| #include <dt-bindings/gpio/gpio.h> |
| #include "lito-audio-overlay.dtsi" |
| #include "lito-pmic-overlay.dtsi" |
| #include "camera/lito-camera-sensor-cdp.dtsi" |
| #include "lito-sde-display.dtsi" |
| #include "lito-thermal-overlay.dtsi" |
| |
| &soc { |
| gpio_keys { |
| compatible = "gpio-keys"; |
| label = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&key_vol_up_default>; |
| |
| vol_up { |
| label = "volume_up"; |
| gpios = <&pm8150l_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEUP>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| }; |
| |
| vdda_usb_ss_dp_core: vdda_usb_ss_dp_core { |
| compatible = "regulator-fixed"; |
| regulator-name = "vdd_supply"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <880000>; |
| enable-active-high; |
| gpio = <&pm8150l_gpios 12 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb_eldo13>; |
| }; |
| }; |
| |
| &usb_qmp_dp_phy { |
| vdd-supply = <&vdda_usb_ss_dp_core>; |
| }; |
| |
| &sde_dp { |
| vdda-0p9-supply = <&vdda_usb_ss_dp_core>; |
| }; |
| |
| &pm7250b_vadc { |
| pinctrl-0 = < |
| &bmr_w_therm_default |
| &camera_therm_default |
| &bmr_s_therm_default |
| >; |
| |
| bmr_s_therm { |
| reg = <ADC_GPIO3_PU2>; |
| label = "bmr_s_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| }; |
| |
| &pm7250b_gpios { |
| bmr_s_therm { |
| bmr_s_therm_default: bmr_s_therm_default { |
| pins = "gpio5"; |
| bias-high-impedance; |
| }; |
| }; |
| }; |
| |
| &pm7250b_adc_tm { |
| io-channels = <&pm7250b_vadc ADC_AMUX_THM1_PU2>, |
| <&pm7250b_vadc ADC_GPIO2_PU2>, |
| <&pm7250b_vadc ADC_GPIO3_PU2>, |
| <&pm7250b_vadc ADC_GPIO4_PU2>; |
| |
| bmr_s_therm@54 { |
| reg = <ADC_GPIO3_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| &thermal_zones { |
| mmw-pa4-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm7250b_adc_tm ADC_GPIO3_PU2>; |
| wake-capable-sensor; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |
| |
| &qupv3_se0_i2c { |
| status = "ok"; |
| qcom,clk-freq-out = <1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| nq@28 { |
| compatible = "qcom,nq-nci"; |
| reg = <0x28>; |
| qcom,nq-irq = <&tlmm 34 0x00>; |
| qcom,nq-ven = <&tlmm 12 0x00>; |
| qcom,nq-firm = <&tlmm 35 0x00>; |
| qcom,nq-clkreq = <&tlmm 31 0x00>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <34 0>; |
| interrupt-names = "nfc_irq"; |
| pinctrl-names = "nfc_active", "nfc_suspend"; |
| pinctrl-0 = <&nfc_int_active &nfc_enable_active |
| &nfc_clk_req_active>; |
| pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend |
| &nfc_clk_req_suspend>; |
| }; |
| }; |
| |
| &lito_snd { |
| qcom,model = "lito-cdp-snd-card"; |
| qcom,audio-routing = |
| "AMIC1", "MIC BIAS1", |
| "MIC BIAS1", "Analog Mic1", |
| "AMIC2", "MIC BIAS2", |
| "MIC BIAS2", "Analog Mic2", |
| "AMIC3", "MIC BIAS3", |
| "MIC BIAS3", "Analog Mic3", |
| "AMIC4", "MIC BIAS3", |
| "MIC BIAS3", "Analog Mic4", |
| "AMIC5", "MIC BIAS4", |
| "MIC BIAS4", "Analog Mic5", |
| "TX DMIC0", "MIC BIAS3", |
| "MIC BIAS3", "Digital Mic0", |
| "TX DMIC1", "MIC BIAS3", |
| "MIC BIAS3", "Digital Mic1", |
| "TX DMIC2", "MIC BIAS1", |
| "MIC BIAS1", "Digital Mic2", |
| "TX DMIC3", "MIC BIAS1", |
| "MIC BIAS1", "Digital Mic3", |
| "TX DMIC4", "MIC BIAS4", |
| "MIC BIAS4", "Digital Mic4", |
| "TX DMIC5", "MIC BIAS4", |
| "MIC BIAS4", "Digital Mic5", |
| "DMIC1", "MIC BIAS3", |
| "MIC BIAS3", "Digital Mic0", |
| "DMIC2", "MIC BIAS3", |
| "MIC BIAS3", "Digital Mic1", |
