| /* |
| * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/regulator/consumer.h> |
| |
| #include "drm_crtc.h" |
| #include "drm_dp_helper.h" |
| #include "drm_edid.h" |
| #include "edp.h" |
| #include "edp.xml.h" |
| |
| #define VDDA_MIN_UV 1800000 /* uV units */ |
| #define VDDA_MAX_UV 1800000 /* uV units */ |
| #define VDDA_UA_ON_LOAD 100000 /* uA units */ |
| #define VDDA_UA_OFF_LOAD 100 /* uA units */ |
| |
| #define DPCD_LINK_VOLTAGE_MAX 4 |
| #define DPCD_LINK_PRE_EMPHASIS_MAX 4 |
| |
| #define EDP_LINK_BW_MAX DP_LINK_BW_2_7 |
| |
| /* Link training return value */ |
| #define EDP_TRAIN_FAIL -1 |
| #define EDP_TRAIN_SUCCESS 0 |
| #define EDP_TRAIN_RECONFIG 1 |
| |
| #define EDP_CLK_MASK_AHB BIT(0) |
| #define EDP_CLK_MASK_AUX BIT(1) |
| #define EDP_CLK_MASK_LINK BIT(2) |
| #define EDP_CLK_MASK_PIXEL BIT(3) |
| #define EDP_CLK_MASK_MDP_CORE BIT(4) |
| #define EDP_CLK_MASK_LINK_CHAN (EDP_CLK_MASK_LINK | EDP_CLK_MASK_PIXEL) |
| #define EDP_CLK_MASK_AUX_CHAN \ |
| (EDP_CLK_MASK_AHB | EDP_CLK_MASK_AUX | EDP_CLK_MASK_MDP_CORE) |
| #define EDP_CLK_MASK_ALL (EDP_CLK_MASK_AUX_CHAN | EDP_CLK_MASK_LINK_CHAN) |
| |
| #define EDP_BACKLIGHT_MAX 255 |
| |
| #define EDP_INTR_STATUS1 \ |
| (EDP_INTERRUPT_REG_1_HPD | EDP_INTERRUPT_REG_1_AUX_I2C_DONE | \ |
| EDP_INTERRUPT_REG_1_WRONG_ADDR | EDP_INTERRUPT_REG_1_TIMEOUT | \ |
| EDP_INTERRUPT_REG_1_NACK_DEFER | EDP_INTERRUPT_REG_1_WRONG_DATA_CNT | \ |
| EDP_INTERRUPT_REG_1_I2C_NACK | EDP_INTERRUPT_REG_1_I2C_DEFER | \ |
| EDP_INTERRUPT_REG_1_PLL_UNLOCK | EDP_INTERRUPT_REG_1_AUX_ERROR) |
| #define EDP_INTR_MASK1 (EDP_INTR_STATUS1 << 2) |
| #define EDP_INTR_STATUS2 \ |
| (EDP_INTERRUPT_REG_2_READY_FOR_VIDEO | \ |
| EDP_INTERRUPT_REG_2_IDLE_PATTERNs_SENT | \ |
| EDP_INTERRUPT_REG_2_FRAME_END | EDP_INTERRUPT_REG_2_CRC_UPDATED) |
| #define EDP_INTR_MASK2 (EDP_INTR_STATUS2 << 2) |
| |
| struct edp_ctrl { |
| struct platform_device *pdev; |
| |
| void __iomem *base; |
| |
| /* regulators */ |
| struct regulator *vdda_vreg; |
| struct regulator *lvl_vreg; |
| |
| /* clocks */ |
| struct clk *aux_clk; |
| struct clk *pixel_clk; |
| struct clk *ahb_clk; |
| struct clk *link_clk; |
| struct clk *mdp_core_clk; |
| |
| /* gpios */ |
| struct gpio_desc *panel_en_gpio; |
| struct gpio_desc *panel_hpd_gpio; |
| |
| /* completion and mutex */ |
| struct completion idle_comp; |
| struct mutex dev_mutex; /* To protect device power status */ |
| |
| /* work queue */ |
| struct work_struct on_work; |
| struct work_struct off_work; |
| struct workqueue_struct *workqueue; |
| |
| /* Interrupt register lock */ |
| spinlock_t irq_lock; |
| |
| bool edp_connected; |
| bool power_on; |
| |
| /* edid raw data */ |
| struct edid *edid; |
| |
| struct drm_dp_link dp_link; |
| struct drm_dp_aux *drm_aux; |
| |
| /* dpcd raw data */ |
| u8 dpcd[DP_RECEIVER_CAP_SIZE]; |
| |
| /* Link status */ |
| u8 link_rate; |
| u8 lane_cnt; |
| u8 v_level; |
| u8 p_level; |
| |
| /* Timing status */ |
| u8 interlaced; |
| u32 pixel_rate; /* in kHz */ |
| u32 color_depth; |
| |
| struct edp_aux *aux; |
| struct edp_phy *phy; |
| }; |
| |
| struct edp_pixel_clk_div { |
| u32 rate; /* in kHz */ |
| u32 m; |
| u32 n; |
| }; |
| |
| #define EDP_PIXEL_CLK_NUM 8 |
| static const struct edp_pixel_clk_div clk_divs[2][EDP_PIXEL_CLK_NUM] = { |
| { /* Link clock = 162MHz, source clock = 810MHz */ |
| {119000, 31, 211}, /* WSXGA+ 1680x1050@60Hz CVT */ |
| {130250, 32, 199}, /* UXGA 1600x1200@60Hz CVT */ |
| {148500, 11, 60}, /* FHD 1920x1080@60Hz */ |
| {154000, 50, 263}, /* WUXGA 1920x1200@60Hz CVT */ |
| {209250, 31, 120}, /* QXGA 2048x1536@60Hz CVT */ |
| {268500, 119, 359}, /* WQXGA 2560x1600@60Hz CVT */ |
| {138530, 33, 193}, /* AUO B116HAN03.0 Panel */ |
| {141400, 48, 275}, /* AUO B133HTN01.2 Panel */ |
| }, |
| { /* Link clock = 270MHz, source clock = 675MHz */ |
| {119000, 52, 295}, /* WSXGA+ 1680x1050@60Hz CVT */ |
| {130250, 11, 57}, /* UXGA 1600x1200@60Hz CVT */ |
| {148500, 11, 50}, /* FHD 1920x1080@60Hz */ |
| {154000, 47, 206}, /* WUXGA 1920x1200@60Hz CVT */ |
| {209250, 31, 100}, /* QXGA 2048x1536@60Hz CVT */ |
| {268500, 107, 269}, /* WQXGA 2560x1600@60Hz CVT */ |
| {138530, 63, 307}, /* AUO B116HAN03.0 Panel */ |
| {141400, 53, 253}, /* AUO B133HTN01.2 Panel */ |
| }, |
| }; |
| |
| static int edp_clk_init(struct edp_ctrl *ctrl) |
| { |
| struct device *dev = &ctrl->pdev->dev; |
| int ret; |
| |
| ctrl->aux_clk = devm_clk_get(dev, "core_clk"); |
| if (IS_ERR(ctrl->aux_clk)) { |
| ret = PTR_ERR(ctrl->aux_clk); |
