| /* Copyright (c) 2010, Code Aurora Forum. All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions are |
| * met: |
| * * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * * Redistributions in binary form must reproduce the above |
| * copyright notice, this list of conditions and the following |
| * disclaimer in the documentation and/or other materials provided |
| * with the distribution. |
| * * Neither the name of Code Aurora Forum, Inc. nor the names of its |
| * contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED |
| * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT |
| * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS |
| * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR |
| * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF |
| * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR |
| * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, |
| * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE |
| * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN |
| * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| /* |
| * QUP driver for Qualcomm MSM platforms |
| * |
| */ |
| |
| #include <debug.h> |
| #include <arch/arm.h> |
| #include <reg.h> |
| #include <kernel/thread.h> |
| #include <dev/gpio.h> |
| #include <stdlib.h> |
| #include <string.h> |
| |
| #include <gsbi.h> |
| #include <i2c_qup.h> |
| #include <platform/irqs.h> |
| #include <platform/iomap.h> |
| #include <platform/gpio.h> |
| #include <platform/clock.h> |
| #include <platform/timer.h> |
| #include <platform/interrupts.h> |
| |
| |
| static struct qup_i2c_dev *dev_addr = NULL; |
| |
| /* QUP Registers */ |
| enum { |
| QUP_CONFIG = 0x0, |
| QUP_STATE = 0x4, |
| QUP_IO_MODE = 0x8, |
| QUP_SW_RESET = 0xC, |
| QUP_OPERATIONAL = 0x18, |
| QUP_ERROR_FLAGS = 0x1C, |
| QUP_ERROR_FLAGS_EN = 0x20, |
| QUP_MX_READ_CNT = 0x208, |
| QUP_MX_INPUT_CNT = 0x200, |
| QUP_MX_WR_CNT = 0x100, |
| QUP_OUT_DEBUG = 0x108, |
| QUP_OUT_FIFO_CNT = 0x10C, |
| QUP_OUT_FIFO_BASE = 0x110, |
| QUP_IN_READ_CUR = 0x20C, |
| QUP_IN_DEBUG = 0x210, |
| QUP_IN_FIFO_CNT = 0x214, |
| QUP_IN_FIFO_BASE = 0x218, |
| QUP_I2C_CLK_CTL = 0x400, |
| QUP_I2C_STATUS = 0x404, |
| }; |
| |
| /* QUP States and reset values */ |
| enum { |
| QUP_RESET_STATE = 0, |
| QUP_RUN_STATE = 1U, |
| QUP_STATE_MASK = 3U, |
| QUP_PAUSE_STATE = 3U, |
| QUP_STATE_VALID = 1U << 2, |
| QUP_I2C_MAST_GEN = 1U << 4, |
| QUP_OPERATIONAL_RESET = 0xFF0, |
| QUP_I2C_STATUS_RESET = 0xFFFFFC, |
| }; |
| |
| /* QUP OPERATIONAL FLAGS */ |
| enum { |
| QUP_OUT_SVC_FLAG = 1U << 8, |
| QUP_IN_SVC_FLAG = 1U << 9, |
| QUP_MX_INPUT_DONE = 1U << 11, |
| }; |
| |
| /* I2C mini core related values */ |
| enum { |
| I2C_MINI_CORE = 2U << 8, |
| I2C_N_VAL = 0xF, |
| |
| }; |
| |
| /* Packing Unpacking words in FIFOs , and IO modes*/ |
| enum { |
| QUP_WR_BLK_MODE = 1U << 10, |
