Makefile.rules - fp2-dev/platform/external/llvm - Gitiles

 #===-- Makefile.common - Common make rules for LLVM -------*- makefile -*--====
 #
 # This file is included by all of the LLVM makefiles.  This file defines common
 # rules to do things like compile a .cpp file or generate dependancy info.
 # These are platform dependant, so this is the file used to specify these
 # system dependant operations.
 #
 # The following functionality can be set by setting incoming variables.
 # The variable $(LEVEL) *must* be set:
 #
 # 1. LEVEL - The level of the current subdirectory from the top of the
 #    MagicStats view.  This level should be expressed as a path, for
 #    example, ../.. for two levels deep.
 #
 # 2. DIRS - A list of subdirectories to be built.  Fake targets are set up
 #    so that each of the targets "all", "install", and "clean" each build
 #    the subdirectories before the local target.  DIRS are guaranteed to be
 #    built in order.
 #
 # 3. PARALLEL_DIRS - A list of subdirectories to be built, but that may be
 #    built in any order.  All DIRS are built in order before PARALLEL_DIRS are
 #    built, which are then built in any order.
 #
 # 4. Source - If specified, this sets the source code filenames.  If this
 #    is not set, it defaults to be all of the .cpp, .c, .y, and .l files
 #    in the current directory.  Also, if you want to build files in addition
 #    to the local files, you can use the ExtraSource variable
 #
 #===-----------------------------------------------------------------------====

 # Configuration file to set paths specific to local installation of LLVM
 #
 include $(LEVEL)/Makefile.config

 # These are options that can either be enabled here, or can be enabled on the
 # make command line (ie, make ENABLE_PROFILING=1)
 #

 # When ENABLE_PROFILING is enabled, the llvm source base is built with profile
 # information to allow gprof to be used to get execution frequencies.
 #
 #ENABLE_PROFILING = 1

 # When ENABLE_PURIFY is enabled, the LLVM tools are linked with purify (which
 # must be locally installed) to allow for some automated memory error debugging.
 #
 #ENABLE_PURIFY    = 1

 # When ENABLE_OPTIMIZED is enabled, Release builds of all of the LLVM code are
 # turned on, and Debug builds are turned off.
 #
 #ENABLE_OPTIMIZED = 1


 # Figure out how to do platform specific stuff on this platform.  This is really
 # gross and should be autoconfiscated (automake actually), but should hopefully
 # work on Linux and solaris (SunOS).
 #
 UNAME := $(shell uname)
 include $(LEVEL)/Makefile.$(UNAME)

 ifdef SHARED_LIBRARY
 # if SHARED_LIBRARY is specified, the default is to build the dynamic lib
 dynamic ::
 endif

 # Default Rule:  Make sure it's also a :: rule
 all ::

 # Default for install is to at least build everything...
 install ::


 # Figure out which directory to build stuff into.  We want to build into the
 # /shared directory by default because it is guaranteed to be local to the
 # current machine.
 #
 ifeq ($(LLVM_OBJ_DIR),.)
 BUILD_ROOT     = $(LLVM_OBJ_DIR)
 BUILD_ROOT_TOP = $(LEVEL)
 else

 BUILD_ROOT := $(LLVM_OBJ_DIR)$(patsubst $(HOME)%,%,$(shell pwd))

 # Calculate the BUILD_ROOT_TOP variable, which is the top of the llvm/ tree.
 # Note that although this is just equal to $(BUILD_ROOT)/$(LEVEL), we cannot use
 # this expression because some of the directories on the source tree may not
 # exist in the build tree (for example the test/ heirarchy).  Thus we evaluate
 # the directory to eliminate the ../'s
 #
 TOP_DIRECTORY := $(shell cd $(LEVEL); pwd)
 BUILD_ROOT_TOP := $(LLVM_OBJ_DIR)$(patsubst $(HOME)%,%,$(TOP_DIRECTORY))
 endif

 #--------------------------------------------------------------------
 # Variables derived from configuration options...
 #--------------------------------------------------------------------

 #BinInstDir=/usr/local/bin
 #LibInstDir=/usrl/local/lib/xxx
 #DocInstDir=/usr/doc/xxx

 BURG_OPTS = -I

 PURIFY := $(PURIFY) -cache-dir="$(BUILD_ROOT_TOP)/../purifycache" -chain-length="30" -messages=all

 # Shorthand for commonly accessed directories
 LIBDEBUG    := $(BUILD_ROOT_TOP)/lib/Debug
 LIBRELEASE  := $(BUILD_ROOT_TOP)/lib/Release
 LIBPROFILE  := $(BUILD_ROOT_TOP)/lib/Profile
 TOOLDEBUG   := $(BUILD_ROOT_TOP)/tools/Debug
 TOOLRELEASE := $(BUILD_ROOT_TOP)/tools/Release
 TOOLPROFILE := $(BUILD_ROOT_TOP)/tools/Profile

 # Verbosity levels
 ifdef VERBOSE
 VERB :=
 else
 VERB := @
 endif

 #---------------------------------------------------------
 # Compilation options...
 #---------------------------------------------------------

 # Special tools used while building the LLVM tree.  Burg is built as part of the
 # utils directory.
 #
 BURG    := $(TOOLDEBUG)/burg
 RunBurg := $(BURG) $(BURG_OPTS)


 # Enable this for profiling support with 'gprof'
 # This automatically enables optimized builds.
 ifdef ENABLE_PROFILING
   PROFILE = -pg
   ENABLE_OPTIMIZED = 1
 else
   PROFILE =
 endif

 # By default, strip symbol information from executable
 ifdef KEEP_SYMBOLS
 STRIP =
 STRIP_WARN_MSG =
 else
 STRIP = $(PLATFORMSTRIPOPTS)
 STRIP_WARN_MSG = "(without symbols) "
 endif

 # Allow gnu extensions...
 CPPFLAGS += -D_GNU_SOURCE

 # -Wno-unused-parameter
 CompileCommonOpts := -Wall -W  -Wwrite-strings -Wno-unused -I$(LEVEL)/include
 CompileOptimizeOpts := -O3 -DNDEBUG -finline-functions -fshort-enums

