include/dev/gpio_keypad.h - kernel/lk - Gitiles

 /*
  * Copyright (c) 2008, Google Inc.
  * All rights reserved.
  *
  * Copyright (c) 2009-2011, Code Aurora Forum. All rights reserved.
  *
  * Redistribution and use in source and binary forms, with or without
  * modification, are permitted provided that the following conditions
  * are met:
  *  * Redistributions of source code must retain the above copyright
  *    notice, this list of conditions and the following disclaimer.
  *  * Redistributions in binary form must reproduce the above copyright
  *    notice, this list of conditions and the following disclaimer in
  *    the documentation and/or other materials provided with the
  *    distribution.
  *  * Neither the name of Google, Inc. nor the names of its contributors
  *    may be used to endorse or promote products derived from this
  *    software without specific prior written permission.
  *
  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
  * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
  * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
  * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
  * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
  * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
  * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
  * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
  * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
  * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
  * SUCH DAMAGE.
  */

 #ifndef __DEV_GPIO_KEYPAD_H
 #define __DEV_GPIO_KEYPAD_H

 #include <sys/types.h>

 /* unset: drive active output low, set: drive active output high */
 #define GPIOKPF_ACTIVE_HIGH		(1U << 0)
 #define GPIOKPF_DRIVE_INACTIVE		(1U << 1)

 struct gpio_keypad_info {
 	/* size must be ninputs * noutputs */
 	const uint16_t *keymap;
 	unsigned *input_gpios;
 	unsigned *output_gpios;
 	int ninputs;
 	int noutputs;
 	/* time to wait before reading inputs after driving each output */
 	time_t settle_time;
 	time_t poll_time;
 	unsigned flags;
 };

 void gpio_keypad_init(struct gpio_keypad_info *kpinfo);

 //Macros for SSBI Qwerty keypad for 7x30

 /* SSBI 2.0 controller registers */
 #define MSM_SSBI_BASE                   0xAD900000

 #define SSBI_TIMEOUT_US			100

 #define SSBI2_CTL			0x0000
 #define SSBI2_RESET			0x0004
 #define SSBI2_CMD			0x0008
 #define SSBI2_RD			0x0010
 #define SSBI2_STATUS			0x0014
 #define SSBI2_PRIORITIES		0x0018
 #define SSBI2_MODE2			0x001C

 /* SSBI_CMD fields */
 #define SSBI_CMD_SEND_TERM_SYM		(0x01 << 27)
 #define SSBI_CMD_WAKEUP_SLAVE		(0x01 << 26)
 #define SSBI_CMD_USE_ENABLE		(0x01 << 25)
 #define SSBI_CMD_RDWRN			(0x01 << 24)
 #define SSBI_CMD_REG_ADDR_SHFT		(0x10)
 #define SSBI_CMD_REG_ADDR_MASK		(0xFF << SSBI_CMD_REG_ADDR_SHFT)
 #define SSBI_CMD_REG_DATA_SHFT		(0x00)
 #define SSBI_CMD_REG_DATA_MASK		(0xFF << SSBI_CMD_REG_DATA_SHFT)

 /* SSBI_STATUS fields */
 #define SSBI_STATUS_DATA_IN		0x10
 #define SSBI_STATUS_RD_CLOBBERED	0x08
 #define SSBI_STATUS_RD_READY		0x04
 #define SSBI_STATUS_READY		0x02
 #define SSBI_STATUS_MCHN_BUSY		0x01

 /* SSBI_RD fields */
 #define SSBI_RD_USE_ENABLE		0x02000000
 #define SSBI_RD_RDWRN			0x01000000
 #define SSBI_RD_REG_ADDR_SHFT		0x10
 #define SSBI_RD_REG_ADDR_MASK		(0xFF << SSBI_RD_REG_ADDR_SHFT)
 #define SSBI_RD_REG_DATA_SHFT		(0x00)
 #define SSBI_RD_REG_DATA_MASK		(0xFF << SSBI_RD_REG_DATA_SHFT)

 /* SSBI_MODE2 fields */
 #define SSBI_MODE2_REG_ADDR_15_8_SHFT	0x04
 #define SSBI_MODE2_REG_ADDR_15_8_MASK	(0x7F << SSBI_MODE2_REG_ADDR_15_8_SHFT)
 #define SSBI_MODE2_ADDR_WIDTH_SHFT	0x01
 #define SSBI_MODE2_ADDR_WIDTH_MASK	(0x07 << SSBI_MODE2_ADDR_WIDTH_SHFT)
 #define SSBI_MODE2_SSBI2_MODE		0x00000001

