drivers/iio/pressure/bmp280.c

/*
 * Copyright (c) 2014 Intel Corporation
 *
 * Driver for Bosch Sensortec BMP180 and BMP280 digital pressure sensor.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 * Datasheet:
 * https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BMP180-DS000-121.pdf
 * https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BMP280-DS001-12.pdf
 * https://ae-bst.resource.bosch.com/media/_tech/media/datasheets/BST-BME280_DS001-11.pdf
 */

#define pr_fmt(fmt) "bmp280: " fmt

#include <linux/module.h>
#include <linux/i2c.h>
#include <linux/acpi.h>
#include <linux/regmap.h>
#include <linux/delay.h>
#include <linux/iio/iio.h>
#include <linux/iio/sysfs.h>

/* BMP280 specific registers */
#define BMP280_REG_HUMIDITY_LSB		0xFE
#define BMP280_REG_HUMIDITY_MSB		0xFD
#define BMP280_REG_TEMP_XLSB		0xFC
#define BMP280_REG_TEMP_LSB		0xFB
#define BMP280_REG_TEMP_MSB		0xFA
#define BMP280_REG_PRESS_XLSB		0xF9
#define BMP280_REG_PRESS_LSB		0xF8
#define BMP280_REG_PRESS_MSB		0xF7

#define BMP280_REG_CONFIG		0xF5
#define BMP280_REG_CTRL_MEAS		0xF4
#define BMP280_REG_STATUS		0xF3
#define BMP280_REG_CTRL_HUMIDITY	0xF2

/* Due to non linear mapping, and data sizes we can't do a bulk read */
#define BMP280_REG_COMP_H1		0xA1
#define BMP280_REG_COMP_H2		0xE1
#define BMP280_REG_COMP_H3		0xE3
#define BMP280_REG_COMP_H4		0xE4
#define BMP280_REG_COMP_H5		0xE5
#define BMP280_REG_COMP_H6		0xE7

#define BMP280_REG_COMP_TEMP_START	0x88
#define BMP280_COMP_TEMP_REG_COUNT	6

#define BMP280_REG_COMP_PRESS_START	0x8E
#define BMP280_COMP_PRESS_REG_COUNT	18

#define BMP280_FILTER_MASK		(BIT(4) | BIT(3) | BIT(2))
#define BMP280_FILTER_OFF		0
#define BMP280_FILTER_2X		BIT(2)
#define BMP280_FILTER_4X		BIT(3)
#define BMP280_FILTER_8X		(BIT(3) | BIT(2))
#define BMP280_FILTER_16X		BIT(4)

#define BMP280_OSRS_HUMIDITY_MASK	(BIT(2) | BIT(1) | BIT(0))
#define BMP280_OSRS_HUMIDITIY_X(osrs_h)	((osrs_h) << 0)
#define BMP280_OSRS_HUMIDITY_SKIP	0
#define BMP280_OSRS_HUMIDITY_1X		BMP280_OSRS_HUMIDITIY_X(1)
#define BMP280_OSRS_HUMIDITY_2X		BMP280_OSRS_HUMIDITIY_X(2)
#define BMP280_OSRS_HUMIDITY_4X		BMP280_OSRS_HUMIDITIY_X(3)
#define BMP280_OSRS_HUMIDITY_8X		BMP280_OSRS_HUMIDITIY_X(4)
#define BMP280_OSRS_HUMIDITY_16X	BMP280_OSRS_HUMIDITIY_X(5)

#define BMP280_OSRS_TEMP_MASK		(BIT(7) | BIT(6) | BIT(5))
#define BMP280_OSRS_TEMP_SKIP		0
#define BMP280_OSRS_TEMP_X(osrs_t)	((osrs_t) << 5)
#define BMP280_OSRS_TEMP_1X		BMP280_OSRS_TEMP_X(1)
#define BMP280_OSRS_TEMP_2X		BMP280_OSRS_TEMP_X(2)
#define BMP280_OSRS_TEMP_4X		BMP280_OSRS_TEMP_X(3)
#define BMP280_OSRS_TEMP_8X		BMP280_OSRS_TEMP_X(4)
#define BMP280_OSRS_TEMP_16X		BMP280_OSRS_TEMP_X(5)

#define BMP280_OSRS_PRESS_MASK		(BIT(4) | BIT(3) | BIT(2))
#define BMP280_OSRS_PRESS_SKIP		0
#define BMP280_OSRS_PRESS_X(osrs_p)	((osrs_p) << 2)
#define BMP280_OSRS_PRESS_1X		BMP280_OSRS_PRESS_X(1)
#define BMP280_OSRS_PRESS_2X		BMP280_OSRS_PRESS_X(2)
#define BMP280_OSRS_PRESS_4X		BMP280_OSRS_PRESS_X(3)
#define BMP280_OSRS_PRESS_8X		BMP280_OSRS_PRESS_X(4)
#define BMP280_OSRS_PRESS_16X		BMP280_OSRS_PRESS_X(5)