| "DMIC3", "MIC BIAS1", |
| "MIC BIAS1", "Digital Mic2", |
| "DMIC4", "MIC BIAS1", |
| "MIC BIAS1", "Digital Mic3", |
| "DMIC5", "MIC BIAS4", |
| "MIC BIAS4", "Digital Mic4", |
| "DMIC6", "MIC BIAS4", |
| "MIC BIAS4", "Digital Mic5", |
| "DMIC7", "MIC BIAS3", |
| "MIC BIAS3", "Digital Mic6", |
| "DMIC8", "MIC BIAS3", |
| "MIC BIAS3", "Digital Mic7", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "IN3_AUX", "AUX_OUT", |
| "TX SWR_ADC0", "ADC1_OUTPUT", |
| "TX SWR_ADC1", "ADC2_OUTPUT", |
| "TX SWR_ADC2", "ADC3_OUTPUT", |
| "TX SWR_ADC3", "ADC4_OUTPUT", |
| "TX SWR_DMIC0", "DMIC1_OUTPUT", |
| "TX SWR_DMIC1", "DMIC2_OUTPUT", |
| "TX SWR_DMIC2", "DMIC3_OUTPUT", |
| "TX SWR_DMIC3", "DMIC4_OUTPUT", |
| "TX SWR_DMIC4", "DMIC5_OUTPUT", |
| "TX SWR_DMIC5", "DMIC6_OUTPUT", |
| "TX SWR_DMIC6", "DMIC7_OUTPUT", |
| "TX SWR_DMIC7", "DMIC8_OUTPUT", |
| "WSA SRC0_INP", "SRC0", |
| "WSA_TX DEC0_INP", "TX DEC0 MUX", |
| "WSA_TX DEC1_INP", "TX DEC1 MUX", |
| "RX_TX DEC0_INP", "TX DEC0 MUX", |
| "RX_TX DEC1_INP", "TX DEC1 MUX", |
| "RX_TX DEC2_INP", "TX DEC2 MUX", |
| "RX_TX DEC3_INP", "TX DEC3 MUX", |
| "SpkrLeft IN", "WSA_SPK1 OUT", |
| "SpkrRight IN", "WSA_SPK2 OUT", |
| "VA_AIF1 CAP", "VA_SWR_CLK", |
| "VA_AIF2 CAP", "VA_SWR_CLK", |
| "VA_AIF3 CAP", "VA_SWR_CLK", |
| "VA MIC BIAS3", "Digital Mic0", |
| "VA MIC BIAS3", "Digital Mic1", |
| "VA MIC BIAS1", "Digital Mic2", |
| "VA MIC BIAS1", "Digital Mic3", |
| "VA MIC BIAS4", "Digital Mic4", |
| "VA MIC BIAS4", "Digital Mic5", |
| "VA DMIC0", "VA MIC BIAS3", |
| "VA DMIC1", "VA MIC BIAS3", |
| "VA DMIC2", "VA MIC BIAS1", |
| "VA DMIC3", "VA MIC BIAS1", |
| "VA DMIC4", "VA MIC BIAS4", |
| "VA DMIC5", "VA MIC BIAS4", |
| "VA SWR_ADC0", "VA_SWR_CLK", |
| "VA SWR_ADC1", "VA_SWR_CLK", |
| "VA SWR_ADC2", "VA_SWR_CLK", |
| "VA SWR_ADC3", "VA_SWR_CLK", |
| "VA SWR_MIC0", "VA_SWR_CLK", |
| "VA SWR_MIC1", "VA_SWR_CLK", |
| "VA SWR_MIC2", "VA_SWR_CLK", |
| "VA SWR_MIC3", "VA_SWR_CLK", |
| "VA SWR_MIC4", "VA_SWR_CLK", |
| "VA SWR_MIC5", "VA_SWR_CLK", |
| "VA SWR_MIC6", "VA_SWR_CLK", |
| "VA SWR_MIC7", "VA_SWR_CLK", |
| "VA SWR_ADC0", "ADC1_OUTPUT", |
| "VA SWR_ADC1", "ADC2_OUTPUT", |
| "VA SWR_ADC2", "ADC3_OUTPUT", |
| "VA SWR_ADC3", "ADC4_OUTPUT", |
| "VA SWR_MIC0", "DMIC1_OUTPUT", |
| "VA SWR_MIC1", "DMIC2_OUTPUT", |
| "VA SWR_MIC2", "DMIC3_OUTPUT", |
| "VA SWR_MIC3", "DMIC4_OUTPUT", |
| "VA SWR_MIC4", "DMIC5_OUTPUT", |
| "VA SWR_MIC5", "DMIC6_OUTPUT", |
| "VA SWR_MIC6", "DMIC7_OUTPUT", |
| "VA SWR_MIC7", "DMIC8_OUTPUT"; |
| }; |
| |
| &ufsphy_mem { |
| compatible = "qcom,ufs-phy-qmp-v4-lito"; |
| |
| vdda-phy-supply = <&pm8150_l5>; |
| vdda-pll-supply = <&pm8150_l9>; |
| vdda-phy-max-microamp = <90200>; |
| vdda-pll-max-microamp = <19000>; |
| |
| status = "ok"; |
| }; |
| |
| &ufshc_mem { |
| vdd-hba-supply = <&ufs_phy_gdsc>; |
| vdd-hba-fixed-regulator; |
| vcc-supply = <&pm8150a_l7>; |
| vcc-voltage-level = <2950000 2960000>; |
| vccq2-supply = <&pm8150_s4>; |
| vcc-max-microamp = <800000>; |
| vccq2-max-microamp = <800000>; |
| vccq2-min-microamp = <0>; |
| |
| qcom,vddp-ref-clk-supply = <&pm8150_l9>; |
| qcom,vddp-ref-clk-max-microamp = <100>; |
| qcom,vddp-ref-clk-min-microamp = <0>; |
| qcom,vddp-ref-clk-min-uV = <1152000>; |
| qcom,vddp-ref-clk-max-uV = <1200000>; |
| status = "ok"; |
| }; |
| |
| &sdhc_1 { |
| vdd-supply = <&pm8150a_l7>; |
| qcom,vdd-voltage-level = <2950000 2950000>; |
| qcom,vdd-current-level = <0 570000>; |