 # Compile a cpp file, don't link...
 Compile  := $(CXX) -c $(CPPFLAGS) $(CXXFLAGS) $(CompileCommonOpts)
 CompileG := $(Compile) -g  -D_DEBUG
 CompileO := $(Compile) $(CompileOptimizeOpts) -felide-constructors -fomit-frame-pointer
 CompileP := $(Compile) $(CompileOptimizeOpts) -felide-constructors $(PROFILE)

 # Compile a c file, don't link...
 CompileC  := $(CC) -c $(CPPFLAGS) $(CCFLAGS) $(CompileCommonOpts)
 CompileCG := $(CompileC) -g  -D_DEBUG
 CompileCO := $(CompileC) $(CompileOptimizeOpts) -fomit-frame-pointer
 CompileCP := $(CompileC) $(CompileOptimizeOpts) $(PROFILE)


 # Link final executable

 ifdef ENABLE_PURIFY # To enable purify, build with 'gmake ENABLE_PURIFY=1'
 Link     := $(PURIFY) $(CXX) -static
 else
 Link     := $(CXX)
 endif
 LinkG    := $(Link) -g  -L$(LIBDEBUG) $(STRIP)
 LinkO    := $(Link) -O3 -L$(LIBRELEASE)
 LinkP    := $(Link) -O3 -L$(LIBPROFILE) $(PROFILE)

 # Create one .o file from a bunch of .o files...
 Relink = ld -r

 # MakeSO - Create a .so file from a .o files...
 MakeSO   := $(CXX) $(MakeSharedObjectOption)
 MakeSOO  := $(MakeSO) -O3
 MakeSOP  := $(MakeSOO) $(PROFILE)

 # Create dependancy file from CPP file, send to stdout.
 Depend   := $(CXX) -MM -I$(LEVEL)/include $(CPPFLAGS)
 DependC  := $(CC)  -MM -I$(LEVEL)/include $(CPPFLAGS)

 # Archive a bunch of .o files into a .a file...
 AR       = ar cq
 BISON    = bison

 #----------------------------------------------------------

 # Source includes all of the cpp files, and objects are derived from the
 # source files...
 # The local Makefile can list other Source files via ExtraSource = ...
 #
 ifndef Source
 Source  := $(ExtraSource) $(wildcard *.cpp *.c *.y *.l)
 endif

 Objs := $(sort $(patsubst Debug/%.o, %.o, $(addsuffix .o,$(basename $(Source)))))
 ObjectsO := $(addprefix $(BUILD_ROOT)/Release/,$(Objs))
 ObjectsP := $(addprefix $(BUILD_ROOT)/Profile/,$(Objs))
 ObjectsG := $(addprefix $(BUILD_ROOT)/Debug/,$(Objs))


 #---------------------------------------------------------
 # Handle the DIRS and PARALLEL_DIRS options
 #---------------------------------------------------------

 ifdef DIRS
 all install clean test ::
 	$(VERB) for dir in ${DIRS}; do \
 		(cd $$dir; $(MAKE) $@) || exit 1; \
 	done
 endif

 # Handle PARALLEL_DIRS
 ifdef PARALLEL_DIRS
 all     :: $(addsuffix /.makeall    , $(PARALLEL_DIRS))
 install :: $(addsuffix /.makeinstall, $(PARALLEL_DIRS))
 clean   :: $(addsuffix /.makeclean  , $(PARALLEL_DIRS))
 test    :: $(addsuffix /.maketest   , $(PARALLEL_DIRS))

 %/.makeall %/.makeinstall %/.makeclean %/.maketest:
 	$(VERB) cd $(@D); $(MAKE) $(subst $(@D)/.make,,$@)
 endif

 #---------------------------------------------------------
 # Handle the LIBRARYNAME option - used when building libs...
 #---------------------------------------------------------
 #
 #  When libraries are built, they are allowed to optionally define the
 #  DONT_BUILD_RELINKED make variable, which, when defined, prevents a .o file
 #  from being built for the library. This .o files may then be linked to by a
 #  tool if the tool does not need (or want) the semantics a .a file provides
 #  (linking in only object files that are "needed").  If a library is never to
 #  be used in this way, it is better to define DONT_BUILD_RELINKED, and define
 #  BUILD_ARCHIVE instead.
 #
 #  Some libraries must be built as .a files (libscalar for example) because if
 #  it's built as a .o file, then all of the constituent .o files in it will be
 #  linked into tools (for example gccas) even if they only use one of the parts
 #  of it.  For this reason, sometimes it's useful to use libraries as .a files.

 ifdef LIBRARYNAME

 # Make sure there isn't any extranous whitespace on the LIBRARYNAME option
 LIBRARYNAME := $(strip $(LIBRARYNAME))

 LIBNAME_O    := $(LIBRELEASE)/lib$(LIBRARYNAME).so
 LIBNAME_P    := $(LIBPROFILE)/lib$(LIBRARYNAME).so
 LIBNAME_G    := $(LIBDEBUG)/lib$(LIBRARYNAME).so
 LIBNAME_AO   := $(LIBRELEASE)/lib$(LIBRARYNAME).a
 LIBNAME_AP   := $(LIBPROFILE)/lib$(LIBRARYNAME).a
 LIBNAME_AG   := $(LIBDEBUG)/lib$(LIBRARYNAME).a
 LIBNAME_OBJO := $(LIBRELEASE)/$(LIBRARYNAME).o
 LIBNAME_OBJP := $(LIBPROFILE)/$(LIBRARYNAME).o
 LIBNAME_OBJG := $(LIBDEBUG)/$(LIBRARYNAME).o


 ifndef ENABLE_OPTIMIZED
 BUILD_LIBNAME_G := $(LIBNAME_G)
 ifndef DONT_BUILD_RELINKED
 BUILD_LIBNAME_OBJG := $(LIBNAME_OBJG)
 endif
 ifdef BUILD_ARCHIVE
 BUILD_LIBNAME_AG := $(LIBNAME_AG)
 endif
 endif

