| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (c) 2016-2020, The Linux Foundation. All rights reserved. |
| */ |
| |
| #define pr_fmt(fmt) "LCDB: %s: " fmt, __func__ |
| |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/interrupt.h> |
| #include <linux/ktime.h> |
| #include <linux/module.h> |
| #include <linux/of_irq.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/driver.h> |
| #include <linux/regulator/of_regulator.h> |
| #include <linux/regulator/machine.h> |
| #include <linux/qpnp/qpnp-revid.h> |
| |
| #define QPNP_LCDB_REGULATOR_DRIVER_NAME "qcom,qpnp-lcdb-regulator" |
| |
| /* LCDB */ |
| #define LCDB_STS1_REG 0x08 |
| |
| #define INT_RT_STATUS_REG 0x10 |
| #define VREG_OK_RT_STS_BIT BIT(0) |
| #define SC_ERROR_RT_STS_BIT BIT(1) |
| |
| #define LCDB_STS3_REG 0x0A |
| #define LDO_VREG_OK_BIT BIT(7) |
| |
| #define LCDB_STS4_REG 0x0B |
| #define NCP_VREG_OK_BIT BIT(7) |
| |
| #define LCDB_AUTO_TOUCH_WAKE_CTL_REG 0x40 |
| #define EN_AUTO_TOUCH_WAKE_BIT BIT(7) |
| #define ATTW_TOFF_TIME_MASK GENMASK(3, 2) |
| #define ATTW_TON_TIME_MASK GENMASK(1, 0) |
| #define ATTW_TOFF_TIME_SHIFT 2 |
| #define ATTW_MIN_MS 4 |
| #define ATTW_MAX_MS 32 |
| |
| #define LCDB_BST_OUTPUT_VOLTAGE_REG 0x41 |
| #define PM660_BST_OUTPUT_VOLTAGE_MASK GENMASK(4, 0) |
| #define BST_OUTPUT_VOLTAGE_MASK GENMASK(5, 0) |
| |
| #define LCDB_MODULE_RDY_REG 0x45 |
| #define MODULE_RDY_BIT BIT(7) |
| |
| #define LCDB_ENABLE_CTL1_REG 0x46 |
| #define MODULE_EN_BIT BIT(7) |
| #define HWEN_RDY_BIT BIT(6) |
| |
| /* BST */ |
| #define LCDB_BST_PD_CTL_REG 0x47 |
| #define BOOST_DIS_PULLDOWN_BIT BIT(1) |
| #define BOOST_PD_STRENGTH_BIT BIT(0) |
| |
| #define LCDB_BST_ILIM_CTL_REG 0x4B |
| #define EN_BST_ILIM_BIT BIT(7) |
| #define SET_BST_ILIM_MASK GENMASK(2, 0) |
| #define MIN_BST_ILIM_MA 200 |
| #define MAX_BST_ILIM_MA 1600 |
| |
| #define LCDB_PS_CTL_REG 0x50 |
| #define EN_PS_BIT BIT(7) |
| #define PM660_PS_THRESH_MASK GENMASK(1, 0) |
| #define PS_THRESH_MASK GENMASK(2, 0) |
| #define MIN_BST_PS_MA 50 |
| #define MAX_BST_PS_MA 80 |
| |
| #define LCDB_RDSON_MGMNT_REG 0x53 |
| #define NFET_SW_SIZE_MASK GENMASK(3, 2) |
| #define NFET_SW_SIZE_SHIFT 2 |
| #define PFET_SW_SIZE_MASK GENMASK(1, 0) |
| |
| #define LCDB_BST_VREG_OK_CTL_REG 0x55 |
| #define BST_VREG_OK_DEB_MASK GENMASK(1, 0) |
| |
| #define LCDB_BST_SS_CTL_REG 0x5B |
| #define BST_SS_TIME_MASK GENMASK(1, 0) |
| #define BST_PRECHG_SHORT_ALARM_SHIFT 2 |
| #define BST_PRECHARGE_DONE_DEB_BIT BIT(4) |
| #define BST_SS_TIME_OVERRIDE_SHIFT 5 |
| |
| #define BST_SS_TIME_OVERRIDE_0MS 0 |
| #define BST_SS_TIME_OVERRIDE_0P5_MS 1 |
| #define BST_SS_TIME_OVERRIDE_1MS 2 |
| #define BST_SS_TIME_OVERRIDE_2MS 3 |
| |
| #define EN_BST_PRECHG_SHORT_ALARM 0 |
| #define DIS_BST_PRECHG_SHORT_ALARM 1 |
| |
| #define LCDB_SOFT_START_CTL_REG 0x5F |
| |
| #define LCDB_MISC_CTL_REG 0x60 |
| #define AUTO_GM_EN_BIT BIT(4) |
| #define EN_TOUCH_WAKE_BIT BIT(3) |
| #define DIS_SCP_BIT BIT(0) |
| |
| #define LCDB_PFM_CTL_REG 0x62 |
| #define EN_PFM_BIT BIT(7) |
| #define BYP_BST_SOFT_START_COMP_BIT BIT(0) |
| #define PFM_HYSTERESIS_SHIFT 4 |
| #define PFM_CURRENT_SHIFT 2 |
| |
| #define LCDB_PWRUP_PWRDN_CTL_REG 0x66 |
| #define PWRUP_DELAY_MASK GENAMSK(3, 2) |
| #define PWRDN_DELAY_MASK GENMASK(1, 0) |
| #define PWRDN_DELAY_MIN_MS 0 |
| #define PWRDN_DELAY_MAX_MS 8 |
| |
| /* LDO */ |
| #define LCDB_LDO_OUTPUT_VOLTAGE_REG 0x71 |
| #define SET_OUTPUT_VOLTAGE_MASK GENMASK(4, 0) |
| |
| #define LCDB_LDO_VREG_OK_CTL_REG 0x75 |
| #define VREG_OK_DEB_MASK GENMASK(1, 0) |
| |
| #define LCDB_LDO_PD_CTL_REG 0x77 |
| #define LDO_DIS_PULLDOWN_BIT BIT(1) |
| #define LDO_PD_STRENGTH_BIT BIT(0) |
| |
| #define LCDB_LDO_FORCE_PD_CTL_REG 0x79 |
| #define LDO_FORCE_PD_EN_BIT BIT(0) |
| #define LDO_FORCE_PD_MODE BIT(7) |
| |
| #define LCDB_LDO_ILIM_CTL1_REG 0x7B |
| #define EN_LDO_ILIM_BIT BIT(7) |
| #define SET_LDO_ILIM_MASK GENMASK(2, 0) |
| #define MIN_LDO_ILIM_MA 110 |
| #define MAX_LDO_ILIM_MA 460 |
| #define LDO_ILIM_STEP_MA 50 |
| |
| #define LCDB_LDO_ILIM_CTL2_REG 0x7C |
| |
| #define LCDB_LDO_SOFT_START_CTL_REG 0x7F |
| #define SOFT_START_MASK GENMASK(1, 0) |
| |
| /* NCP */ |
| #define LCDB_NCP_OUTPUT_VOLTAGE_REG 0x81 |
| |
| #define LCDB_NCP_VREG_OK_CTL_REG 0x85 |
| |
| #define LCDB_NCP_PD_CTL_REG 0x87 |
| #define NCP_DIS_PULLDOWN_BIT BIT(1) |
| #define NCP_PD_STRENGTH_BIT BIT(0) |
| |
| #define LCDB_NCP_ILIM_CTL1_REG 0x8B |
| #define EN_NCP_ILIM_BIT BIT(7) |
| #define SET_NCP_ILIM_MASK GENMASK(1, 0) |
| #define MIN_NCP_ILIM_MA 260 |
| #define MAX_NCP_ILIM_MA 810 |
| |
| #define LCDB_NCP_ILIM_CTL2_REG 0x8C |
| |
| #define LCDB_NCP_SOFT_START_CTL_REG 0x8F |
| |
| /* common for BST/NCP/LDO */ |
| #define MIN_DBC_US 2 |
| #define MAX_DBC_US 32 |
| |
| #define MIN_SOFT_START_US 0 |
| #define MAX_SOFT_START_US 2000 |
| |
| #define PM660_BST_HEADROOM_DEFAULT_MV 200 |
| #define BST_HEADROOM_DEFAULT_MV 150 |
| |
| #define PMIC5_LCDB_OFF_ON_DELAY_US 20000 |
| |
| struct ldo_regulator { |
| struct regulator_desc rdesc; |
| struct regulator_dev *rdev; |
| struct device_node *node; |
| |
| /* LDO DT params */ |
| int pd; |
| int pd_strength; |
| int ilim_ma; |
| int soft_start_us; |
| int vreg_ok_dbc_us; |
| int voltage_mv; |
| int prev_voltage_mv; |
| }; |
| |
| struct ncp_regulator { |
| struct regulator_desc rdesc; |
| struct regulator_dev *rdev; |
| struct device_node *node; |
| |
| /* NCP DT params */ |
| int pd; |
| int pd_strength; |
| int ilim_ma; |
| int soft_start_us; |
| int vreg_ok_dbc_us; |
| int voltage_mv; |
| int prev_voltage_mv; |
| }; |
| |
| struct bst_params { |
| struct device_node *node; |
| |
| /* BST DT params */ |
| int pd; |
| int pd_strength; |
| int ilim_ma; |
| int ps; |
| int ps_threshold; |
| int soft_start_us; |
| int vreg_ok_dbc_us; |
| int voltage_mv; |
| u16 headroom_mv; |
| }; |
| |
| struct qpnp_lcdb { |
| struct device *dev; |
| struct platform_device *pdev; |
| struct regmap *regmap; |
| struct class lcdb_class; |
| struct pmic_revid_data *pmic_rev_id; |
| u32 base; |
| u32 wa_flags; |
| int sc_irq; |
| int pwrdn_delay_ms; |
| |
| /* TTW params */ |
| bool ttw_enable; |
| bool ttw_mode_sw; |
| |
| /* status parameters */ |
| bool lcdb_enabled; |
| bool settings_saved; |
| bool lcdb_sc_disable; |
| bool voltage_step_ramp; |
| /* Tracks the secure UI mode entry/exit */ |
| bool secure_mode; |
| int sc_count; |
| ktime_t sc_module_enable_time; |
| |
| struct mutex lcdb_mutex; |
| struct mutex read_write_mutex; |
| struct bst_params bst; |
| struct ldo_regulator ldo; |
| struct ncp_regulator ncp; |
| }; |
| |
| struct settings { |
| u16 address; |
| u8 value; |
| bool sec_access; |
| bool valid; |
| }; |
| |
| enum lcdb_module { |
| LDO, |
| NCP, |
| BST, |
| LDO_NCP, |
| }; |
| |
| enum pfm_hysteresis { |
| PFM_HYST_15MV, |
| PFM_HYST_25MV, |
| PFM_HYST_35MV, |
| PFM_HYST_45MV, |
| }; |
| |
| enum pfm_peak_current { |
| PFM_PEAK_CURRENT_300MA, |
| PFM_PEAK_CURRENT_400MA, |
| PFM_PEAK_CURRENT_500MA, |
| PFM_PEAK_CURRENT_600MA, |
| }; |
| |
| enum rdson_fet_size { |
| RDSON_QUARTER, |
| RDSON_HALF, |
| RDSON_THREE_FOURTH, |
| RDSON_FULLSIZE, |
| }; |
| |
| enum lcdb_settings_index { |
| LCDB_BST_PD_CTL = 0, |
| LCDB_RDSON_MGMNT, |
| LCDB_MISC_CTL, |
| LCDB_SOFT_START_CTL, |
| LCDB_PFM_CTL, |
| LCDB_PWRUP_PWRDN_CTL, |
| LCDB_LDO_PD_CTL, |
| LCDB_LDO_SOFT_START_CTL, |
| LCDB_NCP_PD_CTL, |
| LCDB_NCP_SOFT_START_CTL, |
| LCDB_BST_SS_CTL, |
| LCDB_LDO_VREG_OK_CTL, |
| LCDB_SETTING_MAX, |
| }; |
| |
| enum lcdb_wa_flags { |
| NCP_SCP_DISABLE_WA = BIT(0), |
| FORCE_PD_ENABLE_WA = BIT(1), |
| }; |
| |
| static u32 soft_start_us[] = { |
| 0, |
| 500, |
| 1000, |
| 2000, |
| }; |
| |
| static u32 dbc_us[] = { |
| 2, |
| 4, |
| 16, |
| 32, |
| }; |
| |
| static u32 ncp_ilim_ma[] = { |
| 260, |
| 460, |
| 640, |
| 810, |
| }; |
| |
| static const u32 pwrup_pwrdn_ms[] = { |
| 0, |
| 1, |
| 4, |
| 8, |
| }; |
| |
| #define SETTING(_id, _sec_access, _valid) \ |
| [_id] = { \ |
| .address = _id##_REG, \ |
| .sec_access = _sec_access, \ |
