drivers/net/wireless/b43/phy_a.h - kernel/msm-4.19 - Gitiles

 #ifndef LINUX_B43_PHY_A_H_
 #define LINUX_B43_PHY_A_H_

 #include "phy_common.h"


 /* OFDM (A) PHY Registers */
 #define B43_PHY_VERSION_OFDM		B43_PHY_OFDM(0x00)	/* Versioning register for A-PHY */
 #define B43_PHY_BBANDCFG		B43_PHY_OFDM(0x01)	/* Baseband config */
 #define  B43_PHY_BBANDCFG_RXANT		0x180	/* RX Antenna selection */
 #define  B43_PHY_BBANDCFG_RXANT_SHIFT	7
 #define B43_PHY_PWRDOWN			B43_PHY_OFDM(0x03)	/* Powerdown */
 #define B43_PHY_CRSTHRES1_R1		B43_PHY_OFDM(0x06)	/* CRS Threshold 1 (phy.rev 1 only) */
 #define B43_PHY_LNAHPFCTL		B43_PHY_OFDM(0x1C)	/* LNA/HPF control */
 #define B43_PHY_LPFGAINCTL		B43_PHY_OFDM(0x20)	/* LPF Gain control */
 #define B43_PHY_ADIVRELATED		B43_PHY_OFDM(0x27)	/* FIXME rename */
 #define B43_PHY_CRS0			B43_PHY_OFDM(0x29)
 #define  B43_PHY_CRS0_EN		0x4000
 #define B43_PHY_PEAK_COUNT		B43_PHY_OFDM(0x30)
 #define B43_PHY_ANTDWELL		B43_PHY_OFDM(0x2B)	/* Antenna dwell */
 #define  B43_PHY_ANTDWELL_AUTODIV1	0x0100	/* Automatic RX diversity start antenna */
 #define B43_PHY_ENCORE			B43_PHY_OFDM(0x49)	/* "Encore" (RangeMax / BroadRange) */
 #define  B43_PHY_ENCORE_EN		0x0200	/* Encore enable */
 #define B43_PHY_LMS			B43_PHY_OFDM(0x55)
 #define B43_PHY_OFDM61			B43_PHY_OFDM(0x61)	/* FIXME rename */
 #define  B43_PHY_OFDM61_10		0x0010	/* FIXME rename */
 #define B43_PHY_IQBAL			B43_PHY_OFDM(0x69)	/* I/Q balance */
 #define B43_PHY_BBTXDC_BIAS		B43_PHY_OFDM(0x6B)	/* Baseband TX DC bias */
 #define B43_PHY_OTABLECTL		B43_PHY_OFDM(0x72)	/* OFDM table control (see below) */
 #define  B43_PHY_OTABLEOFF		0x03FF	/* OFDM table offset (see below) */
 #define  B43_PHY_OTABLENR		0xFC00	/* OFDM table number (see below) */
 #define  B43_PHY_OTABLENR_SHIFT		10
 #define B43_PHY_OTABLEI			B43_PHY_OFDM(0x73)	/* OFDM table data I */
 #define B43_PHY_OTABLEQ			B43_PHY_OFDM(0x74)	/* OFDM table data Q */
 #define B43_PHY_HPWR_TSSICTL		B43_PHY_OFDM(0x78)	/* Hardware power TSSI control */
 #define B43_PHY_ADCCTL			B43_PHY_OFDM(0x7A)	/* ADC control */
 #define B43_PHY_IDLE_TSSI		B43_PHY_OFDM(0x7B)
 #define B43_PHY_A_TEMP_SENSE		B43_PHY_OFDM(0x7C)	/* A PHY temperature sense */
 #define B43_PHY_NRSSITHRES		B43_PHY_OFDM(0x8A)	/* NRSSI threshold */
 #define B43_PHY_ANTWRSETT		B43_PHY_OFDM(0x8C)	/* Antenna WR settle */
 #define  B43_PHY_ANTWRSETT_ARXDIV	0x2000	/* Automatic RX diversity enabled */
 #define B43_PHY_CLIPPWRDOWNT		B43_PHY_OFDM(0x93)	/* Clip powerdown threshold */
 #define B43_PHY_OFDM9B			B43_PHY_OFDM(0x9B)	/* FIXME rename */
 #define B43_PHY_N1P1GAIN		B43_PHY_OFDM(0xA0)
 #define B43_PHY_P1P2GAIN		B43_PHY_OFDM(0xA1)
 #define B43_PHY_N1N2GAIN		B43_PHY_OFDM(0xA2)
 #define B43_PHY_CLIPTHRES		B43_PHY_OFDM(0xA3)
 #define B43_PHY_CLIPN1P2THRES		B43_PHY_OFDM(0xA4)
 #define B43_PHY_CCKSHIFTBITS_WA		B43_PHY_OFDM(0xA5)	/* CCK shiftbits workaround, FIXME rename */
 #define B43_PHY_CCKSHIFTBITS		B43_PHY_OFDM(0xA7)	/* FIXME rename */
 #define B43_PHY_DIVSRCHIDX		B43_PHY_OFDM(0xA8)	/* Divider search gain/index */
 #define B43_PHY_CLIPP2THRES		B43_PHY_OFDM(0xA9)
 #define B43_PHY_CLIPP3THRES		B43_PHY_OFDM(0xAA)
 #define B43_PHY_DIVP1P2GAIN		B43_PHY_OFDM(0xAB)
 #define B43_PHY_DIVSRCHGAINBACK		B43_PHY_OFDM(0xAD)	/* Divider search gain back */
 #define B43_PHY_DIVSRCHGAINCHNG		B43_PHY_OFDM(0xAE)	/* Divider search gain change */
 #define B43_PHY_CRSTHRES1		B43_PHY_OFDM(0xC0)	/* CRS Threshold 1 (phy.rev >= 2 only) */
 #define B43_PHY_CRSTHRES2		B43_PHY_OFDM(0xC1)	/* CRS Threshold 2 (phy.rev >= 2 only) */
 #define B43_PHY_TSSIP_LTBASE		B43_PHY_OFDM(0x380)	/* TSSI power lookup table base */
 #define B43_PHY_DC_LTBASE		B43_PHY_OFDM(0x3A0)	/* DC lookup table base */
 #define B43_PHY_GAIN_LTBASE		B43_PHY_OFDM(0x3C0)	/* Gain lookup table base */

