| # SPDX-License-Identifier: GPL-2.0 |
| # |
| # QCOM Soc drivers |
| # |
| menu "Qualcomm SoC drivers" |
| config QCOM_COMMAND_DB |
| bool "Qualcomm Command DB" |
| depends on ARCH_QCOM || COMPILE_TEST |
| depends on OF_RESERVED_MEM |
| help |
| Command DB queries shared memory by key string for shared system |
| resources. Platform drivers that require to set state of a shared |
| resource on a RPM-hardened platform must use this database to get |
| SoC specific identifier and information for the shared resources. |
| |
| config QCOM_MEM_OFFLINE |
| bool "Dynamic Memory Region Offline driver" |
| depends on MEMORY_HOTPLUG |
| help |
| Add support for DDR Self-Refresh power management through the dynamic |
| memory offline framework. This driver interfaces between the memory |
| hotplug subsystem and AOP which hot adds or removes memory blocks and |
| controls the start/stop of self-refresh of these DDR regions. This |
| helps reduce power consumption during idle mode of the system. |
| If unsure, say N |
| |
| config BUG_ON_HW_MEM_ONLINE_FAIL |
| bool "Trigger a BUG when HW memory online fails" |
| depends on QCOM_MEM_OFFLINE |
| help |
| Select this option if kernel should BUG when the hardware |
| onlining of memory hotplug blocks fails. This helps to catch |
| online failures much quicker and avoids the later side effects |
| of such memory online failures. |
| If unsure, say N |
| |
| config QCOM_GENI_SE |
| tristate "QCOM GENI Serial Engine Driver" |
| depends on ARCH_QCOM || COMPILE_TEST |
| help |
| This driver is used to manage Generic Interface (GENI) firmware based |
| Qualcomm Technologies, Inc. Universal Peripheral (QUP) Wrapper. This |
| driver is also used to manage the common aspects of multiple Serial |
| Engines present in the QUP. |
| |
| config OVERRIDE_MEMORY_LIMIT |
| bool "Override memory limit set by the kernel boot parameter" |
| depends on QCOM_MEM_OFFLINE |
| help |
| Override any memory limit set by the kernel boot parameter with |
| limit set by mem-offline dt entry so that memory offline framework |
| can initialize remaining memory with movable pages for memory |
| hot-plugging. |
| If unsure, say N |
| |
| config QCOM_GLINK_SSR |
| tristate "Qualcomm Glink SSR driver" |
| depends on RPMSG |
| depends on QCOM_RPROC_COMMON |
| help |
| Say y here to enable GLINK SSR support. The GLINK SSR driver |
| implements the SSR protocol for notifying the remote processor about |
| neighboring subsystems going up or down. |
| |
| config QCOM_CPUSS_DUMP |
| bool "CPU Subsystem Dumping support" |
| help |
| Add support to dump various hardware entities such as the instruction |
| and data tlb's as well as the unified tlb, which are a part of the |
| cpu subsystem to an allocated buffer. This allows for analysis of the |
| the entities if corruption is suspected. |
| If unsure, say N |
| |
| config QCOM_RUN_QUEUE_STATS |
| bool "Enable collection and exporting of QTI Run Queue stats to userspace" |
| help |
| This option enables the driver to periodically collecting the statistics |
| of kernel run queue information and calculate the load of the system. |
| This information is exported to usespace via sysfs entries and userspace |
| algorithms uses info and decide when to turn on/off the cpu cores. |
| |
| config MSM_QBT_HANDLER |
| bool "Event Handler for QTI Ultrasonic Fingerprint Sensor" |
| help |
| This driver acts as a interrupt handler, where the interrupt is generated |
| by the QTI Ultrasonic Fingerprint Sensor. It queues the events for each |
| interrupt in an event queue and notifies the userspace to read the events |
| from the queue. It also creates an input device to send key events such as |
| KEY_POWER, KEY_HOME. |
| |
| config QCOM_GSBI |
| tristate "QCOM General Serial Bus Interface" |
| depends on ARCH_QCOM |
| select MFD_SYSCON |
| help |
| Say y here to enable GSBI support. The GSBI provides control |
| functions for connecting the underlying serial UART, SPI, and I2C |
| devices to the output pins. |
| |
| config QCOM_IPCC |
| tristate "Qualcomm Technologies, Inc. IPCC driver" |
| depends on MAILBOX |
| help |
| Qualcomm Technologies, Inc. IPCC driver for MSM devices. The drivers |
| acts as an interrupt controller for the clients interested in |
| talking to the IPCC (inbound-communication). On the other hand, the |
| driver also provides a mailbox channel for outbound-communications. |