| .valid = _valid \ |
| } \ |
| |
| static int qpnp_lcdb_set_voltage_step(struct qpnp_lcdb *lcdb, |
| int voltage_start_mv, u8 type); |
| |
| static int qpnp_lcdb_set_voltage(struct qpnp_lcdb *lcdb, |
| int voltage_mv, u8 type); |
| |
| static bool is_between(int value, int min, int max) |
| { |
| if (value < min || value > max) |
| return false; |
| return true; |
| } |
| |
| static int qpnp_lcdb_read(struct qpnp_lcdb *lcdb, |
| u16 addr, u8 *value, u8 count) |
| { |
| int rc = 0; |
| |
| mutex_lock(&lcdb->read_write_mutex); |
| rc = regmap_bulk_read(lcdb->regmap, addr, value, count); |
| if (rc < 0) |
| pr_err("Failed to read from addr=0x%02x rc=%d\n", addr, rc); |
| mutex_unlock(&lcdb->read_write_mutex); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_write(struct qpnp_lcdb *lcdb, |
| u16 addr, u8 *value, u8 count) |
| { |
| int rc; |
| |
| mutex_lock(&lcdb->read_write_mutex); |
| rc = regmap_bulk_write(lcdb->regmap, addr, value, count); |
| if (rc < 0) |
| pr_err("Failed to write to addr=0x%02x rc=%d\n", addr, rc); |
| mutex_unlock(&lcdb->read_write_mutex); |
| |
| return rc; |
| } |
| |
| #define SEC_ADDRESS_REG 0xD0 |
| #define SECURE_UNLOCK_VALUE 0xA5 |
| static int qpnp_lcdb_secure_write(struct qpnp_lcdb *lcdb, |
| u16 addr, u8 value) |
| { |
| int rc; |
| u8 val = SECURE_UNLOCK_VALUE; |
| u8 pmic_subtype = lcdb->pmic_rev_id->pmic_subtype; |
| |
| mutex_lock(&lcdb->read_write_mutex); |
| if (pmic_subtype == PM660L_SUBTYPE) { |
| rc = regmap_write(lcdb->regmap, lcdb->base + SEC_ADDRESS_REG, |
| val); |
| if (rc < 0) { |
| pr_err("Failed to unlock register rc=%d\n", rc); |
| goto fail_write; |
| } |
| } |
| rc = regmap_write(lcdb->regmap, addr, value); |
| if (rc < 0) |
| pr_err("Failed to write to addr=0x%02x rc=%d\n", addr, rc); |
| |
| fail_write: |
| mutex_unlock(&lcdb->read_write_mutex); |
| return rc; |
| } |
| |
| static int qpnp_lcdb_masked_write(struct qpnp_lcdb *lcdb, |
| u16 addr, u8 mask, u8 value) |
| { |
| int rc = 0; |
| |
| mutex_lock(&lcdb->read_write_mutex); |
| rc = regmap_update_bits(lcdb->regmap, addr, mask, value); |
| if (rc < 0) |
| pr_err("Failed to write addr=0x%02x value=0x%02x rc=%d\n", |
| addr, value, rc); |
| mutex_unlock(&lcdb->read_write_mutex); |
| |
| return rc; |
| } |
| |
| static bool is_lcdb_enabled(struct qpnp_lcdb *lcdb) |
| { |
| int rc; |
| u8 val = 0; |
| |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + LCDB_ENABLE_CTL1_REG, &val, 1); |
| if (rc < 0) |
| pr_err("Failed to read ENABLE_CTL1 rc=%d\n", rc); |
| |
| return rc ? false : !!(val & MODULE_EN_BIT); |
| } |
| |
| static int dump_status_registers(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| u8 sts[6] = {0}; |
| |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_STS1_REG, &sts[0], 6); |
| if (rc < 0) { |
| pr_err("Failed to write to STS registers rc=%d\n", rc); |
| } else { |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + LCDB_STS1_REG, sts, 6); |
| if (rc < 0) |
| pr_err("Failed to read lcdb status rc=%d\n", rc); |
| else |
| pr_err("STS1=0x%02x STS2=0x%02x STS3=0x%02x STS4=0x%02x STS5=0x%02x, STS6=0x%02x\n", |
| sts[0], sts[1], sts[2], sts[3], sts[4], sts[5]); |
| } |
| |
| return rc; |
| } |
| |
| static struct settings lcdb_settings_pm660l[] = { |
| SETTING(LCDB_BST_PD_CTL, false, true), |
| SETTING(LCDB_RDSON_MGMNT, false, true), |
| SETTING(LCDB_MISC_CTL, false, true), |
| SETTING(LCDB_SOFT_START_CTL, false, true), |
| SETTING(LCDB_PFM_CTL, false, true), |
| SETTING(LCDB_PWRUP_PWRDN_CTL, true, true), |
| SETTING(LCDB_LDO_PD_CTL, false, true), |
| SETTING(LCDB_LDO_SOFT_START_CTL, false, true), |
| SETTING(LCDB_NCP_PD_CTL, false, true), |
| SETTING(LCDB_NCP_SOFT_START_CTL, false, true), |
| SETTING(LCDB_BST_SS_CTL, false, false), |
| SETTING(LCDB_LDO_VREG_OK_CTL, false, false), |
| }; |
| |
| /* For PMICs like pmi632/pm8150L */ |
| static struct settings lcdb_settings[] = { |
| SETTING(LCDB_BST_PD_CTL, false, true), |
| SETTING(LCDB_RDSON_MGMNT, false, false), |
| SETTING(LCDB_MISC_CTL, false, false), |
| SETTING(LCDB_SOFT_START_CTL, false, false), |
| SETTING(LCDB_PFM_CTL, false, false), |
| SETTING(LCDB_PWRUP_PWRDN_CTL, false, true), |
| SETTING(LCDB_LDO_PD_CTL, false, true), |
| SETTING(LCDB_LDO_SOFT_START_CTL, false, true), |
| SETTING(LCDB_NCP_PD_CTL, false, true), |
| SETTING(LCDB_NCP_SOFT_START_CTL, false, true), |
| SETTING(LCDB_BST_SS_CTL, false, true), |
| SETTING(LCDB_LDO_VREG_OK_CTL, false, true), |
| }; |
| |
| static int qpnp_lcdb_save_settings(struct qpnp_lcdb *lcdb) |
| { |
| int i, size, rc = 0; |
| struct settings *setting; |
| u16 pmic_subtype = lcdb->pmic_rev_id->pmic_subtype; |
| |
| if (pmic_subtype == PM660L_SUBTYPE) { |
| setting = lcdb_settings_pm660l; |
| size = ARRAY_SIZE(lcdb_settings_pm660l); |
| } else { |
| setting = lcdb_settings; |
| size = ARRAY_SIZE(lcdb_settings); |
| } |
| |
| for (i = 0; i < size; i++) { |
| if (setting[i].valid) { |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| setting[i].address, |
| &setting[i].value, 1); |
| if (rc < 0) { |
| pr_err("Failed to read lcdb register address=%x\n", |
| setting[i].address); |
| return rc; |
| } |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_restore_settings(struct qpnp_lcdb *lcdb) |
| { |
| int i, size, rc = 0; |
| struct settings *setting; |
| u16 pmic_subtype = lcdb->pmic_rev_id->pmic_subtype; |
| |
| if (pmic_subtype == PM660L_SUBTYPE) { |
| setting = lcdb_settings_pm660l; |
| size = ARRAY_SIZE(lcdb_settings_pm660l); |
| } else { |
| setting = lcdb_settings; |
| size = ARRAY_SIZE(lcdb_settings); |
| } |
| |
| for (i = 0; i < size; i++) { |
| if (setting[i].valid) { |
| if (setting[i].sec_access) |
| rc = qpnp_lcdb_secure_write(lcdb, lcdb->base + |
| setting[i].address, |
| setting[i].value); |
| else |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + |
| setting[i].address, |
| &setting[i].value, 1); |
| if (rc < 0) { |
| pr_err("Failed to write register address=%x\n", |
| setting[i].address); |
| return rc; |
| } |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_ttw_enter(struct qpnp_lcdb *lcdb) |
| { |
| int rc; |
| u8 val; |
| |
| if (!lcdb->settings_saved) { |
| rc = qpnp_lcdb_save_settings(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to save LCDB settings rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->settings_saved = true; |
| } |
| |
| val = (BST_SS_TIME_OVERRIDE_1MS << BST_SS_TIME_OVERRIDE_SHIFT) | |
| (DIS_BST_PRECHG_SHORT_ALARM << BST_PRECHG_SHORT_ALARM_SHIFT); |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_BST_SS_CTL_REG, &val, 1); |
| if (rc < 0) |
| return rc; |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_NCP_SOFT_START_CTL_REG, |
| &val, 1); |
| if (rc < 0) |
| return rc; |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_LDO_SOFT_START_CTL_REG, |
| &val, 1); |
| if (rc < 0) |
| return rc; |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_PWRUP_PWRDN_CTL_REG, |
| &val, 1); |
| if (rc < 0) |
| return rc; |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_BST_VREG_OK_CTL_REG, |
| &val, 1); |
| if (rc < 0) |
| return rc; |
| |
| val = BOOST_DIS_PULLDOWN_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_BST_PD_CTL_REG, |
| &val, 1); |
| if (rc < 0) |
| return rc; |
| |
| val = LDO_DIS_PULLDOWN_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_LDO_PD_CTL_REG, |
| &val, 1); |
| if (rc < 0) |
| return rc; |
| |
| val = NCP_DIS_PULLDOWN_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_NCP_PD_CTL_REG, |
| &val, 1); |
| if (rc < 0) |
| return rc; |
| |
| val = HWEN_RDY_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_ENABLE_CTL1_REG, |
| &val, 1); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ttw_enter_pm660l(struct qpnp_lcdb *lcdb) |
| { |
| int rc; |
| u8 val; |
| |
| if (!lcdb->settings_saved) { |
| rc = qpnp_lcdb_save_settings(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to save LCDB settings rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->settings_saved = true; |
| } |
| |
