| /* |
| * Cherryview/Braswell pinctrl driver |
| * |
| * Copyright (C) 2014, Intel Corporation |
| * Author: Mika Westerberg <mika.westerberg@linux.intel.com> |
| * |
| * This driver is based on the original Cherryview GPIO driver by |
| * Ning Li <ning.li@intel.com> |
| * Alan Cox <alan@linux.intel.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <linux/dmi.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/types.h> |
| #include <linux/gpio.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/acpi.h> |
| #include <linux/pinctrl/pinctrl.h> |
| #include <linux/pinctrl/pinmux.h> |
| #include <linux/pinctrl/pinconf.h> |
| #include <linux/pinctrl/pinconf-generic.h> |
| #include <linux/platform_device.h> |
| |
| #define CHV_INTSTAT 0x300 |
| #define CHV_INTMASK 0x380 |
| |
| #define FAMILY_PAD_REGS_OFF 0x4400 |
| #define FAMILY_PAD_REGS_SIZE 0x400 |
| #define MAX_FAMILY_PAD_GPIO_NO 15 |
| #define GPIO_REGS_SIZE 8 |
| |
| #define CHV_PADCTRL0 0x000 |
| #define CHV_PADCTRL0_INTSEL_SHIFT 28 |
| #define CHV_PADCTRL0_INTSEL_MASK (0xf << CHV_PADCTRL0_INTSEL_SHIFT) |
| #define CHV_PADCTRL0_TERM_UP BIT(23) |
| #define CHV_PADCTRL0_TERM_SHIFT 20 |
| #define CHV_PADCTRL0_TERM_MASK (7 << CHV_PADCTRL0_TERM_SHIFT) |
| #define CHV_PADCTRL0_TERM_20K 1 |
| #define CHV_PADCTRL0_TERM_5K 2 |
| #define CHV_PADCTRL0_TERM_1K 4 |
| #define CHV_PADCTRL0_PMODE_SHIFT 16 |
| #define CHV_PADCTRL0_PMODE_MASK (0xf << CHV_PADCTRL0_PMODE_SHIFT) |
| #define CHV_PADCTRL0_GPIOEN BIT(15) |
| #define CHV_PADCTRL0_GPIOCFG_SHIFT 8 |
| #define CHV_PADCTRL0_GPIOCFG_MASK (7 << CHV_PADCTRL0_GPIOCFG_SHIFT) |
| #define CHV_PADCTRL0_GPIOCFG_GPIO 0 |
| #define CHV_PADCTRL0_GPIOCFG_GPO 1 |
| #define CHV_PADCTRL0_GPIOCFG_GPI 2 |
| #define CHV_PADCTRL0_GPIOCFG_HIZ 3 |
| #define CHV_PADCTRL0_GPIOTXSTATE BIT(1) |
| #define CHV_PADCTRL0_GPIORXSTATE BIT(0) |
| |
| #define CHV_PADCTRL1 0x004 |
| #define CHV_PADCTRL1_CFGLOCK BIT(31) |
| #define CHV_PADCTRL1_INVRXTX_SHIFT 4 |
| #define CHV_PADCTRL1_INVRXTX_MASK (0xf << CHV_PADCTRL1_INVRXTX_SHIFT) |
| #define CHV_PADCTRL1_INVRXTX_TXENABLE (2 << CHV_PADCTRL1_INVRXTX_SHIFT) |
| #define CHV_PADCTRL1_ODEN BIT(3) |
| #define CHV_PADCTRL1_INVRXTX_RXDATA (4 << CHV_PADCTRL1_INVRXTX_SHIFT) |
| #define CHV_PADCTRL1_INTWAKECFG_MASK 7 |
| #define CHV_PADCTRL1_INTWAKECFG_FALLING 1 |
| #define CHV_PADCTRL1_INTWAKECFG_RISING 2 |
| #define CHV_PADCTRL1_INTWAKECFG_BOTH 3 |
| #define CHV_PADCTRL1_INTWAKECFG_LEVEL 4 |
| |
| /** |
| * struct chv_alternate_function - A per group or per pin alternate function |
| * @pin: Pin number (only used in per pin configs) |
| * @mode: Mode the pin should be set in |
| * @invert_oe: Invert OE for this pin |
| */ |
| struct chv_alternate_function { |
| unsigned pin; |
| u8 mode; |
| bool invert_oe; |
| }; |
| |
| /** |
| * struct chv_pincgroup - describes a CHV pin group |
| * @name: Name of the group |
| * @pins: An array of pins in this group |
| * @npins: Number of pins in this group |
| * @altfunc: Alternate function applied to all pins in this group |
| * @overrides: Alternate function override per pin or %NULL if not used |
| * @noverrides: Number of per pin alternate function overrides if |
| * @overrides != NULL. |
| */ |
| struct chv_pingroup { |
| const char *name; |
| const unsigned *pins; |
| size_t npins; |
| struct chv_alternate_function altfunc; |
| const struct chv_alternate_function *overrides; |
| size_t noverrides; |
| }; |
| |
| /** |
| * struct chv_function - A CHV pinmux function |
| * @name: Name of the function |
| * @groups: An array of groups for this function |
| * @ngroups: Number of groups in @groups |
| */ |
| struct chv_function { |
| const char *name; |
| const char * const *groups; |
| size_t ngroups; |
| }; |
| |
| /** |
| * struct chv_gpio_pinrange - A range of pins that can be used as GPIOs |
| * @base: Start pin number |
| * @npins: Number of pins in this range |
| */ |
| struct chv_gpio_pinrange { |
| unsigned base; |
| unsigned npins; |
| }; |
| |
| /** |
| * struct chv_community - A community specific configuration |
| * @uid: ACPI _UID used to match the community |
| * @pins: All pins in this community |
| * @npins: Number of pins |
| * @groups: All groups in this community |
| * @ngroups: Number of groups |
| * @functions: All functions in this community |
| * @nfunctions: Number of functions |
| * @gpio_ranges: An array of GPIO ranges in this community |
| * @ngpio_ranges: Number of GPIO ranges |
| * @nirqs: Total number of IRQs this community can generate |
| */ |
| struct chv_community { |
| const char *uid; |
| const struct pinctrl_pin_desc *pins; |
| size_t npins; |
| const struct chv_pingroup *groups; |
| size_t ngroups; |
| const struct chv_function *functions; |
| size_t nfunctions; |
| const struct chv_gpio_pinrange *gpio_ranges; |
| size_t ngpio_ranges; |
| size_t nirqs; |
| acpi_adr_space_type acpi_space_id; |
| }; |
| |
| struct chv_pin_context { |
| u32 padctrl0; |
| u32 padctrl1; |
| }; |
| |
| /** |
| * struct chv_pinctrl - CHV pinctrl private structure |
| * @dev: Pointer to the parent device |
| * @pctldesc: Pin controller description |
| * @pctldev: Pointer to the pin controller device |
| * @chip: GPIO chip in this pin controller |
| * @regs: MMIO registers |
| * @intr_lines: Stores mapping between 16 HW interrupt wires and GPIO |
| * offset (in GPIO number space) |
| * @community: Community this pinctrl instance represents |
| * |
| * The first group in @groups is expected to contain all pins that can be |
| * used as GPIOs. |
| */ |
| struct chv_pinctrl { |
| struct device *dev; |
| struct pinctrl_desc pctldesc; |
| struct pinctrl_dev *pctldev; |
| struct gpio_chip chip; |
| void __iomem *regs; |
| unsigned intr_lines[16]; |
| const struct chv_community *community; |
| u32 saved_intmask; |
| struct chv_pin_context *saved_pin_context; |
| }; |
| |
| #define ALTERNATE_FUNCTION(p, m, i) \ |
| { \ |
| .pin = (p), \ |
| .mode = (m), \ |
| .invert_oe = (i), \ |
| } |
| |
| #define PIN_GROUP(n, p, m, i) \ |
| { \ |
| .name = (n), \ |
| .pins = (p), \ |
| .npins = ARRAY_SIZE((p)), \ |
| .altfunc.mode = (m), \ |
| .altfunc.invert_oe = (i), \ |
| } |
| |
| #define PIN_GROUP_WITH_OVERRIDE(n, p, m, i, o) \ |
| { \ |
| .name = (n), \ |
| .pins = (p), \ |
| .npins = ARRAY_SIZE((p)), \ |
| .altfunc.mode = (m), \ |
| .altfunc.invert_oe = (i), \ |
| .overrides = (o), \ |
| .noverrides = ARRAY_SIZE((o)), \ |
| } |
| |
| #define FUNCTION(n, g) \ |
| { \ |
| .name = (n), \ |
| .groups = (g), \ |
| .ngroups = ARRAY_SIZE((g)), \ |
| } |
| |
| #define GPIO_PINRANGE(start, end) \ |
| { \ |
| .base = (start), \ |
| .npins = (end) - (start) + 1, \ |
| } |
| |
| static const struct pinctrl_pin_desc southwest_pins[] = { |
| PINCTRL_PIN(0, "FST_SPI_D2"), |
| PINCTRL_PIN(1, "FST_SPI_D0"), |
| PINCTRL_PIN(2, "FST_SPI_CLK"), |
| PINCTRL_PIN(3, "FST_SPI_D3"), |
| PINCTRL_PIN(4, "FST_SPI_CS1_B"), |
| PINCTRL_PIN(5, "FST_SPI_D1"), |
| PINCTRL_PIN(6, "FST_SPI_CS0_B"), |
| PINCTRL_PIN(7, "FST_SPI_CS2_B"), |
| |
| PINCTRL_PIN(15, "UART1_RTS_B"), |
| PINCTRL_PIN(16, "UART1_RXD"), |
| PINCTRL_PIN(17, "UART2_RXD"), |
