blob: f33b997f2b61c514a7f7d7017843fbbbe766472c [file] [log] [blame]
/*
* drivers/net/ethernet/mellanox/mlxsw/port.h
* Copyright (c) 2015 Mellanox Technologies. All rights reserved.
* Copyright (c) 2015 Elad Raz <eladr@mellanox.com>
* Copyright (c) 2015 Jiri Pirko <jiri@mellanox.com>
* Copyright (c) 2015 Ido Schimmel <idosch@mellanox.com>
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the names of the copyright holders nor the names of its
* contributors may be used to endorse or promote products derived from
* this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef _MLXSW_PORT_H
#define _MLXSW_PORT_H
#include <linux/types.h>
#define MLXSW_PORT_MAX_MTU 10000
#define MLXSW_PORT_DEFAULT_VID 1
#define MLXSW_PORT_SWID_DISABLED_PORT 255
#define MLXSW_PORT_SWID_ALL_SWIDS 254
#define MLXSW_PORT_SWID_TYPE_ETH 2
#define MLXSW_PORT_MID 0xd000
#define MLXSW_PORT_MAX_PHY_PORTS 0x40
#define MLXSW_PORT_MAX_PORTS (MLXSW_PORT_MAX_PHY_PORTS + 1)
#define MLXSW_PORT_DEVID_BITS_OFFSET 10
#define MLXSW_PORT_PHY_BITS_OFFSET 4
#define MLXSW_PORT_PHY_BITS_MASK (MLXSW_PORT_MAX_PHY_PORTS - 1)
#define MLXSW_PORT_CPU_PORT 0x0
#define MLXSW_PORT_DONT_CARE (MLXSW_PORT_MAX_PORTS)
#define MLXSW_PORT_MODULE_MAX_WIDTH 4
enum mlxsw_port_admin_status {
MLXSW_PORT_ADMIN_STATUS_UP = 1,
MLXSW_PORT_ADMIN_STATUS_DOWN = 2,
MLXSW_PORT_ADMIN_STATUS_UP_ONCE = 3,
MLXSW_PORT_ADMIN_STATUS_DISABLED = 4,
};
enum mlxsw_reg_pude_oper_status {
MLXSW_PORT_OPER_STATUS_UP = 1,
MLXSW_PORT_OPER_STATUS_DOWN = 2,
MLXSW_PORT_OPER_STATUS_FAILURE = 4, /* Can be set to up again. */
};
#endif /* _MLXSW_PORT_H */