| /* |
| * at91sam9n12.dtsi - Device Tree include file for AT91SAM9N12 SoC |
| * |
| * Copyright (C) 2012 Atmel, |
| * 2012 Hong Xu <hong.xu@atmel.com> |
| * |
| * Licensed under GPLv2 or later. |
| */ |
| |
| /include/ "skeleton.dtsi" |
| |
| / { |
| model = "Atmel AT91SAM9N12 SoC"; |
| compatible = "atmel,at91sam9n12"; |
| interrupt-parent = <&aic>; |
| |
| aliases { |
| serial0 = &dbgu; |
| serial1 = &usart0; |
| serial2 = &usart1; |
| serial3 = &usart2; |
| serial4 = &usart3; |
| gpio0 = &pioA; |
| gpio1 = &pioB; |
| gpio2 = &pioC; |
| gpio3 = &pioD; |
| tcb0 = &tcb0; |
| tcb1 = &tcb1; |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| ssc0 = &ssc0; |
| }; |
| cpus { |
| cpu@0 { |
| compatible = "arm,arm926ejs"; |
| }; |
| }; |
| |
| memory { |
| reg = <0x20000000 0x10000000>; |
| }; |
| |
| ahb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| apb { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| aic: interrupt-controller@fffff000 { |
| #interrupt-cells = <3>; |
| compatible = "atmel,at91rm9200-aic"; |
| interrupt-controller; |
| reg = <0xfffff000 0x200>; |
| }; |
| |
| ramc0: ramc@ffffe800 { |
| compatible = "atmel,at91sam9g45-ddramc"; |
| reg = <0xffffe800 0x200>; |
| }; |
| |
| pmc: pmc@fffffc00 { |
| compatible = "atmel,at91rm9200-pmc"; |
| reg = <0xfffffc00 0x100>; |
| }; |
| |
| rstc@fffffe00 { |
| compatible = "atmel,at91sam9g45-rstc"; |
| reg = <0xfffffe00 0x10>; |
| }; |
| |
| pit: timer@fffffe30 { |
| compatible = "atmel,at91sam9260-pit"; |
| reg = <0xfffffe30 0xf>; |
| interrupts = <1 4 7>; |
| }; |
| |
| shdwc@fffffe10 { |
| compatible = "atmel,at91sam9x5-shdwc"; |
| reg = <0xfffffe10 0x10>; |
| }; |
| |
| mmc0: mmc@f0008000 { |
| compatible = "atmel,hsmci"; |
| reg = <0xf0008000 0x600>; |
| interrupts = <12 4 0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| tcb0: timer@f8008000 { |
| compatible = "atmel,at91sam9x5-tcb"; |
| reg = <0xf8008000 0x100>; |
| interrupts = <17 4 0>; |
| }; |
| |
| tcb1: timer@f800c000 { |
| compatible = "atmel,at91sam9x5-tcb"; |
| reg = <0xf800c000 0x100>; |
| interrupts = <17 4 0>; |
| }; |
| |
| dma: dma-controller@ffffec00 { |
| compatible = "atmel,at91sam9g45-dma"; |
| reg = <0xffffec00 0x200>; |
| interrupts = <20 4 0>; |
| }; |
| |
| pinctrl@fffff400 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus"; |
| ranges = <0xfffff400 0xfffff400 0x800>; |
| |
| atmel,mux-mask = < |
| /* A B C */ |
| 0xffffffff 0xffe07983 0x00000000 /* pioA */ |
| 0x00040000 0x00047e0f 0x00000000 /* pioB */ |
| 0xfdffffff 0x07c00000 0xb83fffff /* pioC */ |
| 0x003fffff 0x003f8000 0x00000000 /* pioD */ |
| >; |
| |
| /* shared pinctrl settings */ |
| dbgu { |
| pinctrl_dbgu: dbgu-0 { |
| atmel,pins = |
| <0 9 0x1 0x0 /* PA9 periph A */ |
| 0 10 0x1 0x1>; /* PA10 periph with pullup */ |
| }; |
| }; |
| |
| usart0 { |
| pinctrl_usart0: usart0-0 { |
| atmel,pins = |
| <0 1 0x1 0x1 /* PA1 periph A with pullup */ |
| 0 0 0x1 0x0>; /* PA0 periph A */ |
| }; |
| |
| pinctrl_usart0_rts: usart0_rts-0 { |
| atmel,pins = |