| val = BOOST_DIS_PULLDOWN_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_BST_PD_CTL_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set BST PD rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = (RDSON_HALF << NFET_SW_SIZE_SHIFT) | RDSON_HALF; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_RDSON_MGMNT_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set RDSON MGMT rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = AUTO_GM_EN_BIT | EN_TOUCH_WAKE_BIT | DIS_SCP_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_MISC_CTL_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set MISC CTL rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_SOFT_START_CTL_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set LCDB_SOFT_START rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = EN_PFM_BIT | (PFM_HYST_25MV << PFM_HYSTERESIS_SHIFT) | |
| (PFM_PEAK_CURRENT_400MA << PFM_CURRENT_SHIFT) | |
| BYP_BST_SOFT_START_COMP_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_PFM_CTL_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set PFM_CTL rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = 0; |
| rc = qpnp_lcdb_secure_write(lcdb, lcdb->base + LCDB_PWRUP_PWRDN_CTL_REG, |
| val); |
| if (rc < 0) { |
| pr_err("Failed to set PWRUP_PWRDN_CTL rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = LDO_DIS_PULLDOWN_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_LDO_PD_CTL_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set LDO_PD_CTL rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_LDO_SOFT_START_CTL_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set LDO_SOFT_START rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = NCP_DIS_PULLDOWN_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_NCP_PD_CTL_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set NCP_PD_CTL rc=%d\n", rc); |
| return rc; |
| } |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_NCP_SOFT_START_CTL_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to set NCP_SOFT_START rc=%d\n", rc); |
| return rc; |
| } |
| |
| if (lcdb->ttw_mode_sw) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_AUTO_TOUCH_WAKE_CTL_REG, |
| EN_AUTO_TOUCH_WAKE_BIT, |
| EN_AUTO_TOUCH_WAKE_BIT); |
| if (rc < 0) |
| pr_err("Failed to enable auto(sw) TTW\n rc = %d\n", rc); |
| } else { |
| val = HWEN_RDY_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_ENABLE_CTL1_REG, |
| &val, 1); |
| if (rc < 0) |
| pr_err("Failed to hw_enable lcdb rc= %d\n", rc); |
| } |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ttw_exit(struct qpnp_lcdb *lcdb) |
| { |
| int rc; |
| |
| if (lcdb->settings_saved) { |
| rc = qpnp_lcdb_restore_settings(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to restore lcdb settings rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->settings_saved = false; |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_enable_wa(struct qpnp_lcdb *lcdb) |
| { |
| int rc; |
| u8 val = 0; |
| |
| /* required only for PM660L */ |
| if (lcdb->pmic_rev_id->pmic_subtype != PM660L_SUBTYPE) |
| return 0; |
| |
| val = MODULE_EN_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_ENABLE_CTL1_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to enable lcdb rc= %d\n", rc); |
| return rc; |
| } |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_ENABLE_CTL1_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to disable lcdb rc= %d\n", rc); |
| return rc; |
| } |
| |
| if (lcdb->wa_flags & NCP_SCP_DISABLE_WA) { |
| /* |
| * delay to make sure that the MID pin – ie the |
| * output of the LCDB boost – returns to 0V |
| * after the module is disabled |
| */ |
| usleep_range(10000, 10100); |
| |
| rc = qpnp_lcdb_masked_write(lcdb, |
| lcdb->base + LCDB_MISC_CTL_REG, |
| DIS_SCP_BIT, DIS_SCP_BIT); |
| if (rc < 0) { |
| pr_err("Failed to disable SC rc=%d\n", rc); |
| return rc; |
| } |
| /* delay for SC-disable to take effect */ |
| usleep_range(1000, 1100); |
| |
| rc = qpnp_lcdb_masked_write(lcdb, |
| lcdb->base + LCDB_MISC_CTL_REG, |
| DIS_SCP_BIT, 0); |
| if (rc < 0) { |
| pr_err("Failed to enable SC rc=%d\n", rc); |
| return rc; |
| } |
| /* delay for SC-enable to take effect */ |
| usleep_range(1000, 1100); |
| } |
| |
| return 0; |
| } |
| |
| #define VOLTAGE_START_MV 4500 |
| #define VOLTAGE_STEP_MV 500 |
| |
| static int qpnp_lcdb_enable(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0, timeout, delay; |
| int voltage_mv = VOLTAGE_START_MV; |
| u8 val = 0; |
| |
| if (lcdb->lcdb_enabled || lcdb->lcdb_sc_disable) { |
| pr_debug("lcdb_enabled=%d lcdb_sc_disable=%d\n", |
| lcdb->lcdb_enabled, lcdb->lcdb_sc_disable); |
| return 0; |
| } |
| |
| if (lcdb->ttw_enable) { |
| rc = qpnp_lcdb_ttw_exit(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to exit TTW mode rc=%d\n", rc); |
| return rc; |
| } |
| } |
| |
| rc = qpnp_lcdb_enable_wa(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to execute enable_wa rc=%d\n", rc); |
| return rc; |
| } |
| |
| if (lcdb->voltage_step_ramp) { |
| if (lcdb->ldo.voltage_mv < VOLTAGE_START_MV) |
| voltage_mv = lcdb->ldo.voltage_mv; |
| |
| rc = qpnp_lcdb_set_voltage(lcdb, voltage_mv, LDO); |
| if (rc < 0) |
| return rc; |
| |
| if (lcdb->ncp.voltage_mv < VOLTAGE_START_MV) |
| voltage_mv = lcdb->ncp.voltage_mv; |
| |
| rc = qpnp_lcdb_set_voltage(lcdb, voltage_mv, NCP); |
| if (rc < 0) |
| return rc; |
| } |
| |
| val = MODULE_EN_BIT; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_ENABLE_CTL1_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to disable lcdb rc= %d\n", rc); |
| goto fail_enable; |
| } |
| |
| /* poll for vreg_ok */ |
| timeout = 10; |
| delay = lcdb->bst.soft_start_us + lcdb->ldo.soft_start_us + |
| lcdb->ncp.soft_start_us; |
| delay += lcdb->bst.vreg_ok_dbc_us + lcdb->ldo.vreg_ok_dbc_us + |
| lcdb->ncp.vreg_ok_dbc_us; |
| while (timeout--) { |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + INT_RT_STATUS_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to poll for vreg-ok status rc=%d\n", rc); |
| break; |
| } |
| if (val & VREG_OK_RT_STS_BIT) |
| break; |
| |
| usleep_range(delay, delay + 100); |
| } |
| |
| if (rc || !timeout) { |
| if (!timeout) { |
| pr_err("lcdb-vreg-ok status failed to change\n"); |
| rc = -ETIMEDOUT; |
| } |
| goto fail_enable; |
| } |
| |
| lcdb->lcdb_enabled = true; |
| if (lcdb->voltage_step_ramp) { |
| usleep_range(10000, 11000); |
| rc = qpnp_lcdb_set_voltage_step(lcdb, |
| voltage_mv + VOLTAGE_STEP_MV, |
| LDO_NCP); |
| if (rc < 0) { |
| pr_err("Failed to set LCDB voltage rc=%d\n", rc); |
| return rc; |
| } |
| } |
| |
| pr_debug("lcdb enabled successfully!\n"); |
| |
| return 0; |
| |
| fail_enable: |
| dump_status_registers(lcdb); |
| pr_err("Failed to enable lcdb rc=%d\n", rc); |
| return rc; |
| } |
| |
| static int qpnp_lcdb_disable(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| u8 val; |
| u16 pmic_subtype = lcdb->pmic_rev_id->pmic_subtype; |
| |
| if (!lcdb->lcdb_enabled) |
| return 0; |
| |
| if (lcdb->ttw_enable) { |
| if (pmic_subtype == PM660L_SUBTYPE) |
| rc = qpnp_lcdb_ttw_enter_pm660l(lcdb); |
| else |
| rc = qpnp_lcdb_ttw_enter(lcdb); |
| |
| if (rc < 0) { |
| pr_err("Failed to enable TTW mode rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->lcdb_enabled = false; |
| |
| return 0; |
| } |
| |
| if (lcdb->wa_flags & FORCE_PD_ENABLE_WA) { |
| /* |
| * force pull-down to enable quick discharge after |
| * turning off |
| */ |
| val = LDO_FORCE_PD_EN_BIT | LDO_FORCE_PD_MODE; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + |
| LCDB_LDO_FORCE_PD_CTL_REG, &val, 1); |
| if (rc < 0) |
| return rc; |
| } |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + LCDB_ENABLE_CTL1_REG, |
| &val, 1); |
| if (rc < 0) |
| pr_err("Failed to disable lcdb rc= %d\n", rc); |
| else |
| lcdb->lcdb_enabled = false; |
| |
| if (lcdb->wa_flags & FORCE_PD_ENABLE_WA) { |
| /* wait for 10 msec after module disable for LDO to discharge */ |
| usleep_range(10000, 11000); |
| |
| val = 0; |
| rc = qpnp_lcdb_write(lcdb, lcdb->base + |