#define BMP280_MODE_MASK		(BIT(1) | BIT(0))
#define BMP280_MODE_SLEEP		0
#define BMP280_MODE_FORCED		BIT(0)
#define BMP280_MODE_NORMAL		(BIT(1) | BIT(0))

/* BMP180 specific registers */
#define BMP180_REG_OUT_XLSB		0xF8
#define BMP180_REG_OUT_LSB		0xF7
#define BMP180_REG_OUT_MSB		0xF6

#define BMP180_REG_CALIB_START		0xAA
#define BMP180_REG_CALIB_COUNT		22

#define BMP180_MEAS_SCO			BIT(5)
#define BMP180_MEAS_TEMP		(0x0E | BMP180_MEAS_SCO)
#define BMP180_MEAS_PRESS_X(oss)	((oss) << 6 | 0x14 | BMP180_MEAS_SCO)
#define BMP180_MEAS_PRESS_1X		BMP180_MEAS_PRESS_X(0)
#define BMP180_MEAS_PRESS_2X		BMP180_MEAS_PRESS_X(1)
#define BMP180_MEAS_PRESS_4X		BMP180_MEAS_PRESS_X(2)
#define BMP180_MEAS_PRESS_8X		BMP180_MEAS_PRESS_X(3)

/* BMP180 and BMP280 common registers */
#define BMP280_REG_CTRL_MEAS		0xF4
#define BMP280_REG_RESET		0xE0
#define BMP280_REG_ID			0xD0

#define BMP180_CHIP_ID			0x55
#define BMP280_CHIP_ID			0x58
#define BME280_CHIP_ID			0x60
#define BMP280_SOFT_RESET_VAL		0xB6

struct bmp280_data {
	struct i2c_client *client;
	struct mutex lock;
	struct regmap *regmap;
	const struct bmp280_chip_info *chip_info;

	/* log of base 2 of oversampling rate */
	u8 oversampling_press;
	u8 oversampling_temp;
	u8 oversampling_humid;

	/*
	 * Carryover value from temperature conversion, used in pressure
	 * calculation.
	 */
	s32 t_fine;
};

struct bmp280_chip_info {
	const struct regmap_config *regmap_config;

	const int *oversampling_temp_avail;
	int num_oversampling_temp_avail;

	const int *oversampling_press_avail;
	int num_oversampling_press_avail;

	const int *oversampling_humid_avail;
	int num_oversampling_humid_avail;

	int (*chip_config)(struct bmp280_data *);
	int (*read_temp)(struct bmp280_data *, int *);
	int (*read_press)(struct bmp280_data *, int *, int *);
	int (*read_humid)(struct bmp280_data *, int *, int *);
};

/*
 * These enums are used for indexing into the array of compensation
 * parameters for BMP280.
 */
enum { T1, T2, T3 };
enum { P1, P2, P3, P4, P5, P6, P7, P8, P9 };

static const struct iio_chan_spec bmp280_channels[] = {
	{
		.type = IIO_PRESSURE,
		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
	},
	{
		.type = IIO_TEMP,
		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
	},
	{
		.type = IIO_HUMIDITYRELATIVE,
		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) |
				      BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO),
	},
};

static bool bmp280_is_writeable_reg(struct device *dev, unsigned int reg)
{
	switch (reg) {
	case BMP280_REG_CONFIG:
	case BMP280_REG_CTRL_HUMIDITY:
	case BMP280_REG_CTRL_MEAS:
	case BMP280_REG_RESET:
		return true;
	default:
		return false;
	};
}

static bool bmp280_is_volatile_reg(struct device *dev, unsigned int reg)
{
	switch (reg) {
	case BMP280_REG_HUMIDITY_LSB:
	case BMP280_REG_HUMIDITY_MSB:
	case BMP280_REG_TEMP_XLSB:
	case BMP280_REG_TEMP_LSB:
	case BMP280_REG_TEMP_MSB:
	case BMP280_REG_PRESS_XLSB:
	case BMP280_REG_PRESS_LSB:
	case BMP280_REG_PRESS_MSB:
	case BMP280_REG_STATUS:
		return true;
	default:
		return false;
	}
}

static const struct regmap_config bmp280_regmap_config = {
	.reg_bits = 8,
	.val_bits = 8,

	.max_register = BMP280_REG_HUMIDITY_LSB,
	.cache_type = REGCACHE_RBTREE,

	.writeable_reg = bmp280_is_writeable_reg,
	.volatile_reg = bmp280_is_volatile_reg,
};