| <0 2 0x1 0x0>; /* PA2 periph A */ |
| }; |
| |
| pinctrl_usart0_cts: usart0_cts-0 { |
| atmel,pins = |
| <0 3 0x1 0x0>; /* PA3 periph A */ |
| }; |
| }; |
| |
| usart1 { |
| pinctrl_usart1: usart1-0 { |
| atmel,pins = |
| <0 6 0x1 0x1 /* PA6 periph A with pullup */ |
| 0 5 0x1 0x0>; /* PA5 periph A */ |
| }; |
| }; |
| |
| usart2 { |
| pinctrl_usart2: usart2-0 { |
| atmel,pins = |
| <0 8 0x1 0x1 /* PA8 periph A with pullup */ |
| 0 7 0x1 0x0>; /* PA7 periph A */ |
| }; |
| |
| pinctrl_usart2_rts: usart2_rts-0 { |
| atmel,pins = |
| <1 0 0x2 0x0>; /* PB0 periph B */ |
| }; |
| |
| pinctrl_usart2_cts: usart2_cts-0 { |
| atmel,pins = |
| <1 1 0x2 0x0>; /* PB1 periph B */ |
| }; |
| }; |
| |
| usart3 { |
| pinctrl_usart3: usart3-0 { |
| atmel,pins = |
| <2 23 0x2 0x1 /* PC23 periph B with pullup */ |
| 2 22 0x2 0x0>; /* PC22 periph B */ |
| }; |
| |
| pinctrl_usart3_rts: usart3_rts-0 { |
| atmel,pins = |
| <2 24 0x2 0x0>; /* PC24 periph B */ |
| }; |
| |
| pinctrl_usart3_cts: usart3_cts-0 { |
| atmel,pins = |
| <2 25 0x2 0x0>; /* PC25 periph B */ |
| }; |
| }; |
| |
| uart0 { |
| pinctrl_uart0: uart0-0 { |
| atmel,pins = |
| <2 9 0x3 0x1 /* PC9 periph C with pullup */ |
| 2 8 0x3 0x0>; /* PC8 periph C */ |
| }; |
| }; |
| |
| uart1 { |
| pinctrl_uart1: uart1-0 { |
| atmel,pins = |
| <2 16 0x3 0x1 /* PC17 periph C with pullup */ |
| 2 17 0x3 0x0>; /* PC16 periph C */ |
| }; |
| }; |
| |
| nand { |
| pinctrl_nand: nand-0 { |
| atmel,pins = |
| <3 5 0x0 0x1 /* PD5 gpio RDY pin pull_up*/ |
| 3 4 0x0 0x1>; /* PD4 gpio enable pin pull_up */ |
| }; |
| }; |
| |
| mmc0 { |
| pinctrl_mmc0_slot0_clk_cmd_dat0: mmc0_slot0_clk_cmd_dat0-0 { |
| atmel,pins = |
| <0 17 0x1 0x0 /* PA17 periph A */ |
| 0 16 0x1 0x1 /* PA16 periph A with pullup */ |
| 0 15 0x1 0x1>; /* PA15 periph A with pullup */ |
| }; |
| |
| pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 { |
| atmel,pins = |
| <0 18 0x1 0x1 /* PA18 periph A with pullup */ |
| 0 19 0x1 0x1 /* PA19 periph A with pullup */ |
| 0 20 0x1 0x1>; /* PA20 periph A with pullup */ |
| }; |
| |
| pinctrl_mmc0_slot0_dat4_7: mmc0_slot0_dat4_7-0 { |
| atmel,pins = |
| <0 11 0x2 0x1 /* PA11 periph B with pullup */ |
| 0 12 0x2 0x1 /* PA12 periph B with pullup */ |
| 0 13 0x2 0x1 /* PA13 periph B with pullup */ |
| 0 14 0x2 0x1>; /* PA14 periph B with pullup */ |
| }; |
| }; |
| |
| ssc0 { |
| pinctrl_ssc0_tx: ssc0_tx-0 { |
| atmel,pins = |
| <0 24 0x2 0x0 /* PA24 periph B */ |
| 0 25 0x2 0x0 /* PA25 periph B */ |
| 0 26 0x2 0x0>; /* PA26 periph B */ |
| }; |
| |
| pinctrl_ssc0_rx: ssc0_rx-0 { |
| atmel,pins = |
| <0 27 0x2 0x0 /* PA27 periph B */ |
| 0 28 0x2 0x0 /* PA28 periph B */ |
| 0 29 0x2 0x0>; /* PA29 periph B */ |
| }; |
| }; |
| |
| pioA: gpio@fffff400 { |
| compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| reg = <0xfffff400 0x200>; |
| interrupts = <2 4 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pioB: gpio@fffff600 { |
| compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| reg = <0xfffff600 0x200>; |
