| /* |
| * NAU85L40 ALSA SoC audio driver |
| * |
| * Copyright 2016 Nuvoton Technology Corp. |
| * Author: John Hsu <KCHSU0@nuvoton.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| #include <linux/init.h> |
| #include <linux/delay.h> |
| #include <linux/pm.h> |
| #include <linux/i2c.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/spi/spi.h> |
| #include <linux/slab.h> |
| #include <linux/of_device.h> |
| #include <sound/core.h> |
| #include <sound/pcm.h> |
| #include <sound/pcm_params.h> |
| #include <sound/soc.h> |
| #include <sound/soc-dapm.h> |
| #include <sound/initval.h> |
| #include <sound/tlv.h> |
| #include "nau8540.h" |
| |
| |
| #define NAU_FREF_MAX 13500000 |
| #define NAU_FVCO_MAX 100000000 |
| #define NAU_FVCO_MIN 90000000 |
| |
| /* the maximum frequency of CLK_ADC */ |
| #define CLK_ADC_MAX 6144000 |
| |
| /* scaling for mclk from sysclk_src output */ |
| static const struct nau8540_fll_attr mclk_src_scaling[] = { |
| { 1, 0x0 }, |
| { 2, 0x2 }, |
| { 4, 0x3 }, |
| { 8, 0x4 }, |
| { 16, 0x5 }, |
| { 32, 0x6 }, |
| { 3, 0x7 }, |
| { 6, 0xa }, |
| { 12, 0xb }, |
| { 24, 0xc }, |
| }; |
| |
| /* ratio for input clk freq */ |
| static const struct nau8540_fll_attr fll_ratio[] = { |
| { 512000, 0x01 }, |
| { 256000, 0x02 }, |
| { 128000, 0x04 }, |
| { 64000, 0x08 }, |
| { 32000, 0x10 }, |
| { 8000, 0x20 }, |
| { 4000, 0x40 }, |
| }; |
| |
| static const struct nau8540_fll_attr fll_pre_scalar[] = { |
| { 1, 0x0 }, |
| { 2, 0x1 }, |
| { 4, 0x2 }, |
| { 8, 0x3 }, |
| }; |
| |
| /* over sampling rate */ |
| static const struct nau8540_osr_attr osr_adc_sel[] = { |
| { 32, 3 }, /* OSR 32, SRC 1/8 */ |
| { 64, 2 }, /* OSR 64, SRC 1/4 */ |
| { 128, 1 }, /* OSR 128, SRC 1/2 */ |
| { 256, 0 }, /* OSR 256, SRC 1 */ |
| }; |
| |
| static const struct reg_default nau8540_reg_defaults[] = { |
| {NAU8540_REG_POWER_MANAGEMENT, 0x0000}, |
| {NAU8540_REG_CLOCK_CTRL, 0x0000}, |
| {NAU8540_REG_CLOCK_SRC, 0x0000}, |
| {NAU8540_REG_FLL1, 0x0001}, |
| {NAU8540_REG_FLL2, 0x3126}, |
| {NAU8540_REG_FLL3, 0x0008}, |
| {NAU8540_REG_FLL4, 0x0010}, |
| {NAU8540_REG_FLL5, 0xC000}, |
| {NAU8540_REG_FLL6, 0x6000}, |
| {NAU8540_REG_FLL_VCO_RSV, 0xF13C}, |
| {NAU8540_REG_PCM_CTRL0, 0x000B}, |
| {NAU8540_REG_PCM_CTRL1, 0x3010}, |
| {NAU8540_REG_PCM_CTRL2, 0x0800}, |
| {NAU8540_REG_PCM_CTRL3, 0x0000}, |
| {NAU8540_REG_PCM_CTRL4, 0x000F}, |
| {NAU8540_REG_ALC_CONTROL_1, 0x0000}, |
| {NAU8540_REG_ALC_CONTROL_2, 0x700B}, |
| {NAU8540_REG_ALC_CONTROL_3, 0x0022}, |
| {NAU8540_REG_ALC_CONTROL_4, 0x1010}, |
| {NAU8540_REG_ALC_CONTROL_5, 0x1010}, |
| {NAU8540_REG_NOTCH_FIL1_CH1, 0x0000}, |
| {NAU8540_REG_NOTCH_FIL2_CH1, 0x0000}, |
| {NAU8540_REG_NOTCH_FIL1_CH2, 0x0000}, |
| {NAU8540_REG_NOTCH_FIL2_CH2, 0x0000}, |
| {NAU8540_REG_NOTCH_FIL1_CH3, 0x0000}, |
| {NAU8540_REG_NOTCH_FIL2_CH3, 0x0000}, |
| {NAU8540_REG_NOTCH_FIL1_CH4, 0x0000}, |
| {NAU8540_REG_NOTCH_FIL2_CH4, 0x0000}, |
| {NAU8540_REG_HPF_FILTER_CH12, 0x0000}, |
| {NAU8540_REG_HPF_FILTER_CH34, 0x0000}, |
| {NAU8540_REG_ADC_SAMPLE_RATE, 0x0002}, |
| {NAU8540_REG_DIGITAL_GAIN_CH1, 0x0400}, |
| {NAU8540_REG_DIGITAL_GAIN_CH2, 0x0400}, |
| {NAU8540_REG_DIGITAL_GAIN_CH3, 0x0400}, |
| {NAU8540_REG_DIGITAL_GAIN_CH4, 0x0400}, |
| {NAU8540_REG_DIGITAL_MUX, 0x00E4}, |
| {NAU8540_REG_GPIO_CTRL, 0x0000}, |
| {NAU8540_REG_MISC_CTRL, 0x0000}, |