/*
 * Returns humidity in percent, resolution is 0.01 percent. Output value of
 * "47445" represents 47445/1024 = 46.333 %RH.
 *
 * Taken from BME280 datasheet, Section 4.2.3, "Compensation formula".
 */

static u32 bmp280_compensate_humidity(struct bmp280_data *data,
				      s32 adc_humidity)
{
	struct device *dev = &data->client->dev;
	unsigned int H1, H3, tmp;
	int H2, H4, H5, H6, ret, var;

	ret = regmap_read(data->regmap, BMP280_REG_COMP_H1, &H1);
	if (ret < 0) {
		dev_err(dev, "failed to read H1 comp value\n");
		return ret;
	}

	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_H2, &tmp, 2);
	if (ret < 0) {
		dev_err(dev, "failed to read H2 comp value\n");
		return ret;
	}
	H2 = sign_extend32(le16_to_cpu(tmp), 15);

	ret = regmap_read(data->regmap, BMP280_REG_COMP_H3, &H3);
	if (ret < 0) {
		dev_err(dev, "failed to read H3 comp value\n");
		return ret;
	}

	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_H4, &tmp, 2);
	if (ret < 0) {
		dev_err(dev, "failed to read H4 comp value\n");
		return ret;
	}
	H4 = sign_extend32(((be16_to_cpu(tmp) >> 4) & 0xff0) |
			  (be16_to_cpu(tmp) & 0xf), 11);

	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_H5, &tmp, 2);
	if (ret < 0) {
		dev_err(dev, "failed to read H5 comp value\n");
		return ret;
	}
	H5 = sign_extend32(((le16_to_cpu(tmp) >> 4) & 0xfff), 11);

	ret = regmap_read(data->regmap, BMP280_REG_COMP_H6, &tmp);
	if (ret < 0) {
		dev_err(dev, "failed to read H6 comp value\n");
		return ret;
	}
	H6 = sign_extend32(tmp, 7);

	var = ((s32)data->t_fine) - 76800;
	var = ((((adc_humidity << 14) - (H4 << 20) - (H5 * var)) + 16384) >> 15)
		* (((((((var * H6) >> 10) * (((var * H3) >> 11) + 32768)) >> 10)
		+ 2097152) * H2 + 8192) >> 14);
	var -= ((((var >> 15) * (var >> 15)) >> 7) * H1) >> 4;

	return var >> 12;
};

/*
 * Returns temperature in DegC, resolution is 0.01 DegC.  Output value of
 * "5123" equals 51.23 DegC.  t_fine carries fine temperature as global
 * value.
 *
 * Taken from datasheet, Section 3.11.3, "Compensation formula".
 */
static s32 bmp280_compensate_temp(struct bmp280_data *data,
				  s32 adc_temp)
{
	int ret;
	s32 var1, var2;
	__le16 buf[BMP280_COMP_TEMP_REG_COUNT / 2];

	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_TEMP_START,
			       buf, BMP280_COMP_TEMP_REG_COUNT);
	if (ret < 0) {
		dev_err(&data->client->dev,
			"failed to read temperature calibration parameters\n");
		return ret;
	}

	/*
	 * The double casts are necessary because le16_to_cpu returns an
	 * unsigned 16-bit value.  Casting that value directly to a
	 * signed 32-bit will not do proper sign extension.
	 *
	 * Conversely, T1 and P1 are unsigned values, so they can be
	 * cast straight to the larger type.
	 */
	var1 = (((adc_temp >> 3) - ((s32)le16_to_cpu(buf[T1]) << 1)) *
		((s32)(s16)le16_to_cpu(buf[T2]))) >> 11;
	var2 = (((((adc_temp >> 4) - ((s32)le16_to_cpu(buf[T1]))) *
		  ((adc_temp >> 4) - ((s32)le16_to_cpu(buf[T1])))) >> 12) *
		((s32)(s16)le16_to_cpu(buf[T3]))) >> 14;
	data->t_fine = var1 + var2;

	return (data->t_fine * 5 + 128) >> 8;
}

/*
 * Returns pressure in Pa as unsigned 32 bit integer in Q24.8 format (24
 * integer bits and 8 fractional bits).  Output value of "24674867"
 * represents 24674867/256 = 96386.2 Pa = 963.862 hPa
 *
 * Taken from datasheet, Section 3.11.3, "Compensation formula".
 */
static u32 bmp280_compensate_press(struct bmp280_data *data,
				   s32 adc_press)
{
	int ret;
	s64 var1, var2, p;
	__le16 buf[BMP280_COMP_PRESS_REG_COUNT / 2];

	ret = regmap_bulk_read(data->regmap, BMP280_REG_COMP_PRESS_START,
			       buf, BMP280_COMP_PRESS_REG_COUNT);
	if (ret < 0) {
		dev_err(&data->client->dev,
			"failed to read pressure calibration parameters\n");
		return ret;
	}

	var1 = ((s64)data->t_fine) - 128000;
	var2 = var1 * var1 * (s64)(s16)le16_to_cpu(buf[P6]);
	var2 += (var1 * (s64)(s16)le16_to_cpu(buf[P5])) << 17;
	var2 += ((s64)(s16)le16_to_cpu(buf[P4])) << 35;
	var1 = ((var1 * var1 * (s64)(s16)le16_to_cpu(buf[P3])) >> 8) +
		((var1 * (s64)(s16)le16_to_cpu(buf[P2])) << 12);
	var1 = ((((s64)1) << 47) + var1) * ((s64)le16_to_cpu(buf[P1])) >> 33;

