include/linux/mfd/stmpe.h - kernel/msm-4.19 - Gitiles

 /*
  * Copyright (C) ST-Ericsson SA 2010
  *
  * License Terms: GNU General Public License, version 2
  * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
  */

 #ifndef __LINUX_MFD_STMPE_H
 #define __LINUX_MFD_STMPE_H

 #include <linux/device.h>

 enum stmpe_block {
 	STMPE_BLOCK_GPIO	= 1 << 0,
 	STMPE_BLOCK_KEYPAD	= 1 << 1,
 	STMPE_BLOCK_TOUCHSCREEN	= 1 << 2,
 	STMPE_BLOCK_ADC		= 1 << 3,
 	STMPE_BLOCK_PWM		= 1 << 4,
 	STMPE_BLOCK_ROTATOR	= 1 << 5,
 };

 enum stmpe_partnum {
 	STMPE610,
 	STMPE811,
 	STMPE1601,
 	STMPE2401,
 	STMPE2403,
 };

 /*
  * For registers whose locations differ on variants,  the correct address is
  * obtained by indexing stmpe->regs with one of the following.
  */
 enum {
 	STMPE_IDX_CHIP_ID,
 	STMPE_IDX_ICR_LSB,
 	STMPE_IDX_IER_LSB,
 	STMPE_IDX_ISR_MSB,
 	STMPE_IDX_GPMR_LSB,
 	STMPE_IDX_GPSR_LSB,
 	STMPE_IDX_GPCR_LSB,
 	STMPE_IDX_GPDR_LSB,
 	STMPE_IDX_GPEDR_MSB,
 	STMPE_IDX_GPRER_LSB,
 	STMPE_IDX_GPFER_LSB,
 	STMPE_IDX_GPAFR_U_MSB,
 	STMPE_IDX_IEGPIOR_LSB,
 	STMPE_IDX_ISGPIOR_MSB,
 	STMPE_IDX_MAX,
 };


 struct stmpe_variant_info;
 struct stmpe_client_info;

 /**
  * struct stmpe - STMPE MFD structure
  * @lock: lock protecting I/O operations
  * @irq_lock: IRQ bus lock
  * @dev: device, mostly for dev_dbg()
  * @client: client - i2c or spi
  * @ci: client specific information
  * @partnum: part number
  * @variant: the detected STMPE model number
  * @regs: list of addresses of registers which are at different addresses on
  *	  different variants.  Indexed by one of STMPE_IDX_*.
  * @irq: irq number for stmpe
  * @irq_base: starting IRQ number for internal IRQs
  * @num_gpios: number of gpios, differs for variants
  * @ier: cache of IER registers for bus_lock
  * @oldier: cache of IER registers for bus_lock
  * @pdata: platform data
  */
 struct stmpe {
 	struct mutex lock;
 	struct mutex irq_lock;
 	struct device *dev;
 	void *client;
 	struct stmpe_client_info *ci;
 	enum stmpe_partnum partnum;
 	struct stmpe_variant_info *variant;
 	const u8 *regs;

 	int irq;
 	int irq_base;
 	int num_gpios;
 	u8 ier[2];
 	u8 oldier[2];
 	struct stmpe_platform_data *pdata;
 };

 extern int stmpe_reg_write(struct stmpe *stmpe, u8 reg, u8 data);
 extern int stmpe_reg_read(struct stmpe *stmpe, u8 reg);
 extern int stmpe_block_read(struct stmpe *stmpe, u8 reg, u8 length,
 			    u8 *values);
 extern int stmpe_block_write(struct stmpe *stmpe, u8 reg, u8 length,
 			     const u8 *values);
 extern int stmpe_set_bits(struct stmpe *stmpe, u8 reg, u8 mask, u8 val);
 extern int stmpe_set_altfunc(struct stmpe *stmpe, u32 pins,
 			     enum stmpe_block block);
 extern int stmpe_enable(struct stmpe *stmpe, unsigned int blocks);
 extern int stmpe_disable(struct stmpe *stmpe, unsigned int blocks);

 struct matrix_keymap_data;

 /**
  * struct stmpe_keypad_platform_data - STMPE keypad platform data
  * @keymap_data: key map table and size
  * @debounce_ms: debounce interval, in ms.  Maximum is
  *		 %STMPE_KEYPAD_MAX_DEBOUNCE.
  * @scan_count: number of key scanning cycles to confirm key data.
  *		Maximum is %STMPE_KEYPAD_MAX_SCAN_COUNT.
  * @no_autorepeat: disable key autorepeat
  */
 struct stmpe_keypad_platform_data {
 	struct matrix_keymap_data *keymap_data;
 	unsigned int debounce_ms;
 	unsigned int scan_count;
 	bool no_autorepeat;
 };