| Say Y here to compile the driver as a part of kernel or M to compile |
| as a module. |
| |
| config QCOM_LLCC |
| tristate "Qualcomm Technologies, Inc. LLCC driver" |
| depends on ARCH_QCOM |
| help |
| Qualcomm Technologies, Inc. platform specific |
| Last Level Cache Controller(LLCC) driver. This provides interfaces |
| to clients that use the LLCC. Say yes here to enable LLCC slice |
| driver. |
| |
| config QCOM_KONA_LLCC |
| tristate "Qualcomm Technologies, Inc. KONA LLCC driver" |
| depends on QCOM_LLCC |
| help |
| Say yes here to enable the LLCC driver for KONA. This provides |
| data required to configure LLCC so that clients can start using the |
| LLCC slices. |
| |
| config QCOM_LITO_LLCC |
| tristate "Qualcomm Technologies, Inc. LITO LLCC driver" |
| depends on QCOM_LLCC |
| help |
| Say yes here to enable the LLCC driver for LITO. This provides |
| data required to configure LLCC so that clients can start using the |
| LLCC slices. |
| |
| config QCOM_LAGOON_LLCC |
| tristate "Qualcomm Technologies, Inc. LAGOON LLCC driver" |
| depends on QCOM_LLCC |
| help |
| Qualcomm Technologies, Inc. platform specific LLCC driver for LAGOON. |
| Say yes here to enable the LLCC driver for LAGOON. This provides |
| data required to configure LLCC so that clients can start using the |
| LLCC slices. |
| |
| config QCOM_SDM845_LLCC |
| tristate "Qualcomm Technologies, Inc. SDM845 LLCC driver" |
| depends on QCOM_LLCC |
| help |
| Say yes here to enable the LLCC driver for SDM845. This provides |
| data required to configure LLCC so that clients can start using the |
| LLCC slices. |
| |
| config QCOM_LLCC_PERFMON |
| tristate "Qualcomm Technologies, Inc. LLCC Perfmon driver" |
| depends on QCOM_LLCC |
| help |
| This option enables driver for LLCC Performance monitor block. Using |
| this various events in different LLCC sub ports can be monitored. |
| This is used for performance and debug activity and exports sysfs |
| interface. sysfs interface is used to configure and dump the LLCC |
| performance events. |
| |
| config QCOM_MDT_LOADER |
| tristate "Qualcomm Technologies, Inc. Firmware parser for MDT format" |
| select QCOM_SCM |
| help |
| Firmware parser driver parsers the MDT format and loads peripheral |
| images into pre-allocated buffers. It uses the firmware loader |
| framework available for loading firmware. |
| |
| config QPNP_PBS |
| tristate "PBS trigger support for QPNP PMIC" |
| depends on SPMI |
| help |
| This driver supports configuring software PBS trigger event through PBS |
| RAM on Qualcomm Technologies, Inc. QPNP PMICs. This module provides |
| the APIs to the client drivers that wants to send the PBS trigger |
| event to the PBS RAM. |
| |
| config QCOM_PM |
| bool "Qualcomm Power Management" |
| depends on ARCH_QCOM && !ARM64 |
| select ARM_CPU_SUSPEND |
| select QCOM_SCM |
| help |
| QCOM Platform specific power driver to manage cores and L2 low power |
| modes. It interface with various system drivers to put the cores in |
| low power modes. |
| |
| config QCOM_QMI_HELPERS |
| bool "QTI QMI Helpers" |
| depends on QRTR |
| help |
| Helper library for handling QMI encoded messages. QMI encoded |
| messages are used in communication between the majority of QRTR |
| clients and this helpers provide the common functionality needed for |
| doing this from a kernel driver. |
| |
| config QCOM_QMI_RMNET |
| bool "QTI QMI Rmnet Helpers" |
| depends on QCOM_QMI_HELPERS |
| depends on RMNET |
| help |
| Helper for handling interfaces between kernel clients and rmnet |
| driver. It enables the rmnet driver to create/delete DFC/WDA |
| clients and provides the common functionality for data flow control |
| and power save features. |
| |
| config QCOM_QMI_DFC |
| bool "Enable burst mode flow control" |
| depends on QCOM_QMI_RMNET |
| help |
| Say y here to enable support for burst mode data flow control. |
| DFC client provides an interface to the modem dfc service and |
| does burst mode flow control. It enables the flow on receiving flow |
| status indication and disables flows while grant size is reached. |
| If unsure or not use burst mode flow control, say 'N'. |
| |
| source "drivers/soc/qcom/rmnet_ctl/Kconfig" |
| |
| config QCOM_QMI_POWER_COLLAPSE |
| bool "Enable power save features" |
| depends on QCOM_QMI_RMNET |
| help |
| Say y here to enable support for power save features. |
| It provides an interface to offload uplink flow control based on |