| pr_err("%s: Can't find aux_clk, %d\n", __func__, ret); |
| ctrl->aux_clk = NULL; |
| return ret; |
| } |
| |
| ctrl->pixel_clk = devm_clk_get(dev, "pixel_clk"); |
| if (IS_ERR(ctrl->pixel_clk)) { |
| ret = PTR_ERR(ctrl->pixel_clk); |
| pr_err("%s: Can't find pixel_clk, %d\n", __func__, ret); |
| ctrl->pixel_clk = NULL; |
| return ret; |
| } |
| |
| ctrl->ahb_clk = devm_clk_get(dev, "iface_clk"); |
| if (IS_ERR(ctrl->ahb_clk)) { |
| ret = PTR_ERR(ctrl->ahb_clk); |
| pr_err("%s: Can't find ahb_clk, %d\n", __func__, ret); |
| ctrl->ahb_clk = NULL; |
| return ret; |
| } |
| |
| ctrl->link_clk = devm_clk_get(dev, "link_clk"); |
| if (IS_ERR(ctrl->link_clk)) { |
| ret = PTR_ERR(ctrl->link_clk); |
| pr_err("%s: Can't find link_clk, %d\n", __func__, ret); |
| ctrl->link_clk = NULL; |
| return ret; |
| } |
| |
| /* need mdp core clock to receive irq */ |
| ctrl->mdp_core_clk = devm_clk_get(dev, "mdp_core_clk"); |
| if (IS_ERR(ctrl->mdp_core_clk)) { |
| ret = PTR_ERR(ctrl->mdp_core_clk); |
| pr_err("%s: Can't find mdp_core_clk, %d\n", __func__, ret); |
| ctrl->mdp_core_clk = NULL; |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int edp_clk_enable(struct edp_ctrl *ctrl, u32 clk_mask) |
| { |
| int ret; |
| |
| DBG("mask=%x", clk_mask); |
| /* ahb_clk should be enabled first */ |
| if (clk_mask & EDP_CLK_MASK_AHB) { |
| ret = clk_prepare_enable(ctrl->ahb_clk); |
| if (ret) { |
| pr_err("%s: Failed to enable ahb clk\n", __func__); |
| goto f0; |
| } |
| } |
| if (clk_mask & EDP_CLK_MASK_AUX) { |
| ret = clk_set_rate(ctrl->aux_clk, 19200000); |
| if (ret) { |
| pr_err("%s: Failed to set rate aux clk\n", __func__); |
| goto f1; |
| } |
| ret = clk_prepare_enable(ctrl->aux_clk); |
| if (ret) { |
| pr_err("%s: Failed to enable aux clk\n", __func__); |
| goto f1; |
| } |
| } |
| /* Need to set rate and enable link_clk prior to pixel_clk */ |
| if (clk_mask & EDP_CLK_MASK_LINK) { |
| DBG("edp->link_clk, set_rate %ld", |
| (unsigned long)ctrl->link_rate * 27000000); |
| ret = clk_set_rate(ctrl->link_clk, |
| (unsigned long)ctrl->link_rate * 27000000); |
| if (ret) { |
| pr_err("%s: Failed to set rate to link clk\n", |
| __func__); |
| goto f2; |
| } |
| |
| ret = clk_prepare_enable(ctrl->link_clk); |
| if (ret) { |
| pr_err("%s: Failed to enable link clk\n", __func__); |
| goto f2; |
| } |
| } |
| if (clk_mask & EDP_CLK_MASK_PIXEL) { |
| DBG("edp->pixel_clk, set_rate %ld", |
| (unsigned long)ctrl->pixel_rate * 1000); |
| ret = clk_set_rate(ctrl->pixel_clk, |
| (unsigned long)ctrl->pixel_rate * 1000); |
| if (ret) { |
| pr_err("%s: Failed to set rate to pixel clk\n", |
| __func__); |
| goto f3; |
| } |
| |
| ret = clk_prepare_enable(ctrl->pixel_clk); |
| if (ret) { |
| pr_err("%s: Failed to enable pixel clk\n", __func__); |
| goto f3; |
| } |
| } |
| if (clk_mask & EDP_CLK_MASK_MDP_CORE) { |
| ret = clk_prepare_enable(ctrl->mdp_core_clk); |
| if (ret) { |
| pr_err("%s: Failed to enable mdp core clk\n", __func__); |
| goto f4; |
| } |
| } |
| |
| return 0; |
| |
| f4: |
| if (clk_mask & EDP_CLK_MASK_PIXEL) |
| clk_disable_unprepare(ctrl->pixel_clk); |
| f3: |
| if (clk_mask & EDP_CLK_MASK_LINK) |
| clk_disable_unprepare(ctrl->link_clk); |
| f2: |
| if (clk_mask & EDP_CLK_MASK_AUX) |
| clk_disable_unprepare(ctrl->aux_clk); |
| f1: |
| if (clk_mask & EDP_CLK_MASK_AHB) |
| clk_disable_unprepare(ctrl->ahb_clk); |
| f0: |
| return ret; |
| } |
| |
| static void edp_clk_disable(struct edp_ctrl *ctrl, u32 clk_mask) |
| { |
| if (clk_mask & EDP_CLK_MASK_MDP_CORE) |
| clk_disable_unprepare(ctrl->mdp_core_clk); |
| if (clk_mask & EDP_CLK_MASK_PIXEL) |
| clk_disable_unprepare(ctrl->pixel_clk); |
| if (clk_mask & EDP_CLK_MASK_LINK) |
| clk_disable_unprepare(ctrl->link_clk); |
| if (clk_mask & EDP_CLK_MASK_AUX) |
| clk_disable_unprepare(ctrl->aux_clk); |
| if (clk_mask & EDP_CLK_MASK_AHB) |
| clk_disable_unprepare(ctrl->ahb_clk); |
| } |
| |
| static int edp_regulator_init(struct edp_ctrl *ctrl) |
| { |
| struct device *dev = &ctrl->pdev->dev; |
| |
| DBG(""); |
| ctrl->vdda_vreg = devm_regulator_get(dev, "vdda"); |
| if (IS_ERR(ctrl->vdda_vreg)) { |
| pr_err("%s: Could not get vdda reg, ret = %ld\n", __func__, |
| PTR_ERR(ctrl->vdda_vreg)); |
| ctrl->vdda_vreg = NULL; |
| return PTR_ERR(ctrl->vdda_vreg); |
| } |
| ctrl->lvl_vreg = devm_regulator_get(dev, "lvl-vdd"); |
| if (IS_ERR(ctrl->lvl_vreg)) { |
| pr_err("Could not get lvl-vdd reg, %ld", |
| PTR_ERR(ctrl->lvl_vreg)); |
| ctrl->lvl_vreg = NULL; |
| return PTR_ERR(ctrl->lvl_vreg); |
