power_supply_propval *val)
 {
 	struct msm_otg *motg = container_of(psy, struct msm_otg, usb_psy);
 	switch (psp) {
 	case POWER_SUPPLY_PROP_SCOPE:
 		if (motg->host_mode)
 			val->intval = POWER_SUPPLY_SCOPE_SYSTEM;
 		else
 			val->intval = POWER_SUPPLY_SCOPE_DEVICE;
 		break;
 	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
 		val->intval = motg->voltage_max;
 		break;
 	case POWER_SUPPLY_PROP_CURRENT_MAX:
 		val->intval = motg->current_max;
 		break;
 	/* Reflect USB enumeration */
 	case POWER_SUPPLY_PROP_PRESENT:
 	case POWER_SUPPLY_PROP_ONLINE:
 		val->intval = motg->online;
 		break;
 	case POWER_SUPPLY_PROP_TYPE:
 		val->intval = psy->type;
 		break;
 	case POWER_SUPPLY_PROP_HEALTH:
 		val->intval = motg->usbin_health;
 		break;
 	default:
 		return -EINVAL;
 	}
 	return 0;
 }

 static int otg_power_set_property_usb(struct power_supply *psy,
 				  enum power_supply_property psp,
 				  const union power_supply_propval *val)
 {
 	struct msm_otg *motg = container_of(psy, struct msm_otg, usb_psy);

 	switch (psp) {
 	/* Process PMIC notification in PRESENT prop */
 	case POWER_SUPPLY_PROP_PRESENT:
 		msm_otg_set_vbus_state(val->intval);
 		break;
 	/* The ONLINE property reflects if usb has enumerated */
 	case POWER_SUPPLY_PROP_ONLINE:
 		motg->online = val->intval;
 		break;
 	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
 		motg->voltage_max = val->intval;
 		break;
 	case POWER_SUPPLY_PROP_CURRENT_MAX:
 		motg->current_max = val->intval;
 		break;
 	case POWER_SUPPLY_PROP_TYPE:
 		psy->type = val->intval;
 		break;
 	case POWER_SUPPLY_PROP_HEALTH:
 		motg->usbin_health = val->intval;
 		break;
 	default:
 		return -EINVAL;
 	}

 	power_supply_changed(&motg->usb_psy);
 	return 0;
 }

 static int otg_power_property_is_writeable_usb(struct power_supply *psy,
 						enum power_supply_property psp)
 {
 	switch (psp) {
 	case POWER_SUPPLY_PROP_HEALTH:
 	case POWER_SUPPLY_PROP_PRESENT:
 	case POWER_SUPPLY_PROP_ONLINE:
 	case POWER_SUPPLY_PROP_VOLTAGE_MAX:
 	case POWER_SUPPLY_PROP_CURRENT_MAX:
 		return 1;
 	default:
 		break;
 	}

 	return 0;
 }

 static char *otg_pm_power_supplied_to[] = {
 	"battery",
 };

 static enum power_supply_property otg_pm_power_props_usb[] = {
 	POWER_SUPPLY_PROP_HEALTH,
 	POWER_SUPPLY_PROP_PRESENT,
 	POWER_SUPPLY_PROP_ONLINE,
 	POWER_SUPPLY_PROP_VOLTAGE_MAX,
 	POWER_SUPPLY_PROP_CURRENT_MAX,
 	POWER_SUPPLY_PROP_SCOPE,
 	POWER_SUPPLY_PROP_TYPE,
 };

 const struct file_operations msm_otg_bus_fops = {
 	.open = msm_otg_bus_open,
 	.read = seq_read,
 	.write = msm_otg_bus_write,
 	.llseek = seq_lseek,
 	.release = single_release,
 };

 static struct dentry *msm_otg_dbg_root;

 static int msm_otg_debugfs_init(struct msm_otg *motg)
 {
 	struct dentry *msm_otg_dentry;

 	msm_otg_dbg_root = debugfs_create_dir("msm_otg", NULL);

 	if (!msm_otg_dbg_root || IS_ERR(msm_otg_dbg_root))
 		return -ENODEV;

 	if (motg->pdata->mode == USB_OTG &&
 		motg->pdata->otg_control == OTG_USER_CONTROL) {

 		msm_otg_dentry = debugfs_create_file("mode", S_IRUGO |
 			S_IWUSR, msm_otg_dbg_root, motg,
 			&msm_otg_mode_fops);

 		if (!msm_otg_dentry) {
 			debugfs_remove(msm_otg_dbg_root);
 			msm_otg_dbg_root = NULL;
 			return -ENODEV;
 		}
 	}

 	msm_otg_dentry = debugfs_create_file("chg_type", S_IRUGO,
 		msm_otg_dbg_root, motg,
 		&msm_otg_chg_fops);

 	if (!msm_otg_dentry) {
 		debugfs_remove_recursive(msm_otg_dbg_root);
 		return -ENODEV;
 	}

 	msm_otg_dentry = debugfs_create_file("aca", S_IRUGO | S_IWUSR,
 		msm_otg_dbg_root, motg,
 		&msm_otg_aca_fops);

 	if (!msm_otg_dentry) {
 		debugfs_remove_recursive(msm_otg_dbg_root);
 		return -ENODEV;
 	}

 	msm_otg_dentry = debugfs_create_file("bus_voting", S_IRUGO | S_IWUSR,
 		msm_otg_dbg_root, motg,
 		&msm_otg_bus_fops);

 	if (!msm_otg_dentry) {
 		debugfs_remove_recursive(msm_otg_dbg_root);
 		return -ENODEV;
 	}

 	msm_otg_dentry = debugfs_create_file("otg_state", S_IRUGO,
 				msm_otg_dbg_root, motg, &msm_otg_state_fops);

 	if (!msm_otg_dentry) {
 		debugfs_remove_recursive(msm_otg_dbg_root);
 		return -ENODEV;
 	}
 	return 0;
 }

 static void msm_otg_debugfs_cleanup(void)
 {
 	debugfs_remove_recursive(msm_otg_dbg_root);
 }

 #define MSM_OTG_CMD_ID		0x09
 #define MSM_OTG_DEVICE_ID	0x04
 #define MSM_OTG_VMID_IDX	0xFF
 #define MSM_OTG_MEM_TYPE	0x02
 struct msm_otg_scm_cmd_buf {
 	unsigned int device_id;
 	unsigned int vmid_idx;
 	unsigned int mem_type;
 } __attribute__ ((__packed__));

 static void msm_otg_pnoc_errata_fix(struct msm_otg *motg)
 {
 	int ret;
 	struct msm_otg_platform_data *pdata = motg->pdata;
 	struct msm_otg_scm_cmd_buf cmd_buf;

 	if (!pdata->pnoc_errata_fix)
 		return;

 	dev_dbg(motg->phy.dev, "applying fix for pnoc h/w issue\n");

 	cmd_buf.device_id = MSM_OTG_DEVICE_ID;
 	cmd_buf.vmid_idx = MSM_OTG_VMID_IDX;
 	cmd_buf.mem_type = MSM_OTG_MEM_TYPE;

 	ret = scm_call(SCM_SVC_MP, MSM_OTG_CMD_ID, &cmd_buf,
 				sizeof(cmd_buf), NULL, 0);

 	if (ret)
 		dev_err(motg->phy.dev, "scm command failed to update VMIDMT\n");
 }

 static u64 msm_otg_dma_mask = DMA_BIT_MASK(64);
 static struct platform_device *msm_otg_add_pdev(
 		struct platform_device *ofdev, const char *name)
 {
 	struct platform_device *pdev;
 	const struct resource *res = ofdev->resource;
 	unsigned int num = ofdev->num_resources;
 	int retval;
 	struct ci13xxx_platform_data ci_pdata;
 	struct msm_otg_platform_data *otg_pdata;

 	pdev = platform_device_alloc(name, -1);
 	if (!pdev) {
 		retval = -ENOMEM;
 		goto error;
 	}

 	pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
 	pdev->dev.dma_mask = &msm_otg_dma_mask;

 	if (num) {
 		retval = platform_device_add_resources(pdev, res, num);
 		if (retval)
 			goto error;
 	}

 	if (!strcmp(name, "msm_hsusb")) {
 		otg_pdata =
 			(struct msm_otg_platform_data *)
 				ofdev->dev.platform_data;
 		ci_pdata.log2_itc = otg_pdata->log2_itc;
 		ci_pdata.usb_core_id = 0;
 		ci_pdata.l1_supported = otg_pdata->l1_supported;
 		ci_pdata.enable_ahb2ahb_bypass =
 				otg_pdata->enable_ahb2ahb_bypass;
 		retval = platform_device_add_data(pdev, &ci_pdata,
 			sizeof(ci_pdata));
 		if (retval)
 			goto error;
 	}

 	retval = platform_device_add(pdev);
 	if (retval)
 		goto error;

 	return pdev;

 error:
 	platform_device_put(pdev);
 	return ERR_PTR(retval);
 }

 static int msm_otg_setup_devices(struct platform_device *ofdev,
 		enum usb_mode_type mode, bool init)
 {
 	const char *gadget_name = "msm_hsusb";
 	const char *host_name = "msm_hsusb_host";
 	static struct platform_device *gadget_pdev;
 	static struct platform_device *host_pdev;
 	int retval = 0;

 	if (!init) {
 		if (gadget_pdev)
 			platform_device_unregister(gadget_pdev);
 		if (host_pdev)
 			platform_device_unregister(host_pdev);
 		return 0;
 	}

 	switch (mode) {
 	case USB_OTG:
 		/* fall through */
 	case USB_PERIPHERAL:
 		gadget_pdev = msm_otg_add_pdev(ofdev, gadget_name);
 		if (IS_ERR(gadget_pdev)) {
 			retval = PTR_ERR(gadget_pdev);
 			break;
 		}
 		if (mode == USB_PERIPHERAL)
 			break;
 		/* fall through */
 	case USB_HOST:
 		host_pdev = msm_otg_add_pdev(ofdev, host_name);
 		if (IS_ERR(host_pdev)) {
 			retval = PTR_ERR(host_pdev);
 			if (mode == USB_OTG)
 				platform_device_unregister(gadget_pdev);
 		}
 		break;
 	default:
 		break;
 	}

 	return retval;
 }

 static int msm_otg_register_power_supply(struct platform_device *pdev,
 					struct msm_otg *motg)
 {
 	int ret;

 	ret = power_supply_register(&pdev->dev, &motg->usb_psy);
 	if (ret < 0) {
 		dev_err(motg->phy.dev,
 			"%s:power_supply_register usb failed\n",
 			__func__);
 		return ret;
 	}

 	legacy_power_supply = false;
 	return 0;
 }

 static int msm_otg_ext_chg_open(struct inode *inode, struct file *file)
 {
 	struct msm_otg *motg = the_msm_otg;

 	pr_debug("msm_otg ext chg open\n");

 	motg->ext_chg_opened = true;
 	file->private_data = (void *)motg;
 	return 0;
 }

 static long
 msm_otg_ext_chg_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 {
 	struct msm_otg *motg = file->private_data;
 	struct msm_usb_chg_info info = {0};
 	int ret = 0, val;

 	switch (cmd) {
 	case MSM_USB_EXT_CHG_INFO:
 		info.chg_block_type = USB_CHG_BLOCK_ULPI;
 		info.page_offset = motg->io_res->start & ~PAGE_MASK;
 		/* mmap() works on PAGE granularity */
 		info.length = PAGE_SIZE;

 		if (copy_to_user((void __user *)arg, &info, sizeof(info))) {
 			pr_err("%s: copy to user failed\n\n", __func__);
 			ret = -EFAULT;
 		}
 		break;
 	case MSM_USB_EXT_CHG_BLOCK_LPM:
 		if (get_user(val, (int __user *)arg)) {
 			pr_err("%s: get_user failed\n\n", __func__);
 			ret = -EFAULT;
 			break;
 		}
 		pr_debug("%s: LPM block request %d\n", __func__, val);
 		if (val) { /* block LPM */
 			if (motg->chg_type == USB_DCP_CHARGER) {
 				/*
 				 * If device is already suspended, resume it.
 				 * The PM usage counter is incremented in
 				 * runtime resume method.  if device is not
 				 * suspended, cancel the scheduled suspend
 				 * and increment the PM usage counter.
 				 */
 				if (pm_runtime_suspended(motg->phy.dev))
 					pm_runtime_resume(motg->phy.dev);
 				else
 					pm_runtime_get_sync(motg->phy.dev);
 			} else {
 				motg->ext_chg_active = false;
 				complete(&motg->ext_chg_wait);
 				ret = -ENODEV;
 			}
 		} else {
 			motg->ext_chg_active = false;
 			complete(&motg->ext_chg_wait);
 			pm_runtime_put(motg->phy.dev);
 		}
 		break;
 	default:
 		ret = -EINVAL;
 	}