| detected flow status. |
| If unsure or not use power save feature, say 'N'. |
| |
| |
| config QCOM_RMTFS_MEM |
| tristate "Qualcomm Remote Filesystem memory driver" |
| depends on ARCH_QCOM |
| select QCOM_SCM |
| help |
| The Qualcomm remote filesystem memory driver is used for allocating |
| and exposing regions of shared memory with remote processors for the |
| purpose of exchanging sector-data between the remote filesystem |
| service and its clients. |
| |
| Say y here if you intend to boot the modem remoteproc. |
| |
| config QCOM_RPMH |
| bool "Qualcomm RPM-Hardened (RPMH) Communication" |
| depends on ARCH_QCOM && ARM64 && OF || COMPILE_TEST |
| help |
| Support for communication with the hardened-RPM blocks in |
| Qualcomm Technologies Inc (QTI) SoCs. RPMH communication uses an |
| internal bus to transmit state requests for shared resources. A set |
| of hardware components aggregate requests for these resources and |
| help apply the aggregated state on the resource. |
| |
| config QCOM_SMEM |
| tristate "Qualcomm Shared Memory Manager (SMEM)" |
| depends on ARCH_QCOM |
| depends on HWSPINLOCK |
| help |
| Say y here to enable support for the Qualcomm Shared Memory Manager. |
| The driver provides an interface to items in a heap shared among all |
| processors in a Qualcomm platform. |
| |
| config QCOM_SMD_RPM |
| tristate "Qualcomm Resource Power Manager (RPM) over SMD" |
| depends on ARCH_QCOM |
| depends on RPMSG && OF |
| help |
| If you say yes to this option, support will be included for the |
| Resource Power Manager system found in the Qualcomm 8974 based |
| devices. |
| |
| This is required to access many regulators, clocks and bus |
| frequencies controlled by the RPM on these devices. |
| |
| Say M here if you want to include support for the Qualcomm RPM as a |
| module. This will build a module called "qcom-smd-rpm". |
| |
| config MSM_SPM |
| bool "Driver support for SPM and AVS wrapper hardware" |
| help |
| Enables the support for SPM and AVS wrapper hardware on MSMs. SPM |
| hardware is used to manage the processor power during sleep. The |
| driver allows configuring SPM to allow different low power modes for |
| both core and L2. |
| |
| config MSM_L2_SPM |
| bool "SPM support for L2 cache" |
| help |
| Enable SPM driver support for L2 cache. Some MSM chipsets allow |
| control of L2 cache low power mode with a Subsystem Power manager. |
| Enabling this driver allows configuring L2 SPM for low power modes |
| on supported chipsets. |
| |
| config QCOM_SCM |
| bool "Secure Channel Manager (SCM) support" |
| default n |
| help |
| Say y here to enable Secure Channel Mananger(SCM) support for SoC. |
| SCM provides communication channel to communicate with secure |
| world(EL2 and EL3) by using smc call. |
| SCM driver provides the support for atomic scm calls also. |
| |
| config QCOM_EARLY_RANDOM |
| bool "Initialize random pool very early" |
| help |
| The standard random pool may not initialize until late in the boot |
| process which means that any calls to get random numbers before then |
| may not be truly random. Select this option to make an early call |
| to get some random data to put in the pool. If unsure, say N. |
| |
| config QCOM_MEMORY_DUMP_V2 |
| bool "QCOM Memory Dump V2 Support" |
| help |
| This enables memory dump feature. It allows various client |
| subsystems to register respective dump regions. At the time |
| of deadlocks or cpu hangs these dump regions are captured to |
| give a snapshot of the system at the time of the crash. |
| |
| config QCOM_SMEM_STATE |
| bool |
| |
| config QCOM_SMP2P |
| tristate "Qualcomm Shared Memory Point to Point support" |
| depends on MAILBOX |
| depends on QCOM_SMEM |
| select QCOM_SMEM_STATE |
| help |
| Say yes here to support the Qualcomm Shared Memory Point to Point |
| protocol. |
| |
| config QCOM_SMSM |
| tristate "Qualcomm Shared Memory State Machine" |
| depends on QCOM_SMEM |
| select QCOM_SMEM_STATE |
| help |
| Say yes here to support the Qualcomm Shared Memory State Machine. |
| The state machine is represented by bits in shared memory. |
| |
| config QCOM_WCNSS_CTRL |
| tristate "Qualcomm WCNSS control driver" |
| depends on ARCH_QCOM |
| depends on RPMSG |
| help |
| Client driver for the WCNSS_CTRL SMD channel, used to download nv |
| firmware to a newly booted WCNSS chip. |
| |
| config SETUP_SSR_NOTIF_TIMEOUTS |