| {NAU8540_REG_I2C_CTRL, 0xEFFF}, |
| {NAU8540_REG_VMID_CTRL, 0x0000}, |
| {NAU8540_REG_MUTE, 0x0000}, |
| {NAU8540_REG_ANALOG_ADC1, 0x0011}, |
| {NAU8540_REG_ANALOG_ADC2, 0x0020}, |
| {NAU8540_REG_ANALOG_PWR, 0x0000}, |
| {NAU8540_REG_MIC_BIAS, 0x0004}, |
| {NAU8540_REG_REFERENCE, 0x0000}, |
| {NAU8540_REG_FEPGA1, 0x0000}, |
| {NAU8540_REG_FEPGA2, 0x0000}, |
| {NAU8540_REG_FEPGA3, 0x0101}, |
| {NAU8540_REG_FEPGA4, 0x0101}, |
| {NAU8540_REG_PWR, 0x0000}, |
| }; |
| |
| static bool nau8540_readable_reg(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case NAU8540_REG_POWER_MANAGEMENT ... NAU8540_REG_FLL_VCO_RSV: |
| case NAU8540_REG_PCM_CTRL0 ... NAU8540_REG_PCM_CTRL4: |
| case NAU8540_REG_ALC_CONTROL_1 ... NAU8540_REG_ALC_CONTROL_5: |
| case NAU8540_REG_ALC_GAIN_CH12 ... NAU8540_REG_ADC_SAMPLE_RATE: |
| case NAU8540_REG_DIGITAL_GAIN_CH1 ... NAU8540_REG_DIGITAL_MUX: |
| case NAU8540_REG_P2P_CH1 ... NAU8540_REG_I2C_CTRL: |
| case NAU8540_REG_I2C_DEVICE_ID: |
| case NAU8540_REG_VMID_CTRL ... NAU8540_REG_MUTE: |
| case NAU8540_REG_ANALOG_ADC1 ... NAU8540_REG_PWR: |
| return true; |
| default: |
| return false; |
| } |
| |
| } |
| |
| static bool nau8540_writeable_reg(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case NAU8540_REG_SW_RESET ... NAU8540_REG_FLL_VCO_RSV: |
| case NAU8540_REG_PCM_CTRL0 ... NAU8540_REG_PCM_CTRL4: |
| case NAU8540_REG_ALC_CONTROL_1 ... NAU8540_REG_ALC_CONTROL_5: |
| case NAU8540_REG_NOTCH_FIL1_CH1 ... NAU8540_REG_ADC_SAMPLE_RATE: |
| case NAU8540_REG_DIGITAL_GAIN_CH1 ... NAU8540_REG_DIGITAL_MUX: |
| case NAU8540_REG_GPIO_CTRL ... NAU8540_REG_I2C_CTRL: |
| case NAU8540_REG_RST: |
| case NAU8540_REG_VMID_CTRL ... NAU8540_REG_MUTE: |
| case NAU8540_REG_ANALOG_ADC1 ... NAU8540_REG_PWR: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static bool nau8540_volatile_reg(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case NAU8540_REG_SW_RESET: |
| case NAU8540_REG_ALC_GAIN_CH12 ... NAU8540_REG_ALC_STATUS: |
| case NAU8540_REG_P2P_CH1 ... NAU8540_REG_PEAK_CH4: |
| case NAU8540_REG_I2C_DEVICE_ID: |
| case NAU8540_REG_RST: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| |
| static const DECLARE_TLV_DB_MINMAX(adc_vol_tlv, -12800, 3600); |
| static const DECLARE_TLV_DB_MINMAX(fepga_gain_tlv, -100, 3600); |
| |
| static const struct snd_kcontrol_new nau8540_snd_controls[] = { |
| SOC_SINGLE_TLV("Mic1 Volume", NAU8540_REG_DIGITAL_GAIN_CH1, |
| 0, 0x520, 0, adc_vol_tlv), |
| SOC_SINGLE_TLV("Mic2 Volume", NAU8540_REG_DIGITAL_GAIN_CH2, |
| 0, 0x520, 0, adc_vol_tlv), |
| SOC_SINGLE_TLV("Mic3 Volume", NAU8540_REG_DIGITAL_GAIN_CH3, |
| 0, 0x520, 0, adc_vol_tlv), |
| SOC_SINGLE_TLV("Mic4 Volume", NAU8540_REG_DIGITAL_GAIN_CH4, |
| 0, 0x520, 0, adc_vol_tlv), |
| |
| SOC_SINGLE_TLV("Frontend PGA1 Volume", NAU8540_REG_FEPGA3, |
| 0, 0x25, 0, fepga_gain_tlv), |
| SOC_SINGLE_TLV("Frontend PGA2 Volume", NAU8540_REG_FEPGA3, |
| 8, 0x25, 0, fepga_gain_tlv), |
| SOC_SINGLE_TLV("Frontend PGA3 Volume", NAU8540_REG_FEPGA4, |
| 0, 0x25, 0, fepga_gain_tlv), |
| SOC_SINGLE_TLV("Frontend PGA4 Volume", NAU8540_REG_FEPGA4, |
| 8, 0x25, 0, fepga_gain_tlv), |
| }; |
| |
| static const char * const adc_channel[] = { |
| "ADC channel 1", "ADC channel 2", "ADC channel 3", "ADC channel 4" |
| }; |
| static SOC_ENUM_SINGLE_DECL( |
| digital_ch4_enum, NAU8540_REG_DIGITAL_MUX, 6, adc_channel); |
| |