| } |
| |
| return 0; |
| } |
| |
| static int edp_regulator_enable(struct edp_ctrl *ctrl) |
| { |
| int ret; |
| |
| ret = regulator_set_voltage(ctrl->vdda_vreg, VDDA_MIN_UV, VDDA_MAX_UV); |
| if (ret) { |
| pr_err("%s:vdda_vreg set_voltage failed, %d\n", __func__, ret); |
| goto vdda_set_fail; |
| } |
| |
| ret = regulator_set_load(ctrl->vdda_vreg, VDDA_UA_ON_LOAD); |
| if (ret < 0) { |
| pr_err("%s: vdda_vreg set regulator mode failed.\n", __func__); |
| goto vdda_set_fail; |
| } |
| |
| ret = regulator_enable(ctrl->vdda_vreg); |
| if (ret) { |
| pr_err("%s: Failed to enable vdda_vreg regulator.\n", __func__); |
| goto vdda_enable_fail; |
| } |
| |
| ret = regulator_enable(ctrl->lvl_vreg); |
| if (ret) { |
| pr_err("Failed to enable lvl-vdd reg regulator, %d", ret); |
| goto lvl_enable_fail; |
| } |
| |
| DBG("exit"); |
| return 0; |
| |
| lvl_enable_fail: |
| regulator_disable(ctrl->vdda_vreg); |
| vdda_enable_fail: |
| regulator_set_load(ctrl->vdda_vreg, VDDA_UA_OFF_LOAD); |
| vdda_set_fail: |
| return ret; |
| } |
| |
| static void edp_regulator_disable(struct edp_ctrl *ctrl) |
| { |
| regulator_disable(ctrl->lvl_vreg); |
| regulator_disable(ctrl->vdda_vreg); |
| regulator_set_load(ctrl->vdda_vreg, VDDA_UA_OFF_LOAD); |
| } |
| |
| static int edp_gpio_config(struct edp_ctrl *ctrl) |
| { |
| struct device *dev = &ctrl->pdev->dev; |
| int ret; |
| |
| ctrl->panel_hpd_gpio = devm_gpiod_get(dev, "panel-hpd"); |
| if (IS_ERR(ctrl->panel_hpd_gpio)) { |
| ret = PTR_ERR(ctrl->panel_hpd_gpio); |
| ctrl->panel_hpd_gpio = NULL; |
| pr_err("%s: cannot get panel-hpd-gpios, %d\n", __func__, ret); |
| return ret; |
| } |
| |
| ret = gpiod_direction_input(ctrl->panel_hpd_gpio); |
| if (ret) { |
| pr_err("%s: Set direction for hpd failed, %d\n", __func__, ret); |
| return ret; |
| } |
| |
| ctrl->panel_en_gpio = devm_gpiod_get(dev, "panel-en"); |
| if (IS_ERR(ctrl->panel_en_gpio)) { |
| ret = PTR_ERR(ctrl->panel_en_gpio); |
| ctrl->panel_en_gpio = NULL; |
| pr_err("%s: cannot get panel-en-gpios, %d\n", __func__, ret); |
| return ret; |
| } |
| |
| ret = gpiod_direction_output(ctrl->panel_en_gpio, 0); |
| if (ret) { |
| pr_err("%s: Set direction for panel_en failed, %d\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| DBG("gpio on"); |
| |
| return 0; |
| } |
| |
| static void edp_ctrl_irq_enable(struct edp_ctrl *ctrl, int enable) |
| { |
| unsigned long flags; |
| |
| DBG("%d", enable); |
| spin_lock_irqsave(&ctrl->irq_lock, flags); |
| if (enable) { |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_1, EDP_INTR_MASK1); |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_2, EDP_INTR_MASK2); |
| } else { |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_1, 0x0); |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_2, 0x0); |
| } |
| spin_unlock_irqrestore(&ctrl->irq_lock, flags); |
| DBG("exit"); |
| } |
| |
| static void edp_fill_link_cfg(struct edp_ctrl *ctrl) |
| { |
| u32 prate; |
| u32 lrate; |
| u32 bpp; |
| u8 max_lane = ctrl->dp_link.num_lanes; |
| u8 lane; |
| |
| prate = ctrl->pixel_rate; |
| bpp = ctrl->color_depth * 3; |
| |
| /* |
| * By default, use the maximum link rate and minimum lane count, |
| * so that we can do rate down shift during link training. |
| */ |
| ctrl->link_rate = drm_dp_link_rate_to_bw_code(ctrl->dp_link.rate); |
| |
| prate *= bpp; |
| prate /= 8; /* in kByte */ |
| |
| lrate = 270000; /* in kHz */ |
| lrate *= ctrl->link_rate; |
| lrate /= 10; /* in kByte, 10 bits --> 8 bits */ |
| |
| for (lane = 1; lane <= max_lane; lane <<= 1) { |
| if (lrate >= prate) |
| break; |
| lrate <<= 1; |
| } |
| |
| ctrl->lane_cnt = lane; |
| DBG("rate=%d lane=%d", ctrl->link_rate, ctrl->lane_cnt); |
| } |
| |
| static void edp_config_ctrl(struct edp_ctrl *ctrl) |
| { |
| u32 data; |
| enum edp_color_depth depth; |
| |
| data = EDP_CONFIGURATION_CTRL_LANES(ctrl->lane_cnt - 1); |
| |
| if (ctrl->dp_link.capabilities & DP_LINK_CAP_ENHANCED_FRAMING) |
| data |= EDP_CONFIGURATION_CTRL_ENHANCED_FRAMING; |
| |
| depth = EDP_6BIT; |
| if (ctrl->color_depth == 8) |
| depth = EDP_8BIT; |
| |
| data |= EDP_CONFIGURATION_CTRL_COLOR(depth); |
| |
| if (!ctrl->interlaced) /* progressive */ |
| data |= EDP_CONFIGURATION_CTRL_PROGRESSIVE; |
| |
| data |= (EDP_CONFIGURATION_CTRL_SYNC_CLK | |
| EDP_CONFIGURATION_CTRL_STATIC_MVID); |
| |
| edp_write(ctrl->base + REG_EDP_CONFIGURATION_CTRL, data); |
| } |
| |
| static void edp_state_ctrl(struct edp_ctrl *ctrl, u32 state) |
| { |