| bool "Set timeouts on SSR sysmon notifications and notifier callbacks" |
| help |
| Setup timers prior to initiating communication between |
| subsystems through sysmon, and prior to sending notifications |
| to drivers in the kernel that have registered callbacks with the |
| subsystem notifier framework for a particular subsystem. This |
| is a debugging feature. |
| |
| config SSR_SYSMON_NOTIF_TIMEOUT |
| depends on SETUP_SSR_NOTIF_TIMEOUTS |
| int "SSR Sysmon notifications timeout in ms" |
| default 10000 |
| help |
| The amount of time, in milliseconds, that should elapse between |
| the start and end of sysmon SSR notifications, before a warning |
| is emitted. |
| |
| config SSR_SUBSYS_NOTIF_TIMEOUT |
| depends on SETUP_SSR_NOTIF_TIMEOUTS |
| int "SSR Subsystem notifier timeout in ms" |
| default 10000 |
| help |
| The amount of time, in milliseconds, that should elapse between |
| the start and end of SSR notifications through the subsystem |
| notifier, before a warning is emitted. |
| |
| config PANIC_ON_SSR_NOTIF_TIMEOUT |
| bool "Trigger kernel panic when notification timeout expires" |
| depends on SETUP_SSR_NOTIF_TIMEOUTS |
| help |
| Trigger a kernel panic when communication between subsystems |
| through sysmon is taking too long. Also trigger a kernel panic |
| if invoking the callbacks registered with a particular subsystem's |
| notifications by the subsystem notifier framework is taking too long. |
| This is a debugging feature. |
| |
| config QCOM_SECURE_BUFFER |
| bool "Helper functions for securing buffers through TZ" |
| help |
| Say 'Y' here for targets that need to call into TZ to secure |
| memory buffers. This ensures that only the correct clients can |
| use this memory and no unauthorized access is made to the |
| buffer |
| |
| config MSM_REMOTEQDSS |
| bool "Allow debug tools to enable events on other processors" |
| depends on QCOM_SCM && DEBUG_FS |
| help |
| Other onchip processors/execution environments may support debug |
| events. Provide a sysfs interface for debug tools to dynamically |
| enable/disable these events. Interface located in |
| /sys/class/remoteqdss. |
| |
| config MSM_TZ_SMMU |
| depends on ARCH_MSM8953 || ARCH_QCS405 |
| bool "Helper functions for SMMU configuration through TZ" |
| help |
| Say 'Y' here for targets that need to call into TZ to configure |
| SMMUs for any reason (for example, for errata workarounds or |
| configuration of SMMU virtualization). |
| |
| If unsure, say N. |
| |
| config MSM_SERVICE_LOCATOR |
| bool "Service Locator" |
| depends on QCOM_QMI_HELPERS |
| help |
| The Service Locator provides a library to retrieve location |
| information given a service identifier. Location here translates |
| to what process domain exports the service, and which subsystem |
| that process domain will execute in. |
| |
| config MSM_SERVICE_NOTIFIER |
| bool "Service Notifier" |
| depends on MSM_SERVICE_LOCATOR && MSM_SUBSYSTEM_RESTART |
| help |
| The Service Notifier provides a library for a kernel client to |
| register for state change notifications regarding a remote service. |
| A remote service here refers to a process providing certain services |
| like audio, the identifier for which is provided by the service |
| locator. |
| |
| config MSM_SUBSYSTEM_RESTART |
| bool "MSM Subsystem Restart" |
| help |
| This option enables the MSM subsystem restart framework. |
| |
| The MSM subsystem restart framework provides support to boot, |
| shutdown, and restart subsystems with a reference counted API. |
| It also notifies userspace of transitions between these states via |
| sysfs. |
| |
| config MSM_PIL |
| bool "Peripheral image loading" |
| select FW_LOADER |
| default n |
| help |
| Some peripherals need to be loaded into memory before they can be |
| brought out of reset. |
| |
| Say yes to support these devices. |
| |
| config MSM_SYSMON_GLINK_COMM |
| bool "MSM System Monitor communication support using GLINK transport" |
| depends on MSM_GLINK && MSM_SUBSYSTEM_RESTART |
| help |
| This option adds support for MSM System Monitor APIs using the GLINK |
| transport layer. The APIs provided may be used for notifying |
| subsystems within the SoC about other subsystems' power-up/down |
| state-changes. |
| |
| config MSM_SYSMON_QMI_COMM |
| bool "MSM System Monitor communication support using QMI transport" |
| depends on QCOM_QMI_HELPERS && MSM_SUBSYSTEM_RESTART |
| help |
