| /* |
| * This file is part of wl1271 |
| * |
| * Copyright (C) 2008-2010 Nokia Corporation |
| * |
| * Contact: Luciano Coelho <luciano.coelho@nokia.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License |
| * version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA |
| * 02110-1301 USA |
| * |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/firmware.h> |
| #include <linux/delay.h> |
| #include <linux/spi/spi.h> |
| #include <linux/crc32.h> |
| #include <linux/etherdevice.h> |
| #include <linux/vmalloc.h> |
| #include <linux/platform_device.h> |
| #include <linux/slab.h> |
| |
| #include "wl12xx.h" |
| #include "wl12xx_80211.h" |
| #include "reg.h" |
| #include "io.h" |
| #include "event.h" |
| #include "tx.h" |
| #include "rx.h" |
| #include "ps.h" |
| #include "init.h" |
| #include "debugfs.h" |
| #include "cmd.h" |
| #include "boot.h" |
| #include "testmode.h" |
| #include "scan.h" |
| |
| #define WL1271_BOOT_RETRIES 3 |
| |
| static struct conf_drv_settings default_conf = { |
| .sg = { |
| .params = { |
| [CONF_SG_BT_PER_THRESHOLD] = 7500, |
| [CONF_SG_HV3_MAX_OVERRIDE] = 0, |
| [CONF_SG_BT_NFS_SAMPLE_INTERVAL] = 400, |
| [CONF_SG_BT_LOAD_RATIO] = 50, |
| [CONF_SG_AUTO_PS_MODE] = 1, |
| [CONF_SG_AUTO_SCAN_PROBE_REQ] = 170, |
| [CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3] = 50, |
| [CONF_SG_ANTENNA_CONFIGURATION] = 0, |
| [CONF_SG_BEACON_MISS_PERCENT] = 60, |
| [CONF_SG_RATE_ADAPT_THRESH] = 12, |
| [CONF_SG_RATE_ADAPT_SNR] = 0, |
| [CONF_SG_WLAN_PS_BT_ACL_MASTER_MIN_BR] = 10, |
| [CONF_SG_WLAN_PS_BT_ACL_MASTER_MAX_BR] = 30, |
| [CONF_SG_WLAN_PS_MAX_BT_ACL_MASTER_BR] = 8, |
| [CONF_SG_WLAN_PS_BT_ACL_SLAVE_MIN_BR] = 20, |
| [CONF_SG_WLAN_PS_BT_ACL_SLAVE_MAX_BR] = 50, |
| /* Note: with UPSD, this should be 4 */ |
| [CONF_SG_WLAN_PS_MAX_BT_ACL_SLAVE_BR] = 8, |
| [CONF_SG_WLAN_PS_BT_ACL_MASTER_MIN_EDR] = 7, |
| [CONF_SG_WLAN_PS_BT_ACL_MASTER_MAX_EDR] = 25, |
| [CONF_SG_WLAN_PS_MAX_BT_ACL_MASTER_EDR] = 20, |
| /* Note: with UPDS, this should be 15 */ |
| [CONF_SG_WLAN_PS_BT_ACL_SLAVE_MIN_EDR] = 8, |
| /* Note: with UPDS, this should be 50 */ |
| [CONF_SG_WLAN_PS_BT_ACL_SLAVE_MAX_EDR] = 40, |
| /* Note: with UPDS, this should be 10 */ |
| [CONF_SG_WLAN_PS_MAX_BT_ACL_SLAVE_EDR] = 20, |
| [CONF_SG_RXT] = 1200, |
| [CONF_SG_TXT] = 1000, |
| [CONF_SG_ADAPTIVE_RXT_TXT] = 1, |
| [CONF_SG_PS_POLL_TIMEOUT] = 10, |
| [CONF_SG_UPSD_TIMEOUT] = 10, |
| [CONF_SG_WLAN_ACTIVE_BT_ACL_MASTER_MIN_EDR] = 7, |
| [CONF_SG_WLAN_ACTIVE_BT_ACL_MASTER_MAX_EDR] = 15, |
| [CONF_SG_WLAN_ACTIVE_MAX_BT_ACL_MASTER_EDR] = 15, |
| [CONF_SG_WLAN_ACTIVE_BT_ACL_SLAVE_MIN_EDR] = 8, |
| [CONF_SG_WLAN_ACTIVE_BT_ACL_SLAVE_MAX_EDR] = 20, |
| [CONF_SG_WLAN_ACTIVE_MAX_BT_ACL_SLAVE_EDR] = 15, |
| [CONF_SG_WLAN_ACTIVE_BT_ACL_MIN_BR] = 20, |
| [CONF_SG_WLAN_ACTIVE_BT_ACL_MAX_BR] = 50, |
| [CONF_SG_WLAN_ACTIVE_MAX_BT_ACL_BR] = 10, |
| [CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3] = 200, |
| [CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP] = 800, |
| [CONF_SG_PASSIVE_SCAN_A2DP_BT_TIME] = 75, |
| [CONF_SG_PASSIVE_SCAN_A2DP_WLAN_TIME] = 15, |
| [CONF_SG_HV3_MAX_SERVED] = 6, |
| [CONF_SG_DHCP_TIME] = 5000, |
| [CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP] = 100, |
| }, |
| .state = CONF_SG_PROTECTIVE, |
| }, |
| .rx = { |
| .rx_msdu_life_time = 512000, |
| .packet_detection_threshold = 0, |
| .ps_poll_timeout = 15, |
| .upsd_timeout = 15, |
| .rts_threshold = 2347, |
| .rx_cca_threshold = 0, |
| .irq_blk_threshold = 0xFFFF, |
| .irq_pkt_threshold = 0, |
| .irq_timeout = 600, |
| .queue_type = CONF_RX_QUEUE_TYPE_LOW_PRIORITY, |
| }, |
| .tx = { |
| .tx_energy_detection = 0, |
| .sta_rc_conf = { |
| .enabled_rates = 0, |
| .short_retry_limit = 10, |
| .long_retry_limit = 10, |
| .aflags = 0, |
| }, |
| .ac_conf_count = 4, |
| .ac_conf = { |
| [CONF_TX_AC_BE] = { |
| .ac = CONF_TX_AC_BE, |
| .cw_min = 15, |
| .cw_max = 63, |
| .aifsn = 3, |
| .tx_op_limit = 0, |
| }, |
| [CONF_TX_AC_BK] = { |
| .ac = CONF_TX_AC_BK, |
| .cw_min = 15, |
| .cw_max = 63, |
| .aifsn = 7, |
| .tx_op_limit = 0, |
| }, |
| [CONF_TX_AC_VI] = { |
| .ac = CONF_TX_AC_VI, |
| .cw_min = 15, |
| .cw_max = 63, |
| .aifsn = CONF_TX_AIFS_PIFS, |
| .tx_op_limit = 3008, |
| }, |
| [CONF_TX_AC_VO] = { |
| .ac = CONF_TX_AC_VO, |
| .cw_min = 15, |
| .cw_max = 63, |
| .aifsn = CONF_TX_AIFS_PIFS, |
| .tx_op_limit = 1504, |
| }, |
| }, |
| .ap_rc_conf = { |
| [0] = { |
| .enabled_rates = CONF_TX_AP_ENABLED_RATES, |
| .short_retry_limit = 10, |
| .long_retry_limit = 10, |
| .aflags = 0, |
| }, |
| [1] = { |
| .enabled_rates = CONF_TX_AP_ENABLED_RATES, |
| .short_retry_limit = 10, |
| .long_retry_limit = 10, |
| .aflags = 0, |
| }, |
| [2] = { |
| .enabled_rates = CONF_TX_AP_ENABLED_RATES, |
| .short_retry_limit = 10, |
| .long_retry_limit = 10, |
| .aflags = 0, |
| }, |
| [3] = { |
| .enabled_rates = CONF_TX_AP_ENABLED_RATES, |
| .short_retry_limit = 10, |
| .long_retry_limit = 10, |
| .aflags = 0, |
| }, |
| }, |
| .ap_mgmt_conf = { |
| .enabled_rates = CONF_TX_AP_DEFAULT_MGMT_RATES, |
| .short_retry_limit = 10, |
| .long_retry_limit = 10, |
| .aflags = 0, |
| }, |
| .ap_bcst_conf = { |
| .enabled_rates = CONF_HW_BIT_RATE_1MBPS, |
| .short_retry_limit = 10, |
| .long_retry_limit = 10, |
| .aflags = 0, |
| }, |
| .ap_max_tx_retries = 100, |
| .tid_conf_count = 4, |
| .tid_conf = { |
| [CONF_TX_AC_BE] = { |
| .queue_id = CONF_TX_AC_BE, |
| .channel_type = CONF_CHANNEL_TYPE_EDCF, |
| .tsid = CONF_TX_AC_BE, |
| .ps_scheme = CONF_PS_SCHEME_LEGACY, |
| .ack_policy = CONF_ACK_POLICY_LEGACY, |
| .apsd_conf = {0, 0}, |
| }, |
| [CONF_TX_AC_BK] = { |
| .queue_id = CONF_TX_AC_BK, |
| .channel_type = CONF_CHANNEL_TYPE_EDCF, |
| .tsid = CONF_TX_AC_BK, |
| .ps_scheme = CONF_PS_SCHEME_LEGACY, |
| .ack_policy = CONF_ACK_POLICY_LEGACY, |
| .apsd_conf = {0, 0}, |
| }, |
| [CONF_TX_AC_VI] = { |
| .queue_id = CONF_TX_AC_VI, |
| .channel_type = CONF_CHANNEL_TYPE_EDCF, |
| .tsid = CONF_TX_AC_VI, |
| .ps_scheme = CONF_PS_SCHEME_LEGACY, |
| .ack_policy = CONF_ACK_POLICY_LEGACY, |
| .apsd_conf = {0, 0}, |
| }, |
| [CONF_TX_AC_VO] = { |
| .queue_id = CONF_TX_AC_VO, |
| .channel_type = CONF_CHANNEL_TYPE_EDCF, |
| .tsid = CONF_TX_AC_VO, |
| .ps_scheme = CONF_PS_SCHEME_LEGACY, |
| .ack_policy = CONF_ACK_POLICY_LEGACY, |
| .apsd_conf = {0, 0}, |
| }, |
| }, |
| .frag_threshold = IEEE80211_MAX_FRAG_THRESHOLD, |
| .tx_compl_timeout = 700, |
| .tx_compl_threshold = 4, |
| .basic_rate = CONF_HW_BIT_RATE_1MBPS, |
| .basic_rate_5 = CONF_HW_BIT_RATE_6MBPS, |
| .tmpl_short_retry_limit = 10, |
| .tmpl_long_retry_limit = 10, |
| }, |
| .conn = { |
| .wake_up_event = CONF_WAKE_UP_EVENT_DTIM, |
| .listen_interval = 1, |
| .bcn_filt_mode = CONF_BCN_FILT_MODE_ENABLED, |
| .bcn_filt_ie_count = 1, |
| .bcn_filt_ie = { |
| [0] = { |
| .ie = WLAN_EID_CHANNEL_SWITCH, |
| .rule = CONF_BCN_RULE_PASS_ON_APPEARANCE, |
| } |
| }, |
| .synch_fail_thold = 10, |
| .bss_lose_timeout = 100, |
| .beacon_rx_timeout = 10000, |
| .broadcast_timeout = 20000, |
| .rx_broadcast_in_ps = 1, |
| .ps_poll_threshold = 10, |
| .ps_poll_recovery_period = 700, |
| .bet_enable = CONF_BET_MODE_ENABLE, |
| .bet_max_consecutive = 10, |
| .psm_entry_retries = 5, |
| .psm_entry_nullfunc_retries = 3, |
| .psm_entry_hangover_period = 1, |
| .keep_alive_interval = 55000, |
| .max_listen_interval = 20, |
| }, |
| .itrim = { |
| .enable = false, |
| .timeout = 50000, |
| }, |
| .pm_config = { |
| .host_clk_settling_time = 5000, |
| .host_fast_wakeup_support = false |
| }, |
| .roam_trigger = { |
| .trigger_pacing = 1, |
| .avg_weight_rssi_beacon = 20, |
| .avg_weight_rssi_data = 10, |
| .avg_weight_snr_beacon = 20, |
| .avg_weight_snr_data = 10, |
| }, |
| .scan = { |
| .min_dwell_time_active = 7500, |
| .max_dwell_time_active = 30000, |
| .min_dwell_time_passive = 30000, |
| .max_dwell_time_passive = 60000, |
| .num_probe_reqs = 2, |
| }, |
| .rf = { |
| .tx_per_channel_power_compensation_2 = { |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| }, |
| .tx_per_channel_power_compensation_5 = { |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
| }, |
| }, |
| .ht = { |
| .tx_ba_win_size = 64, |
| .inactivity_timeout = 10000, |
| }, |
| }; |
| |
| static void __wl1271_op_remove_interface(struct wl1271 *wl); |
| static void wl1271_free_ap_keys(struct wl1271 *wl); |
| |
| |
| static void wl1271_device_release(struct device *dev) |
| { |
| |
| } |
| |
| static struct platform_device wl1271_device = { |
| .name = "wl1271", |
| .id = -1, |
| |
| /* device model insists to have a release function */ |
| .dev = { |
| .release = wl1271_device_release, |
| }, |
| }; |
| |
| static LIST_HEAD(wl_list); |
| |
| static int wl1271_dev_notify(struct notifier_block *me, unsigned long what, |
| void *arg) |
| { |
| struct net_device *dev = arg; |
| struct wireless_dev *wdev; |
| struct wiphy *wiphy; |
| struct ieee80211_hw *hw; |
| struct wl1271 *wl; |
| struct wl1271 *wl_temp; |
| int ret = 0; |
| |
| /* Check that this notification is for us. */ |
| if (what != NETDEV_CHANGE) |
| return NOTIFY_DONE; |
| |
| wdev = dev->ieee80211_ptr; |
| if (wdev == NULL) |
| return NOTIFY_DONE; |
| |
| wiphy = wdev->wiphy; |
| if (wiphy == NULL) |
| return NOTIFY_DONE; |
| |
| hw = wiphy_priv(wiphy); |
| if (hw == NULL) |
| return NOTIFY_DONE; |
| |
| wl_temp = hw->priv; |
| list_for_each_entry(wl, &wl_list, list) { |
| if (wl == wl_temp) |
| break; |
| } |
| if (wl != wl_temp) |
| return NOTIFY_DONE; |
| |
| mutex_lock(&wl->mutex); |
| |
| if (wl->state == WL1271_STATE_OFF) |
| goto out; |
| |
| if (!test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags)) |
| goto out; |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| if ((dev->operstate == IF_OPER_UP) && |
| !test_and_set_bit(WL1271_FLAG_STA_STATE_SENT, &wl->flags)) { |
| wl1271_cmd_set_sta_state(wl); |
| wl1271_info("Association completed."); |
| } |
| |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| |
| return NOTIFY_OK; |
| } |
| |
| static int wl1271_reg_notify(struct wiphy *wiphy, |
| struct regulatory_request *request) |
| { |
| struct ieee80211_supported_band *band; |
| struct ieee80211_channel *ch; |
| int i; |
| |
| band = wiphy->bands[IEEE80211_BAND_5GHZ]; |
| for (i = 0; i < band->n_channels; i++) { |
| ch = &band->channels[i]; |
| if (ch->flags & IEEE80211_CHAN_DISABLED) |
| continue; |
| |
| if (ch->flags & IEEE80211_CHAN_RADAR) |
| ch->flags |= IEEE80211_CHAN_NO_IBSS | |
| IEEE80211_CHAN_PASSIVE_SCAN; |
| |
| } |
| |
| return 0; |
| } |
| |
| static void wl1271_conf_init(struct wl1271 *wl) |
| { |
| |
| /* |
| * This function applies the default configuration to the driver. This |
| * function is invoked upon driver load (spi probe.) |
| * |
| * The configuration is stored in a run-time structure in order to |
| * facilitate for run-time adjustment of any of the parameters. Making |
| * changes to the configuration structure will apply the new values on |
| * the next interface up (wl1271_op_start.) |
| */ |
| |
| /* apply driver default configuration */ |
| memcpy(&wl->conf, &default_conf, sizeof(default_conf)); |
| } |
| |
| |
| static int wl1271_plt_init(struct wl1271 *wl) |
| { |
| struct conf_tx_ac_category *conf_ac; |
