blob: a243e84e1f7c899e174bc7752f67c1b7c20df4e6 [file] [log] [blame]
/* Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are
* met:
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above
* copyright notice, this list of conditions and the following
* disclaimer in the documentation and/or other materials provided
* with the distribution.
* * Neither the name of The Linux Foundation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
* BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
* WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
* OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
* IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef __PLATFORM_SDHCI_H_
#define __PLATFORM_SDHCI_H_
#include <reg.h>
#include <bits.h>
#include <kernel/event.h>
//#define DEBUG_SDHCI
#ifdef DEBUG_SDHCI
#define DBG(...) dprintf(ALWAYS, __VA_ARGS__)
#else
#define DBG(...)
#endif
/*
* Capabilities for the host controller
* These values are read from the capabilities
* register in the controller
*/
struct host_caps {
uint32_t base_clk_rate; /* Max clock rate supported */
uint32_t max_blk_len; /* Max block len supported */
uint8_t bus_width_8bit; /* 8 Bit mode supported */
uint8_t adma_support; /* Adma support */
uint8_t voltage; /* Supported voltage */
uint8_t sdr_support; /* Single Data rate */
uint8_t ddr_support; /* Dual Data rate */
uint8_t sdr50_support; /* UHS mode, with 100 MHZ clock */
uint8_t sdr104_support; /* UHS mode, with 200 MHZ clock */
uint8_t hs400_support; /* Hs400 mode, with 400 MHZ clock */
};
/*
* sdhci host structure, holding information about host
* controller parameters
*/
struct sdhci_host {
uint32_t base; /* Base address for the host */
uint32_t cur_clk_rate; /* Running clock rate */
uint32_t timing; /* current timing for the host */
bool tuning_in_progress; /* Tuning is being executed */
event_t* sdhc_event; /* Event for power control irqs */
struct host_caps caps; /* Host capabilities */
struct sdhci_msm_data *msm_host; /* MSM specific host info */
};
/*
* Data pointer to be read/written
*/
struct mmc_data {
void *data_ptr; /* Points to stream of data */
uint32_t blk_sz; /* Block size for the data */
uint32_t num_blocks; /* num of blocks, each always of size SDHCI_MMC_BLK_SZ */
};
/*
* mmc command structure as per the spec
*/
struct mmc_command {
uint16_t cmd_index; /* Command index */
uint32_t argument; /* Command argument */
uint8_t data_present; /* Command has data */
uint8_t cmd_type; /* command type */
uint16_t resp_type; /* Response type of the command */
uint32_t resp[4]; /* 128 bit response value */
uint32_t trans_mode; /* Transfer mode, read/write */
uint32_t cmd_retry; /* Retry the command, if card is busy */
uint32_t cmd23_support; /* If card supports cmd23 */
struct mmc_data data; /* Data pointer */
};
/*
* Descriptor table for adma
*/
struct desc_entry {
uint16_t tran_att; /* Attribute for transfer data */
uint16_t len; /* Length of data */
uint32_t addr; /* Address of the data */
};
/*
* Command types for sdhci
*/
enum {
SDHCI_CMD_TYPE_NORMAL = 0,
SDHCI_CMD_TYPE_SUSPEND,
SDHCI_CMD_TYPE_RESUME,
SDHCI_CMD_TYPE_ABORT,
} sdhci_cmd_type;
/*
* Response type values for sdhci
*/
enum {
SDHCI_CMD_RESP_NONE = 0,
SDHCI_CMD_RESP_136,
SDHCI_CMD_RESP_48,
SDHCI_CMD_RESP_48_BUSY,
} sdhci_resp_type;
/*
* Helper macros for writing byte, word & long registers
*/