 	return ret;
 }

 static int msm_otg_ext_chg_mmap(struct file *file, struct vm_area_struct *vma)
 {
 	struct msm_otg *motg = file->private_data;
 	unsigned long vsize = vma->vm_end - vma->vm_start;
 	int ret;

 	if (vma->vm_pgoff || vsize > PAGE_SIZE)
 		return -EINVAL;

 	vma->vm_pgoff = __phys_to_pfn(motg->io_res->start);
 	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);

 	ret = io_remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff,
 				 vsize, vma->vm_page_prot);
 	if (ret < 0) {
 		pr_err("%s: failed with return val %d\n", __func__, ret);
 		return ret;
 	}

 	return 0;
 }

 static int msm_otg_ext_chg_release(struct inode *inode, struct file *file)
 {
 	struct msm_otg *motg = file->private_data;

 	pr_debug("msm_otg ext chg release\n");

 	motg->ext_chg_opened = false;

 	return 0;
 }

 static const struct file_operations msm_otg_ext_chg_fops = {
 	.owner = THIS_MODULE,
 	.open = msm_otg_ext_chg_open,
 	.unlocked_ioctl = msm_otg_ext_chg_ioctl,
 	.mmap = msm_otg_ext_chg_mmap,
 	.release = msm_otg_ext_chg_release,
 };

 static int msm_otg_setup_ext_chg_cdev(struct msm_otg *motg)
 {
 	int ret;

 	if (motg->pdata->enable_sec_phy || motg->pdata->mode == USB_HOST ||
 			motg->pdata->otg_control != OTG_PMIC_CONTROL ||
 			psy != &motg->usb_psy) {
 		pr_debug("usb ext chg is not supported by msm otg\n");
 		return -ENODEV;
 	}

 	ret = alloc_chrdev_region(&motg->ext_chg_dev, 0, 1, "usb_ext_chg");
 	if (ret < 0) {
 		pr_err("Fail to allocate usb ext char dev region\n");
 		return ret;
 	}
 	motg->ext_chg_class = class_create(THIS_MODULE, "msm_ext_chg");
 	if (ret < 0) {
 		pr_err("Fail to create usb ext chg class\n");
 		goto unreg_chrdev;
 	}
 	cdev_init(&motg->ext_chg_cdev, &msm_otg_ext_chg_fops);
 	motg->ext_chg_cdev.owner = THIS_MODULE;

 	ret = cdev_add(&motg->ext_chg_cdev, motg->ext_chg_dev, 1);
 	if (ret < 0) {
 		pr_err("Fail to add usb ext chg cdev\n");
 		goto destroy_class;
 	}
 	motg->ext_chg_device = device_create(motg->ext_chg_class,
 					NULL, motg->ext_chg_dev, NULL,
 					"usb_ext_chg");
 	if (IS_ERR(motg->ext_chg_device)) {
 		pr_err("Fail to create usb ext chg device\n");
 		ret = PTR_ERR(motg->ext_chg_device);
 		motg->ext_chg_device = NULL;
 		goto del_cdev;
 	}

 	init_completion(&motg->ext_chg_wait);
 	pr_debug("msm otg ext chg cdev setup success\n");
 	return 0;

 del_cdev:
 	cdev_del(&motg->ext_chg_cdev);
 destroy_class:
 	class_destroy(motg->ext_chg_class);
 unreg_chrdev:
 	unregister_chrdev_region(motg->ext_chg_dev, 1);

 	return ret;
 }

 static ssize_t dpdm_pulldown_enable_show(struct device *dev,
 			       struct device_attribute *attr, char *buf)
 {
 	struct msm_otg *motg = the_msm_otg;
 	struct msm_otg_platform_data *pdata = motg->pdata;

 	return snprintf(buf, PAGE_SIZE, "%s\n", pdata->dpdm_pulldown_added ?
 							"enabled" : "disabled");
 }

 static ssize_t dpdm_pulldown_enable_store(struct device *dev,
 		struct device_attribute *attr, const char
 		*buf, size_t size)
 {
 	struct msm_otg *motg = the_msm_otg;
 	struct msm_otg_platform_data *pdata = motg->pdata;

 	if (!strnicmp(buf, "enable", 6)) {
 		pdata->dpdm_pulldown_added = true;
 		return size;
 	} else if (!strnicmp(buf, "disable", 7)) {
 		pdata->dpdm_pulldown_added = false;
 		return size;
 	}

 	return -EINVAL;
 }

 static DEVICE_ATTR(dpdm_pulldown_enable, S_IRUGO | S_IWUSR,
 		dpdm_pulldown_enable_show, dpdm_pulldown_enable_store);

 struct msm_otg_platform_data *msm_otg_dt_to_pdata(struct platform_device *pdev)
 {
 	struct device_node *node = pdev->dev.of_node;
 	struct msm_otg_platform_data *pdata;
 	int len = 0;