 #define STMPE_GPIO_NOREQ_811_TOUCH	(0xf0)

 /**
  * struct stmpe_gpio_platform_data - STMPE GPIO platform data
  * @gpio_base: first gpio number assigned.  A maximum of
  *	       %STMPE_NR_GPIOS GPIOs will be allocated.
  * @norequest_mask: bitmask specifying which GPIOs should _not_ be
  *		    requestable due to different usage (e.g. touch, keypad)
  *		    STMPE_GPIO_NOREQ_* macros can be used here.
  * @setup: board specific setup callback.
  * @remove: board specific remove callback
  */
 struct stmpe_gpio_platform_data {
 	int gpio_base;
 	unsigned norequest_mask;
 	void (*setup)(struct stmpe *stmpe, unsigned gpio_base);
 	void (*remove)(struct stmpe *stmpe, unsigned gpio_base);
 };

 /**
  * struct stmpe_ts_platform_data - stmpe811 touch screen controller platform
  * data
  * @sample_time: ADC converstion time in number of clock.
  * (0 -> 36 clocks, 1 -> 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks,
  * 4 -> 80 clocks, 5 -> 96 clocks, 6 -> 144 clocks),
  * recommended is 4.
  * @mod_12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
  * @ref_sel: ADC reference source
  * (0 -> internal reference, 1 -> external reference)
  * @adc_freq: ADC Clock speed
  * (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz)
  * @ave_ctrl: Sample average control
  * (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 samples, 3 -> 8 samples)
  * @touch_det_delay: Touch detect interrupt delay
  * (0 -> 10 us, 1 -> 50 us, 2 -> 100 us, 3 -> 500 us,
  * 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms)
  * recommended is 3
  * @settling: Panel driver settling time
  * (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 -> 1 ms,
  * 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms)
  * recommended is 2
  * @fraction_z: Length of the fractional part in z
  * (fraction_z ([0..7]) = Count of the fractional part)
  * recommended is 7
  * @i_drive: current limit value of the touchscreen drivers
  * (0 -> 20 mA typical 35 mA max, 1 -> 50 mA typical 80 mA max)
  *
  * */
 struct stmpe_ts_platform_data {
        u8 sample_time;
        u8 mod_12b;
        u8 ref_sel;
        u8 adc_freq;
        u8 ave_ctrl;
        u8 touch_det_delay;
        u8 settling;
        u8 fraction_z;
        u8 i_drive;
 };

 /**
  * struct stmpe_platform_data - STMPE platform data
  * @id: device id to distinguish between multiple STMPEs on the same board
  * @blocks: bitmask of blocks to enable (use STMPE_BLOCK_*)
  * @irq_trigger: IRQ trigger to use for the interrupt to the host
  * @irq_invert_polarity: IRQ line is connected with reversed polarity
  * @autosleep: bool to enable/disable stmpe autosleep
  * @autosleep_timeout: inactivity timeout in milliseconds for autosleep
  * @irq_base: base IRQ number.  %STMPE_NR_IRQS irqs will be used, or
  *	      %STMPE_NR_INTERNAL_IRQS if the GPIO driver is not used.
  * @irq_over_gpio: true if gpio is used to get irq
  * @irq_gpio: gpio number over which irq will be requested (significant only if
  *	      irq_over_gpio is true)
  * @gpio: GPIO-specific platform data
  * @keypad: keypad-specific platform data
  * @ts: touchscreen-specific platform data
  */
 struct stmpe_platform_data {
 	int id;
 	unsigned int blocks;
 	int irq_base;
 	unsigned int irq_trigger;
 	bool irq_invert_polarity;
 	bool autosleep;
 	bool irq_over_gpio;
 	int irq_gpio;
 	int autosleep_timeout;

 	struct stmpe_gpio_platform_data *gpio;
 	struct stmpe_keypad_platform_data *keypad;
 	struct stmpe_ts_platform_data *ts;
 };

 #define STMPE_NR_INTERNAL_IRQS	9
 #define STMPE_INT_GPIO(x)	(STMPE_NR_INTERNAL_IRQS + (x))