| struct conf_tx_tid *conf_tid; |
| int ret, i; |
| |
| ret = wl1271_cmd_general_parms(wl); |
| if (ret < 0) |
| return ret; |
| |
| ret = wl1271_cmd_radio_parms(wl); |
| if (ret < 0) |
| return ret; |
| |
| ret = wl1271_cmd_ext_radio_parms(wl); |
| if (ret < 0) |
| return ret; |
| |
| ret = wl1271_sta_init_templates_config(wl); |
| if (ret < 0) |
| return ret; |
| |
| ret = wl1271_acx_init_mem_config(wl); |
| if (ret < 0) |
| return ret; |
| |
| /* PHY layer config */ |
| ret = wl1271_init_phy_config(wl); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| ret = wl1271_acx_dco_itrim_params(wl); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| /* Initialize connection monitoring thresholds */ |
| ret = wl1271_acx_conn_monit_params(wl, false); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| /* Bluetooth WLAN coexistence */ |
| ret = wl1271_init_pta(wl); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| /* Energy detection */ |
| ret = wl1271_init_energy_detection(wl); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| /* Default fragmentation threshold */ |
| ret = wl1271_acx_frag_threshold(wl, wl->conf.tx.frag_threshold); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| /* Default TID/AC configuration */ |
| BUG_ON(wl->conf.tx.tid_conf_count != wl->conf.tx.ac_conf_count); |
| for (i = 0; i < wl->conf.tx.tid_conf_count; i++) { |
| conf_ac = &wl->conf.tx.ac_conf[i]; |
| ret = wl1271_acx_ac_cfg(wl, conf_ac->ac, conf_ac->cw_min, |
| conf_ac->cw_max, conf_ac->aifsn, |
| conf_ac->tx_op_limit); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| conf_tid = &wl->conf.tx.tid_conf[i]; |
| ret = wl1271_acx_tid_cfg(wl, conf_tid->queue_id, |
| conf_tid->channel_type, |
| conf_tid->tsid, |
| conf_tid->ps_scheme, |
| conf_tid->ack_policy, |
| conf_tid->apsd_conf[0], |
| conf_tid->apsd_conf[1]); |
| if (ret < 0) |
| goto out_free_memmap; |
| } |
| |
| /* Enable data path */ |
| ret = wl1271_cmd_data_path(wl, 1); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| /* Configure for CAM power saving (ie. always active) */ |
| ret = wl1271_acx_sleep_auth(wl, WL1271_PSM_CAM); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| /* configure PM */ |
| ret = wl1271_acx_pm_config(wl); |
| if (ret < 0) |
| goto out_free_memmap; |
| |
| return 0; |
| |
| out_free_memmap: |
| kfree(wl->target_mem_map); |
| wl->target_mem_map = NULL; |
| |
| return ret; |
| } |
| |
| static void wl1271_fw_status(struct wl1271 *wl, |
| struct wl1271_fw_status *status) |
| { |
| struct timespec ts; |
| u32 total = 0; |
| int i; |
| |
| wl1271_raw_read(wl, FW_STATUS_ADDR, status, sizeof(*status), false); |
| |
| wl1271_debug(DEBUG_IRQ, "intr: 0x%x (fw_rx_counter = %d, " |
| "drv_rx_counter = %d, tx_results_counter = %d)", |
| status->intr, |
| status->fw_rx_counter, |
| status->drv_rx_counter, |
| status->tx_results_counter); |
| |
| /* update number of available TX blocks */ |
| for (i = 0; i < NUM_TX_QUEUES; i++) { |
| u32 cnt = le32_to_cpu(status->tx_released_blks[i]) - |
| wl->tx_blocks_freed[i]; |
| |
| wl->tx_blocks_freed[i] = |
| le32_to_cpu(status->tx_released_blks[i]); |
| wl->tx_blocks_available += cnt; |
| total += cnt; |
| } |
| |
| /* if more blocks are available now, tx work can be scheduled */ |
| if (total) |
| clear_bit(WL1271_FLAG_FW_TX_BUSY, &wl->flags); |
| |
| /* update the host-chipset time offset */ |
| getnstimeofday(&ts); |
| wl->time_offset = (timespec_to_ns(&ts) >> 10) - |
| (s64)le32_to_cpu(status->fw_localtime); |
| } |
| |
| #define WL1271_IRQ_MAX_LOOPS 10 |
| |
| static void wl1271_irq_work(struct work_struct *work) |
| { |
| int ret; |
| u32 intr; |
| int loopcount = WL1271_IRQ_MAX_LOOPS; |
| unsigned long flags; |
| struct wl1271 *wl = |
| container_of(work, struct wl1271, irq_work); |
| |
| mutex_lock(&wl->mutex); |
| |
| wl1271_debug(DEBUG_IRQ, "IRQ work"); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) |
| goto out; |
| |
| ret = wl1271_ps_elp_wakeup(wl, true); |
| if (ret < 0) |
| goto out; |
| |
| spin_lock_irqsave(&wl->wl_lock, flags); |
| while (test_bit(WL1271_FLAG_IRQ_PENDING, &wl->flags) && loopcount) { |
| clear_bit(WL1271_FLAG_IRQ_PENDING, &wl->flags); |
| spin_unlock_irqrestore(&wl->wl_lock, flags); |
| loopcount--; |
| |
| wl1271_fw_status(wl, wl->fw_status); |
| intr = le32_to_cpu(wl->fw_status->intr); |
| if (!intr) { |
| wl1271_debug(DEBUG_IRQ, "Zero interrupt received."); |
| spin_lock_irqsave(&wl->wl_lock, flags); |
| continue; |
| } |
| |
| intr &= WL1271_INTR_MASK; |
| |
| if (unlikely(intr & WL1271_ACX_INTR_WATCHDOG)) { |
| wl1271_error("watchdog interrupt received! " |
| "starting recovery."); |
| ieee80211_queue_work(wl->hw, &wl->recovery_work); |
| |
| /* restarting the chip. ignore any other interrupt. */ |
| goto out; |
| } |
| |
| if (intr & WL1271_ACX_INTR_DATA) { |
| wl1271_debug(DEBUG_IRQ, "WL1271_ACX_INTR_DATA"); |
| |
| /* check for tx results */ |
| if (wl->fw_status->tx_results_counter != |
| (wl->tx_results_count & 0xff)) |
| wl1271_tx_complete(wl); |
| |
| /* Check if any tx blocks were freed */ |
| if (!test_bit(WL1271_FLAG_FW_TX_BUSY, &wl->flags) && |
| wl->tx_queue_count) { |
| /* |
| * In order to avoid starvation of the TX path, |
| * call the work function directly. |
| */ |
| wl1271_tx_work_locked(wl); |
| } |
| |
| wl1271_rx(wl, wl->fw_status); |
| } |
| |
| if (intr & WL1271_ACX_INTR_EVENT_A) { |
| wl1271_debug(DEBUG_IRQ, "WL1271_ACX_INTR_EVENT_A"); |
| wl1271_event_handle(wl, 0); |
| } |
| |
| if (intr & WL1271_ACX_INTR_EVENT_B) { |
| wl1271_debug(DEBUG_IRQ, "WL1271_ACX_INTR_EVENT_B"); |
| wl1271_event_handle(wl, 1); |
| } |
| |
| if (intr & WL1271_ACX_INTR_INIT_COMPLETE) |
| wl1271_debug(DEBUG_IRQ, |
| "WL1271_ACX_INTR_INIT_COMPLETE"); |
| |
| if (intr & WL1271_ACX_INTR_HW_AVAILABLE) |
| wl1271_debug(DEBUG_IRQ, "WL1271_ACX_INTR_HW_AVAILABLE"); |
| |
| spin_lock_irqsave(&wl->wl_lock, flags); |
| } |
| |
| if (test_bit(WL1271_FLAG_IRQ_PENDING, &wl->flags)) |
| ieee80211_queue_work(wl->hw, &wl->irq_work); |
| else |
| clear_bit(WL1271_FLAG_IRQ_RUNNING, &wl->flags); |
| spin_unlock_irqrestore(&wl->wl_lock, flags); |
| |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| } |
| |
| static int wl1271_fetch_firmware(struct wl1271 *wl) |
| { |
| const struct firmware *fw; |
| const char *fw_name; |
| int ret; |
| |
| switch (wl->bss_type) { |
| case BSS_TYPE_AP_BSS: |
| fw_name = WL1271_AP_FW_NAME; |
| break; |
| case BSS_TYPE_IBSS: |
| case BSS_TYPE_STA_BSS: |
| fw_name = WL1271_FW_NAME; |
| break; |
| default: |
| wl1271_error("no compatible firmware for bss_type %d", |
| wl->bss_type); |
| return -EINVAL; |
| } |
| |
| wl1271_debug(DEBUG_BOOT, "booting firmware %s", fw_name); |
| |
| ret = request_firmware(&fw, fw_name, wl1271_wl_to_dev(wl)); |
| |
| if (ret < 0) { |
| wl1271_error("could not get firmware: %d", ret); |
| return ret; |
| } |
| |
| if (fw->size % 4) { |
| wl1271_error("firmware size is not multiple of 32 bits: %zu", |
| fw->size); |
| ret = -EILSEQ; |
| goto out; |
| } |
| |
| vfree(wl->fw); |
| wl->fw_len = fw->size; |
| wl->fw = vmalloc(wl->fw_len); |
| |
| if (!wl->fw) { |
| wl1271_error("could not allocate memory for the firmware"); |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| memcpy(wl->fw, fw->data, wl->fw_len); |
| wl->fw_bss_type = wl->bss_type; |
| ret = 0; |
| |
| out: |
| release_firmware(fw); |
| |
| return ret; |
| } |
| |
| static int wl1271_fetch_nvs(struct wl1271 *wl) |
| { |
| const struct firmware *fw; |
| int ret; |
| |
| ret = request_firmware(&fw, WL1271_NVS_NAME, wl1271_wl_to_dev(wl)); |
| |
| if (ret < 0) { |
| wl1271_error("could not get nvs file: %d", ret); |
| return ret; |
| } |
| |
| wl->nvs = kmemdup(fw->data, sizeof(struct wl1271_nvs_file), GFP_KERNEL); |
| |
| if (!wl->nvs) { |
| wl1271_error("could not allocate memory for the nvs file"); |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| wl->nvs_len = fw->size; |
| |
| out: |
| release_firmware(fw); |
| |
| return ret; |
| } |
| |
| static void wl1271_recovery_work(struct work_struct *work) |
| { |
| struct wl1271 *wl = |
| container_of(work, struct wl1271, recovery_work); |
| |
| mutex_lock(&wl->mutex); |
| |
| if (wl->state != WL1271_STATE_ON) |
| goto out; |
| |
| wl1271_info("Hardware recovery in progress."); |
| |
| if (test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags)) |
| ieee80211_connection_loss(wl->vif); |
| |
| /* reboot the chipset */ |
| __wl1271_op_remove_interface(wl); |
| ieee80211_restart_hw(wl->hw); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| } |
| |
| static void wl1271_fw_wakeup(struct wl1271 *wl) |
| { |
| u32 elp_reg; |
| |
| elp_reg = ELPCTRL_WAKE_UP; |
| wl1271_raw_write32(wl, HW_ACCESS_ELP_CTRL_REG_ADDR, elp_reg); |
| } |
| |
| static int wl1271_setup(struct wl1271 *wl) |
| { |
| wl->fw_status = kmalloc(sizeof(*wl->fw_status), GFP_KERNEL); |
| if (!wl->fw_status) |
| return -ENOMEM; |
| |
| wl->tx_res_if = kmalloc(sizeof(*wl->tx_res_if), GFP_KERNEL); |
| if (!wl->tx_res_if) { |
| kfree(wl->fw_status); |
| return -ENOMEM; |
| } |
| |
| return 0; |
| } |
| |
| static int wl1271_chip_wakeup(struct wl1271 *wl) |
| { |
| struct wl1271_partition_set partition; |
| int ret = 0; |
| |
| msleep(WL1271_PRE_POWER_ON_SLEEP); |
| ret = wl1271_power_on(wl); |
| if (ret < 0) |
| goto out; |
| msleep(WL1271_POWER_ON_SLEEP); |
| wl1271_io_reset(wl); |
| wl1271_io_init(wl); |
| |
| /* We don't need a real memory partition here, because we only want |
| * to use the registers at this point. */ |
| memset(&partition, 0, sizeof(partition)); |
| partition.reg.start = REGISTERS_BASE; |
| partition.reg.size = REGISTERS_DOWN_SIZE; |
| wl1271_set_partition(wl, &partition); |
| |
| /* ELP module wake up */ |
| wl1271_fw_wakeup(wl); |
| |
| /* whal_FwCtrl_BootSm() */ |
| |
| /* 0. read chip id from CHIP_ID */ |
| wl->chip.id = wl1271_read32(wl, CHIP_ID_B); |
| |
| /* 1. check if chip id is valid */ |
| |
| switch (wl->chip.id) { |
| case CHIP_ID_1271_PG10: |
| wl1271_warning("chip id 0x%x (1271 PG10) support is obsolete", |
| wl->chip.id); |
| |
| ret = wl1271_setup(wl); |
| if (ret < 0) |
| goto out; |
| break; |
| case CHIP_ID_1271_PG20: |
| wl1271_debug(DEBUG_BOOT, "chip id 0x%x (1271 PG20)", |
| wl->chip.id); |
| |
| ret = wl1271_setup(wl); |
| if (ret < 0) |
| goto out; |
| break; |
| default: |
| wl1271_warning("unsupported chip id: 0x%x", wl->chip.id); |
| ret = -ENODEV; |
| goto out; |
| } |
| |
| /* Make sure the firmware type matches the BSS type */ |
| if (wl->fw == NULL || wl->fw_bss_type != wl->bss_type) { |
| ret = wl1271_fetch_firmware(wl); |
| if (ret < 0) |
| goto out; |
| } |
| |
| /* No NVS from netlink, try to get it from the filesystem */ |
| if (wl->nvs == NULL) { |
| ret = wl1271_fetch_nvs(wl); |
| if (ret < 0) |
| goto out; |
| } |
| |
| out: |
| return ret; |
| } |
| |
| int wl1271_plt_start(struct wl1271 *wl) |
| { |
| int retries = WL1271_BOOT_RETRIES; |
| int ret; |
| |
| mutex_lock(&wl->mutex); |
| |
| wl1271_notice("power up"); |
| |
| if (wl->state != WL1271_STATE_OFF) { |
| wl1271_error("cannot go into PLT state because not " |
| "in off state: %d", wl->state); |
| ret = -EBUSY; |
| goto out; |
| } |
| |