	if (var1 == 0)
		return 0;

	p = ((((s64)1048576 - adc_press) << 31) - var2) * 3125;
	p = div64_s64(p, var1);
	var1 = (((s64)(s16)le16_to_cpu(buf[P9])) * (p >> 13) * (p >> 13)) >> 25;
	var2 = (((s64)(s16)le16_to_cpu(buf[P8])) * p) >> 19;
	p = ((p + var1 + var2) >> 8) + (((s64)(s16)le16_to_cpu(buf[P7])) << 4);

	return (u32)p;
}

static int bmp280_read_temp(struct bmp280_data *data,
			    int *val)
{
	int ret;
	__be32 tmp = 0;
	s32 adc_temp, comp_temp;

	ret = regmap_bulk_read(data->regmap, BMP280_REG_TEMP_MSB,
			       (u8 *) &tmp, 3);
	if (ret < 0) {
		dev_err(&data->client->dev, "failed to read temperature\n");
		return ret;
	}

	adc_temp = be32_to_cpu(tmp) >> 12;
	comp_temp = bmp280_compensate_temp(data, adc_temp);

	/*
	 * val might be NULL if we're called by the read_press routine,
	 * who only cares about the carry over t_fine value.
	 */
	if (val) {
		*val = comp_temp * 10;
		return IIO_VAL_INT;
	}

	return 0;
}

static int bmp280_read_press(struct bmp280_data *data,
			     int *val, int *val2)
{
	int ret;
	__be32 tmp = 0;
	s32 adc_press;
	u32 comp_press;

	/* Read and compensate temperature so we get a reading of t_fine. */
	ret = bmp280_read_temp(data, NULL);
	if (ret < 0)
		return ret;

	ret = regmap_bulk_read(data->regmap, BMP280_REG_PRESS_MSB,
			       (u8 *) &tmp, 3);
	if (ret < 0) {
		dev_err(&data->client->dev, "failed to read pressure\n");
		return ret;
	}

	adc_press = be32_to_cpu(tmp) >> 12;
	comp_press = bmp280_compensate_press(data, adc_press);

	*val = comp_press;
	*val2 = 256000;

	return IIO_VAL_FRACTIONAL;
}

static int bmp280_read_humid(struct bmp280_data *data, int *val, int *val2)
{
	int ret;
	__be16 tmp = 0;
	s32 adc_humidity;
	u32 comp_humidity;

	/* Read and compensate temperature so we get a reading of t_fine. */
	ret = bmp280_read_temp(data, NULL);
	if (ret < 0)
		return ret;

	ret = regmap_bulk_read(data->regmap, BMP280_REG_HUMIDITY_MSB,
			       (u8 *) &tmp, 2);
	if (ret < 0) {
		dev_err(&data->client->dev, "failed to read humidity\n");
		return ret;
	}

	adc_humidity = be16_to_cpu(tmp);
	comp_humidity = bmp280_compensate_humidity(data, adc_humidity);

	*val = comp_humidity;
	*val2 = 1024;

	return IIO_VAL_FRACTIONAL;
}

static int bmp280_read_raw(struct iio_dev *indio_dev,
			   struct iio_chan_spec const *chan,
			   int *val, int *val2, long mask)
{
	int ret;
	struct bmp280_data *data = iio_priv(indio_dev);

	mutex_lock(&data->lock);

	switch (mask) {
	case IIO_CHAN_INFO_PROCESSED:
		switch (chan->type) {
		case IIO_HUMIDITYRELATIVE:
			ret = data->chip_info->read_humid(data, val, val2);
			break;
		case IIO_PRESSURE:
			ret = data->chip_info->read_press(data, val, val2);
			break;
		case IIO_TEMP:
			ret = data->chip_info->read_temp(data, val);
			break;
		default:
			ret = -EINVAL;
			break;
		}
		break;
	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
		switch (chan->type) {
		case IIO_HUMIDITYRELATIVE:
			*val = 1 << data->oversampling_humid;
			ret = IIO_VAL_INT;
			break;
		case IIO_PRESSURE:
			*val = 1 << data->oversampling_press;
			ret = IIO_VAL_INT;
			break;
		case IIO_TEMP:
			*val = 1 << data->oversampling_temp;
			ret = IIO_VAL_INT;
			break;
		default:
			ret = -EINVAL;
			break;
		}
		break;
	default:
		ret = -EINVAL;
		break;
	}

	mutex_unlock(&data->lock);

	return ret;
}

static int bmp280_write_oversampling_ratio_humid(struct bmp280_data *data,
					       int val)
{
	int i;
	const int *avail = data->chip_info->oversampling_humid_avail;
	const int n = data->chip_info->num_oversampling_humid_avail;