| static const struct snd_kcontrol_new digital_ch4_mux = |
| SOC_DAPM_ENUM("Digital CH4 Select", digital_ch4_enum); |
| |
| static SOC_ENUM_SINGLE_DECL( |
| digital_ch3_enum, NAU8540_REG_DIGITAL_MUX, 4, adc_channel); |
| |
| static const struct snd_kcontrol_new digital_ch3_mux = |
| SOC_DAPM_ENUM("Digital CH3 Select", digital_ch3_enum); |
| |
| static SOC_ENUM_SINGLE_DECL( |
| digital_ch2_enum, NAU8540_REG_DIGITAL_MUX, 2, adc_channel); |
| |
| static const struct snd_kcontrol_new digital_ch2_mux = |
| SOC_DAPM_ENUM("Digital CH2 Select", digital_ch2_enum); |
| |
| static SOC_ENUM_SINGLE_DECL( |
| digital_ch1_enum, NAU8540_REG_DIGITAL_MUX, 0, adc_channel); |
| |
| static const struct snd_kcontrol_new digital_ch1_mux = |
| SOC_DAPM_ENUM("Digital CH1 Select", digital_ch1_enum); |
| |
| static const struct snd_soc_dapm_widget nau8540_dapm_widgets[] = { |
| SND_SOC_DAPM_SUPPLY("MICBIAS2", NAU8540_REG_MIC_BIAS, 11, 0, NULL, 0), |
| SND_SOC_DAPM_SUPPLY("MICBIAS1", NAU8540_REG_MIC_BIAS, 10, 0, NULL, 0), |
| |
| SND_SOC_DAPM_INPUT("MIC1"), |
| SND_SOC_DAPM_INPUT("MIC2"), |
| SND_SOC_DAPM_INPUT("MIC3"), |
| SND_SOC_DAPM_INPUT("MIC4"), |
| |
| SND_SOC_DAPM_PGA("Frontend PGA1", NAU8540_REG_PWR, 12, 0, NULL, 0), |
| SND_SOC_DAPM_PGA("Frontend PGA2", NAU8540_REG_PWR, 13, 0, NULL, 0), |
| SND_SOC_DAPM_PGA("Frontend PGA3", NAU8540_REG_PWR, 14, 0, NULL, 0), |
| SND_SOC_DAPM_PGA("Frontend PGA4", NAU8540_REG_PWR, 15, 0, NULL, 0), |
| |
| SND_SOC_DAPM_ADC("ADC1", NULL, |
| NAU8540_REG_POWER_MANAGEMENT, 0, 0), |
| SND_SOC_DAPM_ADC("ADC2", NULL, |
| NAU8540_REG_POWER_MANAGEMENT, 1, 0), |
| SND_SOC_DAPM_ADC("ADC3", NULL, |
| NAU8540_REG_POWER_MANAGEMENT, 2, 0), |
| SND_SOC_DAPM_ADC("ADC4", NULL, |
| NAU8540_REG_POWER_MANAGEMENT, 3, 0), |
| |
| SND_SOC_DAPM_PGA("ADC CH1", NAU8540_REG_ANALOG_PWR, 0, 0, NULL, 0), |
| SND_SOC_DAPM_PGA("ADC CH2", NAU8540_REG_ANALOG_PWR, 1, 0, NULL, 0), |
| SND_SOC_DAPM_PGA("ADC CH3", NAU8540_REG_ANALOG_PWR, 2, 0, NULL, 0), |
| SND_SOC_DAPM_PGA("ADC CH4", NAU8540_REG_ANALOG_PWR, 3, 0, NULL, 0), |
| |
| SND_SOC_DAPM_MUX("Digital CH4 Mux", |
| SND_SOC_NOPM, 0, 0, &digital_ch4_mux), |
| SND_SOC_DAPM_MUX("Digital CH3 Mux", |
| SND_SOC_NOPM, 0, 0, &digital_ch3_mux), |
| SND_SOC_DAPM_MUX("Digital CH2 Mux", |
| SND_SOC_NOPM, 0, 0, &digital_ch2_mux), |
| SND_SOC_DAPM_MUX("Digital CH1 Mux", |
| SND_SOC_NOPM, 0, 0, &digital_ch1_mux), |
| |
| SND_SOC_DAPM_AIF_OUT("AIFTX", "Capture", 0, SND_SOC_NOPM, 0, 0), |
| }; |
| |
| static const struct snd_soc_dapm_route nau8540_dapm_routes[] = { |
| {"Frontend PGA1", NULL, "MIC1"}, |
| {"Frontend PGA2", NULL, "MIC2"}, |
| {"Frontend PGA3", NULL, "MIC3"}, |
| {"Frontend PGA4", NULL, "MIC4"}, |
| |
| {"ADC1", NULL, "Frontend PGA1"}, |
| {"ADC2", NULL, "Frontend PGA2"}, |
| {"ADC3", NULL, "Frontend PGA3"}, |
| {"ADC4", NULL, "Frontend PGA4"}, |
| |
| {"ADC CH1", NULL, "ADC1"}, |
| {"ADC CH2", NULL, "ADC2"}, |
| {"ADC CH3", NULL, "ADC3"}, |
| {"ADC CH4", NULL, "ADC4"}, |
| |
| {"ADC1", NULL, "MICBIAS1"}, |
| {"ADC2", NULL, "MICBIAS1"}, |
| {"ADC3", NULL, "MICBIAS2"}, |
| {"ADC4", NULL, "MICBIAS2"}, |
| |
| {"Digital CH1 Mux", "ADC channel 1", "ADC CH1"}, |
| {"Digital CH1 Mux", "ADC channel 2", "ADC CH2"}, |
| {"Digital CH1 Mux", "ADC channel 3", "ADC CH3"}, |
| {"Digital CH1 Mux", "ADC channel 4", "ADC CH4"}, |
| |
| {"Digital CH2 Mux", "ADC channel 1", "ADC CH1"}, |