 //Keypad controller configurations
 #define SSBI_REG_KYPD_CNTL_ADDR         0x148
 #define SSBI_REG_KYPD_SCAN_ADDR         0x149
 #define SSBI_REG_KYPD_TEST_ADDR         0x14A
 #define SSBI_REG_KYPD_REC_DATA_ADDR     0x14B
 #define SSBI_REG_KYPD_OLD_DATA_ADDR     0x14C

 // GPIO configurations

 #define	SSBI_REG_ADDR_GPIO_BASE		0x150

 #define QT_PMIC_GPIO_KYPD_SNS           0x008
 #define QT_PMIC_GPIO_KYPD_DRV           0x003

 #define SSBI_OFFSET_ADDR_GPIO_KYPD_SNS  0x000
 #define SSBI_OFFSET_ADDR_GPIO_KYPD_DRV  0x008

 #define	SSBI_REG_ADDR_GPIO(n)		(SSBI_REG_ADDR_GPIO_BASE + n)

 #define	PM_GPIO_DIR_OUT			0x01
 #define	PM_GPIO_DIR_IN			0x02
 #define	PM_GPIO_DIR_BOTH		(PM_GPIO_DIR_OUT | PM_GPIO_DIR_IN)

 #define	PM_GPIO_PULL_UP1		2
 #define	PM_GPIO_PULL_UP2		3
 #define	PM_GPIO_PULL_DN			4
 #define	PM_GPIO_PULL_NO			5

 #define	PM_GPIO_STRENGTH_NO		0
 #define	PM_GPIO_STRENGTH_HIGH		1
 #define	PM_GPIO_STRENGTH_MED		2
 #define	PM_GPIO_STRENGTH_LOW		3

 #define	PM_GPIO_FUNC_NORMAL		0
 #define	PM_GPIO_FUNC_PAIRED		1
 #define	PM_GPIO_FUNC_1			2
 #define	PM_GPIO_FUNC_2			3

 #define	PM8058_GPIO_BANK_MASK		0x70
 #define	PM8058_GPIO_BANK_SHIFT		4
 #define	PM8058_GPIO_WRITE		0x80

 /* Bank 0 */
 #define	PM8058_GPIO_VIN_MASK		0x0E
 #define	PM8058_GPIO_VIN_SHIFT		1
 #define	PM8058_GPIO_MODE_ENABLE		0x01

 /* Bank 1 */
 #define	PM8058_GPIO_MODE_MASK		0x0C
 #define	PM8058_GPIO_MODE_SHIFT		2
 #define	PM8058_GPIO_OUT_BUFFER		0x02
 #define	PM8058_GPIO_OUT_INVERT		0x01

 #define	PM8058_GPIO_MODE_OFF		3
 #define	PM8058_GPIO_MODE_OUTPUT		2
 #define	PM8058_GPIO_MODE_INPUT		0
 #define	PM8058_GPIO_MODE_BOTH		1

 /* Bank 2 */
 #define	PM8058_GPIO_PULL_MASK		0x0E
 #define	PM8058_GPIO_PULL_SHIFT		1

 /* Bank 3 */
 #define	PM8058_GPIO_OUT_STRENGTH_MASK   0x0C
 #define	PM8058_GPIO_OUT_STRENGTH_SHIFT  2

 /* Bank 4 */
 #define	PM8058_GPIO_FUNC_MASK		0x0E
 #define	PM8058_GPIO_FUNC_SHIFT		1


 /* PMIC Arbiter 1: SSBI2 Configuration Micro ARM registers */
 #define PA1_SSBI2_CMD                   0x00500000
 #define PA1_SSBI2_RD_STATUS             0x00500004

 #define PA1_SSBI2_REG_ADDR_SHIFT        8
 #define PA1_SSBI2_CMD_RDWRN_SHIFT       24
 #define PA1_SSBI2_TRANS_DONE_SHIFT      27

 #define PA1_SSBI2_REG_DATA_MASK         0xFF
 #define PA1_SSBI2_REG_DATA_SHIFT        0

 #define PA1_SSBI2_CMD_READ              1
 #define PA1_SSBI2_CMD_WRITE             0

 /* PMIC Arbiter 2: SSBI2 Configuration Micro ARM registers */
 #define PA2_SSBI2_CMD                   0x00C00000
 #define PA2_SSBI2_RD_STATUS             0x00C00004

 #define PA2_SSBI2_REG_ADDR_SHIFT        8
 #define PA2_SSBI2_CMD_RDWRN_SHIFT       24
 #define PA2_SSBI2_TRANS_DONE_SHIFT      27

 #define PA2_SSBI2_REG_DATA_MASK         0xFF
 #define PA2_SSBI2_REG_DATA_SHIFT        0