| PINCTRL_PIN(18, "UART1_CTS_B"), |
| PINCTRL_PIN(19, "UART2_RTS_B"), |
| PINCTRL_PIN(20, "UART1_TXD"), |
| PINCTRL_PIN(21, "UART2_TXD"), |
| PINCTRL_PIN(22, "UART2_CTS_B"), |
| |
| PINCTRL_PIN(30, "MF_HDA_CLK"), |
| PINCTRL_PIN(31, "MF_HDA_RSTB"), |
| PINCTRL_PIN(32, "MF_HDA_SDIO"), |
| PINCTRL_PIN(33, "MF_HDA_SDO"), |
| PINCTRL_PIN(34, "MF_HDA_DOCKRSTB"), |
| PINCTRL_PIN(35, "MF_HDA_SYNC"), |
| PINCTRL_PIN(36, "MF_HDA_SDI1"), |
| PINCTRL_PIN(37, "MF_HDA_DOCKENB"), |
| |
| PINCTRL_PIN(45, "I2C5_SDA"), |
| PINCTRL_PIN(46, "I2C4_SDA"), |
| PINCTRL_PIN(47, "I2C6_SDA"), |
| PINCTRL_PIN(48, "I2C5_SCL"), |
| PINCTRL_PIN(49, "I2C_NFC_SDA"), |
| PINCTRL_PIN(50, "I2C4_SCL"), |
| PINCTRL_PIN(51, "I2C6_SCL"), |
| PINCTRL_PIN(52, "I2C_NFC_SCL"), |
| |
| PINCTRL_PIN(60, "I2C1_SDA"), |
| PINCTRL_PIN(61, "I2C0_SDA"), |
| PINCTRL_PIN(62, "I2C2_SDA"), |
| PINCTRL_PIN(63, "I2C1_SCL"), |
| PINCTRL_PIN(64, "I2C3_SDA"), |
| PINCTRL_PIN(65, "I2C0_SCL"), |
| PINCTRL_PIN(66, "I2C2_SCL"), |
| PINCTRL_PIN(67, "I2C3_SCL"), |
| |
| PINCTRL_PIN(75, "SATA_GP0"), |
| PINCTRL_PIN(76, "SATA_GP1"), |
| PINCTRL_PIN(77, "SATA_LEDN"), |
| PINCTRL_PIN(78, "SATA_GP2"), |
| PINCTRL_PIN(79, "MF_SMB_ALERTB"), |
| PINCTRL_PIN(80, "SATA_GP3"), |
| PINCTRL_PIN(81, "MF_SMB_CLK"), |
| PINCTRL_PIN(82, "MF_SMB_DATA"), |
| |
| PINCTRL_PIN(90, "PCIE_CLKREQ0B"), |
| PINCTRL_PIN(91, "PCIE_CLKREQ1B"), |
| PINCTRL_PIN(92, "GP_SSP_2_CLK"), |
| PINCTRL_PIN(93, "PCIE_CLKREQ2B"), |
| PINCTRL_PIN(94, "GP_SSP_2_RXD"), |
| PINCTRL_PIN(95, "PCIE_CLKREQ3B"), |
| PINCTRL_PIN(96, "GP_SSP_2_FS"), |
| PINCTRL_PIN(97, "GP_SSP_2_TXD"), |
| }; |
| |
| static const unsigned southwest_fspi_pins[] = { 0, 1, 2, 3, 4, 5, 6, 7 }; |
| static const unsigned southwest_uart0_pins[] = { 16, 20 }; |
| static const unsigned southwest_uart1_pins[] = { 15, 16, 18, 20 }; |
| static const unsigned southwest_uart2_pins[] = { 17, 19, 21, 22 }; |
| static const unsigned southwest_i2c0_pins[] = { 61, 65 }; |
| static const unsigned southwest_hda_pins[] = { 30, 31, 32, 33, 34, 35, 36, 37 }; |
| static const unsigned southwest_lpe_pins[] = { |
| 30, 31, 32, 33, 34, 35, 36, 37, 92, 94, 96, 97, |
| }; |
| static const unsigned southwest_i2c1_pins[] = { 60, 63 }; |
| static const unsigned southwest_i2c2_pins[] = { 62, 66 }; |
| static const unsigned southwest_i2c3_pins[] = { 64, 67 }; |
| static const unsigned southwest_i2c4_pins[] = { 46, 50 }; |
| static const unsigned southwest_i2c5_pins[] = { 45, 48 }; |
| static const unsigned southwest_i2c6_pins[] = { 47, 51 }; |
| static const unsigned southwest_i2c_nfc_pins[] = { 49, 52 }; |
| static const unsigned southwest_smbus_pins[] = { 79, 81, 82 }; |
| static const unsigned southwest_spi3_pins[] = { 76, 79, 80, 81, 82 }; |
| |
| /* LPE I2S TXD pins need to have invert_oe set */ |
| static const struct chv_alternate_function southwest_lpe_altfuncs[] = { |
| ALTERNATE_FUNCTION(30, 1, true), |
| ALTERNATE_FUNCTION(34, 1, true), |
| ALTERNATE_FUNCTION(97, 1, true), |
| }; |
| |
| /* |
| * Two spi3 chipselects are available in different mode than the main spi3 |
| * functionality, which is using mode 1. |
| */ |
| static const struct chv_alternate_function southwest_spi3_altfuncs[] = { |
| ALTERNATE_FUNCTION(76, 3, false), |
| ALTERNATE_FUNCTION(80, 3, false), |
| }; |
| |
| static const struct chv_pingroup southwest_groups[] = { |
| PIN_GROUP("uart0_grp", southwest_uart0_pins, 2, false), |
| PIN_GROUP("uart1_grp", southwest_uart1_pins, 1, false), |
| PIN_GROUP("uart2_grp", southwest_uart2_pins, 1, false), |
| PIN_GROUP("hda_grp", southwest_hda_pins, 2, false), |
| PIN_GROUP("i2c0_grp", southwest_i2c0_pins, 1, true), |
| PIN_GROUP("i2c1_grp", southwest_i2c1_pins, 1, true), |
| PIN_GROUP("i2c2_grp", southwest_i2c2_pins, 1, true), |
| PIN_GROUP("i2c3_grp", southwest_i2c3_pins, 1, true), |
| PIN_GROUP("i2c4_grp", southwest_i2c4_pins, 1, true), |
| PIN_GROUP("i2c5_grp", southwest_i2c5_pins, 1, true), |
| PIN_GROUP("i2c6_grp", southwest_i2c6_pins, 1, true), |
| PIN_GROUP("i2c_nfc_grp", southwest_i2c_nfc_pins, 2, true), |
| |
| PIN_GROUP_WITH_OVERRIDE("lpe_grp", southwest_lpe_pins, 1, false, |
| southwest_lpe_altfuncs), |
| PIN_GROUP_WITH_OVERRIDE("spi3_grp", southwest_spi3_pins, 2, false, |
| southwest_spi3_altfuncs), |
| }; |
| |
| static const char * const southwest_uart0_groups[] = { "uart0_grp" }; |
| static const char * const southwest_uart1_groups[] = { "uart1_grp" }; |
| static const char * const southwest_uart2_groups[] = { "uart2_grp" }; |
| static const char * const southwest_hda_groups[] = { "hda_grp" }; |
| static const char * const southwest_lpe_groups[] = { "lpe_grp" }; |
| static const char * const southwest_i2c0_groups[] = { "i2c0_grp" }; |
| static const char * const southwest_i2c1_groups[] = { "i2c1_grp" }; |
| static const char * const southwest_i2c2_groups[] = { "i2c2_grp" }; |
| static const char * const southwest_i2c3_groups[] = { "i2c3_grp" }; |
| static const char * const southwest_i2c4_groups[] = { "i2c4_grp" }; |
| static const char * const southwest_i2c5_groups[] = { "i2c5_grp" }; |
| static const char * const southwest_i2c6_groups[] = { "i2c6_grp" }; |
| static const char * const southwest_i2c_nfc_groups[] = { "i2c_nfc_grp" }; |
| static const char * const southwest_spi3_groups[] = { "spi3_grp" }; |
| |
| /* |
| * Only do pinmuxing for certain LPSS devices for now. Rest of the pins are |
| * enabled only as GPIOs. |
| */ |
| static const struct chv_function southwest_functions[] = { |
| FUNCTION("uart0", southwest_uart0_groups), |
| FUNCTION("uart1", southwest_uart1_groups), |
| FUNCTION("uart2", southwest_uart2_groups), |
| FUNCTION("hda", southwest_hda_groups), |
| FUNCTION("lpe", southwest_lpe_groups), |
| FUNCTION("i2c0", southwest_i2c0_groups), |
| FUNCTION("i2c1", southwest_i2c1_groups), |
| FUNCTION("i2c2", southwest_i2c2_groups), |
| FUNCTION("i2c3", southwest_i2c3_groups), |
| FUNCTION("i2c4", southwest_i2c4_groups), |
| FUNCTION("i2c5", southwest_i2c5_groups), |
| FUNCTION("i2c6", southwest_i2c6_groups), |
| FUNCTION("i2c_nfc", southwest_i2c_nfc_groups), |
| FUNCTION("spi3", southwest_spi3_groups), |
| }; |
| |
| static const struct chv_gpio_pinrange southwest_gpio_ranges[] = { |
| GPIO_PINRANGE(0, 7), |
| GPIO_PINRANGE(15, 22), |
| GPIO_PINRANGE(30, 37), |
| GPIO_PINRANGE(45, 52), |
| GPIO_PINRANGE(60, 67), |
| GPIO_PINRANGE(75, 82), |
| GPIO_PINRANGE(90, 97), |
| }; |
| |
| static const struct chv_community southwest_community = { |
| .uid = "1", |
| .pins = southwest_pins, |
| .npins = ARRAY_SIZE(southwest_pins), |
| .groups = southwest_groups, |
| .ngroups = ARRAY_SIZE(southwest_groups), |
| .functions = southwest_functions, |
| .nfunctions = ARRAY_SIZE(southwest_functions), |
| .gpio_ranges = southwest_gpio_ranges, |
| .ngpio_ranges = ARRAY_SIZE(southwest_gpio_ranges), |
| /* |
| * Southwest community can benerate GPIO interrupts only for the |
| * first 8 interrupts. The upper half (8-15) can only be used to |
| * trigger GPEs. |
| */ |
| .nirqs = 8, |
| .acpi_space_id = 0x91, |
| }; |
| |
| static const struct pinctrl_pin_desc north_pins[] = { |
| PINCTRL_PIN(0, "GPIO_DFX_0"), |
| PINCTRL_PIN(1, "GPIO_DFX_3"), |