 #define STMPE_NR_GPIOS		24
 #define STMPE_NR_IRQS		STMPE_INT_GPIO(STMPE_NR_GPIOS)

 #endif
	/*
	* Copyright (C) ST-Ericsson SA 2010
	*
	* License Terms: GNU General Public License, version 2
	* Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
	*/

	#ifndef __LINUX_MFD_STMPE_H
	#define __LINUX_MFD_STMPE_H

	#include <linux/device.h>

	enum stmpe_block {
	STMPE_BLOCK_GPIO = 1 << 0,
	STMPE_BLOCK_KEYPAD = 1 << 1,
	STMPE_BLOCK_TOUCHSCREEN = 1 << 2,
	STMPE_BLOCK_ADC = 1 << 3,
	STMPE_BLOCK_PWM = 1 << 4,
	STMPE_BLOCK_ROTATOR = 1 << 5,
	};

	enum stmpe_partnum {
	STMPE610,
	STMPE811,
	STMPE1601,
	STMPE2401,
	STMPE2403,
	};

	/*
	* For registers whose locations differ on variants, the correct address is
	* obtained by indexing stmpe->regs with one of the following.
	*/
	enum {
	STMPE_IDX_CHIP_ID,
	STMPE_IDX_ICR_LSB,
	STMPE_IDX_IER_LSB,
	STMPE_IDX_ISR_MSB,
	STMPE_IDX_GPMR_LSB,
	STMPE_IDX_GPSR_LSB,
	STMPE_IDX_GPCR_LSB,
	STMPE_IDX_GPDR_LSB,
	STMPE_IDX_GPEDR_MSB,
	STMPE_IDX_GPRER_LSB,
	STMPE_IDX_GPFER_LSB,
	STMPE_IDX_GPAFR_U_MSB,
	STMPE_IDX_IEGPIOR_LSB,
	STMPE_IDX_ISGPIOR_MSB,
	STMPE_IDX_MAX,
	};


	struct stmpe_variant_info;
	struct stmpe_client_info;

	/**
	* struct stmpe - STMPE MFD structure
	* @lock: lock protecting I/O operations
	* @irq_lock: IRQ bus lock
	* @dev: device, mostly for dev_dbg()
	* @client: client - i2c or spi
	* @ci: client specific information
	* @partnum: part number
	* @variant: the detected STMPE model number
	* @regs: list of addresses of registers which are at different addresses on
	* different variants. Indexed by one of STMPE_IDX_*.
	* @irq: irq number for stmpe
	* @irq_base: starting IRQ number for internal IRQs
	* @num_gpios: number of gpios, differs for variants
	* @ier: cache of IER registers for bus_lock
	* @oldier: cache of IER registers for bus_lock
	* @pdata: platform data
	*/
	struct stmpe {
	struct mutex lock;
	struct mutex irq_lock;
	struct device *dev;
	void *client;
	struct stmpe_client_info *ci;
	enum stmpe_partnum partnum;
	struct stmpe_variant_info *variant;
	const u8 *regs;

	int irq;
	int irq_base;
	int num_gpios;
	u8 ier[2];
	u8 oldier[2];
	struct stmpe_platform_data *pdata;
	};

	extern int stmpe_reg_write(struct stmpe *stmpe, u8 reg, u8 data);
	extern int stmpe_reg_read(struct stmpe *stmpe, u8 reg);
	extern int stmpe_block_read(struct stmpe *stmpe, u8 reg, u8 length,
	u8 *values);
	extern int stmpe_block_write(struct stmpe *stmpe, u8 reg, u8 length,
	const u8 *values);
	extern int stmpe_set_bits(struct stmpe *stmpe, u8 reg, u8 mask, u8 val);
	extern int stmpe_set_altfunc(struct stmpe *stmpe, u32 pins,
	enum stmpe_block block);
	extern int stmpe_enable(struct stmpe *stmpe, unsigned int blocks);
	extern int stmpe_disable(struct stmpe *stmpe, unsigned int blocks);

	struct matrix_keymap_data;

	/**
	* struct stmpe_keypad_platform_data - STMPE keypad platform data
	* @keymap_data: key map table and size
	* @debounce_ms: debounce interval, in ms. Maximum is
	* %STMPE_KEYPAD_MAX_DEBOUNCE.
	* @scan_count: number of key scanning cycles to confirm key data.
	* Maximum is %STMPE_KEYPAD_MAX_SCAN_COUNT.
	* @no_autorepeat: disable key autorepeat
	*/
	struct stmpe_keypad_platform_data {
	struct matrix_keymap_data *keymap_data;
	unsigned int debounce_ms;
	unsigned int scan_count;
	bool no_autorepeat;
	};

