| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (c) 2016-2019, The Linux Foundation. All rights reserved. |
| */ |
| |
| #define pr_fmt(fmt) "[dp-pll] %s: " fmt, __func__ |
| |
| #include <linux/kernel.h> |
| #include <linux/err.h> |
| #include <linux/iopoll.h> |
| #include <linux/delay.h> |
| #include <linux/usb/usbpd.h> |
| |
| #include "mdss-pll.h" |
| #include "mdss-dp-pll.h" |
| #include "mdss-dp-pll-7nm.h" |
| |
| #define DP_PHY_CFG 0x0010 |
| #define DP_PHY_PD_CTL 0x0018 |
| #define DP_PHY_MODE 0x001C |
| |
| #define DP_PHY_AUX_CFG1 0x0024 |
| #define DP_PHY_AUX_CFG2 0x0028 |
| |
| #define DP_PHY_VCO_DIV 0x0070 |
| #define DP_PHY_TX0_TX1_LANE_CTL 0x0078 |
| #define DP_PHY_TX2_TX3_LANE_CTL 0x009C |
| |
| #define DP_PHY_SPARE0 0x00C8 |
| #define DP_PHY_STATUS 0x00DC |
| |
| /* Tx registers */ |
| #define TXn_CLKBUF_ENABLE 0x0008 |
| #define TXn_TX_EMP_POST1_LVL 0x000C |
| |
| #define TXn_TX_DRV_LVL 0x0014 |
| |
| #define TXn_RESET_TSYNC_EN 0x001C |
| #define TXn_PRE_STALL_LDO_BOOST_EN 0x0020 |
| #define TXn_TX_BAND 0x0024 |
| #define TXn_INTERFACE_SELECT 0x002C |
| |
| #define TXn_RES_CODE_LANE_OFFSET_TX 0x003C |
| #define TXn_RES_CODE_LANE_OFFSET_RX 0x0040 |
| |
| #define TXn_TRANSCEIVER_BIAS_EN 0x0054 |
| #define TXn_HIGHZ_DRVR_EN 0x0058 |
| #define TXn_TX_POL_INV 0x005C |
| #define TXn_PARRATE_REC_DETECT_IDLE_EN 0x0060 |
| |
| #define TXn_TRAN_DRVR_EMP_EN 0x00B8 |
| #define TXn_TX_INTERFACE_MODE 0x00BC |
| |
| #define TXn_VMODE_CTRL1 0x00E8 |
| |
| /* PLL register offset */ |
| #define QSERDES_COM_BG_TIMER 0x000C |
| #define QSERDES_COM_BIAS_EN_CLKBUFLR_EN 0x0044 |
| #define QSERDES_COM_CLK_ENABLE1 0x0048 |
| #define QSERDES_COM_SYS_CLK_CTRL 0x004C |
| #define QSERDES_COM_SYSCLK_BUF_ENABLE 0x0050 |
| #define QSERDES_COM_PLL_IVCO 0x0058 |
| |
| #define QSERDES_COM_CP_CTRL_MODE0 0x0074 |
| #define QSERDES_COM_PLL_RCTRL_MODE0 0x007C |
| #define QSERDES_COM_PLL_CCTRL_MODE0 0x0084 |
| #define QSERDES_COM_SYSCLK_EN_SEL 0x0094 |
| #define QSERDES_COM_RESETSM_CNTRL 0x009C |
| #define QSERDES_COM_LOCK_CMP_EN 0x00A4 |
| #define QSERDES_COM_LOCK_CMP1_MODE0 0x00AC |
| #define QSERDES_COM_LOCK_CMP2_MODE0 0x00B0 |
| |
| #define QSERDES_COM_DEC_START_MODE0 0x00BC |
| #define QSERDES_COM_DIV_FRAC_START1_MODE0 0x00CC |
| #define QSERDES_COM_DIV_FRAC_START2_MODE0 0x00D0 |
| #define QSERDES_COM_DIV_FRAC_START3_MODE0 0x00D4 |
| #define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 0x00EC |
| #define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 0x00F0 |
| #define QSERDES_COM_VCO_TUNE_CTRL 0x0108 |
| #define QSERDES_COM_VCO_TUNE_MAP 0x010C |
| |
| #define QSERDES_COM_CLK_SEL 0x0154 |
| #define QSERDES_COM_HSCLK_SEL 0x0158 |
| |
| #define QSERDES_COM_CORECLK_DIV_MODE0 0x0168 |
| |
| #define QSERDES_COM_CORE_CLK_EN 0x0174 |
| #define QSERDES_COM_C_READY_STATUS 0x0178 |
| #define QSERDES_COM_CMN_CONFIG 0x017C |
| |
| #define QSERDES_COM_SVS_MODE_CLK_SEL 0x0184 |
| |
| #define DP_PHY_PLL_POLL_SLEEP_US 500 |
| #define DP_PHY_PLL_POLL_TIMEOUT_US 10000 |
| |
| #define DP_VCO_RATE_8100MHZDIV1000 8100000UL |
| #define DP_VCO_RATE_9720MHZDIV1000 9720000UL |
| #define DP_VCO_RATE_10800MHZDIV1000 10800000UL |
| |
| int dp_mux_set_parent_7nm(void *context, unsigned int reg, unsigned int val) |
| { |
| struct mdss_pll_resources *dp_res = context; |