 # If optimized builds are enabled...
 ifdef ENABLE_OPTIMIZED
   ifdef ENABLE_PROFILING
     BUILD_LIBNAME_O  := $(LIBNAME_P)
     ifndef DONT_BUILD_RELINKED
       BUILD_LIBNAME_OBJO := $(LIBNAME_OBJP)
     endif
     ifdef BUILD_ARCHIVE
       BUILD_LIBNAME_AO := $(LIBNAME_AP)
     endif
   else
     BUILD_LIBNAME_O  := $(LIBNAME_O)
     ifndef DONT_BUILD_RELINKED
       BUILD_LIBNAME_OBJO := $(LIBNAME_OBJO)
     endif
     ifdef BUILD_ARCHIVE
       BUILD_LIBNAME_AO := $(LIBNAME_AO)
     endif
   endif
 endif

 all:: $(BUILD_LIBNAME_AG) $(BUILD_LIBNAME_OBJG)      # Debug
 all:: $(BUILD_LIBNAME_AO) $(BUILD_LIBNAME_OBJO)      # Release
 all:: $(BUILD_LIBNAME_AP) $(BUILD_LIBNAME_OBJP)      # Profile
 dynamic:: $(BUILD_LIBNAME_G) $(BUILD_LIBNAME_O) $(BUILD_LIBNAME_P) # .so files

 $(LIBNAME_O): $(ObjectsO) $(LibSubDirs) $(LIBRELEASE)/.dir
 	@echo ======= Linking $(LIBRARYNAME) release library =======
 	$(VERB) $(MakeSOO) -o $@ $(ObjectsO) $(LibSubDirs) $(LibLinkOpts)

 $(LIBNAME_P): $(ObjectsP) $(LibSubDirs) $(LIBPROFILE)/.dir
 	@echo ======= Linking $(LIBRARYNAME) profile library =======
 	$(VERB) $(MakeSOP) -o $@ $(ObjectsP) $(LibSubDirs) $(LibLinkOpts)

 $(LIBNAME_G): $(ObjectsG) $(LibSubDirs) $(LIBDEBUG)/.dir
 	@echo ======= Linking $(LIBRARYNAME) debug library =======
 	$(VERB) $(MakeSO) -g -o $@ $(ObjectsG) $(LibSubDirs) $(LibLinkOpts)

 $(LIBNAME_AO): $(ObjectsO) $(LibSubDirs) $(LIBRELEASE)/.dir
 	@echo ======= Linking $(LIBRARYNAME) release library =======
 	@rm -f $@
 	$(VERB) $(AR) $@ $(ObjectsO) $(LibSubDirs)

 $(LIBNAME_AP): $(ObjectsP) $(LibSubDirs) $(LIBPROFILE)/.dir
 	@echo ======= Linking $(LIBRARYNAME) profile library =======
 	@rm -f $@
 	$(VERB) $(AR) $@ $(ObjectsP) $(LibSubDirs)

 $(LIBNAME_AG): $(ObjectsG) $(LibSubDirs) $(LIBDEBUG)/.dir
 	@echo ======= Linking $(LIBRARYNAME) debug library =======
 	@rm -f $@
 	$(VERB) $(AR) $@ $(ObjectsG) $(LibSubDirs)

 $(LIBNAME_OBJO): $(ObjectsO) $(LibSubDirs) $(LIBRELEASE)/.dir
 	@echo "Linking $@"
 	$(VERB) $(Relink) -o $@ $(ObjectsO) $(LibSubDirs)

 $(LIBNAME_OBJP): $(ObjectsP) $(LibSubDirs) $(LIBPROFILE)/.dir
 	@echo "Linking $@"
 	$(VERB) $(Relink) -o $@ $(ObjectsP) $(LibSubDirs)

 $(LIBNAME_OBJG): $(ObjectsG) $(LibSubDirs) $(LIBDEBUG)/.dir
 	@echo "Linking $@"
 	$(VERB) $(Relink) -o $@ $(ObjectsG) $(LibSubDirs)

 endif

 #------------------------------------------------------------------------
 # Create a TAGS database for emacs
 #------------------------------------------------------------------------

 ifeq ($(LEVEL), .)
 tags:
 	etags -l c++ `find include lib tools -name '*.cpp' -o -name '*.h'`
 all:: tags
 endif

 #------------------------------------------------------------------------
 # Handle the TOOLNAME option - used when building tool executables...
 #------------------------------------------------------------------------
 #
 # The TOOLNAME option should be used with a USEDLIBS variable that tells the
 # libraries (and the order of the libs) that should be linked to the
 # tool. USEDLIBS should contain a list of library names (some with .a extension)
 # that are automatically linked in as .o files unless the .a suffix is added.
 #
 ifdef TOOLNAME

 # TOOLEXENAME* - These compute the output filenames to generate...
 TOOLEXENAME_G := $(BUILD_ROOT_TOP)/tools/Debug/$(TOOLNAME)
 TOOLEXENAME_O := $(BUILD_ROOT_TOP)/tools/Release/$(TOOLNAME)
 TOOLEXENAME_P := $(BUILD_ROOT_TOP)/tools/Profile/$(TOOLNAME)

 ifndef ENABLE_OPTIMIZED
   TOOLEXENAMES  := $(TOOLEXENAME_G)
 else
   ifdef ENABLE_PROFILING
     TOOLEXENAMES := $(TOOLEXENAME_P)
   else
     TOOLEXENAMES := $(TOOLEXENAME_O)
   endif
 endif

 # USED_LIBS_OPTIONS - Compute the options line that add -llib1 -llib2, etc.
 USED_LIBS_OPTIONS   := $(patsubst %.a.o, -l%, $(addsuffix .o, $(USEDLIBS)))
 USED_LIBS_OPTIONS_G := $(patsubst %.o, $(LIBDEBUG)/%.o,  $(USED_LIBS_OPTIONS))
 USED_LIBS_OPTIONS_O := $(patsubst %.o, $(LIBRELEASE)/%.o,$(USED_LIBS_OPTIONS))
 USED_LIBS_OPTIONS_P := $(patsubst %.o, $(LIBPROFILE)/%.o,$(USED_LIBS_OPTIONS))


 # USED_LIB_PATHS - Compute the path of the libraries used so that tools are
 # rebuilt if libraries change.  This has to make sure to handle .a/.so and .o
 # files seperately.
 #
 STATICUSEDLIBS   := $(patsubst %.a.o, lib%.a, $(addsuffix .o, $(USEDLIBS)))
 USED_LIB_PATHS_G := $(addprefix $(LIBDEBUG)/, $(STATICUSEDLIBS))
 USED_LIB_PATHS_O := $(addprefix $(LIBRELEASE)/, $(STATICUSEDLIBS))
 USED_LIB_PATHS_P := $(addprefix $(LIBPROFILE)/, $(STATICUSEDLIBS))
 LINK_OPTS        := $(TOOLLINKOPTS) $(PLATFORMLINKOPTS)