| wl->bss_type = BSS_TYPE_STA_BSS; |
| |
| while (retries) { |
| retries--; |
| ret = wl1271_chip_wakeup(wl); |
| if (ret < 0) |
| goto power_off; |
| |
| ret = wl1271_boot(wl); |
| if (ret < 0) |
| goto power_off; |
| |
| ret = wl1271_plt_init(wl); |
| if (ret < 0) |
| goto irq_disable; |
| |
| wl->state = WL1271_STATE_PLT; |
| wl1271_notice("firmware booted in PLT mode (%s)", |
| wl->chip.fw_ver_str); |
| goto out; |
| |
| irq_disable: |
| wl1271_disable_interrupts(wl); |
| mutex_unlock(&wl->mutex); |
| /* Unlocking the mutex in the middle of handling is |
| inherently unsafe. In this case we deem it safe to do, |
| because we need to let any possibly pending IRQ out of |
| the system (and while we are WL1271_STATE_OFF the IRQ |
| work function will not do anything.) Also, any other |
| possible concurrent operations will fail due to the |
| current state, hence the wl1271 struct should be safe. */ |
| cancel_work_sync(&wl->irq_work); |
| mutex_lock(&wl->mutex); |
| power_off: |
| wl1271_power_off(wl); |
| } |
| |
| wl1271_error("firmware boot in PLT mode failed despite %d retries", |
| WL1271_BOOT_RETRIES); |
| out: |
| mutex_unlock(&wl->mutex); |
| |
| return ret; |
| } |
| |
| int __wl1271_plt_stop(struct wl1271 *wl) |
| { |
| int ret = 0; |
| |
| wl1271_notice("power down"); |
| |
| if (wl->state != WL1271_STATE_PLT) { |
| wl1271_error("cannot power down because not in PLT " |
| "state: %d", wl->state); |
| ret = -EBUSY; |
| goto out; |
| } |
| |
| wl1271_disable_interrupts(wl); |
| wl1271_power_off(wl); |
| |
| wl->state = WL1271_STATE_OFF; |
| wl->rx_counter = 0; |
| |
| mutex_unlock(&wl->mutex); |
| cancel_work_sync(&wl->irq_work); |
| cancel_work_sync(&wl->recovery_work); |
| mutex_lock(&wl->mutex); |
| out: |
| return ret; |
| } |
| |
| int wl1271_plt_stop(struct wl1271 *wl) |
| { |
| int ret; |
| |
| mutex_lock(&wl->mutex); |
| ret = __wl1271_plt_stop(wl); |
| mutex_unlock(&wl->mutex); |
| return ret; |
| } |
| |
| static int wl1271_op_tx(struct ieee80211_hw *hw, struct sk_buff *skb) |
| { |
| struct wl1271 *wl = hw->priv; |
| struct ieee80211_conf *conf = &hw->conf; |
| struct ieee80211_tx_info *txinfo = IEEE80211_SKB_CB(skb); |
| struct ieee80211_sta *sta = txinfo->control.sta; |
| unsigned long flags; |
| int q; |
| |
| /* |
| * peek into the rates configured in the STA entry. |
| * The rates set after connection stage, The first block only BG sets: |
| * the compare is for bit 0-16 of sta_rate_set. The second block add |
| * HT rates in case of HT supported. |
| */ |
| spin_lock_irqsave(&wl->wl_lock, flags); |
| if (sta && |
| (sta->supp_rates[conf->channel->band] != |
| (wl->sta_rate_set & HW_BG_RATES_MASK)) && |
| wl->bss_type != BSS_TYPE_AP_BSS) { |
| wl->sta_rate_set = sta->supp_rates[conf->channel->band]; |
| set_bit(WL1271_FLAG_STA_RATES_CHANGED, &wl->flags); |
| } |
| |
| #ifdef CONFIG_WL12XX_HT |
| if (sta && |
| sta->ht_cap.ht_supported && |
| ((wl->sta_rate_set >> HW_HT_RATES_OFFSET) != |
| sta->ht_cap.mcs.rx_mask[0])) { |
| /* Clean MCS bits before setting them */ |
| wl->sta_rate_set &= HW_BG_RATES_MASK; |
| wl->sta_rate_set |= |
| (sta->ht_cap.mcs.rx_mask[0] << HW_HT_RATES_OFFSET); |
| set_bit(WL1271_FLAG_STA_RATES_CHANGED, &wl->flags); |
| } |
| #endif |
| wl->tx_queue_count++; |
| spin_unlock_irqrestore(&wl->wl_lock, flags); |
| |
| /* queue the packet */ |
| q = wl1271_tx_get_queue(skb_get_queue_mapping(skb)); |
| skb_queue_tail(&wl->tx_queue[q], skb); |
| |
| /* |
| * The chip specific setup must run before the first TX packet - |
| * before that, the tx_work will not be initialized! |
| */ |
| |
| if (!test_bit(WL1271_FLAG_FW_TX_BUSY, &wl->flags)) |
| ieee80211_queue_work(wl->hw, &wl->tx_work); |
| |
| /* |
| * The workqueue is slow to process the tx_queue and we need stop |
| * the queue here, otherwise the queue will get too long. |
| */ |
| if (wl->tx_queue_count >= WL1271_TX_QUEUE_HIGH_WATERMARK) { |
| wl1271_debug(DEBUG_TX, "op_tx: stopping queues"); |
| |
| spin_lock_irqsave(&wl->wl_lock, flags); |
| ieee80211_stop_queues(wl->hw); |
| set_bit(WL1271_FLAG_TX_QUEUE_STOPPED, &wl->flags); |
| spin_unlock_irqrestore(&wl->wl_lock, flags); |
| } |
| |
| return NETDEV_TX_OK; |
| } |
| |
| static struct notifier_block wl1271_dev_notifier = { |
| .notifier_call = wl1271_dev_notify, |
| }; |
| |
| static int wl1271_op_start(struct ieee80211_hw *hw) |
| { |
| wl1271_debug(DEBUG_MAC80211, "mac80211 start"); |
| |
| /* |
| * We have to delay the booting of the hardware because |
| * we need to know the local MAC address before downloading and |
| * initializing the firmware. The MAC address cannot be changed |
| * after boot, and without the proper MAC address, the firmware |
| * will not function properly. |
| * |
| * The MAC address is first known when the corresponding interface |
| * is added. That is where we will initialize the hardware. |
| * |
| * In addition, we currently have different firmwares for AP and managed |
| * operation. We will know which to boot according to interface type. |
| */ |
| |
| return 0; |
| } |
| |
| static void wl1271_op_stop(struct ieee80211_hw *hw) |
| { |
| wl1271_debug(DEBUG_MAC80211, "mac80211 stop"); |
| } |
| |
| static int wl1271_op_add_interface(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct wl1271 *wl = hw->priv; |
| struct wiphy *wiphy = hw->wiphy; |
| int retries = WL1271_BOOT_RETRIES; |
| int ret = 0; |
| bool booted = false; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 add interface type %d mac %pM", |
| vif->type, vif->addr); |
| |
| mutex_lock(&wl->mutex); |
| if (wl->vif) { |
| wl1271_debug(DEBUG_MAC80211, |
| "multiple vifs are not supported yet"); |
| ret = -EBUSY; |
| goto out; |
| } |
| |
| switch (vif->type) { |
| case NL80211_IFTYPE_STATION: |
| wl->bss_type = BSS_TYPE_STA_BSS; |
| wl->set_bss_type = BSS_TYPE_STA_BSS; |
| break; |
| case NL80211_IFTYPE_ADHOC: |
| wl->bss_type = BSS_TYPE_IBSS; |
| wl->set_bss_type = BSS_TYPE_STA_BSS; |
| break; |
| case NL80211_IFTYPE_AP: |
| wl->bss_type = BSS_TYPE_AP_BSS; |
| break; |
| default: |
| ret = -EOPNOTSUPP; |
| goto out; |
| } |
| |
| memcpy(wl->mac_addr, vif->addr, ETH_ALEN); |
| |
| if (wl->state != WL1271_STATE_OFF) { |
| wl1271_error("cannot start because not in off state: %d", |
| wl->state); |
| ret = -EBUSY; |
| goto out; |
| } |
| |
| while (retries) { |
| retries--; |
| ret = wl1271_chip_wakeup(wl); |
| if (ret < 0) |
| goto power_off; |
| |
| ret = wl1271_boot(wl); |
| if (ret < 0) |
| goto power_off; |
| |
| ret = wl1271_hw_init(wl); |
| if (ret < 0) |
| goto irq_disable; |
| |
| booted = true; |
| break; |
| |
| irq_disable: |
| wl1271_disable_interrupts(wl); |
| mutex_unlock(&wl->mutex); |
| /* Unlocking the mutex in the middle of handling is |
| inherently unsafe. In this case we deem it safe to do, |
| because we need to let any possibly pending IRQ out of |
| the system (and while we are WL1271_STATE_OFF the IRQ |
| work function will not do anything.) Also, any other |
| possible concurrent operations will fail due to the |
| current state, hence the wl1271 struct should be safe. */ |
| cancel_work_sync(&wl->irq_work); |
| mutex_lock(&wl->mutex); |
| power_off: |
| wl1271_power_off(wl); |
| } |
| |
| if (!booted) { |
| wl1271_error("firmware boot failed despite %d retries", |
| WL1271_BOOT_RETRIES); |
| goto out; |
| } |
| |
| wl->vif = vif; |
| wl->state = WL1271_STATE_ON; |
| wl1271_info("firmware booted (%s)", wl->chip.fw_ver_str); |
| |
| /* update hw/fw version info in wiphy struct */ |
| wiphy->hw_version = wl->chip.id; |
| strncpy(wiphy->fw_version, wl->chip.fw_ver_str, |
| sizeof(wiphy->fw_version)); |
| |
| /* |
| * Now we know if 11a is supported (info from the NVS), so disable |
| * 11a channels if not supported |
| */ |
| if (!wl->enable_11a) |
| wiphy->bands[IEEE80211_BAND_5GHZ]->n_channels = 0; |
| |
| wl1271_debug(DEBUG_MAC80211, "11a is %ssupported", |
| wl->enable_11a ? "" : "not "); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| |
| if (!ret) |
| list_add(&wl->list, &wl_list); |
| |
| return ret; |
| } |
| |
| static void __wl1271_op_remove_interface(struct wl1271 *wl) |
| { |
| int i; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 remove interface"); |
| |
| wl1271_info("down"); |
| |
| list_del(&wl->list); |
| |
| WARN_ON(wl->state != WL1271_STATE_ON); |
| |
| /* enable dyn ps just in case (if left on due to fw crash etc) */ |
| if (wl->bss_type == BSS_TYPE_STA_BSS) |
| ieee80211_enable_dyn_ps(wl->vif); |
| |
| if (wl->scan.state != WL1271_SCAN_STATE_IDLE) { |
| wl->scan.state = WL1271_SCAN_STATE_IDLE; |
| kfree(wl->scan.scanned_ch); |
| wl->scan.scanned_ch = NULL; |
| wl->scan.req = NULL; |
| ieee80211_scan_completed(wl->hw, true); |
| } |
| |
| wl->state = WL1271_STATE_OFF; |
| |
| wl1271_disable_interrupts(wl); |
| |
| mutex_unlock(&wl->mutex); |
| |
| cancel_delayed_work_sync(&wl->scan_complete_work); |
| cancel_work_sync(&wl->irq_work); |
| cancel_work_sync(&wl->tx_work); |
| cancel_delayed_work_sync(&wl->pspoll_work); |
| cancel_delayed_work_sync(&wl->elp_work); |
| |
| mutex_lock(&wl->mutex); |
| |
| /* let's notify MAC80211 about the remaining pending TX frames */ |
| wl1271_tx_reset(wl); |
| wl1271_power_off(wl); |
| |
| memset(wl->bssid, 0, ETH_ALEN); |
| memset(wl->ssid, 0, IW_ESSID_MAX_SIZE + 1); |
| wl->ssid_len = 0; |
| wl->bss_type = MAX_BSS_TYPE; |
| wl->set_bss_type = MAX_BSS_TYPE; |
| wl->band = IEEE80211_BAND_2GHZ; |
| |
| wl->rx_counter = 0; |
| wl->psm_entry_retry = 0; |
| wl->power_level = WL1271_DEFAULT_POWER_LEVEL; |
| wl->tx_blocks_available = 0; |
| wl->tx_results_count = 0; |
| wl->tx_packets_count = 0; |
| wl->tx_security_last_seq = 0; |
| wl->tx_security_seq = 0; |
| wl->time_offset = 0; |
| wl->session_counter = 0; |
| wl->rate_set = CONF_TX_RATE_MASK_BASIC; |
| wl->sta_rate_set = 0; |
| wl->flags = 0; |
| wl->vif = NULL; |
| wl->filters = 0; |
| wl1271_free_ap_keys(wl); |
| memset(wl->ap_hlid_map, 0, sizeof(wl->ap_hlid_map)); |
| |
| for (i = 0; i < NUM_TX_QUEUES; i++) |
| wl->tx_blocks_freed[i] = 0; |
| |
| wl1271_debugfs_reset(wl); |
| |
| kfree(wl->fw_status); |
| wl->fw_status = NULL; |
| kfree(wl->tx_res_if); |
| wl->tx_res_if = NULL; |
| kfree(wl->target_mem_map); |
| wl->target_mem_map = NULL; |
| } |
| |
| static void wl1271_op_remove_interface(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct wl1271 *wl = hw->priv; |
| |
| mutex_lock(&wl->mutex); |
| /* |
| * wl->vif can be null here if someone shuts down the interface |
| * just when hardware recovery has been started. |
| */ |
| if (wl->vif) { |
| WARN_ON(wl->vif != vif); |
| __wl1271_op_remove_interface(wl); |
| } |
| |
| mutex_unlock(&wl->mutex); |
| cancel_work_sync(&wl->recovery_work); |
| } |
| |
| static void wl1271_configure_filters(struct wl1271 *wl, unsigned int filters) |
| { |
| wl1271_set_default_filters(wl); |
| |
| /* combine requested filters with current filter config */ |
| filters = wl->filters | filters; |
| |
| wl1271_debug(DEBUG_FILTERS, "RX filters set: "); |
| |
| if (filters & FIF_PROMISC_IN_BSS) { |
| wl1271_debug(DEBUG_FILTERS, " - FIF_PROMISC_IN_BSS"); |
| wl->rx_config &= ~CFG_UNI_FILTER_EN; |
| wl->rx_config |= CFG_BSSID_FILTER_EN; |
| } |