| int rc; |
| u32 auxclk_div; |
| |
| if (!context) { |
| pr_err("invalid input parameters\n"); |
| return -EINVAL; |
| } |
| |
| rc = mdss_pll_resource_enable(dp_res, true); |
| if (rc) { |
| pr_err("Failed to enable mdss DP PLL resources\n"); |
| return rc; |
| } |
| |
| auxclk_div = MDSS_PLL_REG_R(dp_res->phy_base, DP_PHY_VCO_DIV); |
| auxclk_div &= ~0x03; |
| |
| if (val == 0) |
| auxclk_div |= 1; |
| else if (val == 1) |
| auxclk_div |= 2; |
| else if (val == 2) |
| auxclk_div |= 0; |
| |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_VCO_DIV, auxclk_div); |
| /* Make sure the PHY registers writes are done */ |
| wmb(); |
| pr_debug("mux=%d auxclk_div=%x\n", val, auxclk_div); |
| |
| mdss_pll_resource_enable(dp_res, false); |
| |
| return 0; |
| } |
| |
| int dp_mux_get_parent_7nm(void *context, unsigned int reg, unsigned int *val) |
| { |
| int rc; |
| u32 auxclk_div = 0; |
| struct mdss_pll_resources *dp_res = context; |
| |
| if (!context || !val) { |
| pr_err("invalid input parameters\n"); |
| return -EINVAL; |
| } |
| |
| if (is_gdsc_disabled(dp_res)) |
| return 0; |
| |
| rc = mdss_pll_resource_enable(dp_res, true); |
| if (rc) { |
| pr_err("Failed to enable dp_res resources\n"); |
| return rc; |
| } |
| |
| auxclk_div = MDSS_PLL_REG_R(dp_res->phy_base, DP_PHY_VCO_DIV); |
| auxclk_div &= 0x03; |
| |
| if (auxclk_div == 1) /* Default divider */ |
| *val = 0; |
| else if (auxclk_div == 2) |
| *val = 1; |
| else if (auxclk_div == 0) |
| *val = 2; |
| |
| mdss_pll_resource_enable(dp_res, false); |
| |
| pr_debug("auxclk_div=%d, val=%d\n", auxclk_div, *val); |
| |
| return 0; |
| } |
| |
| static int dp_vco_pll_init_db_7nm(struct dp_pll_db_7nm *pdb, |
| unsigned long rate) |
| { |
| struct mdss_pll_resources *dp_res = pdb->pll; |
| u32 spare_value = 0; |
| |
| spare_value = MDSS_PLL_REG_R(dp_res->phy_base, DP_PHY_SPARE0); |
| pdb->lane_cnt = spare_value & 0x0F; |
| pdb->orientation = (spare_value & 0xF0) >> 4; |
| |
| pr_debug("spare_value=0x%x, ln_cnt=0x%x, orientation=0x%x\n", |
| spare_value, pdb->lane_cnt, pdb->orientation); |
| |
| pdb->div_frac_start1_mode0 = 0x00; |
| pdb->integloop_gain0_mode0 = 0x3f; |
| pdb->integloop_gain1_mode0 = 0x00; |
| pdb->vco_tune_map = 0x00; |
| pdb->cmn_config = 0x02; |
| pdb->txn_tran_drv_emp_en = 0xf; |
| |
| switch (rate) { |
| case DP_VCO_HSCLK_RATE_1620MHZDIV1000: |
| pr_debug("VCO rate: %ld\n", DP_VCO_RATE_9720MHZDIV1000); |
| pdb->hsclk_sel = 0x05; |
| pdb->dec_start_mode0 = 0x69; |
| pdb->div_frac_start2_mode0 = 0x80; |
| pdb->div_frac_start3_mode0 = 0x07; |
| pdb->lock_cmp1_mode0 = 0x6f; |
| pdb->lock_cmp2_mode0 = 0x08; |
| pdb->phy_vco_div = 0x1; |
| pdb->lock_cmp_en = 0x04; |
| break; |
| case DP_VCO_HSCLK_RATE_2700MHZDIV1000: |
| pr_debug("VCO rate: %ld\n", DP_VCO_RATE_10800MHZDIV1000); |
| pdb->hsclk_sel = 0x03; |
| pdb->dec_start_mode0 = 0x69; |
| pdb->div_frac_start2_mode0 = 0x80; |
| pdb->div_frac_start3_mode0 = 0x07; |
| pdb->lock_cmp1_mode0 = 0x0f; |
| pdb->lock_cmp2_mode0 = 0x0e; |
| pdb->phy_vco_div = 0x1; |
| pdb->lock_cmp_en = 0x08; |
| break; |
| case DP_VCO_HSCLK_RATE_5400MHZDIV1000: |
| pr_debug("VCO rate: %ld\n", DP_VCO_RATE_10800MHZDIV1000); |
| pdb->hsclk_sel = 0x01; |
| pdb->dec_start_mode0 = 0x8c; |
| pdb->div_frac_start2_mode0 = 0x00; |