| PINCTRL_PIN(2, "GPIO_DFX_7"), |
| PINCTRL_PIN(3, "GPIO_DFX_1"), |
| PINCTRL_PIN(4, "GPIO_DFX_5"), |
| PINCTRL_PIN(5, "GPIO_DFX_4"), |
| PINCTRL_PIN(6, "GPIO_DFX_8"), |
| PINCTRL_PIN(7, "GPIO_DFX_2"), |
| PINCTRL_PIN(8, "GPIO_DFX_6"), |
| |
| PINCTRL_PIN(15, "GPIO_SUS0"), |
| PINCTRL_PIN(16, "SEC_GPIO_SUS10"), |
| PINCTRL_PIN(17, "GPIO_SUS3"), |
| PINCTRL_PIN(18, "GPIO_SUS7"), |
| PINCTRL_PIN(19, "GPIO_SUS1"), |
| PINCTRL_PIN(20, "GPIO_SUS5"), |
| PINCTRL_PIN(21, "SEC_GPIO_SUS11"), |
| PINCTRL_PIN(22, "GPIO_SUS4"), |
| PINCTRL_PIN(23, "SEC_GPIO_SUS8"), |
| PINCTRL_PIN(24, "GPIO_SUS2"), |
| PINCTRL_PIN(25, "GPIO_SUS6"), |
| PINCTRL_PIN(26, "CX_PREQ_B"), |
| PINCTRL_PIN(27, "SEC_GPIO_SUS9"), |
| |
| PINCTRL_PIN(30, "TRST_B"), |
| PINCTRL_PIN(31, "TCK"), |
| PINCTRL_PIN(32, "PROCHOT_B"), |
| PINCTRL_PIN(33, "SVIDO_DATA"), |
| PINCTRL_PIN(34, "TMS"), |
| PINCTRL_PIN(35, "CX_PRDY_B_2"), |
| PINCTRL_PIN(36, "TDO_2"), |
| PINCTRL_PIN(37, "CX_PRDY_B"), |
| PINCTRL_PIN(38, "SVIDO_ALERT_B"), |
| PINCTRL_PIN(39, "TDO"), |
| PINCTRL_PIN(40, "SVIDO_CLK"), |
| PINCTRL_PIN(41, "TDI"), |
| |
| PINCTRL_PIN(45, "GP_CAMERASB_05"), |
| PINCTRL_PIN(46, "GP_CAMERASB_02"), |
| PINCTRL_PIN(47, "GP_CAMERASB_08"), |
| PINCTRL_PIN(48, "GP_CAMERASB_00"), |
| PINCTRL_PIN(49, "GP_CAMERASB_06"), |
| PINCTRL_PIN(50, "GP_CAMERASB_10"), |
| PINCTRL_PIN(51, "GP_CAMERASB_03"), |
| PINCTRL_PIN(52, "GP_CAMERASB_09"), |
| PINCTRL_PIN(53, "GP_CAMERASB_01"), |
| PINCTRL_PIN(54, "GP_CAMERASB_07"), |
| PINCTRL_PIN(55, "GP_CAMERASB_11"), |
| PINCTRL_PIN(56, "GP_CAMERASB_04"), |
| |
| PINCTRL_PIN(60, "PANEL0_BKLTEN"), |
| PINCTRL_PIN(61, "HV_DDI0_HPD"), |
| PINCTRL_PIN(62, "HV_DDI2_DDC_SDA"), |
| PINCTRL_PIN(63, "PANEL1_BKLTCTL"), |
| PINCTRL_PIN(64, "HV_DDI1_HPD"), |
| PINCTRL_PIN(65, "PANEL0_BKLTCTL"), |
| PINCTRL_PIN(66, "HV_DDI0_DDC_SDA"), |
| PINCTRL_PIN(67, "HV_DDI2_DDC_SCL"), |
| PINCTRL_PIN(68, "HV_DDI2_HPD"), |
| PINCTRL_PIN(69, "PANEL1_VDDEN"), |
| PINCTRL_PIN(70, "PANEL1_BKLTEN"), |
| PINCTRL_PIN(71, "HV_DDI0_DDC_SCL"), |
| PINCTRL_PIN(72, "PANEL0_VDDEN"), |
| }; |
| |
| static const struct chv_gpio_pinrange north_gpio_ranges[] = { |
| GPIO_PINRANGE(0, 8), |
| GPIO_PINRANGE(15, 27), |
| GPIO_PINRANGE(30, 41), |
| GPIO_PINRANGE(45, 56), |
| GPIO_PINRANGE(60, 72), |
| }; |
| |
| static const struct chv_community north_community = { |
| .uid = "2", |
| .pins = north_pins, |
| .npins = ARRAY_SIZE(north_pins), |
| .gpio_ranges = north_gpio_ranges, |
| .ngpio_ranges = ARRAY_SIZE(north_gpio_ranges), |
| /* |
| * North community can generate GPIO interrupts only for the first |
| * 8 interrupts. The upper half (8-15) can only be used to trigger |
| * GPEs. |
| */ |
| .nirqs = 8, |
| .acpi_space_id = 0x92, |
| }; |
| |
| static const struct pinctrl_pin_desc east_pins[] = { |
| PINCTRL_PIN(0, "PMU_SLP_S3_B"), |
| PINCTRL_PIN(1, "PMU_BATLOW_B"), |
| PINCTRL_PIN(2, "SUS_STAT_B"), |
| PINCTRL_PIN(3, "PMU_SLP_S0IX_B"), |
| PINCTRL_PIN(4, "PMU_AC_PRESENT"), |
| PINCTRL_PIN(5, "PMU_PLTRST_B"), |
| PINCTRL_PIN(6, "PMU_SUSCLK"), |
| PINCTRL_PIN(7, "PMU_SLP_LAN_B"), |
| PINCTRL_PIN(8, "PMU_PWRBTN_B"), |
| PINCTRL_PIN(9, "PMU_SLP_S4_B"), |
| PINCTRL_PIN(10, "PMU_WAKE_B"), |
| PINCTRL_PIN(11, "PMU_WAKE_LAN_B"), |
| |
| PINCTRL_PIN(15, "MF_ISH_GPIO_3"), |
| PINCTRL_PIN(16, "MF_ISH_GPIO_7"), |
| PINCTRL_PIN(17, "MF_ISH_I2C1_SCL"), |
| PINCTRL_PIN(18, "MF_ISH_GPIO_1"), |
| PINCTRL_PIN(19, "MF_ISH_GPIO_5"), |
| PINCTRL_PIN(20, "MF_ISH_GPIO_9"), |
| PINCTRL_PIN(21, "MF_ISH_GPIO_0"), |
| PINCTRL_PIN(22, "MF_ISH_GPIO_4"), |
| PINCTRL_PIN(23, "MF_ISH_GPIO_8"), |
| PINCTRL_PIN(24, "MF_ISH_GPIO_2"), |
| PINCTRL_PIN(25, "MF_ISH_GPIO_6"), |
| PINCTRL_PIN(26, "MF_ISH_I2C1_SDA"), |
| }; |
| |
| static const struct chv_gpio_pinrange east_gpio_ranges[] = { |
| GPIO_PINRANGE(0, 11), |
| GPIO_PINRANGE(15, 26), |
| }; |
| |
| static const struct chv_community east_community = { |
| .uid = "3", |
| .pins = east_pins, |
| .npins = ARRAY_SIZE(east_pins), |
| .gpio_ranges = east_gpio_ranges, |
| .ngpio_ranges = ARRAY_SIZE(east_gpio_ranges), |
| .nirqs = 16, |
| .acpi_space_id = 0x93, |
| }; |
| |
| static const struct pinctrl_pin_desc southeast_pins[] = { |
| PINCTRL_PIN(0, "MF_PLT_CLK0"), |
| PINCTRL_PIN(1, "PWM1"), |
| PINCTRL_PIN(2, "MF_PLT_CLK1"), |
| PINCTRL_PIN(3, "MF_PLT_CLK4"), |
| PINCTRL_PIN(4, "MF_PLT_CLK3"), |
| PINCTRL_PIN(5, "PWM0"), |
| PINCTRL_PIN(6, "MF_PLT_CLK5"), |
| PINCTRL_PIN(7, "MF_PLT_CLK2"), |
| |
| PINCTRL_PIN(15, "SDMMC2_D3_CD_B"), |
| PINCTRL_PIN(16, "SDMMC1_CLK"), |
| PINCTRL_PIN(17, "SDMMC1_D0"), |
| PINCTRL_PIN(18, "SDMMC2_D1"), |
| PINCTRL_PIN(19, "SDMMC2_CLK"), |
| PINCTRL_PIN(20, "SDMMC1_D2"), |
| PINCTRL_PIN(21, "SDMMC2_D2"), |
| PINCTRL_PIN(22, "SDMMC2_CMD"), |
| PINCTRL_PIN(23, "SDMMC1_CMD"), |
| PINCTRL_PIN(24, "SDMMC1_D1"), |
| PINCTRL_PIN(25, "SDMMC2_D0"), |
| PINCTRL_PIN(26, "SDMMC1_D3_CD_B"), |
| |
| PINCTRL_PIN(30, "SDMMC3_D1"), |
| PINCTRL_PIN(31, "SDMMC3_CLK"), |
| PINCTRL_PIN(32, "SDMMC3_D3"), |
| PINCTRL_PIN(33, "SDMMC3_D2"), |
| PINCTRL_PIN(34, "SDMMC3_CMD"), |
| PINCTRL_PIN(35, "SDMMC3_D0"), |
| |
| PINCTRL_PIN(45, "MF_LPC_AD2"), |
| PINCTRL_PIN(46, "LPC_CLKRUNB"), |
| PINCTRL_PIN(47, "MF_LPC_AD0"), |
| PINCTRL_PIN(48, "LPC_FRAMEB"), |
| PINCTRL_PIN(49, "MF_LPC_CLKOUT1"), |
| PINCTRL_PIN(50, "MF_LPC_AD3"), |
| PINCTRL_PIN(51, "MF_LPC_CLKOUT0"), |
| PINCTRL_PIN(52, "MF_LPC_AD1"), |
| |
| PINCTRL_PIN(60, "SPI1_MISO"), |
| PINCTRL_PIN(61, "SPI1_CSO_B"), |
| PINCTRL_PIN(62, "SPI1_CLK"), |
| PINCTRL_PIN(63, "MMC1_D6"), |
| PINCTRL_PIN(64, "SPI1_MOSI"), |
| PINCTRL_PIN(65, "MMC1_D5"), |
| PINCTRL_PIN(66, "SPI1_CS1_B"), |
| PINCTRL_PIN(67, "MMC1_D4_SD_WE"), |
| PINCTRL_PIN(68, "MMC1_D7"), |
| PINCTRL_PIN(69, "MMC1_RCLK"), |
| |
| PINCTRL_PIN(75, "USB_OC1_B"), |
| PINCTRL_PIN(76, "PMU_RESETBUTTON_B"), |
| PINCTRL_PIN(77, "GPIO_ALERT"), |
| PINCTRL_PIN(78, "SDMMC3_PWR_EN_B"), |
| PINCTRL_PIN(79, "ILB_SERIRQ"), |
| PINCTRL_PIN(80, "USB_OC0_B"), |
| PINCTRL_PIN(81, "SDMMC3_CD_B"), |
| PINCTRL_PIN(82, "SPKR"), |
| PINCTRL_PIN(83, "SUSPWRDNACK"), |
| PINCTRL_PIN(84, "SPARE_PIN"), |
| PINCTRL_PIN(85, "SDMMC3_1P8_EN"), |
| }; |
| |
| static const unsigned southeast_pwm0_pins[] = { 5 }; |
| static const unsigned southeast_pwm1_pins[] = { 1 }; |
| static const unsigned southeast_sdmmc1_pins[] = { |
| 16, 17, 20, 23, 24, 26, 63, 65, 67, 68, 69, |
| }; |
| static const unsigned southeast_sdmmc2_pins[] = { 15, 18, 19, 21, 22, 25 }; |
| static const unsigned southeast_sdmmc3_pins[] = { |
| 30, 31, 32, 33, 34, 35, 78, 81, 85, |
| }; |
| static const unsigned southeast_spi1_pins[] = { 60, 61, 62, 64, 66 }; |
| static const unsigned southeast_spi2_pins[] = { 2, 3, 4, 6, 7 }; |
| |
| static const struct chv_pingroup southeast_groups[] = { |
| PIN_GROUP("pwm0_grp", southeast_pwm0_pins, 1, false), |
| PIN_GROUP("pwm1_grp", southeast_pwm1_pins, 1, false), |
| PIN_GROUP("sdmmc1_grp", southeast_sdmmc1_pins, 1, false), |
| PIN_GROUP("sdmmc2_grp", southeast_sdmmc2_pins, 1, false), |
| PIN_GROUP("sdmmc3_grp", southeast_sdmmc3_pins, 1, false), |
| PIN_GROUP("spi1_grp", southeast_spi1_pins, 1, false), |