| edp_write(ctrl->base + REG_EDP_STATE_CTRL, state); |
| /* Make sure H/W status is set */ |
| wmb(); |
| } |
| |
| static int edp_lane_set_write(struct edp_ctrl *ctrl, |
| u8 voltage_level, u8 pre_emphasis_level) |
| { |
| int i; |
| u8 buf[4]; |
| |
| if (voltage_level >= DPCD_LINK_VOLTAGE_MAX) |
| voltage_level |= 0x04; |
| |
| if (pre_emphasis_level >= DPCD_LINK_PRE_EMPHASIS_MAX) |
| pre_emphasis_level |= 0x04; |
| |
| pre_emphasis_level <<= 3; |
| |
| for (i = 0; i < 4; i++) |
| buf[i] = voltage_level | pre_emphasis_level; |
| |
| DBG("%s: p|v=0x%x", __func__, voltage_level | pre_emphasis_level); |
| if (drm_dp_dpcd_write(ctrl->drm_aux, 0x103, buf, 4) < 4) { |
| pr_err("%s: Set sw/pe to panel failed\n", __func__); |
| return -ENOLINK; |
| } |
| |
| return 0; |
| } |
| |
| static int edp_train_pattern_set_write(struct edp_ctrl *ctrl, u8 pattern) |
| { |
| u8 p = pattern; |
| |
| DBG("pattern=%x", p); |
| if (drm_dp_dpcd_write(ctrl->drm_aux, |
| DP_TRAINING_PATTERN_SET, &p, 1) < 1) { |
| pr_err("%s: Set training pattern to panel failed\n", __func__); |
| return -ENOLINK; |
| } |
| |
| return 0; |
| } |
| |
| static void edp_sink_train_set_adjust(struct edp_ctrl *ctrl, |
| const u8 *link_status) |
| { |
| int i; |
| u8 max = 0; |
| u8 data; |
| |
| /* use the max level across lanes */ |
| for (i = 0; i < ctrl->lane_cnt; i++) { |
| data = drm_dp_get_adjust_request_voltage(link_status, i); |
| DBG("lane=%d req_voltage_swing=0x%x", i, data); |
| if (max < data) |
| max = data; |
| } |
| |
| ctrl->v_level = max >> DP_TRAIN_VOLTAGE_SWING_SHIFT; |
| |
| /* use the max level across lanes */ |
| max = 0; |
| for (i = 0; i < ctrl->lane_cnt; i++) { |
| data = drm_dp_get_adjust_request_pre_emphasis(link_status, i); |
| DBG("lane=%d req_pre_emphasis=0x%x", i, data); |
| if (max < data) |
| max = data; |
| } |
| |
| ctrl->p_level = max >> DP_TRAIN_PRE_EMPHASIS_SHIFT; |
| DBG("v_level=%d, p_level=%d", ctrl->v_level, ctrl->p_level); |
| } |
| |
| static void edp_host_train_set(struct edp_ctrl *ctrl, u32 train) |
| { |
| int cnt = 10; |
| u32 data; |
| u32 shift = train - 1; |
| |
| DBG("train=%d", train); |
| |
| edp_state_ctrl(ctrl, EDP_STATE_CTRL_TRAIN_PATTERN_1 << shift); |
| while (--cnt) { |
| data = edp_read(ctrl->base + REG_EDP_MAINLINK_READY); |
| if (data & (EDP_MAINLINK_READY_TRAIN_PATTERN_1_READY << shift)) |
| break; |
| } |
| |
| if (cnt == 0) |
| pr_err("%s: set link_train=%d failed\n", __func__, train); |
| } |
| |
| static const u8 vm_pre_emphasis[4][4] = { |
| {0x03, 0x06, 0x09, 0x0C}, /* pe0, 0 db */ |
| {0x03, 0x06, 0x09, 0xFF}, /* pe1, 3.5 db */ |
| {0x03, 0x06, 0xFF, 0xFF}, /* pe2, 6.0 db */ |
| {0x03, 0xFF, 0xFF, 0xFF} /* pe3, 9.5 db */ |
| }; |
| |
| /* voltage swing, 0.2v and 1.0v are not support */ |
| static const u8 vm_voltage_swing[4][4] = { |
| {0x14, 0x18, 0x1A, 0x1E}, /* sw0, 0.4v */ |
| {0x18, 0x1A, 0x1E, 0xFF}, /* sw1, 0.6 v */ |
| {0x1A, 0x1E, 0xFF, 0xFF}, /* sw1, 0.8 v */ |
| {0x1E, 0xFF, 0xFF, 0xFF} /* sw1, 1.2 v, optional */ |
| }; |
| |
| static int edp_voltage_pre_emphasise_set(struct edp_ctrl *ctrl) |
| { |
| u32 value0; |
| u32 value1; |
| |
| DBG("v=%d p=%d", ctrl->v_level, ctrl->p_level); |
| |
| value0 = vm_pre_emphasis[(int)(ctrl->v_level)][(int)(ctrl->p_level)]; |
| value1 = vm_voltage_swing[(int)(ctrl->v_level)][(int)(ctrl->p_level)]; |
| |
| /* Configure host and panel only if both values are allowed */ |
| if (value0 != 0xFF && value1 != 0xFF) { |
| msm_edp_phy_vm_pe_cfg(ctrl->phy, value0, value1); |
| return edp_lane_set_write(ctrl, ctrl->v_level, ctrl->p_level); |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int edp_start_link_train_1(struct edp_ctrl *ctrl) |
| { |
| u8 link_status[DP_LINK_STATUS_SIZE]; |
| u8 old_v_level; |
| int tries; |
| int ret; |
| int rlen; |
| |
| DBG(""); |
| |
| edp_host_train_set(ctrl, DP_TRAINING_PATTERN_1); |
| ret = edp_voltage_pre_emphasise_set(ctrl); |
| if (ret) |
| return ret; |
| ret = edp_train_pattern_set_write(ctrl, |
| DP_TRAINING_PATTERN_1 | DP_RECOVERED_CLOCK_OUT_EN); |
| if (ret) |
| return ret; |
| |
| tries = 0; |
| old_v_level = ctrl->v_level; |
| while (1) { |
| drm_dp_link_train_clock_recovery_delay(ctrl->dpcd); |
| |
| rlen = drm_dp_dpcd_read_link_status(ctrl->drm_aux, link_status); |
| if (rlen < DP_LINK_STATUS_SIZE) { |
| pr_err("%s: read link status failed\n", __func__); |
| return -ENOLINK; |
| } |
| if (drm_dp_clock_recovery_ok(link_status, ctrl->lane_cnt)) { |
| ret = 0; |
| break; |
| } |
| |