| if (filters & FIF_BCN_PRBRESP_PROMISC) { |
| wl1271_debug(DEBUG_FILTERS, " - FIF_BCN_PRBRESP_PROMISC"); |
| wl->rx_config &= ~CFG_BSSID_FILTER_EN; |
| wl->rx_config &= ~CFG_SSID_FILTER_EN; |
| } |
| if (filters & FIF_OTHER_BSS) { |
| wl1271_debug(DEBUG_FILTERS, " - FIF_OTHER_BSS"); |
| wl->rx_config &= ~CFG_BSSID_FILTER_EN; |
| } |
| if (filters & FIF_CONTROL) { |
| wl1271_debug(DEBUG_FILTERS, " - FIF_CONTROL"); |
| wl->rx_filter |= CFG_RX_CTL_EN; |
| } |
| if (filters & FIF_FCSFAIL) { |
| wl1271_debug(DEBUG_FILTERS, " - FIF_FCSFAIL"); |
| wl->rx_filter |= CFG_RX_FCS_ERROR; |
| } |
| } |
| |
| static int wl1271_dummy_join(struct wl1271 *wl) |
| { |
| int ret = 0; |
| /* we need to use a dummy BSSID for now */ |
| static const u8 dummy_bssid[ETH_ALEN] = { 0x0b, 0xad, 0xde, |
| 0xad, 0xbe, 0xef }; |
| |
| memcpy(wl->bssid, dummy_bssid, ETH_ALEN); |
| |
| /* pass through frames from all BSS */ |
| wl1271_configure_filters(wl, FIF_OTHER_BSS); |
| |
| ret = wl1271_cmd_join(wl, wl->set_bss_type); |
| if (ret < 0) |
| goto out; |
| |
| set_bit(WL1271_FLAG_JOINED, &wl->flags); |
| |
| out: |
| return ret; |
| } |
| |
| static int wl1271_join(struct wl1271 *wl, bool set_assoc) |
| { |
| int ret; |
| |
| /* |
| * One of the side effects of the JOIN command is that is clears |
| * WPA/WPA2 keys from the chipset. Performing a JOIN while associated |
| * to a WPA/WPA2 access point will therefore kill the data-path. |
| * Currently there is no supported scenario for JOIN during |
| * association - if it becomes a supported scenario, the WPA/WPA2 keys |
| * must be handled somehow. |
| * |
| */ |
| if (test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags)) |
| wl1271_info("JOIN while associated."); |
| |
| if (set_assoc) |
| set_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags); |
| |
| ret = wl1271_cmd_join(wl, wl->set_bss_type); |
| if (ret < 0) |
| goto out; |
| |
| set_bit(WL1271_FLAG_JOINED, &wl->flags); |
| |
| if (!test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags)) |
| goto out; |
| |
| /* |
| * The join command disable the keep-alive mode, shut down its process, |
| * and also clear the template config, so we need to reset it all after |
| * the join. The acx_aid starts the keep-alive process, and the order |
| * of the commands below is relevant. |
| */ |
| ret = wl1271_acx_keep_alive_mode(wl, true); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_acx_aid(wl, wl->aid); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_cmd_build_klv_null_data(wl); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_acx_keep_alive_config(wl, CMD_TEMPL_KLV_IDX_NULL_DATA, |
| ACX_KEEP_ALIVE_TPL_VALID); |
| if (ret < 0) |
| goto out; |
| |
| out: |
| return ret; |
| } |
| |
| static int wl1271_unjoin(struct wl1271 *wl) |
| { |
| int ret; |
| |
| /* to stop listening to a channel, we disconnect */ |
| ret = wl1271_cmd_disconnect(wl); |
| if (ret < 0) |
| goto out; |
| |
| clear_bit(WL1271_FLAG_JOINED, &wl->flags); |
| memset(wl->bssid, 0, ETH_ALEN); |
| |
| /* stop filterting packets based on bssid */ |
| wl1271_configure_filters(wl, FIF_OTHER_BSS); |
| |
| out: |
| return ret; |
| } |
| |
| static void wl1271_set_band_rate(struct wl1271 *wl) |
| { |
| if (wl->band == IEEE80211_BAND_2GHZ) |
| wl->basic_rate_set = wl->conf.tx.basic_rate; |
| else |
| wl->basic_rate_set = wl->conf.tx.basic_rate_5; |
| } |
| |
| static int wl1271_sta_handle_idle(struct wl1271 *wl, bool idle) |
| { |
| int ret; |
| |
| if (idle) { |
| if (test_bit(WL1271_FLAG_JOINED, &wl->flags)) { |
| ret = wl1271_unjoin(wl); |
| if (ret < 0) |
| goto out; |
| } |
| wl->rate_set = wl1271_tx_min_rate_get(wl); |
| wl->sta_rate_set = 0; |
| ret = wl1271_acx_sta_rate_policies(wl); |
| if (ret < 0) |
| goto out; |
| ret = wl1271_acx_keep_alive_config( |
| wl, CMD_TEMPL_KLV_IDX_NULL_DATA, |
| ACX_KEEP_ALIVE_TPL_INVALID); |
| if (ret < 0) |
| goto out; |
| set_bit(WL1271_FLAG_IDLE, &wl->flags); |
| } else { |
| /* increment the session counter */ |
| wl->session_counter++; |
| if (wl->session_counter >= SESSION_COUNTER_MAX) |
| wl->session_counter = 0; |
| ret = wl1271_dummy_join(wl); |
| if (ret < 0) |
| goto out; |
| clear_bit(WL1271_FLAG_IDLE, &wl->flags); |
| } |
| |
| out: |
| return ret; |
| } |
| |
| static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed) |
| { |
| struct wl1271 *wl = hw->priv; |
| struct ieee80211_conf *conf = &hw->conf; |
| int channel, ret = 0; |
| bool is_ap; |
| |
| channel = ieee80211_frequency_to_channel(conf->channel->center_freq); |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 config ch %d psm %s power %d %s" |
| " changed 0x%x", |
| channel, |
| conf->flags & IEEE80211_CONF_PS ? "on" : "off", |
| conf->power_level, |
| conf->flags & IEEE80211_CONF_IDLE ? "idle" : "in use", |
| changed); |
| |
| /* |
| * mac80211 will go to idle nearly immediately after transmitting some |
| * frames, such as the deauth. To make sure those frames reach the air, |
| * wait here until the TX queue is fully flushed. |
| */ |
| if ((changed & IEEE80211_CONF_CHANGE_IDLE) && |
| (conf->flags & IEEE80211_CONF_IDLE)) |
| wl1271_tx_flush(wl); |
| |
| mutex_lock(&wl->mutex); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) { |
| ret = -EAGAIN; |
| goto out; |
| } |
| |
| is_ap = (wl->bss_type == BSS_TYPE_AP_BSS); |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| /* if the channel changes while joined, join again */ |
| if (changed & IEEE80211_CONF_CHANGE_CHANNEL && |
| ((wl->band != conf->channel->band) || |
| (wl->channel != channel))) { |
| wl->band = conf->channel->band; |
| wl->channel = channel; |
| |
| if (!is_ap) { |
| /* |
| * FIXME: the mac80211 should really provide a fixed |
| * rate to use here. for now, just use the smallest |
| * possible rate for the band as a fixed rate for |
| * association frames and other control messages. |
| */ |
| if (!test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags)) |
| wl1271_set_band_rate(wl); |
| |
| wl->basic_rate = wl1271_tx_min_rate_get(wl); |
| ret = wl1271_acx_sta_rate_policies(wl); |
| if (ret < 0) |
| wl1271_warning("rate policy for channel " |
| "failed %d", ret); |
| |
| if (test_bit(WL1271_FLAG_JOINED, &wl->flags)) { |
| ret = wl1271_join(wl, false); |
| if (ret < 0) |
| wl1271_warning("cmd join on channel " |
| "failed %d", ret); |
| } |
| } |
| } |
| |
| if (changed & IEEE80211_CONF_CHANGE_IDLE && !is_ap) { |
| ret = wl1271_sta_handle_idle(wl, |
| conf->flags & IEEE80211_CONF_IDLE); |
| if (ret < 0) |
| wl1271_warning("idle mode change failed %d", ret); |
| } |
| |
| /* |
| * if mac80211 changes the PSM mode, make sure the mode is not |
| * incorrectly changed after the pspoll failure active window. |
| */ |
| if (changed & IEEE80211_CONF_CHANGE_PS) |
| clear_bit(WL1271_FLAG_PSPOLL_FAILURE, &wl->flags); |
| |
| if (conf->flags & IEEE80211_CONF_PS && |
| !test_bit(WL1271_FLAG_PSM_REQUESTED, &wl->flags)) { |
| set_bit(WL1271_FLAG_PSM_REQUESTED, &wl->flags); |
| |
| /* |
| * We enter PSM only if we're already associated. |
| * If we're not, we'll enter it when joining an SSID, |
| * through the bss_info_changed() hook. |
| */ |
| if (test_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags)) { |
| wl1271_debug(DEBUG_PSM, "psm enabled"); |
| ret = wl1271_ps_set_mode(wl, STATION_POWER_SAVE_MODE, |
| wl->basic_rate, true); |
| } |
| } else if (!(conf->flags & IEEE80211_CONF_PS) && |
| test_bit(WL1271_FLAG_PSM_REQUESTED, &wl->flags)) { |
| wl1271_debug(DEBUG_PSM, "psm disabled"); |
| |
| clear_bit(WL1271_FLAG_PSM_REQUESTED, &wl->flags); |
| |
| if (test_bit(WL1271_FLAG_PSM, &wl->flags)) |
| ret = wl1271_ps_set_mode(wl, STATION_ACTIVE_MODE, |
| wl->basic_rate, true); |
| } |
| |
| if (conf->power_level != wl->power_level) { |
| ret = wl1271_acx_tx_power(wl, conf->power_level); |
| if (ret < 0) |
| goto out_sleep; |
| |
| wl->power_level = conf->power_level; |
| } |
| |
| out_sleep: |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| |
| return ret; |
| } |
| |
| struct wl1271_filter_params { |
| bool enabled; |
| int mc_list_length; |
| u8 mc_list[ACX_MC_ADDRESS_GROUP_MAX][ETH_ALEN]; |
| }; |
| |
| static u64 wl1271_op_prepare_multicast(struct ieee80211_hw *hw, |
| struct netdev_hw_addr_list *mc_list) |
| { |
| struct wl1271_filter_params *fp; |
| struct netdev_hw_addr *ha; |
| struct wl1271 *wl = hw->priv; |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) |
| return 0; |
| |
| fp = kzalloc(sizeof(*fp), GFP_ATOMIC); |
| if (!fp) { |
| wl1271_error("Out of memory setting filters."); |
| return 0; |
| } |
| |
| /* update multicast filtering parameters */ |
| fp->mc_list_length = 0; |
| if (netdev_hw_addr_list_count(mc_list) > ACX_MC_ADDRESS_GROUP_MAX) { |
| fp->enabled = false; |
| } else { |
| fp->enabled = true; |
| netdev_hw_addr_list_for_each(ha, mc_list) { |
| memcpy(fp->mc_list[fp->mc_list_length], |
| ha->addr, ETH_ALEN); |
| fp->mc_list_length++; |
| } |
| } |
| |
| return (u64)(unsigned long)fp; |
| } |
| |
| #define WL1271_SUPPORTED_FILTERS (FIF_PROMISC_IN_BSS | \ |
| FIF_ALLMULTI | \ |
| FIF_FCSFAIL | \ |
| FIF_BCN_PRBRESP_PROMISC | \ |
| FIF_CONTROL | \ |
| FIF_OTHER_BSS) |
| |
| static void wl1271_op_configure_filter(struct ieee80211_hw *hw, |
| unsigned int changed, |
| unsigned int *total, u64 multicast) |
| { |
| struct wl1271_filter_params *fp = (void *)(unsigned long)multicast; |
| struct wl1271 *wl = hw->priv; |
| int ret; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 configure filter changed %x" |
| " total %x", changed, *total); |
| |
| mutex_lock(&wl->mutex); |
| |
| *total &= WL1271_SUPPORTED_FILTERS; |
| changed &= WL1271_SUPPORTED_FILTERS; |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) |
| goto out; |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| if (wl->bss_type != BSS_TYPE_AP_BSS) { |
| if (*total & FIF_ALLMULTI) |
| ret = wl1271_acx_group_address_tbl(wl, false, NULL, 0); |
| else if (fp) |
| ret = wl1271_acx_group_address_tbl(wl, fp->enabled, |
| fp->mc_list, |
| fp->mc_list_length); |
| if (ret < 0) |
| goto out_sleep; |
| } |
| |
| /* determine, whether supported filter values have changed */ |
| if (changed == 0) |
| goto out_sleep; |
| |
| /* configure filters */ |
| wl->filters = *total; |
| wl1271_configure_filters(wl, 0); |
| |
| /* apply configured filters */ |
| ret = wl1271_acx_rx_config(wl, wl->rx_config, wl->rx_filter); |
| if (ret < 0) |
| goto out_sleep; |
| |
| out_sleep: |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| kfree(fp); |
| } |
| |
| static int wl1271_record_ap_key(struct wl1271 *wl, u8 id, u8 key_type, |
| u8 key_size, const u8 *key, u8 hlid, u32 tx_seq_32, |
| u16 tx_seq_16) |
| { |
| struct wl1271_ap_key *ap_key; |
| int i; |
| |
| wl1271_debug(DEBUG_CRYPT, "record ap key id %d", (int)id); |
| |
| if (key_size > MAX_KEY_SIZE) |
| return -EINVAL; |
| |
| /* |
| * Find next free entry in ap_keys. Also check we are not replacing |
| * an existing key. |
| */ |
| for (i = 0; i < MAX_NUM_KEYS; i++) { |
| if (wl->recorded_ap_keys[i] == NULL) |
| break; |
| |
| if (wl->recorded_ap_keys[i]->id == id) { |
| wl1271_warning("trying to record key replacement"); |
| return -EINVAL; |
| } |
| } |
| |
| if (i == MAX_NUM_KEYS) |
