Documentation/s390/driver-model.txt

S/390 driver model interfaces
-----------------------------

1. CCW devices
--------------

All devices which can be addressed by means of ccws are called 'CCW devices' -
even if they aren't actually driven by ccws.

All ccw devices are accessed via a subchannel, this is reflected in the 
structures under root/:

root/
     - sys
     - legacy
     - css0/
           - 0.0.0000/0.0.0815/
	   - 0.0.0001/0.0.4711/
	   - 0.0.0002/
	   ...

In this example, device 0815 is accessed via subchannel 0, device 4711 via 
subchannel 1, and subchannel 2 is a non-I/O subchannel.

You should address a ccw device via its bus id (e.g. 0.0.4711); the device can
be found under bus/ccw/devices/.

All ccw devices export some data via sysfs.

cutype:	    The control unit type / model.

devtype:    The device type / model, if applicable.

availability: Can be 'good' or 'boxed'; 'no path' or 'no device' for
	      disconnected devices.

online:     An interface to set the device online and offline.
	    In the special case of the device being disconnected (see the
	    notify function under 1.2), piping 0 to online will focibly delete
	    the device.

The device drivers can add entries to export per-device data and interfaces.

There is also some data exported on a per-subchannel basis (see under
bus/css/devices/):

chpids:	    Via which chpids the device is connected.

pimpampom:  The path installed, path available and path operational masks.

There also might be additional data, for example for block devices.


1.1 Bringing up a ccw device
----------------------------

This is done in several steps.

a. Each driver can provide one or more parameter interfaces where parameters can
   be specified. These interfaces are also in the driver's responsibility.
b. After a. has been performed, if necessary, the device is finally brought up
   via the 'online' interface.


1.2 Writing a driver for ccw devices
------------------------------------

The basic struct ccw_device and struct ccw_driver data structures can be found
under include/asm/ccwdev.h.

struct ccw_device {
        spinlock_t *ccwlock;
        struct ccw_device_private *private;
	struct ccw_device_id id;	

	struct ccw_driver *drv;		
	struct device dev;		
	int online;

	void (*handler) (struct ccw_device *dev, unsigned long intparm,
                         struct irb *irb);
};

struct ccw_driver {
	struct module *owner;		
	struct ccw_device_id *ids;	
	int (*probe) (struct ccw_device *); 
	int (*remove) (struct ccw_device *);
	int (*set_online) (struct ccw_device *);
	int (*set_offline) (struct ccw_device *);
	int (*notify) (struct ccw_device *, int);
	struct device_driver driver;
	char *name;
};

The 'private' field contains data needed for internal i/o operation only, and
is not available to the device driver.

Each driver should declare in a MODULE_DEVICE_TABLE into which CU types/models
and/or device types/models it is interested. This information can later be found
found in the struct ccw_device_id fields:

struct ccw_device_id {
	__u16	match_flags;	

	__u16	cu_type;	
	__u16	dev_type;	
	__u8	cu_model;	
	__u8	dev_model;	

	unsigned long driver_info;
};

The functions in ccw_driver should be used in the following way:
probe:   This function is called by the device layer for each device the driver
	 is interested in. The driver should only allocate private structures
	 to put in dev->driver_data and create attributes (if needed). Also,
	 the interrupt handler (see below) should be set here.

int (*probe) (struct ccw_device *cdev); 

Parameters:  cdev     - the device to be probed.


remove:  This function is called by the device layer upon removal of the driver,
	 the device or the module. The driver should perform cleanups here.

int (*remove) (struct ccw_device *cdev);

Parameters:   cdev    - the device to be removed.


set_online: This function is called by the common I/O layer when the device is
	    activated via the 'online' attribute. The driver should finally
	    setup and activate the device here.

int (*set_online) (struct ccw_device *);

Parameters:   cdev	- the device to be activated. The common layer has
			  verified that the device is not already online.


set_offline: This function is called by the common I/O layer when the device is
	     de-activated via the 'online' attribute. The driver should shut
	     down the device, but not de-allocate its private data.

int (*set_offline) (struct ccw_device *);