 # Tell make that we need to rebuild subdirectories before we can link the tool.
 # This affects things like LLI which has library subdirectories.
 $(USED_LIB_PATHS_G) $(USED_LIB_PATHS_O) $(USED_LIB_PATHS_P): \
         $(addsuffix /.makeall, $(PARALLEL_DIRS))

 all::   $(TOOLEXENAMES)
 clean::
 	$(VERB) rm -f $(TOOLEXENAMES)

 $(TOOLEXENAME_G): $(ObjectsG) $(USED_LIB_PATHS_G) $(TOOLDEBUG)/.dir
 	@echo ======= Linking $(TOOLNAME) debug executable $(STRIP_WARN_MSG) =======
 	$(VERB) $(LinkG) -o $@ $(ObjectsG) $(USED_LIBS_OPTIONS_G) $(LINK_OPTS)

 $(TOOLEXENAME_O): $(ObjectsO) $(USED_LIB_PATHS_O) $(TOOLRELEASE)/.dir
 	@echo ======= Linking $(TOOLNAME) release executable =======
 	$(VERB) $(LinkO) -o $@ $(ObjectsO) $(USED_LIBS_OPTIONS_O) $(LINK_OPTS)

 $(TOOLEXENAME_P): $(ObjectsP) $(USED_LIB_PATHS_P) $(TOOLPROFILE)/.dir
 	@echo ======= Linking $(TOOLNAME) profile executable =======
 	$(VERB) $(LinkP) -o $@ $(ObjectsP) $(USED_LIBS_OPTIONS_P) $(LINK_OPTS)

 endif


 #---------------------------------------------------------
 .PRECIOUS: $(BUILD_ROOT)/Depend/.dir
 .PRECIOUS: $(BUILD_ROOT)/Debug/.dir $(BUILD_ROOT)/Release/.dir

 # Create dependencies for the *.cpp files...
 $(BUILD_ROOT)/Depend/%.d: %.cpp $(BUILD_ROOT)/Depend/.dir
 	$(VERB) $(Depend) $< | sed 's|$*\.o *|$(BUILD_ROOT)/Release/& $(BUILD_ROOT)/Profile/& $(BUILD_ROOT)/Debug/& $(BUILD_ROOT)/Depend/$(@F)|g' > $@

 # Create dependencies for the *.c files...
 $(BUILD_ROOT)/Depend/%.d: %.c $(BUILD_ROOT)/Depend/.dir
 	$(VERB) $(DependC) $< | sed 's|$*\.o *|Release/& Profile/& Debug/& Depend/$(@F)|g' > $@

 # Create .o files in the ObjectFiles directory from the .cpp and .c files...
 $(BUILD_ROOT)/Release/%.o: %.cpp $(BUILD_ROOT)/Release/.dir
 	@echo "Compiling $<"
 	$(VERB) $(CompileO) $< -o $@

 $(BUILD_ROOT)/Release/%.o: %.c $(BUILD_ROOT)/Release/.dir
 	$(VERB) $(CompileCO) $< -o $@

 $(BUILD_ROOT)/Profile/%.o: %.cpp $(BUILD_ROOT)/Profile/.dir
 	@echo "Compiling $<"
 	$(VERB) $(CompileP) $< -o $@

 $(BUILD_ROOT)/Profile/%.o: %.c $(BUILD_ROOT)/Profile/.dir
 	@echo "Compiling $<"
 	$(VERB) $(CompileCP) $< -o $@

 $(BUILD_ROOT)/Debug/%.o: %.cpp $(BUILD_ROOT)/Debug/.dir
 	@echo "Compiling $<"
 	$(VERB) $(CompileG) $< -o $@

 $(BUILD_ROOT)/Debug/%.o: %.c $(BUILD_ROOT)/Debug/.dir
 	$(VERB) $(CompileCG) $< -o $@

 #
 # Rules for building lex/yacc files
 #
 LEX_FILES   = $(filter %.l, $(Source))
 LEX_OUTPUT  = $(LEX_FILES:%.l=%.cpp)
 YACC_FILES  = $(filter %.y, $(Source))
 YACC_OUTPUT = $(addprefix $(YACC_FILES:%.y=%), .h .cpp .output)
 .PRECIOUS: $(LEX_OUTPUT) $(YACC_OUTPUT)

 # Create a .cpp source file from a flex input file... this uses sed to cut down
 # on the warnings emited by GCC...
 #
 # The last line is a gross hack to work around flex aparently not being able to
 # resize the buffer on a large token input.  Currently, for uninitialized string
 # buffers in LLVM we can generate very long tokens, so this is a hack around it.
 # FIXME.  (f.e. char Buffer[10000]; )
 #
 %.cpp: %.l
 	flex -t $< | sed '/^find_rule/d' | \
                      sed 's/void yyunput/inline void yyunput/' | \
           sed 's/void \*yy_flex_realloc/inline void *yy_flex_realloc/' | \
           sed 's/#define YY_BUF_SIZE 16384/#define YY_BUF_SIZE (16384*64)/' > $@

 # Rule for building the bison parsers...

 %.cpp %.h : %.y
 	$(VERB) $(BISON) -v -d -p $(<:%Parser.y=%) $*.y
 	$(VERB) mv -f $*.tab.c $*.cpp
 	$(VERB) mv -f $*.tab.h $*.h

 # To create the directories...
 %/.dir:
 	$(VERB) mkdir -p $*
 	@date > $@

 # To create postscript files from dot files...
 %.ps: %.dot
 	dot -Tps < $< > $@

 # 'make clean' nukes the tree
 clean::
 	$(VERB) rm -rf $(BUILD_ROOT)/Debug $(BUILD_ROOT)/Release $(BUILD_ROOT)/Profile $(BUILD_ROOT)/Depend
 	$(VERB) rm -f core core.[0-9][0-9]* *.o *.d *.so *~ *.flc
 	$(VERB) rm -f $(LEX_OUTPUT) $(YACC_OUTPUT)

