platform/msm_shared/qmp_usb30_phy.c

/* Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.

 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are
 * met:
 *   * Redistributions of source code must retain the above copyright
 *     notice, this list of conditions and the following disclaimer.
 *   * Redistributions in binary form must reproduce the above
 *     copyright notice, this list of conditions and the following
 *     disclaimer in the documentation and/or other materials provided
 *     with the distribution.
 *   * Neither the name of The Linux Foundation. nor the names of its
 *     contributors may be used to endorse or promote products derived
 *     from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
 * ARE DISCLAIMED.  IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
 * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
 * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
 * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
 * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

#include <sys/types.h>
#include <stdint.h>
#include <platform/clock.h>
#include <platform/iomap.h>
#include <qmp_phy.h>
#include <reg.h>
#include <bits.h>
#include <clock.h>
#include <debug.h>
#include <qtimer.h>
#include <platform.h>
#include <target.h>

#define HS_PHY_COMMON_CTRL             0xEC
#define USE_CORECLK                    BIT(14)
#define PLLBTUNE                       BIT(15)
#define FSEL                           (0x7 << 4)
#define DIS_RETENTION                  BIT(18)
#define QMP_PHY_MAX_TIMEOUT            1000
#define PHYSTATUS                      BIT(6)

static bool hsonly_mode;

/* Override values for QMP 2.0 V1 devices */
struct qmp_reg qmp_override_pll_rev2[] =
{
	{0x124, 0x1C}, /* USB3PHY_QSERDES_COM_VCO_TUNE_CTRL */
	{0x12C, 0x3F}, /* USB3PHY_QSERDES_COM_VCO_TUNE1_MODE0 */
	{0x130, 0x01}, /* USB3PHY_QSERDES_COM_VCO_TUNE2_MODE0 */
	{0x6c4, 0x13}, /* USB3_PHY_FLL_CNTRL2 */
};

/* QMP settings for 2.0 QMP V2 HW */
struct qmp_reg qmp_settings_rev2[] =
{
	{0xAC, 0x14}, /* QSERDES_COM_SYSCLK_EN_SEL */
	{0x34, 0x08}, /* QSERDES_COM_BIAS_EN_CLKBUFLR_EN */
	{0x174, 0x30}, /* QSERDES_COM_CLK_SELECT */
	{0x194, 0x06}, /* QSERDES_COM_CMN_CONFIG */
	{0x19c, 0x01}, /* QSERDES_COM_SVS_MODE_CLK_SEL */
	{0x178, 0x00}, /* QSERDES_COM_HSCLK_SEL */
	{0x70, 0x0F}, /* USB3PHY_QSERDES_COM_BG_TRIM */
	{0x48, 0x0F}, /* USB3PHY_QSERDES_COM_PLL_IVCO */
	{0x3C, 0x04}, /* QSERDES_COM_SYS_CLK_CTRL */

	/* PLL & Loop filter settings */
	{0xd0, 0x82}, /* QSERDES_COM_DEC_START_MODE0 */
	{0xdc, 0x55}, /* QSERDES_COM_DIV_FRAC_START1_MODE0 */
	{0xe0, 0x55}, /* QSERDES_COM_DIV_FRAC_START2_MODE0 */
	{0xe4, 0x03}, /* QSERDES_COM_DIV_FRAC_START3_MODE0 */
	{0x78, 0x0b}, /* QSERDES_COM_CP_CTRL_MODE0 */
	{0x84, 0x16}, /* QSERDES_COM_PLL_RCTRL_MODE0 */
	{0x90, 0x28}, /* QSERDES_COM_PLL_CCTRL_MODE0 */
	{0x108, 0x80}, /* QSERDES_COM_INTEGLOOP_GAIN0_MODE0 */
	{0x124, 0x00}, /* QSERDES_COM_VCO_TUNE_CTRL */
	{0x4c, 0x15}, /* QSERDES_COM_LOCK_CMP1_MODE0 */
	{0x50, 0x34}, /* QSERDES_COM_LOCK_CMP2_MODE0 */
	{0x54, 0x00}, /* QSERDES_COM_LOCK_CMP3_MODE0 */
	{0x18c, 0x00}, /* QSERDES_COM_CORE_CLK_EN */
	{0xcc, 0x00}, /* QSERDES_COM_LOCK_CMP_CFG */
	{0x0C, 0x0A}, /* QSERDES_COM_BG_TIMER */
	{0x128, 0x00}, /* QSERDES_COM_VCO_TUNE_MAP */
	{0xc, 0x0a}, /* QSERDES_COM_BG_TIMER */