 	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
 	if (!pdata) {
 		pr_err("unable to allocate platform data\n");
 		return NULL;
 	}
 	of_get_property(node, "qcom,hsusb-otg-phy-init-seq", &len);
 	if (len) {
 		pdata->phy_init_seq = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
 		if (!pdata->phy_init_seq)
 			return NULL;
 		of_property_read_u32_array(node, "qcom,hsusb-otg-phy-init-seq",
 				pdata->phy_init_seq,
 				len/sizeof(*pdata->phy_init_seq));
 	}
 	of_property_read_u32(node, "qcom,hsusb-otg-power-budget",
 				&pdata->power_budget);
 	of_property_read_u32(node, "qcom,hsusb-otg-mode",
 				&pdata->mode);
 	of_property_read_u32(node, "qcom,hsusb-otg-otg-control",
 				&pdata->otg_control);
 	of_property_read_u32(node, "qcom,hsusb-otg-default-mode",
 				&pdata->default_mode);
 	of_property_read_u32(node, "qcom,hsusb-otg-phy-type",
 				&pdata->phy_type);
 	pdata->disable_reset_on_disconnect = of_property_read_bool(node,
 				"qcom,hsusb-otg-disable-reset");
 	pdata->pnoc_errata_fix = of_property_read_bool(node,
 				"qcom,hsusb-otg-pnoc-errata-fix");
 	pdata->enable_lpm_on_dev_suspend = of_property_read_bool(node,
 				"qcom,hsusb-otg-lpm-on-dev-suspend");
 	pdata->core_clk_always_on_workaround = of_property_read_bool(node,
 				"qcom,hsusb-otg-clk-always-on-workaround");
 	pdata->delay_lpm_on_disconnect = of_property_read_bool(node,
 				"qcom,hsusb-otg-delay-lpm");
 	pdata->delay_lpm_hndshk_on_disconnect = of_property_read_bool(node,
 				"qcom,hsusb-otg-delay-lpm-hndshk-on-disconnect");
 	pdata->dp_manual_pullup = of_property_read_bool(node,
 				"qcom,dp-manual-pullup");
 	pdata->enable_sec_phy = of_property_read_bool(node,
 					"qcom,usb2-enable-hsphy2");
 	of_property_read_u32(node, "qcom,hsusb-log2-itc",
 				&pdata->log2_itc);

 	of_property_read_u32(node, "qcom,hsusb-otg-mpm-dpsehv-int",
 				&pdata->mpm_dpshv_int);
 	of_property_read_u32(node, "qcom,hsusb-otg-mpm-dmsehv-int",
 				&pdata->mpm_dmshv_int);
 	pdata->pmic_id_irq = platform_get_irq_byname(pdev, "pmic_id_irq");
 	if (pdata->pmic_id_irq < 0)
 		pdata->pmic_id_irq = 0;

 	pdata->l1_supported = of_property_read_bool(node,
 				"qcom,hsusb-l1-supported");
 	pdata->enable_ahb2ahb_bypass = of_property_read_bool(node,
 				"qcom,ahb-async-bridge-bypass");
 	pdata->disable_retention_with_vdd_min = of_property_read_bool(node,
 				"qcom,disable-retention-with-vdd-min");

 	return pdata;
 }

 static int __init msm_otg_probe(struct platform_device *pdev)
 {
 	int ret = 0;
 	int len = 0;
 	u32 tmp[3];
 	struct resource *res;
 	struct msm_otg *motg;
 	struct usb_phy *phy;
 	struct msm_otg_platform_data *pdata;

 	dev_info(&pdev->dev, "msm_otg probe\n");

 	if (pdev->dev.of_node) {
 		dev_dbg(&pdev->dev, "device tree enabled\n");
 		pdata = msm_otg_dt_to_pdata(pdev);
 		if (!pdata)
 			return -ENOMEM;

 		pdata->bus_scale_table = msm_bus_cl_get_pdata(pdev);
 		if (!pdata->bus_scale_table)
 			dev_dbg(&pdev->dev, "bus scaling is disabled\n");

 		pdev->dev.platform_data = pdata;
 		ret = msm_otg_setup_devices(pdev, pdata->mode, true);
 		if (ret) {
 			dev_err(&pdev->dev, "devices setup failed\n");
 			return ret;
 		}
 	} else if (!pdev->dev.platform_data) {
 		dev_err(&pdev->dev, "No platform data given. Bailing out\n");
 		return -ENODEV;
 	} else {
 		pdata = pdev->dev.platform_data;
 	}

 	motg = devm_kzalloc(&pdev->dev, sizeof(struct msm_otg), GFP_KERNEL);
 	if (!motg) {
 		dev_err(&pdev->dev, "unable to allocate msm_otg\n");
 		return -ENOMEM;
 	}

 	motg->phy.otg = devm_kzalloc(&pdev->dev, sizeof(struct usb_otg),
 							GFP_KERNEL);
 	if (!motg->phy.otg) {
 		dev_err(&pdev->dev, "unable to allocate usb_otg\n");
 		return -ENOMEM;
 	}

 	the_msm_otg = motg;
 	motg->pdata = pdata;
 	phy = &motg->phy;
 	phy->dev = &pdev->dev;

 	if (motg->pdata->bus_scale_table) {
 		motg->bus_perf_client =
 		    msm_bus_scale_register_client(motg->pdata->bus_scale_table);
 		if (!motg->bus_perf_client) {
 			dev_err(motg->phy.dev, "%s: Failed to register BUS\n"
 						"scaling client!!\n", __func__);
 		} else {
 			debug_bus_voting_enabled = true;
 			/* Some platforms require BUS vote to control clocks */
 			msm_otg_bus_vote(motg, USB_MIN_PERF_VOTE);
 		}
 	}

 	/*
 	 * ACA ID_GND threshold range is overlapped with OTG ID_FLOAT.  Hence
 	 * PHY treat ACA ID_GND as float and no interrupt is generated.  But
 	 * PMIC can detect ACA ID_GND and generate an interrupt.
 	 */
 	if (aca_enabled() && motg->pdata->otg_control != OTG_PMIC_CONTROL) {
 		dev_err(&pdev->dev, "ACA can not be enabled without PMIC\n");
 		ret = -EINVAL;
 		goto devote_bus_bw;
 	}

 	/* initialize reset counter */
 	motg->reset_counter = 0;

 	/*
 	 * Targets on which link uses asynchronous reset methodology,
 	 * free running clock is not required during the reset.
 	 */
 	motg->clk = clk_get(&pdev->dev, "alt_core_clk");
 	if (IS_ERR(motg->clk))
 		dev_dbg(&pdev->dev, "alt_core_clk is not present\n");
 	else
 		clk_set_rate(motg->clk, 60000000);

