| /* |
| * drivers/mtd/nand/gpio.c |
| * |
| * Updated, and converted to generic GPIO based driver by Russell King. |
| * |
| * Written by Ben Dooks <ben@simtec.co.uk> |
| * Based on 2.4 version by Mark Whittaker |
| * |
| * © 2004 Simtec Electronics |
| * |
| * Device driver for NAND connected via GPIO |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| * |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/init.h> |
| #include <linux/slab.h> |
| #include <linux/module.h> |
| #include <linux/platform_device.h> |
| #include <linux/gpio.h> |
| #include <linux/io.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/nand.h> |
| #include <linux/mtd/partitions.h> |
| #include <linux/mtd/nand-gpio.h> |
| #include <linux/of.h> |
| #include <linux/of_address.h> |
| #include <linux/of_gpio.h> |
| |
| struct gpiomtd { |
| void __iomem *io_sync; |
| struct mtd_info mtd_info; |
| struct nand_chip nand_chip; |
| struct gpio_nand_platdata plat; |
| }; |
| |
| #define gpio_nand_getpriv(x) container_of(x, struct gpiomtd, mtd_info) |
| |
| |
| #ifdef CONFIG_ARM |
| /* gpio_nand_dosync() |
| * |
| * Make sure the GPIO state changes occur in-order with writes to NAND |
| * memory region. |
| * Needed on PXA due to bus-reordering within the SoC itself (see section on |
| * I/O ordering in PXA manual (section 2.3, p35) |
| */ |
| static void gpio_nand_dosync(struct gpiomtd *gpiomtd) |
| { |
| unsigned long tmp; |
| |
| if (gpiomtd->io_sync) { |
| /* |
| * Linux memory barriers don't cater for what's required here. |
| * What's required is what's here - a read from a separate |
| * region with a dependency on that read. |
| */ |
| tmp = readl(gpiomtd->io_sync); |
| asm volatile("mov %1, %0\n" : "=r" (tmp) : "r" (tmp)); |
| } |
| } |
| #else |
| static inline void gpio_nand_dosync(struct gpiomtd *gpiomtd) {} |
| #endif |
| |
| static void gpio_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) |
| { |
| struct gpiomtd *gpiomtd = gpio_nand_getpriv(mtd); |
| |
| gpio_nand_dosync(gpiomtd); |
| |
| if (ctrl & NAND_CTRL_CHANGE) { |
| gpio_set_value(gpiomtd->plat.gpio_nce, !(ctrl & NAND_NCE)); |
| gpio_set_value(gpiomtd->plat.gpio_cle, !!(ctrl & NAND_CLE)); |
| gpio_set_value(gpiomtd->plat.gpio_ale, !!(ctrl & NAND_ALE)); |
| gpio_nand_dosync(gpiomtd); |
| } |
| if (cmd == NAND_CMD_NONE) |
| return; |
| |
| writeb(cmd, gpiomtd->nand_chip.IO_ADDR_W); |
| gpio_nand_dosync(gpiomtd); |
| } |
| |
| static void gpio_nand_writebuf(struct mtd_info *mtd, const u_char *buf, int len) |
| { |
| struct nand_chip *this = mtd->priv; |
| |
| writesb(this->IO_ADDR_W, buf, len); |
| } |
| |
| static void gpio_nand_readbuf(struct mtd_info *mtd, u_char *buf, int len) |
| { |
| struct nand_chip *this = mtd->priv; |
| |
| readsb(this->IO_ADDR_R, buf, len); |
| } |
| |
| static void gpio_nand_writebuf16(struct mtd_info *mtd, const u_char *buf, |
| int len) |
| { |