| if (ctrl->v_level == DPCD_LINK_VOLTAGE_MAX) { |
| ret = -1; |
| break; |
| } |
| |
| if (old_v_level == ctrl->v_level) { |
| tries++; |
| if (tries >= 5) { |
| ret = -1; |
| break; |
| } |
| } else { |
| tries = 0; |
| old_v_level = ctrl->v_level; |
| } |
| |
| edp_sink_train_set_adjust(ctrl, link_status); |
| ret = edp_voltage_pre_emphasise_set(ctrl); |
| if (ret) |
| return ret; |
| } |
| |
| return ret; |
| } |
| |
| static int edp_start_link_train_2(struct edp_ctrl *ctrl) |
| { |
| u8 link_status[DP_LINK_STATUS_SIZE]; |
| int tries = 0; |
| int ret; |
| int rlen; |
| |
| DBG(""); |
| |
| edp_host_train_set(ctrl, DP_TRAINING_PATTERN_2); |
| ret = edp_voltage_pre_emphasise_set(ctrl); |
| if (ret) |
| return ret; |
| |
| ret = edp_train_pattern_set_write(ctrl, |
| DP_TRAINING_PATTERN_2 | DP_RECOVERED_CLOCK_OUT_EN); |
| if (ret) |
| return ret; |
| |
| while (1) { |
| drm_dp_link_train_channel_eq_delay(ctrl->dpcd); |
| |
| rlen = drm_dp_dpcd_read_link_status(ctrl->drm_aux, link_status); |
| if (rlen < DP_LINK_STATUS_SIZE) { |
| pr_err("%s: read link status failed\n", __func__); |
| return -ENOLINK; |
| } |
| if (drm_dp_channel_eq_ok(link_status, ctrl->lane_cnt)) { |
| ret = 0; |
| break; |
| } |
| |
| tries++; |
| if (tries > 10) { |
| ret = -1; |
| break; |
| } |
| |
| edp_sink_train_set_adjust(ctrl, link_status); |
| ret = edp_voltage_pre_emphasise_set(ctrl); |
| if (ret) |
| return ret; |
| } |
| |
| return ret; |
| } |
| |
| static int edp_link_rate_down_shift(struct edp_ctrl *ctrl) |
| { |
| u32 prate, lrate, bpp; |
| u8 rate, lane, max_lane; |
| int changed = 0; |
| |
| rate = ctrl->link_rate; |
| lane = ctrl->lane_cnt; |
| max_lane = ctrl->dp_link.num_lanes; |
| |
| bpp = ctrl->color_depth * 3; |
| prate = ctrl->pixel_rate; |
| prate *= bpp; |
| prate /= 8; /* in kByte */ |
| |
| if (rate > DP_LINK_BW_1_62 && rate <= EDP_LINK_BW_MAX) { |
| rate -= 4; /* reduce rate */ |
| changed++; |
| } |
| |
| if (changed) { |
| if (lane >= 1 && lane < max_lane) |
| lane <<= 1; /* increase lane */ |
| |
| lrate = 270000; /* in kHz */ |
| lrate *= rate; |
| lrate /= 10; /* kByte, 10 bits --> 8 bits */ |
| lrate *= lane; |
| |
| DBG("new lrate=%u prate=%u(kHz) rate=%d lane=%d p=%u b=%d", |
| lrate, prate, rate, lane, |
| ctrl->pixel_rate, |
| bpp); |
| |
| if (lrate > prate) { |
| ctrl->link_rate = rate; |
| ctrl->lane_cnt = lane; |
| DBG("new rate=%d %d", rate, lane); |
| return 0; |
| } |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int edp_clear_training_pattern(struct edp_ctrl *ctrl) |
| { |
| int ret; |
| |
| ret = edp_train_pattern_set_write(ctrl, 0); |
| |
| drm_dp_link_train_channel_eq_delay(ctrl->dpcd); |
| |
| return ret; |
| } |
| |
| static int edp_do_link_train(struct edp_ctrl *ctrl) |
| { |
| int ret; |
| struct drm_dp_link dp_link; |
| |
| DBG(""); |
| /* |
| * Set the current link rate and lane cnt to panel. They may have been |
| * adjusted and the values are different from them in DPCD CAP |
| */ |
| dp_link.num_lanes = ctrl->lane_cnt; |
| dp_link.rate = drm_dp_bw_code_to_link_rate(ctrl->link_rate); |
| dp_link.capabilities = ctrl->dp_link.capabilities; |
| if (drm_dp_link_configure(ctrl->drm_aux, &dp_link) < 0) |
| return EDP_TRAIN_FAIL; |
| |
| ctrl->v_level = 0; /* start from default level */ |
| ctrl->p_level = 0; |
| |
| edp_state_ctrl(ctrl, 0); |
| if (edp_clear_training_pattern(ctrl)) |
| return EDP_TRAIN_FAIL; |
| |
| ret = edp_start_link_train_1(ctrl); |
| if (ret < 0) { |
| if (edp_link_rate_down_shift(ctrl) == 0) { |
| DBG("link reconfig"); |
| ret = EDP_TRAIN_RECONFIG; |
| goto clear; |
| } else { |
| pr_err("%s: Training 1 failed", __func__); |
| ret = EDP_TRAIN_FAIL; |
| goto clear; |
| } |
| } |
| DBG("Training 1 completed successfully"); |
| |
| edp_state_ctrl(ctrl, 0); |
| if (edp_clear_training_pattern(ctrl)) |
| return EDP_TRAIN_FAIL; |
| |
| ret = edp_start_link_train_2(ctrl); |
| if (ret < 0) { |
| if (edp_link_rate_down_shift(ctrl) == 0) { |
| DBG("link reconfig"); |
| ret = EDP_TRAIN_RECONFIG; |
| goto clear; |
| } else { |
| pr_err("%s: Training 2 failed", __func__); |
| ret = EDP_TRAIN_FAIL; |
| goto clear; |
| } |
| } |
| DBG("Training 2 completed successfully"); |
| |
| edp_state_ctrl(ctrl, EDP_STATE_CTRL_SEND_VIDEO); |
| clear: |
| edp_clear_training_pattern(ctrl); |
| |
| return ret; |
| } |
| |
| static void edp_clock_synchrous(struct edp_ctrl *ctrl, int sync) |
| { |
| u32 data; |
| enum edp_color_depth depth; |
| |
| data = edp_read(ctrl->base + REG_EDP_MISC1_MISC0); |