| pdb->div_frac_start3_mode0 = 0x0a; |
| pdb->lock_cmp1_mode0 = 0x1f; |
| pdb->lock_cmp2_mode0 = 0x1c; |
| pdb->phy_vco_div = 0x2; |
| pdb->lock_cmp_en = 0x08; |
| break; |
| case DP_VCO_HSCLK_RATE_8100MHZDIV1000: |
| pr_debug("VCO rate: %ld\n", DP_VCO_RATE_8100MHZDIV1000); |
| pdb->hsclk_sel = 0x00; |
| pdb->dec_start_mode0 = 0x69; |
| pdb->div_frac_start2_mode0 = 0x80; |
| pdb->div_frac_start3_mode0 = 0x07; |
| pdb->lock_cmp1_mode0 = 0x2f; |
| pdb->lock_cmp2_mode0 = 0x2a; |
| pdb->phy_vco_div = 0x0; |
| pdb->lock_cmp_en = 0x08; |
| break; |
| default: |
| pr_err("unsupported rate %ld\n", rate); |
| return -EINVAL; |
| } |
| return 0; |
| } |
| |
| static int dp_config_vco_rate_7nm(struct dp_pll_vco_clk *vco, |
| unsigned long rate) |
| { |
| u32 res = 0; |
| struct mdss_pll_resources *dp_res = vco->priv; |
| struct dp_pll_db_7nm *pdb = (struct dp_pll_db_7nm *)dp_res->priv; |
| |
| res = dp_vco_pll_init_db_7nm(pdb, rate); |
| if (res) { |
| pr_err("VCO Init DB failed\n"); |
| return res; |
| } |
| |
| if (pdb->lane_cnt != 4) { |
| if (pdb->orientation == ORIENTATION_CC2) |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_PD_CTL, 0x6d); |
| else |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_PD_CTL, 0x75); |
| } else { |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_PD_CTL, 0x7d); |
| } |
| |
| /* Make sure the PHY register writes are done */ |
| wmb(); |
| |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_SVS_MODE_CLK_SEL, 0x05); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_SYSCLK_EN_SEL, 0x3b); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_SYS_CLK_CTRL, 0x02); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_CLK_ENABLE1, 0x0c); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_SYSCLK_BUF_ENABLE, 0x06); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_CLK_SEL, 0x30); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_HSCLK_SEL, pdb->hsclk_sel); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_PLL_IVCO, 0x0f); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_LOCK_CMP_EN, pdb->lock_cmp_en); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_PLL_CCTRL_MODE0, 0x36); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_PLL_RCTRL_MODE0, 0x16); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_CP_CTRL_MODE0, 0x06); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_DEC_START_MODE0, pdb->dec_start_mode0); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_DIV_FRAC_START1_MODE0, pdb->div_frac_start1_mode0); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_DIV_FRAC_START2_MODE0, pdb->div_frac_start2_mode0); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_DIV_FRAC_START3_MODE0, pdb->div_frac_start3_mode0); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_CMN_CONFIG, pdb->cmn_config); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_INTEGLOOP_GAIN0_MODE0, pdb->integloop_gain0_mode0); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_INTEGLOOP_GAIN1_MODE0, pdb->integloop_gain1_mode0); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_VCO_TUNE_MAP, pdb->vco_tune_map); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_LOCK_CMP1_MODE0, pdb->lock_cmp1_mode0); |
| MDSS_PLL_REG_W(dp_res->pll_base, |
| QSERDES_COM_LOCK_CMP2_MODE0, pdb->lock_cmp2_mode0); |