 	/*
 	 * USB Core is running its protocol engine based on CORE CLK,
 	 * CORE CLK  must be running at >55Mhz for correct HSUSB
 	 * operation and USB core cannot tolerate frequency changes on
 	 * CORE CLK. For such USB cores, vote for maximum clk frequency
 	 * on pclk source
 	 */
 	motg->core_clk = clk_get(&pdev->dev, "core_clk");
 	if (IS_ERR(motg->core_clk)) {
 		motg->core_clk = NULL;
 		dev_err(&pdev->dev, "failed to get core_clk\n");
 		ret = PTR_ERR(motg->core_clk);
 		goto put_clk;
 	}

 	/*
 	 * Get Max supported clk frequency for USB Core CLK and request
 	 * to set the same.
 	 */
 	motg->core_clk_rate = clk_round_rate(motg->core_clk, LONG_MAX);
 	if (IS_ERR_VALUE(motg->core_clk_rate)) {
 		dev_err(&pdev->dev, "fail to get core clk max freq.\n");
 	} else {
 		ret = clk_set_rate(motg->core_clk, motg->core_clk_rate);
 		if (ret)
 			dev_err(&pdev->dev, "fail to set core_clk freq:%d\n",
 									ret);
 	}

 	motg->pclk = clk_get(&pdev->dev, "iface_clk");
 	if (IS_ERR(motg->pclk)) {
 		dev_err(&pdev->dev, "failed to get iface_clk\n");
 		ret = PTR_ERR(motg->pclk);
 		goto put_core_clk;
 	}

 	/*
 	 * On few platforms USB PHY is fed with sleep clk.
 	 * Hence don't fail probe.
 	 */
 	motg->sleep_clk = devm_clk_get(&pdev->dev, "sleep_clk");
 	if (IS_ERR(motg->sleep_clk)) {
 		dev_dbg(&pdev->dev, "failed to get sleep_clk\n");
 	} else {
 		ret = clk_prepare_enable(motg->sleep_clk);
 		if (ret) {
 			dev_err(&pdev->dev, "%s failed to vote sleep_clk%d\n",
 							__func__, ret);
 			goto put_pclk;
 		}
 	}

 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
 		dev_err(&pdev->dev, "failed to get platform resource mem\n");
 		ret = -ENODEV;
 		goto disable_sleep_clk;
 	}

 	motg->io_res = res;
 	motg->regs = ioremap(res->start, resource_size(res));
 	if (!motg->regs) {
 		dev_err(&pdev->dev, "ioremap failed\n");
 		ret = -ENOMEM;
 		goto disable_sleep_clk;
 	}
 	dev_info(&pdev->dev, "OTG regs = %p\n", motg->regs);

 	motg->irq = platform_get_irq(pdev, 0);
 	if (!motg->irq) {
 		dev_err(&pdev->dev, "platform_get_irq failed\n");
 		ret = -ENODEV;
 		goto free_regs;
 	}

 	motg->async_irq = platform_get_irq_byname(pdev, "async_irq");
 	if (motg->async_irq < 0) {
 		dev_dbg(&pdev->dev, "platform_get_irq for async_int failed\n");
 		motg->async_irq = 0;
 	}

 	motg->xo_clk = clk_get(&pdev->dev, "xo");
 	if (IS_ERR(motg->xo_clk)) {
 		motg->xo_handle = msm_xo_get(MSM_XO_TCXO_D0, "usb");
 		if (IS_ERR(motg->xo_handle)) {
 			dev_err(&pdev->dev, "%s fail to get handle for TCXO\n",
 								__func__);
 			ret = PTR_ERR(motg->xo_handle);
 			goto free_regs;
 		} else {
 			ret = msm_xo_mode_vote(motg->xo_handle, MSM_XO_MODE_ON);
 			if (ret) {
 				dev_err(&pdev->dev, "%s XO voting failed %d\n",
 								__func__, ret);
 				goto free_xo_handle;
 			}
 		}
 	} else {
 		ret = clk_prepare_enable(motg->xo_clk);
 		if (ret) {
 			dev_err(&pdev->dev, "%s failed to vote for TCXO %d\n",
 							__func__, ret);
 			goto free_xo_handle;
 		}
 	}


 	clk_prepare_enable(motg->pclk);

 	motg->vdd_type = VDDCX_CORNER;
 	hsusb_vdd = devm_regulator_get(motg->phy.dev, "hsusb_vdd_dig");
 	if (IS_ERR(hsusb_vdd)) {
 		hsusb_vdd = devm_regulator_get(motg->phy.dev, "HSUSB_VDDCX");
 		if (IS_ERR(hsusb_vdd)) {
 			dev_err(motg->phy.dev, "unable to get hsusb vddcx\n");
 			ret = PTR_ERR(hsusb_vdd);
 			goto devote_xo_handle;
 		}
 		motg->vdd_type = VDDCX;
 	}

 	if (pdev->dev.of_node) {
 		of_get_property(pdev->dev.of_node,
 				"qcom,vdd-voltage-level",
 				&len);
 		if (len == sizeof(tmp)) {
 			of_property_read_u32_array(pdev->dev.of_node,
 					"qcom,vdd-voltage-level",
 					tmp, len/sizeof(*tmp));
 			vdd_val[motg->vdd_type][0] = tmp[0];
 			vdd_val[motg->vdd_type][1] = tmp[1];
 			vdd_val[motg->vdd_type][2] = tmp[2];
 		} else {
 			dev_dbg(&pdev->dev, "Using default hsusb vdd config.\n");
 		}
 	}

 	ret = msm_hsusb_config_vddcx(1);
 	if (ret) {
 		dev_err(&pdev->dev, "hsusb vddcx configuration failed\n");
 		goto devote_xo_handle;
 	}

 	ret = regulator_enable(hsusb_vdd);
 	if (ret) {
 		dev_err(&pdev->dev, "unable to enable the hsusb vddcx\n");
 		goto free_config_vddcx;
 	}

 	ret = msm_hsusb_ldo_init(motg, 1);
 	if (ret) {
 		dev_err(&pdev->dev, "hsusb vreg configuration failed\n");
 		goto free_hsusb_vdd;
 	}

 	if (pdata->mhl_enable) {
 		mhl_usb_hs_switch = devm_regulator_get(motg->phy.dev,
 							"mhl_usb_hs_switch");
 		if (IS_ERR(mhl_usb_hs_switch)) {
 			dev_err(&pdev->dev, "Unable to get mhl_usb_hs_switch\n");
 			ret = PTR_ERR(mhl_usb_hs_switch);
 			goto free_ldo_init;
 		}
 	}

 	ret = msm_hsusb_ldo_enable(motg, USB_PHY_REG_ON);
 	if (ret) {
 		dev_err(&pdev->dev, "hsusb vreg enable failed\n");
 		goto free_ldo_init;
 	}
 	clk_prepare_enable(motg->core_clk);