| struct nand_chip *this = mtd->priv; |
| |
| if (IS_ALIGNED((unsigned long)buf, 2)) { |
| writesw(this->IO_ADDR_W, buf, len>>1); |
| } else { |
| int i; |
| unsigned short *ptr = (unsigned short *)buf; |
| |
| for (i = 0; i < len; i += 2, ptr++) |
| writew(*ptr, this->IO_ADDR_W); |
| } |
| } |
| |
| static void gpio_nand_readbuf16(struct mtd_info *mtd, u_char *buf, int len) |
| { |
| struct nand_chip *this = mtd->priv; |
| |
| if (IS_ALIGNED((unsigned long)buf, 2)) { |
| readsw(this->IO_ADDR_R, buf, len>>1); |
| } else { |
| int i; |
| unsigned short *ptr = (unsigned short *)buf; |
| |
| for (i = 0; i < len; i += 2, ptr++) |
| *ptr = readw(this->IO_ADDR_R); |
| } |
| } |
| |
| static int gpio_nand_devready(struct mtd_info *mtd) |
| { |
| struct gpiomtd *gpiomtd = gpio_nand_getpriv(mtd); |
| return gpio_get_value(gpiomtd->plat.gpio_rdy); |
| } |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id gpio_nand_id_table[] = { |
| { .compatible = "gpio-control-nand" }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, gpio_nand_id_table); |
| |
| static int gpio_nand_get_config_of(const struct device *dev, |
| struct gpio_nand_platdata *plat) |
| { |
| u32 val; |
| |
| if (!of_property_read_u32(dev->of_node, "bank-width", &val)) { |
| if (val == 2) { |
| plat->options |= NAND_BUSWIDTH_16; |
| } else if (val != 1) { |
| dev_err(dev, "invalid bank-width %u\n", val); |
| return -EINVAL; |
| } |
| } |
| |
| plat->gpio_rdy = of_get_gpio(dev->of_node, 0); |
| plat->gpio_nce = of_get_gpio(dev->of_node, 1); |
| plat->gpio_ale = of_get_gpio(dev->of_node, 2); |
| plat->gpio_cle = of_get_gpio(dev->of_node, 3); |
| plat->gpio_nwp = of_get_gpio(dev->of_node, 4); |
| |
| if (!of_property_read_u32(dev->of_node, "chip-delay", &val)) |
| plat->chip_delay = val; |
| |
| return 0; |
| } |
| |
| static struct resource *gpio_nand_get_io_sync_of(struct platform_device *pdev) |
| { |
| struct resource *r = devm_kzalloc(&pdev->dev, sizeof(*r), GFP_KERNEL); |
| u64 addr; |
| |
| if (!r || of_property_read_u64(pdev->dev.of_node, |
| "gpio-control-nand,io-sync-reg", &addr)) |
| return NULL; |
| |
| r->start = addr; |
| r->end = r->start + 0x3; |
| r->flags = IORESOURCE_MEM; |
| |
| return r; |
| } |
| #else /* CONFIG_OF */ |
| #define gpio_nand_id_table NULL |
| static inline int gpio_nand_get_config_of(const struct device *dev, |
| struct gpio_nand_platdata *plat) |
| { |
| return -ENOSYS; |
| } |
| |
| static inline struct resource * |
| gpio_nand_get_io_sync_of(struct platform_device *pdev) |
| { |
| return NULL; |
| } |
| #endif /* CONFIG_OF */ |
| |
| static inline int gpio_nand_get_config(const struct device *dev, |
| struct gpio_nand_platdata *plat) |
| { |
| int ret = gpio_nand_get_config_of(dev, plat); |
| |
| if (!ret) |
| return ret; |
| |
| if (dev->platform_data) { |
| memcpy(plat, dev->platform_data, sizeof(*plat)); |
| return 0; |
| } |
| |
| return -EINVAL; |
| } |
| |