	for (i = 0; i < n; i++) {
		if (avail[i] == val) {
			data->oversampling_humid = ilog2(val);

			return data->chip_info->chip_config(data);
		}
	}
	return -EINVAL;
}

static int bmp280_write_oversampling_ratio_temp(struct bmp280_data *data,
					       int val)
{
	int i;
	const int *avail = data->chip_info->oversampling_temp_avail;
	const int n = data->chip_info->num_oversampling_temp_avail;

	for (i = 0; i < n; i++) {
		if (avail[i] == val) {
			data->oversampling_temp = ilog2(val);

			return data->chip_info->chip_config(data);
		}
	}
	return -EINVAL;
}

static int bmp280_write_oversampling_ratio_press(struct bmp280_data *data,
					       int val)
{
	int i;
	const int *avail = data->chip_info->oversampling_press_avail;
	const int n = data->chip_info->num_oversampling_press_avail;

	for (i = 0; i < n; i++) {
		if (avail[i] == val) {
			data->oversampling_press = ilog2(val);

			return data->chip_info->chip_config(data);
		}
	}
	return -EINVAL;
}

static int bmp280_write_raw(struct iio_dev *indio_dev,
			    struct iio_chan_spec const *chan,
			    int val, int val2, long mask)
{
	int ret = 0;
	struct bmp280_data *data = iio_priv(indio_dev);

	switch (mask) {
	case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
		mutex_lock(&data->lock);
		switch (chan->type) {
		case IIO_HUMIDITYRELATIVE:
			ret = bmp280_write_oversampling_ratio_humid(data, val);
			break;
		case IIO_PRESSURE:
			ret = bmp280_write_oversampling_ratio_press(data, val);
			break;
		case IIO_TEMP:
			ret = bmp280_write_oversampling_ratio_temp(data, val);
			break;
		default:
			ret = -EINVAL;
			break;
		}
		mutex_unlock(&data->lock);
		break;
	default:
		return -EINVAL;
	}

	return ret;
}

static ssize_t bmp280_show_avail(char *buf, const int *vals, const int n)
{
	size_t len = 0;
	int i;

	for (i = 0; i < n; i++)
		len += scnprintf(buf + len, PAGE_SIZE - len, "%d ", vals[i]);

	buf[len - 1] = '\n';

	return len;
}

static ssize_t bmp280_show_temp_oversampling_avail(struct device *dev,
				struct device_attribute *attr, char *buf)
{
	struct bmp280_data *data = iio_priv(dev_to_iio_dev(dev));

	return bmp280_show_avail(buf, data->chip_info->oversampling_temp_avail,
				 data->chip_info->num_oversampling_temp_avail);
}

static ssize_t bmp280_show_press_oversampling_avail(struct device *dev,
				struct device_attribute *attr, char *buf)
{
	struct bmp280_data *data = iio_priv(dev_to_iio_dev(dev));

	return bmp280_show_avail(buf, data->chip_info->oversampling_press_avail,
				 data->chip_info->num_oversampling_press_avail);
}

static IIO_DEVICE_ATTR(in_temp_oversampling_ratio_available,
	S_IRUGO, bmp280_show_temp_oversampling_avail, NULL, 0);

static IIO_DEVICE_ATTR(in_pressure_oversampling_ratio_available,
	S_IRUGO, bmp280_show_press_oversampling_avail, NULL, 0);

static struct attribute *bmp280_attributes[] = {
	&iio_dev_attr_in_temp_oversampling_ratio_available.dev_attr.attr,
	&iio_dev_attr_in_pressure_oversampling_ratio_available.dev_attr.attr,
	NULL,
};

static const struct attribute_group bmp280_attrs_group = {
	.attrs = bmp280_attributes,
};

static const struct iio_info bmp280_info = {
	.driver_module = THIS_MODULE,
	.read_raw = &bmp280_read_raw,
	.write_raw = &bmp280_write_raw,
	.attrs = &bmp280_attrs_group,
};

static int bmp280_chip_config(struct bmp280_data *data)
{
	int ret;
	u8 osrs = BMP280_OSRS_TEMP_X(data->oversampling_temp + 1) |
		  BMP280_OSRS_PRESS_X(data->oversampling_press + 1);

	ret = regmap_update_bits(data->regmap, BMP280_REG_CTRL_MEAS,
				 BMP280_OSRS_TEMP_MASK |
				 BMP280_OSRS_PRESS_MASK |
				 BMP280_MODE_MASK,
				 osrs | BMP280_MODE_NORMAL);
	if (ret < 0) {
		dev_err(&data->client->dev,
			"failed to write ctrl_meas register\n");
		return ret;
	}

	ret = regmap_update_bits(data->regmap, BMP280_REG_CONFIG,
				 BMP280_FILTER_MASK,
				 BMP280_FILTER_4X);
	if (ret < 0) {
		dev_err(&data->client->dev,
			"failed to write config register\n");
		return ret;
	}

	return ret;
}

static const int bmp280_oversampling_avail[] = { 1, 2, 4, 8, 16 };

static const struct bmp280_chip_info bmp280_chip_info = {
	.regmap_config = &bmp280_regmap_config,