 	/* Check if USB mem_type change is needed to workaround PNOC hw issue */
 	msm_otg_pnoc_errata_fix(motg);

 	writel(0, USB_USBINTR);
 	writel(0, USB_OTGSC);
 	/* Ensure that above STOREs are completed before enabling interrupts */
 	mb();

 	ret = msm_otg_mhl_register_callback(motg, msm_otg_mhl_notify_online);
 	if (ret)
 		dev_dbg(&pdev->dev, "MHL can not be supported\n");
 	wake_lock_init(&motg->wlock, WAKE_LOCK_SUSPEND, "msm_otg");
 	msm_otg_init_timer(motg);
 	INIT_WORK(&motg->sm_work, msm_otg_sm_work);
 	INIT_DELAYED_WORK(&motg->chg_work, msm_chg_detect_work);
 	INIT_DELAYED_WORK(&motg->pmic_id_status_work, msm_pmic_id_status_w);
 	INIT_DELAYED_WORK(&motg->suspend_work, msm_otg_suspend_work);
 	setup_timer(&motg->id_timer, msm_otg_id_timer_func,
 				(unsigned long) motg);
 	setup_timer(&motg->chg_check_timer, msm_otg_chg_check_timer_func,
 				(unsigned long) motg);
 	ret = request_irq(motg->irq, msm_otg_irq, IRQF_SHARED,
 					"msm_otg", motg);
 	if (ret) {
 		dev_err(&pdev->dev, "request irq failed\n");
 		goto destroy_wlock;
 	}

 	if (motg->async_irq) {
 		ret = request_irq(motg->async_irq, msm_otg_irq,
 					IRQF_TRIGGER_RISING, "msm_otg", motg);
 		if (ret) {
 			dev_err(&pdev->dev, "request irq failed (ASYNC INT)\n");
 			goto free_irq;
 		}
 		disable_irq(motg->async_irq);
 	}

 	if (pdata->otg_control == OTG_PHY_CONTROL && pdata->mpm_otgsessvld_int)
 		msm_mpm_enable_pin(pdata->mpm_otgsessvld_int, 1);

 	if (pdata->mpm_dpshv_int)
 		msm_mpm_enable_pin(pdata->mpm_dpshv_int, 1);
 	if (pdata->mpm_dmshv_int)
 		msm_mpm_enable_pin(pdata->mpm_dmshv_int, 1);

 	phy->init = msm_otg_reset;
 	phy->set_power = msm_otg_set_power;
 	phy->set_suspend = msm_otg_set_suspend;

 	phy->io_ops = &msm_otg_io_ops;

 	phy->otg->phy = &motg->phy;
 	phy->otg->set_host = msm_otg_set_host;
 	phy->otg->set_peripheral = msm_otg_set_peripheral;
 	phy->otg->start_hnp = msm_otg_start_hnp;
 	phy->otg->start_srp = msm_otg_start_srp;
 	if (pdata->dp_manual_pullup)
 		phy->flags |= ENABLE_DP_MANUAL_PULLUP;

 	if (pdata->enable_sec_phy)
 		phy->flags |= ENABLE_SECONDARY_PHY;

 	ret = usb_set_transceiver(&motg->phy);
 	if (ret) {
 		dev_err(&pdev->dev, "usb_set_transceiver failed\n");
 		goto free_async_irq;
 	}

 	if (motg->pdata->mode == USB_OTG &&
 		motg->pdata->otg_control == OTG_PMIC_CONTROL) {
 		if (motg->pdata->pmic_id_irq) {
 			ret = request_irq(motg->pdata->pmic_id_irq,
 						msm_pmic_id_irq,
 						IRQF_TRIGGER_RISING |
 						IRQF_TRIGGER_FALLING,
 						"msm_otg", motg);
 			if (ret) {
 				dev_err(&pdev->dev, "request irq failed for PMIC ID\n");
 				goto remove_phy;
 			}
 		} else {
 			ret = -ENODEV;
 			dev_err(&pdev->dev, "PMIC IRQ for ID notifications doesn't exist\n");
 			goto remove_phy;
 		}
 	}

 	msm_hsusb_mhl_switch_enable(motg, 1);

 	platform_set_drvdata(pdev, motg);
 	device_init_wakeup(&pdev->dev, 1);
 	motg->mA_port = IUNIT;

 	ret = msm_otg_debugfs_init(motg);
 	if (ret)
 		dev_dbg(&pdev->dev, "mode debugfs file is"
 			"not available\n");

 	if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY) {
 		if (motg->pdata->otg_control == OTG_PMIC_CONTROL &&
 			(!(motg->pdata->mode == USB_OTG) ||
 			 motg->pdata->pmic_id_irq))
 			motg->caps = ALLOW_PHY_POWER_COLLAPSE |
 				ALLOW_PHY_RETENTION;

 		if (motg->pdata->otg_control == OTG_PHY_CONTROL)
 			motg->caps = ALLOW_PHY_RETENTION |
 				ALLOW_PHY_REGULATORS_LPM;

 		if (motg->pdata->mpm_dpshv_int || motg->pdata->mpm_dmshv_int)
 			motg->caps |= ALLOW_HOST_PHY_RETENTION;
 			device_create_file(&pdev->dev,
 					&dev_attr_dpdm_pulldown_enable);
 	}

 	if (motg->pdata->enable_lpm_on_dev_suspend)
 		motg->caps |= ALLOW_LPM_ON_DEV_SUSPEND;

 	if (motg->pdata->disable_retention_with_vdd_min)
 		motg->caps |= ALLOW_VDD_MIN_WITH_RETENTION_DISABLED;

 	wake_lock(&motg->wlock);
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);