| LCDB_LDO_FORCE_PD_CTL_REG, &val, 1); |
| if (rc < 0) |
| return rc; |
| } |
| |
| return rc; |
| } |
| |
| #define LCDB_SC_RESET_CNT_DLY_US 1000000 |
| #define LCDB_SC_CNT_MAX 10 |
| static int qpnp_lcdb_handle_sc_event(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| s64 elapsed_time_us; |
| |
| mutex_lock(&lcdb->lcdb_mutex); |
| rc = qpnp_lcdb_disable(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to disable lcdb rc=%d\n", rc); |
| goto unlock_mutex; |
| } |
| |
| /* Check if the SC re-occurred immediately */ |
| elapsed_time_us = ktime_us_delta(ktime_get(), |
| lcdb->sc_module_enable_time); |
| if (elapsed_time_us > LCDB_SC_RESET_CNT_DLY_US) { |
| lcdb->sc_count = 0; |
| } else if (lcdb->sc_count > LCDB_SC_CNT_MAX) { |
| pr_err("SC trigged %d times, disabling LCDB forever!\n", |
| lcdb->sc_count); |
| lcdb->lcdb_sc_disable = true; |
| goto unlock_mutex; |
| } |
| lcdb->sc_count++; |
| lcdb->sc_module_enable_time = ktime_get(); |
| |
| /* delay for SC to clear */ |
| usleep_range(10000, 10100); |
| |
| rc = qpnp_lcdb_enable(lcdb); |
| if (rc < 0) |
| pr_err("Failed to enable lcdb rc=%d\n", rc); |
| |
| unlock_mutex: |
| mutex_unlock(&lcdb->lcdb_mutex); |
| return rc; |
| } |
| |
| static irqreturn_t qpnp_lcdb_sc_irq_handler(int irq, void *data) |
| { |
| struct qpnp_lcdb *lcdb = data; |
| int rc; |
| u8 val, val2[2] = {0}; |
| |
| mutex_lock(&lcdb->lcdb_mutex); |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + INT_RT_STATUS_REG, &val, 1); |
| mutex_unlock(&lcdb->lcdb_mutex); |
| if (rc < 0) |
| goto irq_handled; |
| |
| if (val & SC_ERROR_RT_STS_BIT) { |
| rc = qpnp_lcdb_read(lcdb, |
| lcdb->base + LCDB_MISC_CTL_REG, &val, 1); |
| if (rc < 0) |
| goto irq_handled; |
| |
| if (val & EN_TOUCH_WAKE_BIT) { |
| /* blanking time */ |
| usleep_range(300, 310); |
| /* |
| * The status registers need to written with any value |
| * before reading |
| */ |
| rc = qpnp_lcdb_write(lcdb, |
| lcdb->base + LCDB_STS3_REG, val2, 2); |
| if (rc < 0) |
| goto irq_handled; |
| |
| rc = qpnp_lcdb_read(lcdb, |
| lcdb->base + LCDB_STS3_REG, val2, 2); |
| if (rc < 0) |
| goto irq_handled; |
| |
| if (!(val2[0] & LDO_VREG_OK_BIT) || |
| !(val2[1] & NCP_VREG_OK_BIT)) { |
| rc = qpnp_lcdb_handle_sc_event(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to handle SC rc=%d\n", |
| rc); |
| goto irq_handled; |
| } |
| } |
| } else { |
| /* blanking time */ |
| usleep_range(2000, 2100); |
| /* Read the SC status again to confirm true SC */ |
| mutex_lock(&lcdb->lcdb_mutex); |
| /* |
| * Wait for the completion of LCDB module enable, |
| * which could be initiated in a previous SC event, |
| * to avoid multiple module disable/enable calls. |
| */ |
| rc = qpnp_lcdb_read(lcdb, |
| lcdb->base + INT_RT_STATUS_REG, &val, 1); |
| mutex_unlock(&lcdb->lcdb_mutex); |
| if (rc < 0) |
| goto irq_handled; |
| |
| if (val & SC_ERROR_RT_STS_BIT) { |
| rc = qpnp_lcdb_handle_sc_event(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to handle SC rc=%d\n", |
| rc); |
| goto irq_handled; |
| } |
| } |
| } |
| } |
| irq_handled: |
| return IRQ_HANDLED; |
| } |
| |
| #define MIN_BST_VOLTAGE_MV 4700 |
| #define PM660_MAX_BST_VOLTAGE_MV 6250 |
| #define MAX_BST_VOLTAGE_MV 6275 |
| #define MIN_VOLTAGE_MV 4000 |
| #define MAX_VOLTAGE_MV 6000 |
| #define VOLTAGE_MIN_STEP_100_MV 4000 |
| #define VOLTAGE_MIN_STEP_50_MV 4950 |
| #define VOLTAGE_STEP_100_MV 100 |
| #define VOLTAGE_STEP_50_MV 50 |
| #define VOLTAGE_STEP_25_MV 25 |
| #define VOLTAGE_STEP_50MV_OFFSET 0xA |
| static int qpnp_lcdb_set_bst_voltage(struct qpnp_lcdb *lcdb, |
| int voltage_mv, u8 type) |
| { |
| int rc = 0; |
| u8 val, voltage_step, mask = 0; |
| int bst_voltage_mv; |
| u16 pmic_subtype = lcdb->pmic_rev_id->pmic_subtype; |
| struct ldo_regulator *ldo = &lcdb->ldo; |
| struct ncp_regulator *ncp = &lcdb->ncp; |
| struct bst_params *bst = &lcdb->bst; |
| |
| /* Vout_Boost = headroom_mv + max( Vout_LDO, abs (Vout_NCP)) */ |
| bst_voltage_mv = max(voltage_mv, max(ldo->voltage_mv, ncp->voltage_mv)); |
| bst_voltage_mv += bst->headroom_mv; |
| |
| if (bst_voltage_mv < MIN_BST_VOLTAGE_MV) |
| bst_voltage_mv = MIN_BST_VOLTAGE_MV; |
| |
| if (pmic_subtype == PM660L_SUBTYPE) { |
| if (bst_voltage_mv > PM660_MAX_BST_VOLTAGE_MV) |
| bst_voltage_mv = PM660_MAX_BST_VOLTAGE_MV; |
| } else { |
| if (bst_voltage_mv > MAX_BST_VOLTAGE_MV) |
| bst_voltage_mv = MAX_BST_VOLTAGE_MV; |
| } |
| |
| if (bst_voltage_mv != bst->voltage_mv) { |
| if (pmic_subtype == PM660L_SUBTYPE) { |
| mask = PM660_BST_OUTPUT_VOLTAGE_MASK; |
| voltage_step = VOLTAGE_STEP_50_MV; |
| } else { |
| mask = BST_OUTPUT_VOLTAGE_MASK; |
| voltage_step = VOLTAGE_STEP_25_MV; |
| } |
| |
| val = DIV_ROUND_UP(bst_voltage_mv - MIN_BST_VOLTAGE_MV, |
| voltage_step); |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_BST_OUTPUT_VOLTAGE_REG, |
| mask, val); |
| if (rc < 0) { |
| pr_err("Failed to set boost voltage %d mv rc=%d\n", |
| bst_voltage_mv, rc); |
| } else { |
| pr_debug("Boost voltage set = %d mv (0x%02x = 0x%02x)\n", |
| bst_voltage_mv, LCDB_BST_OUTPUT_VOLTAGE_REG, val); |
| bst->voltage_mv = bst_voltage_mv; |
| } |
| } |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_get_bst_voltage(struct qpnp_lcdb *lcdb, |
| int *voltage_mv) |
| { |
| int rc; |
| u8 val, voltage_step, mask = 0; |
| u16 pmic_subtype = lcdb->pmic_rev_id->pmic_subtype; |
| |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + LCDB_BST_OUTPUT_VOLTAGE_REG, |
| &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to reat BST voltage rc=%d\n", rc); |
| return rc; |
| } |
| |
| if (pmic_subtype == PM660L_SUBTYPE) { |
| mask = PM660_BST_OUTPUT_VOLTAGE_MASK; |
| voltage_step = VOLTAGE_STEP_50_MV; |
| } else { |
| mask = BST_OUTPUT_VOLTAGE_MASK; |
| voltage_step = VOLTAGE_STEP_25_MV; |
| } |
| |
| val &= mask; |
| *voltage_mv = (val * voltage_step) + MIN_BST_VOLTAGE_MV; |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_set_voltage(struct qpnp_lcdb *lcdb, |
| int voltage_mv, u8 type) |
| { |
| int rc = 0; |
| u16 offset = LCDB_LDO_OUTPUT_VOLTAGE_REG; |
| u8 val = 0; |
| |
| if (!is_between(voltage_mv, MIN_VOLTAGE_MV, MAX_VOLTAGE_MV)) { |
| pr_err("Invalid voltage %dmv (min=%d max=%d)\n", |
| voltage_mv, MIN_VOLTAGE_MV, MAX_VOLTAGE_MV); |
| return -EINVAL; |
| } |
| |
| rc = qpnp_lcdb_set_bst_voltage(lcdb, voltage_mv, type); |
| if (rc < 0) { |
| pr_err("Failed to set boost voltage rc=%d\n", rc); |
| return rc; |
| } |
| |
| /* Below logic is only valid for LDO and NCP type */ |
| if (voltage_mv < VOLTAGE_MIN_STEP_50_MV) { |
| val = DIV_ROUND_UP(voltage_mv - VOLTAGE_MIN_STEP_100_MV, |
| VOLTAGE_STEP_100_MV); |
| } else { |
| val = DIV_ROUND_UP(voltage_mv - VOLTAGE_MIN_STEP_50_MV, |
| VOLTAGE_STEP_50_MV); |
| val += VOLTAGE_STEP_50MV_OFFSET; |
| } |
| |
| if (type == NCP) |
| offset = LCDB_NCP_OUTPUT_VOLTAGE_REG; |
| |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + offset, |
| SET_OUTPUT_VOLTAGE_MASK, val); |
| if (rc < 0) |
| pr_err("Failed to set output voltage %d mv for %s rc=%d\n", |
| voltage_mv, (type == LDO) ? "LDO" : "NCP", rc); |
| else |
| pr_debug("%s voltage set = %d mv (0x%02x = 0x%02x)\n", |
| (type == LDO) ? "LDO" : "NCP", voltage_mv, offset, val); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_set_voltage_step(struct qpnp_lcdb *lcdb, |
| int voltage_start_mv, u8 type) |
| { |
| int i, ldo_voltage, ncp_voltage, voltage, rc = 0; |
| |
| for (i = voltage_start_mv; i <= (MAX_VOLTAGE_MV + VOLTAGE_STEP_MV); |
| i += VOLTAGE_STEP_MV) { |
| |
| ldo_voltage = (lcdb->ldo.voltage_mv < i) ? |
| lcdb->ldo.voltage_mv : i; |
| |
| ncp_voltage = (lcdb->ncp.voltage_mv < i) ? |
| lcdb->ncp.voltage_mv : i; |
| if (type == LDO_NCP) { |
| rc = qpnp_lcdb_set_voltage(lcdb, ldo_voltage, LDO); |
| if (rc < 0) |
| return rc; |
| |
| rc = qpnp_lcdb_set_voltage(lcdb, ncp_voltage, NCP); |
| if (rc < 0) |
| return rc; |
| |
| pr_debug(" LDO voltage step %d NCP voltage step %d\n", |
| ldo_voltage, ncp_voltage); |
| |
| if ((i >= lcdb->ncp.voltage_mv) && |