Parameters:   cdev       - the device to be deactivated. The common layer has
			   verified that the device is online.


notify: This function is called by the common I/O layer for some state changes
	of the device.
	Signalled to the driver are:
	* In online state, device detached (CIO_GONE) or last path gone
	  (CIO_NO_PATH). The driver must return !0 to keep the device; for
	  return code 0, the device will be deleted as usual (also when no
	  notify function is registerd). If the driver wants to keep the
	  device, it is moved into disconnected state.
	* In disconnected state, device operational again (CIO_OPER). The
	  common I/O layer performs some sanity checks on device number and
	  Device / CU to be reasonably sure if it is still the same device.
	  If not, the old device is removed and a new one registered. By the
	  return code of the notify function the device driver signals if it
	  wants the device back: !0 for keeping, 0 to make the device being
	  removed and re-registered.
	
int (*notify) (struct ccw_device *, int);

Parameters:   cdev    - the device whose state changed.
	      event   - the event that happened. This can be one of CIO_GONE,
		        CIO_NO_PATH or CIO_OPER.

The handler field of the struct ccw_device is meant to be set to the interrupt
handler for the device. In order to accommodate drivers which use several 
distinct handlers (e.g. multi subchannel devices), this is a member of ccw_device
instead of ccw_driver.
The handler is registered with the common layer during set_online() processing
before the driver is called, and is deregistered during set_offline() after the
driver has been called. Also, after registering / before deregistering, path 
grouping resp. disbanding of the path group (if applicable) are performed.

void (*handler) (struct ccw_device *dev, unsigned long intparm, struct irb *irb);

Parameters:	dev	- the device the handler is called for
		intparm - the intparm which allows the device driver to identify
                          the i/o the interrupt is associated with, or to recognize
                          the interrupt as unsolicited.
                irb     - interruption response block which contains the accumulated
                          status.

The device driver is called from the common ccw_device layer and can retrieve 
information about the interrupt from the irb parameter.


1.3 ccwgroup devices
--------------------

The ccwgroup mechanism is designed to handle devices consisting of multiple ccw
devices, like lcs or ctc.

The ccw driver provides a 'group' attribute. Piping bus ids of ccw devices to
this attributes creates a ccwgroup device consisting of these ccw devices (if
possible). This ccwgroup device can be set online or offline just like a normal
ccw device.

Each ccwgroup device also provides an 'ungroup' attribute to destroy the device
again (only when offline). This is a generic ccwgroup mechanism (the driver does
not need to implement anything beyond normal removal routines).

To implement a ccwgroup driver, please refer to include/asm/ccwgroup.h. Keep in
mind that most drivers will need to implement both a ccwgroup and a ccw driver
(unless you have a meta ccw driver, like cu3088 for lcs and ctc).


2. Channel paths
-----------------

Channel paths show up, like subchannels, under the channel subsystem root (css0)
and are called 'chp0.<chpid>'. They have no driver and do not belong to any bus.
Please note, that unlike /proc/chpids in 2.4, the channel path objects reflect
only the logical state and not the physical state, since we cannot track the
latter consistently due to lacking machine support (we don't need to be aware
of anyway).

status - Can be 'online' or 'offline'.
	 Piping 'on' or 'off' sets the chpid logically online/offline.
	 Piping 'on' to an online chpid triggers path reprobing for all devices
	 the chpid connects to. This can be used to force the kernel to re-use
	 a channel path the user knows to be online, but the machine hasn't
	 created a machine check for.


3. System devices
-----------------

Note: cpus may yet be added here.

3.1 xpram 
---------

xpram shows up under sys/ as 'xpram'.


4. Other devices
----------------

4.1 Netiucv
-----------

The netiucv driver creates an attribute 'connection' under
bus/iucv/drivers/netiucv. Piping to this attibute creates a new netiucv
connection to the specified host.

Netiucv connections show up under devices/iucv/ as "netiucv<ifnum>". The interface
number is assigned sequentially to the connections defined via the 'connection'
attribute.

user			  - shows the connection partner.

buffer			  - maximum buffer size.
			    Pipe to it to change buffer size.