#define REG_READ8(host, a) readb(host->base + a)
#define REG_WRITE8(host, v, a) writeb(v, (host->base + a))
#define REG_READ32(host, a) readl(host->base + a)
#define REG_WRITE32(host, v, a) writel(v, (host->base + a))
#define REG_RMW32(host, a, s, w, v) RMWREG32((host->base + a), s, w, v)
#define REG_READ16(host, a) readhw(host->base + a)
#define REG_WRITE16(host, v, a) writehw(v, (host->base + a))
/*
* SDHCI registers, as per the host controller spec v 3.0
*/
#define SDHCI_ARG2_REG (0x000)
#define SDHCI_BLKSZ_REG (0x004)
#define SDHCI_BLK_CNT_REG (0x006)
#define SDHCI_ARGUMENT_REG (0x008)
#define SDHCI_TRANS_MODE_REG (0x00C)
#define SDHCI_CMD_REG (0x00E)
#define SDHCI_RESP_REG (0x010)
#define SDHCI_PRESENT_STATE_REG (0x024)
#define SDHCI_HOST_CTRL1_REG (0x028)
#define SDHCI_PWR_CTRL_REG (0x029)
#define SDHCI_CLK_CTRL_REG (0x02C)
#define SDHCI_TIMEOUT_REG (0x02E)
#define SDHCI_RESET_REG (0x02F)
#define SDHCI_NRML_INT_STS_REG (0x030)
#define SDHCI_ERR_INT_STS_REG (0x032)
#define SDHCI_NRML_INT_STS_EN_REG (0x034)
#define SDHCI_ERR_INT_STS_EN_REG (0x036)
#define SDHCI_NRML_INT_SIG_EN_REG (0x038)
#define SDHCI_ERR_INT_SIG_EN_REG (0x03A)
#define SDHCI_AUTO_CMD_ERR (0x03C)
#define SDHCI_HOST_CTRL2_REG (0x03E)
#define SDHCI_CAPS_REG1 (0x040)
#define SDHCI_CAPS_REG2 (0x044)
#define SDHCI_ADM_ERR_REG (0x054)
#define SDHCI_ADM_ADDR_REG (0x058)
/*
* Helper macros for register writes
*/
#define SDHCI_SOFT_RESET BIT(0)
#define SOFT_RESET_CMD BIT(1)
#define SOFT_RESET_DATA BIT(2)
#define SDHCI_RESET_MAX_TIMEOUT 0x64
#define SDHCI_1_8_VOL_SET BIT(3)
/*
* Interrupt related
*/
#define SDHCI_NRML_INT_STS_EN 0x000B
#define SDHCI_ERR_INT_STS_EN 0xFFFF
#define SDHCI_NRML_INT_SIG_EN 0x000B
#define SDHCI_ERR_INT_SIG_EN 0xFFFF
#define SDCC_HC_INT_CARD_REMOVE BIT(7)
#define SDCC_HC_INT_CARD_INSERT BIT(6)
/*
* HC mode enable/disable
*/
#define SDHCI_HC_MODE_EN BIT(0)
#define SDHCI_HC_MODE_DIS (0 << 1)
/*
* Clk control related
*/
#define SDHCI_CLK_MAX_DIV 2046
#define SDHCI_SDCLK_FREQ_SEL 8
#define SDHCI_SDCLK_UP_BIT_SEL 6
#define SDHCI_SDCLK_FREQ_MASK 0xFF
#define SDHC_SDCLK_UP_BIT_MASK 0x300
#define SDHCI_INT_CLK_EN BIT(0)
#define SDHCI_CLK_STABLE_MASK BIT(1)
#define SDHCI_CLK_STABLE BIT(1)
#define SDHCI_CLK_EN BIT(2)
#define SDHCI_CLK_DIS (0 << 2)
#define SDHCI_CLK_RATE_MASK 0x0000FF00
#define SDHCI_CLK_RATE_BIT 8
#define SDHCI_CMD_ACT BIT(0)
#define SDHCI_DAT_ACT BIT(1)
/*
* Bus voltage related macros
*/
#define SDHCI_BUS_VOL_SEL 1
#define SDHCI_BUS_PWR_EN BIT(0)
#define SDHCI_VOL_1_8 5
#define SDHCI_VOL_3_0 6
#define SDHCI_VOL_3_3 7
#define SDHCI_3_3_VOL_MASK 0x01000000
#define SDHCI_3_0_VOL_MASK 0x02000000
#define SDHCI_1_8_VOL_MASK 0x04000000
/*
* Bus width related macros
*/
#define SDHCI_8BIT_WIDTH_MASK 0x00040000
#define SDHCI_BUS_WITDH_1BIT (0)
#define SDHCI_BUS_WITDH_4BIT BIT(1)
#define SDHCI_BUS_WITDH_8BIT BIT(5)
/*
* Adma related macros
*/
#define SDHCI_BLK_LEN_MASK 0x00030000
#define SDHCI_BLK_LEN_BIT 16
#define SDHCI_BLK_ADMA_MASK 0x00080000
#define SDHCI_INT_STS_TRANS_COMPLETE BIT(1)
#define SDHCI_STATE_CMD_DAT_MASK 0x0003
#define SDHCI_INT_STS_CMD_COMPLETE BIT(0)
#define SDHCI_ERR_INT_STAT_MASK 0x8000
#define SDHCI_ADMA_DESC_LINE_SZ 65536
#define SDHCI_ADMA_MAX_TRANS_SZ (65535 * 512)
#define SDHCI_ADMA_TRANS_VALID BIT(0)
#define SDHCI_ADMA_TRANS_END BIT(1)
#define SDHCI_ADMA_TRANS_DATA BIT(5)
#define SDHCI_MMC_BLK_SZ 512