| PIN_GROUP("spi2_grp", southeast_spi2_pins, 4, false), |
| }; |
| |
| static const char * const southeast_pwm0_groups[] = { "pwm0_grp" }; |
| static const char * const southeast_pwm1_groups[] = { "pwm1_grp" }; |
| static const char * const southeast_sdmmc1_groups[] = { "sdmmc1_grp" }; |
| static const char * const southeast_sdmmc2_groups[] = { "sdmmc2_grp" }; |
| static const char * const southeast_sdmmc3_groups[] = { "sdmmc3_grp" }; |
| static const char * const southeast_spi1_groups[] = { "spi1_grp" }; |
| static const char * const southeast_spi2_groups[] = { "spi2_grp" }; |
| |
| static const struct chv_function southeast_functions[] = { |
| FUNCTION("pwm0", southeast_pwm0_groups), |
| FUNCTION("pwm1", southeast_pwm1_groups), |
| FUNCTION("sdmmc1", southeast_sdmmc1_groups), |
| FUNCTION("sdmmc2", southeast_sdmmc2_groups), |
| FUNCTION("sdmmc3", southeast_sdmmc3_groups), |
| FUNCTION("spi1", southeast_spi1_groups), |
| FUNCTION("spi2", southeast_spi2_groups), |
| }; |
| |
| static const struct chv_gpio_pinrange southeast_gpio_ranges[] = { |
| GPIO_PINRANGE(0, 7), |
| GPIO_PINRANGE(15, 26), |
| GPIO_PINRANGE(30, 35), |
| GPIO_PINRANGE(45, 52), |
| GPIO_PINRANGE(60, 69), |
| GPIO_PINRANGE(75, 85), |
| }; |
| |
| static const struct chv_community southeast_community = { |
| .uid = "4", |
| .pins = southeast_pins, |
| .npins = ARRAY_SIZE(southeast_pins), |
| .groups = southeast_groups, |
| .ngroups = ARRAY_SIZE(southeast_groups), |
| .functions = southeast_functions, |
| .nfunctions = ARRAY_SIZE(southeast_functions), |
| .gpio_ranges = southeast_gpio_ranges, |
| .ngpio_ranges = ARRAY_SIZE(southeast_gpio_ranges), |
| .nirqs = 16, |
| .acpi_space_id = 0x94, |
| }; |
| |
| static const struct chv_community *chv_communities[] = { |
| &southwest_community, |
| &north_community, |
| &east_community, |
| &southeast_community, |
| }; |
| |
| /* |
| * Lock to serialize register accesses |
| * |
| * Due to a silicon issue, a shared lock must be used to prevent |
| * concurrent accesses across the 4 GPIO controllers. |
| * |
| * See Intel Atom Z8000 Processor Series Specification Update (Rev. 005), |
| * errata #CHT34, for further information. |
| */ |
| static DEFINE_RAW_SPINLOCK(chv_lock); |
| |
| static void __iomem *chv_padreg(struct chv_pinctrl *pctrl, unsigned offset, |
| unsigned reg) |
| { |
| unsigned family_no = offset / MAX_FAMILY_PAD_GPIO_NO; |
| unsigned pad_no = offset % MAX_FAMILY_PAD_GPIO_NO; |
| |
| offset = FAMILY_PAD_REGS_OFF + FAMILY_PAD_REGS_SIZE * family_no + |
| GPIO_REGS_SIZE * pad_no; |
| |
| return pctrl->regs + offset + reg; |
| } |
| |
| static void chv_writel(u32 value, void __iomem *reg) |
| { |
| writel(value, reg); |
| /* simple readback to confirm the bus transferring done */ |
| readl(reg); |
| } |
| |
| /* When Pad Cfg is locked, driver can only change GPIOTXState or GPIORXState */ |
| static bool chv_pad_locked(struct chv_pinctrl *pctrl, unsigned offset) |
| { |
| void __iomem *reg; |
| |
| reg = chv_padreg(pctrl, offset, CHV_PADCTRL1); |
| return readl(reg) & CHV_PADCTRL1_CFGLOCK; |
| } |
| |
| static int chv_get_groups_count(struct pinctrl_dev *pctldev) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| |
| return pctrl->community->ngroups; |
| } |
| |
| static const char *chv_get_group_name(struct pinctrl_dev *pctldev, |
| unsigned group) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| |
| return pctrl->community->groups[group].name; |
| } |
| |
| static int chv_get_group_pins(struct pinctrl_dev *pctldev, unsigned group, |
| const unsigned **pins, unsigned *npins) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| |
| *pins = pctrl->community->groups[group].pins; |
| *npins = pctrl->community->groups[group].npins; |
| return 0; |
| } |
| |
| static void chv_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, |
| unsigned offset) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| unsigned long flags; |
| u32 ctrl0, ctrl1; |
| bool locked; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| ctrl0 = readl(chv_padreg(pctrl, offset, CHV_PADCTRL0)); |
| ctrl1 = readl(chv_padreg(pctrl, offset, CHV_PADCTRL1)); |
| locked = chv_pad_locked(pctrl, offset); |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| if (ctrl0 & CHV_PADCTRL0_GPIOEN) { |
| seq_puts(s, "GPIO "); |
| } else { |
| u32 mode; |
| |
| mode = ctrl0 & CHV_PADCTRL0_PMODE_MASK; |
| mode >>= CHV_PADCTRL0_PMODE_SHIFT; |
| |
| seq_printf(s, "mode %d ", mode); |
| } |
| |
| seq_printf(s, "0x%08x 0x%08x", ctrl0, ctrl1); |
| |
| if (locked) |
| seq_puts(s, " [LOCKED]"); |
| } |
| |
| static const struct pinctrl_ops chv_pinctrl_ops = { |
| .get_groups_count = chv_get_groups_count, |
| .get_group_name = chv_get_group_name, |
| .get_group_pins = chv_get_group_pins, |
| .pin_dbg_show = chv_pin_dbg_show, |
| }; |
| |
| static int chv_get_functions_count(struct pinctrl_dev *pctldev) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| |
| return pctrl->community->nfunctions; |
| } |
| |
| static const char *chv_get_function_name(struct pinctrl_dev *pctldev, |
| unsigned function) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| |
| return pctrl->community->functions[function].name; |
| } |
| |
| static int chv_get_function_groups(struct pinctrl_dev *pctldev, |
| unsigned function, |
| const char * const **groups, |
| unsigned * const ngroups) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| |
| *groups = pctrl->community->functions[function].groups; |
| *ngroups = pctrl->community->functions[function].ngroups; |
| return 0; |
| } |
| |
| static int chv_pinmux_set_mux(struct pinctrl_dev *pctldev, unsigned function, |
| unsigned group) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| const struct chv_pingroup *grp; |
| unsigned long flags; |
| int i; |
| |
| grp = &pctrl->community->groups[group]; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| /* Check first that the pad is not locked */ |
| for (i = 0; i < grp->npins; i++) { |
| if (chv_pad_locked(pctrl, grp->pins[i])) { |
| dev_warn(pctrl->dev, "unable to set mode for locked pin %u\n", |
| grp->pins[i]); |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| return -EBUSY; |
| } |
| } |
| |
| for (i = 0; i < grp->npins; i++) { |
| const struct chv_alternate_function *altfunc = &grp->altfunc; |
| int pin = grp->pins[i]; |
| void __iomem *reg; |
| u32 value; |
| |
| /* Check if there is pin-specific config */ |
| if (grp->overrides) { |
| int j; |
| |
| for (j = 0; j < grp->noverrides; j++) { |
| if (grp->overrides[j].pin == pin) { |
| altfunc = &grp->overrides[j]; |
| break; |
| } |
| } |
| } |
| |
| reg = chv_padreg(pctrl, pin, CHV_PADCTRL0); |
| value = readl(reg); |
| /* Disable GPIO mode */ |
| value &= ~CHV_PADCTRL0_GPIOEN; |
| /* Set to desired mode */ |
| value &= ~CHV_PADCTRL0_PMODE_MASK; |
| value |= altfunc->mode << CHV_PADCTRL0_PMODE_SHIFT; |
| chv_writel(value, reg); |
| |
| /* Update for invert_oe */ |
| reg = chv_padreg(pctrl, pin, CHV_PADCTRL1); |
| value = readl(reg) & ~CHV_PADCTRL1_INVRXTX_MASK; |
| if (altfunc->invert_oe) |
| value |= CHV_PADCTRL1_INVRXTX_TXENABLE; |
| chv_writel(value, reg); |
| |