 # If dependancies were generated for the file that included this file,
 # include the dependancies now...
 #
 SourceDepend := $(addsuffix .d,$(addprefix $(BUILD_ROOT)/Depend/,$(basename $(filter-out Debug/%, $(Source)))))
 ifneq ($(SourceDepend),)
 -include $(SourceDepend)
 endif
	#===-- Makefile.common - Common make rules for LLVM -------- makefile ---====
	#
	# This file is included by all of the LLVM makefiles. This file defines common
	# rules to do things like compile a .cpp file or generate dependancy info.
	# These are platform dependant, so this is the file used to specify these
	# system dependant operations.
	#
	# The following functionality can be set by setting incoming variables.
	# The variable $(LEVEL) must be set:
	#
	# 1. LEVEL - The level of the current subdirectory from the top of the
	# MagicStats view. This level should be expressed as a path, for
	# example, ../.. for two levels deep.
	#
	# 2. DIRS - A list of subdirectories to be built. Fake targets are set up
	# so that each of the targets "all", "install", and "clean" each build
	# the subdirectories before the local target. DIRS are guaranteed to be
	# built in order.
	#
	# 3. PARALLEL_DIRS - A list of subdirectories to be built, but that may be
	# built in any order. All DIRS are built in order before PARALLEL_DIRS are
	# built, which are then built in any order.
	#
	# 4. Source - If specified, this sets the source code filenames. If this
	# is not set, it defaults to be all of the .cpp, .c, .y, and .l files
	# in the current directory. Also, if you want to build files in addition
	# to the local files, you can use the ExtraSource variable
	#
	#===-----------------------------------------------------------------------====

	# Configuration file to set paths specific to local installation of LLVM
	#
	include $(LEVEL)/Makefile.config

	# These are options that can either be enabled here, or can be enabled on the
	# make command line (ie, make ENABLE_PROFILING=1)
	#

	# When ENABLE_PROFILING is enabled, the llvm source base is built with profile
	# information to allow gprof to be used to get execution frequencies.
	#
	#ENABLE_PROFILING = 1

	# When ENABLE_PURIFY is enabled, the LLVM tools are linked with purify (which
	# must be locally installed) to allow for some automated memory error debugging.
	#
	#ENABLE_PURIFY = 1

	# When ENABLE_OPTIMIZED is enabled, Release builds of all of the LLVM code are
	# turned on, and Debug builds are turned off.
	#
	#ENABLE_OPTIMIZED = 1


	# Figure out how to do platform specific stuff on this platform. This is really
	# gross and should be autoconfiscated (automake actually), but should hopefully
	# work on Linux and solaris (SunOS).
	#
	UNAME := $(shell uname)
	include $(LEVEL)/Makefile.$(UNAME)

	ifdef SHARED_LIBRARY
	# if SHARED_LIBRARY is specified, the default is to build the dynamic lib
	dynamic ::
	endif

	# Default Rule: Make sure it's also a :: rule
	all ::

	# Default for install is to at least build everything...
	install ::


	# Figure out which directory to build stuff into. We want to build into the
	# /shared directory by default because it is guaranteed to be local to the
	# current machine.
	#
	ifeq ($(LLVM_OBJ_DIR),.)
	BUILD_ROOT = $(LLVM_OBJ_DIR)
	BUILD_ROOT_TOP = $(LEVEL)
	else

	BUILD_ROOT := $(LLVM_OBJ_DIR)$(patsubst $(HOME)%,%,$(shell pwd))

	# Calculate the BUILD_ROOT_TOP variable, which is the top of the llvm/ tree.
	# Note that although this is just equal to $(BUILD_ROOT)/$(LEVEL), we cannot use
	# this expression because some of the directories on the source tree may not
	# exist in the build tree (for example the test/ heirarchy). Thus we evaluate
	# the directory to eliminate the ../'s
	#
	TOP_DIRECTORY := $(shell cd $(LEVEL); pwd)
	BUILD_ROOT_TOP := $(LLVM_OBJ_DIR)$(patsubst $(HOME)%,%,$(TOP_DIRECTORY))
	endif

	#--------------------------------------------------------------------
	# Variables derived from configuration options...
	#--------------------------------------------------------------------

	#BinInstDir=/usr/local/bin
	#LibInstDir=/usrl/local/lib/xxx
	#DocInstDir=/usr/doc/xxx

	BURG_OPTS = -I

	PURIFY := $(PURIFY) -cache-dir="$(BUILD_ROOT_TOP)/../purifycache" -chain-length="30" -messages=all

	# Shorthand for commonly accessed directories
	LIBDEBUG := $(BUILD_ROOT_TOP)/lib/Debug
	LIBRELEASE := $(BUILD_ROOT_TOP)/lib/Release
	LIBPROFILE := $(BUILD_ROOT_TOP)/lib/Profile
	TOOLDEBUG := $(BUILD_ROOT_TOP)/tools/Debug
	TOOLRELEASE := $(BUILD_ROOT_TOP)/tools/Release
	TOOLPROFILE := $(BUILD_ROOT_TOP)/tools/Profile

	# Verbosity levels
	ifdef VERBOSE
	VERB :=
	else
	VERB := @
	endif

	#---------------------------------------------------------
	# Compilation options...
	#---------------------------------------------------------

	# Special tools used while building the LLVM tree. Burg is built as part of the
	# utils directory.
	#
	BURG := $(TOOLDEBUG)/burg
	RunBurg := $(BURG) $(BURG_OPTS)


	# Enable this for profiling support with 'gprof'
	# This automatically enables optimized builds.
	ifdef ENABLE_PROFILING
	PROFILE = -pg
	ENABLE_OPTIMIZED = 1
	else
	PROFILE =
	endif

	# By default, strip symbol information from executable
	ifdef KEEP_SYMBOLS
	STRIP =
	STRIP_WARN_MSG =
	else
	STRIP = $(PLATFORMSTRIPOPTS)
	STRIP_WARN_MSG = "(without symbols) "
	endif

	# Allow gnu extensions...
	CPPFLAGS += -D_GNU_SOURCE

	# -Wno-unused-parameter
	CompileCommonOpts := -Wall -W -Wwrite-strings -Wno-unused -I$(LEVEL)/include
	CompileOptimizeOpts := -O3 -DNDEBUG -finline-functions -fshort-enums