| QUP_RD_BLK_MODE = 1U << 12, |
| QUP_UNPACK_EN = 1U << 14, |
| QUP_PACK_EN = 1U << 15, |
| }; |
| |
| /* QUP tags */ |
| enum { |
| QUP_OUT_NOP = 0, |
| QUP_OUT_START = 1U << 8, |
| QUP_OUT_DATA = 2U << 8, |
| QUP_OUT_STOP = 3U << 8, |
| QUP_OUT_REC = 4U << 8, |
| QUP_IN_DATA = 5U << 8, |
| QUP_IN_STOP = 6U << 8, |
| QUP_IN_NACK = 7U << 8, |
| }; |
| |
| /* Status, Error flags */ |
| enum { |
| I2C_STATUS_WR_BUFFER_FULL = 1U << 0, |
| I2C_STATUS_BUS_ACTIVE = 1U << 8, |
| I2C_STATUS_ERROR_MASK = 0x38000FC, |
| QUP_I2C_NACK_FLAG = 1U << 3, |
| QUP_IN_NOT_EMPTY = 1U << 5, |
| QUP_STATUS_ERROR_FLAGS = 0x7C, |
| }; |
| |
| #ifdef DEBUG_QUP |
| static void qup_print_status(struct qup_i2c_dev *dev) |
| { |
| unsigned val; |
| val = readl(dev->qup_base + QUP_CONFIG); |
| dprintf(INFO, "Qup config is :0x%x\n", val); |
| val = readl(dev->qup_base + QUP_STATE); |
| dprintf(INFO, "Qup state is :0x%x\n", val); |
| val = readl(dev->qup_base + QUP_IO_MODE); |
| dprintf(INFO, "Qup mode is :0x%x\n", val); |
| } |
| #else |
| static inline void qup_print_status(struct qup_i2c_dev *dev) |
| { |
| } |
| #endif |
| |
| static irqreturn_t qup_i2c_interrupt(void) |
| { |
| struct qup_i2c_dev *dev = dev_addr; |
| if (!dev) { |
| dprintf(CRITICAL, |
| "dev_addr is NULL, that means i2c_qup_init failed...\n"); |
| return IRQ_FAIL; |
| } |
| unsigned status = readl(dev->qup_base + QUP_I2C_STATUS); |
| unsigned status1 = readl(dev->qup_base + QUP_ERROR_FLAGS); |
| unsigned op_flgs = readl(dev->qup_base + QUP_OPERATIONAL); |
| int err = 0; |
| |
| if (!dev->msg) |
| return IRQ_HANDLED; |
| |
| if (status & I2C_STATUS_ERROR_MASK) { |
| dprintf(CRITICAL, "QUP: I2C status flags :0x%x \n", status); |
| err = -status; |
| /* Clear Error interrupt if it's a level triggered interrupt */ |
| if (dev->num_irqs == 1) { |
| writel(QUP_RESET_STATE, dev->qup_base + QUP_STATE); |
| } |
| goto intr_done; |
| } |
| |
| if (status1 & 0x7F) { |
| dprintf(CRITICAL, "QUP: QUP status flags :0x%x\n", status1); |
| err = -status1; |
| /* Clear Error interrupt if it's a level triggered interrupt */ |
| if (dev->num_irqs == 1) |
| writel((status1 & QUP_STATUS_ERROR_FLAGS), |
| dev->qup_base + QUP_ERROR_FLAGS); |
| goto intr_done; |
| } |
| |
| if (op_flgs & QUP_OUT_SVC_FLAG) |
| writel(QUP_OUT_SVC_FLAG, dev->qup_base + QUP_OPERATIONAL); |
| if (dev->msg->flags == I2C_M_RD) { |
| if ((op_flgs & QUP_MX_INPUT_DONE) || (op_flgs & QUP_IN_SVC_FLAG)) |
| writel(QUP_IN_SVC_FLAG, dev->qup_base + QUP_OPERATIONAL); |
| else |
| return IRQ_HANDLED; |
| } |
| |
| intr_done: |
| dev->err = err; |
| return IRQ_HANDLED; |
| } |
| |
| static int qup_i2c_poll_writeready(struct qup_i2c_dev *dev) |
| { |
| unsigned retries = 0; |
| |
| while (retries != 2000) { |
| unsigned status = readl(dev->qup_base + QUP_I2C_STATUS); |
| |
| if (!(status & I2C_STATUS_WR_BUFFER_FULL)) { |