| return -EBUSY; |
| |
| ap_key = kzalloc(sizeof(*ap_key), GFP_KERNEL); |
| if (!ap_key) |
| return -ENOMEM; |
| |
| ap_key->id = id; |
| ap_key->key_type = key_type; |
| ap_key->key_size = key_size; |
| memcpy(ap_key->key, key, key_size); |
| ap_key->hlid = hlid; |
| ap_key->tx_seq_32 = tx_seq_32; |
| ap_key->tx_seq_16 = tx_seq_16; |
| |
| wl->recorded_ap_keys[i] = ap_key; |
| return 0; |
| } |
| |
| static void wl1271_free_ap_keys(struct wl1271 *wl) |
| { |
| int i; |
| |
| for (i = 0; i < MAX_NUM_KEYS; i++) { |
| kfree(wl->recorded_ap_keys[i]); |
| wl->recorded_ap_keys[i] = NULL; |
| } |
| } |
| |
| static int wl1271_ap_init_hwenc(struct wl1271 *wl) |
| { |
| int i, ret = 0; |
| struct wl1271_ap_key *key; |
| bool wep_key_added = false; |
| |
| for (i = 0; i < MAX_NUM_KEYS; i++) { |
| if (wl->recorded_ap_keys[i] == NULL) |
| break; |
| |
| key = wl->recorded_ap_keys[i]; |
| ret = wl1271_cmd_set_ap_key(wl, KEY_ADD_OR_REPLACE, |
| key->id, key->key_type, |
| key->key_size, key->key, |
| key->hlid, key->tx_seq_32, |
| key->tx_seq_16); |
| if (ret < 0) |
| goto out; |
| |
| if (key->key_type == KEY_WEP) |
| wep_key_added = true; |
| } |
| |
| if (wep_key_added) { |
| ret = wl1271_cmd_set_ap_default_wep_key(wl, wl->default_key); |
| if (ret < 0) |
| goto out; |
| } |
| |
| out: |
| wl1271_free_ap_keys(wl); |
| return ret; |
| } |
| |
| static int wl1271_set_key(struct wl1271 *wl, u16 action, u8 id, u8 key_type, |
| u8 key_size, const u8 *key, u32 tx_seq_32, |
| u16 tx_seq_16, struct ieee80211_sta *sta) |
| { |
| int ret; |
| bool is_ap = (wl->bss_type == BSS_TYPE_AP_BSS); |
| |
| if (is_ap) { |
| struct wl1271_station *wl_sta; |
| u8 hlid; |
| |
| if (sta) { |
| wl_sta = (struct wl1271_station *)sta->drv_priv; |
| hlid = wl_sta->hlid; |
| } else { |
| hlid = WL1271_AP_BROADCAST_HLID; |
| } |
| |
| if (!test_bit(WL1271_FLAG_AP_STARTED, &wl->flags)) { |
| /* |
| * We do not support removing keys after AP shutdown. |
| * Pretend we do to make mac80211 happy. |
| */ |
| if (action != KEY_ADD_OR_REPLACE) |
| return 0; |
| |
| ret = wl1271_record_ap_key(wl, id, |
| key_type, key_size, |
| key, hlid, tx_seq_32, |
| tx_seq_16); |
| } else { |
| ret = wl1271_cmd_set_ap_key(wl, action, |
| id, key_type, key_size, |
| key, hlid, tx_seq_32, |
| tx_seq_16); |
| } |
| |
| if (ret < 0) |
| return ret; |
| } else { |
| const u8 *addr; |
| static const u8 bcast_addr[ETH_ALEN] = { |
| 0xff, 0xff, 0xff, 0xff, 0xff, 0xff |
| }; |
| |
| addr = sta ? sta->addr : bcast_addr; |
| |
| if (is_zero_ether_addr(addr)) { |
| /* We dont support TX only encryption */ |
| return -EOPNOTSUPP; |
| } |
| |
| /* The wl1271 does not allow to remove unicast keys - they |
| will be cleared automatically on next CMD_JOIN. Ignore the |
| request silently, as we dont want the mac80211 to emit |
| an error message. */ |
| if (action == KEY_REMOVE && !is_broadcast_ether_addr(addr)) |
| return 0; |
| |
| ret = wl1271_cmd_set_sta_key(wl, action, |
| id, key_type, key_size, |
| key, addr, tx_seq_32, |
| tx_seq_16); |
| if (ret < 0) |
| return ret; |
| |
| /* the default WEP key needs to be configured at least once */ |
| if (key_type == KEY_WEP) { |
| ret = wl1271_cmd_set_sta_default_wep_key(wl, |
| wl->default_key); |
| if (ret < 0) |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int wl1271_op_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct ieee80211_key_conf *key_conf) |
| { |
| struct wl1271 *wl = hw->priv; |
| int ret; |
| u32 tx_seq_32 = 0; |
| u16 tx_seq_16 = 0; |
| u8 key_type; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 set key"); |
| |
| wl1271_debug(DEBUG_CRYPT, "CMD: 0x%x sta: %p", cmd, sta); |
| wl1271_debug(DEBUG_CRYPT, "Key: algo:0x%x, id:%d, len:%d flags 0x%x", |
| key_conf->cipher, key_conf->keyidx, |
| key_conf->keylen, key_conf->flags); |
| wl1271_dump(DEBUG_CRYPT, "KEY: ", key_conf->key, key_conf->keylen); |
| |
| mutex_lock(&wl->mutex); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) { |
| ret = -EAGAIN; |
| goto out_unlock; |
| } |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out_unlock; |
| |
| switch (key_conf->cipher) { |
| case WLAN_CIPHER_SUITE_WEP40: |
| case WLAN_CIPHER_SUITE_WEP104: |
| key_type = KEY_WEP; |
| |
| key_conf->hw_key_idx = key_conf->keyidx; |
| break; |
| case WLAN_CIPHER_SUITE_TKIP: |
| key_type = KEY_TKIP; |
| |
| key_conf->hw_key_idx = key_conf->keyidx; |
| tx_seq_32 = WL1271_TX_SECURITY_HI32(wl->tx_security_seq); |
| tx_seq_16 = WL1271_TX_SECURITY_LO16(wl->tx_security_seq); |
| break; |
| case WLAN_CIPHER_SUITE_CCMP: |
| key_type = KEY_AES; |
| |
| key_conf->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| tx_seq_32 = WL1271_TX_SECURITY_HI32(wl->tx_security_seq); |
| tx_seq_16 = WL1271_TX_SECURITY_LO16(wl->tx_security_seq); |
| break; |
| case WL1271_CIPHER_SUITE_GEM: |
| key_type = KEY_GEM; |
| tx_seq_32 = WL1271_TX_SECURITY_HI32(wl->tx_security_seq); |
| tx_seq_16 = WL1271_TX_SECURITY_LO16(wl->tx_security_seq); |
| break; |
| default: |
| wl1271_error("Unknown key algo 0x%x", key_conf->cipher); |
| |
| ret = -EOPNOTSUPP; |
| goto out_sleep; |
| } |
| |
| switch (cmd) { |
| case SET_KEY: |
| ret = wl1271_set_key(wl, KEY_ADD_OR_REPLACE, |
| key_conf->keyidx, key_type, |
| key_conf->keylen, key_conf->key, |
| tx_seq_32, tx_seq_16, sta); |
| if (ret < 0) { |
| wl1271_error("Could not add or replace key"); |
| goto out_sleep; |
| } |
| break; |
| |
| case DISABLE_KEY: |
| ret = wl1271_set_key(wl, KEY_REMOVE, |
| key_conf->keyidx, key_type, |
| key_conf->keylen, key_conf->key, |
| 0, 0, sta); |
| if (ret < 0) { |
| wl1271_error("Could not remove key"); |
| goto out_sleep; |
| } |
| break; |
| |
| default: |
| wl1271_error("Unsupported key cmd 0x%x", cmd); |
| ret = -EOPNOTSUPP; |
| break; |
| } |
| |
| out_sleep: |
| wl1271_ps_elp_sleep(wl); |
| |
| out_unlock: |
| mutex_unlock(&wl->mutex); |
| |
| return ret; |
| } |
| |
| static int wl1271_op_hw_scan(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct cfg80211_scan_request *req) |
| { |
| struct wl1271 *wl = hw->priv; |
| int ret; |
| u8 *ssid = NULL; |
| size_t len = 0; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 hw scan"); |
| |
| if (req->n_ssids) { |
| ssid = req->ssids[0].ssid; |
| len = req->ssids[0].ssid_len; |
| } |
| |
| mutex_lock(&wl->mutex); |
| |
| if (wl->state == WL1271_STATE_OFF) { |
| /* |
| * We cannot return -EBUSY here because cfg80211 will expect |
| * a call to ieee80211_scan_completed if we do - in this case |
| * there won't be any call. |
| */ |
| ret = -EAGAIN; |
| goto out; |
| } |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_scan(hw->priv, ssid, len, req); |
| |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| |
| return ret; |
| } |
| |
| static int wl1271_op_set_frag_threshold(struct ieee80211_hw *hw, u32 value) |
| { |
| struct wl1271 *wl = hw->priv; |
| int ret = 0; |
| |
| mutex_lock(&wl->mutex); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) { |
| ret = -EAGAIN; |
| goto out; |
| } |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_acx_frag_threshold(wl, (u16)value); |
| if (ret < 0) |
| wl1271_warning("wl1271_op_set_frag_threshold failed: %d", ret); |
| |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| |
| return ret; |
| } |
| |
| static int wl1271_op_set_rts_threshold(struct ieee80211_hw *hw, u32 value) |
| { |
| struct wl1271 *wl = hw->priv; |
| int ret = 0; |
| |
| mutex_lock(&wl->mutex); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) { |
| ret = -EAGAIN; |
| goto out; |
| } |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_acx_rts_threshold(wl, (u16) value); |
| if (ret < 0) |
| wl1271_warning("wl1271_op_set_rts_threshold failed: %d", ret); |
| |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| |
| return ret; |
| } |
| |
| static int wl1271_ssid_set(struct wl1271 *wl, struct sk_buff *skb, |
| int offset) |
| { |
| u8 *ptr = skb->data + offset; |
| |
| /* find the location of the ssid in the beacon */ |
| while (ptr < skb->data + skb->len) { |
| if (ptr[0] == WLAN_EID_SSID) { |
| wl->ssid_len = ptr[1]; |
| memcpy(wl->ssid, ptr+2, wl->ssid_len); |
| return 0; |
| } |
| ptr += (ptr[1] + 2); |
| } |
| |
| wl1271_error("No SSID in IEs!\n"); |
| return -ENOENT; |
| } |
| |
| static int wl1271_bss_erp_info_changed(struct wl1271 *wl, |
| struct ieee80211_bss_conf *bss_conf, |
| u32 changed) |
| { |
| int ret = 0; |
| |
| if (changed & BSS_CHANGED_ERP_SLOT) { |
| if (bss_conf->use_short_slot) |
| ret = wl1271_acx_slot(wl, SLOT_TIME_SHORT); |
| else |
| ret = wl1271_acx_slot(wl, SLOT_TIME_LONG); |
| if (ret < 0) { |
| wl1271_warning("Set slot time failed %d", ret); |
| goto out; |
| } |
| } |
| |
| if (changed & BSS_CHANGED_ERP_PREAMBLE) { |
| if (bss_conf->use_short_preamble) |
| wl1271_acx_set_preamble(wl, ACX_PREAMBLE_SHORT); |
| else |
| wl1271_acx_set_preamble(wl, ACX_PREAMBLE_LONG); |
| } |
| |
| if (changed & BSS_CHANGED_ERP_CTS_PROT) { |
| if (bss_conf->use_cts_prot) |
| ret = wl1271_acx_cts_protect(wl, CTSPROTECT_ENABLE); |
| else |
| ret = wl1271_acx_cts_protect(wl, CTSPROTECT_DISABLE); |
| if (ret < 0) { |
| wl1271_warning("Set ctsprotect failed %d", ret); |
| goto out; |
| } |
| } |
| |
| out: |
| return ret; |
| } |
| |
| static int wl1271_bss_beacon_info_changed(struct wl1271 *wl, |
| struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *bss_conf, |
| u32 changed) |
| { |
| bool is_ap = (wl->bss_type == BSS_TYPE_AP_BSS); |
| int ret = 0; |
| |
| if ((changed & BSS_CHANGED_BEACON_INT)) { |
| wl1271_debug(DEBUG_MASTER, "beacon interval updated: %d", |
| bss_conf->beacon_int); |
| |
| wl->beacon_int = bss_conf->beacon_int; |
| } |
| |
| if ((changed & BSS_CHANGED_BEACON)) { |
| struct ieee80211_hdr *hdr; |
| int ieoffset = offsetof(struct ieee80211_mgmt, |
| u.beacon.variable); |
| struct sk_buff *beacon = ieee80211_beacon_get(wl->hw, vif); |
| u16 tmpl_id; |
| |
| if (!beacon) |
| goto out; |
| |
| wl1271_debug(DEBUG_MASTER, "beacon updated"); |
| |
| ret = wl1271_ssid_set(wl, beacon, ieoffset); |
| if (ret < 0) { |
| dev_kfree_skb(beacon); |
| goto out; |
| } |
| tmpl_id = is_ap ? CMD_TEMPL_AP_BEACON : |
| CMD_TEMPL_BEACON; |
| ret = wl1271_cmd_template_set(wl, tmpl_id, |
| beacon->data, |
| beacon->len, 0, |
| wl1271_tx_min_rate_get(wl)); |
| if (ret < 0) { |
| dev_kfree_skb(beacon); |
| goto out; |
| } |
| |
| hdr = (struct ieee80211_hdr *) beacon->data; |
| hdr->frame_control = cpu_to_le16(IEEE80211_FTYPE_MGMT | |
| IEEE80211_STYPE_PROBE_RESP); |
| |
| tmpl_id = is_ap ? CMD_TEMPL_AP_PROBE_RESPONSE : |
| CMD_TEMPL_PROBE_RESPONSE; |
| ret = wl1271_cmd_template_set(wl, |
| tmpl_id, |
| beacon->data, |
| beacon->len, 0, |
| wl1271_tx_min_rate_get(wl)); |
| dev_kfree_skb(beacon); |
| if (ret < 0) |
| goto out; |
| } |
| |
| out: |
| return ret; |
| } |
| |
| /* AP mode changes */ |
| static void wl1271_bss_info_changed_ap(struct wl1271 *wl, |
| struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *bss_conf, |
| u32 changed) |
| { |
| int ret = 0; |
| |
| if ((changed & BSS_CHANGED_BASIC_RATES)) { |
| u32 rates = bss_conf->basic_rates; |
| struct conf_tx_rate_class mgmt_rc; |
| |
| wl->basic_rate_set = wl1271_tx_enabled_rates_get(wl, rates); |
