| /***************************************************************************/ |
| |
| /* |
| * m5307.c -- platform support for ColdFire 5307 based boards |
| * |
| * Copyright (C) 1999-2002, Greg Ungerer (gerg@snapgear.com) |
| * Copyright (C) 2000, Lineo (www.lineo.com) |
| */ |
| |
| /***************************************************************************/ |
| |
| #include <linux/kernel.h> |
| #include <linux/param.h> |
| #include <linux/init.h> |
| #include <linux/io.h> |
| #include <asm/machdep.h> |
| #include <asm/coldfire.h> |
| #include <asm/mcfsim.h> |
| #include <asm/mcfwdebug.h> |
| #include <asm/mcfclk.h> |
| |
| /***************************************************************************/ |
| |
| /* |
| * Some platforms need software versions of the GPIO data registers. |
| */ |
| unsigned short ppdata; |
| unsigned char ledbank = 0xff; |
| |
| /***************************************************************************/ |
| |
| DEFINE_CLK(pll, "pll.0", MCF_CLK); |
| DEFINE_CLK(sys, "sys.0", MCF_BUSCLK); |
| DEFINE_CLK(mcftmr0, "mcftmr.0", MCF_BUSCLK); |
| DEFINE_CLK(mcftmr1, "mcftmr.1", MCF_BUSCLK); |
| DEFINE_CLK(mcfuart0, "mcfuart.0", MCF_BUSCLK); |
| DEFINE_CLK(mcfuart1, "mcfuart.1", MCF_BUSCLK); |
| DEFINE_CLK(mcfi2c0, "imx1-i2c.0", MCF_BUSCLK); |
| |
| struct clk *mcf_clks[] = { |
| &clk_pll, |
| &clk_sys, |
| &clk_mcftmr0, |
| &clk_mcftmr1, |
| &clk_mcfuart0, |
| &clk_mcfuart1, |
| &clk_mcfi2c0, |
| NULL |
| }; |
| |
| /***************************************************************************/ |
| |
| static void __init m5307_i2c_init(void) |
| { |
| #if IS_ENABLED(CONFIG_I2C_IMX) |
| writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL5 | MCFSIM_ICR_PRI0, |
| MCFSIM_I2CICR); |
| mcf_mapirq2imr(MCF_IRQ_I2C0, MCFINTC_I2C); |
| #endif /* IS_ENABLED(CONFIG_I2C_IMX) */ |
| } |
| |
| /***************************************************************************/ |
| |
| void __init config_BSP(char *commandp, int size) |
| { |
| #if defined(CONFIG_NETtel) || \ |
| defined(CONFIG_SECUREEDGEMP3) || defined(CONFIG_CLEOPATRA) |
| /* Copy command line from FLASH to local buffer... */ |
| memcpy(commandp, (char *) 0xf0004000, size); |
| commandp[size-1] = 0; |
| #endif |
| |
| mach_sched_init = hw_timer_init; |
| |
| /* Only support the external interrupts on their primary level */ |
| mcf_mapirq2imr(25, MCFINTC_EINT1); |
| mcf_mapirq2imr(27, MCFINTC_EINT3); |
| mcf_mapirq2imr(29, MCFINTC_EINT5); |
| mcf_mapirq2imr(31, MCFINTC_EINT7); |
| |
| #ifdef CONFIG_BDM_DISABLE |
| /* |
| * Disable the BDM clocking. This also turns off most of the rest of |
| * the BDM device. This is good for EMC reasons. This option is not |
| * incompatible with the memory protection option. |
| */ |
| wdebug(MCFDEBUG_CSR, MCFDEBUG_CSR_PSTCLK); |
| #endif |
| m5307_i2c_init(); |
| } |
| |
| /***************************************************************************/ |