| if (!(status & I2C_STATUS_BUS_ACTIVE)) |
| return 0; |
| else /* 1-bit delay before we check for bus busy */ |
| udelay(dev->one_bit_t); |
| } |
| if (retries++ == 1000) |
| udelay(100); |
| } |
| qup_print_status(dev); |
| return -ETIMEDOUT; |
| } |
| |
| static int qup_i2c_poll_state(struct qup_i2c_dev *dev, unsigned state) |
| { |
| unsigned retries = 0; |
| |
| dprintf(INFO, "Polling Status for state:0x%x\n", state); |
| |
| while (retries != 2000) { |
| unsigned status = readl(dev->qup_base + QUP_STATE); |
| |
| if ((status & (QUP_STATE_VALID | state)) == (QUP_STATE_VALID | state)) |
| return 0; |
| else if (retries++ == 1000) |
| udelay(100); |
| } |
| return -ETIMEDOUT; |
| } |
| |
| #ifdef DEBUG |
| static void qup_verify_fifo(struct qup_i2c_dev *dev, unsigned val, |
| unsigned addr, int rdwr) |
| { |
| if (rdwr) |
| dprintf(INFO, "RD:Wrote 0x%x to out_ff:0x%x\n", val, addr); |
| else |
| dprintf(INFO, "WR:Wrote 0x%x to out_ff:0x%x\n", val, addr); |
| } |
| #else |
| static inline void qup_verify_fifo(struct qup_i2c_dev *dev, unsigned val, |
| unsigned addr, int rdwr) |
| { |
| } |
| #endif |
| |
| static void |
| qup_issue_read(struct qup_i2c_dev *dev, struct i2c_msg *msg, int *idx, |
| unsigned carry_over) |
| { |
| uint16_t addr = (msg->addr << 1) | 1; |
| /* QUP limit 256 bytes per read. By HW design, 0 in the 8-bit field is |
| treated as 256 byte read. */ |
| uint16_t rd_len = ((dev->cnt == 256) ? 0 : dev->cnt); |
| |
| if (*idx % 4) { |
| writel(carry_over | ((QUP_OUT_START | addr) << 16), |
| dev->qup_base + QUP_OUT_FIFO_BASE); |
| |
| qup_verify_fifo(dev, carry_over | |
| ((QUP_OUT_START | addr) << 16), (unsigned)dev->qup_base |
| + QUP_OUT_FIFO_BASE + (*idx - 2), 1); |
| writel((QUP_OUT_REC | rd_len), dev->qup_base + QUP_OUT_FIFO_BASE); |
| |
| qup_verify_fifo(dev, (QUP_OUT_REC | rd_len), |
| (unsigned)dev->qup_base + QUP_OUT_FIFO_BASE + (*idx + 2), |
| 1); |
| } else { |
| writel(((QUP_OUT_REC | rd_len) << 16) | |
| QUP_OUT_START | addr, dev->qup_base + QUP_OUT_FIFO_BASE); |
| |
| qup_verify_fifo(dev, QUP_OUT_REC << 16 | rd_len << 16 | |
| QUP_OUT_START | addr, |
| (unsigned)dev->qup_base + QUP_OUT_FIFO_BASE + (*idx), 1); |
| } |
| *idx += 4; |
| } |
| |
| static void |
| qup_issue_write(struct qup_i2c_dev *dev, struct i2c_msg *msg, int rem, |
| int *idx, unsigned *carry_over) |
| { |
| int entries = dev->cnt; |
| int empty_sl = dev->wr_sz - ((*idx) >> 1); |
| int i = 0; |
| unsigned val = 0; |
| unsigned last_entry = 0; |
| uint16_t addr = msg->addr << 1; |
| |
| if (dev->pos == 0) { |
| if (*idx % 4) { |
| writel(*carry_over | ((QUP_OUT_START | addr) << 16), |
| dev->qup_base + QUP_OUT_FIFO_BASE); |
| |
| qup_verify_fifo(dev, *carry_over | QUP_OUT_DATA << 16 | |
| addr << 16, (unsigned)dev->qup_base + |
| QUP_OUT_FIFO_BASE + (*idx) - 2, 0); |
| } else |
