| #include "khaje-pm7250b.dtsi" |
| #include "khaje-thermal-pm7250b-overlay.dtsi" |
| |
| &sde_dsi { |
| pinctrl-0 = <&sde_dsi_active &sde_te_active &disp_lcd_bias_en_default>; |
| }; |
| |
| &dsi_td4330_truly_v2_video { |
| qcom,platform-en-gpio = <&pm7250b_gpios 5 0>; |
| qcom,platform-bklight-en-gpio = <&pm7250b_gpios 1 0>; |
| }; |
| |
| &dsi_td4330_truly_v2_cmd { |
| qcom,platform-en-gpio = <&pm7250b_gpios 5 0>; |
| qcom,platform-bklight-en-gpio = <&pm7250b_gpios 1 0>; |
| }; |
| |
| &soc { |
| qrd_batterydata: qcom,battery-data { |
| qcom,batt-id-range-pct = <15>; |
| #include "qg-batterydata-atl466271_3300mAh.dtsi" |
| }; |
| }; |
| |
| &tlmm { |
| smb_int_default: smb_int_default { |
| mux { |
| pins = "gpio105"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio105"; |
| bias-pull-up; |
| input-enable; |
| }; |
| }; |
| }; |
| |
| &qupv3_se1_i2c { |
| status = "ok"; |
| #include "smb1394.dtsi" |
| }; |
| |
| &smb1394 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&smb_int_default>; |
| interrupt-parent = <&tlmm>; |
| interrupt-names = "smb1394"; |
| interrupts = <105 IRQ_TYPE_LEVEL_LOW>; |
| status = "ok"; |
| }; |
| |
| &smb1394_div2_cp_primary { |
| io-channels = <&pm7250b_vadc ADC_AMUX_THM2>; |
| io-channel-names = "die_temp"; |
| qcom,parallel-input-mode = <1>; |
| qcom,parallel-output-mode = <2>; |
| status = "ok"; |
| }; |
| |
| &pm7250b_vadc { |
| smb1390_therm@e { |
| qcom,scale-fn-type = <ADC_SCALE_HW_CALIB_PM5_SMB1398_TEMP>; |
| }; |
| }; |
| |
| &pm7250b_charger { |
| status = "ok"; |
| io-channels = <&pm7250b_vadc ADC_USB_IN_V_16>, |
| <&pm7250b_vadc ADC_USB_IN_I>, |
| <&pm7250b_vadc ADC_CHG_TEMP>, |
| <&pm7250b_vadc ADC_DIE_TEMP>, |
| <&pm7250b_vadc ADC_AMUX_THM3_PU2>, |
| <&pm7250b_vadc ADC_SBUx>, |
| <&pm7250b_vadc ADC_VPH_PWR>, |
| <&pm7250b_vadc ADC_AMUX_THM1_PU2>; |
| io-channel-names = "usb_in_voltage", |
| "usb_in_current", |
| "chg_temp", |
| "die_temp", |
| "conn_temp", |
| "sbux_res", |
| "vph_voltage", |
| "skin_temp"; |
| qcom,battery-data = <&qrd_batterydata>; |
| qcom,sec-charger-config = <1>; |
| qcom,auto-recharge-soc = <98>; |
| qcom,step-charging-enable; |
| qcom,sw-jeita-enable; |
| qcom,charger-temp-max = <800>; |
| qcom,smb-temp-max = <800>; |
| qcom,suspend-input-on-debug-batt; |
| qcom,fcc-stepping-enable; |
| qcom,fcc-step-delay-ms = <100>; |
| qcom,fcc-step-size-ua = <100000>; |
| qcom,smb-internal-pull-kohm = <0>; |
| qcom,thermal-mitigation = <8000000 7500000 7000000 6500000 6000000 5500000 |
| 5000000 4500000 4000000 3500000 3000000 2500000 2000000 1500000 |
| 1000000 500000>; |
| }; |
| |
| &pm7250b_qg { |
| status = "ok"; |
| io-channels = <&pm7250b_vadc ADC_BAT_THERM_PU2>, |
| <&pm7250b_vadc ADC_BAT_ID_PU2>; |
| io-channel-names = "batt-therm", |
| "batt-id"; |
| qcom,qg-iterm-ma = <150>; |
| qcom,hold-soc-while-full; |
| qcom,linearize-soc; |
| qcom,cl-feedback-on; |
| qcom,tcss-enable; |
| qcom,fvss-enable; |
| qcom,fvss-vbatt-mv = <3500>; |
| qcom,bass-enable; |
| qcom,vbatt-cutoff-mv = <3400>; |
| qcom,vbatt-low-mv = <3500>; |
| qcom,vbatt-low-cold-mv = <3800>; |
| qcom,vbatt-empty-mv = <3200>; |
| qcom,vbatt-empty-cold-mv = <3100>; |
| qcom,use-cp-iin-sns; |
| }; |
| |
| &cam_res_mgr_label { |
| gpios = <&pm7250b_gpios 4 0>; |
| }; |
| |
| &led_flash_rear { |
| gpios = <&pm7250b_gpios 4 0>; |
| }; |
| |
| &led_flash_rear_aux { |
| gpios = <&pm7250b_gpios 4 0>; |
| }; |
| |
| &led_flash_rear_aux2 { |
| gpios = <&pm7250b_gpios 4 0>; |
| }; |
| |
| &pm7250b_charger { |
| dpdm-supply = <&usb2_phy0>; |
| |
| smb5_vbus: qcom,smb5-vbus { |
| regulator-name = "smb5-vbus"; |
| }; |
| |
| smb5_vconn: qcom,smb5-vconn { |
| regulator-name = "smb5-vconn"; |
| }; |
| }; |
| |
| &pm7250b_pdphy { |
| vdd-pdphy-supply = <&L15A>; |
| vbus-supply = <&smb5_vbus>; |
| vconn-supply = <&smb5_vconn>; |
| }; |
| |
| &usb0 { |
| extcon = <&pm7250b_pdphy>, <&pm7250b_charger>, <&eud>; |
| }; |
| |
| &thermal_zones { |
| quiet-thermal-step { |
| cooling-maps { |
| quiet_batt_cdev1 { |
| trip = <&quiet_batt_trip0>; |
| cooling-device = <&pm7250b_charger 8 8>; |
| }; |
| |
| quiet_batt_cdev2 { |
| trip = <&quiet_batt_trip1>; |
| cooling-device = <&pm7250b_charger 12 12>; |
| }; |
| |
| quiet_batt_cdev3 { |
| trip = <&quiet_batt_trip2>; |
| cooling-device = <&pm7250b_charger 14 14>; |
| }; |
| |
| quiet_batt_cdev4 { |
| trip = <&quiet_batt_trip3>; |
| cooling-device = <&pm7250b_charger 16 16>; |
| }; |
| |
| quiet_batt_cdev5 { |
| trip = <&quiet_batt_trip4>; |
| cooling-device = <&pm7250b_charger 18 18>; |
| }; |
| }; |
| }; |
| }; |