| {"Digital CH2 Mux", "ADC channel 2", "ADC CH2"}, |
| {"Digital CH2 Mux", "ADC channel 3", "ADC CH3"}, |
| {"Digital CH2 Mux", "ADC channel 4", "ADC CH4"}, |
| |
| {"Digital CH3 Mux", "ADC channel 1", "ADC CH1"}, |
| {"Digital CH3 Mux", "ADC channel 2", "ADC CH2"}, |
| {"Digital CH3 Mux", "ADC channel 3", "ADC CH3"}, |
| {"Digital CH3 Mux", "ADC channel 4", "ADC CH4"}, |
| |
| {"Digital CH4 Mux", "ADC channel 1", "ADC CH1"}, |
| {"Digital CH4 Mux", "ADC channel 2", "ADC CH2"}, |
| {"Digital CH4 Mux", "ADC channel 3", "ADC CH3"}, |
| {"Digital CH4 Mux", "ADC channel 4", "ADC CH4"}, |
| |
| {"AIFTX", NULL, "Digital CH1 Mux"}, |
| {"AIFTX", NULL, "Digital CH2 Mux"}, |
| {"AIFTX", NULL, "Digital CH3 Mux"}, |
| {"AIFTX", NULL, "Digital CH4 Mux"}, |
| }; |
| |
| static int nau8540_clock_check(struct nau8540 *nau8540, int rate, int osr) |
| { |
| int osrate; |
| |
| if (osr >= ARRAY_SIZE(osr_adc_sel)) |
| return -EINVAL; |
| osrate = osr_adc_sel[osr].osr; |
| |
| if (rate * osr > CLK_ADC_MAX) { |
| dev_err(nau8540->dev, "exceed the maximum frequency of CLK_ADC\n"); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int nau8540_hw_params(struct snd_pcm_substream *substream, |
| struct snd_pcm_hw_params *params, struct snd_soc_dai *dai) |
| { |
| struct snd_soc_codec *codec = dai->codec; |
| struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); |
| unsigned int val_len = 0, osr; |
| |
| /* CLK_ADC = OSR * FS |
| * ADC clock frequency is defined as Over Sampling Rate (OSR) |
| * multiplied by the audio sample rate (Fs). Note that the OSR and Fs |
| * values must be selected such that the maximum frequency is less |
| * than 6.144 MHz. |
| */ |
| regmap_read(nau8540->regmap, NAU8540_REG_ADC_SAMPLE_RATE, &osr); |
| osr &= NAU8540_ADC_OSR_MASK; |
| if (nau8540_clock_check(nau8540, params_rate(params), osr)) |
| return -EINVAL; |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_CLOCK_SRC, |
| NAU8540_CLK_ADC_SRC_MASK, |
| osr_adc_sel[osr].clk_src << NAU8540_CLK_ADC_SRC_SFT); |
| |
| switch (params_width(params)) { |
| case 16: |
| val_len |= NAU8540_I2S_DL_16; |
| break; |
| case 20: |
| val_len |= NAU8540_I2S_DL_20; |
| break; |
| case 24: |
| val_len |= NAU8540_I2S_DL_24; |
| break; |
| case 32: |
| val_len |= NAU8540_I2S_DL_32; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL0, |
| NAU8540_I2S_DL_MASK, val_len); |
| |
| return 0; |
| } |
| |
| static int nau8540_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) |
| { |
| struct snd_soc_codec *codec = dai->codec; |
| struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); |
| unsigned int ctrl1_val = 0, ctrl2_val = 0; |
| |
| switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) { |
| case SND_SOC_DAIFMT_CBM_CFM: |
| ctrl2_val |= NAU8540_I2S_MS_MASTER; |
| break; |
| case SND_SOC_DAIFMT_CBS_CFS: |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| switch (fmt & SND_SOC_DAIFMT_INV_MASK) { |
| case SND_SOC_DAIFMT_NB_NF: |
| break; |
| case SND_SOC_DAIFMT_IB_NF: |
| ctrl1_val |= NAU8540_I2S_BP_INV; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { |
| case SND_SOC_DAIFMT_I2S: |
| ctrl1_val |= NAU8540_I2S_DF_I2S; |
| break; |
| case SND_SOC_DAIFMT_LEFT_J: |
| ctrl1_val |= NAU8540_I2S_DF_LEFT; |
| break; |
| case SND_SOC_DAIFMT_RIGHT_J: |
| ctrl1_val |= NAU8540_I2S_DF_RIGTH; |
| break; |