 	if (motg->pdata->delay_lpm_on_disconnect) {
 		pm_runtime_set_autosuspend_delay(&pdev->dev,
 			lpm_disconnect_thresh);
 		pm_runtime_use_autosuspend(&pdev->dev);
 	}

 	motg->usb_psy.name = "usb";
 	motg->usb_psy.type = POWER_SUPPLY_TYPE_USB;
 	motg->usb_psy.supplied_to = otg_pm_power_supplied_to;
 	motg->usb_psy.num_supplicants = ARRAY_SIZE(otg_pm_power_supplied_to);
 	motg->usb_psy.properties = otg_pm_power_props_usb;
 	motg->usb_psy.num_properties = ARRAY_SIZE(otg_pm_power_props_usb);
 	motg->usb_psy.get_property = otg_power_get_property_usb;
 	motg->usb_psy.set_property = otg_power_set_property_usb;
 	motg->usb_psy.property_is_writeable
 		= otg_power_property_is_writeable_usb;

 	if (!pm8921_charger_register_vbus_sn(NULL)) {
 		/* if pm8921 use legacy implementation */
 		dev_dbg(motg->phy.dev, "%s: legacy support\n", __func__);
 		legacy_power_supply = true;
 	} else {
 		/* otherwise register our own power supply */
 		if (!msm_otg_register_power_supply(pdev, motg))
 			psy = &motg->usb_psy;
 	}

 	if (legacy_power_supply && pdata->otg_control == OTG_PMIC_CONTROL)
 		pm8921_charger_register_vbus_sn(&msm_otg_set_vbus_state);

 	ret = msm_otg_setup_ext_chg_cdev(motg);
 	if (ret)
 		dev_dbg(&pdev->dev, "fail to setup cdev\n");

 	return 0;

 remove_phy:
 	usb_set_transceiver(NULL);
 free_async_irq:
 	if (motg->async_irq)
 		free_irq(motg->async_irq, motg);
 free_irq:
 	free_irq(motg->irq, motg);
 destroy_wlock:
 	wake_lock_destroy(&motg->wlock);
 	clk_disable_unprepare(motg->core_clk);
 	msm_hsusb_ldo_enable(motg, USB_PHY_REG_OFF);
 free_ldo_init:
 	msm_hsusb_ldo_init(motg, 0);
 free_hsusb_vdd:
 	regulator_disable(hsusb_vdd);
 free_config_vddcx:
 	regulator_set_voltage(hsusb_vdd,
 		vdd_val[motg->vdd_type][VDD_NONE],
 		vdd_val[motg->vdd_type][VDD_MAX]);
 devote_xo_handle:
 	clk_disable_unprepare(motg->pclk);
 	if (!IS_ERR(motg->xo_clk))
 		clk_disable_unprepare(motg->xo_clk);
 	else
 		msm_xo_mode_vote(motg->xo_handle, MSM_XO_MODE_OFF);
 free_xo_handle:
 	if (!IS_ERR(motg->xo_clk))
 		clk_put(motg->xo_clk);
 	else
 		msm_xo_put(motg->xo_handle);
 free_regs:
 	iounmap(motg->regs);
 disable_sleep_clk:
 	if (!IS_ERR(motg->sleep_clk))
 		clk_disable_unprepare(motg->sleep_clk);
 put_pclk:
 	clk_put(motg->pclk);
 put_core_clk:
 	clk_put(motg->core_clk);
 put_clk:
 	if (!IS_ERR(motg->clk))
 		clk_put(motg->clk);
 devote_bus_bw:
 	if (motg->bus_perf_client) {
 		msm_otg_bus_vote(motg, USB_NO_PERF_VOTE);
 		msm_bus_scale_unregister_client(motg->bus_perf_client);
 	}

 	return ret;
 }

 static int __devexit msm_otg_remove(struct platform_device *pdev)
 {
 	struct msm_otg *motg = platform_get_drvdata(pdev);
 	struct usb_phy *phy = &motg->phy;
 	int cnt = 0;

 	if (phy->otg->host || phy->otg->gadget)
 		return -EBUSY;

 	if (!motg->ext_chg_device) {
 		device_destroy(motg->ext_chg_class, motg->ext_chg_dev);
 		cdev_del(&motg->ext_chg_cdev);
 		class_destroy(motg->ext_chg_class);
 		unregister_chrdev_region(motg->ext_chg_dev, 1);
 	}

 	if (pdev->dev.of_node)
 		msm_otg_setup_devices(pdev, motg->pdata->mode, false);
 	if (motg->pdata->otg_control == OTG_PMIC_CONTROL)
 		pm8921_charger_unregister_vbus_sn(0);
 	msm_otg_mhl_register_callback(motg, NULL);
 	msm_otg_debugfs_cleanup();
 	cancel_delayed_work_sync(&motg->chg_work);
 	cancel_delayed_work_sync(&motg->pmic_id_status_work);
 	cancel_delayed_work_sync(&motg->suspend_work);
 	cancel_work_sync(&motg->sm_work);

 	pm_runtime_resume(&pdev->dev);

 	device_init_wakeup(&pdev->dev, 0);
 	pm_runtime_disable(&pdev->dev);
 	wake_lock_destroy(&motg->wlock);

 	msm_hsusb_mhl_switch_enable(motg, 0);
 	if (motg->pdata->pmic_id_irq)
 		free_irq(motg->pdata->pmic_id_irq, motg);
 	usb_set_transceiver(NULL);
 	free_irq(motg->irq, motg);

 	if ((motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY) &&
 		(motg->pdata->mpm_dpshv_int || motg->pdata->mpm_dmshv_int))
 			device_remove_file(&pdev->dev,
 					&dev_attr_dpdm_pulldown_enable);
 	if (motg->pdata->otg_control == OTG_PHY_CONTROL &&
 		motg->pdata->mpm_otgsessvld_int)
 		msm_mpm_enable_pin(motg->pdata->mpm_otgsessvld_int, 0);

 	if (motg->pdata->mpm_dpshv_int)
 		msm_mpm_enable_pin(motg->pdata->mpm_dpshv_int, 0);
 	if (motg->pdata->mpm_dmshv_int)
 		msm_mpm_enable_pin(motg->pdata->mpm_dmshv_int, 0);