| val = QUP_OUT_START | addr; |
| *idx += 2; |
| i++; |
| entries++; |
| } else { |
| /* Avoid setp time issue by adding 1 NOP when number of bytes are more |
| than FIFO/BLOCK size. setup time issue can't appear otherwise since |
| next byte to be written will always be ready */ |
| val = (QUP_OUT_NOP | 1); |
| *idx += 2; |
| i++; |
| entries++; |
| } |
| if (entries > empty_sl) |
| entries = empty_sl; |
| |
| for (; i < (entries - 1); i++) { |
| if (*idx % 4) { |
| writel(val | ((QUP_OUT_DATA | |
| msg->buf[dev->pos]) << 16), |
| dev->qup_base + QUP_OUT_FIFO_BASE); |
| |
| qup_verify_fifo(dev, val | QUP_OUT_DATA << 16 | |
| msg->buf[dev->pos] << 16, (unsigned)dev->qup_base + |
| QUP_OUT_FIFO_BASE + (*idx) - 2, 0); |
| } else |
| val = QUP_OUT_DATA | msg->buf[dev->pos]; |
| (*idx) += 2; |
| dev->pos++; |
| } |
| if (dev->pos < (msg->len - 1)) |
| last_entry = QUP_OUT_DATA; |
| else if (rem > 1) /* not last array entry */ |
| last_entry = QUP_OUT_DATA; |
| else |
| last_entry = QUP_OUT_STOP; |
| if ((*idx % 4) == 0) { |
| /* |
| * If read-start and read-command end up in different fifos, it |
| * may result in extra-byte being read due to extra-read cycle. |
| * Avoid that by inserting NOP as the last entry of fifo only |
| * if write command(s) leave 1 space in fifo. |
| */ |
| if (rem > 1) { |
| struct i2c_msg *next = msg + 1; |
| if (next->addr == msg->addr && (next->flags | I2C_M_RD) |
| && *idx == ((dev->wr_sz * 2) - 4)) { |
| writel(((last_entry | msg->buf[dev->pos]) | |
| ((1 | QUP_OUT_NOP) << 16)), |
| dev->qup_base + QUP_OUT_FIFO_BASE); |
| *idx += 2; |
| } else |
| *carry_over = (last_entry | msg->buf[dev->pos]); |
| } else { |
| writel((last_entry | msg->buf[dev->pos]), |
| dev->qup_base + QUP_OUT_FIFO_BASE); |
| |
| qup_verify_fifo(dev, last_entry | msg->buf[dev->pos], |
| (unsigned)dev->qup_base + QUP_OUT_FIFO_BASE + |
| (*idx), 0); |
| } |
| } else { |
| writel(val | ((last_entry | msg->buf[dev->pos]) << 16), |
| dev->qup_base + QUP_OUT_FIFO_BASE); |
| |
| qup_verify_fifo(dev, val | (last_entry << 16) | |
| (msg->buf[dev->pos] << 16), (unsigned)dev->qup_base + |
| QUP_OUT_FIFO_BASE + (*idx) - 2, 0); |
| } |
| |
| *idx += 2; |
| dev->pos++; |
| dev->cnt = msg->len - dev->pos; |
| } |
| |
| static int qup_update_state(struct qup_i2c_dev *dev, unsigned state) |
| { |
| if (qup_i2c_poll_state(dev, 0) != 0) |
| return -EIO; |
| writel(state, dev->qup_base + QUP_STATE); |
| if (qup_i2c_poll_state(dev, state) != 0) |
| return -EIO; |
| return 0; |
| } |
| |
| static int qup_set_read_mode(struct qup_i2c_dev *dev, int rd_len) |
| { |
| unsigned wr_mode = (dev->wr_sz < dev->out_fifo_sz) ? QUP_WR_BLK_MODE : 0; |
| if (rd_len > 256) { |
| dprintf(INFO, "HW doesn't support READs > 256 bytes\n"); |
| return -EPROTONOSUPPORT; |
| } |
| if (rd_len <= dev->in_fifo_sz) { |