| This option adds support for MSM System Monitor APIs using the |
| QMI layer. The APIs provided may be used for notifying |
| subsystems within the SoC about other subsystems' power-up/down |
| state-changes. |
| |
| config MSM_PIL_SSR_GENERIC |
| tristate "MSM Subsystem Boot Support" |
| depends on MSM_PIL && MSM_SUBSYSTEM_RESTART |
| help |
| Support for booting and shutting down MSM Subsystem processors. |
| This driver also monitors the SMSM status bits and the watchdog |
| interrupt for the subsystem and restarts it on a watchdog bite |
| or a fatal error. Subsystems include LPASS, Venus, VPU, WCNSS and |
| BCSS. |
| config MSM_BOOT_STATS |
| bool "Use MSM boot stats reporting" |
| help |
| Use this to report msm boot stats such as bootloader throughput, |
| display init, total boot time. |
| This figures are reported in mpm sleep clock cycles and have a |
| resolution of 31 bits as 1 bit is used as an overflow check. |
| |
| config QCOM_DCC_V2 |
| bool "Qualcomm Technologies Data Capture and Compare enigne support for V2" |
| help |
| This option enables driver for Data Capture and Compare engine. DCC |
| driver provides interface to configure DCC block and read back |
| captured data from DCC's internal SRAM. |
| |
| config QCOM_EUD |
| tristate "QTI Embedded USB Debugger (EUD)" |
| depends on ARCH_QCOM |
| select SERIAL_CORE |
| help |
| The EUD (Embedded USB Debugger) is a mini-USB hub implemented |
| on chip to support the USB-based debug and trace capabilities. |
| This module enables support for Qualcomm Technologies, Inc. |
| Embedded USB Debugger (EUD). |
| If unsure, say N. |
| |
| config QCOM_MINIDUMP |
| bool "QCOM Minidump Support" |
| depends on QCOM_SMEM && POWER_RESET_QCOM |
| help |
| This enables minidump feature. It allows various clients to |
| register to dump their state at system bad state (panic/WDT,etc.,). |
| Minidump would dump all registered entries, only when DLOAD mode |
| is enabled. |
| |
| config MINIDUMP_MAX_ENTRIES |
| int "Minidump Maximum num of entries" |
| default 200 |
| depends on QCOM_MINIDUMP |
| help |
| This defines maximum number of entries to be allocated for application |
| subsytem in Minidump table. |
| |
| config QCOM_APR |
| tristate "Qualcomm APR Bus (Asynchronous Packet Router)" |
| depends on ARCH_QCOM |
| depends on RPMSG |
| help |
| Enable APR IPC protocol support between |
| application processor and QDSP6. APR is |
| used by audio driver to configure QDSP6 |
| ASM, ADM and AFE modules. |
| |
| config MSM_CORE_HANG_DETECT |
| tristate "MSM Core Hang Detection Support" |
| help |
| This enables the core hang detection module. It causes SoC |
| reset on core hang detection and collects the core context |
| for hang. By using sysfs entries core hang detection can be |
| enabled or disabled dynamically. |
| |
| config MSM_GLADIATOR_HANG_DETECT |
| tristate "MSM Gladiator Hang Detection Support" |
| help |
| This enables the gladiator hang detection module. |
| If the configured threshold is reached, it causes SoC reset on |
| gladiator hang detection and collects the context for the |
| gladiator hang. |
| |
| config MSM_GLADIATOR_ERP |
| tristate "GLADIATOR coherency interconnect error reporting driver" |
| help |
| Support dumping debug information for the GLADIATOR |
| cache interconnect in the error interrupt handler. |
| Meant to be used for debug scenarios only. |
| |
| If unsure, say N. |
| |
| config PANIC_ON_GLADIATOR_ERROR |
| depends on MSM_GLADIATOR_ERP |
| bool "Panic on GLADIATOR error report" |
| help |
| Panic upon detection of an Gladiator coherency interconnect error |
| in order to support dumping debug information. |
| Meant to be used for debug scenarios only. |
| |
| If unsure, say N. |
| |
| config QCOM_FSA4480_I2C |
| bool "Fairchild FSA4480 chip with I2C" |
| select REGMAP_I2C |
| depends on I2C |
| help |
| Support for the Fairchild FSA4480 IC switch chip controlled |
| using I2C. This driver provides common support |
| for accessing the device, switching between USB and Audio |
| modes, changing orientation. |
| |
| config QCOM_WATCHDOG_V2 |
| bool "QTI Watchdog Support" |
| depends on ARCH_QCOM |
| help |
| This enables the watchdog module. It causes kernel panic if the |
| watchdog times out. It allows for detection of cpu hangs and |
| deadlocks. It does not run during the bootup process, so it will |
| not catch any early lockups. |
| |
| config QCOM_FORCE_WDOG_BITE_ON_PANIC |