| |
| if (sync) |
| data |= EDP_MISC1_MISC0_SYNC; |
| else |
| data &= ~EDP_MISC1_MISC0_SYNC; |
| |
| /* only legacy rgb mode supported */ |
| depth = EDP_6BIT; /* Default */ |
| if (ctrl->color_depth == 8) |
| depth = EDP_8BIT; |
| else if (ctrl->color_depth == 10) |
| depth = EDP_10BIT; |
| else if (ctrl->color_depth == 12) |
| depth = EDP_12BIT; |
| else if (ctrl->color_depth == 16) |
| depth = EDP_16BIT; |
| |
| data |= EDP_MISC1_MISC0_COLOR(depth); |
| |
| edp_write(ctrl->base + REG_EDP_MISC1_MISC0, data); |
| } |
| |
| static int edp_sw_mvid_nvid(struct edp_ctrl *ctrl, u32 m, u32 n) |
| { |
| u32 n_multi, m_multi = 5; |
| |
| if (ctrl->link_rate == DP_LINK_BW_1_62) { |
| n_multi = 1; |
| } else if (ctrl->link_rate == DP_LINK_BW_2_7) { |
| n_multi = 2; |
| } else { |
| pr_err("%s: Invalid link rate, %d\n", __func__, |
| ctrl->link_rate); |
| return -EINVAL; |
| } |
| |
| edp_write(ctrl->base + REG_EDP_SOFTWARE_MVID, m * m_multi); |
| edp_write(ctrl->base + REG_EDP_SOFTWARE_NVID, n * n_multi); |
| |
| return 0; |
| } |
| |
| static void edp_mainlink_ctrl(struct edp_ctrl *ctrl, int enable) |
| { |
| u32 data = 0; |
| |
| edp_write(ctrl->base + REG_EDP_MAINLINK_CTRL, EDP_MAINLINK_CTRL_RESET); |
| /* Make sure fully reset */ |
| wmb(); |
| usleep_range(500, 1000); |
| |
| if (enable) |
| data |= EDP_MAINLINK_CTRL_ENABLE; |
| |
| edp_write(ctrl->base + REG_EDP_MAINLINK_CTRL, data); |
| } |
| |
| static void edp_ctrl_phy_aux_enable(struct edp_ctrl *ctrl, int enable) |
| { |
| if (enable) { |
| edp_regulator_enable(ctrl); |
| edp_clk_enable(ctrl, EDP_CLK_MASK_AUX_CHAN); |
| msm_edp_phy_ctrl(ctrl->phy, 1); |
| msm_edp_aux_ctrl(ctrl->aux, 1); |
| gpiod_set_value(ctrl->panel_en_gpio, 1); |
| } else { |
| gpiod_set_value(ctrl->panel_en_gpio, 0); |
| msm_edp_aux_ctrl(ctrl->aux, 0); |
| msm_edp_phy_ctrl(ctrl->phy, 0); |
| edp_clk_disable(ctrl, EDP_CLK_MASK_AUX_CHAN); |
| edp_regulator_disable(ctrl); |
| } |
| } |
| |
| static void edp_ctrl_link_enable(struct edp_ctrl *ctrl, int enable) |
| { |
| u32 m, n; |
| |
| if (enable) { |
| /* Enable link channel clocks */ |
| edp_clk_enable(ctrl, EDP_CLK_MASK_LINK_CHAN); |
| |
| msm_edp_phy_lane_power_ctrl(ctrl->phy, true, ctrl->lane_cnt); |
| |
| msm_edp_phy_vm_pe_init(ctrl->phy); |
| |
| /* Make sure phy is programed */ |
| wmb(); |
| msm_edp_phy_ready(ctrl->phy); |
| |
| edp_config_ctrl(ctrl); |
| msm_edp_ctrl_pixel_clock_valid(ctrl, ctrl->pixel_rate, &m, &n); |
| edp_sw_mvid_nvid(ctrl, m, n); |
| edp_mainlink_ctrl(ctrl, 1); |
| } else { |
| edp_mainlink_ctrl(ctrl, 0); |
| |
| msm_edp_phy_lane_power_ctrl(ctrl->phy, false, 0); |
| edp_clk_disable(ctrl, EDP_CLK_MASK_LINK_CHAN); |
| } |
| } |
| |
| static int edp_ctrl_training(struct edp_ctrl *ctrl) |
| { |
| int ret; |
| |
| /* Do link training only when power is on */ |
| if (!ctrl->power_on) |
| return -EINVAL; |
| |
| train_start: |
| ret = edp_do_link_train(ctrl); |
| if (ret == EDP_TRAIN_RECONFIG) { |
| /* Re-configure main link */ |
| edp_ctrl_irq_enable(ctrl, 0); |
| edp_ctrl_link_enable(ctrl, 0); |
| msm_edp_phy_ctrl(ctrl->phy, 0); |
| |
| /* Make sure link is fully disabled */ |
| wmb(); |
| usleep_range(500, 1000); |
| |
| msm_edp_phy_ctrl(ctrl->phy, 1); |
| edp_ctrl_link_enable(ctrl, 1); |
| edp_ctrl_irq_enable(ctrl, 1); |
| goto train_start; |
| } |
| |
| return ret; |
| } |
| |
| static void edp_ctrl_on_worker(struct work_struct *work) |
| { |
| struct edp_ctrl *ctrl = container_of( |
| work, struct edp_ctrl, on_work); |
| int ret; |
| |
| mutex_lock(&ctrl->dev_mutex); |
| |
| if (ctrl->power_on) { |
| DBG("already on"); |
| goto unlock_ret; |
| } |
| |
| edp_ctrl_phy_aux_enable(ctrl, 1); |
| edp_ctrl_link_enable(ctrl, 1); |
| |
| edp_ctrl_irq_enable(ctrl, 1); |
| ret = drm_dp_link_power_up(ctrl->drm_aux, &ctrl->dp_link); |
| if (ret) |
| goto fail; |
| |
| ctrl->power_on = true; |
| |
| /* Start link training */ |
| ret = edp_ctrl_training(ctrl); |
| if (ret != EDP_TRAIN_SUCCESS) |
| goto fail; |
| |
| DBG("DONE"); |
| goto unlock_ret; |
| |
| fail: |
| edp_ctrl_irq_enable(ctrl, 0); |
| edp_ctrl_link_enable(ctrl, 0); |
| edp_ctrl_phy_aux_enable(ctrl, 0); |
| ctrl->power_on = false; |
| unlock_ret: |
| mutex_unlock(&ctrl->dev_mutex); |
| } |
| |
| static void edp_ctrl_off_worker(struct work_struct *work) |
| { |
| struct edp_ctrl *ctrl = container_of( |
| work, struct edp_ctrl, off_work); |
| int ret; |
| |
| mutex_lock(&ctrl->dev_mutex); |
| |
| if (!ctrl->power_on) { |
| DBG("already off"); |
| goto unlock_ret; |
