| /* |
| * Copyright (c) 2017 Andreas Färber |
| * |
| * This file is dual-licensed: you can use it either under the terms |
| * of the GPL or the X11 license, at your option. Note that this dual |
| * licensing only applies to this file, and not this project as a |
| * whole. |
| * |
| * a) This library is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of the |
| * License, or (at your option) any later version. |
| * |
| * This library is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * Or, alternatively, |
| * |
| * b) Permission is hereby granted, free of charge, to any person |
| * obtaining a copy of this software and associated documentation |
| * files (the "Software"), to deal in the Software without |
| * restriction, including without limitation the rights to use, |
| * copy, modify, merge, publish, distribute, sublicense, and/or |
| * sell copies of the Software, and to permit persons to whom the |
| * Software is furnished to do so, subject to the following |
| * conditions: |
| * |
| * The above copyright notice and this permission notice shall be |
| * included in all copies or substantial portions of the Software. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, |
| * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES |
| * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND |
| * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT |
| * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, |
| * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING |
| * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR |
| * OTHER DEALINGS IN THE SOFTWARE. |
| * |
| * SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| */ |
| |
| /dts-v1/; |
| |
| #include "meson-gxbb.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| |
| / { |
| compatible = "friendlyarm,nanopi-k2", "amlogic,meson-gxbb"; |
| |
| aliases { |
| serial0 = &uart_AO; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0 0x0 0x80000000>; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| stat { |
| label = "nanopi-k2:blue:stat"; |
| gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>; |
| default-state = "on"; |
| panic-indicator; |
| }; |
| }; |
| |
| vdd_5v: regulator-vdd-5v { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDD_5V"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| vddio_ao18: regulator-vddio-ao18 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDIO_AO18"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vddio_ao3v3: regulator-vddio-ao3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VDDIO_AO3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| vddio_tf: regulator-vddio-tf { |
| compatible = "regulator-gpio"; |
| |
| regulator-name = "VDDIO_TF"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>; |
| gpios-states = <0>; |
| |
| states = <3300000 0>, |
| <1800000 1>; |
| }; |
| |
| wifi_32k: wifi-32k { |
| compatible = "pwm-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ |
| }; |
| |
| sdio_pwrseq: sdio-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; |
| clocks = <&wifi_32k>; |
| clock-names = "ext_clock"; |
| }; |
| |
| vcc1v8: regulator-vcc1v8 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC1.8V"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| vcc3v3: regulator-vcc3v3 { |
| compatible = "regulator-fixed"; |
| regulator-name = "VCC3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| emmc_pwrseq: emmc-pwrseq { |
| compatible = "mmc-pwrseq-emmc"; |
| reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| ðmac { |
| status = "okay"; |
| pinctrl-0 = <ð_rgmii_pins>; |
| pinctrl-names = "default"; |
| |
| phy-handle = <ð_phy0>; |
| phy-mode = "rgmii"; |
| |
| amlogic,tx-delay-ns = <2>; |
| |
| snps,reset-gpio = <&gpio GPIOZ_14 0>; |
| snps,reset-delays-us = <0 10000 1000000>; |
| snps,reset-active-low; |
| |
| mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| eth_phy0: ethernet-phy@0 { |
| /* Realtek RTL8211F (0x001cc916) */ |
| reg = <0>; |
| }; |
| }; |
| }; |
| |
| &ir { |
| status = "okay"; |
| pinctrl-0 = <&remote_input_ao_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &pwm_ef { |
| status = "okay"; |
| pinctrl-0 = <&pwm_e_pins>; |
| pinctrl-names = "default"; |
| clocks = <&clkc CLKID_FCLK_DIV4>; |
| clock-names = "clkin0"; |
| }; |
| |
| &saradc { |
| status = "okay"; |
| vref-supply = <&vddio_ao18>; |
| }; |
| |
| /* SDIO */ |
| &sd_emmc_a { |
| status = "okay"; |
| pinctrl-0 = <&sdio_pins>, <&sdio_irq_pins>; |
| pinctrl-names = "default"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| max-frequency = <200000000>; |
| |
| non-removable; |
| disable-wp; |
| |
| mmc-pwrseq = <&sdio_pwrseq>; |
| |
| vmmc-supply = <&vddio_ao3v3>; |
| vqmmc-supply = <&vddio_ao18>; |
| |
| brcmf: wifi@1 { |
| compatible = "brcm,bcm4329-fmac"; |
| reg = <1>; |
| }; |
| }; |
| |
| /* SD */ |
| &sd_emmc_b { |
| status = "okay"; |
| pinctrl-0 = <&sdcard_pins>; |
| pinctrl-names = "default"; |
| |
| bus-width = <4>; |
| cap-sd-highspeed; |
| max-frequency = <100000000>; |
| disable-wp; |
| |
| cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; |
| cd-inverted; |
| |
| vmmc-supply = <&vddio_ao3v3>; |
| vqmmc-supply = <&vddio_tf>; |
| }; |
| |
| /* eMMC */ |
| &sd_emmc_c { |
| status = "disabled"; |
| pinctrl-0 = <&emmc_pins>; |
| pinctrl-names = "default"; |
| |
| bus-width = <8>; |
| cap-sd-highspeed; |
| max-frequency = <200000000>; |
| non-removable; |
| disable-wp; |
| cap-mmc-highspeed; |
| mmc-ddr-1_8v; |
| mmc-hs200-1_8v; |
| |
| mmc-pwrseq = <&emmc_pwrseq>; |
| vmmc-supply = <&vcc3v3>; |
| vqmmc-supply = <&vcc1v8>; |
| }; |
| |
| /* DBG_UART */ |
| &uart_AO { |
| status = "okay"; |
| pinctrl-0 = <&uart_ao_a_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| /* Bluetooth on AP6212 */ |
| &uart_A { |
| status = "disabled"; |
| pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| /* 40-pin CON1 */ |
| &uart_C { |
| status = "disabled"; |
| pinctrl-0 = <&uart_c_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &usb0_phy { |
| status = "okay"; |
| phy-supply = <&vdd_5v>; |
| }; |
| |
| &usb1_phy { |
| status = "okay"; |
| }; |
| |
| &usb0 { |
| status = "okay"; |
| }; |
| |
| &usb1 { |
| status = "okay"; |
| }; |