| /* |
| * Sun3 SCSI stuff by Erik Verbruggen (erik@bigmama.xtdnet.nl) |
| * |
| * Sun3 DMA additions by Sam Creasey (sammy@sammy.net) |
| * |
| * Adapted from mac_scsinew.h: |
| */ |
| /* |
| * Cumana Generic NCR5380 driver defines |
| * |
| * Copyright 1993, Drew Eckhardt |
| * Visionary Computing |
| * (Unix and Linux consulting and custom programming) |
| * drew@colorado.edu |
| * +1 (303) 440-4894 |
| * |
| * ALPHA RELEASE 1. |
| * |
| * For more information, please consult |
| * |
| * NCR 5380 Family |
| * SCSI Protocol Controller |
| * Databook |
| * |
| * NCR Microelectronics |
| * 1635 Aeroplaza Drive |
| * Colorado Springs, CO 80916 |
| * 1+ (719) 578-3400 |
| * 1+ (800) 334-5454 |
| */ |
| |
| #ifndef SUN3_SCSI_H |
| #define SUN3_SCSI_H |
| |
| #define SUN3SCSI_PUBLIC_RELEASE 1 |
| |
| /* |
| * Int: level 2 autovector |
| * IO: type 1, base 0x00140000, 5 bits phys space: A<4..0> |
| */ |
| #define IRQ_SUN3_SCSI 2 |
| #define IOBASE_SUN3_SCSI 0x00140000 |
| |
| #define IOBASE_SUN3_VMESCSI 0xff200000 |
| |
| #ifndef CMD_PER_LUN |
| #define CMD_PER_LUN 2 |
| #endif |
| |
| #ifndef CAN_QUEUE |
| #define CAN_QUEUE 16 |
| #endif |
| |
| #ifndef SG_TABLESIZE |
| #define SG_TABLESIZE SG_NONE |
| #endif |
| |
| #ifndef MAX_TAGS |
| #define MAX_TAGS 32 |
| #endif |
| |
| #ifndef USE_TAGGED_QUEUING |
| #define USE_TAGGED_QUEUING 1 |
| #endif |
| |
| #include <scsi/scsicam.h> |
| |
| #ifdef SUN3_SCSI_VME |
| #define SUN3_SCSI_NAME "Sun3 NCR5380 VME SCSI" |
| #else |
| #define SUN3_SCSI_NAME "Sun3 NCR5380 SCSI" |
| #endif |
| |
| #define NCR5380_implementation_fields /* none */ |
| |
| #define NCR5380_local_declare() \ |
| struct Scsi_Host *_instance |
| |
| #define NCR5380_setup(instance) \ |
| _instance = instance |
| |
| #define NCR5380_read(reg) sun3scsi_read(reg) |
| #define NCR5380_write(reg, value) sun3scsi_write(reg, value) |
| |
| #define NCR5380_queue_command sun3scsi_queue_command |
| #define NCR5380_bus_reset sun3scsi_bus_reset |
| #define NCR5380_abort sun3scsi_abort |
| #define NCR5380_show_info sun3scsi_show_info |
| #define NCR5380_dma_xfer_len(i, cmd, phase) \ |
| sun3scsi_dma_xfer_len(cmd->SCp.this_residual,cmd,((phase) & SR_IO) ? 0 : 1) |
| |
| #define NCR5380_dma_write_setup(instance, data, count) sun3scsi_dma_setup(data, count, 1) |
| #define NCR5380_dma_read_setup(instance, data, count) sun3scsi_dma_setup(data, count, 0) |
| #define NCR5380_dma_residual sun3scsi_dma_residual |
| |
| /* additional registers - mainly DMA control regs */ |
| /* these start at regbase + 8 -- directly after the NCR regs */ |
| struct sun3_dma_regs { |
| unsigned short dma_addr_hi; /* vme only */ |
| unsigned short dma_addr_lo; /* vme only */ |
| unsigned short dma_count_hi; /* vme only */ |
| unsigned short dma_count_lo; /* vme only */ |
| unsigned short udc_data; /* udc dma data reg (obio only) */ |
| unsigned short udc_addr; /* uda dma addr reg (obio only) */ |
| unsigned short fifo_data; /* fifo data reg, holds extra byte on |
| odd dma reads */ |
| unsigned short fifo_count; |
| unsigned short csr; /* control/status reg */ |
| unsigned short bpack_hi; /* vme only */ |
| unsigned short bpack_lo; /* vme only */ |
| unsigned short ivect; /* vme only */ |
| unsigned short fifo_count_hi; /* vme only */ |
| }; |
| |
| /* ucd chip specific regs - live in dvma space */ |
| struct sun3_udc_regs { |
| unsigned short rsel; /* select regs to load */ |
| unsigned short addr_hi; /* high word of addr */ |
| unsigned short addr_lo; /* low word */ |
| unsigned short count; /* words to be xfer'd */ |
| unsigned short mode_hi; /* high word of channel mode */ |
| unsigned short mode_lo; /* low word of channel mode */ |
| }; |
| |
| /* addresses of the udc registers */ |
| #define UDC_MODE 0x38 |
| #define UDC_CSR 0x2e /* command/status */ |
| #define UDC_CHN_HI 0x26 /* chain high word */ |
| #define UDC_CHN_LO 0x22 /* chain lo word */ |
| #define UDC_CURA_HI 0x1a /* cur reg A high */ |
| #define UDC_CURA_LO 0x0a /* cur reg A low */ |
| #define UDC_CURB_HI 0x12 /* cur reg B high */ |
| #define UDC_CURB_LO 0x02 /* cur reg B low */ |
| #define UDC_MODE_HI 0x56 /* mode reg high */ |
| #define UDC_MODE_LO 0x52 /* mode reg low */ |
| #define UDC_COUNT 0x32 /* words to xfer */ |
| |
| /* some udc commands */ |
| #define UDC_RESET 0 |
| #define UDC_CHN_START 0xa0 /* start chain */ |
| #define UDC_INT_ENABLE 0x32 /* channel 1 int on */ |
| |
| /* udc mode words */ |
| #define UDC_MODE_HIWORD 0x40 |
| #define UDC_MODE_LSEND 0xc2 |
| #define UDC_MODE_LRECV 0xd2 |
| |
| /* udc reg selections */ |
| #define UDC_RSEL_SEND 0x282 |
| #define UDC_RSEL_RECV 0x182 |
| |
| /* bits in csr reg */ |
| #define CSR_DMA_ACTIVE 0x8000 |
| #define CSR_DMA_CONFLICT 0x4000 |
| #define CSR_DMA_BUSERR 0x2000 |
| |
| #define CSR_FIFO_EMPTY 0x400 /* fifo flushed? */ |
| #define CSR_SDB_INT 0x200 /* sbc interrupt pending */ |
| #define CSR_DMA_INT 0x100 /* dma interrupt pending */ |
| |
| #define CSR_LEFT 0xc0 |
| #define CSR_LEFT_3 0xc0 |
| #define CSR_LEFT_2 0x80 |
| #define CSR_LEFT_1 0x40 |
| #define CSR_PACK_ENABLE 0x20 |
| |
| #define CSR_DMA_ENABLE 0x10 |
| |
| #define CSR_SEND 0x8 /* 1 = send 0 = recv */ |
| #define CSR_FIFO 0x2 /* reset fifo */ |
| #define CSR_INTR 0x4 /* interrupt enable */ |
| #define CSR_SCSI 0x1 |
| |
| #define VME_DATA24 0x3d00 |
| |
| #endif /* SUN3_SCSI_H */ |
| |