	/* SSC settings */
	{0x10, 0x01}, /* QSERDES_COM_SSC_EN_CENTER */
	{0x1c, 0x31}, /* QSERDES_COM_SSC_PER1 */
	{0x20, 0x01}, /* QSERDES_COM_SSC_PER2 */
	{0x14, 0x00}, /* QSERDES_COM_SSC_ADJ_PER1 */
	{0x18, 0x00}, /* QSERDES_COM_SSC_ADJ_PER2 */
	{0x24, 0xde}, /* QSERDES_COM_SSC_STEP_SIZE1 */
	{0x28, 0x07}, /* QSERDES_COM_SSC_STEP_SIZE2 */

	/* Rx Settings */
	{0x440, 0x0b}, /* QSERDES_RX_UCDR_FASTLOCK_FO_GAIN */
	{0x41C, 0x04}, /* QSERDES_RX_UCDR_SO_GAIN */
	{0x4d8, 0x02}, /* QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 */
	{0x4dc, 0x4c}, /* QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3 */
	{0x4e0, 0xbb}, /* QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4 */
	{0x508, 0x77}, /* QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 */
	{0x50c, 0x80}, /* QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2 */
	{0x514, 0x03}, /* QSERDES_RX_SIGDET_CNTRL */
	{0x518, 0x18}, /* QSERDES_RX_SIGDET_LVL */
	{0x51c, 0x16}, /* QSERDES_RX_SIGDET_DEGLITCH_CNTRL */

	/* Tx settings */
	{0x268, 0x45}, /* QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN */
	{0x2ac, 0x12}, /* QSERDES_TX_RCV_DETECT_LVL_2 */
	{0x294, 0x06}, /* QSERDES_TX_LANE_MODE */

	/* FLL settings */
	{0x6c4, 0x03}, /* USB3_PHY_FLL_CNTRL2 */
	{0x6c0, 0x02}, /* USB3_PHY_FLL_CNTRL1 */
	{0x6c8, 0x09}, /* USB3_PHY_FLL_CNT_VAL_L */
	{0x6cc, 0x42}, /* USB3_PHY_FLL_CNT_VAL_H_TOL */
	{0x6d0, 0x85}, /* USB3_PHY_FLL_MAN_CODE */

	/* Lock Det Settings */
	{0x680, 0xd1}, /* USB3_PHY_LOCK_DETECT_CONFIG1 */
	{0x684, 0x1f}, /* USB3_PHY_LOCK_DETECT_CONFIG2 */
	{0x688, 0x47}, /* USB3_PHY_LOCK_DETECT_CONFIG3 */
	{0x664, 0x08}, /* USB3_PHY_POWER_STATE_CONFIG2 */
	{0x608, 0x03}, /* USB3_PHY_START_CONTROL */
	{0x600, 0x00}, /* USB3_PHY_SW_RESET */
};

#if PLATFORM_USE_QMP_MISC
struct qmp_reg qmp_misc_settings_rev2[] =
{
	{0x178, 0x01}, /* QSERDES_COM_HSCLK_SEL */
	{0x518, 0x1B}, /* QSERDES_RX_SIGDET_LVL */
	{0xC4, 0x15}, /* USB3PHY_QSERDES_COM_RESCODE_DIV_NUM */
	{0x1B8, 0x1F}, /* QSERDES_COM_CMN_MISC2 */
};
#endif