| bool "QCOM force watchdog bite" |
| depends on QCOM_WATCHDOG_V2 |
| help |
| This forces a watchdog bite when the device restarts due to a |
| kernel panic. On certain MSM SoCs, this provides us |
| additional debugging information. |
| |
| |
| config QCOM_WDOG_IPI_ENABLE |
| bool "Qcom WDT pet optimization" |
| depends on QCOM_WATCHDOG_V2 |
| default n |
| help |
| When this option is enabled, watchdog sends IPI to cores in low power |
| mode also. For power optimizations, by default watchdog don't ping |
| cores in low power mode at pettime. |
| |
| To track CPUs health on LPM, or on debug builds enable it. |
| |
| config QCOM_BUS_SCALING |
| bool "Bus scaling driver" |
| help |
| This option enables bus scaling on MSM devices. Bus scaling |
| allows devices to request the clocks be set to rates sufficient |
| for the active devices needs without keeping the clocks at max |
| frequency when a slower speed is sufficient. |
| |
| config QCOM_BUS_CONFIG_RPMH |
| bool "RPMH Bus scaling driver" |
| depends on QCOM_BUS_SCALING |
| help |
| This option enables bus scaling using QCOM specific hardware |
| accelerators. It enables the translation of bandwidth requests |
| from logical nodes to hardware nodes controlled by the BCM (Bus |
| Clock Manager) |
| |
| config MSM_SPCOM |
| depends on QCOM_GLINK |
| bool "Secure Processor Communication over GLINK" |
| help |
| spcom driver allows loading Secure Processor Applications and |
| sending messages to Secure Processor Applications. |
| spcom provides interface to both user space app and kernel driver. |
| It is using glink as the transport layer, which provides multiple |
| logical channels over single physical channel. |
| The physical layer is based on shared memory and interrupts. |
| spcom provides clients/server API, although currently only one client |
| or server is allowed per logical channel. |
| |
| config QSEE_IPC_IRQ |
| bool "QSEE interrupt manager" |
| help |
| The QSEE IPC IRQ controller manages the interrupts from the QTI |
| secure execution environment. This interrupt controller will use |
| the registers in the spcs region to mask and clear interrupts. |
| Clients can use this driver to avoid adding common interrupt handling |
| code. |
| |
| config MSM_SPSS_UTILS |
| depends on MSM_PIL |
| bool "Secure Processor Utilities" |
| help |
| spss-utils driver selects Secure Processor firmware file name. |
| The firmware file name for dev, test or production is selected |
| based on two fuses. |
| Different file name is used for differnt SPSS HW versions, |
| because the SPSS firmware size is too small to support multiple |
| HW versions. |
| |
| config QSEE_IPC_IRQ_BRIDGE |
| tristate "QSEE IPC Interrupt Bridge" |
| select QSEE_IPC_IRQ |
| help |
| This module enables bridging an Inter-Processor Communication(IPC) |
| interrupt from a remote subsystem directed towards |
| Qualcomm Technologies, Inc. Secure Execution Environment(QSEE) to |
| userspace. The interrupt will be propagated through a character device |
| that userspace clients can poll on. |
| |
| config QCOM_GLINK |
| tristate "GLINK Probe Helper" |
| depends on RPMSG_QCOM_GLINK_SMEM |
| help |
| This enables the GLINK Probe module. The GLINK RPMSG Plugin is |
| currently designed to plugin with the remote proc framework as a |
| subdev. This module is responsible for creating the glink transports |
| when remote proc is disabled. |
| |
| config QCOM_GLINK_PKT |
| tristate "Enable device interface for GLINK packet channels" |
| depends on QCOM_GLINK |
| help |
| G-link packet driver provides the interface for the userspace |
| clients to communicate over G-Link via device nodes. |
| This enable the userspace clients to read and write to |
| some glink packets channel. |
| |
| config QCOM_SMP2P_SLEEPSTATE |
| bool "SMP2P Sleepstate notifier" |
| depends on QCOM_SMP2P |
| help |
| When this option is enabled, notifications are sent to remote procs |
| for the power state changes on the local processor. The notifications |
| are sent through the smp2p framework. This driver can also receive |
| notifications from the remote to prevent suspend on the local |
| processor. |
| |
| config QCOM_QDSS_BRIDGE |
| bool "Configure bridge driver for QTI/Qualcomm Technologies, Inc. MDM" |
| depends on MHI_BUS |
| help |
| The driver will help route diag traffic from modem side over the QDSS |
| sub-system to USB on APSS side. The driver acts as a bridge between the |