| static inline struct resource * |
| gpio_nand_get_io_sync(struct platform_device *pdev) |
| { |
| struct resource *r = gpio_nand_get_io_sync_of(pdev); |
| |
| if (r) |
| return r; |
| |
| return platform_get_resource(pdev, IORESOURCE_MEM, 1); |
| } |
| |
| static int __devexit gpio_nand_remove(struct platform_device *dev) |
| { |
| struct gpiomtd *gpiomtd = platform_get_drvdata(dev); |
| struct resource *res; |
| |
| nand_release(&gpiomtd->mtd_info); |
| |
| res = gpio_nand_get_io_sync(dev); |
| iounmap(gpiomtd->io_sync); |
| if (res) |
| release_mem_region(res->start, resource_size(res)); |
| |
| res = platform_get_resource(dev, IORESOURCE_MEM, 0); |
| iounmap(gpiomtd->nand_chip.IO_ADDR_R); |
| release_mem_region(res->start, resource_size(res)); |
| |
| if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) |
| gpio_set_value(gpiomtd->plat.gpio_nwp, 0); |
| gpio_set_value(gpiomtd->plat.gpio_nce, 1); |
| |
| gpio_free(gpiomtd->plat.gpio_cle); |
| gpio_free(gpiomtd->plat.gpio_ale); |
| gpio_free(gpiomtd->plat.gpio_nce); |
| if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) |
| gpio_free(gpiomtd->plat.gpio_nwp); |
| gpio_free(gpiomtd->plat.gpio_rdy); |
| |
| kfree(gpiomtd); |
| |
| return 0; |
| } |
| |
| static void __iomem *request_and_remap(struct resource *res, size_t size, |
| const char *name, int *err) |
| { |
| void __iomem *ptr; |
| |
| if (!request_mem_region(res->start, resource_size(res), name)) { |
| *err = -EBUSY; |
| return NULL; |
| } |
| |
| ptr = ioremap(res->start, size); |
| if (!ptr) { |
| release_mem_region(res->start, resource_size(res)); |
| *err = -ENOMEM; |
| } |
| return ptr; |
| } |
| |
| static int __devinit gpio_nand_probe(struct platform_device *dev) |
| { |
| struct gpiomtd *gpiomtd; |
| struct nand_chip *this; |
| struct resource *res0, *res1; |
| struct mtd_part_parser_data ppdata = {}; |
| int ret = 0; |
| |
| if (!dev->dev.of_node && !dev->dev.platform_data) |
| return -EINVAL; |
| |
| res0 = platform_get_resource(dev, IORESOURCE_MEM, 0); |
| if (!res0) |
| return -EINVAL; |
| |
| gpiomtd = kzalloc(sizeof(*gpiomtd), GFP_KERNEL); |
| if (gpiomtd == NULL) { |
| dev_err(&dev->dev, "failed to create NAND MTD\n"); |
| return -ENOMEM; |
| } |
| |
| this = &gpiomtd->nand_chip; |
| this->IO_ADDR_R = request_and_remap(res0, 2, "NAND", &ret); |
| if (!this->IO_ADDR_R) { |
| dev_err(&dev->dev, "unable to map NAND\n"); |
| goto err_map; |
| } |
| |
| res1 = gpio_nand_get_io_sync(dev); |
| if (res1) { |
| gpiomtd->io_sync = request_and_remap(res1, 4, "NAND sync", &ret); |
| if (!gpiomtd->io_sync) { |
| dev_err(&dev->dev, "unable to map sync NAND\n"); |
| goto err_sync; |
| } |
| } |
| |
| ret = gpio_nand_get_config(&dev->dev, &gpiomtd->plat); |
| if (ret) |
| goto err_nce; |
| |
| ret = gpio_request(gpiomtd->plat.gpio_nce, "NAND NCE"); |
| if (ret) |
| goto err_nce; |
| gpio_direction_output(gpiomtd->plat.gpio_nce, 1); |