 	/*
 	 * Put PHY in low power mode.
 	 */
 	ulpi_read(phy, 0x14);
 	ulpi_write(phy, 0x08, 0x09);

 	writel(readl(USB_PORTSC) | PORTSC_PHCD, USB_PORTSC);
 	while (cnt < PHY_SUSPEND_TIMEOUT_USEC) {
 		if (readl(USB_PORTSC) & PORTSC_PHCD)
 			break;
 		udelay(1);
 		cnt++;
 	}
 	if (cnt >= PHY_SUSPEND_TIMEOUT_USEC)
 		dev_err(phy->dev, "Unable to suspend PHY\n");

 	clk_disable_unprepare(motg->pclk);
 	clk_disable_unprepare(motg->core_clk);
 	if (!IS_ERR(motg->xo_clk)) {
 		clk_disable_unprepare(motg->xo_clk);
 		clk_put(motg->xo_clk);
 	} else {
 		msm_xo_put(motg->xo_handle);
 	}

 	if (!IS_ERR(motg->sleep_clk))
 		clk_disable_unprepare(motg->sleep_clk);

 	msm_hsusb_ldo_enable(motg, USB_PHY_REG_OFF);
 	msm_hsusb_ldo_init(motg, 0);
 	regulator_disable(hsusb_vdd);
 	regulator_set_voltage(hsusb_vdd,
 		vdd_val[motg->vdd_type][VDD_NONE],
 		vdd_val[motg->vdd_type][VDD_MAX]);

 	iounmap(motg->regs);
 	pm_runtime_set_suspended(&pdev->dev);

 	clk_put(motg->pclk);
 	if (!IS_ERR(motg->clk))
 		clk_put(motg->clk);
 	clk_put(motg->core_clk);

 	if (motg->bus_perf_client) {
 		msm_otg_bus_vote(motg, USB_NO_PERF_VOTE);
 		msm_bus_scale_unregister_client(motg->bus_perf_client);
 	}

 	return 0;
 }

 #ifdef CONFIG_PM_RUNTIME
 static int msm_otg_runtime_idle(struct device *dev)
 {
 	struct msm_otg *motg = dev_get_drvdata(dev);
 	struct usb_phy *phy = &motg->phy;

 	dev_dbg(dev, "OTG runtime idle\n");

 	if (phy->state == OTG_STATE_UNDEFINED)
 		return -EAGAIN;

 	if (motg->ext_chg_active) {
 		dev_dbg(dev, "Deferring LPM\n");
 		/*
 		 * Charger detection may happen in user space.
 		 * Delay entering LPM by 3 sec.  Otherwise we
 		 * have to exit LPM when user space begins
 		 * charger detection.
 		 *
 		 * This timer will be canceled when user space
 		 * votes against LPM by incrementing PM usage
 		 * counter.  We enter low power mode when
 		 * PM usage counter is decremented.
 		 */
 		pm_schedule_suspend(dev, 3000);
 		return -EAGAIN;
 	}

 	return 0;
 }

 static int msm_otg_runtime_suspend(struct device *dev)
 {
 	struct msm_otg *motg = dev_get_drvdata(dev);

 	dev_dbg(dev, "OTG runtime suspend\n");
 	return msm_otg_suspend(motg);
 }

 static int msm_otg_runtime_resume(struct device *dev)
 {
 	struct msm_otg *motg = dev_get_drvdata(dev);

 	dev_dbg(dev, "OTG runtime resume\n");
 	pm_runtime_get_noresume(dev);
 	return msm_otg_resume(motg);
 }
 #endif

 #ifdef CONFIG_PM_SLEEP
 static int msm_otg_pm_suspend(struct device *dev)
 {
 	int ret = 0;
 	struct msm_otg *motg = dev_get_drvdata(dev);

 	dev_dbg(dev, "OTG PM suspend\n");

 	atomic_set(&motg->pm_suspended, 1);
 	ret = msm_otg_suspend(motg);
 	if (ret)
 		atomic_set(&motg->pm_suspended, 0);

 	return ret;
 }

 static int msm_otg_pm_resume(struct device *dev)
 {
 	int ret = 0;
 	struct msm_otg *motg = dev_get_drvdata(dev);

 	dev_dbg(dev, "OTG PM resume\n");

 	atomic_set(&motg->pm_suspended, 0);
 	if (motg->async_int || motg->sm_work_pending) {
 		pm_runtime_get_noresume(dev);
 		ret = msm_otg_resume(motg);

 		/* Update runtime PM status */
 		pm_runtime_disable(dev);
 		pm_runtime_set_active(dev);
 		pm_runtime_enable(dev);

 		if (motg->sm_work_pending) {
 			motg->sm_work_pending = false;
 			queue_work(system_nrt_wq, &motg->sm_work);
 		}
 	}

 	return ret;
 }
 #endif

 #ifdef CONFIG_PM
 static const struct dev_pm_ops msm_otg_dev_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(msm_otg_pm_suspend, msm_otg_pm_resume)
 	SET_RUNTIME_PM_OPS(msm_otg_runtime_suspend, msm_otg_runtime_resume,
 				msm_otg_runtime_idle)
 };
 #endif

 static struct of_device_id msm_otg_dt_match[] = {
 	{	.compatible = "qcom,hsusb-otg",
 	},
 	{}
 };

 static struct platform_driver msm_otg_driver = {
 	.remove = __devexit_p(msm_otg_remove),
 	.driver = {
 		.name = DRIVER_NAME,
 		.owner = THIS_MODULE,
 #ifdef CONFIG_PM
 		.pm = &msm_otg_dev_pm_ops,
 #endif
 		.of_match_table = msm_otg_dt_match,
 	},
 };

 static int __init msm_otg_init(void)
 {
 	return platform_driver_probe(&msm_otg_driver, msm_otg_probe);
 }

 static void __exit msm_otg_exit(void)
 {
 	platform_driver_unregister(&msm_otg_driver);
 }

 module_init(msm_otg_init);
 module_exit(msm_otg_exit);

 MODULE_LICENSE("GPL v2");
 MODULE_DESCRIPTION("MSM USB transceiver driver");