| dev_dbg(pctrl->dev, "configured pin %u mode %u OE %sinverted\n", |
| pin, altfunc->mode, altfunc->invert_oe ? "" : "not "); |
| } |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return 0; |
| } |
| |
| static int chv_gpio_request_enable(struct pinctrl_dev *pctldev, |
| struct pinctrl_gpio_range *range, |
| unsigned offset) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| unsigned long flags; |
| void __iomem *reg; |
| u32 value; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| if (chv_pad_locked(pctrl, offset)) { |
| value = readl(chv_padreg(pctrl, offset, CHV_PADCTRL0)); |
| if (!(value & CHV_PADCTRL0_GPIOEN)) { |
| /* Locked so cannot enable */ |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| return -EBUSY; |
| } |
| } else { |
| int i; |
| |
| /* Reset the interrupt mapping */ |
| for (i = 0; i < ARRAY_SIZE(pctrl->intr_lines); i++) { |
| if (pctrl->intr_lines[i] == offset) { |
| pctrl->intr_lines[i] = 0; |
| break; |
| } |
| } |
| |
| /* Disable interrupt generation */ |
| reg = chv_padreg(pctrl, offset, CHV_PADCTRL1); |
| value = readl(reg); |
| value &= ~CHV_PADCTRL1_INTWAKECFG_MASK; |
| value &= ~CHV_PADCTRL1_INVRXTX_MASK; |
| chv_writel(value, reg); |
| |
| reg = chv_padreg(pctrl, offset, CHV_PADCTRL0); |
| value = readl(reg); |
| |
| /* |
| * If the pin is in HiZ mode (both TX and RX buffers are |
| * disabled) we turn it to be input now. |
| */ |
| if ((value & CHV_PADCTRL0_GPIOCFG_MASK) == |
| (CHV_PADCTRL0_GPIOCFG_HIZ << CHV_PADCTRL0_GPIOCFG_SHIFT)) { |
| value &= ~CHV_PADCTRL0_GPIOCFG_MASK; |
| value |= CHV_PADCTRL0_GPIOCFG_GPI << |
| CHV_PADCTRL0_GPIOCFG_SHIFT; |
| } |
| |
| /* Switch to a GPIO mode */ |
| value |= CHV_PADCTRL0_GPIOEN; |
| chv_writel(value, reg); |
| } |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return 0; |
| } |
| |
| static void chv_gpio_disable_free(struct pinctrl_dev *pctldev, |
| struct pinctrl_gpio_range *range, |
| unsigned offset) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| unsigned long flags; |
| void __iomem *reg; |
| u32 value; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| reg = chv_padreg(pctrl, offset, CHV_PADCTRL0); |
| value = readl(reg) & ~CHV_PADCTRL0_GPIOEN; |
| chv_writel(value, reg); |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| } |
| |
| static int chv_gpio_set_direction(struct pinctrl_dev *pctldev, |
| struct pinctrl_gpio_range *range, |
| unsigned offset, bool input) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| void __iomem *reg = chv_padreg(pctrl, offset, CHV_PADCTRL0); |
| unsigned long flags; |
| u32 ctrl0; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| ctrl0 = readl(reg) & ~CHV_PADCTRL0_GPIOCFG_MASK; |
| if (input) |
| ctrl0 |= CHV_PADCTRL0_GPIOCFG_GPI << CHV_PADCTRL0_GPIOCFG_SHIFT; |
| else |
| ctrl0 |= CHV_PADCTRL0_GPIOCFG_GPO << CHV_PADCTRL0_GPIOCFG_SHIFT; |
| chv_writel(ctrl0, reg); |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return 0; |
| } |
| |
| static const struct pinmux_ops chv_pinmux_ops = { |
| .get_functions_count = chv_get_functions_count, |
| .get_function_name = chv_get_function_name, |
| .get_function_groups = chv_get_function_groups, |
| .set_mux = chv_pinmux_set_mux, |
| .gpio_request_enable = chv_gpio_request_enable, |
| .gpio_disable_free = chv_gpio_disable_free, |
| .gpio_set_direction = chv_gpio_set_direction, |
| }; |
| |
| static int chv_config_get(struct pinctrl_dev *pctldev, unsigned pin, |
| unsigned long *config) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| enum pin_config_param param = pinconf_to_config_param(*config); |
| unsigned long flags; |
| u32 ctrl0, ctrl1; |
| u16 arg = 0; |
| u32 term; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| ctrl0 = readl(chv_padreg(pctrl, pin, CHV_PADCTRL0)); |
| ctrl1 = readl(chv_padreg(pctrl, pin, CHV_PADCTRL1)); |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| term = (ctrl0 & CHV_PADCTRL0_TERM_MASK) >> CHV_PADCTRL0_TERM_SHIFT; |
| |
| switch (param) { |
| case PIN_CONFIG_BIAS_DISABLE: |
| if (term) |
| return -EINVAL; |
| break; |
| |
| case PIN_CONFIG_BIAS_PULL_UP: |
| if (!(ctrl0 & CHV_PADCTRL0_TERM_UP)) |
| return -EINVAL; |
| |
| switch (term) { |
| case CHV_PADCTRL0_TERM_20K: |
| arg = 20000; |
| break; |
| case CHV_PADCTRL0_TERM_5K: |
| arg = 5000; |
| break; |
| case CHV_PADCTRL0_TERM_1K: |
| arg = 1000; |
| break; |
| } |
| |
| break; |
| |
| case PIN_CONFIG_BIAS_PULL_DOWN: |
| if (!term || (ctrl0 & CHV_PADCTRL0_TERM_UP)) |
| return -EINVAL; |
| |
| switch (term) { |
| case CHV_PADCTRL0_TERM_20K: |
| arg = 20000; |
| break; |
| case CHV_PADCTRL0_TERM_5K: |
| arg = 5000; |
| break; |
| } |
| |
| break; |
| |
| case PIN_CONFIG_DRIVE_OPEN_DRAIN: |
| if (!(ctrl1 & CHV_PADCTRL1_ODEN)) |
| return -EINVAL; |
| break; |
| |
| case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: { |
| u32 cfg; |
| |
| cfg = ctrl0 & CHV_PADCTRL0_GPIOCFG_MASK; |
| cfg >>= CHV_PADCTRL0_GPIOCFG_SHIFT; |
| if (cfg != CHV_PADCTRL0_GPIOCFG_HIZ) |
| return -EINVAL; |
| |
| break; |
| } |
| |
| default: |
| return -ENOTSUPP; |
| } |
| |
| *config = pinconf_to_config_packed(param, arg); |
| return 0; |
| } |
| |
| static int chv_config_set_pull(struct chv_pinctrl *pctrl, unsigned pin, |
| enum pin_config_param param, u32 arg) |
| { |
| void __iomem *reg = chv_padreg(pctrl, pin, CHV_PADCTRL0); |
| unsigned long flags; |
| u32 ctrl0, pull; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| ctrl0 = readl(reg); |
| |
| switch (param) { |
| case PIN_CONFIG_BIAS_DISABLE: |
| ctrl0 &= ~(CHV_PADCTRL0_TERM_MASK | CHV_PADCTRL0_TERM_UP); |
| break; |
| |
| case PIN_CONFIG_BIAS_PULL_UP: |
| ctrl0 &= ~(CHV_PADCTRL0_TERM_MASK | CHV_PADCTRL0_TERM_UP); |
| |
| switch (arg) { |
| case 1000: |
| /* For 1k there is only pull up */ |
| pull = CHV_PADCTRL0_TERM_1K << CHV_PADCTRL0_TERM_SHIFT; |
| break; |
| case 5000: |
| pull = CHV_PADCTRL0_TERM_5K << CHV_PADCTRL0_TERM_SHIFT; |
| break; |
| case 20000: |
| pull = CHV_PADCTRL0_TERM_20K << CHV_PADCTRL0_TERM_SHIFT; |
| break; |
| default: |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| return -EINVAL; |
| } |
| |
| ctrl0 |= CHV_PADCTRL0_TERM_UP | pull; |
| break; |
| |
| case PIN_CONFIG_BIAS_PULL_DOWN: |
| ctrl0 &= ~(CHV_PADCTRL0_TERM_MASK | CHV_PADCTRL0_TERM_UP); |
| |
| switch (arg) { |
| case 5000: |
| pull = CHV_PADCTRL0_TERM_5K << CHV_PADCTRL0_TERM_SHIFT; |
| break; |
| case 20000: |
| pull = CHV_PADCTRL0_TERM_20K << CHV_PADCTRL0_TERM_SHIFT; |
| break; |
| default: |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| return -EINVAL; |
| } |
| |
| ctrl0 |= pull; |
| break; |
| |
| default: |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| return -EINVAL; |
| } |
| |
| chv_writel(ctrl0, reg); |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return 0; |
| } |
| |
| static int chv_config_set_oden(struct chv_pinctrl *pctrl, unsigned int pin, |
| bool enable) |
| { |
| void __iomem *reg = chv_padreg(pctrl, pin, CHV_PADCTRL1); |
| unsigned long flags; |
| u32 ctrl1; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| ctrl1 = readl(reg); |
| |
| if (enable) |
| ctrl1 |= CHV_PADCTRL1_ODEN; |
| else |
