blob: 205e74989076192867b7ca8feb84b6f11319866a [file] [log] [blame]
/*
* Copyright (c) 2013, The Linux Foundation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 and
* only version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
&soc {
led_flash0: qcom,camera-led-flash {
cell-index = <0>;
compatible = "qcom,camera-led-flash";
qcom,flash-type = <3>;
qcom,flash-source = <&gpio_flash>;
qcom,torch-source = <&gpio_flash>;
status = "disabled";
};
};
&i2c {
qcom,camera@20 {
compatible = "shinetech,s5k4e1";
reg = <0x20>;
qcom,slave-id = <0x20 0x0000 0x4e10>;
qcom,csiphy-sd-index = <0>;
qcom,csid-sd-index = <0>;
qcom,mount-angle = <90>;
qcom,sensor-name = "SKUAB_ST_s5k4e1";
cam_vdig-supply = <&pm8110_l2>;
cam_vana-supply = <&pm8110_l19>;
cam_vio-supply = <&pm8110_l14>;
qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana";
qcom,cam-vreg-type = <0 0 0>;
qcom,cam-vreg-min-voltage = <1200000 1800000 2850000>;
qcom,cam-vreg-max-voltage = <1200000 1800000 2850000>;
qcom,cam-vreg-op-mode = <200000 8000 80000>;
qcom,gpio-no-mux = <0>;
gpios = <&msmgpio 13 0>,
<&msmgpio 21 0>,
<&msmgpio 20 0>;
qcom,gpio-reset = <1>;
qcom,gpio-standby = <2>;
qcom,gpio-req-tbl-num = <0 1 2>;
qcom,gpio-req-tbl-flags = <1 0 0>;
qcom,gpio-req-tbl-label = "CAMIF_MCLK",
"CAM_RESET1",
"CAM_STANDBY";
qcom,csi-lane-assign = <0xe4>;
qcom,csi-lane-mask = <0x3>;
qcom,sensor-position = <0>;
qcom,sensor-mode = <1>;
qcom,sensor-type = <0>;
qcom,cci-master = <0>;
};
qcom,camera@78 {
compatible = "shinetech,gc0339";
reg = <0x78>;
qcom,slave-id = <0x42 0x00 0xc8>;
qcom,csiphy-sd-index = <1>;
qcom,csid-sd-index = <1>;
qcom,mount-angle = <270>;
qcom,sensor-name = "skuab_shinetech_gc0339";
cam_vdig-supply = <&pm8110_l14>;
cam_vana-supply = <&pm8110_l19>;
cam_vio-supply = <&pm8110_l14>;
qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana";
qcom,cam-vreg-type = <0 1 0>;
qcom,cam-vreg-min-voltage = <1800000 1800000 2850000>;
qcom,cam-vreg-max-voltage = <1800000 1800000 2850000>;
qcom,cam-vreg-op-mode = <200000 0 80000>;
qcom,gpio-no-mux = <0>;
gpios = <&msmgpio 14 0>,
<&msmgpio 15 0>,
<&msmgpio 85 0>;
qcom,gpio-reset = <1>;
qcom,gpio-standby = <2>;
qcom,gpio-req-tbl-num = <0 1 2>;
qcom,gpio-req-tbl-flags = <1 0 0>;
qcom,gpio-req-tbl-label = "CAMIF_MCLK",
"CAM_RESET",
"CAM_STANDBY";
qcom,gpio-set-tbl-num = <1 1>;
qcom,gpio-set-tbl-flags = <0 2>;
qcom,gpio-set-tbl-delay = <1000 4000>;
qcom,csi-lane-assign = <0xe4>;
qcom,csi-lane-mask = <0x3>;
qcom,sensor-position = <1>;
qcom,sensor-mode = <1>;
qcom,cci-master = <0>;
status = "ok";
};
};