| /* Make sure the PLL register writes are done */ |
| wmb(); |
| |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_BG_TIMER, 0x0a); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_CORECLK_DIV_MODE0, 0x0a); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_VCO_TUNE_CTRL, 0x00); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x17); |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_CORE_CLK_EN, 0x1f); |
| /* Make sure the PHY register writes are done */ |
| wmb(); |
| |
| if (pdb->orientation == ORIENTATION_CC2) |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_MODE, 0x4c); |
| else |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_MODE, 0x5c); |
| /* Make sure the PLL register writes are done */ |
| wmb(); |
| |
| /* TX Lane configuration */ |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_TX0_TX1_LANE_CTL, 0x05); |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_TX2_TX3_LANE_CTL, 0x05); |
| |
| /* TX-0 register configuration */ |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_TRANSCEIVER_BIAS_EN, 0x1a); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_VMODE_CTRL1, 0x40); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_PRE_STALL_LDO_BOOST_EN, 0x30); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_INTERFACE_SELECT, 0x3b); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_CLKBUF_ENABLE, 0x0f); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_RESET_TSYNC_EN, 0x03); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_TRAN_DRVR_EMP_EN, |
| pdb->txn_tran_drv_emp_en); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, |
| TXn_PARRATE_REC_DETECT_IDLE_EN, 0x00); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_TX_INTERFACE_MODE, 0x00); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_TX_BAND, 0x4); |
| |
| /* TX-1 register configuration */ |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_TRANSCEIVER_BIAS_EN, 0x1a); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_VMODE_CTRL1, 0x40); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_PRE_STALL_LDO_BOOST_EN, 0x30); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_INTERFACE_SELECT, 0x3b); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_CLKBUF_ENABLE, 0x0f); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_RESET_TSYNC_EN, 0x03); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_TRAN_DRVR_EMP_EN, |
| pdb->txn_tran_drv_emp_en); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, |
| TXn_PARRATE_REC_DETECT_IDLE_EN, 0x00); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_TX_INTERFACE_MODE, 0x00); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_TX_BAND, 0x4); |
| /* Make sure the PHY register writes are done */ |
| wmb(); |
| |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_VCO_DIV, pdb->phy_vco_div); |
| |
| return res; |
| } |
| |
| static bool dp_7nm_pll_lock_status(struct mdss_pll_resources *dp_res) |
| { |
| u32 status; |
| bool pll_locked; |
| |
| if (readl_poll_timeout_atomic((dp_res->pll_base + |
| QSERDES_COM_C_READY_STATUS), |
| status, |
| ((status & BIT(0)) > 0), |
| DP_PHY_PLL_POLL_SLEEP_US, |
| DP_PHY_PLL_POLL_TIMEOUT_US)) { |
| pr_err("C_READY status is not high. Status=%x\n", status); |
| pll_locked = false; |
| } else { |
| pll_locked = true; |
| } |
| |
| return pll_locked; |