| MHI and USB interface. |
| If unsure, say N. |
| |
| config MSM_CDSP_LOADER |
| tristate "CDSP loader support" |
| help |
| This enables the CDSP loader driver that loads the CDSP |
| firmware images and brings the compute DSP out of reset |
| for platforms that have one. |
| Say M if you want to enable this module. |
| |
| config QTI_SYSTEM_PM |
| bool |
| |
| config QCOM_SMCINVOKE |
| bool "Secure QSEE Support" |
| help |
| Enable SMCInvoke driver which supports capability based secure |
| communication between QTI Secure Execution Environment (QSEE) |
| and high level operating system. It exposes APIs for both |
| userspace and kernel clients. |
| |
| config MSM_EVENT_TIMER |
| bool "Event timer" |
| help |
| This option enables a modules that manages a list of event timers |
| that need to be monitored by the PM. The enables the PM code to |
| monitor events that require the core to be awake and ready to |
| handle the event. |
| |
| config MSM_PM |
| depends on PM |
| select MSM_IDLE_STATS if DEBUG_FS |
| select CPU_IDLE_MULTIPLE_DRIVERS |
| select QTI_SYSTEM_PM if QCOM_RPMH |
| bool "Qualcomm Technologies, Inc. (QTI) Power Management Drivers" |
| help |
| Platform specific power driver to manage cores and l2 low power |
| modes. It interface with various system driver and put the cores |
| into low power modes. It implements OS initiated scheme and |
| determines last CPU to call into PSCI for cluster Low power |
| modes. |
| |
| if MSM_PM |
| menuconfig MSM_IDLE_STATS |
| bool "Collect idle statistics" |
| help |
| Collect cores various low power mode idle statistics |
| and export them in proc/msm_pm_stats. User can read |
| this data and determine what low power modes and how |
| many times cores have entered into LPM modes. |
| |
| if MSM_IDLE_STATS |
| |
| config MSM_IDLE_STATS_FIRST_BUCKET |
| int "First bucket time" |
| default 62500 |
| help |
| Upper time limit in nanoseconds of first bucket. |
| |
| config MSM_IDLE_STATS_BUCKET_SHIFT |
| int "Bucket shift" |
| default 2 |
| |
| config MSM_IDLE_STATS_BUCKET_COUNT |
| int "Bucket count" |
| default 10 |
| |
| config MSM_SUSPEND_STATS_FIRST_BUCKET |
| int "First bucket time for suspend" |
| default 1000000000 |
| help |
| Upper time limit in nanoseconds of first bucket of the |
| histogram. This is for collecting statistics on suspend. |
| |
| endif # MSM_IDLE_STATS |
| endif # MSM_PM |
| |
| config QTI_L2_REUSE |
| bool "Qualcomm Technologies Inc (QTI) L2 reuse" |
| depends on ARCH_QCOM |
| help |
| This module allows to configure the L2 reuse feature dynamically |
| to let the power collapsed cluster's L2 cache usage by the active |
| cluster cpu. Use sysfs interface to control enabling this feature. |
| |
| config QTI_RPM_STATS_LOG |
| bool "Qualcomm Technologies RPM Stats Driver" |
| depends on QCOM_RPMH || MSM_RPM_SMD |
| help |
| This option enables a driver which reads RPM messages from a shared |
| memory location. These messages provide statistical information about |
| the low power modes that RPM enters. The drivers outputs the message |
| via a sysfs node. |
| |
| config QTI_DDR_STATS_LOG |
| tristate "Qualcomm Technologies Inc (QTI) DDR Stats Driver" |
| depends on QCOM_RPMH |
| help |
| This option enables a driver which reads DDR statistical information |
| from AOP shared memory location such as DDR low power modes and DDR |
| frequency residency and counts. The driver outputs information using |
| sysfs. |
| |
| config MSM_JTAGV8 |
| bool "Debug and ETM trace support across power collapse for ARMv8" |
| default y if CORESIGHT_SOURCE_ETM4X |
| help |
| Enables support for debugging (specifically breakpoints) and ETM |
| processor tracing across power collapse both for JTag and OS hosted |
| software running on ARMv8 target. Enabling this will ensure debug |
| and ETM registers are saved and restored across power collapse. |
| If unsure, say 'N' here to avoid potential power, performance and |
| memory penalty. |
| config QTEE_SHM_BRIDGE |
| bool "QTI TEE shared memory bridge" |
| help |
| QTEE shared memory bridge driver provides kernel APIs to share |
| memory between trustzone & other VMs through shared memory bridge. |
| It allows kernel clients to create bridge, delete bridge, and do |
| memory sub-allocation and free from the default kernel bridge |
| created by bridge driver. |
| |
| source "drivers/soc/qcom/memshare/Kconfig" |
| config MSM_PERFORMANCE |