	# Compile a cpp file, don't link...
	Compile := $(CXX) -c $(CPPFLAGS) $(CXXFLAGS) $(CompileCommonOpts)
	CompileG := $(Compile) -g -D_DEBUG
	CompileO := $(Compile) $(CompileOptimizeOpts) -felide-constructors -fomit-frame-pointer
	CompileP := $(Compile) $(CompileOptimizeOpts) -felide-constructors $(PROFILE)

	# Compile a c file, don't link...
	CompileC := $(CC) -c $(CPPFLAGS) $(CCFLAGS) $(CompileCommonOpts)
	CompileCG := $(CompileC) -g -D_DEBUG
	CompileCO := $(CompileC) $(CompileOptimizeOpts) -fomit-frame-pointer
	CompileCP := $(CompileC) $(CompileOptimizeOpts) $(PROFILE)


	# Link final executable

	ifdef ENABLE_PURIFY # To enable purify, build with 'gmake ENABLE_PURIFY=1'
	Link := $(PURIFY) $(CXX) -static
	else
	Link := $(CXX)
	endif
	LinkG := $(Link) -g -L$(LIBDEBUG) $(STRIP)
	LinkO := $(Link) -O3 -L$(LIBRELEASE)
	LinkP := $(Link) -O3 -L$(LIBPROFILE) $(PROFILE)

	# Create one .o file from a bunch of .o files...
	Relink = ld -r

	# MakeSO - Create a .so file from a .o files...
	MakeSO := $(CXX) $(MakeSharedObjectOption)
	MakeSOO := $(MakeSO) -O3
	MakeSOP := $(MakeSOO) $(PROFILE)

	# Create dependancy file from CPP file, send to stdout.
	Depend := $(CXX) -MM -I$(LEVEL)/include $(CPPFLAGS)
	DependC := $(CC) -MM -I$(LEVEL)/include $(CPPFLAGS)

	# Archive a bunch of .o files into a .a file...
	AR = ar cq
	BISON = bison

	#----------------------------------------------------------

	# Source includes all of the cpp files, and objects are derived from the
	# source files...
	# The local Makefile can list other Source files via ExtraSource = ...
	#
	ifndef Source
	Source := $(ExtraSource) $(wildcard .cpp .c .y .l)
	endif

	Objs := $(sort $(patsubst Debug/%.o, %.o, $(addsuffix .o,$(basename $(Source)))))
	ObjectsO := $(addprefix $(BUILD_ROOT)/Release/,$(Objs))
	ObjectsP := $(addprefix $(BUILD_ROOT)/Profile/,$(Objs))
	ObjectsG := $(addprefix $(BUILD_ROOT)/Debug/,$(Objs))


	#---------------------------------------------------------
	# Handle the DIRS and PARALLEL_DIRS options
	#---------------------------------------------------------

	ifdef DIRS
	all install clean test ::
	$(VERB) for dir in ${DIRS}; do \
	(cd $$dir; $(MAKE) $@) \|\| exit 1; \
	done
	endif

	# Handle PARALLEL_DIRS
	ifdef PARALLEL_DIRS
	all :: $(addsuffix /.makeall , $(PARALLEL_DIRS))
	install :: $(addsuffix /.makeinstall, $(PARALLEL_DIRS))
	clean :: $(addsuffix /.makeclean , $(PARALLEL_DIRS))
	test :: $(addsuffix /.maketest , $(PARALLEL_DIRS))

	%/.makeall %/.makeinstall %/.makeclean %/.maketest:
	$(VERB) cd $(@D); $(MAKE) $(subst $(@D)/.make,,$@)
	endif

	#---------------------------------------------------------
	# Handle the LIBRARYNAME option - used when building libs...
	#---------------------------------------------------------
	#
	# When libraries are built, they are allowed to optionally define the
	# DONT_BUILD_RELINKED make variable, which, when defined, prevents a .o file
	# from being built for the library. This .o files may then be linked to by a
	# tool if the tool does not need (or want) the semantics a .a file provides
	# (linking in only object files that are "needed"). If a library is never to
	# be used in this way, it is better to define DONT_BUILD_RELINKED, and define
	# BUILD_ARCHIVE instead.
	#
	# Some libraries must be built as .a files (libscalar for example) because if
	# it's built as a .o file, then all of the constituent .o files in it will be
	# linked into tools (for example gccas) even if they only use one of the parts
	# of it. For this reason, sometimes it's useful to use libraries as .a files.

	ifdef LIBRARYNAME

	# Make sure there isn't any extranous whitespace on the LIBRARYNAME option
	LIBRARYNAME := $(strip $(LIBRARYNAME))

	LIBNAME_O := $(LIBRELEASE)/lib$(LIBRARYNAME).so
	LIBNAME_P := $(LIBPROFILE)/lib$(LIBRARYNAME).so
	LIBNAME_G := $(LIBDEBUG)/lib$(LIBRARYNAME).so
	LIBNAME_AO := $(LIBRELEASE)/lib$(LIBRARYNAME).a
	LIBNAME_AP := $(LIBPROFILE)/lib$(LIBRARYNAME).a
	LIBNAME_AG := $(LIBDEBUG)/lib$(LIBRARYNAME).a
	LIBNAME_OBJO := $(LIBRELEASE)/$(LIBRARYNAME).o
	LIBNAME_OBJP := $(LIBPROFILE)/$(LIBRARYNAME).o
	LIBNAME_OBJG := $(LIBDEBUG)/$(LIBRARYNAME).o


	ifndef ENABLE_OPTIMIZED
	BUILD_LIBNAME_G := $(LIBNAME_G)
	ifndef DONT_BUILD_RELINKED
	BUILD_LIBNAME_OBJG := $(LIBNAME_OBJG)
	endif
	ifdef BUILD_ARCHIVE
	BUILD_LIBNAME_AG := $(LIBNAME_AG)
	endif
	endif