| writel(wr_mode | QUP_PACK_EN | QUP_UNPACK_EN, dev->qup_base + QUP_IO_MODE); |
| writel(rd_len, dev->qup_base + QUP_MX_READ_CNT); |
| } else { |
| writel(wr_mode | QUP_RD_BLK_MODE | |
| QUP_PACK_EN | QUP_UNPACK_EN, dev->qup_base + QUP_IO_MODE); |
| writel(rd_len, dev->qup_base + QUP_MX_INPUT_CNT); |
| } |
| return 0; |
| } |
| |
| static int qup_set_wr_mode(struct qup_i2c_dev *dev, int rem) |
| { |
| int total_len = 0; |
| int ret = 0; |
| if (dev->msg->len >= (dev->out_fifo_sz - 1)) { |
| total_len = dev->msg->len + 1 + (dev->msg->len / (dev->out_blk_sz - 1)); |
| writel(QUP_WR_BLK_MODE | QUP_PACK_EN | QUP_UNPACK_EN, |
| dev->qup_base + QUP_IO_MODE); |
| dev->wr_sz = dev->out_blk_sz; |
| } else |
| writel(QUP_PACK_EN | QUP_UNPACK_EN, dev->qup_base + QUP_IO_MODE); |
| |
| if (rem > 1) { |
| struct i2c_msg *next = dev->msg + 1; |
| if (next->addr == dev->msg->addr && next->flags == I2C_M_RD) { |
| ret = qup_set_read_mode(dev, next->len); |
| /* make sure read start & read command are in 1 blk */ |
| if ((total_len % dev->out_blk_sz) == (dev->out_blk_sz - 1)) |
| total_len += 3; |
| else |
| total_len += 2; |
| } |
| } |
| /* WRITE COUNT register valid/used only in block mode */ |
| if (dev->wr_sz == dev->out_blk_sz) |
| writel(total_len, dev->qup_base + QUP_MX_WR_CNT); |
| return ret; |
| } |
| |
| int qup_i2c_xfer(struct qup_i2c_dev *dev, struct i2c_msg msgs[], int num) |
| { |
| int ret; |
| int rem = num; |
| int err; |
| |
| if (dev->suspended) { |
| return -EIO; |
| } |
| |
| /* Set the GSBIn_QUP_APPS_CLK to 24MHz, then below figure out what speed to |
| run I2C_MASTER_CORE at. */ |
| if (dev->clk_state == 0) { |
| if (dev->clk_ctl == 0) { |
| clock_config_i2c(dev->gsbi_number, dev->src_clk_freq); |
| } |
| } |
| /* Initialize QUP registers during first transfer */ |
| if (dev->clk_ctl == 0) { |
| int fs_div; |
| int hs_div; |
| unsigned fifo_reg; |
| /* Configure the GSBI Protocol Code for i2c */ |
| writel((GSBI_PROTOCOL_CODE_I2C << |
| GSBI_CTRL_REG_PROTOCOL_CODE_S), GSBI_CTRL_REG(dev->gsbi_base)); |
| |
| fs_div = ((dev->src_clk_freq / dev->clk_freq) / 2) - 3; |
| hs_div = 3; |
| dev->clk_ctl = ((hs_div & 0x7) << 8) | (fs_div & 0xff); |
| fifo_reg = readl(dev->qup_base + QUP_IO_MODE); |
| if (fifo_reg & 0x3) |
| dev->out_blk_sz = (fifo_reg & 0x3) * 16; |
| else |
| dev->out_blk_sz = 16; |
| if (fifo_reg & 0x60) |
| dev->in_blk_sz = ((fifo_reg & 0x60) >> 5) * 16; |
| else |
| dev->in_blk_sz = 16; |
| /* |
| * The block/fifo size w.r.t. 'actual data' is 1/2 due to 'tag' |
| * associated with each byte written/received |
| */ |
| dev->out_blk_sz /= 2; |
| dev->in_blk_sz /= 2; |
| dev->out_fifo_sz = dev->out_blk_sz * (2 << ((fifo_reg & 0x1C) >> 2)); |
| dev->in_fifo_sz = dev->in_blk_sz * (2 << ((fifo_reg & 0x380) >> 7)); |
| dprintf(INFO, "QUP IN:bl:%d, ff:%d, OUT:bl:%d, ff:%d\n", |
| dev->in_blk_sz, dev->in_fifo_sz, |