| wl->basic_rate = wl1271_tx_min_rate_get(wl); |
| wl1271_debug(DEBUG_AP, "basic rates: 0x%x", |
| wl->basic_rate_set); |
| |
| /* update the AP management rate policy with the new rates */ |
| mgmt_rc.enabled_rates = wl->basic_rate_set; |
| mgmt_rc.long_retry_limit = 10; |
| mgmt_rc.short_retry_limit = 10; |
| mgmt_rc.aflags = 0; |
| ret = wl1271_acx_ap_rate_policy(wl, &mgmt_rc, |
| ACX_TX_AP_MODE_MGMT_RATE); |
| if (ret < 0) { |
| wl1271_error("AP mgmt policy change failed %d", ret); |
| goto out; |
| } |
| } |
| |
| ret = wl1271_bss_beacon_info_changed(wl, vif, bss_conf, changed); |
| if (ret < 0) |
| goto out; |
| |
| if ((changed & BSS_CHANGED_BEACON_ENABLED)) { |
| if (bss_conf->enable_beacon) { |
| if (!test_bit(WL1271_FLAG_AP_STARTED, &wl->flags)) { |
| ret = wl1271_cmd_start_bss(wl); |
| if (ret < 0) |
| goto out; |
| |
| set_bit(WL1271_FLAG_AP_STARTED, &wl->flags); |
| wl1271_debug(DEBUG_AP, "started AP"); |
| |
| ret = wl1271_ap_init_hwenc(wl); |
| if (ret < 0) |
| goto out; |
| } |
| } else { |
| if (test_bit(WL1271_FLAG_AP_STARTED, &wl->flags)) { |
| ret = wl1271_cmd_stop_bss(wl); |
| if (ret < 0) |
| goto out; |
| |
| clear_bit(WL1271_FLAG_AP_STARTED, &wl->flags); |
| wl1271_debug(DEBUG_AP, "stopped AP"); |
| } |
| } |
| } |
| |
| ret = wl1271_bss_erp_info_changed(wl, bss_conf, changed); |
| if (ret < 0) |
| goto out; |
| out: |
| return; |
| } |
| |
| /* STA/IBSS mode changes */ |
| static void wl1271_bss_info_changed_sta(struct wl1271 *wl, |
| struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *bss_conf, |
| u32 changed) |
| { |
| bool do_join = false, set_assoc = false; |
| bool is_ibss = (wl->bss_type == BSS_TYPE_IBSS); |
| int ret; |
| struct ieee80211_sta *sta; |
| |
| if (is_ibss) { |
| ret = wl1271_bss_beacon_info_changed(wl, vif, bss_conf, |
| changed); |
| if (ret < 0) |
| goto out; |
| } |
| |
| if ((changed & BSS_CHANGED_BEACON_INT) && is_ibss) |
| do_join = true; |
| |
| /* Need to update the SSID (for filtering etc) */ |
| if ((changed & BSS_CHANGED_BEACON) && is_ibss) |
| do_join = true; |
| |
| if ((changed & BSS_CHANGED_BEACON_ENABLED) && is_ibss) { |
| wl1271_debug(DEBUG_ADHOC, "ad-hoc beaconing: %s", |
| bss_conf->enable_beacon ? "enabled" : "disabled"); |
| |
| if (bss_conf->enable_beacon) |
| wl->set_bss_type = BSS_TYPE_IBSS; |
| else |
| wl->set_bss_type = BSS_TYPE_STA_BSS; |
| do_join = true; |
| } |
| |
| if ((changed & BSS_CHANGED_CQM)) { |
| bool enable = false; |
| if (bss_conf->cqm_rssi_thold) |
| enable = true; |
| ret = wl1271_acx_rssi_snr_trigger(wl, enable, |
| bss_conf->cqm_rssi_thold, |
| bss_conf->cqm_rssi_hyst); |
| if (ret < 0) |
| goto out; |
| wl->rssi_thold = bss_conf->cqm_rssi_thold; |
| } |
| |
| if ((changed & BSS_CHANGED_BSSID) && |
| /* |
| * Now we know the correct bssid, so we send a new join command |
| * and enable the BSSID filter |
| */ |
| memcmp(wl->bssid, bss_conf->bssid, ETH_ALEN)) { |
| memcpy(wl->bssid, bss_conf->bssid, ETH_ALEN); |
| |
| if (!is_zero_ether_addr(wl->bssid)) { |
| ret = wl1271_cmd_build_null_data(wl); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_build_qos_null_data(wl); |
| if (ret < 0) |
| goto out; |
| |
| /* filter out all packets not from this BSSID */ |
| wl1271_configure_filters(wl, 0); |
| |
| /* Need to update the BSSID (for filtering etc) */ |
| do_join = true; |
| } |
| } |
| |
| if ((changed & BSS_CHANGED_ASSOC)) { |
| if (bss_conf->assoc) { |
| u32 rates; |
| int ieoffset; |
| wl->aid = bss_conf->aid; |
| set_assoc = true; |
| |
| wl->ps_poll_failures = 0; |
| |
| /* |
| * use basic rates from AP, and determine lowest rate |
| * to use with control frames. |
| */ |
| rates = bss_conf->basic_rates; |
| wl->basic_rate_set = wl1271_tx_enabled_rates_get(wl, |
| rates); |
| wl->basic_rate = wl1271_tx_min_rate_get(wl); |
| ret = wl1271_acx_sta_rate_policies(wl); |
| if (ret < 0) |
| goto out; |
| |
| /* |
| * with wl1271, we don't need to update the |
| * beacon_int and dtim_period, because the firmware |
| * updates it by itself when the first beacon is |
| * received after a join. |
| */ |
| ret = wl1271_cmd_build_ps_poll(wl, wl->aid); |
| if (ret < 0) |
| goto out; |
| |
| /* |
| * Get a template for hardware connection maintenance |
| */ |
| dev_kfree_skb(wl->probereq); |
| wl->probereq = wl1271_cmd_build_ap_probe_req(wl, NULL); |
| ieoffset = offsetof(struct ieee80211_mgmt, |
| u.probe_req.variable); |
| wl1271_ssid_set(wl, wl->probereq, ieoffset); |
| |
| /* enable the connection monitoring feature */ |
| ret = wl1271_acx_conn_monit_params(wl, true); |
| if (ret < 0) |
| goto out; |
| |
| /* If we want to go in PSM but we're not there yet */ |
| if (test_bit(WL1271_FLAG_PSM_REQUESTED, &wl->flags) && |
| !test_bit(WL1271_FLAG_PSM, &wl->flags)) { |
| enum wl1271_cmd_ps_mode mode; |
| |
| mode = STATION_POWER_SAVE_MODE; |
| ret = wl1271_ps_set_mode(wl, mode, |
| wl->basic_rate, |
| true); |
| if (ret < 0) |
| goto out; |
| } |
| } else { |
| /* use defaults when not associated */ |
| clear_bit(WL1271_FLAG_STA_STATE_SENT, &wl->flags); |
| clear_bit(WL1271_FLAG_STA_ASSOCIATED, &wl->flags); |
| wl->aid = 0; |
| |
| /* free probe-request template */ |
| dev_kfree_skb(wl->probereq); |
| wl->probereq = NULL; |
| |
| /* re-enable dynamic ps - just in case */ |
| ieee80211_enable_dyn_ps(wl->vif); |
| |
| /* revert back to minimum rates for the current band */ |
| wl1271_set_band_rate(wl); |
| wl->basic_rate = wl1271_tx_min_rate_get(wl); |
| ret = wl1271_acx_sta_rate_policies(wl); |
| if (ret < 0) |
| goto out; |
| |
| /* disable connection monitor features */ |
| ret = wl1271_acx_conn_monit_params(wl, false); |
| |
| /* Disable the keep-alive feature */ |
| ret = wl1271_acx_keep_alive_mode(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| /* restore the bssid filter and go to dummy bssid */ |
| wl1271_unjoin(wl); |
| wl1271_dummy_join(wl); |
| } |
| } |
| |
| ret = wl1271_bss_erp_info_changed(wl, bss_conf, changed); |
| if (ret < 0) |
| goto out; |
| |
| rcu_read_lock(); |
| sta = ieee80211_find_sta(vif, bss_conf->bssid); |
| if (sta) { |
| /* handle new association with HT and HT information change */ |
| if ((changed & BSS_CHANGED_HT) && |
| (bss_conf->channel_type != NL80211_CHAN_NO_HT)) { |
| ret = wl1271_acx_set_ht_capabilities(wl, &sta->ht_cap, |
| true); |
| if (ret < 0) { |
| wl1271_warning("Set ht cap true failed %d", |
| ret); |
| rcu_read_unlock(); |
| goto out; |
| } |
| ret = wl1271_acx_set_ht_information(wl, |
| bss_conf->ht_operation_mode); |
| if (ret < 0) { |
| wl1271_warning("Set ht information failed %d", |
| ret); |
| rcu_read_unlock(); |
| goto out; |
| } |
| } |
| /* handle new association without HT and disassociation */ |
| else if (changed & BSS_CHANGED_ASSOC) { |
| ret = wl1271_acx_set_ht_capabilities(wl, &sta->ht_cap, |
| false); |
| if (ret < 0) { |
| wl1271_warning("Set ht cap false failed %d", |
| ret); |
| rcu_read_unlock(); |
| goto out; |
| } |
| } |
| } |
| rcu_read_unlock(); |
| |
| if (changed & BSS_CHANGED_ARP_FILTER) { |
| __be32 addr = bss_conf->arp_addr_list[0]; |
| WARN_ON(wl->bss_type != BSS_TYPE_STA_BSS); |
| |
| if (bss_conf->arp_addr_cnt == 1 && |
| bss_conf->arp_filter_enabled) { |
| /* |
| * The template should have been configured only upon |
| * association. however, it seems that the correct ip |
| * isn't being set (when sending), so we have to |
| * reconfigure the template upon every ip change. |
| */ |
| ret = wl1271_cmd_build_arp_rsp(wl, addr); |
| if (ret < 0) { |
| wl1271_warning("build arp rsp failed: %d", ret); |
| goto out; |
| } |
| |
| ret = wl1271_acx_arp_ip_filter(wl, |
| (ACX_ARP_FILTER_ARP_FILTERING | |
| ACX_ARP_FILTER_AUTO_ARP), |
| addr); |
| } else |
| ret = wl1271_acx_arp_ip_filter(wl, 0, addr); |
| |
| if (ret < 0) |
| goto out; |
| } |
| |
| if (do_join) { |
| ret = wl1271_join(wl, set_assoc); |
| if (ret < 0) { |
| wl1271_warning("cmd join failed %d", ret); |
| goto out; |
| } |
| } |
| |
| out: |
| return; |
| } |
| |
| static void wl1271_op_bss_info_changed(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *bss_conf, |
| u32 changed) |
| { |
| struct wl1271 *wl = hw->priv; |
| bool is_ap = (wl->bss_type == BSS_TYPE_AP_BSS); |
| int ret; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 bss info changed 0x%x", |
| (int)changed); |
| |
| mutex_lock(&wl->mutex); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) |
| goto out; |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| if (is_ap) |
| wl1271_bss_info_changed_ap(wl, vif, bss_conf, changed); |
| else |
| wl1271_bss_info_changed_sta(wl, vif, bss_conf, changed); |
| |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| } |
| |
| static int wl1271_op_conf_tx(struct ieee80211_hw *hw, u16 queue, |
| const struct ieee80211_tx_queue_params *params) |
| { |
| struct wl1271 *wl = hw->priv; |
| u8 ps_scheme; |
| int ret = 0; |
| |
| mutex_lock(&wl->mutex); |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 conf tx %d", queue); |
| |
| if (params->uapsd) |
| ps_scheme = CONF_PS_SCHEME_UPSD_TRIGGER; |
| else |
| ps_scheme = CONF_PS_SCHEME_LEGACY; |
| |
| if (wl->state == WL1271_STATE_OFF) { |
| /* |
| * If the state is off, the parameters will be recorded and |
| * configured on init. This happens in AP-mode. |
| */ |
| struct conf_tx_ac_category *conf_ac = |
| &wl->conf.tx.ac_conf[wl1271_tx_get_queue(queue)]; |
| struct conf_tx_tid *conf_tid = |
| &wl->conf.tx.tid_conf[wl1271_tx_get_queue(queue)]; |
| |
| conf_ac->ac = wl1271_tx_get_queue(queue); |
| conf_ac->cw_min = (u8)params->cw_min; |
| conf_ac->cw_max = params->cw_max; |
| conf_ac->aifsn = params->aifs; |
| conf_ac->tx_op_limit = params->txop << 5; |
| |
| conf_tid->queue_id = wl1271_tx_get_queue(queue); |
| conf_tid->channel_type = CONF_CHANNEL_TYPE_EDCF; |
| conf_tid->tsid = wl1271_tx_get_queue(queue); |
| conf_tid->ps_scheme = ps_scheme; |
| conf_tid->ack_policy = CONF_ACK_POLICY_LEGACY; |
| conf_tid->apsd_conf[0] = 0; |
| conf_tid->apsd_conf[1] = 0; |
| } else { |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| /* |
| * the txop is confed in units of 32us by the mac80211, |
| * we need us |
| */ |
| ret = wl1271_acx_ac_cfg(wl, wl1271_tx_get_queue(queue), |
| params->cw_min, params->cw_max, |
| params->aifs, params->txop << 5); |
| if (ret < 0) |
| goto out_sleep; |
| |
| ret = wl1271_acx_tid_cfg(wl, wl1271_tx_get_queue(queue), |
| CONF_CHANNEL_TYPE_EDCF, |
| wl1271_tx_get_queue(queue), |
| ps_scheme, CONF_ACK_POLICY_LEGACY, |
| 0, 0); |
| if (ret < 0) |
| goto out_sleep; |
| |
| out_sleep: |
| wl1271_ps_elp_sleep(wl); |
| } |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| |
| return ret; |
| } |
| |
| static u64 wl1271_op_get_tsf(struct ieee80211_hw *hw) |
| { |
| |
| struct wl1271 *wl = hw->priv; |
| u64 mactime = ULLONG_MAX; |
| int ret; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 get tsf"); |
| |
| mutex_lock(&wl->mutex); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) |
| goto out; |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_acx_tsf_info(wl, &mactime); |
| if (ret < 0) |
| goto out_sleep; |
| |
| out_sleep: |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| return mactime; |
| } |
| |
| static int wl1271_op_get_survey(struct ieee80211_hw *hw, int idx, |