| case SND_SOC_DAIFMT_DSP_A: |
| ctrl1_val |= NAU8540_I2S_DF_PCM_AB; |
| break; |
| case SND_SOC_DAIFMT_DSP_B: |
| ctrl1_val |= NAU8540_I2S_DF_PCM_AB; |
| ctrl1_val |= NAU8540_I2S_PCMB_EN; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL0, |
| NAU8540_I2S_DL_MASK | NAU8540_I2S_DF_MASK | |
| NAU8540_I2S_BP_INV | NAU8540_I2S_PCMB_EN, ctrl1_val); |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL1, |
| NAU8540_I2S_MS_MASK | NAU8540_I2S_DO12_OE, ctrl2_val); |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL2, |
| NAU8540_I2S_DO34_OE, 0); |
| |
| return 0; |
| } |
| |
| /** |
| * nau8540_set_tdm_slot - configure DAI TX TDM. |
| * @dai: DAI |
| * @tx_mask: bitmask representing active TX slots. Ex. |
| * 0xf for normal 4 channel TDM. |
| * 0xf0 for shifted 4 channel TDM |
| * @rx_mask: no used. |
| * @slots: Number of slots in use. |
| * @slot_width: Width in bits for each slot. |
| * |
| * Configures a DAI for TDM operation. Only support 4 slots TDM. |
| */ |
| static int nau8540_set_tdm_slot(struct snd_soc_dai *dai, |
| unsigned int tx_mask, unsigned int rx_mask, int slots, int slot_width) |
| { |
| struct snd_soc_codec *codec = dai->codec; |
| struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); |
| unsigned int ctrl2_val = 0, ctrl4_val = 0; |
| |
| if (slots > 4 || ((tx_mask & 0xf0) && (tx_mask & 0xf))) |
| return -EINVAL; |
| |
| ctrl4_val |= (NAU8540_TDM_MODE | NAU8540_TDM_OFFSET_EN); |
| if (tx_mask & 0xf0) { |
| ctrl2_val = 4 * slot_width; |
| ctrl4_val |= (tx_mask >> 4); |
| } else { |
| ctrl4_val |= tx_mask; |
| } |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL4, |
| NAU8540_TDM_MODE | NAU8540_TDM_OFFSET_EN | |
| NAU8540_TDM_TX_MASK, ctrl4_val); |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL1, |
| NAU8540_I2S_DO12_OE, NAU8540_I2S_DO12_OE); |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_PCM_CTRL2, |
| NAU8540_I2S_DO34_OE | NAU8540_I2S_TSLOT_L_MASK, |
| NAU8540_I2S_DO34_OE | ctrl2_val); |
| |
| return 0; |
| } |
| |
| |
| static const struct snd_soc_dai_ops nau8540_dai_ops = { |
| .hw_params = nau8540_hw_params, |
| .set_fmt = nau8540_set_fmt, |
| .set_tdm_slot = nau8540_set_tdm_slot, |
| }; |
| |
| #define NAU8540_RATES SNDRV_PCM_RATE_8000_48000 |
| #define NAU8540_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE \ |
| | SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S32_LE) |
| |
| static struct snd_soc_dai_driver nau8540_dai = { |
| .name = "nau8540-hifi", |
| .capture = { |
| .stream_name = "Capture", |
| .channels_min = 1, |
| .channels_max = 4, |
| .rates = NAU8540_RATES, |
| .formats = NAU8540_FORMATS, |
| }, |
| .ops = &nau8540_dai_ops, |
| }; |
| |
| /** |
| * nau8540_calc_fll_param - Calculate FLL parameters. |
| * @fll_in: external clock provided to codec. |
| * @fs: sampling rate. |
| * @fll_param: Pointer to structure of FLL parameters. |
| * |
| * Calculate FLL parameters to configure codec. |
| * |
| * Returns 0 for success or negative error code. |
| */ |
| static int nau8540_calc_fll_param(unsigned int fll_in, |
| unsigned int fs, struct nau8540_fll *fll_param) |
| { |
| u64 fvco, fvco_max; |
| unsigned int fref, i, fvco_sel; |
| |
| /* Ensure the reference clock frequency (FREF) is <= 13.5MHz by dividing |
| * freq_in by 1, 2, 4, or 8 using FLL pre-scalar. |
| * FREF = freq_in / NAU8540_FLL_REF_DIV_MASK |
| */ |