| } |
| |
| static bool dp_7nm_phy_rdy_status(struct mdss_pll_resources *dp_res) |
| { |
| u32 status; |
| bool phy_ready = true; |
| |
| /* poll for PHY ready status */ |
| if (readl_poll_timeout_atomic((dp_res->phy_base + |
| DP_PHY_STATUS), |
| status, |
| ((status & (BIT(1))) > 0), |
| DP_PHY_PLL_POLL_SLEEP_US, |
| DP_PHY_PLL_POLL_TIMEOUT_US)) { |
| pr_err("Phy_ready is not high. Status=%x\n", status); |
| phy_ready = false; |
| } |
| |
| return phy_ready; |
| } |
| |
| static int dp_pll_enable_7nm(struct clk_hw *hw) |
| { |
| int rc = 0; |
| struct dp_pll_vco_clk *vco = to_dp_vco_hw(hw); |
| struct mdss_pll_resources *dp_res = vco->priv; |
| struct dp_pll_db_7nm *pdb = (struct dp_pll_db_7nm *)dp_res->priv; |
| u32 bias_en, drvr_en; |
| |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_AUX_CFG1, 0x13); |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_AUX_CFG2, 0xA4); |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_CFG, 0x01); |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_CFG, 0x05); |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_CFG, 0x01); |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_CFG, 0x09); |
| wmb(); /* Make sure the PHY register writes are done */ |
| |
| MDSS_PLL_REG_W(dp_res->pll_base, QSERDES_COM_RESETSM_CNTRL, 0x20); |
| wmb(); /* Make sure the PLL register writes are done */ |
| |
| if (!dp_7nm_pll_lock_status(dp_res)) { |
| rc = -EINVAL; |
| goto lock_err; |
| } |
| |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_CFG, 0x19); |
| /* Make sure the PHY register writes are done */ |
| wmb(); |
| /* poll for PHY ready status */ |
| if (!dp_7nm_phy_rdy_status(dp_res)) { |
| rc = -EINVAL; |
| goto lock_err; |
| } |
| |
| pr_debug("PLL is locked\n"); |
| |
| if (pdb->lane_cnt == 1) { |
| bias_en = 0x3e; |
| drvr_en = 0x13; |
| } else { |
| bias_en = 0x3f; |
| drvr_en = 0x10; |
| } |
| |
| if (pdb->lane_cnt != 4) { |
| if (pdb->orientation == ORIENTATION_CC1) { |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, |
| TXn_HIGHZ_DRVR_EN, drvr_en); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, |
| TXn_TRANSCEIVER_BIAS_EN, bias_en); |
| } else { |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, |
| TXn_HIGHZ_DRVR_EN, drvr_en); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, |
| TXn_TRANSCEIVER_BIAS_EN, bias_en); |
| } |
| } else { |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_HIGHZ_DRVR_EN, drvr_en); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, |
| TXn_TRANSCEIVER_BIAS_EN, bias_en); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_HIGHZ_DRVR_EN, drvr_en); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, |
| TXn_TRANSCEIVER_BIAS_EN, bias_en); |
| } |
| |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_TX_POL_INV, 0x0a); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_TX_POL_INV, 0x0a); |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_CFG, 0x18); |
| udelay(2000); |
| |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_CFG, 0x19); |
| |
| /* |
| * Make sure all the register writes are completed before |
| * doing any other operation |
| */ |
| wmb(); |
| |
| /* poll for PHY ready status */ |
| if (!dp_7nm_phy_rdy_status(dp_res)) { |
| rc = -EINVAL; |
| goto lock_err; |
| } |