 /*** OFDM table numbers ***/
 #define B43_OFDMTAB(number, offset)	(((number) << B43_PHY_OTABLENR_SHIFT) | (offset))
 #define B43_OFDMTAB_AGC1		B43_OFDMTAB(0x00, 0)
 #define B43_OFDMTAB_GAIN0		B43_OFDMTAB(0x00, 0)
 #define B43_OFDMTAB_GAINX		B43_OFDMTAB(0x01, 0)	//TODO rename
 #define B43_OFDMTAB_GAIN1		B43_OFDMTAB(0x01, 4)
 #define B43_OFDMTAB_AGC3		B43_OFDMTAB(0x02, 0)
 #define B43_OFDMTAB_GAIN2		B43_OFDMTAB(0x02, 3)
 #define B43_OFDMTAB_LNAHPFGAIN1		B43_OFDMTAB(0x03, 0)
 #define B43_OFDMTAB_WRSSI		B43_OFDMTAB(0x04, 0)
 #define B43_OFDMTAB_LNAHPFGAIN2		B43_OFDMTAB(0x04, 0)
 #define B43_OFDMTAB_NOISESCALE		B43_OFDMTAB(0x05, 0)
 #define B43_OFDMTAB_AGC2		B43_OFDMTAB(0x06, 0)
 #define B43_OFDMTAB_ROTOR		B43_OFDMTAB(0x08, 0)
 #define B43_OFDMTAB_ADVRETARD		B43_OFDMTAB(0x09, 0)
 #define B43_OFDMTAB_DAC			B43_OFDMTAB(0x0C, 0)
 #define B43_OFDMTAB_DC			B43_OFDMTAB(0x0E, 7)
 #define B43_OFDMTAB_PWRDYN2		B43_OFDMTAB(0x0E, 12)
 #define B43_OFDMTAB_LNAGAIN		B43_OFDMTAB(0x0E, 13)
 #define B43_OFDMTAB_UNKNOWN_0F		B43_OFDMTAB(0x0F, 0)	//TODO rename
 #define B43_OFDMTAB_UNKNOWN_APHY	B43_OFDMTAB(0x0F, 7)	//TODO rename
 #define B43_OFDMTAB_LPFGAIN		B43_OFDMTAB(0x0F, 12)
 #define B43_OFDMTAB_RSSI		B43_OFDMTAB(0x10, 0)
 #define B43_OFDMTAB_UNKNOWN_11		B43_OFDMTAB(0x11, 4)	//TODO rename
 #define B43_OFDMTAB_AGC1_R1		B43_OFDMTAB(0x13, 0)
 #define B43_OFDMTAB_GAINX_R1		B43_OFDMTAB(0x14, 0)	//TODO remove!
 #define B43_OFDMTAB_MINSIGSQ		B43_OFDMTAB(0x14, 0)
 #define B43_OFDMTAB_AGC3_R1		B43_OFDMTAB(0x15, 0)
 #define B43_OFDMTAB_WRSSI_R1		B43_OFDMTAB(0x15, 4)
 #define B43_OFDMTAB_TSSI		B43_OFDMTAB(0x15, 0)
 #define B43_OFDMTAB_DACRFPABB		B43_OFDMTAB(0x16, 0)
 #define B43_OFDMTAB_DACOFF		B43_OFDMTAB(0x17, 0)
 #define B43_OFDMTAB_DCBIAS		B43_OFDMTAB(0x18, 0)