| dev->out_blk_sz, dev->out_fifo_sz); |
| } |
| |
| unmask_interrupt(dev->qup_irq); |
| writel(1, dev->qup_base + QUP_SW_RESET); |
| ret = qup_i2c_poll_state(dev, QUP_RESET_STATE); |
| if (ret) { |
| dprintf(INFO, "QUP Busy:Trying to recover\n"); |
| goto out_err; |
| } |
| |
| /* Initialize QUP registers */ |
| writel(0, dev->qup_base + QUP_CONFIG); |
| writel(QUP_OPERATIONAL_RESET, dev->qup_base + QUP_OPERATIONAL); |
| writel(QUP_STATUS_ERROR_FLAGS, dev->qup_base + QUP_ERROR_FLAGS_EN); |
| |
| writel(I2C_MINI_CORE | I2C_N_VAL, dev->qup_base + QUP_CONFIG); |
| |
| /* Initialize I2C mini core registers */ |
| writel(0, dev->qup_base + QUP_I2C_CLK_CTL); |
| writel(QUP_I2C_STATUS_RESET, dev->qup_base + QUP_I2C_STATUS); |
| |
| dev->cnt = msgs->len; |
| dev->pos = 0; |
| dev->msg = msgs; |
| while (rem) { |
| int filled = FALSE; |
| |
| dev->wr_sz = dev->out_fifo_sz; |
| dev->err = 0; |
| |
| if (qup_i2c_poll_state(dev, QUP_I2C_MAST_GEN) != 0) { |
| ret = -EIO; |
| goto out_err; |
| } |
| |
| qup_print_status(dev); |
| /* HW limits Read upto 256 bytes in 1 read without stop */ |
| if (dev->msg->flags & I2C_M_RD) { |
| ret = qup_set_read_mode(dev, dev->cnt); |
| if (ret != 0) |
| goto out_err; |
| } else { |
| ret = qup_set_wr_mode(dev, rem); |
| if (ret != 0) |
| goto out_err; |
| /* Don't fill block till we get interrupt */ |
| if (dev->wr_sz == dev->out_blk_sz) |
| filled = TRUE; |
| } |
| |
| err = qup_update_state(dev, QUP_RUN_STATE); |
| if (err < 0) { |
| ret = err; |
| goto out_err; |
| } |
| |
| qup_print_status(dev); |
| writel(dev->clk_ctl, dev->qup_base + QUP_I2C_CLK_CTL); |
| |
| do { |
| int idx = 0; |
| unsigned carry_over = 0; |
| |
| /* Transition to PAUSE state only possible from RUN */ |
| err = qup_update_state(dev, QUP_PAUSE_STATE); |
| if (err < 0) { |
| ret = err; |
| goto out_err; |
| } |
| |
| qup_print_status(dev); |
| /* This operation is Write, check the next operation and decide |
| mode */ |
| while (filled == FALSE) { |
| if ((msgs->flags & I2C_M_RD) && (dev->cnt == msgs->len)) |
| qup_issue_read(dev, msgs, &idx, carry_over); |
| else if (!(msgs->flags & I2C_M_RD)) |
| qup_issue_write(dev, msgs, rem, &idx, &carry_over); |
| if (idx >= (dev->wr_sz << 1)) |
| filled = TRUE; |
| /* Start new message */ |
| if (filled == FALSE) { |
| if (msgs->flags & I2C_M_RD) |
| filled = TRUE; |
| else if (rem > 1) { |
| /* Only combine operations with same address */ |
| struct i2c_msg *next = msgs + 1; |
| if (next->addr != msgs->addr || next->flags == 0) |
| filled = TRUE; |
| else { |
| rem--; |
| msgs++; |
| dev->msg = msgs; |
| dev->pos = 0; |
| dev->cnt = msgs->len; |
| } |
| } else |
| filled = TRUE; |
| } |
| } |
| err = qup_update_state(dev, QUP_RUN_STATE); |
| if (err < 0) { |
| ret = err; |
| goto out_err; |
| } |
| dprintf(INFO, "idx:%d, rem:%d, num:%d, mode:%d\n", |
| idx, rem, num, dev->mode); |