| (i >= lcdb->ldo.voltage_mv)) |
| break; |
| } else { |
| voltage = (type == LDO) ? ldo_voltage : ncp_voltage; |
| rc = qpnp_lcdb_set_voltage(lcdb, voltage, type); |
| if (rc < 0) |
| return rc; |
| |
| pr_debug("%s voltage step %d\n", |
| (type == LDO) ? "LDO" : "NCP", voltage); |
| if ((type == LDO) && (i >= lcdb->ldo.voltage_mv)) |
| break; |
| |
| if ((type == NCP) && (i >= lcdb->ncp.voltage_mv)) |
| break; |
| |
| } |
| |
| usleep_range(1000, 1100); |
| } |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_get_voltage(struct qpnp_lcdb *lcdb, |
| u32 *voltage_mv, u8 type) |
| { |
| int rc = 0; |
| u16 offset = LCDB_LDO_OUTPUT_VOLTAGE_REG; |
| u8 val = 0; |
| |
| if (type == BST) |
| return qpnp_lcdb_get_bst_voltage(lcdb, voltage_mv); |
| |
| if (type == NCP) |
| offset = LCDB_NCP_OUTPUT_VOLTAGE_REG; |
| |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + offset, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read %s volatge rc=%d\n", |
| (type == LDO) ? "LDO" : "NCP", rc); |
| return rc; |
| } |
| |
| val &= SET_OUTPUT_VOLTAGE_MASK; |
| if (val < VOLTAGE_STEP_50MV_OFFSET) { |
| *voltage_mv = VOLTAGE_MIN_STEP_100_MV + |
| (val * VOLTAGE_STEP_100_MV); |
| } else { |
| *voltage_mv = VOLTAGE_MIN_STEP_50_MV + |
| ((val - VOLTAGE_STEP_50MV_OFFSET) * VOLTAGE_STEP_50_MV); |
| } |
| |
| if (!rc) |
| pr_debug("%s voltage read-back = %d mv (0x%02x = 0x%02x)\n", |
| (type == LDO) ? "LDO" : "NCP", |
| *voltage_mv, offset, val); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_set_soft_start(struct qpnp_lcdb *lcdb, |
| u32 ss_us, u8 type) |
| { |
| int rc = 0, i = 0; |
| u16 offset = LCDB_LDO_SOFT_START_CTL_REG; |
| u8 val = 0; |
| |
| if (type == NCP) |
| offset = LCDB_NCP_SOFT_START_CTL_REG; |
| |
| if (!is_between(ss_us, MIN_SOFT_START_US, MAX_SOFT_START_US)) { |
| pr_err("Invalid soft_start_us %d (min=%d max=%d)\n", |
| ss_us, MIN_SOFT_START_US, MAX_SOFT_START_US); |
| return -EINVAL; |
| } |
| |
| i = 0; |
| while (ss_us > soft_start_us[i]) |
| i++; |
| val = ((i == 0) ? 0 : i - 1) & SOFT_START_MASK; |
| |
| rc = qpnp_lcdb_masked_write(lcdb, |
| lcdb->base + offset, SOFT_START_MASK, val); |
| if (rc < 0) |
| pr_err("Failed to write %s soft-start time %d rc=%d\n", |
| (type == LDO) ? "LDO" : "NCP", soft_start_us[i], rc); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ldo_regulator_enable(struct regulator_dev *rdev) |
| { |
| int rc = 0; |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| if (lcdb->secure_mode) |
| return 0; |
| |
| mutex_lock(&lcdb->lcdb_mutex); |
| rc = qpnp_lcdb_enable(lcdb); |
| if (rc < 0) |
| pr_err("Failed to enable lcdb rc=%d\n", rc); |
| mutex_unlock(&lcdb->lcdb_mutex); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ldo_regulator_disable(struct regulator_dev *rdev) |
| { |
| int rc = 0; |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| if (lcdb->secure_mode) |
| return 0; |
| |
| mutex_lock(&lcdb->lcdb_mutex); |
| rc = qpnp_lcdb_disable(lcdb); |
| if (rc < 0) |
| pr_err("Failed to disable lcdb rc=%d\n", rc); |
| mutex_unlock(&lcdb->lcdb_mutex); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ldo_regulator_is_enabled(struct regulator_dev *rdev) |
| { |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| return lcdb->lcdb_enabled; |
| } |
| |
| static int qpnp_lcdb_ldo_regulator_set_voltage(struct regulator_dev *rdev, |
| int min_uV, int max_uV, unsigned int *selector) |
| { |
| int rc = 0; |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| if (lcdb->secure_mode) |
| return 0; |
| |
| lcdb->ldo.voltage_mv = min_uV / 1000; |
| if (lcdb->voltage_step_ramp) |
| rc = qpnp_lcdb_set_voltage_step(lcdb, |
| lcdb->ldo.prev_voltage_mv + VOLTAGE_STEP_MV, LDO); |
| else |
| rc = qpnp_lcdb_set_voltage(lcdb, lcdb->ldo.voltage_mv, LDO); |
| |
| if (rc < 0) |
| pr_err("Failed to set LDO voltage rc=%c\n", rc); |
| else |
| lcdb->ldo.prev_voltage_mv = lcdb->ldo.voltage_mv; |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ldo_regulator_get_voltage(struct regulator_dev *rdev) |
| { |
| int rc = 0; |
| u32 voltage_mv = 0; |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| rc = qpnp_lcdb_get_voltage(lcdb, &voltage_mv, LDO); |
| if (rc < 0) { |
| pr_err("Failed to get ldo voltage rc=%d\n", rc); |
| return rc; |
| } |
| |
| return voltage_mv * 1000; |
| } |
| |
| static struct regulator_ops qpnp_lcdb_ldo_ops = { |
| .enable = qpnp_lcdb_ldo_regulator_enable, |
| .disable = qpnp_lcdb_ldo_regulator_disable, |
| .is_enabled = qpnp_lcdb_ldo_regulator_is_enabled, |
| .set_voltage = qpnp_lcdb_ldo_regulator_set_voltage, |
| .get_voltage = qpnp_lcdb_ldo_regulator_get_voltage, |
| }; |
| |
| static int qpnp_lcdb_ncp_regulator_enable(struct regulator_dev *rdev) |
| { |
| int rc = 0; |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| if (lcdb->secure_mode) |
| return 0; |
| |
| mutex_lock(&lcdb->lcdb_mutex); |
| rc = qpnp_lcdb_enable(lcdb); |
| if (rc < 0) |
| pr_err("Failed to enable lcdb rc=%d\n", rc); |
| mutex_unlock(&lcdb->lcdb_mutex); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ncp_regulator_disable(struct regulator_dev *rdev) |
| { |
| int rc = 0; |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| if (lcdb->secure_mode) |
| return 0; |
| |
| mutex_lock(&lcdb->lcdb_mutex); |
| rc = qpnp_lcdb_disable(lcdb); |
| if (rc < 0) |
| pr_err("Failed to disable lcdb rc=%d\n", rc); |
| mutex_unlock(&lcdb->lcdb_mutex); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ncp_regulator_is_enabled(struct regulator_dev *rdev) |
| { |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| return lcdb->lcdb_enabled; |
| } |
| |
| static int qpnp_lcdb_ncp_regulator_set_voltage(struct regulator_dev *rdev, |
| int min_uV, int max_uV, unsigned int *selector) |
| { |
| int rc = 0; |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| if (lcdb->secure_mode) |
| return 0; |
| |
| lcdb->ncp.voltage_mv = min_uV / 1000; |
| if (lcdb->voltage_step_ramp) |
| rc = qpnp_lcdb_set_voltage_step(lcdb, |
| lcdb->ncp.prev_voltage_mv + VOLTAGE_STEP_MV, NCP); |
| else |
| rc = qpnp_lcdb_set_voltage(lcdb, lcdb->ncp.voltage_mv, NCP); |
| |
| if (rc < 0) |
| pr_err("Failed to set NCP voltage rc=%c\n", rc); |
| else |
| lcdb->ncp.prev_voltage_mv = lcdb->ncp.voltage_mv; |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_ncp_regulator_get_voltage(struct regulator_dev *rdev) |
| { |
| int rc; |
| u32 voltage_mv = 0; |
| struct qpnp_lcdb *lcdb = rdev_get_drvdata(rdev); |
| |
| rc = qpnp_lcdb_get_voltage(lcdb, &voltage_mv, NCP); |
| if (rc < 0) { |
| pr_err("Failed to get ncp voltage rc=%d\n", rc); |
| return rc; |
| } |
| |
| return voltage_mv * 1000; |
| } |
| |
| static struct regulator_ops qpnp_lcdb_ncp_ops = { |
| .enable = qpnp_lcdb_ncp_regulator_enable, |
| .disable = qpnp_lcdb_ncp_regulator_disable, |
| .is_enabled = qpnp_lcdb_ncp_regulator_is_enabled, |
| .set_voltage = qpnp_lcdb_ncp_regulator_set_voltage, |
| .get_voltage = qpnp_lcdb_ncp_regulator_get_voltage, |
| }; |
| |
| static int qpnp_lcdb_regulator_register(struct qpnp_lcdb *lcdb, u8 type) |
| { |
| int rc = 0, off_on_delay = 0, voltage_step = VOLTAGE_STEP_50_MV; |
| struct regulator_init_data *init_data; |
| struct regulator_config cfg = {}; |
| struct regulator_desc *rdesc; |
| struct regulator_dev *rdev; |
| struct device_node *node; |
| |
| if (lcdb->pmic_rev_id->pmic_subtype != PM660L_SUBTYPE) |
| off_on_delay = PMIC5_LCDB_OFF_ON_DELAY_US; |
| |
| if (type == LDO) { |
| node = lcdb->ldo.node; |
| rdesc = &lcdb->ldo.rdesc; |
| rdesc->ops = &qpnp_lcdb_ldo_ops; |
| rdesc->off_on_delay = off_on_delay; |
| rdesc->n_voltages = ((MAX_VOLTAGE_MV - MIN_VOLTAGE_MV) |
| / voltage_step) + 1; |
| rdev = lcdb->ldo.rdev; |
| } else if (type == NCP) { |
| node = lcdb->ncp.node; |
| rdesc = &lcdb->ncp.rdesc; |
| rdesc->ops = &qpnp_lcdb_ncp_ops; |
| rdesc->off_on_delay = off_on_delay; |
| rdesc->n_voltages = ((MAX_VOLTAGE_MV - MIN_VOLTAGE_MV) |
| / voltage_step) + 1; |
| rdev = lcdb->ncp.rdev; |
| } else { |
| pr_err("Invalid regulator type %d\n", type); |
| return -EINVAL; |