__WEAK uint32_t target_override_pll()
{
	return 0;
}

__WEAK uint32_t platform_get_qmp_rev()
{
	return 0x10000000;
}

/* USB3.0 QMP phy reset */
static void qmp_phy_qmp_reset(void)
{
	int ret = 0;
	uint32_t val;
	bool phy_com_reset = false;

	struct clk *usb2b_clk = NULL;
	struct clk *usb_pipe_clk = NULL;
	struct clk *phy_com_clk = NULL;
	struct clk *phy_clk = NULL;

	/* Look if phy com clock is present */
	phy_com_clk = clk_get("usb30_phy_com_reset");
	if (phy_com_clk)
		phy_com_reset = true;

	usb2b_clk = clk_get("usb2b_phy_sleep_clk");
	ASSERT(usb2b_clk);

	phy_clk  = clk_get("usb30_phy_reset");
	ASSERT(phy_clk);

	usb_pipe_clk = clk_get("usb30_pipe_clk");
	ASSERT(usb_pipe_clk);

	/* ASSERT */
	ret = clk_reset(usb2b_clk, CLK_RESET_ASSERT);
	if (ret)
	{
		dprintf(CRITICAL, "Failed to assert usb2b_phy_clk\n");
		return;
	}

	if (phy_com_reset)
	{
		ret = clk_reset(phy_com_clk, CLK_RESET_ASSERT);
		if (ret)
		{
			dprintf(CRITICAL, "Failed to assert phy_com_clk\n");
			goto deassert_usb2b_clk;
		}
	}

	ret = clk_reset(phy_clk, CLK_RESET_ASSERT);
	if (ret)
	{
		dprintf(CRITICAL, "Failed to assert phy_clk\n");
		goto deassert_phy_com_clk;
	}

	ret = clk_reset(usb_pipe_clk, CLK_RESET_ASSERT);
	if (ret)
	{
		dprintf(CRITICAL, "Failed to assert usb_pipe_clk\n");
		goto deassert_phy_clk;
	}

	udelay(100);

	/* DEASSERT */
	ret = clk_reset(usb_pipe_clk, CLK_RESET_DEASSERT);
	if (ret)
		dprintf(CRITICAL, "Failed to deassert usb_pipe_clk\n");

deassert_phy_clk:
	ret = clk_reset(phy_clk, CLK_RESET_DEASSERT);
	if (ret)
		dprintf(CRITICAL, "Failed to deassert phy_clk\n");

deassert_phy_com_clk:
	if (phy_com_reset)
	{
		ret = clk_reset(phy_com_clk, CLK_RESET_DEASSERT);
		if (ret)
			dprintf(CRITICAL, "Failed to deassert phy_com_clk\n");
	}

deassert_usb2b_clk:
	ret = clk_reset(usb2b_clk, CLK_RESET_DEASSERT);
	if (ret)
		dprintf(CRITICAL, "Failed to deassert usb2b_phy_clk\n");

	/* Override the phy common control values */
	val = readl(MSM_USB30_QSCRATCH_BASE + HS_PHY_COMMON_CTRL);
	val |= USE_CORECLK | PLLBTUNE;
	val &= ~FSEL;
	val &= ~DIS_RETENTION;
	writel(val, MSM_USB30_QSCRATCH_BASE + HS_PHY_COMMON_CTRL);
}

/* USB3.0 QMP phy reset */
void usb30_qmp_phy_reset(void)
{
#if USB_RESET_FROM_CLK
	clock_reset_usb_phy();
#else
	qmp_phy_qmp_reset();
#endif
}

/* USB 3.0 phy init: HPG for QMP phy*/
void usb30_qmp_phy_init()
{
	int timeout = QMP_PHY_MAX_TIMEOUT;
	uint32_t phy_status = 0;
	uint32_t qmp_reg_size;
	uint32_t i;