| for (i = 0; i < ARRAY_SIZE(fll_pre_scalar); i++) { |
| fref = fll_in / fll_pre_scalar[i].param; |
| if (fref <= NAU_FREF_MAX) |
| break; |
| } |
| if (i == ARRAY_SIZE(fll_pre_scalar)) |
| return -EINVAL; |
| fll_param->clk_ref_div = fll_pre_scalar[i].val; |
| |
| /* Choose the FLL ratio based on FREF */ |
| for (i = 0; i < ARRAY_SIZE(fll_ratio); i++) { |
| if (fref >= fll_ratio[i].param) |
| break; |
| } |
| if (i == ARRAY_SIZE(fll_ratio)) |
| return -EINVAL; |
| fll_param->ratio = fll_ratio[i].val; |
| |
| /* Calculate the frequency of DCO (FDCO) given freq_out = 256 * Fs. |
| * FDCO must be within the 90MHz - 124MHz or the FFL cannot be |
| * guaranteed across the full range of operation. |
| * FDCO = freq_out * 2 * mclk_src_scaling |
| */ |
| fvco_max = 0; |
| fvco_sel = ARRAY_SIZE(mclk_src_scaling); |
| for (i = 0; i < ARRAY_SIZE(mclk_src_scaling); i++) { |
| fvco = 256 * fs * 2 * mclk_src_scaling[i].param; |
| if (fvco > NAU_FVCO_MIN && fvco < NAU_FVCO_MAX && |
| fvco_max < fvco) { |
| fvco_max = fvco; |
| fvco_sel = i; |
| } |
| } |
| if (ARRAY_SIZE(mclk_src_scaling) == fvco_sel) |
| return -EINVAL; |
| fll_param->mclk_src = mclk_src_scaling[fvco_sel].val; |
| |
| /* Calculate the FLL 10-bit integer input and the FLL 16-bit fractional |
| * input based on FDCO, FREF and FLL ratio. |
| */ |
| fvco = div_u64(fvco_max << 16, fref * fll_param->ratio); |
| fll_param->fll_int = (fvco >> 16) & 0x3FF; |
| fll_param->fll_frac = fvco & 0xFFFF; |
| return 0; |
| } |
| |
| static void nau8540_fll_apply(struct regmap *regmap, |
| struct nau8540_fll *fll_param) |
| { |
| regmap_update_bits(regmap, NAU8540_REG_CLOCK_SRC, |
| NAU8540_CLK_SRC_MASK | NAU8540_CLK_MCLK_SRC_MASK, |
| NAU8540_CLK_SRC_MCLK | fll_param->mclk_src); |
| regmap_update_bits(regmap, NAU8540_REG_FLL1, |
| NAU8540_FLL_RATIO_MASK, fll_param->ratio); |
| /* FLL 16-bit fractional input */ |
| regmap_write(regmap, NAU8540_REG_FLL2, fll_param->fll_frac); |
| /* FLL 10-bit integer input */ |
| regmap_update_bits(regmap, NAU8540_REG_FLL3, |
| NAU8540_FLL_INTEGER_MASK, fll_param->fll_int); |
| /* FLL pre-scaler */ |
| regmap_update_bits(regmap, NAU8540_REG_FLL4, |
| NAU8540_FLL_REF_DIV_MASK, |
| fll_param->clk_ref_div << NAU8540_FLL_REF_DIV_SFT); |
| regmap_update_bits(regmap, NAU8540_REG_FLL5, |
| NAU8540_FLL_CLK_SW_MASK, NAU8540_FLL_CLK_SW_REF); |
| regmap_update_bits(regmap, |
| NAU8540_REG_FLL6, NAU8540_DCO_EN, 0); |
| if (fll_param->fll_frac) { |
| regmap_update_bits(regmap, NAU8540_REG_FLL5, |
| NAU8540_FLL_PDB_DAC_EN | NAU8540_FLL_LOOP_FTR_EN | |
| NAU8540_FLL_FTR_SW_MASK, |
| NAU8540_FLL_PDB_DAC_EN | NAU8540_FLL_LOOP_FTR_EN | |
| NAU8540_FLL_FTR_SW_FILTER); |
| regmap_update_bits(regmap, NAU8540_REG_FLL6, |
| NAU8540_SDM_EN, NAU8540_SDM_EN); |
| } else { |
| regmap_update_bits(regmap, NAU8540_REG_FLL5, |
| NAU8540_FLL_PDB_DAC_EN | NAU8540_FLL_LOOP_FTR_EN | |
| NAU8540_FLL_FTR_SW_MASK, NAU8540_FLL_FTR_SW_ACCU); |
| regmap_update_bits(regmap, |
| NAU8540_REG_FLL6, NAU8540_SDM_EN, 0); |
| } |
| } |
| |
| /* freq_out must be 256*Fs in order to achieve the best performance */ |
| static int nau8540_set_pll(struct snd_soc_codec *codec, int pll_id, int source, |
| unsigned int freq_in, unsigned int freq_out) |
| { |
| struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); |
| struct nau8540_fll fll_param; |
| int ret, fs; |
| |