	# If optimized builds are enabled...
	ifdef ENABLE_OPTIMIZED
	ifdef ENABLE_PROFILING
	BUILD_LIBNAME_O := $(LIBNAME_P)
	ifndef DONT_BUILD_RELINKED
	BUILD_LIBNAME_OBJO := $(LIBNAME_OBJP)
	endif
	ifdef BUILD_ARCHIVE
	BUILD_LIBNAME_AO := $(LIBNAME_AP)
	endif
	else
	BUILD_LIBNAME_O := $(LIBNAME_O)
	ifndef DONT_BUILD_RELINKED
	BUILD_LIBNAME_OBJO := $(LIBNAME_OBJO)
	endif
	ifdef BUILD_ARCHIVE
	BUILD_LIBNAME_AO := $(LIBNAME_AO)
	endif
	endif
	endif

	all:: $(BUILD_LIBNAME_AG) $(BUILD_LIBNAME_OBJG) # Debug
	all:: $(BUILD_LIBNAME_AO) $(BUILD_LIBNAME_OBJO) # Release
	all:: $(BUILD_LIBNAME_AP) $(BUILD_LIBNAME_OBJP) # Profile
	dynamic:: $(BUILD_LIBNAME_G) $(BUILD_LIBNAME_O) $(BUILD_LIBNAME_P) # .so files

	$(LIBNAME_O): $(ObjectsO) $(LibSubDirs) $(LIBRELEASE)/.dir
	@echo ======= Linking $(LIBRARYNAME) release library =======
	$(VERB) $(MakeSOO) -o $@ $(ObjectsO) $(LibSubDirs) $(LibLinkOpts)

	$(LIBNAME_P): $(ObjectsP) $(LibSubDirs) $(LIBPROFILE)/.dir
	@echo ======= Linking $(LIBRARYNAME) profile library =======
	$(VERB) $(MakeSOP) -o $@ $(ObjectsP) $(LibSubDirs) $(LibLinkOpts)

	$(LIBNAME_G): $(ObjectsG) $(LibSubDirs) $(LIBDEBUG)/.dir
	@echo ======= Linking $(LIBRARYNAME) debug library =======
	$(VERB) $(MakeSO) -g -o $@ $(ObjectsG) $(LibSubDirs) $(LibLinkOpts)

	$(LIBNAME_AO): $(ObjectsO) $(LibSubDirs) $(LIBRELEASE)/.dir
	@echo ======= Linking $(LIBRARYNAME) release library =======
	@rm -f $@
	$(VERB) $(AR) $@ $(ObjectsO) $(LibSubDirs)

	$(LIBNAME_AP): $(ObjectsP) $(LibSubDirs) $(LIBPROFILE)/.dir
	@echo ======= Linking $(LIBRARYNAME) profile library =======
	@rm -f $@
	$(VERB) $(AR) $@ $(ObjectsP) $(LibSubDirs)

	$(LIBNAME_AG): $(ObjectsG) $(LibSubDirs) $(LIBDEBUG)/.dir
	@echo ======= Linking $(LIBRARYNAME) debug library =======
	@rm -f $@
	$(VERB) $(AR) $@ $(ObjectsG) $(LibSubDirs)

	$(LIBNAME_OBJO): $(ObjectsO) $(LibSubDirs) $(LIBRELEASE)/.dir
	@echo "Linking $@"
	$(VERB) $(Relink) -o $@ $(ObjectsO) $(LibSubDirs)

	$(LIBNAME_OBJP): $(ObjectsP) $(LibSubDirs) $(LIBPROFILE)/.dir
	@echo "Linking $@"
	$(VERB) $(Relink) -o $@ $(ObjectsP) $(LibSubDirs)

	$(LIBNAME_OBJG): $(ObjectsG) $(LibSubDirs) $(LIBDEBUG)/.dir
	@echo "Linking $@"
	$(VERB) $(Relink) -o $@ $(ObjectsG) $(LibSubDirs)

	endif

	#------------------------------------------------------------------------
	# Create a TAGS database for emacs
	#------------------------------------------------------------------------

	ifeq ($(LEVEL), .)
	tags:
	etags -l c++ `find include lib tools -name '.cpp' -o -name '.h'`
	all:: tags
	endif

	#------------------------------------------------------------------------
	# Handle the TOOLNAME option - used when building tool executables...
	#------------------------------------------------------------------------
	#
	# The TOOLNAME option should be used with a USEDLIBS variable that tells the
	# libraries (and the order of the libs) that should be linked to the
	# tool. USEDLIBS should contain a list of library names (some with .a extension)
	# that are automatically linked in as .o files unless the .a suffix is added.
	#
	ifdef TOOLNAME

	# TOOLEXENAME* - These compute the output filenames to generate...
	TOOLEXENAME_G := $(BUILD_ROOT_TOP)/tools/Debug/$(TOOLNAME)
	TOOLEXENAME_O := $(BUILD_ROOT_TOP)/tools/Release/$(TOOLNAME)
	TOOLEXENAME_P := $(BUILD_ROOT_TOP)/tools/Profile/$(TOOLNAME)

	ifndef ENABLE_OPTIMIZED
	TOOLEXENAMES := $(TOOLEXENAME_G)
	else
	ifdef ENABLE_PROFILING
	TOOLEXENAMES := $(TOOLEXENAME_P)
	else
	TOOLEXENAMES := $(TOOLEXENAME_O)
	endif
	endif

	# USED_LIBS_OPTIONS - Compute the options line that add -llib1 -llib2, etc.
	USED_LIBS_OPTIONS := $(patsubst %.a.o, -l%, $(addsuffix .o, $(USEDLIBS)))
	USED_LIBS_OPTIONS_G := $(patsubst %.o, $(LIBDEBUG)/%.o, $(USED_LIBS_OPTIONS))
	USED_LIBS_OPTIONS_O := $(patsubst %.o, $(LIBRELEASE)/%.o,$(USED_LIBS_OPTIONS))
	USED_LIBS_OPTIONS_P := $(patsubst %.o, $(LIBPROFILE)/%.o,$(USED_LIBS_OPTIONS))


	# USED_LIB_PATHS - Compute the path of the libraries used so that tools are
	# rebuilt if libraries change. This has to make sure to handle .a/.so and .o
	# files seperately.
	#
	STATICUSEDLIBS := $(patsubst %.a.o, lib%.a, $(addsuffix .o, $(USEDLIBS)))
	USED_LIB_PATHS_G := $(addprefix $(LIBDEBUG)/, $(STATICUSEDLIBS))
	USED_LIB_PATHS_O := $(addprefix $(LIBRELEASE)/, $(STATICUSEDLIBS))
	USED_LIB_PATHS_P := $(addprefix $(LIBPROFILE)/, $(STATICUSEDLIBS))
	LINK_OPTS := $(TOOLLINKOPTS) $(PLATFORMLINKOPTS)