 u16 b43_ofdmtab_read16(struct b43_wldev *dev, u16 table, u16 offset);
 void b43_ofdmtab_write16(struct b43_wldev *dev, u16 table,
 			 u16 offset, u16 value);
 u32 b43_ofdmtab_read32(struct b43_wldev *dev, u16 table, u16 offset);
 void b43_ofdmtab_write32(struct b43_wldev *dev, u16 table,
 			 u16 offset, u32 value);


 struct b43_phy_a {
 	bool initialised;

 	/* Pointer to the table used to convert a
 	 * TSSI value to dBm-Q5.2 */
 	const s8 *tssi2dbm;
 	/* Target idle TSSI */
 	int tgt_idle_tssi;
 	/* Current idle TSSI */
 	int cur_idle_tssi;//FIXME value currently not set

 	/* A-PHY TX Power control value. */
 	u16 txpwr_offset;

 	//TODO lots of missing stuff
 };

 /**
  * b43_phy_inita - Lowlevel A-PHY init routine.
  * This is _only_ used by the G-PHY code.
  */
 void b43_phy_inita(struct b43_wldev *dev);


 struct b43_phy_operations;
 extern const struct b43_phy_operations b43_phyops_a;

 #endif /* LINUX_B43_PHY_A_H_ */
	#ifndef LINUX_B43_PHY_A_H_
	#define LINUX_B43_PHY_A_H_

	#include "phy_common.h"