| struct survey_info *survey) |
| { |
| struct wl1271 *wl = hw->priv; |
| struct ieee80211_conf *conf = &hw->conf; |
| |
| if (idx != 0) |
| return -ENOENT; |
| |
| survey->channel = conf->channel; |
| survey->filled = SURVEY_INFO_NOISE_DBM; |
| survey->noise = wl->noise; |
| |
| return 0; |
| } |
| |
| static int wl1271_allocate_hlid(struct wl1271 *wl, |
| struct ieee80211_sta *sta, |
| u8 *hlid) |
| { |
| struct wl1271_station *wl_sta; |
| int id; |
| |
| id = find_first_zero_bit(wl->ap_hlid_map, AP_MAX_STATIONS); |
| if (id >= AP_MAX_STATIONS) { |
| wl1271_warning("could not allocate HLID - too much stations"); |
| return -EBUSY; |
| } |
| |
| wl_sta = (struct wl1271_station *)sta->drv_priv; |
| |
| __set_bit(id, wl->ap_hlid_map); |
| wl_sta->hlid = WL1271_AP_STA_HLID_START + id; |
| *hlid = wl_sta->hlid; |
| return 0; |
| } |
| |
| static void wl1271_free_hlid(struct wl1271 *wl, u8 hlid) |
| { |
| int id = hlid - WL1271_AP_STA_HLID_START; |
| |
| __clear_bit(id, wl->ap_hlid_map); |
| } |
| |
| static int wl1271_op_sta_add(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta) |
| { |
| struct wl1271 *wl = hw->priv; |
| int ret = 0; |
| u8 hlid; |
| |
| mutex_lock(&wl->mutex); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) |
| goto out; |
| |
| if (wl->bss_type != BSS_TYPE_AP_BSS) |
| goto out; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 add sta %d", (int)sta->aid); |
| |
| ret = wl1271_allocate_hlid(wl, sta, &hlid); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_cmd_add_sta(wl, sta, hlid); |
| if (ret < 0) |
| goto out_sleep; |
| |
| out_sleep: |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| return ret; |
| } |
| |
| static int wl1271_op_sta_remove(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta) |
| { |
| struct wl1271 *wl = hw->priv; |
| struct wl1271_station *wl_sta; |
| int ret = 0, id; |
| |
| mutex_lock(&wl->mutex); |
| |
| if (unlikely(wl->state == WL1271_STATE_OFF)) |
| goto out; |
| |
| if (wl->bss_type != BSS_TYPE_AP_BSS) |
| goto out; |
| |
| wl1271_debug(DEBUG_MAC80211, "mac80211 remove sta %d", (int)sta->aid); |
| |
| wl_sta = (struct wl1271_station *)sta->drv_priv; |
| id = wl_sta->hlid - WL1271_AP_STA_HLID_START; |
| if (WARN_ON(!test_bit(id, wl->ap_hlid_map))) |
| goto out; |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| ret = wl1271_cmd_remove_sta(wl, wl_sta->hlid); |
| if (ret < 0) |
| goto out_sleep; |
| |
| wl1271_free_hlid(wl, wl_sta->hlid); |
| |
| out_sleep: |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| return ret; |
| } |
| |
| /* can't be const, mac80211 writes to this */ |
| static struct ieee80211_rate wl1271_rates[] = { |
| { .bitrate = 10, |
| .hw_value = CONF_HW_BIT_RATE_1MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_1MBPS, }, |
| { .bitrate = 20, |
| .hw_value = CONF_HW_BIT_RATE_2MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_2MBPS, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| { .bitrate = 55, |
| .hw_value = CONF_HW_BIT_RATE_5_5MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_5_5MBPS, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| { .bitrate = 110, |
| .hw_value = CONF_HW_BIT_RATE_11MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_11MBPS, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| { .bitrate = 60, |
| .hw_value = CONF_HW_BIT_RATE_6MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_6MBPS, }, |
| { .bitrate = 90, |
| .hw_value = CONF_HW_BIT_RATE_9MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_9MBPS, }, |
| { .bitrate = 120, |
| .hw_value = CONF_HW_BIT_RATE_12MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_12MBPS, }, |
| { .bitrate = 180, |
| .hw_value = CONF_HW_BIT_RATE_18MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_18MBPS, }, |
| { .bitrate = 240, |
| .hw_value = CONF_HW_BIT_RATE_24MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_24MBPS, }, |
| { .bitrate = 360, |
| .hw_value = CONF_HW_BIT_RATE_36MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_36MBPS, }, |
| { .bitrate = 480, |
| .hw_value = CONF_HW_BIT_RATE_48MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_48MBPS, }, |
| { .bitrate = 540, |
| .hw_value = CONF_HW_BIT_RATE_54MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_54MBPS, }, |
| }; |
| |
| /* can't be const, mac80211 writes to this */ |
| static struct ieee80211_channel wl1271_channels[] = { |
| { .hw_value = 1, .center_freq = 2412, .max_power = 25 }, |
| { .hw_value = 2, .center_freq = 2417, .max_power = 25 }, |
| { .hw_value = 3, .center_freq = 2422, .max_power = 25 }, |
| { .hw_value = 4, .center_freq = 2427, .max_power = 25 }, |
| { .hw_value = 5, .center_freq = 2432, .max_power = 25 }, |
| { .hw_value = 6, .center_freq = 2437, .max_power = 25 }, |
| { .hw_value = 7, .center_freq = 2442, .max_power = 25 }, |
| { .hw_value = 8, .center_freq = 2447, .max_power = 25 }, |
| { .hw_value = 9, .center_freq = 2452, .max_power = 25 }, |
| { .hw_value = 10, .center_freq = 2457, .max_power = 25 }, |
| { .hw_value = 11, .center_freq = 2462, .max_power = 25 }, |
| { .hw_value = 12, .center_freq = 2467, .max_power = 25 }, |
| { .hw_value = 13, .center_freq = 2472, .max_power = 25 }, |
| { .hw_value = 14, .center_freq = 2484, .max_power = 25 }, |
| }; |
| |
| /* mapping to indexes for wl1271_rates */ |
| static const u8 wl1271_rate_to_idx_2ghz[] = { |
| /* MCS rates are used only with 11n */ |
| 7, /* CONF_HW_RXTX_RATE_MCS7 */ |
| 6, /* CONF_HW_RXTX_RATE_MCS6 */ |
| 5, /* CONF_HW_RXTX_RATE_MCS5 */ |
| 4, /* CONF_HW_RXTX_RATE_MCS4 */ |
| 3, /* CONF_HW_RXTX_RATE_MCS3 */ |
| 2, /* CONF_HW_RXTX_RATE_MCS2 */ |
| 1, /* CONF_HW_RXTX_RATE_MCS1 */ |
| 0, /* CONF_HW_RXTX_RATE_MCS0 */ |
| |
| 11, /* CONF_HW_RXTX_RATE_54 */ |
| 10, /* CONF_HW_RXTX_RATE_48 */ |
| 9, /* CONF_HW_RXTX_RATE_36 */ |
| 8, /* CONF_HW_RXTX_RATE_24 */ |
| |
| /* TI-specific rate */ |
| CONF_HW_RXTX_RATE_UNSUPPORTED, /* CONF_HW_RXTX_RATE_22 */ |
| |
| 7, /* CONF_HW_RXTX_RATE_18 */ |
| 6, /* CONF_HW_RXTX_RATE_12 */ |
| 3, /* CONF_HW_RXTX_RATE_11 */ |
| 5, /* CONF_HW_RXTX_RATE_9 */ |
| 4, /* CONF_HW_RXTX_RATE_6 */ |
| 2, /* CONF_HW_RXTX_RATE_5_5 */ |
| 1, /* CONF_HW_RXTX_RATE_2 */ |
| 0 /* CONF_HW_RXTX_RATE_1 */ |
| }; |
| |
| /* 11n STA capabilities */ |
| #define HW_RX_HIGHEST_RATE 72 |
| |
| #ifdef CONFIG_WL12XX_HT |
| #define WL12XX_HT_CAP { \ |
| .cap = IEEE80211_HT_CAP_GRN_FLD | IEEE80211_HT_CAP_SGI_20, \ |
| .ht_supported = true, \ |
| .ampdu_factor = IEEE80211_HT_MAX_AMPDU_8K, \ |
| .ampdu_density = IEEE80211_HT_MPDU_DENSITY_8, \ |
| .mcs = { \ |
| .rx_mask = { 0xff, 0, 0, 0, 0, 0, 0, 0, 0, 0, }, \ |
| .rx_highest = cpu_to_le16(HW_RX_HIGHEST_RATE), \ |
| .tx_params = IEEE80211_HT_MCS_TX_DEFINED, \ |
| }, \ |
| } |
| #else |
| #define WL12XX_HT_CAP { \ |
| .ht_supported = false, \ |
| } |
| #endif |
| |
| /* can't be const, mac80211 writes to this */ |
| static struct ieee80211_supported_band wl1271_band_2ghz = { |
| .channels = wl1271_channels, |
| .n_channels = ARRAY_SIZE(wl1271_channels), |
| .bitrates = wl1271_rates, |
| .n_bitrates = ARRAY_SIZE(wl1271_rates), |
| .ht_cap = WL12XX_HT_CAP, |
| }; |
| |
| /* 5 GHz data rates for WL1273 */ |
| static struct ieee80211_rate wl1271_rates_5ghz[] = { |
| { .bitrate = 60, |
| .hw_value = CONF_HW_BIT_RATE_6MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_6MBPS, }, |
| { .bitrate = 90, |
| .hw_value = CONF_HW_BIT_RATE_9MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_9MBPS, }, |
| { .bitrate = 120, |
| .hw_value = CONF_HW_BIT_RATE_12MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_12MBPS, }, |
| { .bitrate = 180, |
| .hw_value = CONF_HW_BIT_RATE_18MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_18MBPS, }, |
| { .bitrate = 240, |
| .hw_value = CONF_HW_BIT_RATE_24MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_24MBPS, }, |
| { .bitrate = 360, |
| .hw_value = CONF_HW_BIT_RATE_36MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_36MBPS, }, |
| { .bitrate = 480, |
| .hw_value = CONF_HW_BIT_RATE_48MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_48MBPS, }, |
| { .bitrate = 540, |
| .hw_value = CONF_HW_BIT_RATE_54MBPS, |
| .hw_value_short = CONF_HW_BIT_RATE_54MBPS, }, |
| }; |
| |
| /* 5 GHz band channels for WL1273 */ |
| static struct ieee80211_channel wl1271_channels_5ghz[] = { |
| { .hw_value = 7, .center_freq = 5035}, |
| { .hw_value = 8, .center_freq = 5040}, |
| { .hw_value = 9, .center_freq = 5045}, |
| { .hw_value = 11, .center_freq = 5055}, |
| { .hw_value = 12, .center_freq = 5060}, |
| { .hw_value = 16, .center_freq = 5080}, |
| { .hw_value = 34, .center_freq = 5170}, |
| { .hw_value = 36, .center_freq = 5180}, |
| { .hw_value = 38, .center_freq = 5190}, |
| { .hw_value = 40, .center_freq = 5200}, |
| { .hw_value = 42, .center_freq = 5210}, |
| { .hw_value = 44, .center_freq = 5220}, |
| { .hw_value = 46, .center_freq = 5230}, |
| { .hw_value = 48, .center_freq = 5240}, |
| { .hw_value = 52, .center_freq = 5260}, |
| { .hw_value = 56, .center_freq = 5280}, |
| { .hw_value = 60, .center_freq = 5300}, |
| { .hw_value = 64, .center_freq = 5320}, |
| { .hw_value = 100, .center_freq = 5500}, |
| { .hw_value = 104, .center_freq = 5520}, |
| { .hw_value = 108, .center_freq = 5540}, |
| { .hw_value = 112, .center_freq = 5560}, |
| { .hw_value = 116, .center_freq = 5580}, |
| { .hw_value = 120, .center_freq = 5600}, |
| { .hw_value = 124, .center_freq = 5620}, |
| { .hw_value = 128, .center_freq = 5640}, |
| { .hw_value = 132, .center_freq = 5660}, |
| { .hw_value = 136, .center_freq = 5680}, |
| { .hw_value = 140, .center_freq = 5700}, |
| { .hw_value = 149, .center_freq = 5745}, |
| { .hw_value = 153, .center_freq = 5765}, |
| { .hw_value = 157, .center_freq = 5785}, |
| { .hw_value = 161, .center_freq = 5805}, |
| { .hw_value = 165, .center_freq = 5825}, |
| }; |
| |
| /* mapping to indexes for wl1271_rates_5ghz */ |
| static const u8 wl1271_rate_to_idx_5ghz[] = { |
| /* MCS rates are used only with 11n */ |
| 7, /* CONF_HW_RXTX_RATE_MCS7 */ |
| 6, /* CONF_HW_RXTX_RATE_MCS6 */ |
| 5, /* CONF_HW_RXTX_RATE_MCS5 */ |
| 4, /* CONF_HW_RXTX_RATE_MCS4 */ |
| 3, /* CONF_HW_RXTX_RATE_MCS3 */ |
| 2, /* CONF_HW_RXTX_RATE_MCS2 */ |
| 1, /* CONF_HW_RXTX_RATE_MCS1 */ |
| 0, /* CONF_HW_RXTX_RATE_MCS0 */ |
| |
| 7, /* CONF_HW_RXTX_RATE_54 */ |
| 6, /* CONF_HW_RXTX_RATE_48 */ |
| 5, /* CONF_HW_RXTX_RATE_36 */ |
| 4, /* CONF_HW_RXTX_RATE_24 */ |
| |
| /* TI-specific rate */ |
| CONF_HW_RXTX_RATE_UNSUPPORTED, /* CONF_HW_RXTX_RATE_22 */ |
| |
| 3, /* CONF_HW_RXTX_RATE_18 */ |
| 2, /* CONF_HW_RXTX_RATE_12 */ |
| CONF_HW_RXTX_RATE_UNSUPPORTED, /* CONF_HW_RXTX_RATE_11 */ |
| 1, /* CONF_HW_RXTX_RATE_9 */ |
| 0, /* CONF_HW_RXTX_RATE_6 */ |
| CONF_HW_RXTX_RATE_UNSUPPORTED, /* CONF_HW_RXTX_RATE_5_5 */ |
| CONF_HW_RXTX_RATE_UNSUPPORTED, /* CONF_HW_RXTX_RATE_2 */ |
| CONF_HW_RXTX_RATE_UNSUPPORTED /* CONF_HW_RXTX_RATE_1 */ |
| }; |
| |
| static struct ieee80211_supported_band wl1271_band_5ghz = { |
| .channels = wl1271_channels_5ghz, |
| .n_channels = ARRAY_SIZE(wl1271_channels_5ghz), |
| .bitrates = wl1271_rates_5ghz, |
| .n_bitrates = ARRAY_SIZE(wl1271_rates_5ghz), |
| .ht_cap = WL12XX_HT_CAP, |
| }; |
| |
