| #include <dt-bindings/clock/qcom,camcc-lagoon.h> |
| |
| &soc { |
| led_flash_triple_rear: qcom,camera-flash@4 { |
| cell-index = <4>; |
| reg = <0x04 0x00>; |
| compatible = "qcom,camera-flash"; |
| flash-source = <&pm6150l_flash0 &pm6150l_flash1>; |
| torch-source = <&pm6150l_torch0 &pm6150l_torch1>; |
| switch-source = <&pm6150l_switch2>; |
| }; |
| |
| led_flash_triple_rear_aux: qcom,camera-flash@5 { |
| cell-index = <5>; |
| reg = <0x05 0x00>; |
| compatible = "qcom,camera-flash"; |
| flash-source = <&pm6150l_flash0 &pm6150l_flash1>; |
| torch-source = <&pm6150l_torch0 &pm6150l_torch1>; |
| switch-source = <&pm6150l_switch2>; |
| }; |
| |
| led_flash_triple_rear_aux2: qcom,camera-flash@6 { |
| cell-index = <6>; |
| reg = <0x06 0x00>; |
| compatible = "qcom,camera-flash"; |
| flash-source = <&pm6150l_flash0 &pm6150l_flash1>; |
| torch-source = <&pm6150l_torch0 &pm6150l_torch1>; |
| switch-source = <&pm6150l_switch2>; |
| }; |
| |
| qcom,cam-res-mgr { |
| compatible = "qcom,cam-res-mgr"; |
| status = "ok"; |
| }; |
| }; |
| |
| &cam_cci0 { |
| actuator_triple_rear: qcom,actuator@4 { |
| cell-index = <4>; |
| reg = <0x4>; |
| compatible = "qcom,actuator"; |
| cci-device = <0>; |
| cci-master = <0>; |
| cam_vaf-supply = <&L5P>; |
| regulator-names = "cam_vaf"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <2800000>; |
| rgltr-max-voltage = <2800000>; |
| rgltr-load-current = <100000>; |
| status = "ok"; |
| }; |
| |
| actuator_triple_rear_aux: qcom,actuator@5 { |
| cell-index = <5>; |
| reg = <0x5>; |
| compatible = "qcom,actuator"; |
| cci-device = <0>; |
| cci-master = <1>; |
| cam_vaf-supply = <&L5P>; |
| regulator-names = "cam_vaf"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <2800000>; |
| rgltr-max-voltage = <2800000>; |
| rgltr-load-current = <100000>; |
| status = "ok"; |
| }; |
| |
| eeprom_triple_rear: qcom,eeprom@4 { |
| cell-index = <4>; |
| reg = <4>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L6P>; |
| cam_vana-supply = <&L4P>; |
| cam_vdig-supply = <&L2P>; |
| cam_clk-supply = <&cam_cc_titan_top_gdsc>; |
| cam_vaf-supply = <&L5P>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk", "cam_vaf"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <1800000 2904000 1104000 0 2800000>; |
| rgltr-max-voltage = <1800000 2904000 1104000 0 2800000>; |
| rgltr-load-current = <0 80000 105000 0 100000>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_active_rear>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_suspend_rear>; |
| gpios = <&tlmm 29 0>, |
| <&tlmm 34 0>, |
| <&tlmm 50 0>; |
| gpio-reset = <1>; |
| gpio-vana = <2>; |
| gpio-req-tbl-num = <0 1 2>; |
| gpio-req-tbl-flags = <1 0 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK4", |
| "CAM_RESET4", |
| "CAM_VANA4"; |
| sensor-mode = <0>; |
| cci-device = <0>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&camcc CAM_CC_MCLK0_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| |
| eeprom_triple_rear_aux: qcom,eeprom@5 { |
| cell-index = <5>; |
| reg = <5>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L6P>; |
| cam_vana-supply = <&L3P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&cam_cc_titan_top_gdsc>; |
| cam_vaf-supply = <&L5P>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk", "cam_vaf"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>; |
| rgltr-load-current = <0 2000000 105000 0 100000>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_active |
| &cam_sensor_active_rear_aux>; |
| pinctrl-1 = <&cam_sensor_mclk1_suspend |
| &cam_sensor_suspend_rear_aux>; |
| gpios = <&tlmm 30 0>, |
| <&tlmm 35 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK5", |