 #define PA2_SSBI2_CMD_READ              1
 #define PA2_SSBI2_CMD_WRITE             0

 struct pm8058_gpio {
 	int		direction;
 	int		pull;
 	int		vin_sel;	/* 0..7 */
 	int		out_strength;
 	int		function;
 	int		inv_int_pol;	/* invert interrupt polarity */
 };

 bool pm8058_gpio_get(unsigned int gpio);

 typedef int (*read_func)(unsigned char *, unsigned short, unsigned short);
 typedef int (*write_func)(unsigned char *, unsigned short, unsigned short);

 struct qwerty_keypad_info {
 	/* size must be ninputs * noutputs */
 	unsigned int   *keymap;
         unsigned char  *old_keys;
         unsigned char  *rec_keys;
         unsigned int   rows;
         unsigned int   columns;
         unsigned int   num_of_reads;
         read_func      rd_func;
         write_func     wr_func;
 	/* time to wait before reading inputs after driving each output */
 	time_t         settle_time;
 	time_t         poll_time;
 	unsigned       flags;
 };

 #define SSBI_CMD_READ(AD) \
 	(SSBI_CMD_RDWRN | (((AD) & 0xFF) << SSBI_CMD_REG_ADDR_SHFT))

 #define SSBI_CMD_WRITE(AD, DT) \
   ((((AD) & 0xFF) << SSBI_CMD_REG_ADDR_SHFT) | \
    (((DT) & 0xFF) << SSBI_CMD_REG_DATA_SHFT))

 #define SSBI_MODE2_REG_ADDR_15_8(MD, AD) \
 	(((MD) & 0x0F) | ((((AD) >> 8) << SSBI_MODE2_REG_ADDR_15_8_SHFT) & \
 	SSBI_MODE2_REG_ADDR_15_8_MASK))

 void ssbi_keypad_init (struct qwerty_keypad_info *);
 int i2c_ssbi_read_bytes(unsigned char  *buffer, unsigned short length,
 			unsigned short slave_addr);
 int i2c_ssbi_write_bytes(unsigned char  *buffer, unsigned short length,
 			 unsigned short slave_addr);
 int pa1_ssbi2_read_bytes(unsigned char  *buffer, unsigned short length,
 			 unsigned short slave_addr);
 int pa1_ssbi2_write_bytes(unsigned char  *buffer, unsigned short length,
 			  unsigned short slave_addr);

 #endif /* __DEV_GPIO_KEYPAD_H */
	/*
	* Copyright (c) 2008, Google Inc.
	* All rights reserved.
	*
	* Copyright (c) 2009-2011, Code Aurora Forum. All rights reserved.
	*
	* Redistribution and use in source and binary forms, with or without
	* modification, are permitted provided that the following conditions
	* are met:
	* * Redistributions of source code must retain the above copyright
	* notice, this list of conditions and the following disclaimer.
	* * Redistributions in binary form must reproduce the above copyright
	* notice, this list of conditions and the following disclaimer in
	* the documentation and/or other materials provided with the
	* distribution.
	* * Neither the name of Google, Inc. nor the names of its contributors
	* may be used to endorse or promote products derived from this
	* software without specific prior written permission.
	*
	* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
	* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
	* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
	* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
	* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
	* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
	* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
	* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
	* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
	* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
	* OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
	* SUCH DAMAGE.
	*/

	#ifndef __DEV_GPIO_KEYPAD_H
	#define __DEV_GPIO_KEYPAD_H

	#include <sys/types.h>

	/* unset: drive active output low, set: drive active output high */
	#define GPIOKPF_ACTIVE_HIGH (1U << 0)
	#define GPIOKPF_DRIVE_INACTIVE (1U << 1)

	struct gpio_keypad_info {
	/* size must be ninputs * noutputs */
	const uint16_t *keymap;
	unsigned *input_gpios;
	unsigned *output_gpios;
	int ninputs;
	int noutputs;
	/* time to wait before reading inputs after driving each output */
	time_t settle_time;
	time_t poll_time;
	unsigned flags;
	};

	void gpio_keypad_init(struct gpio_keypad_info *kpinfo);

	//Macros for SSBI Qwerty keypad for 7x30

	/* SSBI 2.0 controller registers */
	#define MSM_SSBI_BASE 0xAD900000

	#define SSBI_TIMEOUT_US 100

	#define SSBI2_CTL 0x0000
	#define SSBI2_RESET 0x0004
	#define SSBI2_CMD 0x0008
	#define SSBI2_RD 0x0010
	#define SSBI2_STATUS 0x0014
	#define SSBI2_PRIORITIES 0x0018
	#define SSBI2_MODE2 0x001C