| switch (pll_id) { |
| case NAU8540_CLK_FLL_MCLK: |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_FLL3, |
| NAU8540_FLL_CLK_SRC_MASK, NAU8540_FLL_CLK_SRC_MCLK); |
| break; |
| |
| case NAU8540_CLK_FLL_BLK: |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_FLL3, |
| NAU8540_FLL_CLK_SRC_MASK, NAU8540_FLL_CLK_SRC_BLK); |
| break; |
| |
| case NAU8540_CLK_FLL_FS: |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_FLL3, |
| NAU8540_FLL_CLK_SRC_MASK, NAU8540_FLL_CLK_SRC_FS); |
| break; |
| |
| default: |
| dev_err(nau8540->dev, "Invalid clock id (%d)\n", pll_id); |
| return -EINVAL; |
| } |
| dev_dbg(nau8540->dev, "Sysclk is %dHz and clock id is %d\n", |
| freq_out, pll_id); |
| |
| fs = freq_out / 256; |
| ret = nau8540_calc_fll_param(freq_in, fs, &fll_param); |
| if (ret < 0) { |
| dev_err(nau8540->dev, "Unsupported input clock %d\n", freq_in); |
| return ret; |
| } |
| dev_dbg(nau8540->dev, "mclk_src=%x ratio=%x fll_frac=%x fll_int=%x clk_ref_div=%x\n", |
| fll_param.mclk_src, fll_param.ratio, fll_param.fll_frac, |
| fll_param.fll_int, fll_param.clk_ref_div); |
| |
| nau8540_fll_apply(nau8540->regmap, &fll_param); |
| mdelay(2); |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_CLOCK_SRC, |
| NAU8540_CLK_SRC_MASK, NAU8540_CLK_SRC_VCO); |
| |
| return 0; |
| } |
| |
| static int nau8540_set_sysclk(struct snd_soc_codec *codec, |
| int clk_id, int source, unsigned int freq, int dir) |
| { |
| struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); |
| |
| switch (clk_id) { |
| case NAU8540_CLK_DIS: |
| case NAU8540_CLK_MCLK: |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_CLOCK_SRC, |
| NAU8540_CLK_SRC_MASK, NAU8540_CLK_SRC_MCLK); |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_FLL6, |
| NAU8540_DCO_EN, 0); |
| break; |
| |
| case NAU8540_CLK_INTERNAL: |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_FLL6, |
| NAU8540_DCO_EN, NAU8540_DCO_EN); |
| regmap_update_bits(nau8540->regmap, NAU8540_REG_CLOCK_SRC, |
| NAU8540_CLK_SRC_MASK, NAU8540_CLK_SRC_VCO); |
| break; |
| |
| default: |
| dev_err(nau8540->dev, "Invalid clock id (%d)\n", clk_id); |
| return -EINVAL; |
| } |
| |
| dev_dbg(nau8540->dev, "Sysclk is %dHz and clock id is %d\n", |
| freq, clk_id); |
| |
| return 0; |
| } |
| |
| static void nau8540_reset_chip(struct regmap *regmap) |
| { |
| regmap_write(regmap, NAU8540_REG_SW_RESET, 0x00); |
| regmap_write(regmap, NAU8540_REG_SW_RESET, 0x00); |
| } |
| |
| static void nau8540_init_regs(struct nau8540 *nau8540) |
| { |
| struct regmap *regmap = nau8540->regmap; |
| |
| /* Enable Bias/VMID/VMID Tieoff */ |
| regmap_update_bits(regmap, NAU8540_REG_VMID_CTRL, |
| NAU8540_VMID_EN | NAU8540_VMID_SEL_MASK, |
| NAU8540_VMID_EN | (0x2 << NAU8540_VMID_SEL_SFT)); |
| regmap_update_bits(regmap, NAU8540_REG_REFERENCE, |
| NAU8540_PRECHARGE_DIS | NAU8540_GLOBAL_BIAS_EN, |
| NAU8540_PRECHARGE_DIS | NAU8540_GLOBAL_BIAS_EN); |
| mdelay(2); |
| regmap_update_bits(regmap, NAU8540_REG_MIC_BIAS, |
| NAU8540_PU_PRE, NAU8540_PU_PRE); |
| regmap_update_bits(regmap, NAU8540_REG_CLOCK_CTRL, |
| NAU8540_CLK_ADC_EN | NAU8540_CLK_I2S_EN, |
| NAU8540_CLK_ADC_EN | NAU8540_CLK_I2S_EN); |
| /* ADC OSR selection, CLK_ADC = Fs * OSR */ |
| regmap_update_bits(regmap, NAU8540_REG_ADC_SAMPLE_RATE, |
| NAU8540_ADC_OSR_MASK, NAU8540_ADC_OSR_64); |
| } |
| |