| ctrl1 &= ~CHV_PADCTRL1_ODEN; |
| |
| chv_writel(ctrl1, reg); |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return 0; |
| } |
| |
| static int chv_config_set(struct pinctrl_dev *pctldev, unsigned pin, |
| unsigned long *configs, unsigned nconfigs) |
| { |
| struct chv_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev); |
| enum pin_config_param param; |
| int i, ret; |
| u32 arg; |
| |
| if (chv_pad_locked(pctrl, pin)) |
| return -EBUSY; |
| |
| for (i = 0; i < nconfigs; i++) { |
| param = pinconf_to_config_param(configs[i]); |
| arg = pinconf_to_config_argument(configs[i]); |
| |
| switch (param) { |
| case PIN_CONFIG_BIAS_DISABLE: |
| case PIN_CONFIG_BIAS_PULL_UP: |
| case PIN_CONFIG_BIAS_PULL_DOWN: |
| ret = chv_config_set_pull(pctrl, pin, param, arg); |
| if (ret) |
| return ret; |
| break; |
| |
| case PIN_CONFIG_DRIVE_PUSH_PULL: |
| ret = chv_config_set_oden(pctrl, pin, false); |
| if (ret) |
| return ret; |
| break; |
| |
| case PIN_CONFIG_DRIVE_OPEN_DRAIN: |
| ret = chv_config_set_oden(pctrl, pin, true); |
| if (ret) |
| return ret; |
| break; |
| |
| default: |
| return -ENOTSUPP; |
| } |
| |
| dev_dbg(pctrl->dev, "pin %d set config %d arg %u\n", pin, |
| param, arg); |
| } |
| |
| return 0; |
| } |
| |
| static int chv_config_group_get(struct pinctrl_dev *pctldev, |
| unsigned int group, |
| unsigned long *config) |
| { |
| const unsigned int *pins; |
| unsigned int npins; |
| int ret; |
| |
| ret = chv_get_group_pins(pctldev, group, &pins, &npins); |
| if (ret) |
| return ret; |
| |
| ret = chv_config_get(pctldev, pins[0], config); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int chv_config_group_set(struct pinctrl_dev *pctldev, |
| unsigned int group, unsigned long *configs, |
| unsigned int num_configs) |
| { |
| const unsigned int *pins; |
| unsigned int npins; |
| int i, ret; |
| |
| ret = chv_get_group_pins(pctldev, group, &pins, &npins); |
| if (ret) |
| return ret; |
| |
| for (i = 0; i < npins; i++) { |
| ret = chv_config_set(pctldev, pins[i], configs, num_configs); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static const struct pinconf_ops chv_pinconf_ops = { |
| .is_generic = true, |
| .pin_config_set = chv_config_set, |
| .pin_config_get = chv_config_get, |
| .pin_config_group_get = chv_config_group_get, |
| .pin_config_group_set = chv_config_group_set, |
| }; |
| |
| static struct pinctrl_desc chv_pinctrl_desc = { |
| .pctlops = &chv_pinctrl_ops, |
| .pmxops = &chv_pinmux_ops, |
| .confops = &chv_pinconf_ops, |
| .owner = THIS_MODULE, |
| }; |
| |
| static int chv_gpio_get(struct gpio_chip *chip, unsigned offset) |
| { |
| struct chv_pinctrl *pctrl = gpiochip_get_data(chip); |
| unsigned long flags; |
| u32 ctrl0, cfg; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| ctrl0 = readl(chv_padreg(pctrl, offset, CHV_PADCTRL0)); |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| cfg = ctrl0 & CHV_PADCTRL0_GPIOCFG_MASK; |
| cfg >>= CHV_PADCTRL0_GPIOCFG_SHIFT; |
| |
| if (cfg == CHV_PADCTRL0_GPIOCFG_GPO) |
| return !!(ctrl0 & CHV_PADCTRL0_GPIOTXSTATE); |
| return !!(ctrl0 & CHV_PADCTRL0_GPIORXSTATE); |
| } |
| |
| static void chv_gpio_set(struct gpio_chip *chip, unsigned offset, int value) |
| { |
| struct chv_pinctrl *pctrl = gpiochip_get_data(chip); |
| unsigned long flags; |
| void __iomem *reg; |
| u32 ctrl0; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| reg = chv_padreg(pctrl, offset, CHV_PADCTRL0); |
| ctrl0 = readl(reg); |
| |
| if (value) |
| ctrl0 |= CHV_PADCTRL0_GPIOTXSTATE; |
| else |
| ctrl0 &= ~CHV_PADCTRL0_GPIOTXSTATE; |
| |
| chv_writel(ctrl0, reg); |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| } |
| |
| static int chv_gpio_get_direction(struct gpio_chip *chip, unsigned offset) |
| { |
| struct chv_pinctrl *pctrl = gpiochip_get_data(chip); |
| u32 ctrl0, direction; |
| unsigned long flags; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| ctrl0 = readl(chv_padreg(pctrl, offset, CHV_PADCTRL0)); |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| direction = ctrl0 & CHV_PADCTRL0_GPIOCFG_MASK; |
| direction >>= CHV_PADCTRL0_GPIOCFG_SHIFT; |
| |
| return direction != CHV_PADCTRL0_GPIOCFG_GPO; |
| } |
| |
| static int chv_gpio_direction_input(struct gpio_chip *chip, unsigned offset) |
| { |
| return pinctrl_gpio_direction_input(chip->base + offset); |
| } |
| |
| static int chv_gpio_direction_output(struct gpio_chip *chip, unsigned offset, |
| int value) |
| { |
| chv_gpio_set(chip, offset, value); |
| return pinctrl_gpio_direction_output(chip->base + offset); |
| } |
| |
| static const struct gpio_chip chv_gpio_chip = { |
| .owner = THIS_MODULE, |
| .request = gpiochip_generic_request, |
| .free = gpiochip_generic_free, |
| .get_direction = chv_gpio_get_direction, |
| .direction_input = chv_gpio_direction_input, |
| .direction_output = chv_gpio_direction_output, |
| .get = chv_gpio_get, |
| .set = chv_gpio_set, |
| }; |
| |
| static void chv_gpio_irq_ack(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct chv_pinctrl *pctrl = gpiochip_get_data(gc); |
| int pin = irqd_to_hwirq(d); |
| u32 intr_line; |
| |
| raw_spin_lock(&chv_lock); |
| |
| intr_line = readl(chv_padreg(pctrl, pin, CHV_PADCTRL0)); |
| intr_line &= CHV_PADCTRL0_INTSEL_MASK; |
| intr_line >>= CHV_PADCTRL0_INTSEL_SHIFT; |
| chv_writel(BIT(intr_line), pctrl->regs + CHV_INTSTAT); |
| |
| raw_spin_unlock(&chv_lock); |
| } |
| |
| static void chv_gpio_irq_mask_unmask(struct irq_data *d, bool mask) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct chv_pinctrl *pctrl = gpiochip_get_data(gc); |
| int pin = irqd_to_hwirq(d); |
| u32 value, intr_line; |
| unsigned long flags; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| intr_line = readl(chv_padreg(pctrl, pin, CHV_PADCTRL0)); |
| intr_line &= CHV_PADCTRL0_INTSEL_MASK; |
| intr_line >>= CHV_PADCTRL0_INTSEL_SHIFT; |
| |
| value = readl(pctrl->regs + CHV_INTMASK); |
| if (mask) |
| value &= ~BIT(intr_line); |
| else |
| value |= BIT(intr_line); |
| chv_writel(value, pctrl->regs + CHV_INTMASK); |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| } |
| |
| static void chv_gpio_irq_mask(struct irq_data *d) |
| { |
| chv_gpio_irq_mask_unmask(d, true); |
| } |
| |
| static void chv_gpio_irq_unmask(struct irq_data *d) |
| { |
| chv_gpio_irq_mask_unmask(d, false); |
| } |
| |
| static unsigned chv_gpio_irq_startup(struct irq_data *d) |
| { |
| /* |
| * Check if the interrupt has been requested with 0 as triggering |
| * type. In that case it is assumed that the current values |
| * programmed to the hardware are used (e.g BIOS configured |
| * defaults). |
| * |
| * In that case ->irq_set_type() will never be called so we need to |
| * read back the values from hardware now, set correct flow handler |
| * and update mappings before the interrupt is being used. |
| */ |
| if (irqd_get_trigger_type(d) == IRQ_TYPE_NONE) { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct chv_pinctrl *pctrl = gpiochip_get_data(gc); |
| unsigned pin = irqd_to_hwirq(d); |
| irq_flow_handler_t handler; |
| unsigned long flags; |