	/* OFDM (A) PHY Registers */
	#define B43_PHY_VERSION_OFDM B43_PHY_OFDM(0x00) /* Versioning register for A-PHY */
	#define B43_PHY_BBANDCFG B43_PHY_OFDM(0x01) /* Baseband config */
	#define B43_PHY_BBANDCFG_RXANT 0x180 /* RX Antenna selection */
	#define B43_PHY_BBANDCFG_RXANT_SHIFT 7
	#define B43_PHY_PWRDOWN B43_PHY_OFDM(0x03) /* Powerdown */
	#define B43_PHY_CRSTHRES1_R1 B43_PHY_OFDM(0x06) /* CRS Threshold 1 (phy.rev 1 only) */
	#define B43_PHY_LNAHPFCTL B43_PHY_OFDM(0x1C) /* LNA/HPF control */
	#define B43_PHY_LPFGAINCTL B43_PHY_OFDM(0x20) /* LPF Gain control */
	#define B43_PHY_ADIVRELATED B43_PHY_OFDM(0x27) /* FIXME rename */
	#define B43_PHY_CRS0 B43_PHY_OFDM(0x29)
	#define B43_PHY_CRS0_EN 0x4000
	#define B43_PHY_PEAK_COUNT B43_PHY_OFDM(0x30)
	#define B43_PHY_ANTDWELL B43_PHY_OFDM(0x2B) /* Antenna dwell */
	#define B43_PHY_ANTDWELL_AUTODIV1 0x0100 /* Automatic RX diversity start antenna */
	#define B43_PHY_ENCORE B43_PHY_OFDM(0x49) /* "Encore" (RangeMax / BroadRange) */
	#define B43_PHY_ENCORE_EN 0x0200 /* Encore enable */
	#define B43_PHY_LMS B43_PHY_OFDM(0x55)
	#define B43_PHY_OFDM61 B43_PHY_OFDM(0x61) /* FIXME rename */
	#define B43_PHY_OFDM61_10 0x0010 /* FIXME rename */
	#define B43_PHY_IQBAL B43_PHY_OFDM(0x69) /* I/Q balance */
	#define B43_PHY_BBTXDC_BIAS B43_PHY_OFDM(0x6B) /* Baseband TX DC bias */
	#define B43_PHY_OTABLECTL B43_PHY_OFDM(0x72) /* OFDM table control (see below) */
	#define B43_PHY_OTABLEOFF 0x03FF /* OFDM table offset (see below) */
	#define B43_PHY_OTABLENR 0xFC00 /* OFDM table number (see below) */
	#define B43_PHY_OTABLENR_SHIFT 10
	#define B43_PHY_OTABLEI B43_PHY_OFDM(0x73) /* OFDM table data I */
	#define B43_PHY_OTABLEQ B43_PHY_OFDM(0x74) /* OFDM table data Q */
	#define B43_PHY_HPWR_TSSICTL B43_PHY_OFDM(0x78) /* Hardware power TSSI control */
	#define B43_PHY_ADCCTL B43_PHY_OFDM(0x7A) /* ADC control */
	#define B43_PHY_IDLE_TSSI B43_PHY_OFDM(0x7B)
	#define B43_PHY_A_TEMP_SENSE B43_PHY_OFDM(0x7C) /* A PHY temperature sense */
	#define B43_PHY_NRSSITHRES B43_PHY_OFDM(0x8A) /* NRSSI threshold */
	#define B43_PHY_ANTWRSETT B43_PHY_OFDM(0x8C) /* Antenna WR settle */
	#define B43_PHY_ANTWRSETT_ARXDIV 0x2000 /* Automatic RX diversity enabled */
	#define B43_PHY_CLIPPWRDOWNT B43_PHY_OFDM(0x93) /* Clip powerdown threshold */
	#define B43_PHY_OFDM9B B43_PHY_OFDM(0x9B) /* FIXME rename */
	#define B43_PHY_N1P1GAIN B43_PHY_OFDM(0xA0)
	#define B43_PHY_P1P2GAIN B43_PHY_OFDM(0xA1)
	#define B43_PHY_N1N2GAIN B43_PHY_OFDM(0xA2)
	#define B43_PHY_CLIPTHRES B43_PHY_OFDM(0xA3)
	#define B43_PHY_CLIPN1P2THRES B43_PHY_OFDM(0xA4)
	#define B43_PHY_CCKSHIFTBITS_WA B43_PHY_OFDM(0xA5) /* CCK shiftbits workaround, FIXME rename */
	#define B43_PHY_CCKSHIFTBITS B43_PHY_OFDM(0xA7) /* FIXME rename */
	#define B43_PHY_DIVSRCHIDX B43_PHY_OFDM(0xA8) /* Divider search gain/index */
	#define B43_PHY_CLIPP2THRES B43_PHY_OFDM(0xA9)
	#define B43_PHY_CLIPP3THRES B43_PHY_OFDM(0xAA)
	#define B43_PHY_DIVP1P2GAIN B43_PHY_OFDM(0xAB)
	#define B43_PHY_DIVSRCHGAINBACK B43_PHY_OFDM(0xAD) /* Divider search gain back */
	#define B43_PHY_DIVSRCHGAINCHNG B43_PHY_OFDM(0xAE) /* Divider search gain change */
	#define B43_PHY_CRSTHRES1 B43_PHY_OFDM(0xC0) /* CRS Threshold 1 (phy.rev >= 2 only) */
	#define B43_PHY_CRSTHRES2 B43_PHY_OFDM(0xC1) /* CRS Threshold 2 (phy.rev >= 2 only) */
	#define B43_PHY_TSSIP_LTBASE B43_PHY_OFDM(0x380) /* TSSI power lookup table base */
	#define B43_PHY_DC_LTBASE B43_PHY_OFDM(0x3A0) /* DC lookup table base */
	#define B43_PHY_GAIN_LTBASE B43_PHY_OFDM(0x3C0) /* Gain lookup table base */