| |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_TX_DRV_LVL, 0x3f); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_TX_DRV_LVL, 0x3f); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_TX_EMP_POST1_LVL, 0x23); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_TX_EMP_POST1_LVL, 0x23); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_RES_CODE_LANE_OFFSET_TX, 0x11); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_RES_CODE_LANE_OFFSET_TX, 0x11); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_RES_CODE_LANE_OFFSET_RX, 0x11); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_RES_CODE_LANE_OFFSET_RX, 0x11); |
| MDSS_PLL_REG_W(dp_res->ln_tx0_base, TXn_INTERFACE_SELECT, 0x3b); |
| MDSS_PLL_REG_W(dp_res->ln_tx1_base, TXn_INTERFACE_SELECT, 0x3b); |
| /* Make sure the PHY register writes are done */ |
| wmb(); |
| |
| lock_err: |
| return rc; |
| } |
| |
| static int dp_pll_disable_7nm(struct clk_hw *hw) |
| { |
| struct dp_pll_vco_clk *vco = to_dp_vco_hw(hw); |
| struct mdss_pll_resources *dp_res = vco->priv; |
| |
| /* Assert DP PHY power down */ |
| MDSS_PLL_REG_W(dp_res->phy_base, DP_PHY_PD_CTL, 0x2); |
| /* |
| * Make sure all the register writes to disable PLL are |
| * completed before doing any other operation |
| */ |
| wmb(); |
| |
| return 0; |
| } |
| |
| int dp_vco_prepare_7nm(struct clk_hw *hw) |
| { |
| int rc = 0; |
| struct dp_pll_vco_clk *vco; |
| struct mdss_pll_resources *dp_res; |
| |
| if (!hw) { |
| pr_err("invalid input parameters\n"); |
| return -EINVAL; |
| } |
| |
| vco = to_dp_vco_hw(hw); |
| dp_res = vco->priv; |
| |
| pr_debug("rate=%ld\n", vco->rate); |
| rc = mdss_pll_resource_enable(dp_res, true); |
| if (rc) { |
| pr_err("Failed to enable mdss DP pll resources\n"); |
| goto error; |
| } |
| |
| if ((dp_res->vco_cached_rate != 0) |
| && (dp_res->vco_cached_rate == vco->rate)) { |
| rc = vco->hw.init->ops->set_rate(hw, |
| dp_res->vco_cached_rate, dp_res->vco_cached_rate); |
| if (rc) { |
| pr_err("index=%d vco_set_rate failed. rc=%d\n", |
| rc, dp_res->index); |
| mdss_pll_resource_enable(dp_res, false); |
| goto error; |
| } |
| } |
| |
| rc = dp_pll_enable_7nm(hw); |
| if (rc) { |
| mdss_pll_resource_enable(dp_res, false); |
| pr_err("ndx=%d failed to enable dp pll\n", dp_res->index); |
| goto error; |
| } |
| |
| mdss_pll_resource_enable(dp_res, false); |
| error: |
| return rc; |
| } |
| |
| void dp_vco_unprepare_7nm(struct clk_hw *hw) |
| { |
| struct dp_pll_vco_clk *vco; |
| struct mdss_pll_resources *dp_res; |
| |
| if (!hw) { |
| pr_err("invalid input parameters\n"); |
| return; |
| } |
| |
| vco = to_dp_vco_hw(hw); |
| dp_res = vco->priv; |
| |
| if (!dp_res) { |
| pr_err("invalid input parameter\n"); |
| return; |
| } |
| |
| if (!dp_res->pll_on && |
| mdss_pll_resource_enable(dp_res, true)) { |
| pr_err("pll resource can't be enabled\n"); |
| return; |
| } |
| dp_res->vco_cached_rate = vco->rate; |
| dp_pll_disable_7nm(hw); |
| |
| dp_res->handoff_resources = false; |
| mdss_pll_resource_enable(dp_res, false); |
| dp_res->pll_on = false; |
| } |
| |
| int dp_vco_set_rate_7nm(struct clk_hw *hw, unsigned long rate, |
| unsigned long parent_rate) |
| { |
| struct dp_pll_vco_clk *vco; |
| struct mdss_pll_resources *dp_res; |
| int rc; |
| |
| if (!hw) { |
| pr_err("invalid input parameters\n"); |