	.oversampling_temp_avail = bmp280_oversampling_avail,
	.num_oversampling_temp_avail = ARRAY_SIZE(bmp280_oversampling_avail),

	.oversampling_press_avail = bmp280_oversampling_avail,
	.num_oversampling_press_avail = ARRAY_SIZE(bmp280_oversampling_avail),

	.chip_config = bmp280_chip_config,
	.read_temp = bmp280_read_temp,
	.read_press = bmp280_read_press,
};

static int bme280_chip_config(struct bmp280_data *data)
{
	int ret = bmp280_chip_config(data);
	u8 osrs = BMP280_OSRS_HUMIDITIY_X(data->oversampling_humid + 1);

	if (ret < 0)
		return ret;

	return regmap_update_bits(data->regmap, BMP280_REG_CTRL_HUMIDITY,
				  BMP280_OSRS_HUMIDITY_MASK, osrs);
}

static const struct bmp280_chip_info bme280_chip_info = {
	.regmap_config = &bmp280_regmap_config,

	.oversampling_temp_avail = bmp280_oversampling_avail,
	.num_oversampling_temp_avail = ARRAY_SIZE(bmp280_oversampling_avail),

	.oversampling_press_avail = bmp280_oversampling_avail,
	.num_oversampling_press_avail = ARRAY_SIZE(bmp280_oversampling_avail),

	.oversampling_humid_avail = bmp280_oversampling_avail,
	.num_oversampling_humid_avail = ARRAY_SIZE(bmp280_oversampling_avail),

	.chip_config = bme280_chip_config,
	.read_temp = bmp280_read_temp,
	.read_press = bmp280_read_press,
	.read_humid = bmp280_read_humid,
};


static bool bmp180_is_writeable_reg(struct device *dev, unsigned int reg)
{
	switch (reg) {
	case BMP280_REG_CTRL_MEAS:
	case BMP280_REG_RESET:
		return true;
	default:
		return false;
	};
}

static bool bmp180_is_volatile_reg(struct device *dev, unsigned int reg)
{
	switch (reg) {
	case BMP180_REG_OUT_XLSB:
	case BMP180_REG_OUT_LSB:
	case BMP180_REG_OUT_MSB:
	case BMP280_REG_CTRL_MEAS:
		return true;
	default:
		return false;
	}
}

static const struct regmap_config bmp180_regmap_config = {
	.reg_bits = 8,
	.val_bits = 8,

	.max_register = BMP180_REG_OUT_XLSB,
	.cache_type = REGCACHE_RBTREE,

	.writeable_reg = bmp180_is_writeable_reg,
	.volatile_reg = bmp180_is_volatile_reg,
};

static int bmp180_measure(struct bmp280_data *data, u8 ctrl_meas)
{
	int ret;
	const int conversion_time_max[] = { 4500, 7500, 13500, 25500 };
	unsigned int delay_us;
	unsigned int ctrl;

	ret = regmap_write(data->regmap, BMP280_REG_CTRL_MEAS, ctrl_meas);
	if (ret)
		return ret;

	if (ctrl_meas == BMP180_MEAS_TEMP)
		delay_us = 4500;
	else
		delay_us = conversion_time_max[data->oversampling_press];

	usleep_range(delay_us, delay_us + 1000);

	ret = regmap_read(data->regmap, BMP280_REG_CTRL_MEAS, &ctrl);
	if (ret)
		return ret;

	/* The value of this bit reset to "0" after conversion is complete */
	if (ctrl & BMP180_MEAS_SCO)
		return -EIO;

	return 0;
}

static int bmp180_read_adc_temp(struct bmp280_data *data, int *val)
{
	int ret;
	__be16 tmp = 0;

	ret = bmp180_measure(data, BMP180_MEAS_TEMP);
	if (ret)
		return ret;

	ret = regmap_bulk_read(data->regmap, BMP180_REG_OUT_MSB, (u8 *)&tmp, 2);
	if (ret)
		return ret;

	*val = be16_to_cpu(tmp);

	return 0;
}

/*
 * These enums are used for indexing into the array of calibration
 * coefficients for BMP180.
 */
enum { AC1, AC2, AC3, AC4, AC5, AC6, B1, B2, MB, MC, MD };

struct bmp180_calib {
	s16 AC1;
	s16 AC2;
	s16 AC3;
	u16 AC4;
	u16 AC5;
	u16 AC6;
	s16 B1;
	s16 B2;
	s16 MB;
	s16 MC;
	s16 MD;
};

static int bmp180_read_calib(struct bmp280_data *data,
			     struct bmp180_calib *calib)
{
	int ret;
	int i;
	__be16 buf[BMP180_REG_CALIB_COUNT / 2];

	ret = regmap_bulk_read(data->regmap, BMP180_REG_CALIB_START, buf,
			       sizeof(buf));

	if (ret < 0)
		return ret;