| } |
| |
| init_data = of_get_regulator_init_data(lcdb->dev, node, rdesc); |
| if (!init_data) { |
| pr_err("Failed to get regulator_init_data for %s\n", |
| (type == LDO) ? "LDO" : "NCP"); |
| return -ENOMEM; |
| } |
| |
| if (init_data->constraints.name) { |
| rdesc->owner = THIS_MODULE; |
| rdesc->type = REGULATOR_VOLTAGE; |
| rdesc->name = init_data->constraints.name; |
| |
| cfg.dev = lcdb->dev; |
| cfg.init_data = init_data; |
| cfg.driver_data = lcdb; |
| cfg.of_node = node; |
| |
| if (of_get_property(lcdb->dev->of_node, "parent-supply", NULL)) |
| init_data->supply_regulator = "parent"; |
| |
| init_data->constraints.valid_ops_mask |
| |= REGULATOR_CHANGE_VOLTAGE |
| | REGULATOR_CHANGE_STATUS; |
| |
| rdev = devm_regulator_register(lcdb->dev, rdesc, &cfg); |
| if (IS_ERR(rdev)) { |
| rc = PTR_ERR(rdev); |
| rdev = NULL; |
| pr_err("Failed to register lcdb_%s regulator rc = %d\n", |
| (type == LDO) ? "LDO" : "NCP", rc); |
| return rc; |
| } |
| } else { |
| pr_err("%s_regulator name missing\n", |
| (type == LDO) ? "LDO" : "NCP"); |
| return -EINVAL; |
| } |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_parse_ttw(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| u32 temp; |
| u8 val = 0; |
| struct device_node *node = lcdb->dev->of_node; |
| |
| if (of_property_read_bool(node, "qcom,ttw-mode-sw")) { |
| lcdb->ttw_mode_sw = true; |
| rc = of_property_read_u32(node, "qcom,attw-toff-ms", &temp); |
| if (!rc) { |
| if (!is_between(temp, ATTW_MIN_MS, ATTW_MAX_MS)) { |
| pr_err("Invalid TOFF val %d (min=%d max=%d)\n", |
| temp, ATTW_MIN_MS, ATTW_MAX_MS); |
| return -EINVAL; |
| } |
| val = ilog2(temp / 4) << ATTW_TOFF_TIME_SHIFT; |
| } else { |
| pr_err("qcom,attw-toff-ms not specified for TTW SW mode\n"); |
| return rc; |
| } |
| |
| rc = of_property_read_u32(node, "qcom,attw-ton-ms", &temp); |
| if (!rc) { |
| if (!is_between(temp, ATTW_MIN_MS, ATTW_MAX_MS)) { |
| pr_err("Invalid TON value %d (min=%d max=%d)\n", |
| temp, ATTW_MIN_MS, ATTW_MAX_MS); |
| return -EINVAL; |
| } |
| val |= ilog2(temp / 4); |
| } else { |
| pr_err("qcom,attw-ton-ms not specified for TTW SW mode\n"); |
| return rc; |
| } |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_AUTO_TOUCH_WAKE_CTL_REG, |
| ATTW_TON_TIME_MASK | ATTW_TOFF_TIME_MASK, val); |
| if (rc < 0) { |
| pr_err("Failed to write ATTW ON/OFF rc=%d\n", rc); |
| return rc; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_ldo_dt_init(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| struct device_node *node = lcdb->ldo.node; |
| |
| /* LDO output voltage */ |
| lcdb->ldo.voltage_mv = -EINVAL; |
| rc = of_property_read_u32(node, "qcom,ldo-voltage-mv", |
| &lcdb->ldo.voltage_mv); |
| if (!rc && !is_between(lcdb->ldo.voltage_mv, MIN_VOLTAGE_MV, |
| MAX_VOLTAGE_MV)) { |
| pr_err("Invalid LDO voltage %dmv (min=%d max=%d)\n", |
| lcdb->ldo.voltage_mv, MIN_VOLTAGE_MV, MAX_VOLTAGE_MV); |
| return -EINVAL; |
| } |
| |
| /* LDO PD configuration */ |
| lcdb->ldo.pd = -EINVAL; |
| of_property_read_u32(node, "qcom,ldo-pd", &lcdb->ldo.pd); |
| |
| lcdb->ldo.pd_strength = -EINVAL; |
| of_property_read_u32(node, "qcom,ldo-pd-strength", |
| &lcdb->ldo.pd_strength); |
| |
| /* LDO ILIM configuration */ |
| lcdb->ldo.ilim_ma = -EINVAL; |
| rc = of_property_read_u32(node, "qcom,ldo-ilim-ma", &lcdb->ldo.ilim_ma); |
| if (!rc && !is_between(lcdb->ldo.ilim_ma, MIN_LDO_ILIM_MA, |
| MAX_LDO_ILIM_MA)) { |
| pr_err("Invalid ilim_ma %d (min=%d, max=%d)\n", |
| lcdb->ldo.ilim_ma, MIN_LDO_ILIM_MA, |
| MAX_LDO_ILIM_MA); |
| return -EINVAL; |
| } |
| |
| /* LDO soft-start (SS) configuration */ |
| lcdb->ldo.soft_start_us = -EINVAL; |
| of_property_read_u32(node, "qcom,ldo-soft-start-us", |
| &lcdb->ldo.soft_start_us); |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_ncp_dt_init(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| struct device_node *node = lcdb->ncp.node; |
| |
| /* NCP output voltage */ |
| lcdb->ncp.voltage_mv = -EINVAL; |
| rc = of_property_read_u32(node, "qcom,ncp-voltage-mv", |
| &lcdb->ncp.voltage_mv); |
| if (!rc && !is_between(lcdb->ncp.voltage_mv, MIN_VOLTAGE_MV, |
| MAX_VOLTAGE_MV)) { |
| pr_err("Invalid NCP voltage %dmv (min=%d max=%d)\n", |
| lcdb->ldo.voltage_mv, MIN_VOLTAGE_MV, MAX_VOLTAGE_MV); |
| return -EINVAL; |
| } |
| |
| /* NCP PD configuration */ |
| lcdb->ncp.pd = -EINVAL; |
| of_property_read_u32(node, "qcom,ncp-pd", &lcdb->ncp.pd); |
| |
| lcdb->ncp.pd_strength = -EINVAL; |
| of_property_read_u32(node, "qcom,ncp-pd-strength", |
| &lcdb->ncp.pd_strength); |
| |
| /* NCP ILIM configuration */ |
| lcdb->ncp.ilim_ma = -EINVAL; |
| rc = of_property_read_u32(node, "qcom,ncp-ilim-ma", &lcdb->ncp.ilim_ma); |
| if (!rc && !is_between(lcdb->ncp.ilim_ma, MIN_NCP_ILIM_MA, |
| MAX_NCP_ILIM_MA)) { |
| pr_err("Invalid ilim_ma %d (min=%d, max=%d)\n", |
| lcdb->ncp.ilim_ma, MIN_NCP_ILIM_MA, MAX_NCP_ILIM_MA); |
| return -EINVAL; |
| } |
| |
| /* NCP soft-start (SS) configuration */ |
| lcdb->ncp.soft_start_us = -EINVAL; |
| of_property_read_u32(node, "qcom,ncp-soft-start-us", |
| &lcdb->ncp.soft_start_us); |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_bst_dt_init(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| struct device_node *node = lcdb->bst.node; |
| u16 pmic_subtype = lcdb->pmic_rev_id->pmic_subtype; |
| u16 default_headroom_mv; |
| |
| /* Boost PD configuration */ |
| lcdb->bst.pd = -EINVAL; |
| of_property_read_u32(node, "qcom,bst-pd", &lcdb->bst.pd); |
| |
| lcdb->bst.pd_strength = -EINVAL; |
| of_property_read_u32(node, "qcom,bst-pd-strength", |
| &lcdb->bst.pd_strength); |
| |
| /* Boost ILIM */ |
| lcdb->bst.ilim_ma = -EINVAL; |
| rc = of_property_read_u32(node, "qcom,bst-ilim-ma", &lcdb->bst.ilim_ma); |
| if (!rc && !is_between(lcdb->bst.ilim_ma, MIN_BST_ILIM_MA, |
| MAX_BST_ILIM_MA)) { |
| pr_err("Invalid ilim_ma %d (min=%d, max=%d)\n", |
| lcdb->bst.ilim_ma, MIN_BST_ILIM_MA, MAX_BST_ILIM_MA); |
| return -EINVAL; |
| } |
| |
| /* Boost PS configuration */ |
| lcdb->bst.ps = -EINVAL; |
| of_property_read_u32(node, "qcom,bst-ps", &lcdb->bst.ps); |
| |
| lcdb->bst.ps_threshold = -EINVAL; |
| rc = of_property_read_u32(node, "qcom,bst-ps-threshold-ma", |
| &lcdb->bst.ps_threshold); |
| if (!rc && !is_between(lcdb->bst.ps_threshold, |
| MIN_BST_PS_MA, MAX_BST_PS_MA)) { |
| pr_err("Invalid bst ps_threshold %d (min=%d, max=%d)\n", |
| lcdb->bst.ps_threshold, MIN_BST_PS_MA, MAX_BST_PS_MA); |
| return -EINVAL; |
| } |
| |
| default_headroom_mv = (pmic_subtype == PM660L_SUBTYPE) ? |
| PM660_BST_HEADROOM_DEFAULT_MV : |
| BST_HEADROOM_DEFAULT_MV; |
| /* Boost head room configuration */ |
| of_property_read_u16(node, "qcom,bst-headroom-mv", |
| &lcdb->bst.headroom_mv); |
| if (lcdb->bst.headroom_mv < default_headroom_mv) |
| lcdb->bst.headroom_mv = default_headroom_mv; |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_init_ldo(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0, ilim_ma; |
| u8 val = 0; |
| |
| /* configure parameters only if LCDB is disabled */ |
| if (!is_lcdb_enabled(lcdb)) { |
| if (lcdb->ldo.voltage_mv != -EINVAL) { |
| rc = qpnp_lcdb_set_voltage(lcdb, |
| lcdb->ldo.voltage_mv, LDO); |
| if (rc < 0) { |
| pr_err("Failed to set voltage rc=%d\n", rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->ldo.pd != -EINVAL) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_LDO_PD_CTL_REG, LDO_DIS_PULLDOWN_BIT, |
| lcdb->ldo.pd ? 0 : LDO_DIS_PULLDOWN_BIT); |
| if (rc < 0) { |
| pr_err("Failed to configure LDO PD rc=%d\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->ldo.pd_strength != -EINVAL) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_LDO_PD_CTL_REG, LDO_PD_STRENGTH_BIT, |
| lcdb->ldo.pd_strength ? |
| LDO_PD_STRENGTH_BIT : 0); |
| if (rc < 0) { |
| pr_err("Failed to configure LDO PD strength %s rc=%d\n", |
| lcdb->ldo.pd_strength ? |
| "(strong)" : "(weak)", rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->ldo.ilim_ma != -EINVAL) { |
| ilim_ma = lcdb->ldo.ilim_ma - MIN_LDO_ILIM_MA; |
| ilim_ma /= LDO_ILIM_STEP_MA; |