| "CAM_RESET5"; |
| sensor-mode = <0>; |
| cci-device = <0>; |
| cci-master = <1>; |
| status = "ok"; |
| clocks = <&camcc CAM_CC_MCLK1_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| |
| qcom,cam-sensor@4 { |
| cell-index = <4>; |
| compatible = "qcom,cam-sensor"; |
| reg = <0x4>; |
| csiphy-sd-index = <0>; |
| sensor-position-roll = <90>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <180>; |
| led-flash-src = <&led_flash_triple_rear>; |
| actuator-src = <&actuator_triple_rear>; |
| eeprom-src = <&eeprom_triple_rear>; |
| cam_vio-supply = <&L6P>; |
| cam_vana-supply = <&L4P>; |
| cam_vdig-supply = <&L2P>; |
| cam_clk-supply = <&cam_cc_titan_top_gdsc>; |
| cam_v_custom1-supply = <&S2A>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk", "cam_v_custom1"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2904000 1104000 0 1856000>; |
| rgltr-max-voltage = <1800000 2904000 1104000 0 2048000>; |
| rgltr-load-current = <0 80000 105000 0 80000>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_active_rear>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_suspend_rear>; |
| gpios = <&tlmm 29 0>, |
| <&tlmm 34 0>, |
| <&tlmm 50 0>; |
| gpio-reset = <1>; |
| gpio-vana = <2>; |
| gpio-req-tbl-num = <0 1 2>; |
| gpio-req-tbl-flags = <1 0 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK4", |
| "CAM_RESET4", |
| "CAM_VANA4"; |
| sensor-mode = <0>; |
| cci-device = <0>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&camcc CAM_CC_MCLK0_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| |
| qcom,cam-sensor@5 { |
| cell-index = <5>; |
| compatible = "qcom,cam-sensor"; |
| reg = <0x5>; |
| csiphy-sd-index = <1>; |
| sensor-position-roll = <90>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <180>; |
| led-flash-src = <&led_flash_triple_rear_aux>; |
| actuator-src = <&actuator_triple_rear_aux>; |
| eeprom-src = <&eeprom_triple_rear_aux>; |
| cam_vio-supply = <&L6P>; |
| cam_vana-supply = <&L3P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&cam_cc_titan_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1056000 0>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0>; |
| rgltr-load-current = <0 2000000 105000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_active |
| &cam_sensor_active_rear_aux>; |
| pinctrl-1 = <&cam_sensor_mclk1_suspend |
| &cam_sensor_suspend_rear_aux>; |
| gpios = <&tlmm 30 0>, |
| <&tlmm 35 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK5", |
| "CAM_RESET5"; |
| sensor-mode = <0>; |
| cci-device = <0>; |
| cci-master = <1>; |
| status = "ok"; |
| clocks = <&camcc CAM_CC_MCLK1_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| }; |
| |
| &cam_cci1 { |
| actuator_triple_rear_aux2: qcom,actuator@6 { |
| cell-index = <6>; |
| reg = <0x6>; |
| compatible = "qcom,actuator"; |
| cci-device = <1>; |
| cci-master = <0>; |
| cam_vaf-supply = <&L5P>; |
| regulator-names = "cam_vaf"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <2800000>; |
| rgltr-max-voltage = <2800000>; |
| rgltr-load-current = <100000>; |
| status = "ok"; |
| }; |
| |
| eeprom_front: qcom,eeprom@2 { |
| cell-index = <2>; |
| reg = <0x2>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L6P>; |
| cam_vana-supply = <&L3P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&cam_cc_titan_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <1800000 2800000 1056000 0>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0>; |
| rgltr-load-current = <0 80000 105000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk3_active |
| &cam_sensor_active_front>; |
| pinctrl-1 = <&cam_sensor_mclk3_suspend |