| u32 intsel, value; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| intsel = readl(chv_padreg(pctrl, pin, CHV_PADCTRL0)); |
| intsel &= CHV_PADCTRL0_INTSEL_MASK; |
| intsel >>= CHV_PADCTRL0_INTSEL_SHIFT; |
| |
| value = readl(chv_padreg(pctrl, pin, CHV_PADCTRL1)); |
| if (value & CHV_PADCTRL1_INTWAKECFG_LEVEL) |
| handler = handle_level_irq; |
| else |
| handler = handle_edge_irq; |
| |
| if (!pctrl->intr_lines[intsel]) { |
| irq_set_handler_locked(d, handler); |
| pctrl->intr_lines[intsel] = pin; |
| } |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| } |
| |
| chv_gpio_irq_unmask(d); |
| return 0; |
| } |
| |
| static int chv_gpio_irq_type(struct irq_data *d, unsigned type) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct chv_pinctrl *pctrl = gpiochip_get_data(gc); |
| unsigned pin = irqd_to_hwirq(d); |
| unsigned long flags; |
| u32 value; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| /* |
| * Pins which can be used as shared interrupt are configured in |
| * BIOS. Driver trusts BIOS configurations and assigns different |
| * handler according to the irq type. |
| * |
| * Driver needs to save the mapping between each pin and |
| * its interrupt line. |
| * 1. If the pin cfg is locked in BIOS: |
| * Trust BIOS has programmed IntWakeCfg bits correctly, |
| * driver just needs to save the mapping. |
| * 2. If the pin cfg is not locked in BIOS: |
| * Driver programs the IntWakeCfg bits and save the mapping. |
| */ |
| if (!chv_pad_locked(pctrl, pin)) { |
| void __iomem *reg = chv_padreg(pctrl, pin, CHV_PADCTRL1); |
| |
| value = readl(reg); |
| value &= ~CHV_PADCTRL1_INTWAKECFG_MASK; |
| value &= ~CHV_PADCTRL1_INVRXTX_MASK; |
| |
| if (type & IRQ_TYPE_EDGE_BOTH) { |
| if ((type & IRQ_TYPE_EDGE_BOTH) == IRQ_TYPE_EDGE_BOTH) |
| value |= CHV_PADCTRL1_INTWAKECFG_BOTH; |
| else if (type & IRQ_TYPE_EDGE_RISING) |
| value |= CHV_PADCTRL1_INTWAKECFG_RISING; |
| else if (type & IRQ_TYPE_EDGE_FALLING) |
| value |= CHV_PADCTRL1_INTWAKECFG_FALLING; |
| } else if (type & IRQ_TYPE_LEVEL_MASK) { |
| value |= CHV_PADCTRL1_INTWAKECFG_LEVEL; |
| if (type & IRQ_TYPE_LEVEL_LOW) |
| value |= CHV_PADCTRL1_INVRXTX_RXDATA; |
| } |
| |
| chv_writel(value, reg); |
| } |
| |
| value = readl(chv_padreg(pctrl, pin, CHV_PADCTRL0)); |
| value &= CHV_PADCTRL0_INTSEL_MASK; |
| value >>= CHV_PADCTRL0_INTSEL_SHIFT; |
| |
| pctrl->intr_lines[value] = pin; |
| |
| if (type & IRQ_TYPE_EDGE_BOTH) |
| irq_set_handler_locked(d, handle_edge_irq); |
| else if (type & IRQ_TYPE_LEVEL_MASK) |
| irq_set_handler_locked(d, handle_level_irq); |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return 0; |
| } |
| |
| static struct irq_chip chv_gpio_irqchip = { |
| .name = "chv-gpio", |
| .irq_startup = chv_gpio_irq_startup, |
| .irq_ack = chv_gpio_irq_ack, |
| .irq_mask = chv_gpio_irq_mask, |
| .irq_unmask = chv_gpio_irq_unmask, |
| .irq_set_type = chv_gpio_irq_type, |
| .flags = IRQCHIP_SKIP_SET_WAKE, |
| }; |
| |
| static void chv_gpio_irq_handler(struct irq_desc *desc) |
| { |
| struct gpio_chip *gc = irq_desc_get_handler_data(desc); |
| struct chv_pinctrl *pctrl = gpiochip_get_data(gc); |
| struct irq_chip *chip = irq_desc_get_chip(desc); |
| unsigned long pending; |
| u32 intr_line; |
| |
| chained_irq_enter(chip, desc); |
| |
| pending = readl(pctrl->regs + CHV_INTSTAT); |
| for_each_set_bit(intr_line, &pending, pctrl->community->nirqs) { |
| unsigned irq, offset; |
| |
| offset = pctrl->intr_lines[intr_line]; |
| irq = irq_find_mapping(gc->irq.domain, offset); |
| generic_handle_irq(irq); |
| } |
| |
| chained_irq_exit(chip, desc); |
| } |
| |
| /* |
| * Certain machines seem to hardcode Linux IRQ numbers in their ACPI |
| * tables. Since we leave GPIOs that are not capable of generating |
| * interrupts out of the irqdomain the numbering will be different and |
| * cause devices using the hardcoded IRQ numbers fail. In order not to |
| * break such machines we will only mask pins from irqdomain if the machine |
| * is not listed below. |
| */ |
| static const struct dmi_system_id chv_no_valid_mask[] = { |
| /* See https://bugzilla.kernel.org/show_bug.cgi?id=194945 */ |
| { |
| .ident = "Intel_Strago based Chromebooks (All models)", |
| .matches = { |
| DMI_MATCH(DMI_SYS_VENDOR, "GOOGLE"), |
| DMI_MATCH(DMI_PRODUCT_FAMILY, "Intel_Strago"), |
| }, |
| }, |
| { |
| .ident = "HP Chromebook 11 G5 (Setzer)", |
| .matches = { |
| DMI_MATCH(DMI_SYS_VENDOR, "HP"), |
| DMI_MATCH(DMI_PRODUCT_NAME, "Setzer"), |
| }, |
| }, |
| { |
| .ident = "Acer Chromebook R11 (Cyan)", |
| .matches = { |
| DMI_MATCH(DMI_SYS_VENDOR, "GOOGLE"), |
| DMI_MATCH(DMI_PRODUCT_NAME, "Cyan"), |
| }, |
| }, |
| { |
| .ident = "Samsung Chromebook 3 (Celes)", |
| .matches = { |
| DMI_MATCH(DMI_SYS_VENDOR, "GOOGLE"), |
| DMI_MATCH(DMI_PRODUCT_NAME, "Celes"), |
| }, |
| }, |
| {} |
| }; |
| |
| static int chv_gpio_probe(struct chv_pinctrl *pctrl, int irq) |
| { |
| const struct chv_gpio_pinrange *range; |
| struct gpio_chip *chip = &pctrl->chip; |
| bool need_valid_mask = !dmi_check_system(chv_no_valid_mask); |
| const struct chv_community *community = pctrl->community; |
| int ret, i, irq_base; |
| |
| *chip = chv_gpio_chip; |
| |
| chip->ngpio = community->pins[community->npins - 1].number + 1; |
| chip->label = dev_name(pctrl->dev); |
| chip->parent = pctrl->dev; |
| chip->base = -1; |
| chip->irq.need_valid_mask = need_valid_mask; |
| |
| ret = devm_gpiochip_add_data(pctrl->dev, chip, pctrl); |
| if (ret) { |
| dev_err(pctrl->dev, "Failed to register gpiochip\n"); |
| return ret; |
| } |
| |
| for (i = 0; i < community->ngpio_ranges; i++) { |
| range = &community->gpio_ranges[i]; |
| ret = gpiochip_add_pin_range(chip, dev_name(pctrl->dev), |
| range->base, range->base, |
| range->npins); |
| if (ret) { |
| dev_err(pctrl->dev, "failed to add GPIO pin range\n"); |
| return ret; |
| } |
| } |
| |
| /* Do not add GPIOs that can only generate GPEs to the IRQ domain */ |
| for (i = 0; i < community->npins; i++) { |
| const struct pinctrl_pin_desc *desc; |
| u32 intsel; |
| |
| desc = &community->pins[i]; |
| |
| intsel = readl(chv_padreg(pctrl, desc->number, CHV_PADCTRL0)); |
| intsel &= CHV_PADCTRL0_INTSEL_MASK; |
| intsel >>= CHV_PADCTRL0_INTSEL_SHIFT; |
| |
| if (need_valid_mask && intsel >= community->nirqs) |
| clear_bit(i, chip->irq.valid_mask); |
| } |
| |
| /* |
| * The same set of machines in chv_no_valid_mask[] have incorrectly |
| * configured GPIOs that generate spurious interrupts so we use |
| * this same list to apply another quirk for them. |
| * |
| * See also https://bugzilla.kernel.org/show_bug.cgi?id=197953. |
| */ |
| if (!need_valid_mask) { |
| /* |
| * Mask all interrupts the community is able to generate |
| * but leave the ones that can only generate GPEs unmasked. |
| */ |
| chv_writel(GENMASK(31, pctrl->community->nirqs), |
| pctrl->regs + CHV_INTMASK); |
| } |
| |
| /* Clear all interrupts */ |
| chv_writel(0xffff, pctrl->regs + CHV_INTSTAT); |
| |
| if (!need_valid_mask) { |
| irq_base = devm_irq_alloc_descs(pctrl->dev, -1, 0, |
| chip->ngpio, NUMA_NO_NODE); |
| if (irq_base < 0) { |
| dev_err(pctrl->dev, "Failed to allocate IRQ numbers\n"); |
| return irq_base; |