	/* None of the words has the value 0 or 0xFFFF */
	for (i = 0; i < ARRAY_SIZE(buf); i++) {
		if (buf[i] == cpu_to_be16(0) || buf[i] == cpu_to_be16(0xffff))
			return -EIO;
	}

	calib->AC1 = be16_to_cpu(buf[AC1]);
	calib->AC2 = be16_to_cpu(buf[AC2]);
	calib->AC3 = be16_to_cpu(buf[AC3]);
	calib->AC4 = be16_to_cpu(buf[AC4]);
	calib->AC5 = be16_to_cpu(buf[AC5]);
	calib->AC6 = be16_to_cpu(buf[AC6]);
	calib->B1 = be16_to_cpu(buf[B1]);
	calib->B2 = be16_to_cpu(buf[B2]);
	calib->MB = be16_to_cpu(buf[MB]);
	calib->MC = be16_to_cpu(buf[MC]);
	calib->MD = be16_to_cpu(buf[MD]);

	return 0;
}

/*
 * Returns temperature in DegC, resolution is 0.1 DegC.
 * t_fine carries fine temperature as global value.
 *
 * Taken from datasheet, Section 3.5, "Calculating pressure and temperature".
 */
static s32 bmp180_compensate_temp(struct bmp280_data *data, s32 adc_temp)
{
	int ret;
	s32 x1, x2;
	struct bmp180_calib calib;

	ret = bmp180_read_calib(data, &calib);
	if (ret < 0) {
		dev_err(&data->client->dev,
			"failed to read calibration coefficients\n");
		return ret;
	}

	x1 = ((adc_temp - calib.AC6) * calib.AC5) >> 15;
	x2 = (calib.MC << 11) / (x1 + calib.MD);
	data->t_fine = x1 + x2;

	return (data->t_fine + 8) >> 4;
}

static int bmp180_read_temp(struct bmp280_data *data, int *val)
{
	int ret;
	s32 adc_temp, comp_temp;

	ret = bmp180_read_adc_temp(data, &adc_temp);
	if (ret)
		return ret;

	comp_temp = bmp180_compensate_temp(data, adc_temp);

	/*
	 * val might be NULL if we're called by the read_press routine,
	 * who only cares about the carry over t_fine value.
	 */
	if (val) {
		*val = comp_temp * 100;
		return IIO_VAL_INT;
	}

	return 0;
}

static int bmp180_read_adc_press(struct bmp280_data *data, int *val)
{
	int ret;
	__be32 tmp = 0;
	u8 oss = data->oversampling_press;

	ret = bmp180_measure(data, BMP180_MEAS_PRESS_X(oss));
	if (ret)
		return ret;

	ret = regmap_bulk_read(data->regmap, BMP180_REG_OUT_MSB, (u8 *)&tmp, 3);
	if (ret)
		return ret;

	*val = (be32_to_cpu(tmp) >> 8) >> (8 - oss);

	return 0;
}

/*
 * Returns pressure in Pa, resolution is 1 Pa.
 *
 * Taken from datasheet, Section 3.5, "Calculating pressure and temperature".
 */
static u32 bmp180_compensate_press(struct bmp280_data *data, s32 adc_press)
{
	int ret;
	s32 x1, x2, x3, p;
	s32 b3, b6;
	u32 b4, b7;
	s32 oss = data->oversampling_press;
	struct bmp180_calib calib;

	ret = bmp180_read_calib(data, &calib);
	if (ret < 0) {
		dev_err(&data->client->dev,
			"failed to read calibration coefficients\n");
		return ret;
	}

	b6 = data->t_fine - 4000;
	x1 = (calib.B2 * (b6 * b6 >> 12)) >> 11;
	x2 = calib.AC2 * b6 >> 11;
	x3 = x1 + x2;
	b3 = ((((s32)calib.AC1 * 4 + x3) << oss) + 2) / 4;
	x1 = calib.AC3 * b6 >> 13;
	x2 = (calib.B1 * ((b6 * b6) >> 12)) >> 16;
	x3 = (x1 + x2 + 2) >> 2;
	b4 = calib.AC4 * (u32)(x3 + 32768) >> 15;
	b7 = ((u32)adc_press - b3) * (50000 >> oss);
	if (b7 < 0x80000000)
		p = (b7 * 2) / b4;
	else
		p = (b7 / b4) * 2;

	x1 = (p >> 8) * (p >> 8);
	x1 = (x1 * 3038) >> 16;
	x2 = (-7357 * p) >> 16;

	return p + ((x1 + x2 + 3791) >> 4);
}

static int bmp180_read_press(struct bmp280_data *data,
			     int *val, int *val2)
{
	int ret;
	s32 adc_press;
	u32 comp_press;