| return -EINVAL; |
| } |
| |
| vco = to_dp_vco_hw(hw); |
| dp_res = vco->priv; |
| |
| rc = mdss_pll_resource_enable(dp_res, true); |
| if (rc) { |
| pr_err("pll resource can't be enabled\n"); |
| return rc; |
| } |
| |
| pr_debug("DP lane CLK rate=%ld\n", rate); |
| |
| rc = dp_config_vco_rate_7nm(vco, rate); |
| if (rc) |
| pr_err("Failed to set clk rate\n"); |
| |
| mdss_pll_resource_enable(dp_res, false); |
| |
| vco->rate = rate; |
| |
| return 0; |
| } |
| |
| unsigned long dp_vco_recalc_rate_7nm(struct clk_hw *hw, |
| unsigned long parent_rate) |
| { |
| struct dp_pll_vco_clk *vco; |
| int rc; |
| u32 hsclk_sel, link_clk_divsel, hsclk_div, link_clk_div = 0; |
| unsigned long vco_rate; |
| struct mdss_pll_resources *dp_res; |
| |
| if (!hw) { |
| pr_err("invalid input parameters\n"); |
| return 0; |
| } |
| |
| vco = to_dp_vco_hw(hw); |
| dp_res = vco->priv; |
| |
| if (is_gdsc_disabled(dp_res)) |
| return 0; |
| |
| rc = mdss_pll_resource_enable(dp_res, true); |
| if (rc) { |
| pr_err("Failed to enable mdss DP pll=%d\n", dp_res->index); |
| return 0; |
| } |
| |
| pr_debug("input rates: parent=%lu, vco=%lu\n", parent_rate, vco->rate); |
| |
| hsclk_sel = MDSS_PLL_REG_R(dp_res->pll_base, QSERDES_COM_HSCLK_SEL); |
| hsclk_sel &= 0x0f; |
| |
| if (hsclk_sel == 5) |
| hsclk_div = 5; |
| else if (hsclk_sel == 3) |
| hsclk_div = 3; |
| else if (hsclk_sel == 1) |
| hsclk_div = 2; |
| else if (hsclk_sel == 0) |
| hsclk_div = 1; |
| else { |
| pr_debug("unknown divider. forcing to default\n"); |
| hsclk_div = 5; |
| } |
| |
| link_clk_divsel = MDSS_PLL_REG_R(dp_res->phy_base, DP_PHY_AUX_CFG2); |
| link_clk_divsel >>= 2; |
| link_clk_divsel &= 0x3; |
| |
| if (link_clk_divsel == 0) |
| link_clk_div = 5; |
| else if (link_clk_divsel == 1) |
| link_clk_div = 10; |
| else if (link_clk_divsel == 2) |
| link_clk_div = 20; |
| else |
| pr_err("unsupported div. Phy_mode: %d\n", link_clk_divsel); |
| |
| if (link_clk_div == 20) { |
| vco_rate = DP_VCO_HSCLK_RATE_2700MHZDIV1000; |
| } else { |
| if (hsclk_div == 5) |
| vco_rate = DP_VCO_HSCLK_RATE_1620MHZDIV1000; |
| else if (hsclk_div == 3) |
| vco_rate = DP_VCO_HSCLK_RATE_2700MHZDIV1000; |
| else if (hsclk_div == 2) |
| vco_rate = DP_VCO_HSCLK_RATE_5400MHZDIV1000; |
| else |
| vco_rate = DP_VCO_HSCLK_RATE_8100MHZDIV1000; |
| } |
| |
| pr_debug("hsclk: sel=0x%x, div=0x%x; lclk: sel=%lu, div=%lu, rate=%lu\n", |
| hsclk_sel, hsclk_div, link_clk_divsel, link_clk_div, vco_rate); |
| |
| mdss_pll_resource_enable(dp_res, false); |
| |
| dp_res->vco_cached_rate = vco->rate = vco_rate; |
| return vco_rate; |
| } |
| |
| long dp_vco_round_rate_7nm(struct clk_hw *hw, unsigned long rate, |
| unsigned long *parent_rate) |
| { |
| unsigned long rrate = rate; |
| struct dp_pll_vco_clk *vco; |
| |
| if (!hw) { |
| pr_err("invalid input parameters\n"); |
| return 0; |
| } |
| |
| vco = to_dp_vco_hw(hw); |
| if (rate <= vco->min_rate) |
| rrate = vco->min_rate; |
| else if (rate <= DP_VCO_HSCLK_RATE_2700MHZDIV1000) |
| rrate = DP_VCO_HSCLK_RATE_2700MHZDIV1000; |
| else if (rate <= DP_VCO_HSCLK_RATE_5400MHZDIV1000) |
| rrate = DP_VCO_HSCLK_RATE_5400MHZDIV1000; |
| else |
| rrate = vco->max_rate; |
| |
| pr_debug("rrate=%ld\n", rrate); |
| |
| if (parent_rate) |
| *parent_rate = rrate; |
| return rrate; |
| } |
| |