	# Tell make that we need to rebuild subdirectories before we can link the tool.
	# This affects things like LLI which has library subdirectories.
	$(USED_LIB_PATHS_G) $(USED_LIB_PATHS_O) $(USED_LIB_PATHS_P): \
	$(addsuffix /.makeall, $(PARALLEL_DIRS))

	all:: $(TOOLEXENAMES)
	clean::
	$(VERB) rm -f $(TOOLEXENAMES)

	$(TOOLEXENAME_G): $(ObjectsG) $(USED_LIB_PATHS_G) $(TOOLDEBUG)/.dir
	@echo ======= Linking $(TOOLNAME) debug executable $(STRIP_WARN_MSG) =======
	$(VERB) $(LinkG) -o $@ $(ObjectsG) $(USED_LIBS_OPTIONS_G) $(LINK_OPTS)

	$(TOOLEXENAME_O): $(ObjectsO) $(USED_LIB_PATHS_O) $(TOOLRELEASE)/.dir
	@echo ======= Linking $(TOOLNAME) release executable =======
	$(VERB) $(LinkO) -o $@ $(ObjectsO) $(USED_LIBS_OPTIONS_O) $(LINK_OPTS)

	$(TOOLEXENAME_P): $(ObjectsP) $(USED_LIB_PATHS_P) $(TOOLPROFILE)/.dir
	@echo ======= Linking $(TOOLNAME) profile executable =======
	$(VERB) $(LinkP) -o $@ $(ObjectsP) $(USED_LIBS_OPTIONS_P) $(LINK_OPTS)

	endif



	#---------------------------------------------------------
	.PRECIOUS: $(BUILD_ROOT)/Depend/.dir
	.PRECIOUS: $(BUILD_ROOT)/Debug/.dir $(BUILD_ROOT)/Release/.dir

	# Create dependencies for the *.cpp files...
	$(BUILD_ROOT)/Depend/%.d: %.cpp $(BUILD_ROOT)/Depend/.dir
	$(VERB) $(Depend) $< \| sed 's\|$\.o \|$(BUILD_ROOT)/Release/& $(BUILD_ROOT)/Profile/& $(BUILD_ROOT)/Debug/& $(BUILD_ROOT)/Depend/$(@F)\|g' > $@

	# Create dependencies for the *.c files...
	$(BUILD_ROOT)/Depend/%.d: %.c $(BUILD_ROOT)/Depend/.dir
	$(VERB) $(DependC) $< \| sed 's\|$\.o \|Release/& Profile/& Debug/& Depend/$(@F)\|g' > $@

	# Create .o files in the ObjectFiles directory from the .cpp and .c files...
	$(BUILD_ROOT)/Release/%.o: %.cpp $(BUILD_ROOT)/Release/.dir
	@echo "Compiling $<"
	$(VERB) $(CompileO) $< -o $@

	$(BUILD_ROOT)/Release/%.o: %.c $(BUILD_ROOT)/Release/.dir
	$(VERB) $(CompileCO) $< -o $@

	$(BUILD_ROOT)/Profile/%.o: %.cpp $(BUILD_ROOT)/Profile/.dir
	@echo "Compiling $<"
	$(VERB) $(CompileP) $< -o $@

	$(BUILD_ROOT)/Profile/%.o: %.c $(BUILD_ROOT)/Profile/.dir
	@echo "Compiling $<"
	$(VERB) $(CompileCP) $< -o $@

	$(BUILD_ROOT)/Debug/%.o: %.cpp $(BUILD_ROOT)/Debug/.dir
	@echo "Compiling $<"
	$(VERB) $(CompileG) $< -o $@

	$(BUILD_ROOT)/Debug/%.o: %.c $(BUILD_ROOT)/Debug/.dir
	$(VERB) $(CompileCG) $< -o $@

	#
	# Rules for building lex/yacc files
	#
	LEX_FILES = $(filter %.l, $(Source))
	LEX_OUTPUT = $(LEX_FILES:%.l=%.cpp)
	YACC_FILES = $(filter %.y, $(Source))
	YACC_OUTPUT = $(addprefix $(YACC_FILES:%.y=%), .h .cpp .output)
	.PRECIOUS: $(LEX_OUTPUT) $(YACC_OUTPUT)

	# Create a .cpp source file from a flex input file... this uses sed to cut down
	# on the warnings emited by GCC...
	#
	# The last line is a gross hack to work around flex aparently not being able to
	# resize the buffer on a large token input. Currently, for uninitialized string
	# buffers in LLVM we can generate very long tokens, so this is a hack around it.
	# FIXME. (f.e. char Buffer[10000]; )
	#
	%.cpp: %.l
	flex -t $< \| sed '/^find_rule/d' \| \
	sed 's/void yyunput/inline void yyunput/' \| \
	sed 's/void \yy_flex_realloc/inline void yy_flex_realloc/' \| \
	sed 's/#define YY_BUF_SIZE 16384/#define YY_BUF_SIZE (16384*64)/' > $@

	# Rule for building the bison parsers...

	%.cpp %.h : %.y
	$(VERB) $(BISON) -v -d -p $(<:%Parser.y=%) $*.y
	$(VERB) mv -f $.tab.c $.cpp
	$(VERB) mv -f $.tab.h $.h

	# To create the directories...
	%/.dir:
	$(VERB) mkdir -p $*
	@date > $@

	# To create postscript files from dot files...
	%.ps: %.dot
	dot -Tps < $< > $@

	# 'make clean' nukes the tree
	clean::
	$(VERB) rm -rf $(BUILD_ROOT)/Debug $(BUILD_ROOT)/Release $(BUILD_ROOT)/Profile $(BUILD_ROOT)/Depend
	$(VERB) rm -f core core.[0-9][0-9]* .o .d .so ~ *.flc
	$(VERB) rm -f $(LEX_OUTPUT) $(YACC_OUTPUT)

	# If dependancies were generated for the file that included this file,
	# include the dependancies now...
	#
	SourceDepend := $(addsuffix .d,$(addprefix $(BUILD_ROOT)/Depend/,$(basename $(filter-out Debug/%, $(Source)))))
	ifneq ($(SourceDepend),)
	-include $(SourceDepend)
	endif