	/* Read and compensate temperature so we get a reading of t_fine. */
	ret = bmp180_read_temp(data, NULL);
	if (ret)
		return ret;

	ret = bmp180_read_adc_press(data, &adc_press);
	if (ret)
		return ret;

	comp_press = bmp180_compensate_press(data, adc_press);

	*val = comp_press;
	*val2 = 1000;

	return IIO_VAL_FRACTIONAL;
}

static int bmp180_chip_config(struct bmp280_data *data)
{
	return 0;
}

static const int bmp180_oversampling_temp_avail[] = { 1 };
static const int bmp180_oversampling_press_avail[] = { 1, 2, 4, 8 };

static const struct bmp280_chip_info bmp180_chip_info = {
	.regmap_config = &bmp180_regmap_config,

	.oversampling_temp_avail = bmp180_oversampling_temp_avail,
	.num_oversampling_temp_avail =
		ARRAY_SIZE(bmp180_oversampling_temp_avail),

	.oversampling_press_avail = bmp180_oversampling_press_avail,
	.num_oversampling_press_avail =
		ARRAY_SIZE(bmp180_oversampling_press_avail),

	.chip_config = bmp180_chip_config,
	.read_temp = bmp180_read_temp,
	.read_press = bmp180_read_press,
};

static int bmp280_probe(struct i2c_client *client,
			const struct i2c_device_id *id)
{
	int ret;
	struct iio_dev *indio_dev;
	struct bmp280_data *data;
	unsigned int chip_id;

	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
	if (!indio_dev)
		return -ENOMEM;

	data = iio_priv(indio_dev);
	mutex_init(&data->lock);
	data->client = client;

	indio_dev->dev.parent = &client->dev;
	indio_dev->name = id->name;
	indio_dev->channels = bmp280_channels;
	indio_dev->info = &bmp280_info;
	indio_dev->modes = INDIO_DIRECT_MODE;

	switch (id->driver_data) {
	case BMP180_CHIP_ID:
		indio_dev->num_channels = 2;
		data->chip_info = &bmp180_chip_info;
		data->oversampling_press = ilog2(8);
		data->oversampling_temp = ilog2(1);
		break;
	case BMP280_CHIP_ID:
		indio_dev->num_channels = 2;
		data->chip_info = &bmp280_chip_info;
		data->oversampling_press = ilog2(16);
		data->oversampling_temp = ilog2(2);
		break;
	case BME280_CHIP_ID:
		indio_dev->num_channels = 3;
		data->chip_info = &bme280_chip_info;
		data->oversampling_press = ilog2(16);
		data->oversampling_humid = ilog2(16);
		data->oversampling_temp = ilog2(2);
		break;
	default:
		return -EINVAL;
	}

	data->regmap = devm_regmap_init_i2c(client,
					data->chip_info->regmap_config);
	if (IS_ERR(data->regmap)) {
		dev_err(&client->dev, "failed to allocate register map\n");
		return PTR_ERR(data->regmap);
	}

	ret = regmap_read(data->regmap, BMP280_REG_ID, &chip_id);
	if (ret < 0)
		return ret;
	if (chip_id != id->driver_data) {
		dev_err(&client->dev, "bad chip id.  expected %lx got %x\n",
			id->driver_data, chip_id);
		return -EINVAL;
	}

	ret = data->chip_info->chip_config(data);
	if (ret < 0)
		return ret;

	return devm_iio_device_register(&client->dev, indio_dev);
}

static const struct acpi_device_id bmp280_acpi_match[] = {
	{"BMP0280", BMP280_CHIP_ID },
	{"BMP0180", BMP180_CHIP_ID },
	{"BMP0085", BMP180_CHIP_ID },
	{"BME0280", BME280_CHIP_ID },
	{ },
};
MODULE_DEVICE_TABLE(acpi, bmp280_acpi_match);

static const struct i2c_device_id bmp280_id[] = {
	{"bmp280", BMP280_CHIP_ID },
	{"bmp180", BMP180_CHIP_ID },
	{"bmp085", BMP180_CHIP_ID },
	{"bme280", BME280_CHIP_ID },
	{ },
};
MODULE_DEVICE_TABLE(i2c, bmp280_id);

static struct i2c_driver bmp280_driver = {
	.driver = {
		.name	= "bmp280",
		.acpi_match_table = ACPI_PTR(bmp280_acpi_match),
	},
	.probe		= bmp280_probe,
	.id_table	= bmp280_id,
};
module_i2c_driver(bmp280_driver);

MODULE_AUTHOR("Vlad Dogaru <vlad.dogaru@intel.com>");
MODULE_DESCRIPTION("Driver for Bosch Sensortec BMP180/BMP280 pressure and temperature sensor");
MODULE_LICENSE("GPL v2");