| |
| vdd-io-supply = <&pm8150_s4>; |
| qcom,vdd-io-always-on; |
| qcom,vdd-io-lpm-sup; |
| qcom,vdd-io-voltage-level = <1800000 1800000>; |
| qcom,vdd-io-current-level = <0 325000>; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on |
| &sdc1_rclk_on>; |
| pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off |
| &sdc1_rclk_off>; |
| |
| status = "ok"; |
| }; |
| |
| &sdhc_2 { |
| vdd-supply = <&pm8150a_l9>; |
| qcom,vdd-voltage-level = <2950000 2950000>; |
| qcom,vdd-current-level = <0 800000>; |
| |
| vdd-io-supply = <&pm8150a_l6>; |
| qcom,vdd-io-voltage-level = <1800000 2950000>; |
| qcom,vdd-io-current-level = <0 22000>; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; |
| |
| cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; |
| |
| status = "ok"; |
| }; |
| |
| &pm8150a_amoled { |
| status = "ok"; |
| }; |
| |
| &pm7250b_charger { |
| status = "ok"; |
| io-channels = <&pm7250b_vadc ADC_USB_IN_V_16>, |
| <&pm7250b_vadc ADC_USB_IN_I>, |
| <&pm7250b_vadc ADC_CHG_TEMP>, |
| <&pm7250b_vadc ADC_DIE_TEMP>, |
| <&pm7250b_vadc ADC_AMUX_THM3_PU2>, |
| <&pm7250b_vadc ADC_SBUx>, |
| <&pm7250b_vadc ADC_VPH_PWR>; |
| io-channel-names = "usb_in_voltage", |
| "usb_in_current", |
| "chg_temp", |
| "die_temp", |
| "conn_temp", |
| "sbux_res", |
| "vph_voltage"; |
| qcom,batteryless-platform; |
| qcom,sec-charger-config = <1>; |
| qcom,auto-recharge-soc = <98>; |
| qcom,step-charging-enable; |
| qcom,sw-jeita-enable; |
| qcom,charger-temp-max = <800>; |
| qcom,smb-temp-max = <800>; |
| qcom,suspend-input-on-debug-batt; |
| }; |
| |
| &pm7250b_qg { |
| status = "ok"; |
| io-channels = <&pm7250b_vadc ADC_BAT_THERM_PU2>, |
| <&pm7250b_vadc ADC_BAT_ID_PU2>; |
| io-channel-names = "batt-therm", |
| "batt-id"; |
| qcom,qg-iterm-ma = <100>; |
| qcom,hold-soc-while-full; |
| qcom,linearize-soc; |
| qcom,cl-feedback-on; |
| }; |
| |
| &qupv3_se7_i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "ok"; |
| qcom,i2c-touch-active = "st,fts"; |
| |
| st_fts@49 { |
| compatible = "st,fts"; |
| reg = <0x49>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <9 0x2008>; |
| vdd-supply = <&pm8150_s4>; |
| avdd-supply = <&pm8150_l13>; |
| pinctrl-names = "pmx_ts_active", "pmx_ts_suspend"; |
| pinctrl-0 = <&ts_active>; |
| pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>; |
| st,irq-gpio = <&tlmm 9 0x2008>; |
| st,reset-gpio = <&tlmm 8 0x00>; |
| st,regulator_dvdd = "vdd"; |
| st,regulator_avdd = "avdd"; |
| panel = <&dsi_sw43404_amoled_cmd &dsi_sw43404_amoled_video |
| &dsi_sw43404_amoled_fhd_plus_cmd>; |
| }; |
| |
| synaptics_dsx@22 { |
| compatible = "synaptics,dsx-i2c"; |
| reg = <0x22>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <39 0x2008>; |
| vdd-supply = <&pm8150_s4>; |
| avdd-supply = <&pm8150_l13>; |
| pinctrl-names = "pmx_ts_active", "pmx_ts_suspend", |
| "pmx_ts_release"; |
| pinctrl-0 = <&ts_active>; |
| pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>; |
| pinctrl-2 = <&pmx_ts_release>; |
| synaptics,pwr-reg-name = "avdd"; |
| synaptics,bus-reg-name = "vdd"; |
| synaptics,ub-i2c-addr = <0x22>; |
| synaptics,max-y-for-2d = <1859>; |
| synaptics,irq-gpio = <&tlmm 9 0x2008>; |
| synaptics,reset-gpio = <&tlmm 8 0x0>; |
| synaptics,irq-on-state = <0>; |
| synaptics,power-delay-ms = <200>; |
| synaptics,reset-delay-ms = <200>; |
| synaptics,reset-on-state = <0>; |
| synaptics,reset-active-ms = <20>; |
| |