| if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) { |
| ret = gpio_request(gpiomtd->plat.gpio_nwp, "NAND NWP"); |
| if (ret) |
| goto err_nwp; |
| gpio_direction_output(gpiomtd->plat.gpio_nwp, 1); |
| } |
| ret = gpio_request(gpiomtd->plat.gpio_ale, "NAND ALE"); |
| if (ret) |
| goto err_ale; |
| gpio_direction_output(gpiomtd->plat.gpio_ale, 0); |
| ret = gpio_request(gpiomtd->plat.gpio_cle, "NAND CLE"); |
| if (ret) |
| goto err_cle; |
| gpio_direction_output(gpiomtd->plat.gpio_cle, 0); |
| ret = gpio_request(gpiomtd->plat.gpio_rdy, "NAND RDY"); |
| if (ret) |
| goto err_rdy; |
| gpio_direction_input(gpiomtd->plat.gpio_rdy); |
| |
| |
| this->IO_ADDR_W = this->IO_ADDR_R; |
| this->ecc.mode = NAND_ECC_SOFT; |
| this->options = gpiomtd->plat.options; |
| this->chip_delay = gpiomtd->plat.chip_delay; |
| |
| /* install our routines */ |
| this->cmd_ctrl = gpio_nand_cmd_ctrl; |
| this->dev_ready = gpio_nand_devready; |
| |
| if (this->options & NAND_BUSWIDTH_16) { |
| this->read_buf = gpio_nand_readbuf16; |
| this->write_buf = gpio_nand_writebuf16; |
| } else { |
| this->read_buf = gpio_nand_readbuf; |
| this->write_buf = gpio_nand_writebuf; |
| } |
| |
| /* set the mtd private data for the nand driver */ |
| gpiomtd->mtd_info.priv = this; |
| gpiomtd->mtd_info.owner = THIS_MODULE; |
| |
| if (nand_scan(&gpiomtd->mtd_info, 1)) { |
| dev_err(&dev->dev, "no nand chips found?\n"); |
| ret = -ENXIO; |
| goto err_wp; |
| } |
| |
| if (gpiomtd->plat.adjust_parts) |
| gpiomtd->plat.adjust_parts(&gpiomtd->plat, |
| gpiomtd->mtd_info.size); |
| |
| ppdata.of_node = dev->dev.of_node; |
| ret = mtd_device_parse_register(&gpiomtd->mtd_info, NULL, &ppdata, |
| gpiomtd->plat.parts, |
| gpiomtd->plat.num_parts); |
| if (ret) |
| goto err_wp; |
| platform_set_drvdata(dev, gpiomtd); |
| |
| return 0; |
| |
| err_wp: |
| if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) |
| gpio_set_value(gpiomtd->plat.gpio_nwp, 0); |
| gpio_free(gpiomtd->plat.gpio_rdy); |
| err_rdy: |
| gpio_free(gpiomtd->plat.gpio_cle); |
| err_cle: |
| gpio_free(gpiomtd->plat.gpio_ale); |
| err_ale: |
| if (gpio_is_valid(gpiomtd->plat.gpio_nwp)) |
| gpio_free(gpiomtd->plat.gpio_nwp); |
| err_nwp: |
| gpio_free(gpiomtd->plat.gpio_nce); |
| err_nce: |
| iounmap(gpiomtd->io_sync); |
| if (res1) |
| release_mem_region(res1->start, resource_size(res1)); |
| err_sync: |
| iounmap(gpiomtd->nand_chip.IO_ADDR_R); |
| release_mem_region(res0->start, resource_size(res0)); |
| err_map: |
| kfree(gpiomtd); |
| return ret; |
| } |
| |
| static struct platform_driver gpio_nand_driver = { |
| .probe = gpio_nand_probe, |
| .remove = gpio_nand_remove, |
| .driver = { |
| .name = "gpio-nand", |
| .of_match_table = gpio_nand_id_table, |
| }, |
| }; |
| |
| module_platform_driver(gpio_nand_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>"); |
| MODULE_DESCRIPTION("GPIO NAND Driver"); |