	/* SSBI_CMD fields */
	#define SSBI_CMD_SEND_TERM_SYM (0x01 << 27)
	#define SSBI_CMD_WAKEUP_SLAVE (0x01 << 26)
	#define SSBI_CMD_USE_ENABLE (0x01 << 25)
	#define SSBI_CMD_RDWRN (0x01 << 24)
	#define SSBI_CMD_REG_ADDR_SHFT (0x10)
	#define SSBI_CMD_REG_ADDR_MASK (0xFF << SSBI_CMD_REG_ADDR_SHFT)
	#define SSBI_CMD_REG_DATA_SHFT (0x00)
	#define SSBI_CMD_REG_DATA_MASK (0xFF << SSBI_CMD_REG_DATA_SHFT)

	/* SSBI_STATUS fields */
	#define SSBI_STATUS_DATA_IN 0x10
	#define SSBI_STATUS_RD_CLOBBERED 0x08
	#define SSBI_STATUS_RD_READY 0x04
	#define SSBI_STATUS_READY 0x02
	#define SSBI_STATUS_MCHN_BUSY 0x01

	/* SSBI_RD fields */
	#define SSBI_RD_USE_ENABLE 0x02000000
	#define SSBI_RD_RDWRN 0x01000000
	#define SSBI_RD_REG_ADDR_SHFT 0x10
	#define SSBI_RD_REG_ADDR_MASK (0xFF << SSBI_RD_REG_ADDR_SHFT)
	#define SSBI_RD_REG_DATA_SHFT (0x00)
	#define SSBI_RD_REG_DATA_MASK (0xFF << SSBI_RD_REG_DATA_SHFT)

	/* SSBI_MODE2 fields */
	#define SSBI_MODE2_REG_ADDR_15_8_SHFT 0x04
	#define SSBI_MODE2_REG_ADDR_15_8_MASK (0x7F << SSBI_MODE2_REG_ADDR_15_8_SHFT)
	#define SSBI_MODE2_ADDR_WIDTH_SHFT 0x01
	#define SSBI_MODE2_ADDR_WIDTH_MASK (0x07 << SSBI_MODE2_ADDR_WIDTH_SHFT)
	#define SSBI_MODE2_SSBI2_MODE 0x00000001

	//Keypad controller configurations
	#define SSBI_REG_KYPD_CNTL_ADDR 0x148
	#define SSBI_REG_KYPD_SCAN_ADDR 0x149
	#define SSBI_REG_KYPD_TEST_ADDR 0x14A
	#define SSBI_REG_KYPD_REC_DATA_ADDR 0x14B
	#define SSBI_REG_KYPD_OLD_DATA_ADDR 0x14C

	// GPIO configurations

	#define SSBI_REG_ADDR_GPIO_BASE 0x150

	#define QT_PMIC_GPIO_KYPD_SNS 0x008
	#define QT_PMIC_GPIO_KYPD_DRV 0x003

	#define SSBI_OFFSET_ADDR_GPIO_KYPD_SNS 0x000
	#define SSBI_OFFSET_ADDR_GPIO_KYPD_DRV 0x008

	#define SSBI_REG_ADDR_GPIO(n) (SSBI_REG_ADDR_GPIO_BASE + n)

	#define PM_GPIO_DIR_OUT 0x01
	#define PM_GPIO_DIR_IN 0x02
	#define PM_GPIO_DIR_BOTH (PM_GPIO_DIR_OUT \| PM_GPIO_DIR_IN)

	#define PM_GPIO_PULL_UP1 2
	#define PM_GPIO_PULL_UP2 3
	#define PM_GPIO_PULL_DN 4
	#define PM_GPIO_PULL_NO 5

	#define PM_GPIO_STRENGTH_NO 0
	#define PM_GPIO_STRENGTH_HIGH 1
	#define PM_GPIO_STRENGTH_MED 2
	#define PM_GPIO_STRENGTH_LOW 3

	#define PM_GPIO_FUNC_NORMAL 0
	#define PM_GPIO_FUNC_PAIRED 1
	#define PM_GPIO_FUNC_1 2
	#define PM_GPIO_FUNC_2 3

	#define PM8058_GPIO_BANK_MASK 0x70
	#define PM8058_GPIO_BANK_SHIFT 4
	#define PM8058_GPIO_WRITE 0x80

	/* Bank 0 */
	#define PM8058_GPIO_VIN_MASK 0x0E
	#define PM8058_GPIO_VIN_SHIFT 1
	#define PM8058_GPIO_MODE_ENABLE 0x01