| tristate "msm performance driver to support userspace fmin/fmax request" |
| default n |
| help |
| This driver can restrict max freq or min freq of cpu cluster |
| when requested by the userspace by changing the cpufreq policy |
| fmin and fmax. The user space can request the cpu freq change by |
| writing cpu#:freq values |
| config QMP_DEBUGFS_CLIENT |
| bool "Debugfs Client to communicate with AOP using QMP protocol" |
| depends on DEBUG_FS |
| help |
| This options enables a driver which allows clients to send messages |
| to Alway On processor using QMP transport. |
| |
| config QCOM_CDSP_RM |
| bool "CDSP request manager" |
| depends on QCOM_GLINK |
| help |
| This driver serves CDSP requests for CPU L3 clock and CPU QoS thus |
| improving CDSP performance. Using this driver, CDSP can set appropriate |
| CPU L3 clock for improving IO-Coherent throughput and opt for QoS mode |
| to improve RPC latency. The driver also registers cooling devices for |
| CDSP subsystem and implements Cx ipeak limit management. |
| |
| config QCOM_QHEE_ENABLE_MEM_PROTECTION |
| bool "QHEE enable kernel memory protection" |
| depends on QCOM_SCM |
| help |
| When this option is enabled, an SCM call will be invoked to enable |
| kernel memory protection in stage 2 memory mappings on kernel boot. |
| This is part of a security feature in QHEE and need to be enabled by |
| default. |
| |
| config QCOM_CX_IPEAK |
| bool "Common driver to handle Cx iPeak limitation" |
| help |
| Cx ipeak HW module is used to limit the current drawn by various |
| subsystem blocks on Cx power rail. Each client needs to set their |
| bit in tcsr register if it is going to cross its own threshold. |
| If all clients are going to cross their thresholds then Cx ipeak |
| hw module will raise an interrupt to cDSP block to throttle cDSP fmax. |
| |
| config QTI_CRYPTO_COMMON |
| tristate "Enable common crypto functionality used for FBE" |
| depends on BLK_INLINE_ENCRYPTION |
| help |
| Say 'Y' to enable the common crypto implementation to be used by |
| different storage layers such as UFS and EMMC for file based hardware |
| encryption. This library implements API to program and evict |
| keys using Trustzone or Hardware Key Manager. |
| |
| config QTI_CRYPTO_TZ |
| tristate "Enable Trustzone to be used for FBE" |
| depends on QTI_CRYPTO_COMMON |
| help |
| Say 'Y' to enable routing crypto requests to Trustzone while |
| performing hardware based file encryption. This means keys are |
| programmed and managed through SCM calls to TZ where ICE driver |
| will configure keys. |
| endmenu |
| |
| config QCOM_HYP_CORE_CTL |
| bool "CPU reservation scheme for Hypervisor" |
| depends on OKL4_GUEST |
| help |
| This driver reserve the specified CPUS by isolating them. The reserved |
| CPUs can be assigned to the other guest OS by the hypervisor. |
| An offline CPU is considered as a reserved CPU since this OS can't use |
| it. |
| |
| config QTI_HW_KEY_MANAGER |
| tristate "Enable QTI Hardware Key Manager for storage encryption" |
| default n |
| help |
| Say 'Y' to enable the hardware key manager driver used to operate |
| and access key manager hardware block. This is used to interface with |
| HWKM hardware to perform key operations from the kernel which will |
| be used for storage encryption. |
| |
| source "drivers/soc/qcom/icnss2/Kconfig" |
| |
| config ICNSS |
| tristate "Platform driver for Q6 integrated connectivity" |
| select CNSS_UTILS |
| help |
| This module adds support for Q6 integrated WLAN connectivity |
| subsystem. This module is responsible for communicating WLAN on/off |
| control messages to FW over QMI channel. It is also responsible for |
| handling WLAN PD restart notifications. |
| |
| config ICNSS_DEBUG |
| bool "ICNSS debug support" |
| depends on ICNSS |
| help |
| Say 'Y' here to enable ICNSS driver debug support. Debug support |
| primarily consists of logs consisting of information related to |
| hardware register access and enabling BUG_ON for certain cases to aid |
| the debugging. |
| |
| config ICNSS_QMI |
| bool "ICNSS QMI support" |
| depends on ICNSS |
| help |
| Say 'Y' here to enable ICNSS QMI support. ICNSS driver will use |
| QMI framework to communicate with WLAN FW. It will send coldboot |
| handshake messages to WLAN FW, which includes hardware capabilities |
| and configurations. It also send WLAN on/off control message to FW |
| over QMI channel. |