| } |
| } else { |
| irq_base = 0; |
| } |
| |
| ret = gpiochip_irqchip_add(chip, &chv_gpio_irqchip, irq_base, |
| handle_bad_irq, IRQ_TYPE_NONE); |
| if (ret) { |
| dev_err(pctrl->dev, "failed to add IRQ chip\n"); |
| return ret; |
| } |
| |
| gpiochip_set_chained_irqchip(chip, &chv_gpio_irqchip, irq, |
| chv_gpio_irq_handler); |
| return 0; |
| } |
| |
| static acpi_status chv_pinctrl_mmio_access_handler(u32 function, |
| acpi_physical_address address, u32 bits, u64 *value, |
| void *handler_context, void *region_context) |
| { |
| struct chv_pinctrl *pctrl = region_context; |
| unsigned long flags; |
| acpi_status ret = AE_OK; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| if (function == ACPI_WRITE) |
| chv_writel((u32)(*value), pctrl->regs + (u32)address); |
| else if (function == ACPI_READ) |
| *value = readl(pctrl->regs + (u32)address); |
| else |
| ret = AE_BAD_PARAMETER; |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return ret; |
| } |
| |
| static int chv_pinctrl_probe(struct platform_device *pdev) |
| { |
| struct chv_pinctrl *pctrl; |
| struct acpi_device *adev; |
| struct resource *res; |
| acpi_status status; |
| int ret, irq, i; |
| |
| adev = ACPI_COMPANION(&pdev->dev); |
| if (!adev) |
| return -ENODEV; |
| |
| pctrl = devm_kzalloc(&pdev->dev, sizeof(*pctrl), GFP_KERNEL); |
| if (!pctrl) |
| return -ENOMEM; |
| |
| for (i = 0; i < ARRAY_SIZE(chv_communities); i++) |
| if (!strcmp(adev->pnp.unique_id, chv_communities[i]->uid)) { |
| pctrl->community = chv_communities[i]; |
| break; |
| } |
| if (i == ARRAY_SIZE(chv_communities)) |
| return -ENODEV; |
| |
| pctrl->dev = &pdev->dev; |
| |
| #ifdef CONFIG_PM_SLEEP |
| pctrl->saved_pin_context = devm_kcalloc(pctrl->dev, |
| pctrl->community->npins, sizeof(*pctrl->saved_pin_context), |
| GFP_KERNEL); |
| if (!pctrl->saved_pin_context) |
| return -ENOMEM; |
| #endif |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| pctrl->regs = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(pctrl->regs)) |
| return PTR_ERR(pctrl->regs); |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) { |
| dev_err(&pdev->dev, "failed to get interrupt number\n"); |
| return irq; |
| } |
| |
| pctrl->pctldesc = chv_pinctrl_desc; |
| pctrl->pctldesc.name = dev_name(&pdev->dev); |
| pctrl->pctldesc.pins = pctrl->community->pins; |
| pctrl->pctldesc.npins = pctrl->community->npins; |
| |
| pctrl->pctldev = devm_pinctrl_register(&pdev->dev, &pctrl->pctldesc, |
| pctrl); |
| if (IS_ERR(pctrl->pctldev)) { |
| dev_err(&pdev->dev, "failed to register pinctrl driver\n"); |
| return PTR_ERR(pctrl->pctldev); |
| } |
| |
| ret = chv_gpio_probe(pctrl, irq); |
| if (ret) |
| return ret; |
| |
| status = acpi_install_address_space_handler(adev->handle, |
| pctrl->community->acpi_space_id, |
| chv_pinctrl_mmio_access_handler, |
| NULL, pctrl); |
| if (ACPI_FAILURE(status)) |
| dev_err(&pdev->dev, "failed to install ACPI addr space handler\n"); |
| |
| platform_set_drvdata(pdev, pctrl); |
| |
| return 0; |
| } |
| |
| static int chv_pinctrl_remove(struct platform_device *pdev) |
| { |
| struct chv_pinctrl *pctrl = platform_get_drvdata(pdev); |
| |
| acpi_remove_address_space_handler(ACPI_COMPANION(&pdev->dev), |
| pctrl->community->acpi_space_id, |
| chv_pinctrl_mmio_access_handler); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int chv_pinctrl_suspend_noirq(struct device *dev) |
| { |
| struct platform_device *pdev = to_platform_device(dev); |
| struct chv_pinctrl *pctrl = platform_get_drvdata(pdev); |
| unsigned long flags; |
| int i; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| pctrl->saved_intmask = readl(pctrl->regs + CHV_INTMASK); |
| |
| for (i = 0; i < pctrl->community->npins; i++) { |
| const struct pinctrl_pin_desc *desc; |
| struct chv_pin_context *ctx; |
| void __iomem *reg; |
| |
| desc = &pctrl->community->pins[i]; |
| if (chv_pad_locked(pctrl, desc->number)) |
| continue; |
| |
| ctx = &pctrl->saved_pin_context[i]; |
| |
| reg = chv_padreg(pctrl, desc->number, CHV_PADCTRL0); |
| ctx->padctrl0 = readl(reg) & ~CHV_PADCTRL0_GPIORXSTATE; |
| |
| reg = chv_padreg(pctrl, desc->number, CHV_PADCTRL1); |
| ctx->padctrl1 = readl(reg); |
| } |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return 0; |
| } |
| |
| static int chv_pinctrl_resume_noirq(struct device *dev) |
| { |
| struct platform_device *pdev = to_platform_device(dev); |
| struct chv_pinctrl *pctrl = platform_get_drvdata(pdev); |
| unsigned long flags; |
| int i; |
| |
| raw_spin_lock_irqsave(&chv_lock, flags); |
| |
| /* |
| * Mask all interrupts before restoring per-pin configuration |
| * registers because we don't know in which state BIOS left them |
| * upon exiting suspend. |
| */ |
| chv_writel(0, pctrl->regs + CHV_INTMASK); |
| |
| for (i = 0; i < pctrl->community->npins; i++) { |
| const struct pinctrl_pin_desc *desc; |
| const struct chv_pin_context *ctx; |
| void __iomem *reg; |
| u32 val; |
| |
| desc = &pctrl->community->pins[i]; |
| if (chv_pad_locked(pctrl, desc->number)) |
| continue; |
| |
| ctx = &pctrl->saved_pin_context[i]; |
| |
| /* Only restore if our saved state differs from the current */ |
| reg = chv_padreg(pctrl, desc->number, CHV_PADCTRL0); |
| val = readl(reg) & ~CHV_PADCTRL0_GPIORXSTATE; |
| if (ctx->padctrl0 != val) { |
| chv_writel(ctx->padctrl0, reg); |
| dev_dbg(pctrl->dev, "restored pin %2u ctrl0 0x%08x\n", |
| desc->number, readl(reg)); |
| } |
| |
| reg = chv_padreg(pctrl, desc->number, CHV_PADCTRL1); |
| val = readl(reg); |
| if (ctx->padctrl1 != val) { |
| chv_writel(ctx->padctrl1, reg); |
| dev_dbg(pctrl->dev, "restored pin %2u ctrl1 0x%08x\n", |
| desc->number, readl(reg)); |
| } |
| } |
| |
| /* |
| * Now that all pins are restored to known state, we can restore |
| * the interrupt mask register as well. |
| */ |
| chv_writel(0xffff, pctrl->regs + CHV_INTSTAT); |
| chv_writel(pctrl->saved_intmask, pctrl->regs + CHV_INTMASK); |
| |
| raw_spin_unlock_irqrestore(&chv_lock, flags); |
| |
| return 0; |
| } |
| #endif |
| |
| static const struct dev_pm_ops chv_pinctrl_pm_ops = { |
| SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(chv_pinctrl_suspend_noirq, |
| chv_pinctrl_resume_noirq) |
| }; |
| |
| static const struct acpi_device_id chv_pinctrl_acpi_match[] = { |
| { "INT33FF" }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(acpi, chv_pinctrl_acpi_match); |
| |
| static struct platform_driver chv_pinctrl_driver = { |
| .probe = chv_pinctrl_probe, |
| .remove = chv_pinctrl_remove, |
| .driver = { |
| .name = "cherryview-pinctrl", |
| .pm = &chv_pinctrl_pm_ops, |
| .acpi_match_table = chv_pinctrl_acpi_match, |
| }, |
| }; |
| |
| static int __init chv_pinctrl_init(void) |
| { |
| return platform_driver_register(&chv_pinctrl_driver); |
| } |
| subsys_initcall(chv_pinctrl_init); |
| |
| static void __exit chv_pinctrl_exit(void) |
| { |
| platform_driver_unregister(&chv_pinctrl_driver); |
| } |
| module_exit(chv_pinctrl_exit); |
| |
| MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>"); |
| MODULE_DESCRIPTION("Intel Cherryview/Braswell pinctrl driver"); |
| MODULE_LICENSE("GPL v2"); |