| static const u8 *wl1271_band_rate_to_idx[] = { |
| [IEEE80211_BAND_2GHZ] = wl1271_rate_to_idx_2ghz, |
| [IEEE80211_BAND_5GHZ] = wl1271_rate_to_idx_5ghz |
| }; |
| |
| static const struct ieee80211_ops wl1271_ops = { |
| .start = wl1271_op_start, |
| .stop = wl1271_op_stop, |
| .add_interface = wl1271_op_add_interface, |
| .remove_interface = wl1271_op_remove_interface, |
| .config = wl1271_op_config, |
| .prepare_multicast = wl1271_op_prepare_multicast, |
| .configure_filter = wl1271_op_configure_filter, |
| .tx = wl1271_op_tx, |
| .set_key = wl1271_op_set_key, |
| .hw_scan = wl1271_op_hw_scan, |
| .bss_info_changed = wl1271_op_bss_info_changed, |
| .set_frag_threshold = wl1271_op_set_frag_threshold, |
| .set_rts_threshold = wl1271_op_set_rts_threshold, |
| .conf_tx = wl1271_op_conf_tx, |
| .get_tsf = wl1271_op_get_tsf, |
| .get_survey = wl1271_op_get_survey, |
| .sta_add = wl1271_op_sta_add, |
| .sta_remove = wl1271_op_sta_remove, |
| CFG80211_TESTMODE_CMD(wl1271_tm_cmd) |
| }; |
| |
| |
| u8 wl1271_rate_to_idx(int rate, enum ieee80211_band band) |
| { |
| u8 idx; |
| |
| BUG_ON(band >= sizeof(wl1271_band_rate_to_idx)/sizeof(u8 *)); |
| |
| if (unlikely(rate >= CONF_HW_RXTX_RATE_MAX)) { |
| wl1271_error("Illegal RX rate from HW: %d", rate); |
| return 0; |
| } |
| |
| idx = wl1271_band_rate_to_idx[band][rate]; |
| if (unlikely(idx == CONF_HW_RXTX_RATE_UNSUPPORTED)) { |
| wl1271_error("Unsupported RX rate from HW: %d", rate); |
| return 0; |
| } |
| |
| return idx; |
| } |
| |
| static ssize_t wl1271_sysfs_show_bt_coex_state(struct device *dev, |
| struct device_attribute *attr, |
| char *buf) |
| { |
| struct wl1271 *wl = dev_get_drvdata(dev); |
| ssize_t len; |
| |
| len = PAGE_SIZE; |
| |
| mutex_lock(&wl->mutex); |
| len = snprintf(buf, len, "%d\n\n0 - off\n1 - on\n", |
| wl->sg_enabled); |
| mutex_unlock(&wl->mutex); |
| |
| return len; |
| |
| } |
| |
| static ssize_t wl1271_sysfs_store_bt_coex_state(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct wl1271 *wl = dev_get_drvdata(dev); |
| unsigned long res; |
| int ret; |
| |
| ret = strict_strtoul(buf, 10, &res); |
| |
| if (ret < 0) { |
| wl1271_warning("incorrect value written to bt_coex_mode"); |
| return count; |
| } |
| |
| mutex_lock(&wl->mutex); |
| |
| res = !!res; |
| |
| if (res == wl->sg_enabled) |
| goto out; |
| |
| wl->sg_enabled = res; |
| |
| if (wl->state == WL1271_STATE_OFF) |
| goto out; |
| |
| ret = wl1271_ps_elp_wakeup(wl, false); |
| if (ret < 0) |
| goto out; |
| |
| wl1271_acx_sg_enable(wl, wl->sg_enabled); |
| wl1271_ps_elp_sleep(wl); |
| |
| out: |
| mutex_unlock(&wl->mutex); |
| return count; |
| } |
| |
| static DEVICE_ATTR(bt_coex_state, S_IRUGO | S_IWUSR, |
| wl1271_sysfs_show_bt_coex_state, |
| wl1271_sysfs_store_bt_coex_state); |
| |
| static ssize_t wl1271_sysfs_show_hw_pg_ver(struct device *dev, |
| struct device_attribute *attr, |
| char *buf) |
| { |
| struct wl1271 *wl = dev_get_drvdata(dev); |
| ssize_t len; |
| |
| len = PAGE_SIZE; |
| |
| mutex_lock(&wl->mutex); |
| if (wl->hw_pg_ver >= 0) |
| len = snprintf(buf, len, "%d\n", wl->hw_pg_ver); |
| else |
| len = snprintf(buf, len, "n/a\n"); |
| mutex_unlock(&wl->mutex); |
| |
| return len; |
| } |
| |
| static DEVICE_ATTR(hw_pg_ver, S_IRUGO | S_IWUSR, |
| wl1271_sysfs_show_hw_pg_ver, NULL); |
| |
| int wl1271_register_hw(struct wl1271 *wl) |
| { |
| int ret; |
| |
| if (wl->mac80211_registered) |
| return 0; |
| |
| ret = wl1271_fetch_nvs(wl); |
| if (ret == 0) { |
| u8 *nvs_ptr = (u8 *)wl->nvs->nvs; |
| |
| wl->mac_addr[0] = nvs_ptr[11]; |
| wl->mac_addr[1] = nvs_ptr[10]; |
| wl->mac_addr[2] = nvs_ptr[6]; |
| wl->mac_addr[3] = nvs_ptr[5]; |
| wl->mac_addr[4] = nvs_ptr[4]; |
| wl->mac_addr[5] = nvs_ptr[3]; |
| } |
| |
| SET_IEEE80211_PERM_ADDR(wl->hw, wl->mac_addr); |
| |
| ret = ieee80211_register_hw(wl->hw); |
| if (ret < 0) { |
| wl1271_error("unable to register mac80211 hw: %d", ret); |
| return ret; |
| } |
| |
| wl->mac80211_registered = true; |
| |
| wl1271_debugfs_init(wl); |
| |
| register_netdevice_notifier(&wl1271_dev_notifier); |
| |
| wl1271_notice("loaded"); |
| |
| return 0; |
| } |
| EXPORT_SYMBOL_GPL(wl1271_register_hw); |
| |
| void wl1271_unregister_hw(struct wl1271 *wl) |
| { |
| if (wl->state == WL1271_STATE_PLT) |
| __wl1271_plt_stop(wl); |
| |
| unregister_netdevice_notifier(&wl1271_dev_notifier); |
| ieee80211_unregister_hw(wl->hw); |
| wl->mac80211_registered = false; |
| |
| } |
| EXPORT_SYMBOL_GPL(wl1271_unregister_hw); |
| |
| int wl1271_init_ieee80211(struct wl1271 *wl) |
| { |
| static const u32 cipher_suites[] = { |
| WLAN_CIPHER_SUITE_WEP40, |
| WLAN_CIPHER_SUITE_WEP104, |
| WLAN_CIPHER_SUITE_TKIP, |
| WLAN_CIPHER_SUITE_CCMP, |
| WL1271_CIPHER_SUITE_GEM, |
| }; |
| |
| /* The tx descriptor buffer and the TKIP space. */ |
| wl->hw->extra_tx_headroom = WL1271_TKIP_IV_SPACE + |
| sizeof(struct wl1271_tx_hw_descr); |
| |
| /* unit us */ |
| /* FIXME: find a proper value */ |
| wl->hw->channel_change_time = 10000; |
| wl->hw->max_listen_interval = wl->conf.conn.max_listen_interval; |
| |
| wl->hw->flags = IEEE80211_HW_SIGNAL_DBM | |
| IEEE80211_HW_BEACON_FILTER | |
| IEEE80211_HW_SUPPORTS_PS | |
| IEEE80211_HW_SUPPORTS_UAPSD | |
| IEEE80211_HW_HAS_RATE_CONTROL | |
| IEEE80211_HW_CONNECTION_MONITOR | |
| IEEE80211_HW_SUPPORTS_CQM_RSSI; |
| |
| wl->hw->wiphy->cipher_suites = cipher_suites; |
| wl->hw->wiphy->n_cipher_suites = ARRAY_SIZE(cipher_suites); |
| |
| wl->hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) | |
| BIT(NL80211_IFTYPE_ADHOC) | BIT(NL80211_IFTYPE_AP); |
| wl->hw->wiphy->max_scan_ssids = 1; |
| /* |
| * Maximum length of elements in scanning probe request templates |
| * should be the maximum length possible for a template, without |
| * the IEEE80211 header of the template |
| */ |
| wl->hw->wiphy->max_scan_ie_len = WL1271_CMD_TEMPL_MAX_SIZE - |
| sizeof(struct ieee80211_header); |
| |
| /* |
| * We keep local copies of the band structs because we need to |
| * modify them on a per-device basis. |
| */ |
| memcpy(&wl->bands[IEEE80211_BAND_2GHZ], &wl1271_band_2ghz, |
| sizeof(wl1271_band_2ghz)); |
| memcpy(&wl->bands[IEEE80211_BAND_5GHZ], &wl1271_band_5ghz, |
| sizeof(wl1271_band_5ghz)); |
| |
| wl->hw->wiphy->bands[IEEE80211_BAND_2GHZ] = |
| &wl->bands[IEEE80211_BAND_2GHZ]; |
| wl->hw->wiphy->bands[IEEE80211_BAND_5GHZ] = |
| &wl->bands[IEEE80211_BAND_5GHZ]; |
| |
| wl->hw->queues = 4; |
| wl->hw->max_rates = 1; |
| |
| wl->hw->wiphy->reg_notifier = wl1271_reg_notify; |
| |
| SET_IEEE80211_DEV(wl->hw, wl1271_wl_to_dev(wl)); |
| |
| wl->hw->sta_data_size = sizeof(struct wl1271_station); |
| |
| wl->hw->max_rx_aggregation_subframes = 8; |
| |
| return 0; |
| } |
| EXPORT_SYMBOL_GPL(wl1271_init_ieee80211); |
| |
| #define WL1271_DEFAULT_CHANNEL 0 |
| |
| struct ieee80211_hw *wl1271_alloc_hw(void) |
| { |
| struct ieee80211_hw *hw; |
| struct platform_device *plat_dev = NULL; |
| struct wl1271 *wl; |
| int i, ret; |
| unsigned int order; |
| |
| hw = ieee80211_alloc_hw(sizeof(*wl), &wl1271_ops); |
| if (!hw) { |
| wl1271_error("could not alloc ieee80211_hw"); |
| ret = -ENOMEM; |
| goto err_hw_alloc; |
| } |
| |
| plat_dev = kmemdup(&wl1271_device, sizeof(wl1271_device), GFP_KERNEL); |
| if (!plat_dev) { |
| wl1271_error("could not allocate platform_device"); |
| ret = -ENOMEM; |
| goto err_plat_alloc; |
| } |
| |
| wl = hw->priv; |
| memset(wl, 0, sizeof(*wl)); |
| |
| INIT_LIST_HEAD(&wl->list); |
| |
| wl->hw = hw; |
| wl->plat_dev = plat_dev; |
| |
| for (i = 0; i < NUM_TX_QUEUES; i++) |
| skb_queue_head_init(&wl->tx_queue[i]); |
| |
| INIT_DELAYED_WORK(&wl->elp_work, wl1271_elp_work); |
| INIT_DELAYED_WORK(&wl->pspoll_work, wl1271_pspoll_work); |
| INIT_WORK(&wl->irq_work, wl1271_irq_work); |
| INIT_WORK(&wl->tx_work, wl1271_tx_work); |
| INIT_WORK(&wl->recovery_work, wl1271_recovery_work); |
| INIT_DELAYED_WORK(&wl->scan_complete_work, wl1271_scan_complete_work); |
| wl->channel = WL1271_DEFAULT_CHANNEL; |
| wl->beacon_int = WL1271_DEFAULT_BEACON_INT; |
| wl->default_key = 0; |
| wl->rx_counter = 0; |
| wl->rx_config = WL1271_DEFAULT_STA_RX_CONFIG; |
| wl->rx_filter = WL1271_DEFAULT_STA_RX_FILTER; |
| wl->psm_entry_retry = 0; |
| wl->power_level = WL1271_DEFAULT_POWER_LEVEL; |
| wl->basic_rate_set = CONF_TX_RATE_MASK_BASIC; |
| wl->basic_rate = CONF_TX_RATE_MASK_BASIC; |
| wl->rate_set = CONF_TX_RATE_MASK_BASIC; |
| wl->sta_rate_set = 0; |
| wl->band = IEEE80211_BAND_2GHZ; |
| wl->vif = NULL; |
| wl->flags = 0; |
| wl->sg_enabled = true; |
| wl->hw_pg_ver = -1; |
| wl->bss_type = MAX_BSS_TYPE; |
| wl->set_bss_type = MAX_BSS_TYPE; |
| wl->fw_bss_type = MAX_BSS_TYPE; |
| |
| memset(wl->tx_frames_map, 0, sizeof(wl->tx_frames_map)); |
| for (i = 0; i < ACX_TX_DESCRIPTORS; i++) |
| wl->tx_frames[i] = NULL; |
| |
| spin_lock_init(&wl->wl_lock); |
| |
| wl->state = WL1271_STATE_OFF; |
| mutex_init(&wl->mutex); |
| |
| /* Apply default driver configuration. */ |
| wl1271_conf_init(wl); |
| |
| order = get_order(WL1271_AGGR_BUFFER_SIZE); |
| wl->aggr_buf = (u8 *)__get_free_pages(GFP_KERNEL, order); |
| if (!wl->aggr_buf) { |
| ret = -ENOMEM; |
| goto err_hw; |
| } |
| |
| /* Register platform device */ |
| ret = platform_device_register(wl->plat_dev); |
| if (ret) { |
| wl1271_error("couldn't register platform device"); |
| goto err_aggr; |
| } |
| dev_set_drvdata(&wl->plat_dev->dev, wl); |
| |
| /* Create sysfs file to control bt coex state */ |
| ret = device_create_file(&wl->plat_dev->dev, &dev_attr_bt_coex_state); |
| if (ret < 0) { |
| wl1271_error("failed to create sysfs file bt_coex_state"); |
| goto err_platform; |
| } |
| |
| /* Create sysfs file to get HW PG version */ |
| ret = device_create_file(&wl->plat_dev->dev, &dev_attr_hw_pg_ver); |
| if (ret < 0) { |
| wl1271_error("failed to create sysfs file hw_pg_ver"); |
| goto err_bt_coex_state; |
| } |
| |
| return hw; |
| |
| err_bt_coex_state: |
| device_remove_file(&wl->plat_dev->dev, &dev_attr_bt_coex_state); |
| |
| err_platform: |
| platform_device_unregister(wl->plat_dev); |
| |
| err_aggr: |
| free_pages((unsigned long)wl->aggr_buf, order); |
| |
| err_hw: |
| wl1271_debugfs_exit(wl); |
| kfree(plat_dev); |
| |
| err_plat_alloc: |
| ieee80211_free_hw(hw); |
| |
| err_hw_alloc: |
| |
| return ERR_PTR(ret); |
| } |
| EXPORT_SYMBOL_GPL(wl1271_alloc_hw); |
| |
| int wl1271_free_hw(struct wl1271 *wl) |
| { |
| platform_device_unregister(wl->plat_dev); |
| free_pages((unsigned long)wl->aggr_buf, |
| get_order(WL1271_AGGR_BUFFER_SIZE)); |
| kfree(wl->plat_dev); |
| |
| wl1271_debugfs_exit(wl); |
| |
| vfree(wl->fw); |
| wl->fw = NULL; |
| kfree(wl->nvs); |
| wl->nvs = NULL; |
| |
| kfree(wl->fw_status); |
| kfree(wl->tx_res_if); |
| |
| ieee80211_free_hw(wl->hw); |
| |
| return 0; |
| } |
| EXPORT_SYMBOL_GPL(wl1271_free_hw); |
| |
| u32 wl12xx_debug_level = DEBUG_NONE; |
| EXPORT_SYMBOL_GPL(wl12xx_debug_level); |
| module_param_named(debug_level, wl12xx_debug_level, uint, S_IRUSR | S_IWUSR); |
| MODULE_PARM_DESC(debug_level, "wl12xx debugging level"); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("Luciano Coelho <luciano.coelho@nokia.com>"); |
| MODULE_AUTHOR("Juuso Oikarinen <juuso.oikarinen@nokia.com>"); |