	/* OFDM table numbers */
	#define B43_OFDMTAB(number, offset) (((number) << B43_PHY_OTABLENR_SHIFT) \| (offset))
	#define B43_OFDMTAB_AGC1 B43_OFDMTAB(0x00, 0)
	#define B43_OFDMTAB_GAIN0 B43_OFDMTAB(0x00, 0)
	#define B43_OFDMTAB_GAINX B43_OFDMTAB(0x01, 0) //TODO rename
	#define B43_OFDMTAB_GAIN1 B43_OFDMTAB(0x01, 4)
	#define B43_OFDMTAB_AGC3 B43_OFDMTAB(0x02, 0)
	#define B43_OFDMTAB_GAIN2 B43_OFDMTAB(0x02, 3)
	#define B43_OFDMTAB_LNAHPFGAIN1 B43_OFDMTAB(0x03, 0)
	#define B43_OFDMTAB_WRSSI B43_OFDMTAB(0x04, 0)
	#define B43_OFDMTAB_LNAHPFGAIN2 B43_OFDMTAB(0x04, 0)
	#define B43_OFDMTAB_NOISESCALE B43_OFDMTAB(0x05, 0)
	#define B43_OFDMTAB_AGC2 B43_OFDMTAB(0x06, 0)
	#define B43_OFDMTAB_ROTOR B43_OFDMTAB(0x08, 0)
	#define B43_OFDMTAB_ADVRETARD B43_OFDMTAB(0x09, 0)
	#define B43_OFDMTAB_DAC B43_OFDMTAB(0x0C, 0)
	#define B43_OFDMTAB_DC B43_OFDMTAB(0x0E, 7)
	#define B43_OFDMTAB_PWRDYN2 B43_OFDMTAB(0x0E, 12)
	#define B43_OFDMTAB_LNAGAIN B43_OFDMTAB(0x0E, 13)
	#define B43_OFDMTAB_UNKNOWN_0F B43_OFDMTAB(0x0F, 0) //TODO rename
	#define B43_OFDMTAB_UNKNOWN_APHY B43_OFDMTAB(0x0F, 7) //TODO rename
	#define B43_OFDMTAB_LPFGAIN B43_OFDMTAB(0x0F, 12)
	#define B43_OFDMTAB_RSSI B43_OFDMTAB(0x10, 0)
	#define B43_OFDMTAB_UNKNOWN_11 B43_OFDMTAB(0x11, 4) //TODO rename
	#define B43_OFDMTAB_AGC1_R1 B43_OFDMTAB(0x13, 0)
	#define B43_OFDMTAB_GAINX_R1 B43_OFDMTAB(0x14, 0) //TODO remove!
	#define B43_OFDMTAB_MINSIGSQ B43_OFDMTAB(0x14, 0)
	#define B43_OFDMTAB_AGC3_R1 B43_OFDMTAB(0x15, 0)
	#define B43_OFDMTAB_WRSSI_R1 B43_OFDMTAB(0x15, 4)
	#define B43_OFDMTAB_TSSI B43_OFDMTAB(0x15, 0)
	#define B43_OFDMTAB_DACRFPABB B43_OFDMTAB(0x16, 0)
	#define B43_OFDMTAB_DACOFF B43_OFDMTAB(0x17, 0)
	#define B43_OFDMTAB_DCBIAS B43_OFDMTAB(0x18, 0)

	u16 b43_ofdmtab_read16(struct b43_wldev *dev, u16 table, u16 offset);
	void b43_ofdmtab_write16(struct b43_wldev *dev, u16 table,
	u16 offset, u16 value);
	u32 b43_ofdmtab_read32(struct b43_wldev *dev, u16 table, u16 offset);
	void b43_ofdmtab_write32(struct b43_wldev *dev, u16 table,
	u16 offset, u32 value);


	struct b43_phy_a {
	bool initialised;

	/* Pointer to the table used to convert a
	* TSSI value to dBm-Q5.2 */
	const s8 *tssi2dbm;
	/* Target idle TSSI */
	int tgt_idle_tssi;
	/* Current idle TSSI */
	int cur_idle_tssi;//FIXME value currently not set

	/* A-PHY TX Power control value. */
	u16 txpwr_offset;

	//TODO lots of missing stuff
	};

	/**
	* b43_phy_inita - Lowlevel A-PHY init routine.
	* This is _only_ used by the G-PHY code.
	*/
	void b43_phy_inita(struct b43_wldev *dev);


	struct b43_phy_operations;
	extern const struct b43_phy_operations b43_phyops_a;

	#endif /* LINUX_B43_PHY_A_H_ */