| } |
| |
| reinit_completion(&ctrl->idle_comp); |
| edp_state_ctrl(ctrl, EDP_STATE_CTRL_PUSH_IDLE); |
| |
| ret = wait_for_completion_timeout(&ctrl->idle_comp, |
| msecs_to_jiffies(500)); |
| if (ret <= 0) |
| DBG("%s: idle pattern timedout, %d\n", |
| __func__, ret); |
| |
| edp_state_ctrl(ctrl, 0); |
| |
| drm_dp_link_power_down(ctrl->drm_aux, &ctrl->dp_link); |
| |
| edp_ctrl_irq_enable(ctrl, 0); |
| |
| edp_ctrl_link_enable(ctrl, 0); |
| |
| edp_ctrl_phy_aux_enable(ctrl, 0); |
| |
| ctrl->power_on = false; |
| |
| unlock_ret: |
| mutex_unlock(&ctrl->dev_mutex); |
| } |
| |
| irqreturn_t msm_edp_ctrl_irq(struct edp_ctrl *ctrl) |
| { |
| u32 isr1, isr2, mask1, mask2; |
| u32 ack; |
| |
| DBG(""); |
| spin_lock(&ctrl->irq_lock); |
| isr1 = edp_read(ctrl->base + REG_EDP_INTERRUPT_REG_1); |
| isr2 = edp_read(ctrl->base + REG_EDP_INTERRUPT_REG_2); |
| |
| mask1 = isr1 & EDP_INTR_MASK1; |
| mask2 = isr2 & EDP_INTR_MASK2; |
| |
| isr1 &= ~mask1; /* remove masks bit */ |
| isr2 &= ~mask2; |
| |
| DBG("isr=%x mask=%x isr2=%x mask2=%x", |
| isr1, mask1, isr2, mask2); |
| |
| ack = isr1 & EDP_INTR_STATUS1; |
| ack <<= 1; /* ack bits */ |
| ack |= mask1; |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_1, ack); |
| |
| ack = isr2 & EDP_INTR_STATUS2; |
| ack <<= 1; /* ack bits */ |
| ack |= mask2; |
| edp_write(ctrl->base + REG_EDP_INTERRUPT_REG_2, ack); |
| spin_unlock(&ctrl->irq_lock); |
| |
| if (isr1 & EDP_INTERRUPT_REG_1_HPD) |
| DBG("edp_hpd"); |
| |
| if (isr2 & EDP_INTERRUPT_REG_2_READY_FOR_VIDEO) |
| DBG("edp_video_ready"); |
| |
| if (isr2 & EDP_INTERRUPT_REG_2_IDLE_PATTERNs_SENT) { |
| DBG("idle_patterns_sent"); |
| complete(&ctrl->idle_comp); |
| } |
| |
| msm_edp_aux_irq(ctrl->aux, isr1); |
| |
| return IRQ_HANDLED; |
| } |
| |
| void msm_edp_ctrl_power(struct edp_ctrl *ctrl, bool on) |
| { |
| if (on) |
| queue_work(ctrl->workqueue, &ctrl->on_work); |
| else |
| queue_work(ctrl->workqueue, &ctrl->off_work); |
| } |
| |
| int msm_edp_ctrl_init(struct msm_edp *edp) |
| { |
| struct edp_ctrl *ctrl = NULL; |
| struct device *dev = &edp->pdev->dev; |
| int ret; |
| |
| if (!edp) { |
| pr_err("%s: edp is NULL!\n", __func__); |
| return -EINVAL; |
| } |
| |
| ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL); |
| if (!ctrl) |
| return -ENOMEM; |
| |
| edp->ctrl = ctrl; |
| ctrl->pdev = edp->pdev; |
| |
| ctrl->base = msm_ioremap(ctrl->pdev, "edp", "eDP"); |
| if (IS_ERR(ctrl->base)) |
| return PTR_ERR(ctrl->base); |
| |
| /* Get regulator, clock, gpio, pwm */ |
| ret = edp_regulator_init(ctrl); |
| if (ret) { |
| pr_err("%s:regulator init fail\n", __func__); |
| return ret; |
| } |
| ret = edp_clk_init(ctrl); |
| if (ret) { |
| pr_err("%s:clk init fail\n", __func__); |
| return ret; |
| } |
| ret = edp_gpio_config(ctrl); |
| if (ret) { |
| pr_err("%s:failed to configure GPIOs: %d", __func__, ret); |
| return ret; |
| } |
| |
| /* Init aux and phy */ |
| ctrl->aux = msm_edp_aux_init(dev, ctrl->base, &ctrl->drm_aux); |
| if (!ctrl->aux || !ctrl->drm_aux) { |
| pr_err("%s:failed to init aux\n", __func__); |
| return -ENOMEM; |
| } |
| |
| ctrl->phy = msm_edp_phy_init(dev, ctrl->base); |
| if (!ctrl->phy) { |
| pr_err("%s:failed to init phy\n", __func__); |
| ret = -ENOMEM; |
| goto err_destory_aux; |
| } |
| |
| spin_lock_init(&ctrl->irq_lock); |
| mutex_init(&ctrl->dev_mutex); |
| init_completion(&ctrl->idle_comp); |
| |
| /* setup workqueue */ |
| ctrl->workqueue = alloc_ordered_workqueue("edp_drm_work", 0); |
| INIT_WORK(&ctrl->on_work, edp_ctrl_on_worker); |
| INIT_WORK(&ctrl->off_work, edp_ctrl_off_worker); |
| |
| return 0; |
| |
| err_destory_aux: |
| msm_edp_aux_destroy(dev, ctrl->aux); |
| ctrl->aux = NULL; |
| return ret; |
| } |
| |
| void msm_edp_ctrl_destroy(struct edp_ctrl *ctrl) |
| { |
| if (!ctrl) |
| return; |
| |
| if (ctrl->workqueue) { |
| flush_workqueue(ctrl->workqueue); |
| destroy_workqueue(ctrl->workqueue); |
| ctrl->workqueue = NULL; |
| } |
| |
| if (ctrl->aux) { |
| msm_edp_aux_destroy(&ctrl->pdev->dev, ctrl->aux); |
| ctrl->aux = NULL; |
| } |
| |
| kfree(ctrl->edid); |
| ctrl->edid = NULL; |
| |
| mutex_destroy(&ctrl->dev_mutex); |
| } |
| |
| bool msm_edp_ctrl_panel_connected(struct edp_ctrl *ctrl) |
| { |
| mutex_lock(&ctrl->dev_mutex); |
| DBG("connect status = %d", ctrl->edp_connected); |
| if (ctrl->edp_connected) { |
| mutex_unlock(&ctrl->dev_mutex); |
| return true; |
| } |
| |
| if (!ctrl->power_on) { |
| edp_ctrl_phy_aux_enable(ctrl, 1); |