| &cam_sensor_suspend_front>; |
| gpios = <&tlmm 32 0>, |
| <&tlmm 37 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK3", |
| "CAM_RESET3"; |
| sensor-position = <1>; |
| sensor-mode = <0>; |
| cci-device = <1>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&camcc CAM_CC_MCLK3_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| |
| eeprom_triple_rear_aux2: qcom,eeprom@6 { |
| cell-index = <6>; |
| reg = <6>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L6P>; |
| cam_vana-supply = <&L7P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&cam_cc_titan_top_gdsc>; |
| cam_vaf-supply = <&L5P>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk", "cam_vaf"; |
| rgltr-cntrl-support; |
| rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>; |
| rgltr-load-current = <0 80000 105000 0 100000>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active |
| &cam_sensor_active_rear_aux2>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend |
| &cam_sensor_suspend_rear_aux2>; |
| gpios = <&tlmm 31 0>, |
| <&tlmm 36 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2"; |
| sensor-mode = <0>; |
| cci-device = <1>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&camcc CAM_CC_MCLK2_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| |
| qcom,cam-sensor@2 { |
| cell-index = <2>; |
| compatible = "qcom,cam-sensor"; |
| reg = <0x02>; |
| csiphy-sd-index = <3>; |
| sensor-position-roll = <270>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <0>; |
| eeprom-src = <&eeprom_front>; |
| cam_vio-supply = <&L6P>; |
| cam_vana-supply = <&L3P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&cam_cc_titan_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1056000 0>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0>; |
| rgltr-load-current = <0 80000 105000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk3_active |
| &cam_sensor_active_front>; |
| pinctrl-1 = <&cam_sensor_mclk3_suspend |
| &cam_sensor_suspend_front>; |
| gpios = <&tlmm 32 0>, |
| <&tlmm 37 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK3", |
| "CAM_RESET3"; |
| sensor-mode = <0>; |
| cci-device = <1>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&camcc CAM_CC_MCLK3_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| |
| qcom,cam-sensor@6 { |
| cell-index = <6>; |
| compatible = "qcom,cam-sensor"; |
| reg = <0x06>; |
| csiphy-sd-index = <2>; |
| sensor-position-roll = <90>; |
| sensor-position-pitch = <0>; |
| sensor-position-yaw = <180>; |
| led-flash-src = <&led_flash_triple_rear_aux2>; |
| actuator-src = <&actuator_triple_rear_aux2>; |
| eeprom-src = <&eeprom_triple_rear_aux2>; |
| cam_vio-supply = <&L6P>; |
| cam_vana-supply = <&L7P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&cam_cc_titan_top_gdsc>; |
| regulator-names = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| rgltr-cntrl-support; |
| pwm-switch; |
| rgltr-min-voltage = <1800000 2800000 1056000 0>; |
| rgltr-max-voltage = <1800000 2800000 1056000 0>; |
| rgltr-load-current = <0 80000 105000 0>; |
| gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active |
| &cam_sensor_active_rear_aux2>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend |
| &cam_sensor_suspend_rear_aux2>; |
| gpios = <&tlmm 31 0>, |
| <&tlmm 36 0>; |
| gpio-reset = <1>; |
| gpio-req-tbl-num = <0 1>; |
| gpio-req-tbl-flags = <1 0>; |
| gpio-req-tbl-label = "CAMIF_MCLK6", |
| "CAM_RESET6"; |
| sensor-mode = <0>; |
| cci-device = <1>; |
| cci-master = <0>; |
| status = "ok"; |
| clocks = <&camcc CAM_CC_MCLK2_CLK>; |
| clock-names = "cam_clk"; |
| clock-cntl-level = "turbo"; |
| clock-rates = <24000000>; |
| }; |
| }; |