| val = (ilim_ma & SET_LDO_ILIM_MASK) | EN_LDO_ILIM_BIT; |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_LDO_ILIM_CTL1_REG, |
| SET_LDO_ILIM_MASK | EN_LDO_ILIM_BIT, |
| val); |
| if (rc < 0) { |
| pr_err("Failed to configure LDO ilim_ma (CTL1=%d) rc=%d\n", |
| val, rc); |
| return rc; |
| } |
| |
| val = ilim_ma & SET_LDO_ILIM_MASK; |
| rc = qpnp_lcdb_masked_write(lcdb, |
| lcdb->base + LCDB_LDO_ILIM_CTL2_REG, |
| SET_LDO_ILIM_MASK, val); |
| if (rc < 0) { |
| pr_err("Failed to configure LDO ilim_ma (CTL2=%d) rc=%d\n", |
| val, rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->ldo.soft_start_us != -EINVAL) { |
| rc = qpnp_lcdb_set_soft_start(lcdb, |
| lcdb->ldo.soft_start_us, LDO); |
| if (rc < 0) { |
| pr_err("Failed to set LDO soft_start rc=%d\n", |
| rc); |
| return rc; |
| } |
| } |
| } |
| |
| rc = qpnp_lcdb_get_voltage(lcdb, &lcdb->ldo.voltage_mv, LDO); |
| if (rc < 0) { |
| pr_err("Failed to get LDO volatge rc=%d\n", rc); |
| return rc; |
| } |
| |
| lcdb->ldo.prev_voltage_mv = lcdb->ldo.voltage_mv; |
| |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| LCDB_LDO_VREG_OK_CTL_REG, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read ldo_vreg_ok rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->ldo.vreg_ok_dbc_us = dbc_us[val & VREG_OK_DEB_MASK]; |
| |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| LCDB_LDO_SOFT_START_CTL_REG, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read ldo_soft_start_ctl rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->ldo.soft_start_us = soft_start_us[val & SOFT_START_MASK]; |
| |
| rc = qpnp_lcdb_regulator_register(lcdb, LDO); |
| if (rc < 0) |
| pr_err("Failed to register ldo rc=%d\n", rc); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_init_ncp(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0, i = 0; |
| u8 val = 0; |
| |
| /* configure parameters only if LCDB is disabled */ |
| if (!is_lcdb_enabled(lcdb)) { |
| if (lcdb->ncp.voltage_mv != -EINVAL) { |
| rc = qpnp_lcdb_set_voltage(lcdb, |
| lcdb->ncp.voltage_mv, NCP); |
| if (rc < 0) { |
| pr_err("Failed to set voltage rc=%d\n", rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->ncp.pd != -EINVAL) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_NCP_PD_CTL_REG, NCP_DIS_PULLDOWN_BIT, |
| lcdb->ncp.pd ? 0 : NCP_DIS_PULLDOWN_BIT); |
| if (rc < 0) { |
| pr_err("Failed to configure NCP PD rc=%d\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->ncp.pd_strength != -EINVAL) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_NCP_PD_CTL_REG, NCP_PD_STRENGTH_BIT, |
| lcdb->ncp.pd_strength ? |
| NCP_PD_STRENGTH_BIT : 0); |
| if (rc < 0) { |
| pr_err("Failed to configure NCP PD strength %s rc=%d\n", |
| lcdb->ncp.pd_strength ? |
| "(strong)" : "(weak)", rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->ncp.ilim_ma != -EINVAL) { |
| while (lcdb->ncp.ilim_ma > ncp_ilim_ma[i]) |
| i++; |
| val = (i == 0) ? 0 : i - 1; |
| val = (lcdb->ncp.ilim_ma & SET_NCP_ILIM_MASK) | |
| EN_NCP_ILIM_BIT; |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_NCP_ILIM_CTL1_REG, |
| SET_NCP_ILIM_MASK | EN_NCP_ILIM_BIT, val); |
| if (rc < 0) { |
| pr_err("Failed to configure NCP ilim_ma (CTL1=%d) rc=%d\n", |
| val, rc); |
| return rc; |
| } |
| val = lcdb->ncp.ilim_ma & SET_NCP_ILIM_MASK; |
| rc = qpnp_lcdb_masked_write(lcdb, |
| lcdb->base + LCDB_NCP_ILIM_CTL2_REG, |
| SET_NCP_ILIM_MASK, val); |
| if (rc < 0) { |
| pr_err("Failed to configure NCP ilim_ma (CTL2=%d) rc=%d\n", |
| val, rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->ncp.soft_start_us != -EINVAL) { |
| rc = qpnp_lcdb_set_soft_start(lcdb, |
| lcdb->ncp.soft_start_us, NCP); |
| if (rc < 0) { |
| pr_err("Failed to set NCP soft_start rc=%d\n", |
| rc); |
| return rc; |
| } |
| } |
| } |
| |
| rc = qpnp_lcdb_get_voltage(lcdb, &lcdb->ncp.voltage_mv, NCP); |
| if (rc < 0) { |
| pr_err("Failed to get NCP volatge rc=%d\n", rc); |
| return rc; |
| } |
| |
| lcdb->ncp.prev_voltage_mv = lcdb->ncp.voltage_mv; |
| |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| LCDB_NCP_VREG_OK_CTL_REG, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read ncp_vreg_ok rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->ncp.vreg_ok_dbc_us = dbc_us[val & VREG_OK_DEB_MASK]; |
| |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| LCDB_NCP_SOFT_START_CTL_REG, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read ncp_soft_start_ctl rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->ncp.soft_start_us = soft_start_us[val & SOFT_START_MASK]; |
| |
| rc = qpnp_lcdb_regulator_register(lcdb, NCP); |
| if (rc < 0) |
| pr_err("Failed to register NCP rc=%d\n", rc); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_init_bst(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| u8 val, mask = 0; |
| u16 pmic_subtype = lcdb->pmic_rev_id->pmic_subtype; |
| |
| /* configure parameters only if LCDB is disabled */ |
| if (!is_lcdb_enabled(lcdb)) { |
| if (lcdb->bst.pd != -EINVAL) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_BST_PD_CTL_REG, BOOST_DIS_PULLDOWN_BIT, |
| lcdb->bst.pd ? 0 : BOOST_DIS_PULLDOWN_BIT); |
| if (rc < 0) { |
| pr_err("Failed to configure BST PD rc=%d\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->bst.pd_strength != -EINVAL) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_BST_PD_CTL_REG, BOOST_PD_STRENGTH_BIT, |
| lcdb->bst.pd_strength ? |
| BOOST_PD_STRENGTH_BIT : 0); |
| if (rc < 0) { |
| pr_err("Failed to configure NCP PD strength %s rc=%d\n", |
| lcdb->bst.pd_strength ? |
| "(strong)" : "(weak)", rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->bst.ilim_ma != -EINVAL) { |
| val = (lcdb->bst.ilim_ma / MIN_BST_ILIM_MA) - 1; |
| val = (lcdb->bst.ilim_ma & SET_BST_ILIM_MASK) | |
| EN_BST_ILIM_BIT; |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_BST_ILIM_CTL_REG, |
| SET_BST_ILIM_MASK | EN_BST_ILIM_BIT, val); |
| if (rc < 0) { |
| pr_err("Failed to configure BST ilim_ma rc=%d\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->bst.ps != -EINVAL) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_PS_CTL_REG, EN_PS_BIT, |
| lcdb->bst.ps ? EN_PS_BIT : 0); |
| if (rc < 0) { |
| pr_err("Failed to disable BST PS rc=%d\n", rc); |
| return rc; |
| } |
| } |
| |
| if (lcdb->bst.ps_threshold != -EINVAL) { |
| mask = (pmic_subtype == PM660L_SUBTYPE) ? |
| PM660_PS_THRESH_MASK : PS_THRESH_MASK; |
| val = (lcdb->bst.ps_threshold - MIN_BST_PS_MA) / 10; |
| val = (lcdb->bst.ps_threshold & mask) | EN_PS_BIT; |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_PS_CTL_REG, |
| mask | EN_PS_BIT, val); |
| if (rc < 0) { |
| pr_err("Failed to configure BST PS threshold rc=%d\n", |
| rc); |
| return rc; |
| } |
| } |
| } |
| |
| rc = qpnp_lcdb_get_voltage(lcdb, &lcdb->bst.voltage_mv, BST); |
| if (rc < 0) { |
| pr_err("Failed to get BST volatge rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| LCDB_BST_VREG_OK_CTL_REG, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read bst_vreg_ok rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->bst.vreg_ok_dbc_us = dbc_us[val & VREG_OK_DEB_MASK]; |
| |
| if (pmic_subtype == PM660L_SUBTYPE) { |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| LCDB_SOFT_START_CTL_REG, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read lcdb_soft_start_ctl rc=%d\n", |
| rc); |
| return rc; |
| } |
| lcdb->bst.soft_start_us = (val & SOFT_START_MASK) * 200 + 200; |
| if (!lcdb->bst.headroom_mv) |
| lcdb->bst.headroom_mv = PM660_BST_HEADROOM_DEFAULT_MV; |
| } else { |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| LCDB_BST_SS_CTL_REG, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read bst_soft_start_ctl rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->bst.soft_start_us = soft_start_us[val & SOFT_START_MASK]; |
| if (!lcdb->bst.headroom_mv) |
| lcdb->bst.headroom_mv = BST_HEADROOM_DEFAULT_MV; |
| } |
| |
| return 0; |
| } |
| |
| static void qpnp_lcdb_pmic_config(struct qpnp_lcdb *lcdb) |
| { |
| switch (lcdb->pmic_rev_id->pmic_subtype) { |