#if USE_TARGET_QMP_SETTINGS
	struct qmp_reg *target_qmp_settings = NULL;
	qmp_reg_size = target_get_qmp_regsize();
	target_qmp_settings = target_get_qmp_settings();
	if (qmp_reg_size && target_qmp_settings)
	{
		for (i = 0 ; i < qmp_reg_size; i++)
		{
			/* As per the hw document we need to add a delay of 1 ms after setting
			 * QSERDES_COM_RESETSM_CNTRL2 and before setting QSERDES_COM_CMN_CONFIG */
			if (i == 7)
				mdelay(1);
			writel(target_qmp_settings[i].val, QMP_PHY_BASE + target_qmp_settings[i].off);
		}
	goto phy_status;
	}
#endif

	uint32_t rev_id = platform_get_qmp_rev();

	/* Sequence as per HPG */
	writel(0x01, QMP_PHY_BASE + PCIE_USB3_PHY_POWER_DOWN_CONTROL);

	if (rev_id >= 0x20000000)
	{
		qmp_reg_size = sizeof(qmp_settings_rev2) / sizeof(struct qmp_reg);
		for (i = 0 ; i < qmp_reg_size; i++)
			writel(qmp_settings_rev2[i].val, QMP_PHY_BASE + qmp_settings_rev2[i].off);

#if PLATFORM_USE_QMP_MISC
		if (platform_use_qmp_misc_settings())
			for (i = 0; i < ARRAY_SIZE(qmp_misc_settings_rev2); i++)
				writel(qmp_misc_settings_rev2[i].val, QMP_PHY_BASE + qmp_misc_settings_rev2[i].off);
#endif
		if (target_override_pll())
		{
			qmp_reg_size = sizeof(qmp_override_pll_rev2) / sizeof(struct qmp_reg);
			for (i = 0 ; i < qmp_reg_size; i++)
				writel(qmp_override_pll_rev2[i].val, QMP_PHY_BASE + qmp_override_pll_rev2[i].off);
		}
	}
	else
	{
		writel(0x08, QMP_PHY_BASE + QSERDES_COM_SYSCLK_EN_SEL_TXBAND);

		if (target_override_pll())
			writel(0xE1, QMP_PHY_BASE + QSERDES_COM_PLL_VCOTAIL_EN);

		writel(0x82, QMP_PHY_BASE + QSERDES_COM_DEC_START1);
		writel(0x03, QMP_PHY_BASE + QSERDES_COM_DEC_START2);
		writel(0xD5, QMP_PHY_BASE + QSERDES_COM_DIV_FRAC_START1);
		writel(0xAA, QMP_PHY_BASE + QSERDES_COM_DIV_FRAC_START2);
		writel(0x4D, QMP_PHY_BASE + QSERDES_COM_DIV_FRAC_START3);
		writel(0x01, QMP_PHY_BASE + QSERDES_COM_PLLLOCK_CMP_EN);
		writel(0x2B, QMP_PHY_BASE + QSERDES_COM_PLLLOCK_CMP1);
		writel(0x68, QMP_PHY_BASE + QSERDES_COM_PLLLOCK_CMP2);
		writel(0x7C, QMP_PHY_BASE + QSERDES_COM_PLL_CRCTRL);
		writel(0x02, QMP_PHY_BASE + QSERDES_COM_PLL_CP_SETI);
		writel(0x1F, QMP_PHY_BASE + QSERDES_COM_PLL_IP_SETP);
		writel(0x0F, QMP_PHY_BASE + QSERDES_COM_PLL_CP_SETP);
		writel(0x01, QMP_PHY_BASE + QSERDES_COM_PLL_IP_SETI);
		writel(0x0F, QMP_PHY_BASE + QSERDES_COM_IE_TRIM);
		writel(0x0F, QMP_PHY_BASE + QSERDES_COM_IP_TRIM);
		writel(0x46, QMP_PHY_BASE + QSERDES_COM_PLL_CNTRL);