#define SDHCI_MMC_CUR_BLK_CNT_BIT 16
#define SDHCI_MMC_BLK_SZ_BIT 0
#define SDHCI_TRANS_MULTI BIT(5)
#define SDHCI_TRANS_SINGLE (0 << 5)
#define SDHCI_BLK_CNT_EN BIT(1)
#define SDHCI_DMA_EN BIT(0)
#define SDHCI_AUTO_CMD23_EN BIT(3)
#define SDHCI_AUTO_CMD12_EN BIT(2)
#define SDHCI_ADMA_32BIT BIT(4)
/*
* Command related macros
*/
#define SDHCI_CMD_RESP_TYPE_SEL_BIT 0
#define SDHCI_CMD_CRC_CHECK_BIT 3
#define SDHCI_CMD_IDX_CHECK_BIT 4
#define SDHCI_CMD_DATA_PRESENT_BIT 5
#define SDHCI_CMD_CMD_TYPE_BIT 6
#define SDHCI_CMD_CMD_IDX_BIT 8
#define SDHCI_CMD_TIMEOUT_MASK BIT(0)
#define SDHCI_CMD_CRC_MASK BIT(1)
#define SDHCI_CMD_END_BIT_MASK BIT(2)
#define SDHCI_CMD_IDX_MASK BIT(3)
#define SDHCI_DAT_TIMEOUT_MASK BIT(4)
#define SDHCI_DAT_CRC_MASK BIT(5)
#define SDHCI_DAT_END_BIT_MASK BIT(6)
#define SDHCI_CUR_LIM_MASK BIT(7)
#define SDHCI_AUTO_CMD12_MASK BIT(8)
#define SDHCI_ADMA_MASK BIT(9)
#define SDHCI_READ_MODE BIT(4)
#define SDHCI_SWITCH_CMD 6
#define SDHCI_CMD_TIMEOUT 0xF
#define SDHCI_MAX_CMD_RETRY 10000
#define SDHCI_MAX_TRANS_RETRY 10000
#define SDHCI_PREP_CMD(c, f) ((((c) & 0xff) << 8) | ((f) & 0xff))
/*
* command response related
*/
#define SDHCI_RESP_LSHIFT 8
#define SDHCI_RESP_RSHIFT 24
/*
* Power control relatd macros
*/
#define SDCC_HC_PWR_CTRL_INT 0xF
#define SDCC_HC_BUS_ON BIT(0)
#define SDCC_HC_BUS_OFF BIT(1)
#define SDCC_HC_BUS_ON_OFF_SUCC BIT(0)
#define SDCC_HC_IO_SIG_LOW BIT(2)
#define SDCC_HC_IO_SIG_HIGH BIT(3)
#define SDCC_HC_IO_SIG_SUCC BIT(2)
/*
* Command response
*/
#define SDHCI_CMD_RESP_NONE 0
#define SDHCI_CMD_RESP_R1 BIT(0)
#define SDHCI_CMD_RESP_R1B BIT(1)
#define SDHCI_CMD_RESP_R2 BIT(2)
#define SDHCI_CMD_RESP_R3 BIT(3)
#define SDHCI_CMD_RESP_R6 BIT(6)
#define SDHCI_CMD_RESP_R7 BIT(7)
/*
* Clock Divider values
*/
#define SDHCI_CLK_400KHZ 400000
#define SDHCI_CLK_25MHZ 25000000
#define SDHCI_CLK_50MHZ 50000000
#define SDHCI_CLK_100MHZ 100000000
#define SDHCI_CLK_200MHZ 200000000
#define SDHCI_CLK_400MHZ 400000000
/* UHS macros */
#define SDHCI_UHS_MODE_MASK 0x0007
/* DDR mode related macros */
#define SDHCI_DDR50_MODE_EN 0x0004
#define SDHCI_DDR50_MODE_MASK BIT(2)
/* HS200/SDR50 mode related macros */
#define SDHCI_SDR25_MODE_EN 0x0001
#define SDHCI_SDR12_MODE_EN 0x0000
#define SDHCI_SDR50_MODE_MASK BIT(0)
#define SDHCI_SDR50_MODE_EN 0x0002
#define SDHCI_SDR104_MODE_MASK BIT(1)
#define SDHCI_SDR104_MODE_EN 0x0003
#define SDHCI_SDR104_MODE 0x3
#define SDHCI_SDR50_MODE 0x2
#define SDHCI_DDR50_MODE 0x4
#define SDHCI_SDR25_MODE 0x1
#define SDHCI_SDR12_MODE 0x0
/*
* APIs and macros exposed for mmc/sd drivers
*/
#define SDHCI_MMC_WRITE 0
#define SDHCI_MMC_READ 1
#define DATA_BUS_WIDTH_1BIT 0
#define DATA_BUS_WIDTH_4BIT 1
#define DATA_BUS_WIDTH_8BIT 2
#define DATA_DDR_BUS_WIDTH_4BIT 5
#define DATA_DDR_BUS_WIDTH_8BIT 6
/* API: to initialize the controller */
void sdhci_init(struct sdhci_host *);
/* API: Send the command & transfer data using adma */
uint32_t sdhci_send_command(struct sdhci_host *, struct mmc_command *);
/* API: Set the bus width for the contoller */
uint8_t sdhci_set_bus_width(struct sdhci_host *, uint16_t);
/* API: Clock supply for the controller */
uint32_t sdhci_clk_supply(struct sdhci_host *, uint32_t);
/* API: To enable SDR/DDR mode */
void sdhci_set_uhs_mode(struct sdhci_host *, uint32_t);
/* API: Soft reset for the controller */
void sdhci_reset(struct sdhci_host *host, uint8_t mask);
#endif