| panel = <&dsi_sharp_qsync_wqhd_cmd &dsi_sharp_qsync_wqhd_video |
| &dsi_sharp_qsync_fhd_video &dsi_sharp_qsync_fhd_cmd>; |
| }; |
| |
| focaltech@38 { |
| compatible = "focaltech,fts_ts"; |
| reg = <0x38>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <39 0x2008>; |
| focaltech,irq-gpio = <&tlmm 9 0x2008>; |
| focaltech,reset-gpio = <&tlmm 8 0x00>; |
| focaltech,max-touch-number = <5>; |
| focaltech,display-coords = <0 0 1080 2340>; |
| |
| vdd-supply = <&pm8150_l13>; |
| |
| pinctrl-names = "pmx_ts_active", "pmx_ts_suspend", |
| "pmx_ts_release"; |
| pinctrl-0 = <&ts_active>; |
| pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>; |
| pinctrl-2 = <&pmx_ts_release>; |
| |
| panel = <&dsi_r66451_amoled_144hz_cmd>; |
| }; |
| |
| }; |
| |
| &dsi_sw43404_amoled_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| }; |
| |
| &dsi_sw43404_amoled_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| }; |
| |
| &dsi_sw43404_amoled_fhd_plus_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| }; |
| |
| &dsi_dual_sharp_wqhd_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_dual_sharp_wqhd_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_sharp_4k_dsc_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_sharp_4k_dsc_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_nt35695b_truly_fhd_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,panel-sec-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-sec-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-sec-reset-gpio = <&pm8150l_gpios 11 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_nt35695b_truly_fhd_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,panel-sec-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-sec-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-sec-reset-gpio = <&pm8150l_gpios 11 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_sharp_qsync_wqhd_video { |
| qcom,esd-check-enabled; |
| qcom,mdss-dsi-panel-status-check-mode = "reg_read"; |
| qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a]; |
| qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode"; |
| qcom,mdss-dsi-panel-status-value = <0x9c>; |
| qcom,mdss-dsi-panel-status-read-length = <1>; |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_sharp_qsync_wqhd_cmd { |
| qcom,esd-check-enabled; |
| qcom,mdss-dsi-panel-status-check-mode = "reg_read"; |
| qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a]; |
| qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode"; |
| qcom,mdss-dsi-panel-status-value = <0x9c>; |
| qcom,mdss-dsi-panel-status-read-length = <1>; |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_sharp_qsync_fhd_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| }; |
| |
| &dsi_sharp_qsync_fhd_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_no_labibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| qcom,platform-en-gpio = <&pm8150l_gpios 9 0>; |
| qcom,platform-bklight-en-gpio = <&pm8150l_gpios 10 0>; |
| |
| }; |
| |
| &dsi_rm69299_visionox_amoled_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <255>; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| }; |
| |
| &dsi_r66451_amoled_144hz_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,mdss-dsi-bl-inverted-dbv; |
| qcom,platform-te-gpio = <&tlmm 10 0>; |
| qcom,platform-reset-gpio = <&pm8150l_gpios 3 0>; |
| }; |
| |
| &sde_dsi { |
| qcom,dsi-default-panel = <&dsi_sw43404_amoled_video>; |
| }; |
| |