		/* CDR Settings */
		writel(0xDA, QMP_PHY_BASE + QSERDES_RX_CDR_CONTROL1);
		writel(0x42, QMP_PHY_BASE + QSERDES_RX_CDR_CONTROL2);

		/* Calibration Settings */
		writel(0x90, QMP_PHY_BASE + QSERDES_COM_RESETSM_CNTRL);
		if (target_override_pll())
			writel(0x07, QMP_PHY_BASE + QSERDES_COM_RESETSM_CNTRL2);
		else
			writel(0x05, QMP_PHY_BASE + QSERDES_COM_RESETSM_CNTRL2);

		writel(0x20, QMP_PHY_BASE + QSERDES_COM_RES_CODE_START_SEG1);
		writel(0x77, QMP_PHY_BASE + QSERDES_COM_RES_CODE_CAL_CSR);
		writel(0x15, QMP_PHY_BASE + QSERDES_COM_RES_TRIM_CONTROL);
		writel(0x03, QMP_PHY_BASE + QSERDES_TX_RCV_DETECT_LVL);
		writel(0x02, QMP_PHY_BASE + QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2);
		writel(0x6C, QMP_PHY_BASE + QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3);
		writel(0xC7, QMP_PHY_BASE + QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4);
		writel(0x40, QMP_PHY_BASE + QSERDES_RX_SIGDET_ENABLES);
		writel(0x73, QMP_PHY_BASE + QSERDES_RX_SIGDET_CNTRL);
		writel(0x06, QMP_PHY_BASE + QSERDES_RX_SIGDET_DEGLITCH_CNTRL);
		writel(0x48, QMP_PHY_BASE + PCIE_USB3_PHY_RX_IDLE_DTCT_CNTRL);
		writel(0x01, QMP_PHY_BASE + QSERDES_COM_SSC_EN_CENTER);
		writel(0x02, QMP_PHY_BASE + QSERDES_COM_SSC_ADJ_PER1);
		writel(0x31, QMP_PHY_BASE + QSERDES_COM_SSC_PER1);
		writel(0x01, QMP_PHY_BASE + QSERDES_COM_SSC_PER2);
		writel(0x19, QMP_PHY_BASE + QSERDES_COM_SSC_STEP_SIZE1);
		writel(0x19, QMP_PHY_BASE + QSERDES_COM_SSC_STEP_SIZE2);
		writel(0x08, QMP_PHY_BASE + PCIE_USB3_PHY_POWER_STATE_CONFIG2);

		writel(0x00, QMP_PHY_BASE + PCIE_USB3_PHY_SW_RESET);
		writel(0x03, QMP_PHY_BASE + PCIE_USB3_PHY_START);
	}

#if USE_TARGET_QMP_SETTINGS
phy_status:
#endif

	/* For future targets defined USB3_PHY_STATUS in the iomap.h
	 * Initial version of driver was written thinking phy_status register
	 * address would not change, but the address keeps changing for every chip
	 * so better get the address from iomap amd keep the backward compatibility
	 */
#if USB3_PHY_STATUS
	phy_status = USB3_PHY_STATUS;
#else
	if (rev_id >= 0x20000000)
		phy_status = QMP_PHY_BASE + 0x77c;
	else
		phy_status = QMP_PHY_BASE + 0x728;
#endif

	while ((readl(phy_status) & PHYSTATUS))
	{
		udelay(1);
		timeout--;
		if (!timeout)
		{
			dprintf(CRITICAL, "QMP phy initialization failed, fallback to HighSpeed only mode\n");
			hsonly_mode = true;
			return;
		}
	}

	clock_bumpup_pipe3_clk();
}

bool use_hsonly_mode()
{
	return hsonly_mode;
}