| |
| qup_print_status(dev); |
| if (dev->err) { |
| if (dev->err & QUP_I2C_NACK_FLAG) { |
| dprintf(CRITICAL, |
| "I2C slave addr:0x%x not connected\n", |
| dev->msg->addr); |
| } else { |
| dprintf(INFO, "QUP data xfer error %d\n", dev->err); |
| } |
| ret = dev->err; |
| goto out_err; |
| } |
| if (dev->msg->flags & I2C_M_RD) { |
| int i; |
| unsigned dval = 0; |
| for (i = 0; dev->pos < dev->msg->len; i++, dev->pos++) { |
| unsigned rd_status = readl(dev->qup_base + QUP_OPERATIONAL); |
| if (i % 2 == 0) { |
| if ((rd_status & QUP_IN_NOT_EMPTY) == 0) |
| break; |
| dval = readl(dev->qup_base + QUP_IN_FIFO_BASE); |
| dev->msg->buf[dev->pos] = dval & 0xFF; |
| } else |
| dev->msg->buf[dev->pos] = ((dval & 0xFF0000) >> 16); |
| } |
| dev->cnt -= i; |
| } else |
| filled = FALSE; /* refill output FIFO */ |
| } while (dev->cnt > 0); |
| if (dev->cnt == 0) { |
| rem--; |
| msgs++; |
| if (rem) { |
| dev->pos = 0; |
| dev->cnt = msgs->len; |
| dev->msg = msgs; |
| } |
| } |
| /* Wait for I2C bus to be idle */ |
| ret = qup_i2c_poll_writeready(dev); |
| if (ret) { |
| dprintf(INFO, "Error waiting for write ready\n"); |
| goto out_err; |
| } |
| } |
| |
| ret = num; |
| out_err: |
| dev->msg = NULL; |
| dev->pos = 0; |
| dev->err = 0; |
| dev->cnt = 0; |
| mask_interrupt(dev->qup_irq); |
| return ret; |
| } |
| |
| struct qup_i2c_dev *qup_i2c_init(uint8_t gsbi_id, |
| unsigned clk_freq, unsigned src_clk_freq) |
| { |
| struct qup_i2c_dev *dev; |
| if (dev_addr != NULL) { |
| return dev_addr; |
| } |
| |
| dev = malloc(sizeof(struct qup_i2c_dev)); |
| if (!dev) { |
| return NULL; |
| } |
| dev = memset(dev, 0, sizeof(struct qup_i2c_dev)); |
| |
| /* Setup base addresses and irq based on gsbi_id */ |
| dev->qup_irq = GSBI_QUP_IRQ(gsbi_id); |
| dev->qup_base = QUP_BASE(gsbi_id); |
| dev->gsbi_base = GSBI_BASE(gsbi_id); |
| dev->gsbi_number = gsbi_id; |
| |
| /* This must be done for qup_i2c_interrupt to work. */ |
| dev_addr = dev; |
| |
| /* Initialize the GPIO for GSBIn as i2c */ |
| gpio_config_i2c(dev->gsbi_number); |
| |
| /* Configure the GSBI Protocol Code for i2c */ |
| writel((GSBI_PROTOCOL_CODE_I2C << |
| GSBI_CTRL_REG_PROTOCOL_CODE_S), GSBI_CTRL_REG(dev->gsbi_base)); |
| |
| /* Set clk_freq and src_clk_freq for i2c. */ |
| dev->clk_freq = clk_freq; |
| dev->src_clk_freq = src_clk_freq; |
| |
| dev->num_irqs = 1; |
| |
| dev->one_bit_t = USEC_PER_SEC / dev->clk_freq; |
| dev->clk_ctl = 0; |
| |
| /* Register the GSBIn QUP IRQ */ |
| register_int_handler(dev->qup_irq, (int_handler) qup_i2c_interrupt, 0); |
| |
| /* Then disable it */ |
| mask_interrupt(dev->qup_irq); |
| |
| return dev; |
| } |
| |
| int qup_i2c_deinit(struct qup_i2c_dev *dev) |
| { |
| /* Disable the qup_irq */ |
| mask_interrupt(dev->qup_irq); |
| /* Free the memory used for dev */ |
| free(dev); |
| return 0; |
| } |