	#define STMPE_GPIO_NOREQ_811_TOUCH (0xf0)

	/**
	* struct stmpe_gpio_platform_data - STMPE GPIO platform data
	* @gpio_base: first gpio number assigned. A maximum of
	* %STMPE_NR_GPIOS GPIOs will be allocated.
	* @norequest_mask: bitmask specifying which GPIOs should _not_ be
	* requestable due to different usage (e.g. touch, keypad)
	* STMPE_GPIO_NOREQ_* macros can be used here.
	* @setup: board specific setup callback.
	* @remove: board specific remove callback
	*/
	struct stmpe_gpio_platform_data {
	int gpio_base;
	unsigned norequest_mask;
	void (setup)(struct stmpe stmpe, unsigned gpio_base);
	void (remove)(struct stmpe stmpe, unsigned gpio_base);
	};

	/**
	* struct stmpe_ts_platform_data - stmpe811 touch screen controller platform
	* data
	* @sample_time: ADC converstion time in number of clock.
	* (0 -> 36 clocks, 1 -> 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks,
	* 4 -> 80 clocks, 5 -> 96 clocks, 6 -> 144 clocks),
	* recommended is 4.
	* @mod_12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC)
	* @ref_sel: ADC reference source
	* (0 -> internal reference, 1 -> external reference)
	* @adc_freq: ADC Clock speed
	* (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 \|\| 3 -> 6.5 MHz)
	* @ave_ctrl: Sample average control
	* (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 samples, 3 -> 8 samples)
	* @touch_det_delay: Touch detect interrupt delay
	* (0 -> 10 us, 1 -> 50 us, 2 -> 100 us, 3 -> 500 us,
	* 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms)
	* recommended is 3
	* @settling: Panel driver settling time
	* (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 -> 1 ms,
	* 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms)
	* recommended is 2
	* @fraction_z: Length of the fractional part in z
	* (fraction_z ([0..7]) = Count of the fractional part)
	* recommended is 7
	* @i_drive: current limit value of the touchscreen drivers
	* (0 -> 20 mA typical 35 mA max, 1 -> 50 mA typical 80 mA max)
	*
	* */
	struct stmpe_ts_platform_data {
	u8 sample_time;
	u8 mod_12b;
	u8 ref_sel;
	u8 adc_freq;
	u8 ave_ctrl;
	u8 touch_det_delay;
	u8 settling;
	u8 fraction_z;
	u8 i_drive;
	};

	/**
	* struct stmpe_platform_data - STMPE platform data
	* @id: device id to distinguish between multiple STMPEs on the same board
	* @blocks: bitmask of blocks to enable (use STMPE_BLOCK_*)
	* @irq_trigger: IRQ trigger to use for the interrupt to the host
	* @irq_invert_polarity: IRQ line is connected with reversed polarity
	* @autosleep: bool to enable/disable stmpe autosleep
	* @autosleep_timeout: inactivity timeout in milliseconds for autosleep
	* @irq_base: base IRQ number. %STMPE_NR_IRQS irqs will be used, or
	* %STMPE_NR_INTERNAL_IRQS if the GPIO driver is not used.
	* @irq_over_gpio: true if gpio is used to get irq
	* @irq_gpio: gpio number over which irq will be requested (significant only if
	* irq_over_gpio is true)
	* @gpio: GPIO-specific platform data
	* @keypad: keypad-specific platform data
	* @ts: touchscreen-specific platform data
	*/
	struct stmpe_platform_data {
	int id;
	unsigned int blocks;
	int irq_base;
	unsigned int irq_trigger;
	bool irq_invert_polarity;
	bool autosleep;
	bool irq_over_gpio;
	int irq_gpio;
	int autosleep_timeout;

	struct stmpe_gpio_platform_data *gpio;
	struct stmpe_keypad_platform_data *keypad;
	struct stmpe_ts_platform_data *ts;
	};

	#define STMPE_NR_INTERNAL_IRQS 9
	#define STMPE_INT_GPIO(x) (STMPE_NR_INTERNAL_IRQS + (x))

	#define STMPE_NR_GPIOS 24
	#define STMPE_NR_IRQS STMPE_INT_GPIO(STMPE_NR_GPIOS)

	#endif