	/* Bank 1 */
	#define PM8058_GPIO_MODE_MASK 0x0C
	#define PM8058_GPIO_MODE_SHIFT 2
	#define PM8058_GPIO_OUT_BUFFER 0x02
	#define PM8058_GPIO_OUT_INVERT 0x01

	#define PM8058_GPIO_MODE_OFF 3
	#define PM8058_GPIO_MODE_OUTPUT 2
	#define PM8058_GPIO_MODE_INPUT 0
	#define PM8058_GPIO_MODE_BOTH 1

	/* Bank 2 */
	#define PM8058_GPIO_PULL_MASK 0x0E
	#define PM8058_GPIO_PULL_SHIFT 1

	/* Bank 3 */
	#define PM8058_GPIO_OUT_STRENGTH_MASK 0x0C
	#define PM8058_GPIO_OUT_STRENGTH_SHIFT 2

	/* Bank 4 */
	#define PM8058_GPIO_FUNC_MASK 0x0E
	#define PM8058_GPIO_FUNC_SHIFT 1


	/* PMIC Arbiter 1: SSBI2 Configuration Micro ARM registers */
	#define PA1_SSBI2_CMD 0x00500000
	#define PA1_SSBI2_RD_STATUS 0x00500004

	#define PA1_SSBI2_REG_ADDR_SHIFT 8
	#define PA1_SSBI2_CMD_RDWRN_SHIFT 24
	#define PA1_SSBI2_TRANS_DONE_SHIFT 27

	#define PA1_SSBI2_REG_DATA_MASK 0xFF
	#define PA1_SSBI2_REG_DATA_SHIFT 0

	#define PA1_SSBI2_CMD_READ 1
	#define PA1_SSBI2_CMD_WRITE 0

	/* PMIC Arbiter 2: SSBI2 Configuration Micro ARM registers */
	#define PA2_SSBI2_CMD 0x00C00000
	#define PA2_SSBI2_RD_STATUS 0x00C00004

	#define PA2_SSBI2_REG_ADDR_SHIFT 8
	#define PA2_SSBI2_CMD_RDWRN_SHIFT 24
	#define PA2_SSBI2_TRANS_DONE_SHIFT 27

	#define PA2_SSBI2_REG_DATA_MASK 0xFF
	#define PA2_SSBI2_REG_DATA_SHIFT 0

	#define PA2_SSBI2_CMD_READ 1
	#define PA2_SSBI2_CMD_WRITE 0

	struct pm8058_gpio {
	int direction;
	int pull;
	int vin_sel; /* 0..7 */
	int out_strength;
	int function;
	int inv_int_pol; /* invert interrupt polarity */
	};

	bool pm8058_gpio_get(unsigned int gpio);

	typedef int (read_func)(unsigned char , unsigned short, unsigned short);
	typedef int (write_func)(unsigned char , unsigned short, unsigned short);

	struct qwerty_keypad_info {
	/* size must be ninputs * noutputs */
	unsigned int *keymap;
	unsigned char *old_keys;
	unsigned char *rec_keys;
	unsigned int rows;
	unsigned int columns;
	unsigned int num_of_reads;
	read_func rd_func;
	write_func wr_func;
	/* time to wait before reading inputs after driving each output */
	time_t settle_time;
	time_t poll_time;
	unsigned flags;
	};

	#define SSBI_CMD_READ(AD) \
	(SSBI_CMD_RDWRN \| (((AD) & 0xFF) << SSBI_CMD_REG_ADDR_SHFT))

	#define SSBI_CMD_WRITE(AD, DT) \
	((((AD) & 0xFF) << SSBI_CMD_REG_ADDR_SHFT) \| \
	(((DT) & 0xFF) << SSBI_CMD_REG_DATA_SHFT))

	#define SSBI_MODE2_REG_ADDR_15_8(MD, AD) \
	(((MD) & 0x0F) \| ((((AD) >> 8) << SSBI_MODE2_REG_ADDR_15_8_SHFT) & \
	SSBI_MODE2_REG_ADDR_15_8_MASK))

	void ssbi_keypad_init (struct qwerty_keypad_info *);
	int i2c_ssbi_read_bytes(unsigned char *buffer, unsigned short length,
	unsigned short slave_addr);
	int i2c_ssbi_write_bytes(unsigned char *buffer, unsigned short length,
	unsigned short slave_addr);
	int pa1_ssbi2_read_bytes(unsigned char *buffer, unsigned short length,
	unsigned short slave_addr);
	int pa1_ssbi2_write_bytes(unsigned char *buffer, unsigned short length,
	unsigned short slave_addr);

	#endif /* __DEV_GPIO_KEYPAD_H */