| edp_ctrl_irq_enable(ctrl, 1); |
| } |
| |
| if (drm_dp_dpcd_read(ctrl->drm_aux, DP_DPCD_REV, ctrl->dpcd, |
| DP_RECEIVER_CAP_SIZE) < DP_RECEIVER_CAP_SIZE) { |
| pr_err("%s: AUX channel is NOT ready\n", __func__); |
| memset(ctrl->dpcd, 0, DP_RECEIVER_CAP_SIZE); |
| } else { |
| ctrl->edp_connected = true; |
| } |
| |
| if (!ctrl->power_on) { |
| edp_ctrl_irq_enable(ctrl, 0); |
| edp_ctrl_phy_aux_enable(ctrl, 0); |
| } |
| |
| DBG("exit: connect status=%d", ctrl->edp_connected); |
| |
| mutex_unlock(&ctrl->dev_mutex); |
| |
| return ctrl->edp_connected; |
| } |
| |
| int msm_edp_ctrl_get_panel_info(struct edp_ctrl *ctrl, |
| struct drm_connector *connector, struct edid **edid) |
| { |
| int ret = 0; |
| |
| mutex_lock(&ctrl->dev_mutex); |
| |
| if (ctrl->edid) { |
| if (edid) { |
| DBG("Just return edid buffer"); |
| *edid = ctrl->edid; |
| } |
| goto unlock_ret; |
| } |
| |
| if (!ctrl->power_on) { |
| edp_ctrl_phy_aux_enable(ctrl, 1); |
| edp_ctrl_irq_enable(ctrl, 1); |
| } |
| |
| ret = drm_dp_link_probe(ctrl->drm_aux, &ctrl->dp_link); |
| if (ret) { |
| pr_err("%s: read dpcd cap failed, %d\n", __func__, ret); |
| goto disable_ret; |
| } |
| |
| /* Initialize link rate as panel max link rate */ |
| ctrl->link_rate = drm_dp_link_rate_to_bw_code(ctrl->dp_link.rate); |
| |
| ctrl->edid = drm_get_edid(connector, &ctrl->drm_aux->ddc); |
| if (!ctrl->edid) { |
| pr_err("%s: edid read fail\n", __func__); |
| goto disable_ret; |
| } |
| |
| if (edid) |
| *edid = ctrl->edid; |
| |
| disable_ret: |
| if (!ctrl->power_on) { |
| edp_ctrl_irq_enable(ctrl, 0); |
| edp_ctrl_phy_aux_enable(ctrl, 0); |
| } |
| unlock_ret: |
| mutex_unlock(&ctrl->dev_mutex); |
| return ret; |
| } |
| |
| int msm_edp_ctrl_timing_cfg(struct edp_ctrl *ctrl, |
| const struct drm_display_mode *mode, |
| const struct drm_display_info *info) |
| { |
| u32 hstart_from_sync, vstart_from_sync; |
| u32 data; |
| int ret = 0; |
| |
| mutex_lock(&ctrl->dev_mutex); |
| /* |
| * Need to keep color depth, pixel rate and |
| * interlaced information in ctrl context |
| */ |
| ctrl->color_depth = info->bpc; |
| ctrl->pixel_rate = mode->clock; |
| ctrl->interlaced = !!(mode->flags & DRM_MODE_FLAG_INTERLACE); |
| |
| /* Fill initial link config based on passed in timing */ |
| edp_fill_link_cfg(ctrl); |
| |
| if (edp_clk_enable(ctrl, EDP_CLK_MASK_AHB)) { |
| pr_err("%s, fail to prepare enable ahb clk\n", __func__); |
| ret = -EINVAL; |
| goto unlock_ret; |
| } |
| edp_clock_synchrous(ctrl, 1); |
| |
| /* Configure eDP timing to HW */ |
| edp_write(ctrl->base + REG_EDP_TOTAL_HOR_VER, |
| EDP_TOTAL_HOR_VER_HORIZ(mode->htotal) | |
| EDP_TOTAL_HOR_VER_VERT(mode->vtotal)); |
| |
| vstart_from_sync = mode->vtotal - mode->vsync_start; |
| hstart_from_sync = mode->htotal - mode->hsync_start; |
| edp_write(ctrl->base + REG_EDP_START_HOR_VER_FROM_SYNC, |
| EDP_START_HOR_VER_FROM_SYNC_HORIZ(hstart_from_sync) | |
| EDP_START_HOR_VER_FROM_SYNC_VERT(vstart_from_sync)); |
| |
| data = EDP_HSYNC_VSYNC_WIDTH_POLARITY_VERT( |
| mode->vsync_end - mode->vsync_start); |
| data |= EDP_HSYNC_VSYNC_WIDTH_POLARITY_HORIZ( |
| mode->hsync_end - mode->hsync_start); |
| if (mode->flags & DRM_MODE_FLAG_NVSYNC) |
| data |= EDP_HSYNC_VSYNC_WIDTH_POLARITY_NVSYNC; |
| if (mode->flags & DRM_MODE_FLAG_NHSYNC) |
| data |= EDP_HSYNC_VSYNC_WIDTH_POLARITY_NHSYNC; |
| edp_write(ctrl->base + REG_EDP_HSYNC_VSYNC_WIDTH_POLARITY, data); |
| |
| edp_write(ctrl->base + REG_EDP_ACTIVE_HOR_VER, |
| EDP_ACTIVE_HOR_VER_HORIZ(mode->hdisplay) | |
| EDP_ACTIVE_HOR_VER_VERT(mode->vdisplay)); |
| |
| edp_clk_disable(ctrl, EDP_CLK_MASK_AHB); |
| |
| unlock_ret: |
| mutex_unlock(&ctrl->dev_mutex); |
| return ret; |
| } |
| |
| bool msm_edp_ctrl_pixel_clock_valid(struct edp_ctrl *ctrl, |
| u32 pixel_rate, u32 *pm, u32 *pn) |
| { |
| const struct edp_pixel_clk_div *divs; |
| u32 err = 1; /* 1% error tolerance */ |
| u32 clk_err; |
| int i; |
| |
| if (ctrl->link_rate == DP_LINK_BW_1_62) { |
| divs = clk_divs[0]; |
| } else if (ctrl->link_rate == DP_LINK_BW_2_7) { |
| divs = clk_divs[1]; |
| } else { |
| pr_err("%s: Invalid link rate,%d\n", __func__, ctrl->link_rate); |
| return false; |
| } |
| |
| for (i = 0; i < EDP_PIXEL_CLK_NUM; i++) { |
| clk_err = abs(divs[i].rate - pixel_rate); |
| if ((divs[i].rate * err / 100) >= clk_err) { |
| if (pm) |
| *pm = divs[i].m; |
| if (pn) |
| *pn = divs[i].n; |
| return true; |
| } |
| } |
| |
| DBG("pixel clock %d(kHz) not supported", pixel_rate); |
| |
| return false; |
| } |
| |