| static int __maybe_unused nau8540_suspend(struct snd_soc_codec *codec) |
| { |
| struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); |
| |
| regcache_cache_only(nau8540->regmap, true); |
| regcache_mark_dirty(nau8540->regmap); |
| |
| return 0; |
| } |
| |
| static int __maybe_unused nau8540_resume(struct snd_soc_codec *codec) |
| { |
| struct nau8540 *nau8540 = snd_soc_codec_get_drvdata(codec); |
| |
| regcache_cache_only(nau8540->regmap, false); |
| regcache_sync(nau8540->regmap); |
| |
| return 0; |
| } |
| |
| static struct snd_soc_codec_driver nau8540_codec_driver = { |
| .set_sysclk = nau8540_set_sysclk, |
| .set_pll = nau8540_set_pll, |
| .suspend = nau8540_suspend, |
| .resume = nau8540_resume, |
| .suspend_bias_off = true, |
| |
| .component_driver = { |
| .controls = nau8540_snd_controls, |
| .num_controls = ARRAY_SIZE(nau8540_snd_controls), |
| .dapm_widgets = nau8540_dapm_widgets, |
| .num_dapm_widgets = ARRAY_SIZE(nau8540_dapm_widgets), |
| .dapm_routes = nau8540_dapm_routes, |
| .num_dapm_routes = ARRAY_SIZE(nau8540_dapm_routes), |
| }, |
| }; |
| |
| static const struct regmap_config nau8540_regmap_config = { |
| .val_bits = 16, |
| .reg_bits = 16, |
| |
| .max_register = NAU8540_REG_MAX, |
| .readable_reg = nau8540_readable_reg, |
| .writeable_reg = nau8540_writeable_reg, |
| .volatile_reg = nau8540_volatile_reg, |
| |
| .cache_type = REGCACHE_RBTREE, |
| .reg_defaults = nau8540_reg_defaults, |
| .num_reg_defaults = ARRAY_SIZE(nau8540_reg_defaults), |
| }; |
| |
| static int nau8540_i2c_probe(struct i2c_client *i2c, |
| const struct i2c_device_id *id) |
| { |
| struct device *dev = &i2c->dev; |
| struct nau8540 *nau8540 = dev_get_platdata(dev); |
| int ret, value; |
| |
| if (!nau8540) { |
| nau8540 = devm_kzalloc(dev, sizeof(*nau8540), GFP_KERNEL); |
| if (!nau8540) |
| return -ENOMEM; |
| } |
| i2c_set_clientdata(i2c, nau8540); |
| |
| nau8540->regmap = devm_regmap_init_i2c(i2c, &nau8540_regmap_config); |
| if (IS_ERR(nau8540->regmap)) |
| return PTR_ERR(nau8540->regmap); |
| ret = regmap_read(nau8540->regmap, NAU8540_REG_I2C_DEVICE_ID, &value); |
| if (ret < 0) { |
| dev_err(dev, "Failed to read device id from the NAU85L40: %d\n", |
| ret); |
| return ret; |
| } |
| |
| nau8540->dev = dev; |
| nau8540_reset_chip(nau8540->regmap); |
| nau8540_init_regs(nau8540); |
| |
| return snd_soc_register_codec(dev, |
| &nau8540_codec_driver, &nau8540_dai, 1); |
| } |
| |
| static int nau8540_i2c_remove(struct i2c_client *client) |
| { |
| snd_soc_unregister_codec(&client->dev); |
| return 0; |
| } |
| |
| |
| static const struct i2c_device_id nau8540_i2c_ids[] = { |
| { "nau8540", 0 }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(i2c, nau8540_i2c_ids); |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id nau8540_of_ids[] = { |
| { .compatible = "nuvoton,nau8540", }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, nau8540_of_ids); |
| #endif |
| |
| static struct i2c_driver nau8540_i2c_driver = { |
| .driver = { |
| .name = "nau8540", |
| .of_match_table = of_match_ptr(nau8540_of_ids), |
| }, |
| .probe = nau8540_i2c_probe, |
| .remove = nau8540_i2c_remove, |
| .id_table = nau8540_i2c_ids, |
| }; |
| module_i2c_driver(nau8540_i2c_driver); |
| |
| MODULE_DESCRIPTION("ASoC NAU85L40 driver"); |
| MODULE_AUTHOR("John Hsu <KCHSU0@nuvoton.com>"); |
| MODULE_LICENSE("GPL v2"); |