| case PM660L_SUBTYPE: |
| if (lcdb->pmic_rev_id->rev4 < PM660L_V2P0_REV4) |
| lcdb->wa_flags |= NCP_SCP_DISABLE_WA; |
| break; |
| case PMI632_SUBTYPE: |
| case PM6150L_SUBTYPE: |
| lcdb->wa_flags |= FORCE_PD_ENABLE_WA; |
| break; |
| default: |
| break; |
| } |
| |
| pr_debug("LCDB wa_flags = 0x%2x\n", lcdb->wa_flags); |
| } |
| |
| static int qpnp_lcdb_hw_init(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0; |
| u8 val = 0; |
| |
| qpnp_lcdb_pmic_config(lcdb); |
| |
| if (lcdb->pwrdn_delay_ms != -EINVAL) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_PWRUP_PWRDN_CTL_REG, |
| PWRDN_DELAY_MASK, |
| lcdb->pwrdn_delay_ms); |
| if (rc < 0) |
| return rc; |
| } |
| |
| rc = qpnp_lcdb_init_bst(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to initialize BOOST rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_lcdb_init_ldo(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to initialize LDO rc=%d\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_lcdb_init_ncp(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to initialize NCP rc=%d\n", rc); |
| return rc; |
| } |
| |
| if (lcdb->sc_irq >= 0 && !(lcdb->wa_flags & NCP_SCP_DISABLE_WA)) { |
| lcdb->sc_count = 0; |
| irq_set_status_flags(lcdb->sc_irq, |
| IRQ_DISABLE_UNLAZY); |
| rc = devm_request_threaded_irq(lcdb->dev, lcdb->sc_irq, |
| NULL, qpnp_lcdb_sc_irq_handler, IRQF_ONESHOT, |
| "qpnp_lcdb_sc_irq", lcdb); |
| if (rc < 0) { |
| pr_err("Unable to request sc(%d) irq rc=%d\n", |
| lcdb->sc_irq, rc); |
| return rc; |
| } |
| } |
| |
| if (!is_lcdb_enabled(lcdb)) { |
| rc = qpnp_lcdb_read(lcdb, lcdb->base + |
| LCDB_MODULE_RDY_REG, &val, 1); |
| if (rc < 0) { |
| pr_err("Failed to read MODULE_RDY rc=%d\n", rc); |
| return rc; |
| } |
| if (!(val & MODULE_RDY_BIT)) { |
| rc = qpnp_lcdb_masked_write(lcdb, lcdb->base + |
| LCDB_MODULE_RDY_REG, MODULE_RDY_BIT, |
| MODULE_RDY_BIT); |
| if (rc < 0) { |
| pr_err("Failed to set MODULE RDY rc=%d\n", rc); |
| return rc; |
| } |
| } |
| } else { |
| /* module already enabled */ |
| lcdb->lcdb_enabled = true; |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_lcdb_parse_dt(struct qpnp_lcdb *lcdb) |
| { |
| int rc = 0, i = 0; |
| u32 tmp; |
| const char *label; |
| struct device_node *revid_dev_node, *temp, *node = lcdb->dev->of_node; |
| |
| revid_dev_node = of_parse_phandle(node, "qcom,pmic-revid", 0); |
| if (!revid_dev_node) { |
| pr_err("Missing qcom,pmic-revid property - fail driver\n"); |
| return -EINVAL; |
| } |
| |
| lcdb->pmic_rev_id = get_revid_data(revid_dev_node); |
| if (IS_ERR(lcdb->pmic_rev_id)) { |
| pr_debug("Unable to get revid data\n"); |
| /* |
| * revid should to be defined, return -EPROBE_DEFER |
| * until the revid module registers. |
| */ |
| of_node_put(revid_dev_node); |
| return -EPROBE_DEFER; |
| } |
| |
| of_node_put(revid_dev_node); |
| for_each_available_child_of_node(node, temp) { |
| rc = of_property_read_string(temp, "label", &label); |
| if (rc < 0) { |
| pr_err("Failed to read label rc=%d\n", rc); |
| return rc; |
| } |
| |
| if (!strcmp(label, "ldo")) { |
| lcdb->ldo.node = temp; |
| rc = qpnp_lcdb_ldo_dt_init(lcdb); |
| } else if (!strcmp(label, "ncp")) { |
| lcdb->ncp.node = temp; |
| rc = qpnp_lcdb_ncp_dt_init(lcdb); |
| } else if (!strcmp(label, "bst")) { |
| lcdb->bst.node = temp; |
| rc = qpnp_lcdb_bst_dt_init(lcdb); |
| } else { |
| pr_err("Failed to identify label %s\n", label); |
| return -EINVAL; |
| } |
| if (rc < 0) { |
| pr_err("Failed to register %s module\n", label); |
| return rc; |
| } |
| } |
| |
| if (of_property_read_bool(node, "qcom,ttw-enable")) { |
| rc = qpnp_lcdb_parse_ttw(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to parse ttw-params rc=%d\n", rc); |
| return rc; |
| } |
| lcdb->ttw_enable = true; |
| } |
| |
| lcdb->sc_irq = platform_get_irq_byname(lcdb->pdev, "sc-irq"); |
| if (lcdb->sc_irq < 0) |
| pr_debug("sc irq is not defined\n"); |
| |
| lcdb->voltage_step_ramp = |
| of_property_read_bool(node, "qcom,voltage-step-ramp"); |
| |
| lcdb->pwrdn_delay_ms = -EINVAL; |
| rc = of_property_read_u32(node, "qcom,pwrdn-delay-ms", &tmp); |
| if (!rc) { |
| if (!is_between(tmp, PWRDN_DELAY_MIN_MS, PWRDN_DELAY_MAX_MS)) { |
| pr_err("Invalid PWRDN_DLY val %d (min=%d max=%d)\n", |
| tmp, PWRDN_DELAY_MIN_MS, PWRDN_DELAY_MAX_MS); |
| return -EINVAL; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(pwrup_pwrdn_ms); i++) { |
| if (tmp == pwrup_pwrdn_ms[i]) { |
| lcdb->pwrdn_delay_ms = i; |
| break; |
| } |
| } |
| } |
| |
| return 0; |
| } |
| |
| static ssize_t secure_mode_store(struct class *c, |
| struct class_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_lcdb *lcdb = container_of(c, struct qpnp_lcdb, |
| lcdb_class); |
| int val, rc; |
| |
| rc = kstrtouint(buf, 0, &val); |
| |
| if (rc < 0) |
| return rc; |
| |
| if (val != 0 && val != 1) |
| return count; |
| |
| if (val == 1 && !lcdb->secure_mode) { |
| if (lcdb->sc_irq > 0) |
| disable_irq(lcdb->sc_irq); |
| |
| lcdb->secure_mode = true; |
| } else if (val == 0 && lcdb->secure_mode) { |
| |
| if (lcdb->sc_irq > 0) |
| enable_irq(lcdb->sc_irq); |
| |
| lcdb->secure_mode = false; |
| } |
| |
| return count; |
| } |
| static CLASS_ATTR_WO(secure_mode); |
| |
| static struct attribute *lcdb_attrs[] = { |
| &class_attr_secure_mode.attr, |
| NULL, |
| }; |
| ATTRIBUTE_GROUPS(lcdb); |
| |
| static int qpnp_lcdb_regulator_probe(struct platform_device *pdev) |
| { |
| int rc; |
| struct device_node *node; |
| struct qpnp_lcdb *lcdb; |
| |
| node = pdev->dev.of_node; |
| if (!node) { |
| pr_err("No nodes defined\n"); |
| return -ENODEV; |
| } |
| |
| lcdb = devm_kzalloc(&pdev->dev, sizeof(*lcdb), GFP_KERNEL); |
| if (!lcdb) |
| return -ENOMEM; |
| |
| rc = of_property_read_u32(node, "reg", &lcdb->base); |
| if (rc < 0) { |
| pr_err("Failed to find reg node rc=%d\n", rc); |
| return rc; |
| } |
| |
| lcdb->regmap = dev_get_regmap(pdev->dev.parent, NULL); |
| if (!lcdb->regmap) { |
| pr_err("Failed to get the regmap handle rc=%d\n", rc); |
| return -EINVAL; |
| } |
| |
| lcdb->dev = &pdev->dev; |
| lcdb->pdev = pdev; |
| mutex_init(&lcdb->lcdb_mutex); |
| mutex_init(&lcdb->read_write_mutex); |
| |
| rc = qpnp_lcdb_parse_dt(lcdb); |
| if (rc < 0) { |
| pr_err("Failed to parse dt rc=%d\n", rc); |
| return rc; |
| } |
| |
| lcdb->lcdb_class.name = "lcd_bias"; |
| lcdb->lcdb_class.owner = THIS_MODULE; |
| lcdb->lcdb_class.class_groups = lcdb_groups; |
| |
| rc = class_register(&lcdb->lcdb_class); |
| if (rc < 0) { |
| pr_err("Failed to register lcdb class rc = %d\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_lcdb_hw_init(lcdb); |
| if (rc < 0) |
| pr_err("Failed to initialize LCDB module rc=%d\n", rc); |
| else |
| pr_info("LCDB module successfully registered! lcdb_en=%d ldo_voltage=%dmV ncp_voltage=%dmV bst_voltage=%dmV\n", |
| lcdb->lcdb_enabled, lcdb->ldo.voltage_mv, |
| lcdb->ncp.voltage_mv, lcdb->bst.voltage_mv); |
| |
| return rc; |
| } |
| |
| static int qpnp_lcdb_regulator_remove(struct platform_device *pdev) |
| { |
| struct qpnp_lcdb *lcdb = dev_get_drvdata(&pdev->dev); |
| |
| mutex_destroy(&lcdb->lcdb_mutex); |
| mutex_destroy(&lcdb->read_write_mutex); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id lcdb_match_table[] = { |
| { .compatible = QPNP_LCDB_REGULATOR_DRIVER_NAME, }, |
| { }, |
| }; |
| |
| static struct platform_driver qpnp_lcdb_regulator_driver = { |
| .driver = { |
| .name = QPNP_LCDB_REGULATOR_DRIVER_NAME, |
| .of_match_table = lcdb_match_table, |
| }, |
| .probe = qpnp_lcdb_regulator_probe, |
| .remove = qpnp_lcdb_regulator_remove, |
| }; |
| |
| static int __init qpnp_lcdb_regulator_init(void) |
| { |
| return platform_driver_register(&qpnp_lcdb_regulator_driver); |
| } |
| arch_initcall(qpnp_lcdb_regulator_init); |
| |
| static void __exit qpnp_lcdb_regulator_exit(void) |
| { |
| platform_driver_unregister(&qpnp_lcdb_regulator_driver); |
| } |
| module_exit(qpnp_lcdb_regulator_exit); |
| |
| MODULE_DESCRIPTION("QPNP LCDB regulator driver"); |
| MODULE_LICENSE("GPL v2"); |