| interrupts = <2 4 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pioC: gpio@fffff800 { |
| compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| reg = <0xfffff800 0x200>; |
| interrupts = <3 4 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pioD: gpio@fffffa00 { |
| compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; |
| reg = <0xfffffa00 0x200>; |
| interrupts = <3 4 1>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| dbgu: serial@fffff200 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xfffff200 0x200>; |
| interrupts = <1 4 7>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_dbgu>; |
| status = "disabled"; |
| }; |
| |
| ssc0: ssc@f0010000 { |
| compatible = "atmel,at91sam9g45-ssc"; |
| reg = <0xf0010000 0x4000>; |
| interrupts = <28 4 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; |
| status = "disabled"; |
| }; |
| |
| usart0: serial@f801c000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xf801c000 0x4000>; |
| interrupts = <5 4 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart0>; |
| status = "disabled"; |
| }; |
| |
| usart1: serial@f8020000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xf8020000 0x4000>; |
| interrupts = <6 4 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart1>; |
| status = "disabled"; |
| }; |
| |
| usart2: serial@f8024000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xf8024000 0x4000>; |
| interrupts = <7 4 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart2>; |
| status = "disabled"; |
| }; |
| |
| usart3: serial@f8028000 { |
| compatible = "atmel,at91sam9260-usart"; |
| reg = <0xf8028000 0x4000>; |
| interrupts = <8 4 5>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usart3>; |
| status = "disabled"; |
| }; |
| |
| i2c0: i2c@f8010000 { |
| compatible = "atmel,at91sam9x5-i2c"; |
| reg = <0xf8010000 0x100>; |
| interrupts = <9 4 6>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@f8014000 { |
| compatible = "atmel,at91sam9x5-i2c"; |
| reg = <0xf8014000 0x100>; |
| interrupts = <10 4 6>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| nand0: nand@40000000 { |
| compatible = "atmel,at91rm9200-nand"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = < 0x40000000 0x10000000 |
| 0xffffe000 0x00000600 |
| 0xffffe600 0x00000200 |
| 0x00108000 0x00018000 |
| >; |
| atmel,pmecc-lookup-table-offset = <0x0 0x8000>; |
| atmel,nand-addr-offset = <21>; |
| atmel,nand-cmd-offset = <22>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_nand>; |
| gpios = <&pioD 5 0 |
| &pioD 4 0 |
| 0 |
| >; |
| status = "disabled"; |
| }; |
| |
| usb0: ohci@00500000 { |
| compatible = "atmel,at91rm9200-ohci", "usb-ohci"; |
| reg = <0x00500000 0x00100000>; |
| interrupts = <22 4 2>; |
| status = "disabled"; |
| }; |
| }; |
| |
| i2c@0 { |
| compatible = "i2c-gpio"; |
| gpios = <&pioA 30 0 /* sda */ |
| &pioA 31 0 /* scl */ |
| >; |
| i2c-gpio,sda-open-drain; |
| i2c-gpio,scl-open-drain; |
| i2c-gpio,delay-us = <2>; /* ~100 kHz */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |